Search Results

Search found 5946 results on 238 pages for 'heavy bytes'.

Page 112/238 | < Previous Page | 108 109 110 111 112 113 114 115 116 117 118 119  | Next Page >

• How does btrfs RAID work in degraded mode?

  - by turbo

  My idea was that (using loopback devices) it works like this Create the raid array sudo mkfs.btrfs -m raid1 -d raid1 /dev/loop1 /dev/loop2 You mount them sudo mount /dev/loop1 /mnt and mark them touch goodcondition You unmount and simulate disk failure (remove disk or delete loopback device loop2 in my case) You mount degraded -o degraded and mark again touch degraded You add the bad disk again sudo btrfs dev add /dev/loop2 You rebalance sudo btrfs fi ba /mnt And Raid 1 should work again. But that's not the case. sudo btrfs fi show: Total devices 3 FS bytes used 28.00KB devid 3 size 4.00GB used 264.00MB path /dev/loop1 devid 2 size 4.00GB used 272.00MB path /dev/loop2 *** Some devices missing The file degraded lives on loop1 but not on loop2 when loop2 is mounted in degraded mode. Why is that?

  Read the article

• Repeated disconnects on WPA PEAP network

  - by exasperated

  My school has a WPA PEAP network with GTC inner authentication. I am able to connect to the network, but once I load a website or two, the network become unresponsive (i.e. in Chromium, it gets stuck at "Sending request"), and I'm eventually disconnected. Any help will be greatly appreciated. Here's some log output. I can provide more if needed: Ubuntu 13.04 3.8.0-32-generic x86_64 lsusb: 03:00.0 Network controller: Intel Corporation Centrino Advanced-N 6235 (rev 24) lsmod: iwldvm                241872  0  mac80211              606457  1 iwldvm iwlwifi               173516  1 iwldvm cfg80211              511019  3 iwlwifi,mac80211,iwldvm dmesg: [    3.501227] iwlwifi 0000:03:00.0: irq 46 for MSI/MSI-X [    3.503541] iwlwifi 0000:03:00.0: loaded firmware version 18.168.6.1 [    3.527153] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEBUG disabled [    3.527162] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEBUGFS enabled [    3.527170] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEVICE_TRACING enabled [    3.527178] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEVICE_TESTMODE enabled [    3.527186] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_P2P disabled [    3.527192] iwlwifi 0000:03:00.0: Detected Intel(R) Centrino(R) Advanced-N 6235 AGN, REV=0xB0 [    3.527240] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [    3.551049] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [  375.153065] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [  375.159727] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [  375.553201] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [  375.559871] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 1892.110738] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 1892.117357] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 5227.235372] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 5227.242122] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 5817.817954] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 5817.824560] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 5824.571917] iwlwifi 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 5824.571929] iwlwifi 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 5824.571935] iwlwifi 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [ 6956.290061] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 6956.296671] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 6963.080560] iwlwifi 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 6963.080566] iwlwifi 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 6963.080570] iwlwifi 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [ 7613.469241] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 7613.475870] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 7620.201265] iwlwifi 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 7620.201278] iwlwifi 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 7620.201285] iwlwifi 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [ 8232.762453] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 8232.769065] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 8239.581772] iwlwifi 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 8239.581784] iwlwifi 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 8239.581792] iwlwifi 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [13763.634808] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [13763.641427] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [16955.598953] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [16955.605574] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 lshw:    *-network        description: Wireless interface        product: Centrino Advanced-N 6235        vendor: Intel Corporation        physical id: 0        bus info: pci@0000:03:00.0        logical name: wlan0        version: 24        serial: b4:b6:76:a0:4b:3c        width: 64 bits        clock: 33MHz        capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless        configuration: broadcast=yes driver=iwlwifi driverversion=3.8.0-32-generic firmware=18.168.6.1 ip=10.250.169.96 latency=0 link=yes multicast=yes wireless=IEEE 802.11abgn        resources: irq:46 memory:f7c00000-f7c01fff iwlist scan: Cell 02 - Address: 24:DE:C6:B0:C7:D9                     Channel:36                     Frequency:5.18 GHz (Channel 36)                     Quality=29/70  Signal level=-81 dBm                       