Search Results

Search found 3033 results on 122 pages for 'manual'.

Page 114/122 | < Previous Page | 110 111 112 113 114 115 116 117 118 119 120 121  | Next Page >

• Can't get the L2TP IPSEC up and running

  - by Maciej Swic

  i have an Ubuntu 11.10 (oneiric) server running on a ReadyNAS. Im planning to use this to accept ipsec+l2tp connections through a router. However, the connection is failing somewhere half through. Using Openswan IPsec U2.6.28/K3.0.0-12-generic and trying to connect with an iOS 5 iPhone 4S. This is how far i can get: auth.log: Jan 19 13:54:11 ubuntu pluto[1990]: added connection description "PSK" Jan 19 13:54:11 ubuntu pluto[1990]: added connection description "L2TP-PSK-NAT" Jan 19 13:54:11 ubuntu pluto[1990]: added connection description "L2TP-PSK-noNAT" Jan 19 13:54:11 ubuntu pluto[1990]: added connection description "passthrough-for-non-l2tp" Jan 19 13:54:11 ubuntu pluto[1990]: listening for IKE messages Jan 19 13:54:11 ubuntu pluto[1990]: NAT-Traversal: Trying new style NAT-T Jan 19 13:54:11 ubuntu pluto[1990]: NAT-Traversal: ESPINUDP(1) setup failed for new style NAT-T family IPv4 (errno=19) Jan 19 13:54:11 ubuntu pluto[1990]: NAT-Traversal: Trying old style NAT-T Jan 19 13:54:11 ubuntu pluto[1990]: adding interface eth0/eth0 192.168.19.99:500 Jan 19 13:54:11 ubuntu pluto[1990]: adding interface eth0/eth0 192.168.19.99:4500 Jan 19 13:54:11 ubuntu pluto[1990]: adding interface lo/lo 127.0.0.1:500 Jan 19 13:54:11 ubuntu pluto[1990]: adding interface lo/lo 127.0.0.1:4500 Jan 19 13:54:11 ubuntu pluto[1990]: adding interface lo/lo ::1:500 Jan 19 13:54:11 ubuntu pluto[1990]: adding interface eth0/eth0 2001:470:28:81:a00:27ff:* Jan 19 13:54:11 ubuntu pluto[1990]: loading secrets from "/etc/ipsec.secrets" Jan 19 13:54:11 ubuntu pluto[1990]: loading secrets from "/var/lib/openswan/ipsec.secrets.inc" Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [RFC 3947] method set to=109 Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike] method set to=110 Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: ignoring unknown Vendor ID payload [8f8d83826d246b6fc7a8a6a428c11de8] Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: ignoring unknown Vendor ID payload [439b59f8ba676c4c7737ae22eab8f582] Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: ignoring unknown Vendor ID payload [4d1e0e136deafa34c4f3ea9f02ec7285] Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: ignoring unknown Vendor ID payload [80d0bb3def54565ee84645d4c85ce3ee] Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: ignoring unknown Vendor ID payload [9909b64eed937c6573de52ace952fa6b] Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03] meth=108, but already using method 110 Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02] meth=107, but already using method 110 Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n] meth=106, but already using method 110 Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [Dead Peer Detection] Jan 19 14:04:31 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: responding to Main Mode from unknown peer 95.*.*.233 Jan 19 14:04:31 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: transition from state STATE_MAIN_R0 to state STATE_MAIN_R1 Jan 19 14:04:31 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: STATE_MAIN_R1: sent MR1, expecting MI2 Jan 19 14:04:33 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: NAT-Traversal: Result using draft-ietf-ipsec-nat-t-ike (MacOS X): both are NATed Jan 19 14:04:33 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: transition from state STATE_MAIN_R1 to state STATE_MAIN_R2 Jan 19 14:04:33 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: STATE_MAIN_R2: sent MR2, expecting MI3 Jan 19 14:05:03 ubuntu pluto[1990]: ERROR: asynchronous network error report on eth0 (sport=500) for message to 95.*.*.233 port 500, complainant 95.*.*.233: Connection refused [errno 111, origin ICMP type 3 code 3 (not authenticated)] Router config UDP 500, 1701 and 4500 forwarded to 192.168.19.99 (Ubuntu server for ipsec). Ipsec passthrough enabled. /etc/ipsec.conf # /etc/ipsec.conf - Openswan IPsec configuration file # This file: /usr/share/doc/openswan/ipsec.conf-sample # # Manual: ipsec.conf.5 version 2.0 # conforms to second version of ipsec.conf specification config setup nat_traversal=yes #charonstart=yes #plutostart=yes protostack=netkey conn PSK authby=secret forceencaps=yes pfs=no auto=add keyingtries=3 dpdtimeout=60 dpdaction=clear rekey=no left=192.168.19.99 leftnexthop=192.168.19.1 leftprotoport=17/1701 right=%any rightprotoport=17/%any rightsubnet=vhost:%priv,%no dpddelay=10 #dpdtimeout=10 #dpdaction=clear include /etc/ipsec.d/l2tp-psk.conf /etc/ipsec.d/l2tp-psk.conf conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT # # PreSharedSecret needs to be specified in /etc/ipsec.secrets as # YourIPAddress %any: "sharedsecret" authby=secret pfs=no auto=add keyingtries=3 # we cannot rekey for %any, let client rekey rekey=no # Set ikelifetime and keylife to same defaults windows has ikelifetime=8h keylife=1h # l2tp-over-ipsec is transport mode type=transport # left=192.168.19.99 # # For updated Windows 2000/XP clients, # to support old clients as well, use leftprotoport=17/%any leftprotoport=17/1701 # # The remote user. # right=%any # Using the magic port of "0" means "any one single port". This is # a work around required for Apple OSX clients that use a randomly # high port, but propose "0" instead of their port. rightprotoport=17/%any dpddelay=10 dpdtimeout=10 dpdaction=clear conn passthrough-for-non-l2tp type=passthrough left=192.168.19.99 leftnexthop=192.168.19.1 right=0.0.0.0 rightsubnet=0.0.0.0/0 auto=route /etc/ipsec.secrets include /var/lib/openswan/ipsec.secrets.inc %any %any: PSK "my-key" 192.168.19.99 %any: PSK "my-key" /etc/xl2tpd/xl2tpd.conf [global] debug network = yes debug tunnel = yes ipsec saref = no listen-addr = 192.168.19.99 [lns default] ip range = 192.168.19.201-192.168.19.220 local ip = 192.168.19.99 require chap = yes refuse chap = no refuse pap = no require authentication = no ppp debug = yes pppoptfile = /etc/ppp/options.xl2tpd length bit = yes /etc/ppp/options.xl2tpd pcp-accept-local ipcp-accept-remote noccp auth crtscts idle 1800 mtu 1410 mru 1410 defaultroute debug lock proxyarp connect-delay 5000 ipcp-accept-local /etc/ppp/chap-secrets # Secrets for authentication using CHAP # client server secret IP addresses maciekish * my-secret * * maciekish my-secret * I can't seem to find the problem. Other ipsec connections to other hosts work from the network im currently at.

  Read the article

• Need help diagnosing network performance issues

  - by tokes

  I am currently working in a developing country as a system analyst for a government department. My area of expertise is software projects, but I've come across a few issues with the network setup in my office. (Unfortunately, being a developing country, there's not a lot of professional help available for this sort of thing.) Most recently, I am trying to diagnose a problem with slowness on the network. Our office is connected to the internet via an ADSL wireless modem/router (called Router). The modem is connected via ethernet to a switch (called Switch). The modem also acts as a wireless access point (called Wireless1), though because it is in a room at the end of the floor, it's range is limited. There are ethernet ports installed around the office. The cables of these all lead back to the same switch. In closer vicinity to the bulk of the client computers, there is another wireless router that acts as an access point for those clients (called Wireless2). That router is connected via ethernet to a wall port, and therefore to Switch. There is also a Windows server which acts as a DNS server (called DNSBox) which is located in the same room and is connected directly to Switch. ---Internet----------| Router/Wireless1 192.168.10.1 ---------------| |----|=========| DNSBox | |-------------------- 192.168.10.4 --------------------| Switch |---Other clients---- | |-------------------- |----|=========| Wireless2 ------------------| 192.168.10.198 One final thing to mention about the network setup. All clients are configured with manual IP addresses. Their router/gateway is set to the IP address of Router, and their DNS server is set to the IP address of DNSBox (with a secondary IP set to an external IP - that of our ISP's DNS server). Here are the symptoms we are experiencing: Clients connected to Wireless2 AP experience slow and unstable connections to the internet. (Slow here is defined as speeds of ~1KB/s, though ping response times seem to be as normal.) Clients connected via ethernet to Switch also experience the same slowness. Clients connected to Wireless1 AP (i.e. connecting via wireless directly to the ADSL modem) experience normal connections to the internet. Clients connected via ethernet to Router (i.e. connecting via ethernet directly to the ADSL modem) also experience normal connections to the internet. I also tried to gauge the connection performance between two machines on the network via ethernet: A file transfer between two clients who were both directly connected to Switch was the fastest; A file transfer between one client directly connected to Switch, and one client directly connected to Router (which is directly connected to Switch) performed much slower; A file transfer between two clients directly connected to Router also performed slowly. Things I have attempted to diagnose the problem: Restarted Switch -- no change. We tried unplugging ethernet jacks from Switch 4 at a time and testing the internet connection. The thought here was that perhaps a client on the network has contracted a virus, and is possibly spamming the network with traffic? (Not very technical, I know.) Unfortunately we couldn't get any significant increases in performance using this method. There were a couple of times when it seemed to be better, but then the connection speed quickly dropped back to slow/dead pace. I didn't want to unplug all jacks from Switch because I was concerned that users might be affected or that I would re-plug in the jacks incorrectly (should I even be worried about that? a port is a port on a switch, right?) I tried swapping the ethernet cable used to connect Router to Switch -- no change in performance. I tried swapping the port used on Switch for Router -- no change in performance. Anyone got any ideas on what this could be? Should I be mentioning specific brand names/models of the hardware used? Virii outbreaks are common in this country/office -- what could I be doing to figure out if a virus is at fault? If it is a virus, it doesn't seem to be generating a lot of traffic to/from the internet, because a) I can still get a good speed if I am directly connected to Router / Wireless1 and b) our ISP data usage has not risen suspiciously. Thanks for your help! Update #1 Here are the specs of some of the hardware: Switch is an Edimax ES3132RL 32-Port 10/100 Rackmount Switch Router is a D-Link DSL-G604T Update #2 I just tried unplugging everything except a laptop and Router from Switch. Speeds are still slow. I guess that means that Router / Switch are not being flooded? It seems more and more likely that the cause is something to do with the interaction between Router and Switch. However, I still can't find any useful resources on setting the LAN speed for either (and I'm not well-versed in these advanced networking configurations).

  Read the article

• Can't get FTP to work on centOS 5.6

  - by josi

  Hi guys I have been trying for a few hours to install and get FTP to work... I did yum install ftp and yum install vsftpd They all installed and are running but when I try to use filezilla or some other client I just can't connect....I've tried connecting on port 21 and port 990 ....nothing! These are my iptables # Firewall configuration written by system-config-securitylevel # Manual customization of this file is not recommended. *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :RH-Firewall-1-INPUT - [0:0] -A INPUT -j RH-Firewall-1-INPUT -A FORWARD -j RH-Firewall-1-INPUT -A RH-Firewall-1-INPUT -i lo -j ACCEPT -A RH-Firewall-1-INPUT -p icmp --icmp-type any -j ACCEPT -A RH-Firewall-1-INPUT -p 50 -j ACCEPT -A RH-Firewall-1-INPUT -p 51 -j ACCEPT -A RH-Firewall-1-INPUT -p esp -j ACCEPT -A RH-Firewall-1-INPUT -p ah -j ACCEPT -A RH-Firewall-1-INPUT -d 224.0.0.251 -p udp -m udp --dport 5353 -j ACCEPT -A RH-Firewall-1-INPUT -p udp -m udp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m tcp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 22 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 443 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 21 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 25 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 53 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 110 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 990 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 443 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 465 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 646 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 993 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 995 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 3306 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 10009 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 7778 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 5000 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 25566 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 8765 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 8192 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 8123 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 20 -j ACCEPT -A RH-Firewall-1-INPUT -p udp -m state --state NEW -m udp --dport 23877 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 9091 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 51413 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 10011 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 30033 -j ACCEPT -A RH-Firewall-1-INPUT -p udp --dport 5353 -d 224.0.0.251 -j ACCEPT -A RH-Firewall-1-INPUT -p udp -m udp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m tcp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT -A RH-Firewall-1-INPUT -j REJECT --reject-with icmp-host-prohibited COMMIT Any help would be much appreciated! If I do lsof -i :21 without the "." it shows nothing. [root@ks3000420 ~]# lsof -i :21 . COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME bash 9964 root cwd DIR 8,1 4096 483329 . bash 11608 root cwd DIR 8,1 4096 483329 . bash 13550 root cwd DIR 8,1 4096 483329 . vi 14117 root cwd DIR 8,1 4096 483329 . sftp-serv 15261 root cwd DIR 8,1 4096 483329 . sftp-serv 15477 root cwd DIR 8,1 4096 483329 . bash 19074 root cwd DIR 8,1 4096 483329 . lsof 19100 root cwd DIR 8,1 4096 483329 . lsof 19101 root cwd DIR 8,1 4096 483329 .

