Search Results

Search found 4161 results on 167 pages for 'desmond lost'.

Page 113/167 | < Previous Page | 109 110 111 112 113 114 115 116 117 118 119 120  | Next Page >

• Rebuild Apple RAID set

  - by Clinton Blackmore

  We have a Mac Pro tower with an Apple RAID card in it using third party drives. When one drive failed, we replaced it and the RAID 5 set was nearly done rebuilding when the computer was rebooted. It did not come back up. We are now booting up off of a different internal volume, and have three (third-party) drives of identical spec (including revision and firmware) in the box. One of the drives is a global spare; the other two are recognized as belong to a RAID set but are in "Roaming" mode. The intention is to recreate the three-drive RAID set using the data on the two drives that are good. When we tell the system to create a RAID 5 using the three drives, it tells us that it'll create a RAID set but everything will be lost. There are no obvious options to rebuild a RAID using the two good drives and incorporating the third drive in Apple's RAID Utility, and we've looked through the options for the raidutil command. Fortunately, all important data is backed up, and we can rebuild from scratch, but, is there any way to make the RAIDset work again?

  Read the article

• Gray Progress Bar in Macbook Boot caused by Partition Fault

  - by Konstantin Bodnya

  Here's my problem: When I try to load my macbook it shows the gray progress bar. It takes a while to fill the whole progress and after it macbook just shuts down. I tried to boot from recovery partition and run Disk Utility to repair it. Disk Utility showed my "Macintosh HD" in a gray color and failed to repair it. I thought all my data was lost, but then I tried the following: So I booted into ubunto from live usb and it successfully mounted my macintosh hd hfs+ partition. Parted shows me the following partitions on my disk: Disk /dev/sda: 500GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 20.5kB 210MB 210MB fat32 EFI System Partition boot 2 210MB 499GB 499GB hfs+ Macintosh HD 3 499GB 500GB 650MB hfs+ Recovery HD Seems legit except for FAT32 for EFI System Partition. Since all my data is okay and backed up what should I do to recover the system. I don't really want to reinstall all the system though I believe there's a command to make it allright in linux. Thank you everyone!

  Read the article

• Route traffic from one VPN to a second VPN

  - by Dominic

  I have set up an OpenVPN server on my windows 7 64-bit PC. I also have a subscription to a VPN service. My aim is to be able to connect my android phone to the VPN server on my PC, and then route all traffic through the VPN service. I have a NetGear WPN824 router. I can get it working if I my phone is on my local network. Then I can connect my phone to the VPN server using the local IP address of my PC. In Network Connection in the control panel, I share the connection used by the VPN service with the connection used by the VPN server. Then when I browse the internet on my phone, all traffic goes through the VPN service. Very nice. But if my phone is outside my local network, so I have to connect my phone to the local VPN using my PC's external IP address, then this method doesn't work. If I connect my PC to the VPN service and then try to connect my phone to my own VPN, it just doesn't connect (the initial TLS handshake times out). If I connect my phone to the local VPN first, then this connection is lost as soon as I connect my PC to the VPN service. Does anybody know how I can get this working? Many thanks Dominic

  Read the article

• How can I run Gnome or KDE locally in Cygwin?

