Search Results

Search found 4161 results on 167 pages for 'desmond lost'.

Page 118/167 | < Previous Page | 114 115 116 117 118 119 120 121 122 123 124 125  | Next Page >

• Alfa AWUSO36H 1W dysfunctional driver

  - by BrainStorm

  I recently purchased an Alfa AWUSO36H 1W wireless USB adapter for my notebook, in order to improve signal strength and quality. I'm currently using Linux Mint 11, and the it uses the RTL8187 driver for this adapter, I'm also using a 4dbi antenna, though I have others. The problem is that this adapter does exactly the opposite of what it should, actually my internal Broadcom BCM4313 adapter works way better than the alfa. Browsing is slow, some network applications don't even work, pings against Google.com on the internal adapter runs smooth, while in the alfa it gets like 25% packets lost or more! I'm less them 50 feet from my AP, the internal adapter gets 44/70 link quality, and the alfa gets around 60/70 (iwconfig output). Also the system always sets alfa power to 20dbm(100mw), then I have to do sudo iw set reg B0 to make it 30dbm(1000mw), but apparently no significant change. I've installed wireless-compat drivers, no change either. And worst of all, in Windows 7 it works way more smoothly for browsing, though I couldn't test it properly there. I hope its a driver problem, even if it's a pain to find/compile Linux drivers for a starter, I prefer it to a hardware problem where I would need to buy another adapter, since I have no money left (except for the cantenna pieces).

  Read the article

• Change default profile directory per group

  - by Joel Coel

  Is it possible to force windows to create profiles for members of one active directory group in a different folder from members in another active directory group? The school here uses DeepFreeze to protect public computers. In a nutshell, DeepFreeze prevents all changes to a hard drive such that every time you restart the machine the disk is identical to it was at the time you froze it. This is a bit different than restoring to an image, in that it never really wrote changes to disk in a permanent way in the first place. This has a few advantages over images: faster recover times, and it's easy to thaw the machine for a few minutes to perform maintenance such as windows updates (which can even be automated). DeepFreeze also allows you to configure a "thawspace" partition, where changes are persistent across reboots. One of the weaknesses of DeepFreeze is that you end up needing to create a new profile every time you log in, unless your profile existed at the time the machine was frozen. And even then, any changes you make to your profile while working on a frozen machine are lost. As students have frequent legitimate needs to log in to our classroom machines, there is currently a lot of cleanup involved from time to time in removing their old profiles and changes, so I want to extend DeepFreeze to protect our classroom computers as well as public computers. The problem is that faculty have a real need to keep a stateful profile locally on these classroom computers. The solution I would like to use is to configure Windows via group policy (or even manually, if that's the way I'll have to do it) to place profile folders on the thawspace partition, but only for members of the faculty security group. Is this possible?

  Read the article

• few basic questions on webhosting (namservers & dns records)

  - by claws

  I bought a domain name on name.com & I want to use free webhosting on 110mb.com By default name.com integrates services of Google apps. Name server entries are ns1.name.com ns2.name.com ns3.name.com ns4.name.com When I registered on 110mb.com it gave me two addresses ns1.110mb.com ns2.110mb.com This is where I'm lost. The concept is that "Domain name should point to an address of the server where the website is hosted" right? Then why are these 4 entires by default. How exactly is it working? should I remove these 4 and then add 110mb.com servers or just append 110mb.com server addresses to name.com ones. I would like to use google apps. If I change these name server addresses would that remove google apps? I especially want to use email service of google. And I really don't understand what is CNAME, MX, or something something. I want to learn about these stuff & how it exactly works. When I search for webhost tutorial. I'm unable to find any fruitful results.

  Read the article

• IP6 seems to be enabled - How do I configure it without interfering with IP4?