  Read the article

• MySQL is hogging my server resources

  - by Reacen

  Does anyone have any idea of what can cause this weird behaviour and how I go about fixing it? This is all coming from MySQL only (both RAM and CPU usage), for about 10 minutes after I reboot my Java game server (that has a pool of 256 connections). There are not that many queries and I think it may be more of a MySQL misconfiguration problem. My server: 3.20 GHz * 6 core / 24 GB RAM / 64 bit Windows Server 2003. My game server: Java server, with 256 MySQL connections pool (MyISAM engine), about 500,000 accounts, and 9 million rows of game items in database and about 3,000 players are connected. After about 15 minutes of the game server reboot, the server resumes its stability and CPU usage drop down to 1% ~ 5% and memory to 6 GB. Here is a copy of my MySQL configuration. Also, any advice about my MySQL configuration will be appreciated. I really set it up almost at random. # Example MySQL config file for very large systems. # # This is for a large system with memory of 1G-2G where the system runs mainly # MySQL. # # You can copy this file to # /etc/my.cnf to set global options, # mysql-data-dir/my.cnf to set server-specific options (in this # installation this directory is C:\mysql\data) or # ~/.my.cnf to set user-specific options. # # In this file, you can use all long options that a program supports. # If you want to know which options a program supports, run the program # with the "--help" option. # The following options will be passed to all MySQL clients [client] #password = your_password port = 3306 socket = /tmp/mysql.sock # Here follows entries for some specific programs # The MySQL server [mysqld] #log=c:\mysql.log port = 3306 socket = /tmp/mysql.sock skip-locking key_buffer_size = 2572M max_allowed_packet = 64M table_open_cache = 512 sort_buffer_size = 128M read_buffer_size = 128M read_rnd_buffer_size = 128M myisam_sort_buffer_size = 500M thread_cache_size = 32 query_cache_size = 1948M # Try number of CPU's*2 for thread_concurrency thread_concurrency = 12 max_connections = 5000 # Don't listen on a TCP/IP port at all. This can be a security enhancement, # if all processes that need to connect to mysqld run on the same host. # All interaction with mysqld must be made via Unix sockets or named pipes. # Note that using this option without enabling named pipes on Windows # (via the "enable-named-pipe" option) will render mysqld useless! # #skip-networking # Replication Master Server (default) # binary logging is required for replication log-bin=mysql-bin # required unique id between 1 and 2^32 - 1 # defaults to 1 if master-host is not set # but will not function as a master if omitted server-id = 1 # Replication Slave (comment out master section to use this) # # To configure this host as a replication slave, you can choose between # two methods : # # 1) Use the CHANGE MASTER TO command (fully described in our manual) - # the syntax is: # # CHANGE MASTER TO MASTER_HOST=<host>, MASTER_PORT=<port>, # MASTER_USER=<user>, MASTER_PASSWORD=<password> ; # # where you replace <host>, <user>, <password> by quoted strings and # <port> by the master's port number (3306 by default). # # Example: # # CHANGE MASTER TO MASTER_HOST='125.564.12.1', MASTER_PORT=3306, # MASTER_USER='joe', MASTER_PASSWORD='secret'; # # OR # # 2) Set the variables below. However, in case you choose this method, then # start replication for the first time (even unsuccessfully, for example # if you mistyped the password in master-password and the slave fails to # connect), the slave will create a master.info file, and any later # change in this file to the variables' values below will be ignored and # overridden by the content of the master.info file, unless you shutdown # the slave server, delete master.info and restart the slaver server. # For that reason, you may want to leave the lines below untouched # (commented) and instead use CHANGE MASTER TO (see above) # # required unique id between 2 and 2^32 - 1 # (and different from the master) # defaults to 2 if master-host is set # but will not function as a slave if omitted #server-id = 2 # # The replication master for this slave - required #master-host = <hostname> # # The username the slave will use for authentication when connecting # to the master - required #master-user = <username> # # The password the slave will authenticate with when connecting to # the master - required #master-password = <password> # # The port the master is listening on. # optional - defaults to 3306 #master-port = <port> # # binary logging - not required for slaves, but recommended #log-bin=mysql-bin # # binary logging format - mixed recommended #binlog_format=mixed # Point the following paths to different dedicated disks #tmpdir = /tmp/ #log-update = /path-to-dedicated-directory/hostname # Uncomment the following if you are using InnoDB tables #innodb_data_home_dir = C:\mysql\data/ #innodb_data_file_path = ibdata1:2000M;ibdata2:10M:autoextend #innodb_log_group_home_dir = C:\mysql\data/ # You can set .._buffer_pool_size up to 50 - 80 % # of RAM but beware of setting memory usage too high #innodb_buffer_pool_size = 384M #innodb_additional_mem_pool_size = 20M # Set .._log_file_size to 25 % of buffer pool size #innodb_log_file_size = 100M #innodb_log_buffer_size = 8M #innodb_flush_log_at_trx_commit = 1 #innodb_lock_wait_timeout = 50 [mysqldump] quick max_allowed_packet = 64M [mysql] no-auto-rehash # Remove the next comment character if you are not familiar with SQL #safe-updates [myisamchk] key_buffer_size = 256M sort_buffer_size = 256M read_buffer = 8M write_buffer = 8M [mysqlhotcopy] interactive-timeout

  Read the article

• Improving SAS multipath to JBOD performance on Linux

  - by user36825

  Hello all I'm trying to optimize a storage setup on some Sun hardware with Linux. Any thoughts would be greatly appreciated. We have the following hardware: Sun Blade X6270 2* LSISAS1068E SAS controllers 2* Sun J4400 JBODs with 1 TB disks (24 disks per JBOD) Fedora Core 12 2.6.33 release kernel from FC13 (also tried with latest 2.6.31 kernel from FC12, same results) Here's the datasheet for the SAS hardware: http://www.sun.com/storage/storage_networking/hba/sas/PCIe.pdf It's using PCI Express 1.0a, 8x lanes. With a bandwidth of 250 MB/sec per lane, we should be able to do 2000 MB/sec per SAS controller. Each controller can do 3 Gb/sec per port and has two 4 port PHYs. We connect both PHYs from a controller to a JBOD. So between the JBOD and the controller we have 2 PHYs * 4 SAS ports * 3 Gb/sec = 24 Gb/sec of bandwidth, which is more than the PCI Express bandwidth. With write caching enabled and when doing big writes, each disk can sustain about 80 MB/sec (near the start of the disk). With 24 disks, that means we should be able to do 1920 MB/sec per JBOD. multipath { rr_min_io 100 uid 0 path_grouping_policy multibus failback manual path_selector "round-robin 0" rr_weight priorities alias somealias no_path_retry queue mode 0644 gid 0 wwid somewwid } I tried values of 50, 100, 1000 for rr_min_io, but it doesn't seem to make much difference. Along with varying rr_min_io I tried adding some delay between starting the dd's to prevent all of them writing over the same PHY at the same time, but this didn't make any difference, so I think the I/O's are getting properly spread out. According to /proc/interrupts, the SAS controllers are using a "IR-IO-APIC-fasteoi" interrupt scheme. For some reason only core #0 in the machine is handling these interrupts. I can improve performance slightly by assigning a separate core to handle the interrupts for each SAS controller: echo 2 /proc/irq/24/smp_affinity echo 4 /proc/irq/26/smp_affinity Using dd to write to the disk generates "Function call interrupts" (no idea what these are), which are handled by core #4, so I keep other processes off this core too. I run 48 dd's (one for each disk), assigning them to cores not dealing with interrupts like so: taskset -c somecore dd if=/dev/zero of=/dev/mapper/mpathx oflag=direct bs=128M oflag=direct prevents any kind of buffer cache from getting involved. None of my cores seem maxed out. The cores dealing with interrupts are mostly idle and all the other cores are waiting on I/O as one would expect. Cpu0 : 0.0%us, 1.0%sy, 0.0%ni, 91.2%id, 7.5%wa, 0.0%hi, 0.2%si, 0.0%st Cpu1 : 0.0%us, 0.8%sy, 0.0%ni, 93.0%id, 0.2%wa, 0.0%hi, 6.0%si, 0.0%st Cpu2 : 0.0%us, 0.6%sy, 0.0%ni, 94.4%id, 0.1%wa, 0.0%hi, 4.8%si, 0.0%st Cpu3 : 0.0%us, 7.5%sy, 0.0%ni, 36.3%id, 56.1%wa, 0.0%hi, 0.0%si, 0.0%st Cpu4 : 0.0%us, 1.3%sy, 0.0%ni, 85.7%id, 4.9%wa, 0.0%hi, 8.1%si, 0.0%st Cpu5 : 0.1%us, 5.5%sy, 0.0%ni, 36.2%id, 58.3%wa, 0.0%hi, 0.0%si, 0.0%st Cpu6 : 0.0%us, 5.0%sy, 0.0%ni, 36.3%id, 58.7%wa, 0.0%hi, 0.0%si, 0.0%st Cpu7 : 0.0%us, 5.1%sy, 0.0%ni, 36.3%id, 58.5%wa, 0.0%hi, 0.0%si, 0.0%st Cpu8 : 0.1%us, 8.3%sy, 0.0%ni, 27.2%id, 64.4%wa, 0.0%hi, 0.0%si, 0.0%st Cpu9 : 0.1%us, 7.9%sy, 0.0%ni, 36.2%id, 55.8%wa, 0.0%hi, 0.0%si, 0.0%st Cpu10 : 0.0%us, 7.8%sy, 0.0%ni, 36.2%id, 56.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu11 : 0.0%us, 7.3%sy, 0.0%ni, 36.3%id, 56.4%wa, 0.0%hi, 0.0%si, 0.0%st Cpu12 : 0.0%us, 5.6%sy, 0.0%ni, 33.1%id, 61.2%wa, 0.0%hi, 0.0%si, 0.0%st Cpu13 : 0.1%us, 5.3%sy, 0.0%ni, 36.1%id, 58.5%wa, 0.0%hi, 0.0%si, 0.0%st Cpu14 : 0.0%us, 4.9%sy, 0.0%ni, 36.4%id, 58.7%wa, 0.0%hi, 0.0%si, 0.0%st Cpu15 : 0.1%us, 5.4%sy, 0.0%ni, 36.5%id, 58.1%wa, 0.0%hi, 0.0%si, 0.0%st Given all this, the throughput reported by running "dstat 10" is in the range of 2200-2300 MB/sec. Given the math above I would expect something in the range of 2*1920 ~= 3600+ MB/sec. Does anybody have any idea where my missing bandwidth went? Thanks!

  Read the article

• Load-balancing between a Procurve switch and a server

  - by vlad

  Hello I've been searching around the web for this problem i've been having. It's similar in a way to this question: How exactly & specifically does layer 3 LACP destination address hashing work? My setup is as follows: I have a central switch, a Procurve 2510G-24, image version Y.11.16. It's the center of a star topology, there are four switches connected to it via a single gigabit link. Those switches service the users. On the central switch, I have a server with two gigabit interfaces that I want to bond together in order to achieve higher throughput, and two other servers that have single gigabit connections to the switch. The topology looks as follows: sw1 sw2 sw3 sw4 | | | | --------------------- | sw0 | --------------------- || | | srv1 srv2 srv3 The servers were running FreeBSD 8.1. On srv1 I set up a lagg interface using the lacp protocol, and on the switch I set up a trunk for the two ports using lacp as well. The switch showed that the server was a lacp partner, I could ping the server from another computer, and the server could ping other computers. If I unplugged one of the cables, the connection would keep working, so everything looked fine. Until I tested throughput. There was only one link used between srv1 and sw0. All testing was conducted with iperf, and load distribution was checked with systat -ifstat. I was looking to test the load balancing for both receive and send operations, as I want this server to be a file server. There were therefore two scenarios: iperf -s on srv1 and iperf -c on the other servers iperf -s on the other servers and iperf -c on srv1 connected to all the other servers. Every time only one link was used. If one cable was unplugged, the connections would keep going. However, once the cable was plugged back in, the load was not distributed. Each and every server is able to fill the gigabit link. In one-to-one test scenarios, iperf was reporting around 940Mbps. The CPU usage was around 20%, which means that the servers could withstand a doubling of the throughput. srv1 is a dell poweredge sc1425 with onboard intel 82541GI nics (em driver on freebsd). After troubleshooting a previous problem with vlan tagging on top of a lagg interface, it turned out that the em could not support this. So I figured that maybe something else is wrong with the em drivers and / or lagg stack, so I started up backtrack 4r2 on this same server. So srv1 now uses linux kernel 2.6.35.8. I set up a bonding interface bond0. The kernel module was loaded with option mode=4 in order to get lacp. The switch was happy with the link, I could ping to and from the server. I could even put vlans on top of the bonding interface. However, only half the problem was solved: if I used srv1 as a client to the other servers, iperf was reporting around 940Mbps for each connection, and bwm-ng showed, of course, a nice distribution of the load between the two nics; if I run the iperf server on srv1 and tried to connect with the other servers, there was no load balancing. I thought that maybe I was out of luck and the hashes for the two mac addresses of the clients were the same, so I brought in two new servers and tested with the four of them at the same time, and still nothing changed. I tried disabling and reenabling one of the links, and all that happened was the traffic switched from one link to the other and back to the first again. I also tried setting the trunk to "plain trunk mode" on the switch, and experimented with other bonding modes (roundrobin, xor, alb, tlb) but I never saw any traffic distribution. One interesting thing, though: one of the four switches is a Cisco 2950, image version 12.1(22)EA7. It has 48 10/100 ports and 2 gigabit uplinks. I have a server (call it srv4) with a 4 channel trunk connected to it (4x100), FreeBSD 8.0 release. The switch is connected to sw0 via gigabit. If I set up an iperf server on one of the servers connected to sw0 and a client on srv4, ALL 4 links are used, and iperf reports around 330Mbps. systat -ifstat shows all four interfaces are used. The cisco port-channel uses src-mac to balance the load. The HP should use both the source and destination according to the manual, so it should work as well. Could this mean there is some bug in the HP firmware? Am I doing something wrong?