Encryption key:on                     ESSID:"CatChat2x"                     Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s                               36 Mb/s; 48 Mb/s; 54 Mb/s                     Mode:Master                     Extra:tsf=0000004ff3fe419b                     Extra: Last beacon: 27820ms ago                     IE: Unknown: 0009436174436861743278                     IE: Unknown: 01088C129824B048606C                     IE: Unknown: 030124                     IE: IEEE 802.11i/WPA2 Version 1                         Group Cipher : CCMP                         Pairwise Ciphers (1) : CCMP                         Authentication Suites (1) : 802.1x                     IE: Unknown: 2D1ACC011BFFFF000000000000000000000000000000000000000000                     IE: Unknown: 3D1624001B000000FF000000000000000000000000000000                     IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00                     IE: Unknown: DD1E00904C33CC011BFFFF000000000000000000000000000000000000000000                     IE: Unknown: DD1A00904C3424001B000000FF000000000000000000000000000000           Cell 04 - Address: 24:DE:C6:B0:C3:E9                     Channel:149                     Frequency:5.745 GHz                     Quality=28/70  Signal level=-82 dBm                       Encryption key:on                     ESSID:"CatChat2x"                     Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s                               36 Mb/s; 48 Mb/s; 54 Mb/s                     Mode:Master                     Extra:tsf=000000181f60e19c                     Extra: Last beacon: 28680ms ago                     IE: Unknown: 0009436174436861743278                     IE: Unknown: 01088C129824B048606C                     IE: Unknown: 030195                     IE: Unknown: 050400010000                     IE: IEEE 802.11i/WPA2 Version 1                         Group Cipher : CCMP                         Pairwise Ciphers (1) : CCMP                         Authentication Suites (1) : 802.1x                     IE: Unknown: 2D1ACC011BFFFF000000000000000000000000000000000000000000                     IE: Unknown: 3D1695001B000000FF000000000000000000000000000000                     IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00                     IE: Unknown: DD1E00904C33CC011BFFFF000000000000000000000000000000000000000000                     IE: Unknown: DD1A00904C3495001B000000FF000000000000000000000000000000                     IE: Unknown: DD07000B8601040817                     IE: Unknown: DD0E000B860103006170313930333032           Cell 09 - Address: 24:DE:C6:B0:C0:29                     Channel:149                     Frequency:5.745 GHz                     Quality=39/70  Signal level=-71 dBm                       Encryption key:on                     ESSID:"CatChat2x"                     Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s                               36 Mb/s; 48 Mb/s; 54 Mb/s                     Mode:Master                     Extra:tsf=00000112fb688ede                     Extra: Last beacon: 27716ms ago ifconfig (while connected): wlan0     Link encap:Ethernet  HWaddr b4:b6:76:a0:4b:3c             inet addr:10.250.16.220  Bcast:10.250.31.255  Mask:255.255.240.0           inet6 addr: fe80::b6b6:76ff:fea0:4b3c/64 Scope:Link           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1           RX packets:230023 errors:0 dropped:0 overruns:0 frame:0           TX packets:130970 errors:0 dropped:0 overruns:0 carrier:0           collisions:0 txqueuelen:1000            RX bytes:255999759 (255.9 MB)  TX bytes:16652605 (16.6 MB) iwconfig (while connected): wlan0     IEEE 802.11abgn  ESSID:"CatChat2x"             Mode:Managed  Frequency:5.745 GHz  Access Point: 24:DE:C6:B0:C0:29              Bit Rate=6 Mb/s   Tx-Power=15 dBm              Retry  long limit:7   RTS thr:off   Fragment thr:off           Power Management:off           Link Quality=36/70  Signal level=-74 dBm             Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0           Tx excessive retries:0  Invalid misc:3   Missed beacon:0

  Read the article

• Metsys.Bson - the BSON Library

  Earlier this month I detailed the implementation of the bson serialization we used in Norm - the C# MongoDB driver. I've since extracted the serialization/deserialization code and created a standalone project for it - in the hopes that it might prove helpful to someone. If you need an efficient binary protocol to transfer data, look no further. There are two methods you need to be aware of: Serializer.Serialize and Deserializer.Deserialize. User u1 = new User{...}; byte[] bytes = Serializer.Serialize(u1); User...Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• Possibility of recovering files from a dd zero-filled hard disk

  - by unknownthreat

  I have "zero filled" (complete wiped) an external hard disk using dd, and from what I have heard: people said you should at least "zero fill" 3 times to be sure that the data are really wiped and no one can recover anything. So I decided to scan the disk once again after I've zero filled the disk. I was expecting the disk to still have some random binary left. It turned out that it has only a few sequential bytes in the very beginning. This is probably the file structure type and other headers stuff. Other than that, it's all zeros and nothing else. So if we have to recover any file from a zero filled disk, ...how? From what I've heard, even you zero fill the disk, you should still have some data left. ...or could dd really completely annihilate all data?

