Search Results

Search found 18729 results on 750 pages for 'edit'.

Page 113/750 | < Previous Page | 109 110 111 112 113 114 115 116 117 118 119 120  | Next Page >

• How to wire 20 computers and 20 phones and 1 server into LAN?

  - by John Smith

  I have currently 3 switches Two Netgear JFS524 with 24 slots, One Belkin with 16 slots. Server DSL Internet Router. Main question is how to connect switches together, two Netgear's are next to each other, yet one is about 100 feet away and holds about 5 computer and 5 phones. If i connect them with only 1 wire will that limit bandwidth? e.g. all 23 computers will be limited to speed of one CAT5e cable? If i connect switches with 2 cables will this give speed boost? What's the ideal scenario should i just move the third switch next to other two? Will the speed of computer connected to white switch be same as computer connected to top switch? Will moving white switch right next top switch and having 16 wires comming 100 feet instead of 1 wire comming 100 feet make it faster? EDIT 1: I actually have NETGEAR ProSafe GS105 Gigabit switch its only has 4 ports in it though, you think i can have use of it in current setup? Like connect all 3 switches and server into it and keep internet router and phone server on one of the slower switches EDIT 2: Everyone mention gigabit switches, but will they do any difference with 10/100 network cards? I then have to use gigabit cards in every computer too? I could in server perhaps, but users will be 10/100

  Read the article

• Windows Server 2003 DHCP not handing out IPs

  - by SnOrfus

  I'm trying to setup a home server (to tinker with) as a domain controller. I've setup the domain and I've installed DHCP and setup a scope without any exclusions (with the default range of 192.168.0.1-254). My client machine is a Windows 7 (RC) machine and it has a connection but can't get an IP address. Even if I try setting the IP to a static 192.168.0.2 and there is still no connectivity. I can ping it from the server, but pinging the server from the client just times out. The only thing between the server and the client is a 24 port switch (D-Link DES-1024D). edit Ok, it turned out that the interfaces were setup backwards in the NAT settings (the internal nic connection was set to public and the external nic connection was set to private). I changed this and all was OK.... sort-of. Problem is now: If I set a static ip on the client (where I am typing this from) all is fine. BUT; when I set it to get it from DHCP, I get a correct IP from the server (192.168.0.2) but there is no internet on the client; but I can still ping the server fine from the client (which makes sense cause I was able to get an IP from it). edit I ended up just removing the Routing and DHCP server roles and just going with ICS for the time being until I get my hands on some better learning tools.

  Read the article

• mysql mass insert data

  - by user12145

  Edit: I realized that if I construct a large query in memory, the speed has increased almost 10 times of magnitude "insert ignore into xxx(col1, col2) values('a',1), values('b',1), values('c',1)..." Edit: since I have an index on the first column, the insert time creeps up as I insert more. Can I delay the index until the end? Original: I'm using the following to batch insert 10 million rows into mysql db(not all at once, since they don't all fit into memory), it's too slow(taking many hours). should I use load file to improve performance? I would have to create a second file to store all the 10 million rows, then load that into db. are there better ways? PreparedStatement st=con.prepareStatement("insert ignore into xxx (col1, col2) "+ " values (?, 1)"); Iterator d=data.iterator(); while(d.hasNext()){ st.clearParameters(); st.setString(1, (d.next()).toLowerCase()); st.addBatch(); } int[]updateCounts=st.executeBatch();