  - by John Peter Thompson Garcés

  Apparently it is possible to do this using cygwin ports, as can be seen in screenshots. I followed this how-to to get apt-cygports set up, and I used it to install gnome-session. This how-to supposedly gives the commands needed to run Gnome or KDE, but whenever I try to run Gnome, a blank X-window pops up and then quickly disappears. Here is the terminal output: $ startx /usr/bin/dbus-launch gnome-session xauth: file /home/jpthomps/.serverauth.4168 does not exist Welcome to the XWin X Server Vendor: The Cygwin/X Project Release: 1.10.3.0 OS: Windows 7 Service Pack 1 [Windows NT 6.1 build 7601] (WoW64) Package: version 1.10.3-12 built 2011-08-22 XWin was started with the following command line: /usr/bin/X :0 -auth /home/jpthomps/.serverauth.4168 (II) xorg.conf is not supported (II) See http://x.cygwin.com/docs/faq/cygwin-x-faq.html for more information LoadPreferences: /home/jpthomps/.XWinrc not found LoadPreferences: Loading /etc/X11/system.XWinrc LoadPreferences: Done parsing the configuration file... winDetectSupportedEngines - DirectDraw installed, allowing ShadowDD winDetectSupportedEngines - Windows NT, allowing PrimaryDD winDetectSupportedEngines - DirectDraw4 installed, allowing ShadowDDNL winDetectSupportedEngines - Returning, supported engines 0000001f winSetEngine - Using Shadow DirectDraw NonLocking winScreenInit - Using Windows display depth of 32 bits per pixel winFinishScreenInitFB - Masks: 00ff0000 0000ff00 000000ff Screen 0 added at virtual desktop coordinate (0,0). MIT-SHM extension disabled due to lack of kernel support XFree86-Bigfont extension local-client optimization disabled due to lack of shared memory support in the kernel (II) AIGLX: Loaded and initialized /usr/lib/dri/swrast_dri.so (II) GLX: Initialized DRISWRAST GL provider for screen 0 winPointerWarpCursor - Discarding first warp: 637 478 (--) 5 mouse buttons found (--) Setting autorepeat to delay=500, rate=31 (--) Windows keyboard layout: "00000409" (00000409) "US", type 4 (--) Found matching XKB configuration "English (USA)" (--) Model = "pc105" Layout = "us" Variant = "none" Options = "none" Rules = "base" Model = "pc105" Layout = "us" Variant = "none" Options = "none" winBlockHandler - pthread_mutex_unlock() winProcEstablishConnection - winInitClipboard returned. winClipboardProc - DISPLAY=:0.0 winClipboardProc - XOpenDisplay () returned and successfully opened the display. xinit: XFree86_VT property unexpectedly has 0 items instead of 1 xinit: connection to X server lost waiting for X server to shut down winClipboardProc - winClipboardFlushWindowsMessageQueue trapped WM_QUIT message, exiting main loop. winClipboardProc - XDestroyWindow succeeded. winClipboardProc - Clipboard disabled - Exit from server winDeinitMultiWindowWM - Noting shutdown in progress

  Read the article

• MySQL encoding problem after site move

  - by Quan Zhou

  Guys, I need your help. Since last month my friend has lost his database on Dreamhost, he decided to move his wordpress based blog site (written in Chinese) to my server. He's using a wp-plugin called wp-db-backup to perform regular db backups. And the servers backgrounds are: Dreamhost: Linux 2.6.31.5-modsign-aufs2-grsec-2-opt mysql Ver 14.12 Distrib 5.0.16, for pc-linux-gnu (i386) using readline 5.0 apache2 unknown version My Server: Linux li159-46 2.6.32.12-x86_64-linode12 mysql Ver 14.14 Distrib 5.1.45, for debian-linux-gnu (x86_64) using readline 6.1 nginx 0.8.36 His site's encoding was UTF-8 in both wp-config and db. I imported his db backup file in UTF-8 by default, then I sync'd files using rsync from dreamhost, then I just changed the db address and nothing more. But when I take first look at the "new" site, it was full of unreadable characters, I met this problem before, I changed charset options in browser but none of them can make it displayed properly. Then I converted his db to GB18030, it works with only if browser set charset to GB18030 either GBK, but by default they recognize the charset as UTF-8. I tried to edit the headers but it doesn't work. What could I do now? Thx~~

  Read the article

• How have I locked me out from my Ubuntu VPS?

  - by Sanoj

  I have a Ubuntu Server as VPS (OpenVZ), and yesterday I installed php-fpm, but I guess something went wrong with the installation. Because since then I cannot log in to my server over SSH with PuTTY or using WinSCP. The message I get when connecting is Network error: Connection timed out. Immediately after the installation I was not able to use emacs either, I had to re-install it with apt-get install emacs. I have tried with clearing the firewall and rebooting the server from my web-based "control panel", but it doesn't help. The commands I used for installation of the PHP-fpm was from Installing PHP 5.3, Nginx And PHP-fpm On Ubuntu/Debian. And I guess it has something to do with these commands: cd /tmp wget http://us.archive.ubuntu.com/ubuntu/pool/main/k/krb5/libkrb53_1.6.dfsg.4~beta1-5ubuntu2_i386.deb wget http://us.archive.ubuntu.com/ubuntu/pool/main/i/icu/libicu38_3.8-6ubuntu0.2_i386.deb sudo dpkg -i *.deb sudo echo "deb http://php53.dotdeb.org stable all" >> /etc/apt/sources.list sudo apt-get update sudo apt-get install php5-cli php5-common php5-suhosin sudo apt-get install php5-fpm php5-cgi The web-sites that are hosted from my server works fine. Anyone that have the same experience or know how this could happen? I guess that I have to re-install Ubuntu Server from my "control panel" now, but I would like to avoid this situation in the future. Finally, I have backup on everything so nothing is lost if I have to re-install the machine.