  Read the article

• Problem with Free sapce

  - by Andrew Neely

  I was zeroing out the free space on my Ubuntu 12.04 using sfill, when the command stopped responding and I had to reboot the machine. Now, the system says that it has no space left, and that it is running in low graphics mode. Before this happened, I had nearly 500 gig free. df says there are 0 bytes free. df -i reports only 2% of INODES used. I've run fsck and it didn't resolve the issue. What can I do to resolve the issue?

  Read the article

• Computer Science Fundamentals - Recommended books

  - by contactmatt

  Hey, I'm looking to see if anyone can recommend any books in fundamentals of computer science. I obtained my associates degree as a programmer/analyst a couple years ago and I know a good amount about programming on the .NET framework. I'm even certified on the .NET 4 framework as a web application developer. However, since I was only able to obtain my associates degree, I was deprived at my college on the low-level basics and operations of computers and basic computer science information. I'm really interesting in learning about the low-level operations of a computer and in programming (bytes, bits, memory management, etc.) Can anyone recommend any good computer science books for someone who is decently experienced in programming? Thank You

  Read the article

• Connected to wifi, but quits loading pages after a random amount of time

  - by Collin

  I'm using Ubuntu 12.10, on a TOSHIBA Satellite L755 laptop, and using a Cradlepoint MBR-1000 wireless router. The wifi supposedly works fine on my sisters' and mom's laptops, and my dad uses a wired connection through the router. Nobody else has the problem. It shows that I'm connected and everything. The network manager GUI shows that everything is going just dandy... but it's not. I'll be able to load a page or two, then I have to disconnect, and reconnect to the router to get it to work again for a couple minutes. I noticed when I was downstairs, close to the router, this problem seemed to go away (at least, I was connected for a couple of hours without running into this problem). When I run ping -n 8.8.8.8 it shows this while the connection is still running fine 64 bytes from 8.8.8.8: icmp_req=1187 ttl=47 time=665 ms and whe

  Read the article

• file copy error from system to cifs mount

  - by dwpriest

  When coping a file greater than 64kB from an Ubuntu server to a CIFS mounted windows share, most of the data is copied, but it seems the last chunk doesn't get copied. The size doesn't match, and the md5 check sums don't match. I have plenty of file space, but then I use cp, I get the following... cp: closing `cloudBackup/asdf.txt': No space left on device Using rsync, I get the following... rsync: close failed on "/home/fluffy/cloudBackup/.asdf.txt.qrBWe6": No space left on device (28) rsync error: error in file IO (code 11) at receiver.c(752) [receiver=3.0.8] rsync: connection unexpectedly closed (29 bytes received so far) [sender] rsync error: error in rsync protocol data stream (code 12) at io.c(601) [sender=3.0.8] I have full read/write permissions on the mounted share. I can copy locally and between the mount and system via SSH just fine. Any ideas? Thank you

  Read the article

• When attempting to install ubuntu 12.04 from CD, I am stuck on black streen with "loading bootlogo..."

  - by Jessica K

  I downloaded Ubuntu 12.04 to my desktop and burned to a CD using Infra Recorder and instructions on ubuntu website. Restarted PC to boot from CD receive black screen with "Loading bootlogo..." then nothing happens and I have to restart with windows. The CD seems to be correct. Folders include .disk, boot, casper, dists, install, isolinux, pics, pool, preseed, autorun file, md5sum text file, readme.diskdefines file, wubi app. System Information Operating System: Windows Vista™ Home Premium (6.0, Build 6002) Service Pack 2 (6002.vistasp2_gdr.120824-0336) System Manufacturer: TOSHIBA System Model: Satellite L305 BIOS: Default System BIOS Processor: Intel(R) Pentium(R) Dual CPU T2390 @ 1.86GHz (2 CPUs), ~1.9GHz Memory: 3062MB RAM Page File: 1553MB used, 4772MB available Windows Dir: C:\Windows DirectX Version: DirectX 11 DX Setup Parameters: Not found DxDiag Version: 7.00.6002.18107 32bit Unicode Drive: D: Model: PIONEER DVD-RW DVRKD08L ATA Device Driver: c:\windows\system32\drivers\cdrom.sys, 6.00.6002.18005 (English), 4/11/2009 00:39:17, 67072 bytes

  Read the article

• How to convert a Bazaar repository to GIT repository?