  - by Mister IT Guru

  I noticed that some of my Centos boxes have IP6 enabled, and seem to have addresses. I have no problem with this, but I would like to get a handle on it, and even connect to them using IP6. This would really help if for any reason DHCP has a hiccup. But I'm a bit lost as to where the configuration on my CentOS box is. (I am also on google researching this, but I like server fault! :) ) I am hoping that I would be able to log into this via the VPN because every now and then that DHCP device has a bad morning, and needs to be restarted. (I'm also looking into this issue, but someone else handles that, management separation gone mad!) It's a remote client, so it would be a lot easier for me to connect to these systems which seem to self configure, to use that as a pivot via ssh tunnels to get to other remote devices to continue to manage them, while out main route is fixed. I guess, my questions are How can I configure IP6 without interfering with IP4, and On CentOS, can I influence this auto configuration I seem to be seeing?

  Read the article

• Internet Explorer / Windows 7 does not want to show HTML file from local network drive

  - by Jaanus

  Setup: I have Windows 7 running inside VirtualBox on Mac OS X host. I have a shared drive with some HTML files, that I am mounting as a local drive W: in Windows, from the VirtualBox server \VBOXSVR. I want to look at them with a browser in Windows. Chrome in Windows 7 opens and shows those HTML files just fine (file:///W:/welcome.html). But Internet Explorer does not, and shows this error instead of the files: Internet Explorer cannot display the web page What you can try: [button Diagnose Connection Problems] More information This problem can be caused by a variety of issues, including: Internet connectivity has been lost. The website is temporarily unavailable. The Domain Name Server (DNS) is not reachable. The Domain Name Server (DNS) does not have a listing for the website's domain. If this is an HTTPS (secure) address, click Tools, click Internet Options, click Advanced, and check to be sure the SSL and TLS protocols are enabled under the security section. For the internet zone in the status bar, it shows: Internet | Protected Mode: On IE settings are a mystery to me, and I could possibly get it to work by tweaking IE settings, but I don't know which ones. How do I make IE show the same files that Chrome is happy to show? (Chrome showing them means that the files themselves are fine, there is something about the setup that just makes IE be a diva.)

  Read the article

• Servers / ram for social network- how many?

  - by Marty

  I am launching my social network soon an looking into hosting. The question i am lost is: Do i need separate servers for web vs database vs image handling since there is photo sharing? Or does 1 server handle it all? Also is more ram better? If i get 50GB ram is that better than having 8 gb ram? EDIT: It is PHP codeignitor and MySQL for now. (switch to NoSQL DB later if demand calls fr it.) I will be using memcache also. Concept wise it is similar to yelp, so geographic based with lots of user content and image sharing + live feeds an privacy levels. User plan is open question. Without testing the demand for this i cant give a number. But the concept is unique, no one out there with the set of features i am releasing so it could grow. Ideally I want to plan for handling about 1-2 million views / month from launch. If it goes more than that then I will upgrade.

  Read the article

• Deploying a Django application in a virtual Ubuntu Server

  - by mfsaint

  I have a virtualbox machine running Ubuntu Server 10.04LTS. My intention is to this machine to work like a VPS, this way I can learn and prepare for when I get a VPS service. Apache+mod_wsgi for deploying the Django app seems the right choice to me. I have the domain (marianofalcon.com.ar) but nothing else, no DNS. The problem is that I'm pretty lost with all the deployment stuff. I know how to configure mod_wsgi(with the django.wsgi file) and apache(creating a VirtualHost). Something is missing and I don't know what it is. I think that I lack networking skills ant that's the big problem. Trying to host the app on a virtualbox adds some difficulty because I don't know well what IP to use. This is what I've got: file placed at: /etc/apache2/sites-available: NameVirtualHost *:80 <VirtualHost *:80> ServerAdmin [email protected] ServerName www.my-domain.com ServerAlias my-domain.com Alias /media /path/to/my/project/media DocumentRoot /path/to/my/project WSGIScriptAlias / /path/to/your/project/apache/django.wsgi ErrorLog /var/log/apache2/error.log LogLevel warn CustomLog /var/log/apache2/access.log combined </VirtualHost> django.wsgi file: import os, sys wsgi_dir = os.path.abspath(os.path.dirname(__file__)) project_dir = os.path.dirname(wsgi_dir) sys.path.append(project_dir) project_settings = os.path.join(project_dir,'settings') os.environ['DJANGO_SETTINGS_MODULE'] = 'myproject.settings' import django.core.handlers.wsgi application = django.core.handlers.wsgi.WSGIHandler()