  Read the article

• Dante (SOCKS server) not working

  - by gregmac

  I'm trying to set up a SOCKS proxy using dante for testing purposes. However, I can't even get it to work with a web browser, after looking at several tutorials on how to do that. I've tried in both IE and Firefox, in both cases, using "Manual proxy configuration", leave everything blank except for SOCKS host, and then put in the IP of my proxy and the port number (1080). I just get "Server not found" / "Problems loading this page" and don't see anything in danted, even running in debug mode. If I do a "telnet 10.0.0.40 1080" I do see the connection open in danted debug output, so I know that much is working. Here's my config: logoutput: stdout /var/log/danted/danted.log internal: eth0 port = 1080 external: eth0 method: username none #rfc931 user.privileged: proxy user.notprivileged: nobody user.libwrap: nobody connecttimeout: 30 # on a lan, this should be enough if method is "none". client pass { from: 10.0.0.0/8 port 1-65535 to: 0.0.0.0/0 } client pass { from: 127.0.0.0/8 port 1-65535 to: 0.0.0.0/0 } client block { from: 0.0.0.0/0 to: 0.0.0.0/0 log: connect error } block { from: 0.0.0.0/0 to: 127.0.0.0/8 log: connect error } pass { from: 10.0.0.0/8 to: 0.0.0.0/0 protocol: tcp udp } pass { from: 127.0.0.0/8 to: 0.0.0.0/0 protocol: tcp udp } block { from: 0.0.0.0/0 to: 0.0.0.0/0 log: connect error } I'm sure I'm probably missing something simple, but I'm lost. I haven't even thought about SOCKS since the late 90's.

  Read the article

• Windows 7 - Windwos XP - sharing - why isn't working?

  - by durumdara

  Hi! This is seems to be "hardware" and not "software" / "programming" question, but I need to use this share in my programs, so it is "close to programming". We had an XP based wireless network. The server is XP Professional, the clients are XP Home (Notebooks). This was working well with folder sharing (with user rights, not simple share). Then we replaced the one of the notebook with Win7/X64 notebook. First time this can reach the server, and the another client too. Later I went to another sites, and connect to another servers, another networks. And then, when I return to this network, I saw that I cannot connect to this server. Nothing of resources I see, and when try to dbl click on this computer, I got login window, where I can write anything, never I can login... The interesting part, that: Another XP home can see the server, can login as quest, or with other user. The server can see the XP home notebook. The Win7 can see the notebook's shared folders, and XP home can see the Win7 shared folders. The server can see the Win7 folders, BUT: the Win7 cannot see the server folders. Cannot see the resources too... The Win7 is in "work networking group", the group name is not mshome. I tried everything on the server, I tried to remove MS client, restore it with simple sharing, set guest password, etc., but I lost the possibilities to access this server from Win7. Does anyone have any idea what I need to see, what I need to set to access these resource - to use them in my programs? Thanks for every info, link: dd

  Read the article

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• Abnormally high amount of Transmit discards reported by Solarwinds for multiple switches

  - by Jared

  I have several 3750X Cisco switches that, according to our Solarwinds NPM, are producing billions of transmit discards per day. I'm not sure why it's reporting these discards. Many of the ports on the 3750X's have 2960's connected to them and are hardcoded as trunk ports. Solarwinds NPM version 10.3 Cisco IOS version 12.2(58)SE2 Total output drops: 29139431: GigabitEthernet1/0/43 is up, line protocol is up (connected) Hardware is Gigabit Ethernet, address is XXXX (bia XXXX) Description: XXXX MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100/1000BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:47, output 00:00:50, output hang never Last clearing of "show interface" counters 1w4d Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 29139431 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 35000 bits/sec, 56 packets/sec 51376 packets input, 9967594 bytes, 0 no buffer Received 51376 broadcasts (51376 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 51376 multicast, 0 pause input 0 input packets with dribble condition detected 115672302 packets output, 8673778028 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out sh controllers gigabitEthernet 1/0/43 utilization: Receive Bandwidth Percentage Utilization : 0 Transmit Bandwidth Percentage Utilization : 0