  - by Naruto Uzumaki

  We have a large bazaar repository and we want to convert it to a git repository. The bazaar repository contains the folders of each of the interns. Any documentation/code prepared by interns is committed in their directory so there are a huge number of commits. What steps should be performed to securely convert the bazaar repository to a git repository so that we do not lose any commit information. We firstly need to create a backup of the existing bazaar repository and then convert it. Edit: I followed this link: http://librelist.com/browser//cville/2010/2/9/migrate-repository-bzr-to-git/ It's working fine on my system with Ubuntu. But when I try to run it on the actual server it gives me EOF error and crashes Starting export of 1036 revisions ... fatal: EOF in data (1825 bytes remaining) fast-import: dumping crash report to .git/fast_import_crash_11804 Edit 2: I also tried it on a new CentOS system and received the following error fatal: ambiguous argument 'HEAD': unknown revision or path not in the working tree. Use '--' to separate paths from revisions

  Read the article

• Code Contracts: How they look after compiling?

  - by DigiMortal

  When you are using new tools that make also something at code level then it is good idea to check out what additions are made to code during compilation. Code contracts have simple syntax when we are writing code at Visual Studio but what happens after compilation? Are our methods same as they look in code or are they different after compilation? In this posting I will show you how code contracts look after compiling. In my previous examples about code contracts I used randomizer class with method called GetRandomFromRangeContracted. public int GetRandomFromRangeContracted(int min, int max) {     Contract.Requires<ArgumentOutOfRangeException>(         min < max,         "Min must be less than max"     );       Contract.Ensures(         Contract.Result<int>() >= min &&         Contract.Result<int>() <= max,         "Return value is out of range"     );       return _generator.Next(min, max); } Okay, it is nice to dream about similar code when we open our assembly with Reflector and disassemble it. But… this time we have something interesting. While reading this code don’t feel uncomfortable about the names of variables. This is disassembled code. .NET Framework internally allows these names. It is our compilators that doesn’t accept them when we are building our code. public int GetRandomFromRangeContracted(int min, int max) {     int Contract.Old(min);     int Contract.Old(max);     if (__ContractsRuntime.insideContractEvaluation <= 4)     {         try         {             __ContractsRuntime.insideContractEvaluation++;             __ContractsRuntime.Requires<ArgumentOutOfRangeException>(                min < max,                "Min must be less than max", "min < max");         }         finally         {             __ContractsRuntime.insideContractEvaluation--;         }     }     try     {         Contract.Old(min) = min;     }     catch (Exception exception1)     {         if (exception1 == null)         {             throw;         }     }     try     {         Contract.Old(max) = max;         catch (Exception exception2)     {         if (exception2 == null)         {             throw;         }     }     int CS$1$0000 = this._generator.Next(min, max);     int Contract.Result<int>() = CS$1$0000;     if (__ContractsRuntime.insideContractEvaluation <= 4)     {         try         {             __ContractsRuntime.insideContractEvaluation++;             __ContractsRuntime.Ensures(                (Contract.Result<int>() >= Contract.Old(min)) &&                (Contract.Result<int>() <= Contract.Old(max)),                "Return value is out of range",                "Contract.Result<int>() >= min && Contract.Result<int>() <= max");         }         finally         {             __ContractsRuntime.insideContractEvaluation--;         }     }     return Contract.Result<int>(); } As we can see then contracts are not simply if-then-else checks and exceptions throwing. We can see that there is counter that is incremented before checks and decremented after these whatever the result of check was. One thing that is annoying for me are null checks for exception1 and exception2. Is there really some situation possible when null is thrown instead of some instance that is Exception or that inherits from exception? Conclusion Code contracts are more complex mechanism that it seems when we look at it on our code level. Internally there are done more things than we know. I don’t say it is wrong, it is just good to know how our code looks after compiling. Looking at this example it is sure we need also performance tests for contracted code to see how heavy is their impact to system performance when we run code that makes heavy use of code contracts.

  Read the article

• Best way to store motion changes to reduce memory

  - by Andrew Simpson

  I am comparing jpeg to jpeg in a constant 'video-stream'. i am using EMGU/OpenCV to compare each pixels at the byte level. There are 3 channels to each image (RGB). I had heard that it is common practice to store only the pixels that have changed between frames as a way of conserving memory space. But, if for instance/example I say EVERY pixel has changed (pls note i am using an exaggerated example to make my point and i would normally discard such large changes) then the resultant bytes saved is 3 times larger than the original jpeg. How can I store such motion changes efficiently? thanks

  Read the article

• Wiped data, and duplicated folders into files.