  Read the article

• Autounmounting USB keys with FAT filesystem on Linux (RHEL5)

  - by niXar

  For security reasons, I have two workstations i front of me, and I can only transfer data between them through a USB key. As you can imagine, it can get quickly tiresome, but the most annoying is having to unmount the things before removing them. Not umounting them results in missing files most of the time, even if I remove them a while after having last written to them. Now, since they're only used for transferring smallish files, and each are basically written once and read once, I don't need the fancy pansy caching infrastructure that makes clean unmounting a necessary step. And since the data is always a copy of something I have at hand, I don't care if the filesystem croaks from time to time. But anyway the system doesn't need to force that on me, it could simply make sure everything is committed with a second, and works synchronously. Then when I remove the key, nothing is lost. Is there a way to do this? I would appreciate any other tips on handling this situation. Edit: it appears the situation has changed between RHEL5 and Fedora up to F11 on one hand, and F12 on the other. The latter use DeviceKit-disk, and I haven't quite figured out how to do this. The method provided below in gconf does not work anymore.

  Read the article

• SQL Server Installation: Is it 32 or 64 bit?

  - by CapBBeard

  Hi, Recently I was performing an OS upgrade on one of our DB servers, moving from Server 2003 to Server 2008. The DBMS is SQL Server 2005. While reinstalling SQL on the new Windows installation, I went to another of our DB servers to verify a couple of settings. Now, I always thought this second server was Server 2003 x64 + SQL 2005 x64 (from what I'd been told), but I now have my doubts about this. I now suspect that it is in fact only 32 bit SQL, however I'd like to verify this. Here's some details: The OS is definitely 64 bit. xp_msver shows Platform as NT INTEL X86 SELECT @@VERSION shows Microsoft SQL Server 2005 - 9.00.4035.00 (Intel X86)... However sqlservr.exe is not shown with '* 32' in taskmgr, does anyone know why this is the case, if it is in fact 32 bit as claimed? Despite this, it does seem to be running out of the x86 program files folder. If I do the same checks on a confirmed 64 bit installation, it does give back the expected 64 bit readings, which can only prove that this server in question is only running in 32 bit. Now, that being the case, the question arises about how much memory this '32 bit' install can use. Task manager reports about 3.5GB memory usage for sqlservr.exe (The server has 16GB physical). I suspect that AWE has not been configured at all, and therefore the server will be significantly under-utilised (remembering that the OS is 64 bit) if SQL is simply using a 32bit address space. Is this assumption correct? I feel the server should have SQL reinstalled as 64 bit in order to fully utilise the hardware platform, however it is currently heavily in production; this will be no easy task. I suspect we may just have to configure AWE correctly and let it be for the time being (Unless this is a bad idea?). I apologise that this question is a little vague/lost; I'm no SQL expert, just trying to get a handle on what's going on here.

  Read the article

• I deployed Flash Player via a Software Installation policy. How to upgrade?

  - by eleven81

  I have a Windows Server 2008 machine as my DC. Earlier this year I created a Software Installation GPO to deploy Adobe Flash Player plugin MSI. I assigned the policy to the computers, about half run Windows XP x86 and the other half Windows 7 x64. That all works like clockwork. When I created the Software Installation Policy, I disabled the Flash Player plugin's automatic update feature by editing the MSI in Orca. I did this because I wanted all of my machines to run the exact same version of the plugin. Now, some time has passed and a newer version of the Flash Player plugin has been released. It is time for me to push out the updated version of the plugin. I already have the new MSI, but I am lost on what to do next. I see the upgrades tab in the Software Installation GPO, but everything there reads like that would be used for add-ons to a larger master program and not for updates that are released over time. I have read that it is best to create a new Software Installation policy with the new MSI, revoke the old GPO, and assign the new GPO. I feel as though, over time, I will wind up with more revoked policies than active ones. I have also read that some people have had success by replacing the old MSI with the new MSI and simply telling the GPO to redeploy. This seems like a backdoor method that will only get me in to trouble. In short, what is the correct, best-practice, or preferred way to roll out the new version via Group Policy?