  Read the article

• AMD FX8350 CPU - CoolerMaster Silencio 650 Case - New Water Cooling System

  - by fat_mike

  Lately after a use of 6 months of my AMD FX8350 CPU I'm experiencing high temperatures and loud noise coming from the CPU fan(I set that in order to keep it cooler). I decided to replace the stock fan with a water cooling system in order to keep my CPU quite and cool and add one or two more case fans too. Here is my case's airflow diagram: http://www.coolermaster.com/microsite/silencio_650/Airflow.html My configuration now is: 2x120mm intake front(stock with case) 1x120mm exhaust rear(stock with case) 1 CPU stock I'm planning to buy Corsair Hydro Series H100i(www.corsair.com/en-us/hydro-series-h100i-extreme-performance-liquid-cpu-cooler) and place the radiator in the front of my case(intake) and add an 120mm bottom intake and/or an 140mm top exhaust fan. My CPU lies near the top of the MO. Is it a good practice to have a water-cooling system that takes air in? As you can see here the front of the case is made of aluminum. Can the fresh air go in? Does it even fit? If not, is it wiser to get Corsair Hydro Series H80i (www.corsair.com/en-us/hydro-series-h80i-high-performance-liquid-cpu-cooler) and place the radiator on top of my case(exhaust) and keep the front 2x120mm stock and add one more as intake on bottom. If you have any other idea let me know. Thank you. EDIT: The CPU fan running ~3000rpm and temp is around 40~43C on idle and save energy. When temp is going over 55C when running multiple programs and servers on localhost(tomcat, wamp) rpm is around 5500 and loud! I'm running Win8.1 CPU not overclocked PS: Due to my reputation i couldn't post the links that was necessary. I will edit ASAP.

  Read the article

• Laptop GPU apparently blew up, motherboard doesn't even turn on its power LED. [But..]

  - by leladax

  EDIT: (Was: Laptop automatic shutdown after 2 seconds) If I take out the GPU, the motherboard LED turns on but then [if it attempts to power up and boot] it turns off after 2 seconds [fans turn on normally in that short period]. [Without the GPUs out there's not even an attempt to boot.] It's an SLI motherboard for a toshiba (model X200-219). If I take out one of the GPUs (they are on top of each other) it surprisingly lets the motherboard turn on too (as it is if both are out) but it still turns off after 2-3 seconds, same behavior. I wonder if it's the GPU that produces the 'turn off after being on' behavior and not something else. [Has anyone seen this behavior with blown up GPUs or could it be something else?] Previous question (before EDIT. Sorry, but someone thought it productive to lock the other one as duplicate): I'm trying to insvestigate which component produces this behavior. Other indications show it may be the GPU but I wonder if anyone knows more. It's a Toshiba Satellite X200 description: AC power shows the power being fed normally, when turned on the fan works and it appears to be starting up but after 2 seconds it shuts down with only the 'AC power connected" led on. -- seconds are about up to 4,maybe not 2 exactly.

  Read the article

• How to create VirtualHost in Ubuntu 12.10

  - by Mifas

  I had followed many articles to 'How to create VirtualHost in Ubuntu'. This is what have I done Installed Apache sudo apt-get install lamp-server^ phpmyadmin I created folder called site1.com in /var/www/ Then I have created the file in /etc/apache2/sites-available/site1.com Then added the following code to that site1.com file <VirtualHost *:80> ServerName www.site1.com ServerAdmin [email protected] ServerAlias site1.com DocumentRoot /var/www/site1.com # Other directives here <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/site1.com/> Options Indexes FollowSymLinks MultiViews AllowOverride all Order allow,deny Allow from all </Directory> </VirtualHost> Then after that I edit the host file added the following line of code 127.0.0.1 site1.com Edit Also I enable the site1.com via sudo a2ensite site1.com Then i restart the apache serivice. (Even i restarted the pc) When I go to the site1.com, It will say The connection has timed out Error Message. But I can browse via localhost/site1.com. I have been trying since last two days. No solution. And followed many articles and videos.

  Read the article

• Querying a CSV file

  - by sheepsimulator

  Does anyone know of a simple tool that will open up a CSV file and let you do basic, SQLesque queries on it? Like a graphical tool of sorts, one that is easy to use. I know I could write a small script to do an import of the CSV into a SQLite database, but since I imagine someone else thought of this before me, I just wanted to inquire if one existed. What's prompting this question is I am getting frustrated with Excel's limited filtering capabilities. Perhaps some other data visualization manipulation tool would provide similar functionality. Free or OSS is preferred, but I'm open to any suggestions. EDIT: I really would prefer some clear tutorials on how to do the below instead of just "make your sheet an ODBC entry" or "write programs using ODBC files", or more ideas on apps to use. Note: I cannot use MS Access. Yet another EDIT: I'm still open for solutions using SQLite. My platform is a semi-ancient Win2k laptop, with a P4 on it. It's quite slow, so a resource-light solution is ideal and would likely get the win.