  Read the article

• Deploying concrete5 on nginx

  - by Nithin

  I have a concrete5 site that works 'out of the box' in apache server. However I am having a lot of trouble running it in nginx. The following is the nginx configuration i am using: server { root /home/test/public; index index.php; access_log /home/test/logs/access.log; error_log /home/test/logs/error.log; location / { # First attempt to serve request as file, then # as directory, then fall back to index.html try_files $uri $uri/ index.php; # Uncomment to enable naxsi on this location # include /etc/nginx/naxsi.rules } # pass the PHP scripts to FastCGI server listening on unix socket # location ~ \.php($|/) { fastcgi_pass unix:/tmp/phpfpm.sock; fastcgi_split_path_info ^(.+\.php)(/.+)$; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param PATH_INFO $fastcgi_path_info; include fastcgi_params; } location ~ /\.ht { deny all; } } I am able to get the homepage but am having problem with the inner pages. The inner pages display an "Access denied". Possibly the rewrite is not working, in effect I think its querying and trying to execute php files directly instead of going through the concrete dispatcher. I am totally lost here. Thank you for your help, in advance.

  Read the article

• Gmail.com detect mail as spam, but the server is not on any BlackList

  - by Tomer W

  I have an issue with Google. (GMail to be exact) About 1 month ago, we had a security breach, and mail was relayed through our servers. we got listed in almost ALL Black-Lists :( we fixed the problem, and requested removal from Black-lists, which was granted easily. currently (over 3 weeks), we are not sending any spam anymore. furthermore, we got clear from all the Black-lists (MxToolBox Black-List Search Result) But, GMail still refuse to get Anything from the server, stating '550 Spam'. Following, Telnet attempt to send to gmail: 220 mx.google.com ESMTP g47si45436208eep.123 helo megatec.co.il 250 mx.google.com at your service mail from: <[email protected]> 250 2.1.0 OK g47si45436208eep.123 rcpt to: <[email protected]> 250 2.1.5 OK g47si45436208eep.123 Data 354 Go ahead g47si45436208eep.123 Test123 . 550-5.7.1 [62.219.123.33 11] Our system has detected that this message is 550-5.7.1 likely unsolicited mail. To reduce the amount of spam sent to Gmail, 550-5.7.1 this message has been blocked. Please visit 550-5.7.1 http://support.google.com/mail/bin/answer.py?hl=en&answer=188131 for 550 5.7.1 more information. g47si45436208eep.123 Connection to host lost. i tried filling the form @ Gmail - Report Delivery Problem i also tried reaching Google by phone, but the message was to go to the Link mentioned above. I Checked ReverseDNS and is ok... We dont have TLS, but that shouldn't be a problem, shouldn't it? Note: we are not a Bulk sender. Anyone has an idea? what can be blocking our IP? Anyone know whom can be contacted in order to resolve this BL listing?

  Read the article

• Fix for php 5.3.9 libxsl security "bug" fix

  - by Question Mark

  just this morning i updated my debian server to php 5.3.9 , change log (last item in list) has a fix for this bug and now when running any hosted site using XSL transforms i get: Warning: XSLTProcessor::transformToXml(): Can't set libxslt security properties, not doing transformation for security reasons I'm not using any <sax:output> tags in my xslt at all. Does anybody have any information on this, current chatter about it is thin, so i'm i little lost. Using the suggestion about switching ini settings on and off either side of -transformToXml(): ini_set("xsl.security_prefs", XSL_SECPREFS_NONE) or $xsl->setSecurityPreferences(XSL_SECPREFS_NONE) brings me back to the same error Many thanks. Progress: - Upgrading libxml and recompiling libxslt against the new version was a good suggestion, though has not fixed the issue. - Compiling the latest php5.3 snapshot does not fix the issue. Solution: I'm unsure what actually solved this, very sorry for anyone else having the same problem. firstly i upgraded libxml, then applied a few patches, then went into php source for the xsl parser and added some debugging and a few tweaks, after a few compiles getting the configure args right the error went away and wasn't reproducible. I would definitely recommend upgrading libxml as Petr suggested below and then grabbing the latest snapshot from php.net.