  Read the article

• VSFTPD Unable to set write permissions on folder

  - by Frank Astin

  I've just set up my first FTP server with VSFTPD on cent os . I can connect to it fine using a user in the group ftp-users but I get read only access . I've tried several different CHMOD codes on the folder (even 777) all to no avail . This is the tutorial I used to set up the server http://tinyurl.com/73pyuxz hopefully you'll be able to see something I missed. Thanks in advance . Requested Config File : # Example config file /etc/vsftpd/vsftpd.conf # # The default compiled in settings are fairly paranoid. This sample file # loosens things up a bit, to make the ftp daemon more usable. # Please see vsftpd.conf.5 for all compiled in defaults. # # READ THIS: This example file is NOT an exhaustive list of vsftpd options. # Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's # capabilities. # # Allow anonymous FTP? (Beware - allowed by default if you comment this out). anonymous_enable=NO # # Uncomment this to allow local users to log in. local_enable=YES # # Uncomment this to enable any form of FTP write command. write_enable=YES # # Default umask for local users is 077. You may wish to change this to 022, # if your users expect that (022 is used by most other ftpd's) local_umask=022 # # Uncomment this to allow the anonymous FTP user to upload files. This only # has an effect if the above global write enable is activated. Also, you will # obviously need to create a directory writable by the FTP user. #anon_upload_enable=YES # # Uncomment this if you want the anonymous FTP user to be able to create # new directories. #anon_mkdir_write_enable=YES # # Activate directory messages - messages given to remote users when they # go into a certain directory. dirmessage_enable=YES # # The target log file can be vsftpd_log_file or xferlog_file. # This depends on setting xferlog_std_format parameter xferlog_enable=YES # # Make sure PORT transfer connections originate from port 20 (ftp-data). connect_from_port_20=YES # # If you want, you can arrange for uploaded anonymous files to be owned by # a different user. Note! Using "root" for uploaded files is not # recommended! #chown_uploads=YES #chown_username=whoever # # The name of log file when xferlog_enable=YES and xferlog_std_format=YES # WARNING - changing this filename affects /etc/logrotate.d/vsftpd.log #xferlog_file=/var/log/xferlog # # Switches between logging into vsftpd_log_file and xferlog_file files. # NO writes to vsftpd_log_file, YES to xferlog_file xferlog_std_format=YES # # You may change the default value for timing out an idle session. #idle_session_timeout=600 # # You may change the default value for timing out a data connection. #data_connection_timeout=120 # # It is recommended that you define on your system a unique user which the # ftp server can use as a totally isolated and unprivileged user. #nopriv_user=ftpsecure # # Enable this and the server will recognise asynchronous ABOR requests. Not # recommended for security (the code is non-trivial). Not enabling it, # however, may confuse older FTP clients. #async_abor_enable=YES # # By default the server will pretend to allow ASCII mode but in fact ignore # the request. Turn on the below options to have the server actually do ASCII # mangling on files when in ASCII mode. # Beware that on some FTP servers, ASCII support allows a denial of service # attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd # predicted this attack and has always been safe, reporting the size of the # raw file. # ASCII mangling is a horrible feature of the protocol. #ascii_upload_enable=YES #ascii_download_enable=YES # # You may fully customise the login banner string: #ftpd_banner=Welcome to blah FTP service. # # You may specify a file of disallowed anonymous e-mail addresses. Apparently # useful for combatting certain DoS attacks. #deny_email_enable=YES # (default follows) #banned_email_file=/etc/vsftpd/banned_emails # # You may specify an explicit list of local users to chroot() to their home # directory. If chroot_local_user is YES, then this list becomes a list of # users to NOT chroot(). #chroot_list_enable=YES # (default follows) #chroot_list_file=/etc/vsftpd/chroot_list # # You may activate the "-R" option to the builtin ls. This is disabled by # default to avoid remote users being able to cause excessive I/O on large # sites. However, some broken FTP clients such as "ncftp" and "mirror" assume # the presence of the "-R" option, so there is a strong case for enabling it. #ls_recurse_enable=YES # # When "listen" directive is enabled, vsftpd runs in standalone mode and # listens on IPv4 sockets. This directive cannot be used in conjunction # with the listen_ipv6 directive. listen=YES # # This directive enables listening on IPv6 sockets. To listen on IPv4 and IPv6 # sockets, you must run two copies of vsftpd whith two configuration files. # Make sure, that one of the listen options is commented !! #listen_ipv6=YES pam_service_name=vsftpd userlist_enable=YES tcp_wrappers=YES

  Read the article

• vsftpd not allowing uploads. 550 response

  - by Josh

  I've set vsftpd up on a centos box. I keep trying to upload files but I keep getting "550 Failed to change directory" and "550 Could not get file size." Here's my vsftpd.conf # The default compiled in settings are fairly paranoid. This sample file # loosens things up a bit, to make the ftp daemon more usable. # Please see vsftpd.conf.5 for all compiled in defaults. # # READ THIS: This example file is NOT an exhaustive list of vsftpd options. # Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's # capabilities. # # Allow anonymous FTP? (Beware - allowed by default if you comment this out). anonymous_enable=YES # # Uncomment this to allow local users to log in. local_enable=YES # # Uncomment this to enable any form of FTP write command. write_enable=YES # # Default umask for local users is 077. You may wish to change this to 022, # if your users expect that (022 is used by most other ftpd's) local_umask=022 # # Uncomment this to allow the anonymous FTP user to upload files. This only # has an effect if the above global write enable is activated. Also, you will # obviously need to create a directory writable by the FTP user. anon_upload_enable=YES # # Uncomment this if you want the anonymous FTP user to be able to create # new directories. anon_mkdir_write_enable=YES anon_other_write_enable=YES # # Activate directory messages - messages given to remote users when they # go into a certain directory. dirmessage_enable=YES # # The target log file can be vsftpd_log_file or xferlog_file. # This depends on setting xferlog_std_format parameter xferlog_enable=YES # # Make sure PORT transfer connections originate from port 20 (ftp-data). connect_from_port_20=YES # # If you want, you can arrange for uploaded anonymous files to be owned by # a different user. Note! Using "root" for uploaded files is not # recommended! #chown_uploads=YES #chown_username=whoever # # The name of log file when xferlog_enable=YES and xferlog_std_format=YES # WARNING - changing this filename affects /etc/logrotate.d/vsftpd.log #xferlog_file=/var/log/xferlog # # Switches between logging into vsftpd_log_file and xferlog_file files. # NO writes to vsftpd_log_file, YES to xferlog_file xferlog_std_format=NO # # You may change the default value for timing out an idle session. #idle_session_timeout=600 # # You may change the default value for timing out a data connection. #data_connection_timeout=120 # # It is recommended that you define on your system a unique user which the # ftp server can use as a totally isolated and unprivileged user. #nopriv_user=ftpsecure # # Enable this and the server will recognise asynchronous ABOR requests. Not # recommended for security (the code is non-trivial). Not enabling it, # however, may confuse older FTP clients. #async_abor_enable=YES # # By default the server will pretend to allow ASCII mode but in fact ignore # the request. Turn on the below options to have the server actually do ASCII # mangling on files when in ASCII mode. # Beware that on some FTP servers, ASCII support allows a denial of service # attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd # predicted this attack and has always been safe, reporting the size of the # raw file. # ASCII mangling is a horrible feature of the protocol. #ascii_upload_enable=YES #ascii_download_enable=YES # # You may fully customise the login banner string: #ftpd_banner=Welcome to blah FTP service. # # You may specify a file of disallowed anonymous e-mail addresses. Apparently # useful for combatting certain DoS attacks. #deny_email_enable=YES # (default follows) #banned_email_file=/etc/vsftpd/banned_emails # # You may specify an explicit list of local users to chroot() to their home # directory. If chroot_local_user is YES, then this list becomes a list of # users to NOT chroot(). #chroot_list_enable=YES # (default follows) #chroot_list_file=/etc/vsftpd/chroot_list # # You may activate the "-R" option to the builtin ls. This is disabled by # default to avoid remote users being able to cause excessive I/O on large # sites. However, some broken FTP clients such as "ncftp" and "mirror" assume # the presence of the "-R" option, so there is a strong case for enabling it. #ls_recurse_enable=YES # # When "listen" directive is enabled, vsftpd runs in standalone mode and # listens on IPv4 sockets. This directive cannot be used in conjunction # with the listen_ipv6 directive. listen=YES # This directive enables listening on IPv6 sockets. To listen on IPv4 and IPv6 # sockets, you must run two copies of vsftpd whith two configuration files. # Make sure, that one of the listen options is commented !! #listen_ipv6=YES pam_service_name=vsftpd userlist_enable=YES tcp_wrappers=YES log_ftp_protocol=YES banner_file=/etc/vsftpd/issue local_root=/var/www guest_enable=YES guest_username=ftpusr ftp_username=nobody

  Read the article

• Centos 6.3 vsftp unable to upload file to apache webserver

  - by user148648

  I am new to Centos, I did work with Sun Solaris and upload files to Apache web server before. I create an end user account and manage to ftp using command prompt to the server, error message is '226 Transfer Done (but failed to open directory). Content of my vsftpd.conf as below # Example config file /etc/vsftpd/vsftpd.conf # # The default compiled in settings are fairly paranoid. This sample file # loosens things up a bit, to make the ftp daemon more usable. # Please see vsftpd.conf.5 for all compiled in defaults. # # READ THIS: This example file is NOT an exhaustive list of vsftpd options. # Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's # capabilities. # # Allow anonymous FTP? (Beware - allowed by default if you comment this out). anonymous_enable=YES # ** may need to comment it back # # Uncomment this to allow local users to log in. local_enable=YES # # Uncomment this to enable any form of FTP write command. write_enable=YES # # Default umask for local users is 077. You may wish to change this to 022, # if your users expect that (022 is used by most other ftpd's) #local_umask=022 local_umask=077 # # Uncomment this to allow the anonymous FTP user to upload files. This only # has an effect if the above global write enable is activated. Also, you will # obviously need to create a directory writable by the FTP user. anon_upload_enable=YES # *** maybe to comment it back!!! # # Uncomment this if you want the anonymous FTP user to be able to create # new directories. anon_mkdir_write_enable=YES # ** may need to comment it back!!! # # Activate directory messages - messages given to remote users when they # go into a certain directory. dirmessage_enable=YES # # The target log file can be vsftpd_log_file or xferlog_file. # This depends on setting xferlog_std_format parameter xferlog_enable=YES # # Make sure PORT transfer connections originate from port 20 (ftp-data). connect_from_port_20=YES # # If you want, you can arrange for uploaded anonymous files to be owned by # a different user. Note! Using "root" for uploaded files is not # recommended! #chown_uploads=YES #chown_username=whoever # # The name of log file when xferlog_enable=YES and xferlog_std_format=YES # WARNING - changing this filename affects /etc/logrotate.d/vsftpd.log xferlog_file=/var/log/xferlog # # Switches between logging into vsftpd_log_file and xferlog_file files. # NO writes to vsftpd_log_file, YES to xferlog_file xferlog_std_format=YES # # You may change the default value for timing out an idle session. #idle_session_timeout=600 # # You may change the default value for timing out a data connection. #data_connection_timeout=120 # # It is recommended that you define on your system a unique user which the # ftp server can use as a totally isolated and unprivileged user. #nopriv_user=ftpsecure # # Enable this and the server will recognise asynchronous ABOR requests. Not # recommended for security (the code is non-trivial). Not enabling it, # however, may confuse older FTP clients. #async_abor_enable=YES # # By default the server will pretend to allow ASCII mode but in fact ignore # the request. Turn on the below options to have the server actually do ASCII # mangling on files when in ASCII mode. # Beware that on some FTP servers, ASCII support allows a denial of service # attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd # predicted this attack and has always been safe, reporting the size of the # raw file. # ASCII mangling is a horrible feature of the protocol. ascii_upload_enable=YES ascii_download_enable=YES # # You may fully customise the login banner string: ftpd_banner=Warning, only for authorize login. # # You may specify a file of disallowed anonymous e-mail addresses. Apparently # useful for combatting certain DoS attacks. #deny_email_enable=YES # (default follows) #banned_email_file=/etc/vsftpd/banned_emails # # You may specify an explicit list of local users to chroot() to their home # directory. If chroot_local_user is YES, then this list becomes a list of # users to NOT chroot(). chroot_local_user=YES chroot_list_enable=YES # (default follows) #chroot_list_file=/etc/vsftpd/chroot_list local_root=/var/www # # You may activate the "-R" option to the builtin ls. This is disabled by # default to avoid remote users being able to cause excessive I/O on large # sites. However, some broken FTP clients such as "ncftp" and "mirror" assume # the presence of the "-R" option, so there is a strong case for enabling it. ls_recurse_enable=YES # # When "listen" directive is enabled, vsftpd runs in standalone mode and # listens on IPv4 sockets. This directive cannot be used in conjunction # with the listen_ipv6 directive. listen=YES # # This directive enables listening on IPv6 sockets. To listen on IPv4 and IPv6 # sockets, you must run two copies of vsftpd with two configuration files. # Make sure, that one of the listen options is commented !! #listen_ipv6=YES pam_service_name=vsftpd userlist_enable=YES tcp_wrappers=YES