  Read the article

• 24TB RAID 6 configuration

  - by Phil

  I am in charge of a new website in a niche industry that stores lots of data (10+ TB per client, growing to 2 or 3 clients soon). We are considering ordering about $5000 worth of 3TB drives (10 in a RAID 6 configuration and 10 for backup), which will give us approximately 24 TB of production storage. The data will be written once and remain unmodified for the lifetime of the website, so we only need to do a backup one time. I understand basic RAID theory, however I am not experienced with it. My question is, does this sound like a good configuration? What potential problems could this setup cause? Also, what is the best way to do a one-time backup? Have two RAID 6 arrays, one for offsite backup and one for production? Or should I backup the RAID 6 production array to a JBOD? EDIT: The data server is running Windows 2008 Server x64. EDIT 2: To reduce rebuild time, what would you think about using two RAID 5's instead of one RAID 6?

  Read the article

• Dropbox failing to update?

  - by Mick

  I have two PC's at home. One XP the other Windows 7-64bit. I have a word document that I edit on either PC - to enable this I have the file stored in a Dropbox folder. This usually works fine - but sometimes I find that the file does not get updated on my windows7 PC. I.e. I edit the file on my Windows XP machine, then go to my Windows 7 PC and see that there is a previous, old, datestamp on the file and sure enough if I open up the file to have a look, I see that the latest edits are not included. If I right-click on the file and select "Browse on Dropbox website" I see that the latest file is correctly there. Surely there must be some option to say please update this file - but can find no such thing. Has something gone wrong? I should point out that my wireless internet connection is a little intermittent - could this have caused some glitch? By the way I do not leave the old file open in word on my Windows-7 PC as I can well imagine that would cause trouble. Also I should mention that the icon on the document has the little green tick on it showing that Dropbox is not in the process of doing a transfer. Also the Dropbox icon in my system tray also has the green tick - so Dropbox is not busy transferring some other file(s). If I hover the mouse over the Dropbox icon I get the tooltip "All files up to date".

  Read the article

• How do I install a different OS on a Compaq Presario cq56 with preinstalled SuSE 11?

  - by McCoy

  Thing is, I don't have a clue of Linux systems, I usually use WinXP. Bought a notebook with SuSE 11 on it, because I have my XP licence and thought I could install that if I found the chipset drivers for the hardware (which I'm not completely sure I have the right versions of). Then I thought I'd give it a shot with the SuSE, looked nice enough. But I can't get my external hd to work (tried force mount) and the banshee doesn't do anything like playing video. Since that is one of the two main purposes of this notebook, I need to get that to work. Tried downloading VLC player, but that only works with SuSE 11.1 upwards. So I downloaded a SuSE 11.3 and burned the iso. But surprise, no way the notebook would boot from cd. Same with the XP cd (considered setting up a dual boot). And no, I can't get to BIOS to reset to default, either. So I can basically do nothing else than going online with this thing and that's not enough for me (gamer in withdrawal, yikes!). I need at least to get to my firefox profile on the external hd and be able to watch video. Can somebody please help me? I think at this point I'd prefer to install XP and MAYBE the SuSE 11.3 after that. I'm not a native speaker, so please speak plainly, thanks. :) Edit: if this is impossible, could someone please help me with the external hd mount and video playback? Edit: Found out how to boot from cd by now. But still no XP, because I get bluescreen after bluescreen while setup is loading files. I guess it's the missing SATA drivers...

  Read the article

• how to remove an entry from system tray?

  - by altvali

  I've searched for an answer to this one and I haven't found one yet. How do i remove a single item from Windows' System tray? I'm targeting Windows XP. Edit: This is not about preventing items from starting up. I want the program to keep running, I just need another script/program to remove the first one's entry from system tray. Second Edit: One approach that I can think of is to try to hide the intended app by modifying registry keys. On several test machines I've found some registry entries that match the System tray information at HKEY_USERS\something-that-looks-like S-1-5-21-682003330-1563985344-725345543-1003\Software\Microsoft\Windows\CurrentVersion\Explorer\TrayNotify with BalloonTip, IconStream and PastIconsStream containing systray information. The important one is IconStream. On other machines, these are found at hkey_classes_root/local/setting/software/microsoft/windows/currentversion/TrayNotify I'm quite sure there's no danger in changing those specific registries, but I don't know how to write code for that. Can anyone help me with the code and with confirming if this has the desired effect of hiding the systray icon for an active program?