  - by Kaustubh P

  Something weird happened today, and I dont know how. Within a folder, all folders have a file by the same name, with a colon appended to it. And all the files from the most inner-most directory in my home, have been dumped to ~, with a size of 0 bytes. I have not executed any scripts or anything. I was just checking out some easter eggs, namely the gegls from outer space and free the fish and was away from the computer and was logged because of the screensaver. I couldnt log-back in with my password, so I just reset the PC, and while booting, the PC went into a drive check. BUT, IIRC, i saw the duplicate "folder files" before I had logged out, so thats not the reason! All the files have a timestamp of 14 Jan. Also, the contents of my eclipse folder have been dumped into ~. Right down to the jars and ini files. HELP!

  Read the article

• How can I determine which GPU card is running at PCI Express 2.0 x16 & which is using x8?

  - by M. Tibbits

  Is there a way to determine the speed of the PCI Express connection to a specific card? I have three cards plugged in: two Nvidia GTX 480's (one at x16 & and one at x8) one Nvidia GTX 460 running at x8 Is there some way, either by a function call in C or an option to lspci that I can determine the bus speed of the graphics cards? When I only use one of the cards for my CUDA program, I'd like to use the one which is running at x16. Thanks! Note: lspci -vvv dumps out For the two GTX 480s. I don't see any differences that pertain to bus speed. 03:00.0 VGA compatible controller: nVidia Corporation Device 06c0 (rev a3) Subsystem: eVga.com. Corp. Device 1480 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at d4000000 (32-bit, non-prefetchable) [size=32M] Region 1: Memory at b0000000 (64-bit, prefetchable) [size=128M] Region 3: Memory at bc000000 (64-bit, prefetchable) [size=64M] Region 5: I/O ports at df00 [disabled] [size=128] [virtual] Expansion ROM at b8000000 [disabled] [size=512K] Capabilities: <access denied> Kernel driver in use: nvidia Kernel modules: nvidia, nvidiafb, nouveau 03:00.1 Audio device: nVidia Corporation Device 0be5 (rev a1) Subsystem: eVga.com. Corp. Device 1480 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 5 Region 0: [virtual] Memory at d7ffc000 (32-bit, non-prefetchable) [disabled] [size=16K] Capabilities: <access denied> 04:00.0 VGA compatible controller: nVidia Corporation Device 06c0 (rev a3) Subsystem: eVga.com. Corp. Device 1480 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at dc000000 (32-bit, non-prefetchable) [size=32M] Region 1: Memory at c0000000 (64-bit, prefetchable) [size=128M] Region 3: Memory at cc000000 (64-bit, prefetchable) [size=64M] Region 5: I/O ports at cf00 [size=128] [virtual] Expansion ROM at c8000000 [disabled] [size=512K] Capabilities: <access denied> Kernel driver in use: nvidia Kernel modules: nvidia, nvidiafb, nouveau 04:00.1 Audio device: nVidia Corporation Device 0be5 (rev a1) Subsystem: eVga.com. Corp. Device 1480 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 5 Region 0: Memory at dfffc000 (32-bit, non-prefetchable) [size=16K] Capabilities: <access denied> And the only differences I see relate specifically to the memory mapping: myComputer:~> diff card1 card2 3c3 < Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- --- > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- 7,11c7,11 < Region 0: Memory at d4000000 (32-bit, non-prefetchable) [size=32M] < Region 1: Memory at b0000000 (64-bit, prefetchable) [size=128M] < Region 3: Memory at bc000000 (64-bit, prefetchable) [size=64M] < Region 5: I/O ports at df00 [disabled] [size=128] < [virtual] Expansion ROM at b8000000 [disabled] [size=512K] --- > Region 0: Memory at dc000000 (32-bit, non-prefetchable) [size=32M] > Region 1: Memory at c0000000 (64-bit, prefetchable) [size=128M] > Region 3: Memory at cc000000 (64-bit, prefetchable) [size=64M] > Region 5: I/O ports at cf00 [size=128] > [virtual] Expansion ROM at c8000000 [disabled] [size=512K] 18c18 < Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- --- > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- 19a20 > Latency: 0, Cache Line Size: 64 bytes 21c22 < Region 0: [virtual] Memory at d7ffc000 (32-bit, non-prefetchable) [disabled] [size=16K] --- > Region 0: Memory at dfffc000 (32-bit, non-prefetchable) [size=16K]