  Read the article

• postfix 5.7.1 Relay access denied when sending mail with cron

  - by zensys

  Reluctant to ask because there is so much here about 'postfix relay access denied' but I cannot find my case: I use php (Zend Framework) to send emails outside my network using the Google mail server because I could not send mail outside my server (user: web). However when I sent out an email via cron (user: root, I believe), still using ZF, using the same mail config/credentials, I get the message: '5.7.1 Relay access denied' I guess I need to know one of two things: 1. How can I use the google smtp server from cron 2. What do I need to change in my config to send mail using my own server instead of google Though the answer to 2. is the more structural solution I assume, I am quite happy with an answer to 1. as well because I think Google is better at server maintaince (security/spam) than I am. Below my ZF application.ini mail section, main.cf and master.cf: application.ini: resources.mail.transport.type = smtp resources.mail.transport.auth = login resources.mail.transport.host = "smtp.gmail.com" resources.mail.transport.ssl = tls resources.mail.transport.port = 587 resources.mail.transport.username = [email protected] resources.mail.transport.password = xxxxxxx resources.mail.defaultFrom.email = [email protected] resources.mail.defaultFrom.name = "my company" main.cf: # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. #myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = /usr/share/doc/postfix # TLS parameters smtpd_tls_cert_file = /etc/postfix/smtpd.cert smtpd_tls_key_file = /etc/postfix/smtpd.key smtpd_use_tls = yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. myhostname = mail.second-start.nl mydomain = second-start.nl alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = relayhost = mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mailbox_command = procmail -a "$EXTENSION" mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all html_directory = /usr/share/doc/postfix/html message_size_limit = 30720000 virtual_alias_domains = virtual_alias_maps = proxy:mysql:/etc/postfix/mysql-virtual_forwardings.cf, mysql:/etc/postfix/mysql-virtual_email2email.cf virtual_mailbox_domains = proxy:mysql:/etc/postfix/mysql-virtual_domains.cf virtual_mailbox_maps = proxy:mysql:/etc/postfix/mysql-virtual_mailboxes.cf virtual_mailbox_base = /home/vmail virtual_uid_maps = static:5000 virtual_gid_maps = static:5000 smtpd_sasl_auth_enable = yes broken_sasl_auth_clients = yes smtpd_sasl_authenticated_header = yes # see under Spam smtpd_recipient_restrictions = permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination proxy_read_maps = $local_recipient_maps $mydestination $virtual_alias_maps $virtual_alias_domains $virtual_mailbox_maps $virtual_mailbox_domains $relay_recipient_maps $relay_domains $canonical_maps $sender_canonical_maps $recipient_canonical_maps $relocated_maps $transport_maps $mynetworks $virtual_mailbox_limit_maps virtual_transport = dovecot dovecot_destination_recipient_limit = 1 # Spam disable_vrfy_command = yes smtpd_delay_reject = yes smtpd_helo_required = yes smtpd_helo_restrictions = permit_mynetworks, check_helo_access hash:/etc/postfix/helo_access, reject_non_fqdn_hostname, reject_invalid_hostname, permit smtpd_recipient_restrictions = permit_sasl_authenticated, reject_unauth_destination, reject_invalid_hostname, reject_non_fqdn_sender, reject_non_fqdn_recipient, reject_unknown_sender_domain, reject_unknown_recipient_domain, permit_mynetworks, reject_non_fqdn_hostname, reject_rbl_client sbl.spamhaus.org, reject_rbl_client zen.spamhaus.org, reject_rbl_client cbl.abuseat.org, reject_rbl_client bl.spamcop.net, permit smtpd_error_sleep_time = 1s smtpd_soft_error_limit = 10 smtpd_hard_error_limit = 20 master.cf: # ========================================================================== # service type private unpriv chroot wakeup maxproc command + args # (yes) (yes) (yes) (never) (100) # ========================================================================== smtp inet n - - - - smtpd #smtp inet n - - - 1 postscreen #smtpd pass - - - - - smtpd #dnsblog unix - - - - 0 dnsblog #tlsproxy unix - - - - 0 tlsproxy #submission inet n - - - - smtpd # -o smtpd_tls_security_level=encrypt # -o smtpd_sasl_auth_enable=yes # -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING #smtps inet n - - - - smtpd # -o smtpd_tls_wrappermode=yes # -o smtpd_sasl_auth_enable=yes # -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING #628 inet n - - - - qmqpd pickup fifo n - - 60 1 pickup cleanup unix n - - - 0 cleanup qmgr fifo n - n 300 1 qmgr #qmgr fifo n - - 300 1 oqmgr tlsmgr unix - - - 1000? 1 tlsmgr rewrite unix - - - - - trivial-rewrite bounce unix - - - - 0 bounce defer unix - - - - 0 bounce trace unix - - - - 0 bounce verify unix - - - - 1 verify flush unix n - - 1000? 0 flush proxymap unix - - n - - proxymap proxywrite unix - - n - 1 proxymap smtp unix - - - - - smtp # When relaying mail as backup MX, disable fallback_relay to avoid MX loops relay unix - - - - - smtp -o smtp_fallback_relay= # -o smtp_helo_timeout=5 -o smtp_connect_timeout=5 showq unix n - - - - showq error unix - - - - - error retry unix - - - - - error discard unix - - - - - discard local unix - n n - - local virtual unix - n n - - virtual lmtp unix - - - - - lmtp anvil unix - - - - 1 anvil scache unix - - - - 1 scache # # ==================================================================== # Interfaces to non-Postfix software. Be sure to examine the manual # pages of the non-Postfix software to find out what options it wants. # # Many of the following services use the Postfix pipe(8) delivery # agent. See the pipe(8) man page for information about ${recipient} # and other message envelope options. # ==================================================================== # # maildrop. See the Postfix MAILDROP_README file for details. # Also specify in main.cf: maildrop_destination_recipient_limit=1 # maildrop unix - n n - - pipe flags=DRhu user=vmail argv=/usr/bin/maildrop -d ${recipient} # # ==================================================================== # # Recent Cyrus versions can use the existing "lmtp" master.cf entry. # # Specify in cyrus.conf: # lmtp cmd="lmtpd -a" listen="localhost:lmtp" proto=tcp4 # # Specify in main.cf one or more of the following: # mailbox_transport = lmtp:inet:localhost # virtual_transport = lmtp:inet:localhost # # ==================================================================== # # Cyrus 2.1.5 (Amos Gouaux) # Also specify in main.cf: cyrus_destination_recipient_limit=1 # #cyrus unix - n n - - pipe # user=cyrus argv=/cyrus/bin/deliver -e -r ${sender} -m ${extension} ${user} # # ==================================================================== # Old example of delivery via Cyrus. # #old-cyrus unix - n n - - pipe # flags=R user=cyrus argv=/cyrus/bin/deliver -e -m ${extension} ${user} # # ==================================================================== # # See the Postfix UUCP_README file for configuration details. # uucp unix - n n - - pipe flags=Fqhu user=uucp argv=uux -r -n -z -a$sender - $nexthop!rmail ($recipient) # # Other external delivery methods. # ifmail unix - n n - - pipe flags=F user=ftn argv=/usr/lib/ifmail/ifmail -r $nexthop ($recipient) bsmtp unix - n n - - pipe flags=Fq. user=bsmtp argv=/usr/lib/bsmtp/bsmtp -t$nexthop -f$sender $recipient scalemail-backend unix - n n - 2 pipe flags=R user=scalemail argv=/usr/lib/scalemail/bin/scalemail-store ${nexthop} ${user} ${extension} mailman unix - n n - - pipe flags=FR user=list argv=/usr/lib/mailman/bin/postfix-to-mailman.py ${nexthop} ${user} dovecot unix - n n - - pipe flags=DRhu user=vmail:vmail argv=/usr/lib/dovecot/deliver -d ${recipient}

  Read the article

• Trouble recovering MySQL InnoDB database after server crash

  - by Andy Shinn

  I had a server crash due to a broken iSCSI link (the filesystem went into read-only mode). After repairing the link and rebooting the machine (CentOS 5 / MySQL 5.1), the MySQL server would not start and gave the following error: 100603 19:11:46 mysqld_safe Starting mysqld daemon with databases from /var/lib/mysql InnoDB: The log sequence number in ibdata files does not match InnoDB: the log sequence number in the ib_logfiles! 100603 19:11:46 InnoDB: Database was not shut down normally! InnoDB: Starting crash recovery. InnoDB: Reading tablespace information from the .ibd files... InnoDB: Restoring possible half-written data pages from the doublewrite InnoDB: buffer... InnoDB: Warning: database page corruption or a failed InnoDB: file read of page 112541. InnoDB: Trying to recover it from the doublewrite buffer. InnoDB: Dump of the page: 100603 19:11:46 InnoDB: Page dump in ascii and hex (16384 bytes): lots of binary data 100603 19:11:46 InnoDB: Page checksum 953720272, prior-to-4.0.14-form checksum 2641912043 InnoDB: stored checksum 617821918, prior-to-4.0.14-form stored checksum 2080617765 InnoDB: Page lsn 115 2632899642, low 4 bytes of lsn at page end 2641594600 InnoDB: Page number (if stored to page already) 112541, InnoDB: space id (if created with = MySQL-4.1.1 and stored already) 0 InnoDB: Page may be an index page where index id is 0 616 InnoDB: Dump of corresponding page in doublewrite buffer: 100603 19:11:46 InnoDB: Page dump in ascii and hex (16384 bytes): more binary data 100603 19:11:46 InnoDB: Page checksum 908374788, prior-to-4.0.14-form checksum 824841363 InnoDB: stored checksum 912869634, prior-to-4.0.14-form stored checksum 2210927931 InnoDB: Page lsn 115 2635312169, low 4 bytes of lsn at page end 2633173354 InnoDB: Page number (if stored to page already) 112541, InnoDB: space id (if created with = MySQL-4.1.1 and stored already) 0 InnoDB: Page may be an index page where index id is 0 616 InnoDB: Also the page in the doublewrite buffer is corrupt. InnoDB: Cannot continue operation. InnoDB: You can try to recover the database with the my.cnf InnoDB: option: InnoDB: innodb_force_recovery=6 100603 19:11:46 mysqld_safe mysqld from pid file /var/run/mysqld/mysqld.pid ended Per the error message, I have tried setting set-variable=innodb_force_recovery=6 in the my.cnf to get to the data. This allows the MySQL server to start. But when I try to do a mysqldump of the database or a SELECT * INTO OUTFILE "filename" FROM broken_table; it seems to endlessly just export the same line over and over again. I have also tried http://code.google.com/p/innodb-tools/. But this tool fails with an error that 'blob' type is not supported. If I try to access the data using the PHP application it crashes MySQL: `100603 19:19:19 - mysqld got signal 11 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=8384512 read_buffer_size=131072 max_used_connections=2 max_threads=151 threads_connected=2 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 338317 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd: 0x15d33f0 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 0x453aff00 thread_stack 0x40000 /usr/libexec/mysqld(my_print_stacktrace+0x24) [0x874364] /usr/libexec/mysqld(handle_segfault+0x346) [0x5c9166] /lib64/libpthread.so.0 [0x3a6e40eb10] /usr/libexec/mysqld(rec_get_offsets_func+0x30) [0x7cc310] /usr/libexec/mysqld [0x7674d8] /usr/libexec/mysqld(btr_search_info_update_slow+0x638) [0x768d48] /usr/libexec/mysqld(btr_cur_search_to_nth_level+0xc7d) [0x75f86d] /usr/libexec/mysqld [0x7dd1c1] /usr/libexec/mysqld(row_search_for_mysql+0x18b0) [0x7e03d0] /usr/libexec/mysqld(ha_innobase::general_fetch(unsigned char*, unsigned int, unsigned int)+0x7c) [0x7526fc] /usr/libexec/mysqld(handler::read_multi_range_next(st_key_multi_range**)+0x29) [0x6aed09] /usr/libexec/mysqld(QUICK_RANGE_SELECT::get_next()+0x194) [0x69a964] /usr/libexec/mysqld [0x6aafe9] /usr/libexec/mysqld(sub_select(JOIN*, st_join_table*, bool)+0x56) [0x635196] /usr/libexec/mysqld [0x63f9cd] /usr/libexec/mysqld(JOIN::exec()+0x950) [0x6497c0] /usr/libexec/mysqld(mysql_select(THD*, Item*, TABLE_LIST*, unsigned int, List&, Item*, unsigned int, st_order*, st_order*, Item*, st_order*, unsign ed long long, select_result*, st_select_lex_unit*, st_select_lex*)+0x17b) [0x64b34b] /usr/libexec/mysqld(handle_select(THD*, st_lex*, select_result*, unsigned long)+0x169) [0x64bc79] /usr/libexec/mysqld [0x5d34b6] /usr/libexec/mysqld(mysql_execute_command(THD*)+0x4e5) [0x5d6b45] /usr/libexec/mysqld(mysql_parse(THD*, char const*, unsigned int, char const)+0x211) [0x5dc321] /usr/libexec/mysqld(dispatch_command(enum_server_command, THD*, char*, unsigned int)+0x10b8) [0x5dd3f8] /usr/libexec/mysqld(do_command(THD*)+0xe6) [0x5dd9e6] /usr/libexec/mysqld(handle_one_connection+0x73d) [0x5d036d] /lib64/libpthread.so.0 [0x3a6e40673d] /lib64/libc.so.6(clone+0x6d) [0x3a6d4d3d1d] Trying to get some variables. Some pointers may be invalid and cause the dump to abort... thd-query at 0x15de5e0 = SELECT DISTINCT count(DISTINCT i.itemid) as rowscount,i.hostid FROM items i WHERE ((i.itemid BETWEEN 000000000000000 AND 0999999 99999999)) AND i.type<9 AND (i.hostid IN (10017,10047,10050,10054,10056,10059,10062,10063,10064,10065,10066,10067,10068,10069,10070,10071,10072,10073,100 74,10075,10076,10077,10078,10079,10080,10081,10082,10084,10088,10089,10090,10091,10092,10093,10094,10095,10096,10097,10098,10099,10100,10101,10102,10103,10 104,10105,10106,10107,10108,10109)) GROUP BY i.hostid thd-thread_id=3 thd-killed=NOT_KILLED The manual page at contains information that should help you find out what is causing the crash. 100603 19:19:19 mysqld_safe Number of processes running now: 0 100603 19:19:19 mysqld_safe mysqld restarted` Before recovering form an older backup as a last resort I am looking for anymore suggestions. Thanks!

  Read the article

• vsftpd not allowing uploads. 550 response.

  - by Josh

  I've set vsftpd up on a centos box. I keep trying to upload files but I keep getting "550 Failed to change directory" and "550 Could not get file size." Here's my vsftpd.conf # The default compiled in settings are fairly paranoid. This sample file # loosens things up a bit, to make the ftp daemon more usable. # Please see vsftpd.conf.5 for all compiled in defaults. # # READ THIS: This example file is NOT an exhaustive list of vsftpd options. # Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's # capabilities. # # Allow anonymous FTP? (Beware - allowed by default if you comment this out). anonymous_enable=YES # # Uncomment this to allow local users to log in. local_enable=YES # # Uncomment this to enable any form of FTP write command. write_enable=YES # # Default umask for local users is 077. You may wish to change this to 022, # if your users expect that (022 is used by most other ftpd's) local_umask=022 # # Uncomment this to allow the anonymous FTP user to upload files. This only # has an effect if the above global write enable is activated. Also, you will # obviously need to create a directory writable by the FTP user. anon_upload_enable=YES # # Uncomment this if you want the anonymous FTP user to be able to create # new directories. anon_mkdir_write_enable=YES anon_other_write_enable=YES # # Activate directory messages - messages given to remote users when they # go into a certain directory. dirmessage_enable=YES # # The target log file can be vsftpd_log_file or xferlog_file. # This depends on setting xferlog_std_format parameter xferlog_enable=YES # # Make sure PORT transfer connections originate from port 20 (ftp-data). connect_from_port_20=YES # # If you want, you can arrange for uploaded anonymous files to be owned by # a different user. Note! Using "root" for uploaded files is not # recommended! #chown_uploads=YES #chown_username=whoever # # The name of log file when xferlog_enable=YES and xferlog_std_format=YES # WARNING - changing this filename affects /etc/logrotate.d/vsftpd.log #xferlog_file=/var/log/xferlog # # Switches between logging into vsftpd_log_file and xferlog_file files. # NO writes to vsftpd_log_file, YES to xferlog_file xferlog_std_format=NO # # You may change the default value for timing out an idle session. #idle_session_timeout=600 # # You may change the default value for timing out a data connection. #data_connection_timeout=120 # # It is recommended that you define on your system a unique user which the # ftp server can use as a totally isolated and unprivileged user. #nopriv_user=ftpsecure # # Enable this and the server will recognise asynchronous ABOR requests. Not # recommended for security (the code is non-trivial). Not enabling it, # however, may confuse older FTP clients. #async_abor_enable=YES # # By default the server will pretend to allow ASCII mode but in fact ignore # the request. Turn on the below options to have the server actually do ASCII # mangling on files when in ASCII mode. # Beware that on some FTP servers, ASCII support allows a denial of service # attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd # predicted this attack and has always been safe, reporting the size of the # raw file. # ASCII mangling is a horrible feature of the protocol. #ascii_upload_enable=YES #ascii_download_enable=YES # # You may fully customise the login banner string: #ftpd_banner=Welcome to blah FTP service. # # You may specify a file of disallowed anonymous e-mail addresses. Apparently # useful for combatting certain DoS attacks. #deny_email_enable=YES # (default follows) #banned_email_file=/etc/vsftpd/banned_emails # # You may specify an explicit list of local users to chroot() to their home # directory. If chroot_local_user is YES, then this list becomes a list of # users to NOT chroot(). #chroot_list_enable=YES # (default follows) #chroot_list_file=/etc/vsftpd/chroot_list # # You may activate the "-R" option to the builtin ls. This is disabled by # default to avoid remote users being able to cause excessive I/O on large # sites. However, some broken FTP clients such as "ncftp" and "mirror" assume # the presence of the "-R" option, so there is a strong case for enabling it. #ls_recurse_enable=YES # # When "listen" directive is enabled, vsftpd runs in standalone mode and # listens on IPv4 sockets. This directive cannot be used in conjunction # with the listen_ipv6 directive. listen=YES # This directive enables listening on IPv6 sockets. To listen on IPv4 and IPv6 # sockets, you must run two copies of vsftpd whith two configuration files. # Make sure, that one of the listen options is commented !! #listen_ipv6=YES pam_service_name=vsftpd userlist_enable=YES tcp_wrappers=YES log_ftp_protocol=YES banner_file=/etc/vsftpd/issue local_root=/var/www guest_enable=YES guest_username=ftpusr ftp_username=nobody