  Read the article

• Apache2 process stuck at 100% cpu, CLOSE_WAIT socket lingering

  - by mmazing

  I've troubleshooted the heck out of this today, and I can't seem to find any information on how to determine what is happening exactly. Basically, on my development server, another developer is causing CLOSE_WAIT connections that eat up one or more apache2 processes for several hours if I don't restart apache2. strace on any of the processes yields no information, only that it was able to attach. mod_proxy is not enabled. KeepAlive is on, KeepAliveTimeout is 15 seconds, MaxKeepAliveRequests is 100. From what I've been reading, this may or may not be an apache issue at all, just that that's how CLOSE_WAIT works (the server is waiting for a FIN packet to close the connection). I just can't believe that a server would be crippled so easily by not receiving a packet from a remote host telling it to close the connection. Especially without any intervention for well over an hour. Any tips? I'm about to pull my hair out. Edit : Also, there are no unusual entries in any apache log files. Edit 2: lsof -i shows only a single CLOSE_WAIT per hanging process. (That's what has been bothering me about this, as most other discussions talk about many CLOSE_WAIT connections, while I only have one per process.) The nature of the code that is running (php) doesn't really lend itself to closing open connections and whatnot. I can run the same code that he is executing with the same session data, and not result in a hanging process.

  Read the article

• hadoop: port appears open locally but not remotelly

  - by miguel

  I am new to linux and hadoop and I am having the same issue as in this question. I think I understand what is causing it but I don't know how to solve it (Don't know what they mean by "Edit the Hadoop server's configuration file so that it includes its NIC's address."). The other post that they link says that the configuration files should refer to the machine's externally accessible host name. I think I got this right as every hadoop configuration file refers to "master" and the etc/hosts file lists the master by its private IP address. How can I solve this? Edit: I have 5 nodes: master, slavec, slaved, slavee and slavef all running debian. This is the hosts file in master: 127.0.0.1 master 10.0.1.201 slavec 10.0.1.202 slaved 10.0.1.203 slavee 10.0.1.204 slavef this is the hosts file in slavec (it looks similar in the other slaves): 10.0.1.200 master 127.0.0.1 slavec 10.0.1.202 slaved 10.0.1.203 slavee 10.0.1.204 slavef the masters file in master: master the slaves file in master: master slavec slaved slavee slavef the masters and slaves file in slavex has only one line: slavex

  Read the article

• Share Point ACL on OSX Lion Server - Posix group always takes over ACLs

  - by Ben

  Trying to configure a share point on a Lion Server machine. The directory is created by the local server admin (serveradmin) and has rwxr-x--- given to it. The serveradmin user belongs to the local staff group so serveradmin readwrite staff group read Others none We have an OD group for all the employees (Workers) . Using the Server tool we've given Full Control to the share point: Workers Full Control serveradmin readwrite staff group read Others none We would assume that Workers could then do what they want on the share but that doesn't seem to be the case. It appears the POSIX permissions take over the ACL permissions for Worker. If I change the staff permission to readwrite then the Workers can create a file or folder in the share point. I would think the ACL should take over but it doesn't, posix always win, rendering ACL useless. Furthermore if I leave the readwrite permission for staff and take Write permission away for the Workers group then the posix group still wins. Essentially the Workers ACL does absolutely nothing. There are reports of similar problems in this Apple forum thread: https://discussions.apple.com/thread/3722901 The directory nesting fix suggested there doesn't work for us. Has anyone had similar issues and know how to fix this? Edit: in Workgroup Manager the employees user are set to primary group staff and given the additional OD group Workers. Changing their primary group doesn't help, it only shifts the problem onto Others taking over rights (logically) Edit 2: Ok, this is interesting, adding OD Users to the share's ACL works totally fine

  Read the article

• Hard drives (SATA/ATA) corrupting

  - by JC Denton

  Hello All, 2 years ago I bought relatives a new computer for christmas and installed Ubuntu on it. Ever since then it has been experiencing problems with the hard drives. The hard drive supplied with the machine was a SATA drive. When it appeared it was having problems (files and folders with invalid encoding started appearing) I replaced the SATA drive with the drive of their previous computer. I replaced it (The replacement) later on, the drive being rather old and thus becoming more prone to the risk of failure. The replacement drive is a IDE drive but the same problems started to appear (files and folders showing up in nautilus with invalid encoding). I fear the files and folders that are showing are existing FS entries, starting to corrupt. As it's happening to both the IDE and SATA drive it's unlikely to be the drives themselves or the IDE/SATA controller, I believe. Any ideas as to what could be causing the (assumed) corruption? EDIT: You're right about the paragraphs. They were there in edit mode but I'm still getting to grips with the whitespace format codes. The system is a "Primo Pro" AMD Phenom II X4 Quad Core 920 2.80GHz SILENT DDR2, ordered from overclockers.co.uk and nothing has been added to it except for the replacement of the SATA drive with an AMD drive. It would seem unlikely for a barebones system to be underpowered.