  Read the article

• BIOS not detecting working SATA hard drive

  - by user28927

  Some time ago my power supply died. It's a long story from then till now, but the important bit is that I ended up with a new hard drive and a new power supply. I tested to see if my original hard drive was still alive, and it booted and worked perfectly until I turned it off. When I started it again it would not boot. I bought new SATA cables, assuming that the one I had was not seating properly (it was cheap and wobbly), but no dice. Upon start-up I am presented with a message telling me to insert boot media into the selected drive or add a drive and restart. Neither the new or the old drive is detected by BIOS, my Vista install disk, or from my bootable Linux USB drive. When I remove all of the RAM the computer ceases outputting visual information, and upon reinstalling the ram and starting up again gives me a "failed overclock" error. So, does anyone have an idea as to what might be going on? I'm completely lost at this point.

  Read the article

• Failover Cluster Quorum Failing

  - by oruchreis

  Hi, I have two nodes which boots from iscsi to implement windows 2008 cluster. And I'm using disk majority option as quorum over iscsi. But when the quorum's iscsi connection failed(May be san server reset), the failover cluster is failed too. If I reset one of the nodes, it can open, but its system disk goes offline. I cant change its status as online, because it says that its reserved by failover cluster(disk is on iscsi, beacuse iscsi boot). And this disk works as readonly. Anything on it cant be deleted or written. So, I cant rejoin the node to the cluster again. I have to reinstall windows. So, what I'm asking is, how can I implement more quorum backup? I mean, can I use both disk majority and file share majority at same time? AFAIK, every nodes also keep the quorum's copy too. But I don't know sometimes san servers goes offline. And quorum's iscsi connection and nodes' iscsi connections get lost. So, nor the quorum that is kept in the nodes neither the quorum iscsi disk is not enough to start the cluster again. I want to use both disk majority and file share majority at the same time. Can I do this? Have you any other suggestion? Regards.

  Read the article

• MySQL Not Turning On

  - by Shalin Shah

  I have an amazon ec2 instance running on the Amazon Linux AMI and its a micro instance. I wanted to install Django onto my server so I entered these commands wget http://www.mlsite.net/blog/wp-content/uploads/2008/11/go wget http://www.mlsite.net/blog/wp-content/uploads/2008/11/django.conf chmod 744 go ./go So after I was done, I ran sudo service httpd restart and sudo service mysqld restart and This is what came up for mysqld: Stopping mysqld: [ OK ] MySQL Daemon failed to start. Starting mysqld: [FAILED] So I deleted the django files /usr/local/python2.6.8/site-packages/django_registration.egg and I tried finding the error and I found out that in my /etc/my.cnf for the socket, it said socket=/var/lock/subsys/mysql.sock so I went to /var/lock/subsys/ and there was no mysql.sock. I tried creating one using vim but it still didn't work. Then I checked the error log and it said Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (2) So I am pretty much lost right now. I know it has something to do with mysql.sock If you might know a reason why this was caused could you please let me know? I have a wordpress site on my server, so i kind of need MySQL to work. Thanks!

  Read the article

• Strange network connectivity problem

  - by Marc

  Here is my network connectivity: cable modem | |(WAN) wrt54g (default gateway, 192.168.1.1) -- earth |(LAN) | Simple Switch1 | | | | | SimpleSwitch2- neptune | | | | mars mercury | |- venus | |- laptop | saturn (Windows AD DC) simpleSwitch2 was hanging off the wrt54g. I moved it to SW1 during troubleshooting. Nothing described below was any different. earth is connected via wireless to the wrt54g. I can ping from laptop to mars, neptune & mercury. I can ping from earth to venus, saturn & laptop. However, pinging mars, mercury or neptune from earth gives the following result. Pinging mars.XXX.XXX [192.168.1.105] with 32 bytes of data: Reply from 192.168.1.122: Destination host unreachable. Reply from 192.168.1.122: Destination host unreachable. Reply from 192.168.1.122: Destination host unreachable. Reply from 192.168.1.122: Destination host unreachable. Ping statistics for 192.168.1.105: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), .122 is the address of the machine from which I am pinging. earth is a Vista machine. Windows firewall is off. saturn is my DNS & DHCP server. Can anyone give me any ideas what the h*ll is going on? Clearly the topology is a factor And yes, I am a space geek.