  Read the article

• Spots appear in a rectangle area on screen, ubuntu gnome 13.04, nvidia driver

  - by frozen-flame

  I am using Ubuntu Gnome 13.04 with nvidia-310 driver installed. My GPU is GeForce GTX650. Strange spots freqently appear on screen, with following traits: Spots are restricted in one or two rectangle areas at any instant. When typing, the pattern of spots change. Possibly increase, or all disappear when one key pressed. Mouse movement also influences. This problem last within one boot. The only way can I get rid of this problem is to reboot. It can be detected as soon as entering desktop if it appears. Simultaneously, the "power off" option is lost in the top-right menu of Gnome3. Never such problem when using windows 7 on the same computer, neither ubuntu with Nouveou driver. Seldomly, half of the screen become black. I googled a lot. Similar conditions are described, but no confirmed solution. Uninstall-r einstall strategy does not work. Any clue solving this will be appeciated.

  Read the article

• svnsync loses revision properties although hook installed

  - by roesslerj

  Hello all! I have a pretty weird problem. We have setup an SVN-Mirror via cronjob (because it needs to go from inside to outside of a firewall, so no post-commit-hook possible) and svnsync. We installed a pre-revprop-hook just as told. Everything seems to work fine, except that it doesn't. E.g. when manually executing the script. # svnsync --non-interactive sync file://<path-to-mirror> --source-username <usr> --source-password <pwd> Committed revision 19817. Copied properties for revision 19817. No error, no complaints. But if checking for the revision properties it says: # svnlook info <path-to-mirror> 0 # svn info -r HEAD file://<path-to-mirror> 2>&1 Path: <root-of-mirror> URL: file://<path-to-mirror> Repository Root: file://<path-to-mirror> Repository UUID: <uid> Revision: 19817 Node Kind: directory Last Changed Rev: 19817 So somehow the author and timestamp information gets lost. But we need that information for our internal processes. Since no error or warning is produced I have absolutely no idea even where to start to look. Everything is local (except for the remote master), so there are no server-logs to look at. I also tried to manually recopy via svnsync copy-revprops (http://chestofbooks.com/computers/revision-control/subversion-svn/svnsync-Copy-revprops-Ref-svnsync-C-Copy-revprops.html). It says Copied properties for revision 19885. But when I query them, it's just the same. Any ideas how I could approach that problem, or even better -- how to solve it? Any ideas appreciated.

  Read the article

• Excel 2010 data validation warning (compatibility mode)

  - by Madmanguruman

  We have some legacy worksheets that were created in Excel 2003, which are used by LabVIEW-based test automation software. The current LabVIEW software can only handle the legacy .xls format, so we're forced to keep these worksheets as-is for the time being. We've migrated to Office 2010 and when working with these worksheets, I see this warning: "The following features in this workbook are not supported by earlier versions of Excel. These features may be lost or degraded when you save this workbook in the currently selected file format. Click Continue to save the workbook anyway. To keep all of your features, click Cancel and then save the file in one of the new file formats." "Significant loss of functionality" "One or more cells in this workbook contain data validation rules which refer to values on other worksheets. These data validation rules will not be saved." When I click 'Find', some cells that do indeed have validation rules are highlighted, but those rules are all on the same worksheet! We're using simple list-based validation, with some cells off to the side containing the valid values (for example, cell B4 has a List with Source "=$D$4:$E$4") This makes no sense to me whatsoever. One, the workbook was created in Excel 2003, so obviously we couldn't implement a feature that doesn't exist. Secondly, the modifications we're making don't involve changing the validation rules at all. Thirdly, the complaint that Excel is making is incorrect! All of the rules are on the same worksheet as the target. As if the story wasn't bizarre enough: I went ahead and saved the worksheet with Excel 2010. I then went to an old computer back in the lab and opened the document with Excel 2003. Guess what - the validations were untouched! My questions are: is this a legitimate bug in Excel 2010, or is this some exotic error in the legacy .xls worksheet that is confusing the heck out of Excel 2010? Has anyone else observed this issue working in compatibility mode?