  Read the article

• how to properly set environment variables

  - by avorum

  I've recently started using Windows (having used Ubuntu up until now) and I find myself unable to properly set environment variables. Whenever I set them they don't seem to work. I've been going to Start-Edit Environment Variables for your Account and editing the PATH value in the upper half of the GUI. Here's what I've got so far. ;C:\Chocolatey\bin;C:\tools\mysql\current\bin;C:\Program Files (x86)\Git\bin;C:\Program Files\MySQL\MySQL Server 5.6\bin\;C:\Python33\Scripts; These are each the parent directories of the executables I'd like to be able to run by name from CMD, but mysql, git, and pip aren't being recognized. Am I doing something wrong syntactically or at a general understanding level? I'd like to be able to run these commands without having to specify the full path to the executables every time. EDIT: The full PATH extracted from CMD PATH=C:\Python33\;C:\Program Files (x86)\NVIDIA Corporation\PhysX\Common;C:\Program Files (x86)\AMD APP\bin\x86_64;C:\Program Files (x86)\AMD APP\bin\x86;C:\Program Files\Common Files\Microsoft Shared\Windows Live;C:\Program Files (x86)\Common Files\Microsoft Shared\Windows Live;C:\Windows\system32;C:\Windows;C:\Windows\System32\Wbem;C:\Windows\System32\WindowsPowerShell\v1.0\;C:\Program Files (x86)\GTK2-Runtime\bin;C:\Program Files\WIDCOMM\Bluetooth Software\;C:\Program Files\WIDCOMM\Bluetooth Software\syswow64;C:\Program Files (x86)\ATI Technologies\ATI.ACE\Core-Static;C:\Program Files (x86)\Microsoft ASP.NET\ASP.NET Web Pages\v1.0\;C:\Program Files\Microsoft SQL Server\110\Tools\Binn\;C:\Program Files (x86)\QuickTime\QTSystem\;C:\Program Files (x86)\Common Files\Acronis\SnapAPI\;C:\Program Files (x86)\Java\jre7\bin;C:\Program Files (x86)\Windows Kits\8.1\Windows Performance Toolkit\;C:\Program Files (x86)\Microsoft SDKs\TypeScript\;C:\Program Files (x86)\MySQL\MySQL Utilities 1.3.4\; ;C:\Chocolatey\bin;C:\tools\mysql\current\bin I'm being forced to use Windows by my work environment, I don't enjoy the state of affairs.

  Read the article

• Development on Windows 7; Web server on Linux - How to share Apache web root?

  - by TheKeys

  I've got a LAMP server that I want to use as a local web server. I've got a Windows 7 machine that I want to use as my development machine. The machines will be on the same LAN (or the Windows box will be VPNed into the LAN). My questions is, what is the best way of sharing the web root of the LAMP server so that I can edit the files on the remote Windows 7 machine and how do I go about configuring this on the Linux machine? (Fedora 16) I would like the solution to be as easy to use as possible with preferably no extra steps required to save/edit/upload files from my IDE on my Windows 7 machine. I'm thinking either a Samba or NFS share are the way to go but I'm concerned I'm going to run into issues with permissions and unix/windows file handling. Is one better than ther other for my use case or is there a better alternative solution? I'm currently using Windows 7 Professional which doesn't have NFS support but would upgrade to Ultimate which does have NFS support if it's the best solution.

  Read the article

• Massive SQL issue shutting down our site.