  Read the article

• Using Samba to share a folder from a Linux guest with a Windows host in VirtualBox

  - by AmV

  I would like to share a folder from a Linux Guest with a Windows host (with read and write access if possible) in VirtualBox. I read in these two links: here and here that it's possible to do this using Samba, but I am a little bit lost and I need more information on how to proceed. So far, I managed to set up two network adapters (one NAT and one host-only) and install Samba on the Linux guest, but now I have the following questions: What do I need to type in samba.conf to share a folder from the Linux guest? (the tutorial provided in one of the links above only explains how to share home directories) Are there any Samba commands that need to be executed on the guest to enable sharing? How do I make sure that these folders are only available to the host OS and not on the Internet? Once the Linux guest is setup, how do I access each of the individual shared folders from the Windows host? I read that I need to mount a drive on Windows to do this, but do I use Samba logins, or Linux logins, also do I use localhost? or do I need to set up an IP for this? Thanks!

  Read the article

• Active Directory: how to be SURE users can change their own passwords?

  - by Latro

  Working on some project where a tool we have has to authenticate against AD connecting via LDAPS and perform password changes if required or requested. IN THEORY, the tool does that, and we have seen it work in other projects. IN PRACTICE, against this particular directory, it fails. Been driving me crazy. The particulars of the situation: Windows 2003 AD Defined a "technical user" for the LDAP connection with rights to change users passwords When password change is required - in this case, because pwdLastSet is 0 - the tool uses the technical account to go, bind to the controller and change the user password. If password change is not required but the user request it, then the bind is done with the user account. That last condition is the one that doesnt work. With the technical user the password change is possible, but with the user itself, it isnt. We get an error like this: LDAP access failed: javax.naming.directory.InvalidAttributeValueException: [LDAP: error code 19 - 0000052D: AtrErr: DSID-03190F00, #1: 0: 0000052D: DSID-03190F00, problem 1005 (CONSTRAINT_ATT_TYPE), data 0, Att 9005a (unicodePwd) no idea what DSID-03190F00 means cause it doesnt seem to be anywhere in google :-/ Been looking at several MS documentation pages and frankly, I'm not understanding one bit of it. There is some "control access right" called User-Change-Password that may, or may not, control what objects have the right to change their own password, which may, or may not, have to do with ACE and ACLs... There is GPO. There is maybe the password policy but it is only set to ask for passwords of 6 chars or more... Can anybody explain to me in easy-to-check steps how can I go and tell the AD admin guy (who is as lost as me) what to do to ensure that users in the AD directory (objectClass top,person,organizationalPerson and user) are able to change their own passwords by themselves? Thanks in advance

  Read the article

• Intermittent FTP login issues (Microsoft IIS FTP Service)

  - by JaggenSWE

  I've got a somewhat weird problem which I'm not sure how to troubleshoot. We have a FTP running on a Windows Server 2003 machine using the IIS FTP Service, this is for our clients and is configured with IP-restrictions. However, now ONE of the clients starts complaining that they can't log in to the server from time to time. This is just ONE of 10+ clients that have this issue, which makes me think it's a problem on their side. Just to be on the safe side I had a peek into the FTP logs and found something strange. Whenever succeed in loggin in this is what I can find in the logs: nnn.nnn.nnn.70, userxxx, 2012-06-11, 09:22:32, MSFTPSVC1, SERVERNAME, nnn.nn.nn.11, 0, 0, 0, 331, 0, [191747]USER, userxxx, -, nnn.nnn.nnn.70, userxxx, 2012-06-11, 09:22:32, MSFTPSVC1, SERVERNAME, nnn.nn.nn.11, 0, 0, 0, 230, 0, [191747]PASS, -, -, However, if the login fails I see the following events: nnn.nnn.nnn.70, userxxx, 2012-06-11, 09:16:33, MSFTPSVC1, SERVERNAME, nnn.nn.nn.11, 0, 0, 0, 331, 0, [191739]USER, userxxx, -, nnn.nnn.nnn.70, -, 2012-06-11, 09:16:33, MSFTPSVC1, SERVERNAME, nnn.nn.nn.11, 0, 0, 0, 530, 1326, [191739]PASS, -, -, When you look at the event where the clients sends the PASS in the successful login it seems to know that it is infact "userxxx" that is coupled to that PASS, but when it fails it seems to be lost since user in the PASS event is set to "-". Anyone have any ideas around this, any help would be appreciated. :) //JaggenSWE