  Read the article

• How to set up port forwarding and firewall settings for torrents using Transmsission on Mac OSX 10.5

  - by Liz

  I have picked up bits of advice here and there on the internet and got someway through this tortuous exercise (after it took 18 hours to download the first torrent I tried yesterday - magnet-link for a film). Where I have got stuck is with configuring the firewall on the Netgear Router but I am not sure if I have caused the problem myself by something else I have done configuring the Mac System Preferences for Security or Networking. I have been following the sections of these instructions that seem to apply, although they are written for a different OSX version (don't know which one, but the screen shots do not match what I see) and I am not wanting to set up my Mac as a server and attending to the parts that apply to port forwarding for Netgear rather than LinkSys: http://homepage.mac.com/car1son/static_port_fwd_intro.html I have been trying to follow these instructions: Instructions for DG834, DG834G, DG824M, FR114W, FM114P, FR114P, FR328S, FVL328, FVS328, FVS338, FVX538, FWAG114, FWG114P, or FVS318v3 These routers do port forwarding by assigning port numbers to a "service" associated with the application you want to run. "Rules" are set for particular services. Rules block or allow access, based on various conditions such as the time of day and the name of the service. To Create a New Inbound or Outbound Rule 1. Submit the router's address in an Internet browser. (The default is 192.168.0.1). 2. Enter the router's username and password. 3. From the main menu, click Security > Rules. 4. Click Add for inbound or outbound traffic, as appropriate to the application you are planning to run. 5. Select the Service. The services the router knows about are listed in the drop down. If the service you want is not listed, add it as described in the next section. 6. Select the Action, for example ALLOW always. 7. For Send to LAN Server, enter the IP address of the local server. Note that this is also the IP address the computers on your LAN will access. 8. For WAN User choose Any, or limit access to particular IP addresses. 9. For Log selection it is reasonable to turn logs on, especially at the beginning when you are unsure of the result of the changes you are making. Later, you may want to set logs to "Never" for performance reasons. 10. Click Apply. As noted in user manual for some models: * Consider using the Dynamic DNS feature on the Advanced menu, so that external users can find your network when the DHCP lease is renewed by your ISP. * If your own LAN server uses DHCP, and your IPs change on rebooting, consider using the Reserved IP Address feature in the LAN IP menu. To Add a Service for These Routers 1. Click Security > Services > Add Custom Service. 2. Enter any name you choose for the service. 3. Select whether the service is to use TCP or UDP. If you are unsure, select both. 4. Enter the lowest port number used by the service. 5. Enter the highest port number used. If the service uses only one port number, enter the same number. 6. Click Apply. There is no "Security - Rules" submenu in the Netgear page, so I have been trying to access "Security - Firewall Rules". I can access everthing else in the Netgear settings as Admin but I cannot get the "Firewall Rules" section to open up. (I am not 100% sure I will know exactly what to do if and when I do get it opened up!) I haven't managed to find though searching the internet any instructions that would seem to apply specifically to what I am trying to achieve, so would be very grateful if someone could either point me in the right direction or give me some advice directly. Best wishes, Liz

  Read the article

• fd partitions gone from 2 discs, md happy with it and resyncs. How to recover ?

  - by d0nd

  Hey gurus, need some help badly with this one. I run a server with a 6Tb md raid5 volume built over 7*1Tb disks. I've had to shut down the server lately and when it went back up, 2 out of the 7 disks used for the raid volume had lost its conf : dmesg : [ 10.184167] sda: sda1 sda2 sda3 // System disk [ 10.202072] sdb: sdb1 [ 10.210073] sdc: sdc1 [ 10.222073] sdd: sdd1 [ 10.229330] sde: sde1 [ 10.239449] sdf: sdf1 [ 11.099896] sdg: unknown partition table [ 11.255641] sdh: unknown partition table All 7 disks have same geometry and were configured alike : dmesg : Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x1e7481a5 Device Boot Start End Blocks Id System /dev/sdb1 1 121601 976760001 fd Linux raid autodetect All 7 disks (sdb1, sdc1, sdd1, sde1, sdf1, sdg1, sdh1) were used in a md raid5 xfs volume. When booting, md, which was (obviously) out of sync kicked in and automatically started rebuilding over the 7 disks, including the two "faulty" ones; xfs tried to do some shenanigans as well: dmesg : [ 19.566941] md: md0 stopped. [ 19.817038] md: bind<sdc1> [ 19.817339] md: bind<sdd1> [ 19.817465] md: bind<sde1> [ 19.817739] md: bind<sdf1> [ 19.817917] md: bind<sdh> [ 19.818079] md: bind<sdg> [ 19.818198] md: bind<sdb1> [ 19.818248] md: md0: raid array is not clean -- starting background reconstruction [ 19.825259] raid5: device sdb1 operational as raid disk 0 [ 19.825261] raid5: device sdg operational as raid disk 6 [ 19.825262] raid5: device sdh operational as raid disk 5 [ 19.825264] raid5: device sdf1 operational as raid disk 4 [ 19.825265] raid5: device sde1 operational as raid disk 3 [ 19.825267] raid5: device sdd1 operational as raid disk 2 [ 19.825268] raid5: device sdc1 operational as raid disk 1 [ 19.825665] raid5: allocated 7334kB for md0 [ 19.825667] raid5: raid level 5 set md0 active with 7 out of 7 devices, algorithm 2 [ 19.825669] RAID5 conf printout: [ 19.825670] --- rd:7 wd:7 [ 19.825671] disk 0, o:1, dev:sdb1 [ 19.825672] disk 1, o:1, dev:sdc1 [ 19.825673] disk 2, o:1, dev:sdd1 [ 19.825675] disk 3, o:1, dev:sde1 [ 19.825676] disk 4, o:1, dev:sdf1 [ 19.825677] disk 5, o:1, dev:sdh [ 19.825679] disk 6, o:1, dev:sdg [ 19.899787] PM: Starting manual resume from disk [ 28.663228] Filesystem "md0": Disabling barriers, not supported by the underlying device [ 28.663228] XFS mounting filesystem md0 [ 28.884433] md: resync of RAID array md0 [ 28.884433] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. [ 28.884433] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync. [ 28.884433] md: using 128k window, over a total of 976759936 blocks. [ 29.025980] Starting XFS recovery on filesystem: md0 (logdev: internal) [ 32.680486] XFS: xlog_recover_process_data: bad clientid [ 32.680495] XFS: log mount/recovery failed: error 5 [ 32.682773] XFS: log mount failed I ran fdisk and flagged sdg1 and sdh1 as fd. I tried to reassemble the array but it didnt work: no matter what was in mdadm.conf, it still uses sdg and sdh instead of sdg1 and sdh1. I checked in /dev and I see no sdg1 and and sdh1, shich explains why it wont use it. I just don't know why those partitions are gone from /dev and how to readd those... blkid : /dev/sda1: LABEL="boot" UUID="519790ae-32fe-4c15-a7f6-f1bea8139409" TYPE="ext2" /dev/sda2: TYPE="swap" /dev/sda3: LABEL="root" UUID="91390d23-ed31-4af0-917e-e599457f6155" TYPE="ext3" /dev/sdb1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdc1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdd1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sde1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdf1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdg: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdh: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" fdisk -l : Disk /dev/sda: 40.0 GB, 40020664320 bytes 255 heads, 63 sectors/track, 4865 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x8c878c87 Device Boot Start End Blocks Id System /dev/sda1 * 1 12 96358+ 83 Linux /dev/sda2 13 134 979965 82 Linux swap / Solaris /dev/sda3 135 4865 38001757+ 83 Linux Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x1e7481a5 Device Boot Start End Blocks Id System /dev/sdb1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xc9bdc1e9 Device Boot Start End Blocks Id System /dev/sdc1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdd: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xcc356c30 Device Boot Start End Blocks Id System /dev/sdd1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sde: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xe87f7a3d Device Boot Start End Blocks Id System /dev/sde1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdf: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xb17a2d22 Device Boot Start End Blocks Id System /dev/sdf1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdg: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x8f3bce61 Device Boot Start End Blocks Id System /dev/sdg1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdh: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xa98062ce Device Boot Start End Blocks Id System /dev/sdh1 1 121601 976760001 fd Linux raid autodetect I really dont know what happened nor how to recover from this mess. Needless to say the 5TB or so worth of data sitting on those disks are very valuable to me... Any idea any one? Did anybody ever experienced a similar situation or know how to recover from it ? Can someone help me? I'm really desperate... :x

  Read the article

• How to install MariaDB rpms in CentOS 6.4 using rpm (not yum cmd) + handling mysql-libs conflicts

  - by Pat C

  I need to script the install of MariaDB using the rpm command in CentOS 6.4. I can't use yum since it's going to be an offline install so there's no access to the repository. The only MySQL package installed is mysql-libs as various other packages in CentOS depend on it. When I did a test install of MariaDB with yum it correctly accounted for mysql-libs and uninstalled it at the end as MariaDB could handle the dependencies after it was installed: [root@new-host-6 ~]# yum install MariaDB-client MariaDB-common MariaDB-compat MariaDB-devel MariaDB-server MariaDB-shared Loaded plugins: downloadonly, fastestmirror, refresh-packagekit, security, verify Loading mirror speeds from cached hostfile * base: mirrors.kernel.org * extras: mirror.keystealth.org * updates: mirror.umd.edu Setting up Install Process Resolving Dependencies --> Running transaction check ---> Package MariaDB-client.x86_64 0:5.5.32-1 will be installed ---> Package MariaDB-common.x86_64 0:5.5.32-1 will be installed ---> Package MariaDB-compat.x86_64 0:5.5.32-1 will be obsoleting ---> Package MariaDB-devel.x86_64 0:5.5.32-1 will be installed ---> Package MariaDB-server.x86_64 0:5.5.32-1 will be installed ---> Package MariaDB-shared.x86_64 0:5.5.32-1 will be obsoleting ---> Package mysql-libs.x86_64 0:5.1.66-2.el6_3 will be obsoleted --> Finished Dependency Resolution Dependencies Resolved ==================================================================================================================================================================== Package Arch Version Repository Size ==================================================================================================================================================================== Installing: MariaDB-client x86_64 5.5.32-1 mariadb 10 M MariaDB-common x86_64 5.5.32-1 mariadb 23 k MariaDB-compat x86_64 5.5.32-1 mariadb 2.7 M replacing mysql-libs.x86_64 5.1.66-2.el6_3 MariaDB-devel x86_64 5.5.32-1 mariadb 5.6 M MariaDB-server x86_64 5.5.32-1 mariadb 34 M MariaDB-shared x86_64 5.5.32-1 mariadb 1.1 M replacing mysql-libs.x86_64 5.1.66-2.el6_3 Transaction Summary ==================================================================================================================================================================== Install 6 Package(s) Total download size: 53 M Is this ok [y/N]: y Downloading Packages: (1/6): MariaDB-5.5.32-centos6-x86_64-client.rpm | 10 MB 00:06 (2/6): MariaDB-5.5.32-centos6-x86_64-common.rpm | 23 kB 00:00 (3/6): MariaDB-5.5.32-centos6-x86_64-compat.rpm | 2.7 MB 00:02 (4/6): MariaDB-5.5.32-centos6-x86_64-devel.rpm | 5.6 MB 00:06 (5/6): MariaDB-5.5.32-centos6-x86_64-server.rpm | 34 MB 00:23 (6/6): MariaDB-5.5.32-centos6-x86_64-shared.rpm | 1.1 MB 00:00 -------------------------------------------------------------------------------------------------------------------------------------------------------------------- Total 1.3 MB/s | 53 MB 00:40 warning: rpmts_HdrFromFdno: Header V4 DSA/SHA1 Signature, key ID 1bb943db: NOKEY Retrieving key from https://yum.mariadb.org/RPM-GPG-KEY-MariaDB Importing GPG key 0x1BB943DB: Userid: "Daniel Bartholomew (Monty Program signing key) <[email protected]>" From : https://yum.mariadb.org/RPM-GPG-KEY-MariaDB Is this ok [y/N]: y Running rpm_check_debug Running Transaction Test Transaction Test Succeeded Running Transaction Warning: RPMDB altered outside of yum. Installing : MariaDB-compat-5.5.32-1.x86_64 1/7 Installing : MariaDB-common-5.5.32-1.x86_64 2/7 Installing : MariaDB-server-5.5.32-1.x86_64 3/7 chown: cannot access `/var/lib/mysql': No such file or directory PLEASE REMEMBER TO SET A PASSWORD FOR THE MariaDB root USER ! To do so, start the server, then issue the following commands: '/usr/bin/mysqladmin' -u root password 'new-password' '/usr/bin/mysqladmin' -u root -h new-host-6 password 'new-password' Alternatively you can run: '/usr/bin/mysql_secure_installation' which will also give you the option of removing the test databases and anonymous user created by default. This is strongly recommended for production servers. See the MariaDB Knowledgebase at http://kb.askmonty.org or the MySQL manual for more instructions. Please report any problems with the '/usr/bin/mysqlbug' script! The latest information about MariaDB is available at http://mariadb.org/. You can find additional information about the MySQL part at: http://dev.mysql.com Support MariaDB development by buying support/new features from Monty Program Ab. You can contact us about this at [email protected]. Alternatively consider joining our community based development effort: http://kb.askmonty.org/en/contributing-to-the-mariadb-project/ Installing : MariaDB-devel-5.5.32-1.x86_64 4/7 Installing : MariaDB-client-5.5.32-1.x86_64 5/7 Installing : MariaDB-shared-5.5.32-1.x86_64 6/7 Erasing : mysql-libs-5.1.66-2.el6_3.x86_64 7/7 Verifying : MariaDB-common-5.5.32-1.x86_64 1/7 Verifying : MariaDB-server-5.5.32-1.x86_64 2/7 Verifying : MariaDB-devel-5.5.32-1.x86_64 3/7 Verifying : MariaDB-client-5.5.32-1.x86_64 4/7 Verifying : MariaDB-compat-5.5.32-1.x86_64 5/7 Verifying : MariaDB-shared-5.5.32-1.x86_64 6/7 Verifying : mysql-libs-5.1.66-2.el6_3.x86_64 7/7 Installed: MariaDB-client.x86_64 0:5.5.32-1 MariaDB-common.x86_64 0:5.5.32-1 MariaDB-compat.x86_64 0:5.5.32-1 MariaDB-devel.x86_64 0:5.5.32-1 MariaDB-server.x86_64 0:5.5.32-1 MariaDB-shared.x86_64 0:5.5.32-1 Replaced: mysql-libs.x86_64 0:5.1.66-2.el6_3 Complete! My question is, what is the equivalent way to install the MariaDB packages using the rpm command only as opposed to yum? If I do rpm -ivh MariaDB*.rpm, I will get a ton of messages like the following about conflicts with mysql-libs: file /etc/my.cnf from install of MariaDB-common-5.5.32-1.x86_64 conflicts with file from package mysql-libs-5.1.66-2.el6_3.x86_64 file /usr/share/mysql/charsets/Index.xml from install of MariaDB-common-5.5.32-1.x86_64 conflicts with file from package mysql-libs-5.1.66-2.el6_3.x86_64 I then used the --force option to install the MariaDB rpms and uninstalled mysql-lib, I didn't get any weird messages but I'm not sure that is the cleanest method to handle the conflicts and do the install. So can someone confirm that installing MariaDB with the following rpm commands would be the same as using yum to install the packages and handle mysql-libs conflicts/removal: rpm -ivh --force MariaDB*.rpm rpm -e mysql-libs Thanks for any input!