  - by Pselus

  Our website has started timing out like crazy today. All of our clients are finding it unusable. The only error we can seem to trace down as a potential problem is this: SQLAllocHandle on SQL_HANDLE_DBC failed Error ASP Description Error Category Microsoft OLE DB Provider for ODBC Drivers I have no idea what it means or how to go about fixing it. Anyone ever encountered this error before? Currently, you can log in to our site, but then once you go to do anything else, you find yourself logged out or nothing happens. We have a lot of Ajax going on so the "nothing happens" probably has to do with the Ajax pages not loading properly due to logouts and so nothing displays to the user. Like I said, I'm at a loss. Anyone have any advice on this error? EDIT I realize that this isn't necessarily a programming question, but we are a small startup company that just yesterday started talking about how we need to get a backup server running. Apparently we talked about it too late. We don't have a DBA, just 2 mid level programmers trying their hardest to keep our clients happy. So please, if you have any assistance give it but please don't close my question right now. EDIT 2 Turns out we had something on our server running called "ServerMask" that makes our IIS server look like Apache to the outside world. Shutting it down fixed our issue. Still no idea why it was messing up but it was the problem apparently. Thanks to everyone who tried to help.

  Read the article

• DNS NAmeserver Aname and cname records

  - by David

  Hi - I am inexperienced in the configuration of DNS and have an issue with dominan hosting set up. I have two domains 'www.mydomain1.com' and 'www.mydomain2.com', with mydomain2 pointed at the same place as mydomain1. The domains were passed to me recently by the person who previoulsy controlled them. I have an account with fasthosts in the uk. When I accepted the domains I could not access the DNS settings and enquired with fasthosts as to why. The replied saying 'The delegate hosting option for both domains were enabled and this is the reason why you were unable to find the option to edit the advanced DNS records. I have now disabled the delegate hosting option so you can now edit the advanced DNS records for both domains in your account.' When i log into the fasthost control panel now i can access the DNS controls but both domains have no A Record of Cname record set up. I am concerned that fasthosts have blatted the previous Nameserver entries and set me up on theirs but not added any record. 'www.mydomain1.com' currently still works but 'www.mydomain2.com' does not find the site anymore. i am worried i will lose mydomain1 to as teh dns changes filter through the system. my webhosting is at 'xxx.xxx.xxx.xxx/mydomain1.com/' and this is where I want both domains to point. Any advice would be much appreciated. one thing which is confusing me is that because I am on a shared server I have to put 'xxx.xxx.xxx.xxx/mydomain1.com/' to get to my site rather than just 'xxx.xxx.xxx.xxx'. The form on fasthosts for the aname record only allows an IP to be entered - does it add the mydomain1.com/ onto the end itself? Thanks for any help given - I'm quite worried about this David

  Read the article

• cron doesn't execute any task, but writes into log as executed

  - by FractalizeR

  I have strange problem on one of my servers. Cron does not execute any task, but it writes to it's log, that task has been executed successfully. Like some simulation mode is activated... Apr 30 03:03:08 nd-10049 crond[13387]: (root) CMD (php /usr/local/frb/backup.php) Apr 30 03:05:01 nd-10049 crond[13397]: (root) CMD (php /home/support/public_html/cron/cron_hourly.php>/home/support/public_html/cron/hourly.log) Apr 30 03:09:01 nd-10049 crond[19108]: (root) CMD (/etc/webmin/cron/tempdelete.pl ) Apr 30 03:10:01 nd-10049 crond[19467]: (root) CMD (php /home/support/public_html/cron/cron_hourly.php>/home/support/public_html/cron/hourly.log) Apr 30 03:14:44 nd-10049 crontab[21154]: (root) BEGIN EDIT (root) Apr 30 03:15:01 nd-10049 crond[21309]: (root) CMD (php /home/support/public_html/cron/cron_hourly.php>/home/support/public_html/cron/hourly.log) Apr 30 03:15:38 nd-10049 crontab[21154]: (root) REPLACE (root) Apr 30 03:15:38 nd-10049 crontab[21154]: (root) END EDIT (root) Apr 30 03:16:01 nd-10049 crond[14961]: (root) RELOAD (cron/root) Apr 30 03:20:02 nd-10049 crond[22620]: (root) CMD (php /home/support/public_html/cron/cron_hourly.php) There are no errors about cron in common log (messages). The OS is CentOS. What can I do to check what is the problem? What can the problem be?