  Read the article

• Moving a site from IIs6 to IIS7.5

  - by Sukotto

  I need to move a site off of IIS6 (Win Server 2003) and onto IIS7.5 (Win Server 2008) as soon as possible. Preferably tomorrow. The site itself is a delightful mix of classic asp (vbscript) and one-off asp.net (C#) applications (each asp.net app is in its own virtual dir and has a self-contained web.config). In case it's relevant, this is a sort of research site made up of 40 or 50 unconnected microsites. Each microsite is typically a simple form allowing a user to submit a form, which then runs a Stored Proc on a sqlserver db and displays a chart and/or table of the results. There is very little security to worry about. The database connection info is in a central file (in the case of the classic asp) or app's individual web.config (lots of duplication there) To add a little spice to the exercise... I have no idea how to admin IIS The company no longer employs the sysadmin or the guys who set this thing up. (They're not going to employ me much longer either but my sense of professional pride does not permit me to just walk away from this task). The servers are on mutually firewalled networks and I have to perform a convoluted, multi-step process to copy anything from one to the other. Would someone please point me to a crash-course tutorial for accomplishing the above? I have: a complete copy of the site's filesystem on the new box installed the 3rd party charting tool on the new system a config.xml file from the "all tasks - save configuration to a file" right click menu. There doesn't seem to be a way to import it on the new system however. The newer IIS manager has a completely different UI and I'm totally lost. Please help.

  Read the article

• iTunes copy just metadata (song and album ratings, playlists) from iPod

  - by Jared Updike

  I have an iPod touch that I synched with my Windows computer (iTunes 9.0 I think) until my harddrive failed and I lost my entire library. I rebuilt the library (songs) from a year old backup (and various other source for songs) but my playlists and ratings are of course a year old. My iPod itself has most of the playlists and ratings I care most about (favorite songs and albums, rated 4 and 5, for example). I have a catch 22 situation where I feel nervous that I haven't backed up my iPod in around 4 months (when my drive failed) so I'd like to back it up as soon as possible... but if I back it up I have to clear all the songs and playlists and copy them back, which I can't really do since I need to rebuild my playlists on my computer first (using the data only available on my iPod!) The question: is there a better way to READ the information off my iPod than doing it manually, song by song and album by album and playlist by playlist (XML, text dump, database, spreadsheet, anything). In other words, mostly I want the information (metadata like ratings and playlists, not songs) copied off the iPod so I can more quickly get my iTunes library ratings and playlists re-built (manually) so I can finally wipe the music and back up my apps, etc. Then I'd like to copy the music back immediately. The part I'd like to avoid is manually navigating everything on my iPod to read through all the playlists and ratings (50 GB, 6,000+ songs) as I re-enter all of that data by hand. I've done a few dozen albums and it's pretty time consuming having to tap around on the iPod. Reading from a spreadsheet (for example, or XML which I could write a script to get into spreadsheet form) would probably help tremendously, plus then I'd have a backup of that information somewhere besides just my iPod.