  Read the article

• local user cannot access vsftpd server

  - by Zloy Smiertniy

  I'm currently running a vsftpd server and I added the necessary configurations in vsftpd.conf so that local users can use clients like FileZilla to manage their homes in a server. I found out that only users in the sudoers list access without a problem only they can't download the files, but users that are not sudoers cannot even access their homes from a client but they can access by a web browser using the FTP protocol and they can only access their home directories (as intented) Im running a fedora 14 on my server and my vsftpd.conf looks like this: # Example config file /etc/vsftpd/vsftpd.conf # # The default compiled in settings are fairly paranoid. This sample file # loosens things up a bit, to make the ftp daemon more usable. # Please see vsftpd.conf.5 for all compiled in defaults. # # READ THIS: This example file is NOT an exhaustive list of vsftpd options. # Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's # capabilities. # # Allow anonymous FTP? (Beware - allowed by default if you comment this out). anonymous_enable=NO # # Uncomment this to allow local users to log in. local_enable=YES # # Uncomment this to enable any form of FTP write command. write_enable=YES # # Default umask for local users is 077. You may wish to change this to 022, # if your users expect that (022 is used by most other ftpd's) local_umask=022 # # Uncomment this to allow the anonymous FTP user to upload files. This only # has an effect if the above global write enable is activated. Also, you will # obviously need to create a directory writable by the FTP user. #anon_upload_enable=YES # # Uncomment this if you want the anonymous FTP user to be able to create # new directories. #anon_mkdir_write_enable=YES # # Activate directory messages - messages given to remote users when they # go into a certain directory. dirmessage_enable=YES # # The target log file can be vsftpd_log_file or xferlog_file. # This depends on setting xferlog_std_format parameter xferlog_enable=YES # # Make sure PORT transfer connections originate from port 20 (ftp-data). connect_from_port_20=YES # # If you want, you can arrange for uploaded anonymous files to be owned by # a different user. Note! Using "root" for uploaded files is not # recommended! #chown_uploads=YES #chown_username=whoever # # The name of log file when xferlog_enable=YES and xferlog_std_format=YES # WARNING - changing this filename affects /etc/logrotate.d/vsftpd.log #xferlog_file=/var/log/xferlog # # Switches between logging into vsftpd_log_file and xferlog_file files. # NO writes to vsftpd_log_file, YES to xferlog_file xferlog_std_format=YES # # You may change the default value for timing out an idle session. #idle_session_timeout=600 # # You may change the default value for timing out a data connection. #data_connection_timeout=120 # # It is recommended that you define on your system a unique user which the # ftp server can use as a totally isolated and unprivileged user. #nopriv_user=ftpsecure # # Enable this and the server will recognise asynchronous ABOR requests. Not # recommended for security (the code is non-trivial). Not enabling it, # however, may confuse older FTP clients. #async_abor_enable=YES # # By default the server will pretend to allow ASCII mode but in fact ignore # the request. Turn on the below options to have the server actually do ASCII # mangling on files when in ASCII mode. # Beware that on some FTP servers, ASCII support allows a denial of service # attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd # predicted this attack and has always been safe, reporting the size of the # raw file. # ASCII mangling is a horrible feature of the protocol. ascii_upload_enable=YES ascii_download_enable=YES # # You may fully customise the login banner string: ftpd_banner=Welcome to GAMBITA FTP service # # You may specify a file of disallowed anonymous e-mail addresses. Apparently # useful for combatting certain DoS attacks. #deny_email_enable=YES # (default follows) #banned_email_file=/etc/vsftpd/banned_emails # # You may specify an explicit list of local users to chroot() to their home # directory. If chroot_local_user is YES, then this list becomes a list of # users to NOT chroot(). chroot_local_user=YES chroot_list_enable=YES # (default follows) chroot_list_file=/etc/vsftpd/chroot_list # # You may activate the "-R" option to the builtin ls. This is disabled by # default to avoid remote users being able to cause excessive I/O on large # sites. However, some broken FTP clients such as "ncftp" and "mirror" assume # the presence of the "-R" option, so there is a strong case for enabling it. ls_recurse_enable=YES # # When "listen" directive is enabled, vsftpd runs in standalone mode and # listens on IPv4 sockets. This directive cannot be used in conjunction # with the listen_ipv6 directive. listen=YES # # This directive enables listening on IPv6 sockets. To listen on IPv4 and IPv6 # sockets, you must run two copies of vsftpd with two configuration files. # Make sure, that one of the listen options is commented !! #listen_ipv6=YES pam_service_name=vsftpd userlist_enable=YES tcp_wrappers=YES use_localtime=YES Anyone has an idea of what might be happening? Nothing concerning vsftpd is written in any log

  Read the article

• OpenVPN IPv6 over IPv4 tunnel

  - by user66779

  Today I installed OpenVPN 2.3rc2 on both my windows 7 client machine and centos 6 server. This new version of OpenVPN provides full compatibility for IPv6. The Problem: I am currently able to connect to the server (through the IPv4 tunnel) and ping the IPv6 address which is assigned to my client and I can also ping the tun0 interface on the server. However, I cannot browse to any IPv6 websites. My vps provider has given me this: 2607:f840:0044:0022:0000:0000:0000:0000/64 is routed to this server (2607:f840:0:3f:0:0:0:eda). This is ifconfig after setup with OpenVPN running: eth0 Link encap:Ethernet HWaddr 00:16:3E:12:77:54 inet addr:208.111.39.160 Bcast:208.111.39.255 Mask:255.255.255.0 inet6 addr: 2607:f740:0:3f::eda/64 Scope:Global inet6 addr: fe80::216:3eff:fe12:7754/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2317253 errors:0 dropped:7263 overruns:0 frame:0 TX packets:1977414 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1696120096 (1.5 GiB) TX bytes:1735352992 (1.6 GiB) Interrupt:29 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 inet6 addr: 2607:f740:44:22::1/64 Scope:Global UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:739567 errors:0 dropped:0 overruns:0 frame:0 TX packets:1218240 errors:0 dropped:1542 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:46512557 (44.3 MiB) TX bytes:1559930874 (1.4 GiB) So OpenVPN is sucessfully creating a tun0 interface and assigning clients IPv6 addresses using 2607:f840:44:22::/64. The first client to connect is getting 2607:f840:44:22::1000 and the second 2607:f840:44:22::1001, and so on... plus 1 each time. After connecting as the first client, I can ping from my windows client machine 2607:f740:44:22::1 and 2607:f740:44:22::1000. However, I have no access to IPv6 websites. I believe the problem is that the tun0 IPv6 addressees are not being forwarded to the eth0 interface. This is the firewall running on the server: #!/bin/sh # # iptables configuration script # # Flush all current rules from iptables # iptables -F iptables -t nat -F # # Allow SSH connections on tcp port 22 # iptables -A INPUT -i eth0 -p tcp --dport 22 -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 22 -j ACCEPT # # Set access for localhost # iptables -A INPUT -i lo -j ACCEPT # # Accept connections on 1195 for vpn access from client # iptables -A INPUT -i eth0 -p udp --dport 1195 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p udp --sport 1195 -m state --state ESTABLISHED -j ACCEPT # # Apply forwarding for OpenVPN Tunneling # iptables -A FORWARD -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -A FORWARD -s 10.8.0.0/24 -j ACCEPT iptables -t nat -A POSTROUTING -o eth0 -j SNAT --to 209.111.39.160 iptables -A FORWARD -j REJECT # # Enable forwarding # echo 1 > /proc/sys/net/ipv4/ip_forward # # Set default policies for INPUT, FORWARD and OUTPUT chains # iptables -P INPUT ACCEPT iptables -P FORWARD ACCEPT iptables -P OUTPUT ACCEPT # # IPv6 # IP6TABLES=/sbin/ip6tables $IP6TABLES -F INPUT $IP6TABLES -F FORWARD $IP6TABLES -F OUTPUT echo -n "1" >/proc/sys/net/ipv6/conf/all/forwarding echo -n "1" >/proc/sys/net/ipv6/conf/all/proxy_ndp echo -n "0" >/proc/sys/net/ipv6/conf/all/autoconf echo -n "0" >/proc/sys/net/ipv6/conf/all/accept_ra $IP6TABLES -A INPUT -i eth0 -m state --state ESTABLISHED,RELATED -j ACCEPT $IP6TABLES -A INPUT -i eth0 -p tcp --dport 22 -j ACCEPT $IP6TABLES -A INPUT -i eth0 -p icmpv6 -j ACCEPT $IP6TABLES -P INPUT ACCEPT $IP6TABLES -P FORWARD ACCEPT $IP6TABLES -P OUTPUT ACCEPT Server.conf: server-ipv6 2607:f840:44:22::/64 server 10.8.0.0 255.255.255.0 port 1195 proto udp dev tun ca ca.crt cert server.crt key server.key dh dh2048.pem ifconfig-pool-persist ipp.txt push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 208.67.222.222" push "dhcp-option DNS 208.67.220.220" keepalive 10 60 tls-auth ta.key 0 cipher AES-256-CBC comp-lzo user nobody group nobody persist-key persist-tun status openvpn-status.log log-append openvpn.log verb 5 Client.conf: client dev tun nobind keepalive 10 60 hand-window 15 remote 209.111.39.160 1195 udp persist-key persist-tun ca ca.crt key client1.key cert client1.crt remote-cert-tls server tls-auth ta.key 1 comp-lzo verb 3 cipher AES-256-CBC I'm not sure where I am going wrong, it could be the firewall, or something missing from server or client.conf. This version of OpenVPN was only released yesterday, and there's little info on the internet about how to setup an IPv6 over IPv4 vpn tunnel. I've read the manual for this new version of OpenVPN (parts pertaining to IPv6) and it provides very little info too. Thanks for any help.

  Read the article

• Migrate from MySQL to PostgreSQL on Linux (Kubuntu)

  - by Dave Jarvis

  A long time ago in a galaxy far, far away... Trying to migrate a database from MySQL to PostgreSQL. All the documentation I have read covers, in great detail, how to migrate the structure. I have found very little documentation on migrating the data. The schema has 13 tables (which have been migrated successfully) and 9 GB of data. MySQL version: 5.1.x PostgreSQL version: 8.4.x I want to use the R programming language to analyze the data using SQL select statements; PostgreSQL has PL/R, but MySQL has nothing (as far as I can tell). A New Hope Create the database location (/var has insufficient space; also dislike having the PostgreSQL version number everywhere -- upgrading would break scripts!): sudo mkdir -p /home/postgres/main sudo cp -Rp /var/lib/postgresql/8.4/main /home/postgres sudo chown -R postgres.postgres /home/postgres sudo chmod -R 700 /home/postgres sudo usermod -d /home/postgres/ postgres All good to here. Next, restart the server and configure the database using these installation instructions: sudo apt-get install postgresql pgadmin3 sudo /etc/init.d/postgresql-8.4 stop sudo vi /etc/postgresql/8.4/main/postgresql.conf Change data_directory to /home/postgres/main sudo /etc/init.d/postgresql-8.4 start sudo -u postgres psql postgres \password postgres sudo -u postgres createdb climate pgadmin3 Use pgadmin3 to configure the database and create a schema. The episode continues in a remote shell known as bash, with both databases running, and the installation of a set of tools with a rather unusual logo: SQL Fairy. perl Makefile.PL sudo make install sudo apt-get install perl-doc (strangely, it is not called perldoc) perldoc SQL::Translator::Manual Extract a PostgreSQL-friendly DDL and all the MySQL data: sqlt -f DBI --dsn dbi:mysql:climate --db-user user --db-password password -t PostgreSQL > climate-pg-ddl.sql mysqldump --skip-add-locks --complete-insert --no-create-db --no-create-info --quick --result-file="climate-my.sql" --databases climate --skip-comments -u root -p The Database Strikes Back Recreate the structure in PostgreSQL as follows: pgadmin3 (switch to it) Click the Execute arbitrary SQL queries icon Open climate-pg-ddl.sql Search for TABLE " replace with TABLE climate." (insert the schema name climate) Search for on " replace with on climate." (insert the schema name climate) Press F5 to execute This results in: Query returned successfully with no result in 122 ms. Replies of the Jedi At this point I am stumped. Where do I go from here (what are the steps) to convert climate-my.sql to climate-pg.sql so that they can be executed against PostgreSQL? How to I make sure the indexes are copied over correctly (to maintain referential integrity; I don't have constraints at the moment to ease the transition)? How do I ensure that adding new rows in PostgreSQL will start enumerating from the index of the last row inserted (and not conflict with an existing primary key from the sequence)? How do you ensure the schema name comes through when transforming the data from MySQL to PostgreSQL inserts? Resources A fair bit of information was needed to get this far: https://help.ubuntu.com/community/PostgreSQL http://articles.sitepoint.com/article/site-mysql-postgresql-1 http://wiki.postgresql.org/wiki/Converting_from_other_Databases_to_PostgreSQL#MySQL http://pgfoundry.org/frs/shownotes.php?release_id=810 http://sqlfairy.sourceforge.net/ Thank you!