  Read the article

• legit emails in junkbox

  - by acidzombie24

  Hey this is actually a reverse question. My personal email ([email protected]) is winding up in many peoples junkbox and I have no idea why. What may the cause be? Is it because it has the word Entrepreneur (and programmer) in my sig? is it because my first name is unique(european like)? Its driving me crazy. I sent out dozens of business emails a month to people I just meet so its actually hurting me much more then others :( -edit- I also want to mention this is non spam. Typically I email people I meet and say hi or to follow up. I was requested by someone to send him an email so I can test something, so I did and he replied to me 10 days later telling me he found it in his junk, like many others have said to me. -edit- bortzmeyer suggested emailing [email protected] I did and here are the results SPF check: pass DomainKeys check: pass DKIM check: pass Sender-ID check: pass SpamAssassin check: ham ---------------------------------------------------------- SpamAssassin check details: ---------------------------------------------------------- SpamAssassin v3.2.5 (2008-06-10) Result: ham (-2.6 points, 5.0 required) pts rule name description ---- ---------------------- -------------------------------------------------- -0.0 SPF_PASS SPF: sender matches SPF record -2.6 BAYES_00 BODY: Bayesian spam probability is 0 to 1% [score: 0.0000] 0.0 HTML_MESSAGE BODY: HTML included in message

  Read the article

• DEB: "Provides:" field ignored

  - by Creshal

  I need to replace a package with a custom one, which gets its own name (foo-origpackage). To allow it to be used as drop-in replacement, I added the Provides: origpackage line to the control file. apt-cache show foo-origpackage lists the "Provides" entry just fine. However, when I want to install a file depending on origpackage, it fails ("Package origpackage not installed"). Is there some distinction between "real" and virtual packages I'm missing? EDIT: To be precise, what I want to replace is xen-utils-common for Squeeze. My tao-xen-utils-common has the following control file: Source: tao-xen-utils-common Section: kernel Priority: optional Maintainer: Creshal <[email protected]> Build-Depends: debhelper Standards-Version: 3.8.0 Homepage: http://tao.at Package: tao-xen-utils-common Architecture: all Depends: gawk, lsb-base, udev, xenstore-utils, tao-firewall Provides: xen-utils-common Conflicts: xen-utils-common Replaces: xen-utils-common Description: Xen administrative tools - common files (modified) The userspace tools to manage a system virtualized through the Xen virtual machine monitor. Modified for use with TAO Firewall. Installing xen-utils-4.0 fails, however: foo@bar# apt-cache showpkg tao-xen-utils-common Package: tao-xen-utils-common Versions: 4.0.0-1tao1 (/var/lib/apt/lists/repo.tao.at_dists_stable_main_binary-amd64_Packages) (/var/lib/dpkg/status) Description Language: File: /var/lib/apt/lists/repo.tao.at_dists_stable_main_binary-amd64_Packages MD5: 7c2503f563fca13b33b4eb3cbcb3c129 Reverse Depends: tao-firewall,tao-xen-utils-common tao-firewall,tao-xen-utils-common Dependencies: 4.0.0-1tao1 - gawk (0 (null)) lsb-base (0 (null)) udev (0 (null)) xenstore-utils (0 (null)) tao-firewall (0 (null)) xen-utils-common (0 (null)) xen-utils-common (0 (null)) Provides: 4.0.0-1tao1 - xen-utils-common Reverse Provides: foo@bar# apt-get install xen-utils-4.0 Reading package lists... Done Building dependency tree Reading state information... Done The following extra packages will be installed: xen-utils-common Suggested packages: xen-docs-4.0 The following packages will be REMOVED: tao-xen-utils-common The following NEW packages will be installed: xen-utils-4.0 xen-utils-common Edit:foo@bar# apt-cache policy xen-utils-4.0 xen-utils-4.0: Installed: (none) Candidate: 4.0.1-4 Version table: 4.0.1-4 0 500 http://ftp.at.debian.org/debian/ stable/main amd64 Packages 4.0.1-4 0 500 http://security.debian.org/ stable/updates/main amd64 Packages