  Read the article

• PC -> TV HDMI suddenly doesn't work, any other option does

  - by XSlicer

  So my parents wanted to connect their PC to their TV, so they bought a 10m (35 ft) cable. It all worked perfectly. Then my mom tripped over the cable, breaking it. She somehow got a free replacement, but at the same time some more expensive one from an uncle. Now the problem is that this suddenly doesn't work anymore (TV saying "Format not supported"). I've tried several other things to pinpoint the actual problem, but none brought me something conslusive: PC (hdmi) to TV doesn't work (both cables) PC (hdmi) to TV doesn't work (short cable) Laptop (hdmi) to TV work (same cables) BluRay (hdmi) to TV works (same cables) PC (hdmi) to monitor works (same cables) PC (DVI w/ adapter HDMI) to TV works (same cables) I've tried different ports, tried Linux, reinstalling drivers (the graphics card is internal using an i5 sandy bridge. Normally it's running Windows 7 Home Prem, the TV being a Philips 37PFL7605H). So basically, everything works, except that thing what we want. The only things I am thinking of is that the sound is interfering or that the HDMI-output is somehow broken. Or is it anything else? I'm kind of lost.

  Read the article

• Unable to connect via NetBIOS Name

  - by grom

  I can't connect to machines/shares by NetBIOS names. Below is console output showing the problem. C:\>nbtstat -n Local Area Connection: Node IpAddress: [192.168.1.100] Scope Id: [] NetBIOS Local Name Table Name Type Status --------------------------------------------- BEAST <00> UNIQUE Registered WORKGROUP <00> GROUP Registered BEAST <20> UNIQUE Registered WORKGROUP <1E> GROUP Registered WORKGROUP <1D> UNIQUE Registered ..__MSBROWSE__.<01> GROUP Registered C:\>nbtstat -A 192.168.1.3 Local Area Connection: Node IpAddress: [192.168.1.100] Scope Id: [] NetBIOS Remote Machine Name Table Name Type Status --------------------------------------------- BRCLAPTOP <00> UNIQUE Registered WORKGROUP <00> GROUP Registered BRCLAPTOP <20> UNIQUE Registered WORKGROUP <1E> GROUP Registered MAC Address = 00-1C-BF-14-B8-6E C:\>ping beast Pinging beast [fe80::59b8:179f:b90b:a63f%11] with 32 bytes of data: Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Ping statistics for fe80::59b8:179f:b90b:a63f%11: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms C:\>ping brclaptop Ping request could not find host brclaptop. Please check the name and try again. C:\>nbtstat -a brclaptop Local Area Connection: Node IpAddress: [192.168.1.100] Scope Id: [] Host not found.

  Read the article

• Linux Software RAID1: How to boot after (physically) removing /dev/sda? (LVM, mdadm, Grub2)

  - by flight

  A server set up with Debian 6.0/squeeze. During the squeeze installation, I configured the two 500GB SATA disks (/dev/sda and /dev/sdb) as a RAID1 (managed with mdadm). The RAID keeps a 500 GB LVM volume group (vg0). In the volume group, there's a single logical volume (lv0). vg0-lv0 is formatted with extfs3 and mounted as root partition (no dedicated /boot partition). The system boots using GRUB2. In normal use, the systems boots fine. Also, when I tried and removed the second SATA drive (/dev/sdb) after a shutdown, the system came up without problem, and after reconnecting the drive, I was able to --re-add /dev/sdb1 to the RAID array. But: After removing the first SATA drive (/dev/sda), the system won't boot any more! A GRUB welcome message shows up for a second, then the system reboots. I tried to install GRUB2 manually on /dev/sdb ("grub-install /dev/sdb"), but that doesn't help. Appearently squeeze fails to set up GRUB2 to launch from the second disk when the first disk is removed, which seems to be quite an essential feature when running this kind of Software RAID1, isn't it? At the moment, I'm lost whether this is a problem with GRUB2, with LVM or with the RAID setup. Any hints?