  Read the article

• jsf application in jboss web server

  - by chetan

  I try to run jsf application in myeclipse using jboss web server and following error while running jboss server. ERROR [AbstractKernelController] Error installing to Parse: name=vfsfile:/E:/ctn%20sodtware/jboss-5.0.1.GA/server/default/deploy/3aprwebdemo.war/ state=Not Installed mode=Manual requiredState=Parse org.jboss.deployers.spi.DeploymentException: Error creating managed object for vfsfile:/E:/ctn%20sodtware/jboss-5.0.1.GA/server/default/deploy/3aprwebdemo.war/ at org.jboss.deployers.spi.DeploymentException.rethrowAsDeploymentException(DeploymentException.java:49) at org.jboss.deployers.spi.deployer.helpers.AbstractParsingDeployerWithOutput.createMetaData(AbstractParsingDeployerWithOutput.java:337) at org.jboss.deployers.spi.deployer.helpers.AbstractParsingDeployerWithOutput.createMetaData(AbstractParsingDeployerWithOutput.java:297) at org.jboss.deployers.spi.deployer.helpers.AbstractParsingDeployerWithOutput.createMetaData(AbstractParsingDeployerWithOutput.java:269) at org.jboss.deployers.spi.deployer.helpers.AbstractParsingDeployerWithOutput.deploy(AbstractParsingDeployerWithOutput.java:230) at org.jboss.deployers.plugins.deployers.DeployerWrapper.deploy(DeployerWrapper.java:171) at org.jboss.deployers.plugins.deployers.DeployersImpl.doDeploy(DeployersImpl.java:1439) at org.jboss.deployers.plugins.deployers.DeployersImpl.doInstallParentFirst(DeployersImpl.java:1157) at org.jboss.deployers.plugins.deployers.DeployersImpl.install(DeployersImpl.java:1098) at org.jboss.dependency.plugins.AbstractControllerContext.install(AbstractControllerContext.java:348) at org.jboss.dependency.plugins.AbstractController.install(AbstractController.java:1598) at org.jboss.dependency.plugins.AbstractController.incrementState(AbstractController.java:934) at org.jboss.dependency.plugins.AbstractController.resolveContexts(AbstractController.java:1062) at org.jboss.dependency.plugins.AbstractController.resolveContexts(AbstractController.java:984) at org.jboss.dependency.plugins.AbstractController.change(AbstractController.java:822) at org.jboss.dependency.plugins.AbstractController.change(AbstractController.java:553) at org.jboss.deployers.plugins.deployers.DeployersImpl.process(DeployersImpl.java:781) at org.jboss.deployers.plugins.main.MainDeployerImpl.process(MainDeployerImpl.java:698) at org.jboss.system.server.profileservice.ProfileServiceBootstrap.loadProfile(ProfileServiceBootstrap.java:304) at org.jboss.system.server.profileservice.ProfileServiceBootstrap.start(ProfileServiceBootstrap.java:205) at org.jboss.bootstrap.AbstractServerImpl.start(AbstractServerImpl.java:405) at org.jboss.Main.boot(Main.java:209) at org.jboss.Main$1.run(Main.java:547) at java.lang.Thread.run(Thread.java:619) Caused by: org.jboss.xb.binding.JBossXBException: Failed to parse source: cvc-datatype-valid.1.2.1: '3aprwebdemo' is not a valid value for 'NCName'. @ vfsfile:/E:/ctn%20sodtware/jboss-5.0.1.GA/server/default/deploy/3aprwebdemo.war/WEB-INF/web.xml[5,20] at org.jboss.xb.binding.parser.sax.SaxJBossXBParser.parse(SaxJBossXBParser.java:203) at org.jboss.xb.binding.UnmarshallerImpl.unmarshal(UnmarshallerImpl.java:168) at org.jboss.deployers.vfs.spi.deployer.JBossXBDeployerHelper.parse(JBossXBDeployerHelper.java:199) at org.jboss.deployers.vfs.spi.deployer.JBossXBDeployerHelper.parse(JBossXBDeployerHelper.java:170) at org.jboss.deployers.vfs.spi.deployer.SchemaResolverDeployer.parse(SchemaResolverDeployer.java:132) at org.jboss.deployers.vfs.spi.deployer.SchemaResolverDeployer.parse(SchemaResolverDeployer.java:118) at org.jboss.deployers.vfs.spi.deployer.AbstractVFSParsingDeployer.parseAndInit(AbstractVFSParsingDeployer.java:256) at org.jboss.deployers.vfs.spi.deployer.AbstractVFSParsingDeployer.parse(AbstractVFSParsingDeployer.java:188) at org.jboss.deployers.spi.deployer.helpers.AbstractParsingDeployerWithOutput.createMetaData(AbstractParsingDeployerWithOutput.java:323) ... 22 more Caused by: org.xml.sax.SAXException: cvc-datatype-valid.1.2.1: '3aprwebdemo' is not a valid value for 'NCName'. @ vfsfile:/E:/ctn%20sodtware/jboss-5.0.1.GA/server/default/deploy/3aprwebdemo.war/WEB-INF/web.xml[5,20] at org.jboss.xb.binding.parser.sax.SaxJBossXBParser$MetaDataErrorHandler.error(SaxJBossXBParser.java:426) at org.apache.xerces.util.ErrorHandlerWrapper.error(Unknown Source) at org.apache.xerces.impl.XMLErrorReporter.reportError(Unknown Source) at org.apache.xerces.impl.XMLErrorReporter.reportError(Unknown Source) at org.apache.xerces.impl.XMLErrorReporter.reportError(Unknown Source) at org.apache.xerces.impl.xs.XMLSchemaValidator$XSIErrorReporter.reportError(Unknown Source) at org.apache.xerces.impl.xs.XMLSchemaValidator.reportSchemaError(Unknown Source) at org.apache.xerces.impl.xs.XMLSchemaValidator.processOneAttribute(Unknown Source) at org.apache.xerces.impl.xs.XMLSchemaValidator.processAttributes(Unknown Source) at org.apache.xerces.impl.xs.XMLSchemaValidator.handleStartElement(Unknown Source) at org.apache.xerces.impl.xs.XMLSchemaValidator.startElement(Unknown Source) at org.apache.xerces.xinclude.XIncludeHandler.startElement(Unknown Source) at org.apache.xerces.impl.XMLNSDocumentScannerImpl.scanStartElement(Unknown Source) at org.apache.xerces.impl.XMLNSDocumentScannerImpl$NSContentDispatcher.scanRootElementHook(Unknown Source) at org.apache.xerces.impl.XMLDocumentFragmentScannerImpl$FragmentContentDispatcher.dispatch(Unknown Source) at org.apache.xerces.impl.XMLDocumentFragmentScannerImpl.scanDocument(Unknown Source) at org.apache.xerces.parsers.XML11Configuration.parse(Unknown Source) at org.apache.xerces.parsers.XML11Configuration.parse(Unknown Source) at org.apache.xerces.parsers.XMLParser.parse(Unknown Source) at org.apache.xerces.parsers.AbstractSAXParser.parse(Unknown Source) at org.apache.xerces.jaxp.SAXParserImpl$JAXPSAXParser.parse(Unknown Source) at org.jboss.xb.binding.parser.sax.SaxJBossXBParser.parse(SaxJBossXBParser.java:199) ... 30 more

  Read the article

• What git branching models actually work - the final question

  - by UncleCJ

  In our company we have successfully deployed git and we are currently using a simple trunk/release/hotfixes branching model. However, this has it's problems, I have some key issues of confusion in the community which would be awesome to have answered here. Maybe my hopes for an Alexander stroke are too great, quite possibly I'll decompose this question into more manageable issues, but here's my first shot. Workflows / branching models - below are the three main descriptions of this I have seen, but they are partially contradicting each other or don't go far enough to sort out the subsequent issues we've run into (as described below). Thus our team so far defaults to not so great solutions. Are you doing something better? gitworkflows(7) Manual Page (nvie) A successful Git branching model (reinh) A Git Workflow for Agile Teams Merging vs rebasing (tangled vs sequential history) - the bids on this are as confusing as it gets. Should one pull --rebase or wait with merging back to the mainline until your task is finished? Personally I lean towards merging since this preserves a visual illustration of on which base a task was started and finished, and I even prefer merge --no-ff for this purpose. It has other drawbacks however. Also many haven't realized the useful property of merging - that it isn't commutative (merging a topic branch into master does not mean merging master into the topic branch). I am looking for a natural workflow - sometimes mistakes happen because our procedures don't capture a specific situation with simple rules. For example a fix needed for earlier releases should of course be based sufficiently downstream to be possible to merge upstream into all branches necessary (is the usage of these terms clear enough?). However it happens that a fix makes it into the master before the developer realizes it should have been placed further downstream, and if that is already pushed (even worse, merged or something based on it) then the option remaining is cherry-picking, with it's associated perils... What simple rules like such do you use? Also in this is included the awkwardness of one topic branch necessarily excluding other topic branches (assuming they are branched from a common baseline). Developers don't want to finish a feature to start another one feeling like the code they just wrote is not there anymore How to avoid creating merge conflicts (due to cherry-pick)? What seems like a sure way to create a merge conflict is to cherry-pick between branches, they can never be merged again? Would applying the same commit in revert (how to do this?) in either branch possibly solve this situation? This is one reason I do not dare to push for a largely merge-based workflow. How to decompose into topical branches? - We realize that it would be awesome to assemble a finished integration from topic branches, but often work by our developers is not clearly defined (sometimes as simple as "poking around") and if some code has already gone into a "misc" topic, it can not be taken out of there again, according to the question above? How do you work with defining/approving/graduating/releasing your topic branches? Proper procedures like code review and graduating would of course be lovely, but we simply cannot keep things untangled enough to manage this - any suggestions? integration branches, illustration please? Vote and comment as much as you'd like, I'll try to keep the issue page clear and informative enough. Thanks! Below is a list of related topics on stackoverflow I have checked out: What are some good strategies to allow deployed applications to be hotfixable? Workflow description for git usage for in-house development Git workflow for corporate Linux kernel development How do you maintain development code and production code? (thanks for this PDF!) git releases management Git Cherry-pick vs Merge Workflow How to cherry-pick multiple commits How do you merge selective files with git-merge? How to cherry pick a range of commits and merge into another branch ReinH Git Workflow git workflow for making modifications you’ll never push back to origin Cherry-pick a merge Proper Git workflow for combined OS and Private code? Maintaining Project with Git Why cant Git merge file changes with a modified parent/master. Git branching / rebasing good practices When will "git pull --rebase" get me in to trouble?

  Read the article

• just can't get a controller to work

  - by Asaf

  I try to get into mysite/user so that application/classes/controller/user.php should be working, now this is my file tree: code of controller/user.php: <?php defined('SYSPATH') OR die('No direct access allowed.'); class Controller_User extends Controller_Default { public $template = 'user'; function action_index() { //$view = View::factory('user'); //$view->render(TRUE); $this->template->message = 'hello, world!'; } } ?> code of controller/default.php: <?php defined('SYSPATH') OR die('No direct access allowed.'); class Controller_default extends Controller_Template { } bootstrap.php: <?php defined('SYSPATH') or die('No direct script access.'); //-- Environment setup -------------------------------------------------------- /** * Set the default time zone. * * @see http://kohanaframework.org/guide/using.configuration * @see http://php.net/timezones */ date_default_timezone_set('America/Chicago'); /** * Set the default locale. * * @see http://kohanaframework.org/guide/using.configuration * @see http://php.net/setlocale */ setlocale(LC_ALL, 'en_US.utf-8'); /** * Enable the Kohana auto-loader. * * @see http://kohanaframework.org/guide/using.autoloading * @see http://php.net/spl_autoload_register */ spl_autoload_register(array('Kohana', 'auto_load')); /** * Enable the Kohana auto-loader for unserialization. * * @see http://php.net/spl_autoload_call * @see http://php.net/manual/var.configuration.php#unserialize-callback-func */ ini_set('unserialize_callback_func', 'spl_autoload_call'); //-- Configuration and initialization ----------------------------------------- /** * Initialize Kohana, setting the default options. * * The following options are available: * * - string base_url path, and optionally domain, of your application NULL * - string index_file name of your index file, usually "index.php" index.php * - string charset internal character set used for input and output utf-8 * - string cache_dir set the internal cache directory APPPATH/cache * - boolean errors enable or disable error handling TRUE * - boolean profile enable or disable internal profiling TRUE * - boolean caching enable or disable internal caching FALSE */ Kohana::init(array( 'base_url' => '/mysite/', 'index_file' => FALSE, )); /** * Attach the file write to logging. Multiple writers are supported. */ Kohana::$log->attach(new Kohana_Log_File(APPPATH.'logs')); /** * Attach a file reader to config. Multiple readers are supported. */ Kohana::$config->attach(new Kohana_Config_File); /** * Enable modules. Modules are referenced by a relative or absolute path. */ Kohana::modules(array( 'auth' => MODPATH.'auth', // Basic authentication 'cache' => MODPATH.'cache', // Caching with multiple backends 'codebench' => MODPATH.'codebench', // Benchmarking tool 'database' => MODPATH.'database', // Database access 'image' => MODPATH.'image', // Image manipulation 'orm' => MODPATH.'orm', // Object Relationship Mapping 'pagination' => MODPATH.'pagination', // Paging of results 'userguide' => MODPATH.'userguide', // User guide and API documentation )); /** * Set the routes. Each route must have a minimum of a name, a URI and a set of * defaults for the URI. */ Route::set('default', '(<controller>(/<action>(/<id>)))') ->defaults(array( 'controller' => 'welcome', 'action' => 'index', )); /** * Execute the main request. A source of the URI can be passed, eg: $_SERVER['PATH_INFO']. * If no source is specified, the URI will be automatically detected. */ echo Request::instance() ->execute() ->send_headers() ->response; ?> .htaccess: RewriteEngine On RewriteBase /mysite/ RewriteRule ^(application|modules|system) - [F,L] RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule .* index.php/$0 [PT,L] Trying to go to http://localhost/ makes the "hello world" page, from the welcome.php Trying to go to http://localhost/mysite/user give me this: The requested URL /mysite/user was not found on this server.