  Read the article

• Postfix does not work after setting server hostname from plesk

  - by Michael

  I have recently set my server hostname from localhost.localdomain to xx.mydomain.com from the plesk control panel. However after doing this change postfix has stopped working, I tried restarting and regenerating the config files but to no avail. I am not familiar with postfix but I believe there is a setting to be changed in main.cf. Here are the relevant errors I receive: postfix/postfix-script: starting the Postfix mail system postfix/master: daemon started -- version 2.8.4, configuration /etc/postfix postfix/cleanup: fatal: host/service localhost/12768 not found: Name or service not known postfix/pickup: warning: maildrop/E5559996219: error writing 4FA2C996217: queue file write error postfix/master: warning: process /usr/libexec/postfix/cleanup pid 15334 exit status 1 postfix/master: warning: /usr/libexec/postfix/cleanup: bad command startup -- throttling Any ideas? EDIT Setting it back to localhost.localdomain makes it work again. The only references to localhost/12768 I can find in main.cf are: smtpd_milters = inet:localhost:12768 non_smtpd_milters = inet:localhost:12768 Should something be changed here? These two lines stay the same when I change the hostname. EDIT If I comment out the two mail filter lines (the ones shown above) and restart, postfix works with the new hostname. However this is obviously not the ideal solution...

  Read the article

• Passive FTP Server Port Configuration Troubles Win2003

  - by Chris

  Win2003 Ports 20 & 21 are open IIS6 - Direct Metabase Edit enabled Configured FTP service passive range to 5500-5550 5500-5550 added to windows firewall iisreset and double checked by restarting ftp service nothing has changed, when I connect and enter passive, it still hangs when ever I try to LIST or transfer files. Active is just as useless. Microsoft Windows [Version 6.1.7600] Copyright (c) 2009 Microsoft Corporation. All rights reserved. C:\Users\user>ftp ftp> open x.x.x.x Connected to x.x.x.x. 220-Microsoft FTP Service xxxxxxxxxxxxxxxxxx 220 xxxxxxxxxxxxxxxxxx User (x.x.x.x:(none)): user 331 Password required for user. Password: 230-YOUR ACTIVITY IS BEING RECORDED TO THE FULLEST EXTENT 230 User user logged in. ftp> QUOTE PASV 227 Entering Passive Mode (82,19,25,134,21,124) ftp> ls 200 PORT command successful. 150 Opening ASCII mode data connection for file list. and it hangs.. Now I can see from microsooft documentation that on newer windows releases, additional steps such as these are suggested, but they dont work on 2003... netsh advfirewall firewall add rule name=”FTP Service” action=allow service=ftpsvc protocol=TCP dir=in netsh advfirewall set global StatefulFTP disable is there anything I am missing, what is this StatefulFTP malarkey at the end EDIT I can connect and transfer binary files using WinSCP client - Therefore the problem must be with my ftp commands no? Can anyone see anything wrong with my windows ftp client example? why would it hang on ls, i tried QUOTE LIST as well, and that just hangs, and the windows ftp client doesnt work in active, it hangs if I try to go "binary" then put - This worked before I added 5500-5550 on the router. I have since added this range to the router but no difference to the windows ftp client.

  Read the article

• Are there cloud network drives that let users lock files or mark them as "in use"?

  - by Brandon Craig Rhodes

  Having spent several hours reading about the features and limitations of services like DropBox and Jungle Disk and the hundreds of competitors they seem to have (as though everyone with an AWS account these days goes ahead and writes a file sharing application just for fun), I have yet to find one that would let a team of people at a small business collaborate without stepping all over each other's toes. At a small business there are often many small documents per project — estimates, contracts, project plans, budgets — and team members frequently have to open and edit them, with all sorts of problems happening if two people edit a file at once. Even if a sharing service is smart enough to keep both versions of the file created, most small-business software (like word processors, spreadsheets, estimating software, or billing systems) has no way to compare — much less to merge! — the changes in two rival versions of a file that two people edited at the same time without each other's knowledge. So, my question: are their cloud-based file sharing solutions that not only provide a virtual network drive that people can access, but that also let users lock files — even if it's not a real lock but just a flag or indicator — that could possibly prevent remote workers from both editing the same file at once? Having one person wait for another person to finish editing is a very, very small inconvenience compared to the hour or more than it can take to compare two estimates by hand until you find and resolve the rival changes. Given this fact, I am surprised that almost none of the popular file sharing solutions seem to recognize this problem and provide some solution! Does anyone know of a service that does?

  Read the article

< Previous Page | 109 110 111 112 113 114 115 116 117 118 119 120  | Next Page >