  Read the article

• postfix smtpd rejecting mail from outside network match_list_match: no match

  - by Loopo

  My postfix (V: 2.5.5-1.1) running on ubuntu server (9.04) started to reject mail arriving in from outside about 2 weeks ago. Doing a "manual" session via telnet shows that the connection is always closed after the MAIL FROM: [email protected] line is input, with the message "Connection closed by foreign host." Doing the same from another client inside the LAN works fine. In the log files I get the line "lost connection after MAIL from xxxxx.tld[xxx.xxx.xxx.xxx]" This is after some lines like: match_hostaddr: XXX.XXX.XXX.XXX ~? [::1]/128 match_hostname: XXXX.tld ~? 192.168.1.0/24 ... match_list_match: xxx.xxx.xxx.xxx: no match which seem to suggest some kind of filter which checks for allowed addresses. I have been unable to locate where this filter lives, or how to turn it off. I'm not even sure if that's what's causing my problem. Connections from inside the LAN don't get disconnected even though they also show a "match_list_match: ... no match" line. I didn't change any configuration files recently, below is my main.cf as it currently stands. I don't really know what all the parameters do and how they interact. I just set it up initially and it worked fine (up to recently). smtpd_banner = $myhostname ESMTP $mail_name (GNU) biff = no readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/server.crt smtpd_tls_key_file=/etc/ssl/private/server.key #smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtp_sasl_auth_enable = no smtp_use_tls=no smtp_sasl_password_maps = hash:/etc/postfix/smtp_auth myhostname = XXXXXXX.com alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = XXXX.XXXX.com, XXXX.com, localhost.XXXXX.com, localhost relayhost = XXX.XXX.XXX.XXX mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 192.168.1.0/24 mailbox_command = procmail -a "$EXTENSION" mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all smtpd_sasl_local_domain = #smtpd_sasl_auth_enable = yes smtpd_sasl_security_options = noanonymous smtpd_sasl_authenticated_header = yes broken_sasl_auth_clients = yes smtpd_recipient_restrictions = permit_mynetworks,permit_sasl_authenticated,reject_unauth_ when checking the process list, postfix/smtpd runs as smtpd -n smtp -t inet -u -c -o stress -v -v Any clues?

  Read the article

• Cannot click send button in Outlook (+ Exchange) for unknown addresses

  - by Graphain

  Hi, I have a very unusual problem. I have Outlook 2010 connected to Exchange 2010. This can send emails perfectly to known addresses (that is, addresses in the address book or ones that have been sent to previously). However, if I put in an address that is unknown, I cannot actually click the Send button in Outlook. (it simply does nothing). Corresponding to this I get errors in the Event Log for each Send click stating "The connection to Microsoft Exchange is unavailable. Outlook must be online or connected to complete this action.". However, Outlook shows as connected the whole time, pings do not break, and I have no reason to suspect it has lost connection. To further complicate matters, Outlook is fine on all other PCs, and this was all perfect until I installed BitDefender on the PC in question and the Exchange Server. Outlook was still fine on these other PCs while BitDefender was installed, but I have removed it from the PC in question and the Server just in case (no success). Summary: Outlook encounters Exchange connectivity issues when sending to unknown (new) email addresses that prevent the Send button actually working at all. This is isolated to one machine and occurred after installation of AV/Firewall software which has since been thoroughly removed. If you have any potential solutions I'd love to hear them, as I will be resorting to reformatting the PC in question, and probably removing Exchange because I'm sick of its issues if I cannot resolve this soon. Big thanks for any help.