  Read the article

• Possible bug in ASP.NET MVC with form values being replaced.

  - by Dan Atkinson

  I appear to be having a problem with ASP.NET MVC in that, if I have more than one form on a page which uses the same name in each one, but as different types (radio/hidden/etc), then, when the first form posts (I choose the 'Date' radio button for instance), if the form is re-rendered (say as part of the results page), I seem to have the issue that the hidden value of the SearchType on the other forms is changed to the last radio button value (in this case, SearchType.Name). Below is an example form for reduction purposes. <% Html.BeginForm("Search", "Search", FormMethod.Post); %> <%= Html.RadioButton("SearchType", SearchType.Date, true) %> <%= Html.RadioButton("SearchType", SearchType.Name) %> <input type="submit" name="submitForm" value="Submit" /> <% Html.EndForm(); %> <% Html.BeginForm("Search", "Search", FormMethod.Post); %> <%= Html.Hidden("SearchType", SearchType.Colour) %> <input type="submit" name="submitForm" value="Submit" /> <% Html.EndForm(); %> <% Html.BeginForm("Search", "Search", FormMethod.Post); %> <%= Html.Hidden("SearchType", SearchType.Reference) %> <input type="submit" name="submitForm" value="Submit" /> <% Html.EndForm(); %> Resulting page source (this would be part of the results page) <form action="/Search/Search" method="post"> <input type="radio" name="SearchType" value="Date" /> <input type="radio" name="SearchType" value="Name" /> <input type="submit" name="submitForm" value="Submit" /> </form> <form action="/Search/Search" method="post"> <input type="hidden" name="SearchType" value="Name" /> <!-- Should be Colour --> <input type="submit" name="submitForm" value="Submit" /> </form> <form action="/Search/Search" method="post"> <input type="hidden" name="SearchType" value="Name" /> <!-- Should be Reference --> <input type="submit" name="submitForm" value="Submit" /> </form> Please can anyone else with RC1 confirm this? Maybe it's because I'm using an enum. I don't know. I should add that I can circumvent this issue by using 'manual' input () tags for the hidden fields, but if I use MVC tags (<%= Html.Hidden(...) %), .NET MVC replaces them every time. Many thanks. Update: I've seen this bug again today. It seems that this crops its head when you return a posted page and use MVC set hidden form tags with the Html helper. I've contacted Phil Haack about this, because I don't know where else to turn, and I don't believe that this should be expected behaviour as specified by David.

  Read the article

• zLib on iPhone, stop at first BLOCK

  - by cedric

  I am trying to call iPhone zLib to decompress the zlib stream from our HTTP based server, but the code always stop after finishing the first zlib block. Obviously, iPhone SDK is using the standard open Zlib. My doubt is that the parameter for inflateInit2 is not appropriate here. I spent lots of time reading the zlib manual, but it isn't that helpful. Here is the details, your help is appreciated. (1) the HTTP request: NSURL *url = [NSURL URLWithString:@"http://192.168.0.98:82/WIC?query=getcontacts&PIN=12345678&compression=Y"]; (2) The data I get from server is something like this (if decompressed). The stream was compressed by C# zlib class DeflateStream: $REC_TYPE=SYS Status=OK Message=OK SetID= IsLast=Y StartIndex=0 LastIndex=6 EOR ...... $REC_TYPE=CONTACTSDISTLIST ID=2 Name=CTU+L%2EA%2E OnCallEnabled=Y OnCallMinUsers=1 OnCallEditRight= OnCallEditDLRight=D Fields= CL= OnCallStatus= EOR (3) However, I will only get the first Block. The code for decompression on iPhone (copied from a code piece from somewhere here) is as follow. The loop between Line 23~38 always break the second time execution. + (NSData *) uncompress: (NSData*) data { 1 if ([data length] == 0) return nil; 2 NSInteger length = [data length]; 3 unsigned full_length = length; 4 unsigned half_length =length/ 2; 5 NSMutableData *decompressed = [NSMutableData dataWithLength: 5*full_length + half_length]; 6 BOOL done = NO; 7 int status; 8 z_stream strm; 9 length=length-4; 10 void* bytes= malloc(length); 11 NSRange range; 12 range.location=4; 13 range.length=length; 14 [data getBytes: bytes range: range]; 15 strm.next_in = bytes; 16 strm.avail_in = length; 17 strm.total_out = 0; 18 strm.zalloc = Z_NULL; 19 strm.zfree = Z_NULL; 20 strm.data_type= Z_BINARY; 21 // if (inflateInit(&strm) != Z_OK) return nil; 22 if (inflateInit2(&strm, (-15)) != Z_OK) return nil; //It won't work if change -15 to positive numbers. 23 while (!done) 24 { 25 // Make sure we have enough room and reset the lengths. 26 if (strm.total_out >= [decompressed length]) 27 [decompressed increaseLengthBy: half_length]; 28 strm.next_out = [decompressed mutableBytes] + strm.total_out; 29 strm.avail_out = [decompressed length] - strm.total_out; 30 31 // Inflate another chunk. 32 status = inflate (&strm, Z_SYNC_FLUSH); //Z_SYNC_FLUSH-->Z_BLOCK, won't work either 33 if (status == Z_STREAM_END){ 34 35 done = YES; 36 } 37 else if (status != Z_OK) break; 38 } 39 if (inflateEnd (&strm) != Z_OK) return nil; 40 // Set real length. 41 if (done) 42 { 43 [decompressed setLength: strm.total_out]; 44 return [NSData dataWithData: decompressed]; 45 } 46 else return nil; 47 }

  Read the article

• Adding functionality to any TextReader

  - by strager

  I have a Location class which represents a location somewhere in a stream. (The class isn't coupled to any specific stream.) The location information will be used to match tokens to location in the input in my parser, to allow for nicer error reporting to the user. I want to add location tracking to a TextReader instance. This way, while reading tokens, I can grab the location (which is updated by the TextReader as data is read) and give it to the token during the tokenization process. I am looking for a good approach on accomplishing this goal. I have come up with several designs. Manual location tracking Every time I need to read from the TextReader, I call AdvanceString on the Location object of the tokenizer with the data read. Advantages Very simple. No class bloat. No need to rewrite the TextReader methods. Disadvantages Couples location tracking logic to tokenization process. Easy to forget to track something (though unit testing helps with this). Bloats existing code. Plain TextReader wrapper Create a LocatedTextReaderWrapper class which surrounds each method call, tracking a Location property. Example: public class LocatedTextReaderWrapper : TextReader { private TextReader source; public Location Location { get; set; } public LocatedTextReaderWrapper(TextReader source) : this(source, new Location()) { } public LocatedTextReaderWrapper(TextReader source, Location location) { this.Location = location; this.source = source; } public override int Read(char[] buffer, int index, int count) { int ret = this.source.Read(buffer, index, count); if(ret >= 0) { this.location.AdvanceString(string.Concat(buffer.Skip(index).Take(count))); } return ret; } // etc. } Advantages Tokenization doesn't know about Location tracking. Disadvantages User needs to create and dispose a LocatedTextReaderWrapper instance, in addition to their TextReader instance. Doesn't allow different types of tracking or different location trackers to be added without layers of wrappers. Event-based TextReader wrapper Like LocatedTextReaderWrapper, but decouples it from the Location object raising an event whenever data is read. Advantages Can be reused for other types of tracking. Tokenization doesn't know about Location tracking or other tracking. Can have multiple, independent Location objects (or other methods of tracking) tracking at once. Disadvantages Requires boilerplate code to enable location tracking. User needs to create and dispose the wrapper instance, in addition to their TextReader instance. Aspect-orientated approach Use AOP to perform like the event-based wrapper approach. Advantages Can be reused for other types of tracking. Tokenization doesn't know about Location tracking or other tracking. No need to rewrite the TextReader methods. Disadvantages Requires external dependencies, which I want to avoid. I am looking for the best approach in my situation. I would like to: Not bloat the tokenizer methods with location tracking. Not require heavy initialization in user code. Not have any/much boilerplate/duplicated code. (Perhaps) not couple the TextReader with the Location class. Any insight into this problem and possible solutions or adjustments are welcome. Thanks! (For those who want a specific question: What is the best way to wrap the functionality of a TextReader?) I have implemented the "Plain TextReader wrapper" and "Event-based TextReader wrapper" approaches and am displeased with both, for reasons mentioned in their disadvantages.

  Read the article

• Flex SDK missing fundamental things

  - by Bart van Heukelom

  All of a sudden Flash Builder 4 is missing all kinds of fundamental things and is generating incorrect errors. I've had the same issue yesterday, where I fixed it by downloading a new Flex SDK and importing that into FB. I did this again, but this time it fixed nothing. I don't think it's something I did, like removing critical references from the build path. The errors also appeared on projects I was not working on at the time. It occurs for ActionScript, Flex and Flex Library projects alike. Update 3: Well, i've singled the problem down to a single piece of code, though a very simple one. I can make a new workspace in FB and things work ok, then screw the workspace up forever by adding this code to a project. All projects will have errors and closing or even removing the faulty project does not change this. Making another new workspace (without the faulty code) makes my projects compile again. Link: http://www.the3rdage.net/files/2745/Main.as (i've uploaded the file in case an odd character or encoding error causes the error) Update 2: I've tried manual compiling with mxmlc, the same errors occur. It appears to be an SDK problem, not Flash Builder. Update: I find this stack trace in the Flash Builder error log: !ENTRY com.adobe.flexbuilder.project 4 43 2010-05-11 11:55:47.495 !MESSAGE Uncaught exception in compiler !STACK 0 java.lang.NullPointerException at macromedia.asc.semantics.ConstantEvaluator.evaluate(ConstantEvaluator.java:2592) at macromedia.asc.parser.VariableBindingNode.evaluate(VariableBindingNode.java:64) at macromedia.asc.semantics.ConstantEvaluator.evaluate(ConstantEvaluator.java:2233) at macromedia.asc.parser.ListNode.evaluate(ListNode.java:44) at macromedia.asc.semantics.ConstantEvaluator.evaluate(ConstantEvaluator.java:2578) at macromedia.asc.parser.VariableDefinitionNode.evaluate(VariableDefinitionNode.java:48) at macromedia.asc.semantics.ConstantEvaluator.evaluate(ConstantEvaluator.java:2310) at macromedia.asc.parser.StatementListNode.evaluate(StatementListNode.java:60) at macromedia.asc.semantics.ConstantEvaluator.evaluate(ConstantEvaluator.java:2503) at macromedia.asc.parser.WithStatementNode.evaluate(WithStatementNode.java:44) at macromedia.asc.semantics.ConstantEvaluator.evaluate(ConstantEvaluator.java:2310) at macromedia.asc.parser.StatementListNode.evaluate(StatementListNode.java:60) at macromedia.asc.semantics.ConstantEvaluator.evaluate(ConstantEvaluator.java:2891) at macromedia.asc.parser.FunctionCommonNode.evaluate(FunctionCommonNode.java:106) at macromedia.asc.semantics.ConstantEvaluator.evaluate(ConstantEvaluator.java:2905) at macromedia.asc.parser.FunctionCommonNode.evaluate(FunctionCommonNode.java:106) at macromedia.asc.semantics.ConstantEvaluator.evaluate(ConstantEvaluator.java:3643) at macromedia.asc.parser.ClassDefinitionNode.evaluate(ClassDefinitionNode.java:106) at macromedia.asc.semantics.ConstantEvaluator.evaluate(ConstantEvaluator.java:3371) at macromedia.asc.parser.ProgramNode.evaluate(ProgramNode.java:80) at flex2.compiler.as3.As3Compiler.analyze4(As3Compiler.java:709) at flex2.compiler.CompilerAPI.analyze(CompilerAPI.java:3089) at flex2.compiler.CompilerAPI.analyze(CompilerAPI.java:2977) at flex2.compiler.CompilerAPI.batch2(CompilerAPI.java:528) at flex2.compiler.CompilerAPI.batch(CompilerAPI.java:1274) at flex2.compiler.CompilerAPI.compile(CompilerAPI.java:1496) at flex2.tools.oem.Application.compile(Application.java:1188) at flex2.tools.oem.Application.recompile(Application.java:1133) at flex2.tools.oem.Application.compile(Application.java:819) at flex2.tools.flexbuilder.BuilderApplication.compile(BuilderApplication.java:344) at com.adobe.flexbuilder.multisdk.compiler.internal.ASApplicationBuilder$MyBuilder.mybuild(ASApplicationBuilder.java:276) at com.adobe.flexbuilder.multisdk.compiler.internal.ASApplicationBuilder.build(ASApplicationBuilder.java:127) at com.adobe.flexbuilder.multisdk.compiler.internal.ASBuilder.build(ASBuilder.java:190) at com.adobe.flexbuilder.multisdk.compiler.internal.ASItemBuilder.build(ASItemBuilder.java:74) at com.adobe.flexbuilder.project.compiler.internal.FlexProjectBuilder.buildItem(FlexProjectBuilder.java:480) at com.adobe.flexbuilder.project.compiler.internal.FlexProjectBuilder.build(FlexProjectBuilder.java:306) at com.adobe.flexbuilder.project.compiler.internal.FlexIncrementalBuilder.build(FlexIncrementalBuilder.java:157) at org.eclipse.core.internal.events.BuildManager$2.run(BuildManager.java:627) at org.eclipse.core.runtime.SafeRunner.run(SafeRunner.java:42) at org.eclipse.core.internal.events.BuildManager.basicBuild(BuildManager.java:170) at org.eclipse.core.internal.events.BuildManager.basicBuild(BuildManager.java:201) at org.eclipse.core.internal.events.BuildManager$1.run(BuildManager.java:253) at org.eclipse.core.runtime.SafeRunner.run(SafeRunner.java:42) at org.eclipse.core.internal.events.BuildManager.basicBuild(BuildManager.java:256) at org.eclipse.core.internal.events.BuildManager.basicBuildLoop(BuildManager.java:309) at org.eclipse.core.internal.events.BuildManager.build(BuildManager.java:341) at org.eclipse.core.internal.events.AutoBuildJob.doBuild(AutoBuildJob.java:140) at org.eclipse.core.internal.events.AutoBuildJob.run(AutoBuildJob.java:238) at org.eclipse.core.internal.jobs.Worker.run(Worker.java:55)

  Read the article

< Previous Page | 110 111 112 113 114 115 116 117 118 119 120 121  | Next Page >