  Read the article

• 1080p monitor: connected through VGA - perfect, HDMI - awful

  - by develroot

  When I connect my 23" monitor (1920x1080) to my pc through HDMI, I encourage some problems. It's not full screen That's it. There are ~1cm black borders on right and left side and ~0,5cm black borders on the top and the bottom of the monitor. That's pretty frustrating. I tried adjusting overscan, but I can't mannualy type the % of overscan that I need. I can only select between ex. 8 and 10% in AMD Vision Engine Control center, but what I need is 9%. Next, even if i select 10% and the image fits all the corners, but after log off all the settings are lost and I have to do it again and again. Text, images, everything looks blurry That surprised me a lot. Should'nt HDMI quality be better than VGA's one? When connected through HDMI, the text isn't readable. It's like a very low refresh rate, although i'm running at 60Hz. Also the text has something like little shadows, very very annoying. Are there any tips to get the same quality as with VGA, with HDMI ? (running on integrated ATI Radeon HD4200, which, appearently, is the best card I have ever seen in terms of integrated ones)

  Read the article

• Requests are making it to my app server, but not into node.js -- why?

  - by Zane Claes

  I detailed in this question on StackOverflow how some random requests are not making it from the client to my Node.js app server, resulting in a gateway timeout. In summary, identical requests are, at random, not even making it far enough to trigger a console.log() in my first line of express middleware. I need to narrow down the problem, though, to find out WHERE the traffic is being lost and it was suggested that I try a packet sniffer on my app servers. Here's my setup: 2x Load Balancers (m1.larges) 2x node.js servers (also m1.large) Here's what's interesting/unusual: the node.js servers started as PHP servers with an Apache stack and continue to serve PHP files for my domain (streamified.me). However, I use a little httpd.conf magic on the app servers so that requests to api.streamified.me get routed over port 8888 to the node.js server: RewriteCond %{HTTP_HOST} ^api.streamified.me RewriteRule ^(.*) http://localhost:8888$1 [P] So, the request hits the load balancer = goes to an app server = gets routed to port 8888 if it's intended for the API = gets handled by node.js So, in the same httpd.conf file, I turned on RewriteLogLevel 5 and then created a simple PHP+CURL script on my localhost to hit my api.streamified.me with a random URL (which should cause node.js to trigger a simple "not found" response) until it resulted in a Gateway timeout. Here, you can see that it has happened -- and the rewrite log shows that the request was definitely received by the app server and forwarded to port 8888... but it was never received by node.js (or, at least, the first line of code in the first line of middleware never gets it...) Image Link: http://i.stack.imgur.com/3OQxS.png

  Read the article

• MySQL ADO.NET Connector & MSSQL Integration Services

  - by user1114330

  Here I am, day three... attempting to sync a data view on a Windows Vista box (64 bit) running MSSQL 2012 and Visual Studio 2010. Sanity is slipping and hunger for progress fills my attention. I went through hell trying to get the MySQL ODBC drivers to get the job but to no avail...everyone seems to be lost and all the threads I can find are solutions that do not work for me. The problem: System DSN's not being seen by SSIS. SSIS DSN Not Showing as ODBC Data Source I make the decision to try out the ADO.NET connector...and to my surprise it is actually in the selection list in data sources in SSIS. So I take off running to create a Data Flow Task, create an ADO.NET Source (a local MSSQL DB)...all is good as usual. Then I move swiftly to creating a ADO.NET Destination, enter my credentials...wow, I am selecting a database finally on my linux server! Happy thinking that I finally have figured a way to get the job done. Then I move to mappings...nope, something is wrong...I am getting an error that hurts my eyes: Pipeline component has returned HRESULT error code 0xC0208457 from a a method call. Error at Data Flow Task [ADO NET Destination [81]]: Failed to get properties of external columns. The table name you entered may not exist or you do not have SELECT permission on the table object and an alternative attempt to get column properties through connection has failed. Detailed error messages are" You have an error in your SQL syntax check the manual that corresponds to your MySQL server version for the right syntax to use near "database".tablename" at line 1. The descriptor files on path C:\Program Files (x86)\Microsoft SQL Server\110\DTS\ProviderDescriptors\ does not contain schema information for connection of type MySQL.Data.MySqlClient.MySqlConnection. So it looks like it can't the information and therefore I cannot map the tables properly. Any ideas on this would be ultra helpful...thanks in advance to All!

  Read the article

< Previous Page | 114 115 116 117 118 119 120 121 122 123 124 125  | Next Page >