  Read the article

• WHMCS Fatal error: Out of memory while View Invoice PDF

  - by prakash

  I can log into WHMCS & can access everything I should be able to access, but if i try to click View PDF Invoice, the following error will occur, Fatal error: Out of memory (allocated 67633152) (tried to allocate 76 bytes) in /home/xxxx/public_html/whmcs/includes/classes/class.tcpdf.php on line 8419 I have already set the allocated Memory limit to 256MB, but the error still occurs. At that time of the error, the process memory is exceeding the allocation I set. I checked log file, and found the following errors: #2 /home/xxxxx/public_html/client/includes/classes/class.tcpdf.php(8453): TCPDF->Image('/home/xxxxx/...', 20, 25, 75, 17.5816023739, 'PNG', '', '', false, 300, '', false, 8) #3 /home/xxxxx/public_html/client/includes/classes/class.tcpdf.php(7881): TCPDF->ImagePngAlpha('/home/xxxxx/...', 20, 25, 337, 79, 75, 17.5816023739, 'PNG', '', '', false, 300, '', NULL) While I was investigating the issue above I also noticed the error condition pictured below:

  Read the article

• Cocos2d update leaking memory

  - by Andrey Chernukha

  I have a weird issue - my app is leaking memory on device only, not on a simulator. It is leaking if i schedule update method anywhere, on any scene. It is leaking despite update method is empty, there's nothing inside it except NSLog. How can it be? I have even scheduled update on the very first scene where it seems there's nothing to leak, and scheduled another empty and it's leaking or not leaking but allocating something, the result is the same - the volume of the memory consumed is increasing and my app is crashing soon. I can detect the leakage via using Instruments-Memory-Activity Monitor or with help of following function: void report_memory(void) { struct task_basic_info info; mach_msg_type_number_t size = sizeof(info); kern_return_t kerr = task_info(mach_task_self(), TASK_BASIC_INFO, (task_info_t)&info, &size); if( kerr == KERN_SUCCESS ) { NSLog(@"Memory in use (in bytes): %u", info.resident_size); } else { NSLog(@"Error with task_info(): %s", mach_error_string(kerr)); } } Can anyone explain me what's going on?

  Read the article

• Edit 100MB+ file

  - by Majid Fouladpour

  I have captured some traffic with Wireshark and saved the result as a file. The file has 3 sections now: request headers response headers response body The response body is to become an flv file, but now everything is saved as a single file. So I need a way to delete the first two sections from the file, but the problem is that the file is very big (over a thousand mega bytes). I have tried to open it with gedit, but no matter how long I wait, gedit hangs and remains unresponsive until I kill it. What tool can I use to edit this big file easily?

  Read the article

• How to emulate Mode 13h in a modern 3D renderer?

  - by David Gouveia

  I was indulging in nostalgia and remembered the first game I created, which used Mode 13h. This mode was really simple to work with, since it was essentially just an array of bytes with an element for each pixel on the screen (using an indexed color scheme). So I thought it might be fun to create something nowadays under these restrictions, but on modern hardware. The API could be as simple as: public class Mode13h { public byte[] VideoMemory = new byte[320 * 200]; public Color[] Palette = new Color[256]; } Now I'm wondering what would be the best way to get this data on the screen, using something like XNA / DirectX / OpenGL. The only solution I could think of was to create a texture with the same size as the VideoMemory array, write the contents of VideoMemory to it every frame, then render that texture in a full screen quad with the correct aspect ratio and using point texture filtering for that retro look. Is there a better way?