  Read the article

• Losing JSESSIONID when using ProxyHTMLURLMap

  - by Matthew Schmitt

  I've setup a reverse proxy between an Apache front-end and multiple Tomcat backends. The below block of code includes the ProxyHTMLURLMap param so that the HTML can be rewritten to remove the Tomcat context path. With this setup in place, after logging into my application, an initial JSESSIONID is set properly, but when navigating to any other page, this JSESSIONID is lost and another one is set by the application. I should mention that the initial login directs to a URL that includes the current context path (i.e. https://app.domain.com/context/home), but when navigating to another page, that context path is not present in the URL (i.e. https://app.domain.com/page2). <Proxy balancer://happcluster> BalancerMember ajp://happ01.h.s.com:8009 route=worker1 loadfactor=10 timeout=15 retry=5 BalancerMember ajp://happ02.h.s.com:8009 route=worker2 loadfactor=10 timeout=15 retry=5 BalancerMember ajp://happ03.h.s.com:8009 route=worker3 loadfactor=5 timeout=15 retry=5 BalancerMember ajp://happ04.h.s.com:8009 route=worker4 loadfactor=5 timeout=15 retry=5 BalancerMember ajp://happ05.h.s.com:8009 route=worker5 loadfactor=5 timeout=15 retry=5 ProxySet lbmethod=bytraffic ProxySet stickysession=JSESSIONID </Proxy> ProxyPass /context balancer://happcluster/context ProxyPass / balancer://happcluster/context/ <Location /context/> # Rewrite HTTP headers and HTML/CSS links for everything else ProxyPassReverse / ProxyPassReverseCookieDomain / app.domain.com ProxyPassReverseCookiePath / /context ProxyHTMLURLMap /context/ / # Be prepared to rewrite the HTML/CSS files as they come back # from Tomcat SetOutputFilter INFLATE;proxy-html;DEFLATE </Location> Has anyone ever run into a similar situation?

  Read the article

• Unix Permissions: Enable access to files no matter the user?

  - by TK Kocheran

  I've been using Linux for a long time and I still am completely in the dark about how file permissions really work. With that in mind, does anyone have any books or thorough guides I could read to really understand things completely? I've done my fair share of sysadminning, so I know the easy stuff like making directories readable and writable, making files executable, and changing the owner of a file, but on sharing files across users, I'm lost. Here's my main problem. I have a number of machines across which I intend to synchronize my music library. I've been using Unison for a while now and it's a great choice as I can easily run it over SSH on my local network which I just set up. Win-win. Up until this point, I've been synchronizing computers using a 2TB external hard drive. (computer 1 unisons to HD, computer 2 unisons to HD, etc.) This is tedious at best, especially since I encrypted the drive, making it a huge hassle to hook it up to all of my machines and sync it. Anyway, the drive is running ext4 (in TrueCrypt), so it maintains all Unix filesystem info like owners and groups. I just set up a new machine and just Unison'd it to get the music on it, and I realized that now, all of my permissions are fubar. I had to run Unison as root since that was the only way I could get the files to come off of the external drive. Apparently, since I'm using a different user name on this machine than my usual "rfkrocktk" across all machines, this essentially throws a huge wrench in the gears. Here's my use case. This laptop has two effective users, "leandra" and "rfkrocktk". I want to share music between these two users, so I symlinked /home/rfkrocktk/Music to point to /home/leandra/Music. How do I (a) allow both users access to read/write/delete files in this folder, and (b) keep everything nicely in sync without messing up file ownership?

  Read the article

• Error when starting qpidd as a service

  - by Sparks

  I have recently swapped from CENTOS 5 to FEDORA 17. Previously I have created my own init.d scripts successfully (albeit not for qpidd) however, in FEDORA I cannot get it to work. I have created the following script (called qpidd) in the init.d directory: #!/bin/bash # # /etc/rc.d/init.d/qpidd # # QPID/AMQP Broker scripts # # # chkconfig: 2345 20 80 # description: QPID/AMQP Broker service # processname: qpidd # pidfile: /var/lock/subsys/qpidd # Source function library. . /etc/init.d/functions SERVICENAME=qpidd start() { echo -n "Starting $SERVICENAME: " daemon qpidd -d & retval=$? touch /var/lock/subsys/$SERVICENAME return $retval } stop() { echo -n "Shutting down $SERVICENAME: " qpidd -q & retval=$? rm -f /var/lock/subsys/$SERVICENAME return $retval } case "$1" in start) start ;; stop) stop ;; status) status qpidd ;; restart) stop start ;; condrestart) [ -f /var/lock/subsys/<service> ] && restart || : ;; *) echo "Usage: $SERVICENAME {start|stop|status|restart" exit 1 ;; esac exit $? After this, I ran chkconfig --add qpidd, however, now when I run sudo service qpidd start I get the following message: Starting qpidd (via systemctl): Job failed. See system journal and 'systemctl status' for details. If I then run systemctl status qpidd I get the following message: Failed to issue method call: Unit name qpidd is not valid. I am now lost, I have search the web and Stack Overflow but cannot find anybody with similar problem, any help or direction to a website that can help would be much appreciated Sparks :)