  Read the article

• SQL Server - Rebuilding Indexes

  - by Renso

  Goal: Rebuild indexes in SQL server. This can be done one at a time or with the example script below to rebuild all index for a specified table or for all tables in a given database. Why? The data in indexes gets fragmented over time. That means that as the index grows, the newly added rows to the index are physically stored in other sections of the allocated database storage space. Kind of like when you load your Christmas shopping into the trunk of your car and it is full you continue to load some on the back seat, in the same way some storage buffer is created for your index but once that runs out the data is then stored in other storage space and your data in your index is no longer stored in contiguous physical pages. To access the index the database manager has to "string together" disparate fragments to create the full-index and create one contiguous set of pages for that index. Defragmentation fixes that. What does the fragmentation affect?Depending of course on how large the table is and how fragmented the data is, can cause SQL Server to perform unnecessary data reads, slowing down SQL Server’s performance.Which index to rebuild?As a rule consider that when reorganize a table's clustered index, all other non-clustered indexes on that same table will automatically be rebuilt. A table can only have one clustered index.How to rebuild all the index for one table:The DBCC DBREINDEX command will not automatically rebuild all of the indexes on a given table in a databaseHow to rebuild all indexes for all tables in a given database:USE [myDB]    -- enter your database name hereDECLARE @tableName varchar(255)DECLARE TableCursor CURSOR FORSELECT table_name FROM information_schema.tablesWHERE table_type = 'base table'OPEN TableCursorFETCH NEXT FROM TableCursor INTO @tableNameWHILE @@FETCH_STATUS = 0BEGINDBCC DBREINDEX(@tableName,' ',90)     --a fill factor of 90%FETCH NEXT FROM TableCursor INTO @tableNameENDCLOSE TableCursorDEALLOCATE TableCursorWhat does this script do?Reindexes all indexes in all tables of the given database. Each index is filled with a fill factor of 90%. While the command DBCC DBREINDEX runs and rebuilds the indexes, that the table becomes unavailable for use by your users temporarily until the rebuild has completed, so don't do this during production  hours as it will create a shared lock on the tables, although it will allow for read-only uncommitted data reads; i.e.e SELECT.What is the fill factor?Is the percentage of space on each index page for storing data when the index is created or rebuilt. It replaces the fill factor when the index was created, becoming the new default for the index and for any other nonclustered indexes rebuilt because a clustered index is rebuilt. When fillfactor is 0, DBCC DBREINDEX uses the fill factor value last specified for the index. This value is stored in the sys.indexes catalog view. If fillfactor is specified, table_name and index_name must be specified. If fillfactor is not specified, the default fill factor, 100, is used.How do I determine the level of fragmentation?Run the DBCC SHOWCONTIG command. However this requires you to specify the ID of both the table and index being. To make it a lot easier by only requiring you to specify the table name and/or index you can run this script:DECLARE@ID int,@IndexID int,@IndexName varchar(128)--Specify the table and index namesSELECT @IndexName = ‘index_name’    --name of the indexSET @ID = OBJECT_ID(‘table_name’)  -- name of the tableSELECT @IndexID = IndIDFROM sysindexesWHERE id = @ID AND name = @IndexName--Show the level of fragmentationDBCC SHOWCONTIG (@id, @IndexID)Here is an example:DBCC SHOWCONTIG scanning 'Tickets' table...Table: 'Tickets' (1829581556); index ID: 1, database ID: 13TABLE level scan performed.- Pages Scanned................................: 915- Extents Scanned..............................: 119- Extent Switches..............................: 281- Avg. Pages per Extent........................: 7.7- Scan Density [Best Count:Actual Count].......: 40.78% [115:282]- Logical Scan Fragmentation ..................: 16.28%- Extent Scan Fragmentation ...................: 99.16%- Avg. Bytes Free per Page.....................: 2457.0- Avg. Page Density (full).....................: 69.64%DBCC execution completed. If DBCC printed error messages, contact your system administrator.What's important here?The Scan Density; Ideally it should be 100%. As time goes by it drops as fragmentation occurs. When the level drops below 75%, you should consider re-indexing.Here are the results of the same table and clustered index after running the script:DBCC SHOWCONTIG scanning 'Tickets' table...Table: 'Tickets' (1829581556); index ID: 1, database ID: 13TABLE level scan performed.- Pages Scanned................................: 692- Extents Scanned..............................: 87- Extent Switches..............................: 86- Avg. Pages per Extent........................: 8.0- Scan Density [Best Count:Actual Count].......: 100.00% [87:87]- Logical Scan Fragmentation ..................: 0.00%- Extent Scan Fragmentation ...................: 22.99%- Avg. Bytes Free per Page.....................: 639.8- Avg. Page Density (full).....................: 92.10%DBCC execution completed. If DBCC printed error messages, contact your system administrator.What's different?The Scan Density has increased from 40.78% to 100%; no fragmentation on the clustered index. Note that since we rebuilt the clustered index, all other index were also rebuilt.

  Read the article

• How does PHP internally represent strings?

  - by Jim Thio

  UTF8? UTF16? Do strings in PHP also keep track of the encoding used? Let's look at this script for example. Say I run: $original = "??????????????"; What actually happens? Obviously I think $original will not contain just 7 characters. Those glyphs must each be represented by several bytes there. Then I do: $converted = mb_convert_encoding ($original , "UTF-8"); What will happen to $converted? How will $converted be different from $original? Will it be just the exact same byte sequence as $original but with a different encoding?

  Read the article

• Is there any difference between processor and core?

  - by Salvador

  The following two command seems to give me different information about the same hardware srs@ubuntu:~$ cat /proc/cpuinfo | grep -e processor -e cores processor : 0 cpu cores : 4 processor : 1 cpu cores : 4 processor : 2 cpu cores : 4 processor : 3 cpu cores : 4 srs@ubuntu:~$ sudo dmidecode -t processor # dmidecode 2.9 SMBIOS 2.6 present. Handle 0x0004, DMI type 4, 42 bytes Processor Information Socket Designation: LGA1155 Type: Central Processor Family: <OUT OF SPEC> Manufacturer: Intel ID: A7 06 02 00 FF FB EB BF Version: Intel(R) Core(TM) i5-2500K CPU @ 3.30GHz Voltage: 1.0 V External Clock: 100 MHz Max Speed: 3800 MHz Current Speed: 3300 MHz Status: Populated, Enabled Upgrade: Other L1 Cache Handle: 0x0005 L2 Cache Handle: 0x0006 L3 Cache Handle: 0x0007 Serial Number: To Be Filled By O.E.M. Asset Tag: To Be Filled By O.E.M. Part Number: To Be Filled By O.E.M. Core Count: 4 Core Enabled: 1 Characteristics: 64-bit capable Until today I thought I had a single processor with 4 independent cores. I also thought that within each core can be used different threads.

  Read the article

• Windows Error After Wubi Install

  - by user106563

  The initial install on my laptop was Windows 7. I installed Wubi on Sunday - the install seemed fine. I was able to log in and use both Ubuntu and Windows. On Monday I started receiving the following error in Windows: windows cannot access the specified device path or file This occurs on every link I click on - essentially rendering Windows unusable. I do not experience the same problem when Windows is started up in safe mode. I have tried numerous virus scans (Malware bytes, Avg, AdAware) and have removed various trojans etc. Windows is still unusable. Ubuntu seems fine so far. My question is, can this error be attributed to the Wubi install?

  Read the article

• How do you get the total asset size (or total resource size) in an Android game?

  - by tom_mai78101

  In an Android Java project, there are two folders, asset and res. To me, I usually put some stuffs, like PNG files, sound files, etc. in either one of the two folder. When resources are increasingly becoming more and more in those folders, the time it takes to load them will increase. Therefore, a loading screen is a must in these situation. The total size is to be used in a loading screen, so that I can guess the average time it takes to load each resources, from 0 bytes to its individual resource file size. I only know that by adding all individual sizes in a respective order, I will then obtain the total asset or res folder size, simply by adding them up. So, when it comes to getting the total file size from either folder, how do you obtain their individual resource/object sizes, respectively? Thanks in advance.

  Read the article

• Interface extension

  - by user877329

  Suppose that I have an input stream interface, which defines a method for reading data. I also have a seekable interface which defines a method for seeking. A natural way of defining a input file is then to implement both input stream and seekable. I want to construct a data decoder from the input stream interface so I can read data from a file or from another stream. The problem is that I also want to implement seek functionality to the data decoder, since I want to be able to step individual records not raw bytes. This is not possible if I only provide an input stream, which does not have the bytewise seek method. Should I skip the seekable interface and add the seek method to input stream instead and force all streams to at least leave it as a nop.

  Read the article

• How to implement Fog Of War with an shader?

  - by Cambrano

  Okay, I'm creating a RTS game and want to implement an AgeOfEmpires-like Fog Of War(FOW). That means a tile(or pixel) can be: 0% transparent (unexplored) 50% transparent black (explored but not in viewrange) 100% transparent(explored and in viewrange) RTS means I'll have many explorers (NPCs, buildings, ...). Okay, so I have an 2d array of bytes byte[,] explored. The byte value correlates the transparency. The question is, how do I pass this array to my shader? Well I think it is not possible to pass an entire array. So: what technique shall I use to let my shader know if a pixel/tile is visible or not?

  Read the article

< Previous Page | 108 109 110 111 112 113 114 115 116 117 118 119  | Next Page >