  Read the article

• Dynamic ARP Entries turning into Static ARP entries

  - by Zach

  I recently acquired a client that has a strange ARP caching issue on one of thier servers. I have a server that will eventually start turning it's dynamic ARP entries into static ARP entries. This causes problems because when the machine that has a static ARP entries on this server receives a new IP via DHCP, then the server is not able to communicate with the clients. Clearing the ARP cache resolves the issue and the server is fine for about a week and then it starts slowly turning ARP entries into static ARP entries. I haven't narrowed it down to when or how many it starts to do, but slowly you start seeing 1 static ARP and then 5 and then 10. The server in question is a Windows Server 2003 SP2. It is a DC, DHCP, and DNS server. I've checked the DHCP scope options and there's nothing in there that would indicate anything to do with static ARP entries. The only thing different between this DNS server and our other DNS server is that the 'Dynamically Update DNA A and PTR records for DHCP clients that do not request updates' is checked on the problematic server. I've done a bit of research about this and it seems that this may happen if any PXE type services are running, from what I can tell, there is nothing running a PXE server. I'm a bit lost as I have never seen dynamic ARP entries start to turn into static ARP entries. Right now my solution is a schedule task that runs every 24 hours to clear the ARP cache (arp -d *). I would like to not rely on this schedule task. Has anybody seen this before or have any suggestions on how to troubleshoot this?

  Read the article

• Configure PEAR on CentOS 6 and PLESK

  - by RCNeil

  I'm hoping to get a little assistance with configuring PEAR to work properly. I have a PHP file that's calling PEAR's mail and mail-mime files, and I believe I am missing some steps because I keep getting the very common Warning: include_once(Mail.php): failed to open stream: No such file or directory Warning: include_once(Mail_Mime/mime.php): failed to open stream: No such file or directory It is installed - Installed packages, channel pear.php.net: ========================================= Package Version State Archive_Tar 1.3.7 stable Console_Getopt 1.2.3 stable Mail 1.2.0 stable Mail_Mime 1.8.3 stable PEAR 1.9.4 stable Structures_Graph 1.0.4 stable XML_RPC 1.5.4 stable XML_Util 1.2.1 stable And according to this TUT, I need to configure it appropriately in each vhost. I have already gone through and adjusted the php.ini file, but when the TUT speaks of the php_admin_value open_basedir "/var/www/vhosts/example.com/httpdocs:/tmp:/usr/share/pear:/local/PEAR" in my /var/www/vhosts/example.com/conf/httpd.include file I kind of get lost. There are several httpd.include files in that directory, all preceded with very long numerical strings. All I want to do is have an email attachment in my form.... Any insight or similar experiences shared would be greatly appreciated.

  Read the article

• PHP Script Won't Run - Apache2/MySQL Servers Running, PHP Installed - Ubuntu 10.04

  - by nicorellius

  I am trying to install a CRM on a Linux (Ubuntu 10.04) laptop to do some testing. Installing the current versions of Apache, MySQL and PHP, and getting the CRM to run is easy. It's when I try to go backwards and run it on a previous set of versions I run into problems. This is what I have done: I have installed Apache 2.2.14, MySQL 5.0.83, and PHP 5.2.8. When I type something like mysql --version I get back what I would expect: version and distribution info. The same goes for Apache2 and PHP. The Apache server is running and so is mysqld. So when I go to my browser and look at http://localhost/<CRM dir>/install.php Firefox offers to open the PHP file or save it, as if it doesn't recognize the file. What should happen is that I should get a welcome page and the installation wizard for this CRM distribution should start. I have tried so many different things I probably screwed up something along the way. I have restarted the servers over and over, and even recompiled the versions of MySQL and PHP with no problems. I am hoping I am overlooking something simple because I am lost. Any help is appreciated.

  Read the article

< Previous Page | 109 110 111 112 113 114 115 116 117 118 119 120  | Next Page >