Search Results

Search found 5926 results on 238 pages for 'driver verifier'.

Page 115/238 | < Previous Page | 111 112 113 114 115 116 117 118 119 120 121 122  | Next Page >

• Windows 7 Install: No drives were found

  - by Albert Bori

  I was building a computer for my wife with an older SATA hard drive that I had lying around, and when attempting to do a new install of Windows 7 on it, the installer says: "No drives were found. Click Load Driver to provide a mass storage driver for installation." I ran the diskpart command: list volume, and it showed up as "Raw". So, I formatted it to NTFS and then it showed up as a healthy drive in diskpart. I also ran check disk on it with no errors. Windows 7 installer STILL can't find the drive. As far as BIOS settings, I have tried "Native IDE", AHCI, and Both AHCI/IDE mode (SATA slots 0-2 AHCI, 3-4 IDE). I tried all combinations... still "no drives were found". At this point, I'm just scratching my head. Using the installation dos window, I can see and talk to the drive just fine, but the installer just doesn't see it at all. I've even written folders and files to the drive, and it still "can't be seen". Any help would be great. Items of interest: Motherboard model: Gigabyte GA-A75M-UD2H - BIOS Version F5 (latest) Hard drive model: 80GB Seagate Barracuda 7200.7 ST380817AS (no other drives) Installing Windows 7 using a FAT32 formatted USB Drive, which I've used for other installs

  Read the article

• Logitech Performance MX Mouse Jumps on OS X Lion (10.7.4)

  - by Adam Thompson

  I have a Logitech MX Revolution wireless mouse that I am trying to use with OS X Lion. Everything is working except for one problem... there is a small, but quite noticeable, jump when the mouse cursor is moved. The problem is mostly prevalent when dragging and dropping files or trying to highlight items. It makes performing any task with the mouse accurately next to impossible. I did quite a bit of looking and found that all kinds of people have had mouse issues with OS X. I've tried all of the following with absolutely no success: Using the official drivers from Logitech (these performed worse than the default mouse drivers in OS X) Using SteerMouse as a third party mouse driver. This worked ever so slightly better than the default driver, but still suffered quite frequently from the skipping problem Cleaning the sensor on the mouse and ensuring it's not the result of the surface that it's being used on. Tested the mouse on a Windows machine. The mouse worked absolutely flawlessly on the other machine. Changed the channel that my wireless router operates on by the off chance my problems were the result of interference. This also had no effect. I can't think of anything else that could possibly interfere with the mouse. I'm am out of ideas on what to try, so I would really appreciate if anyone has any suggestions. I should also mention that an old wired mouse I had laying around worked just fine when I plugged it in. This really isn't the best solution, however, as I really prefer the MX Revolution.

  Read the article

• Adjust output Brightness/Gamma/Colors in Gnome

  - by Mikee

  We have a desktop system running Ubuntu 8.04.4, and it is connected to a standard desktop LCD monitor. Unfortunately, in 8.04.4, the brightness of the image is cranked way up. It appears to be a graphics driver issue. Unfortunately, installing a newer GPU driver for this Intel GPU is very difficult to do. So, I am looking for a software (or config file?) solution to achieve this. Note: Ubuntu 9.10 and higher do not exhibit this issue, so this is not a hardware problem. Note: VNC-ing to this machine from another does not exhibit this issue either. Also, I installed "DisplayCalibrator.app", and it does not work very well (the app comes up, but the contents of the window are blank). Is there anything that I can add to the xorg.conf file to correct this issue? Also, this solution: http://superuser.com/questions/96539/adjust-contrast-and-brightness-in-ubuntu did not resove my issue. Thank you all for the help!

  Read the article

• Screen occasionally flashes black when under load, sometimes does not recover

  - by Oak

  I've built a brand new machine, but to my horror my monitor occasionally flashes black for around a second, then returning to normal. This happens under load (watching videos / playing games) but only sometimes; e.g. it doesn't occur in "Batman: Arkham City" but does in "XCOM: Enemy Unknown". When watching videos, it also occurs when not watching them full-screen, and it sometimes even occurs when the machine isn't doing anything, just sitting at the desktop and moving the mouse around. Has anyone ran into this problem and knows of any solution? Additionally, sometimes after the black screen, it won't return to normal, instead turning completely corrupt. In these cases even quitting the application doesn't help, but physically disconnecting and reconnecting the monitor fixes the problem. This problem did not occur on my earlier machine which used the same physical monitor. Additional details: Windows Server 2012, configured as Windows 8, with latest updates installed NVIDIA GeForce GTX 660 Ti, with latest driver installed Ample amounts of CPU and RAM for playing the above games and for watching videos. I've read about similar problems elsewhere but could not find a working solution: http://www.youtube.com/watch?v=Zt00C-HXFbA&noredirect=1 http://www.sevenforums.com/hardware-devices/59126-monitor-flashing-black.html https://eu.battle.net/d3/en/forum/topic/4079098908?page=4 http://www.tomshardware.com/forum/347422-33-screen-flickering-black-nvidia-driver-update

  Read the article

• Defining Virtual and Real User Directories with Dovecot & Postfix

  - by blankabout

  Following a wobble described in this question we now have virtual and real users authenticating with Dovecot, the problem now is that the real users (who have been on the system for years) can no longer access their mail. I'm guessing that it is because Dovecot is configured to point to the virtual mailboxes but not the real mail boxes. These are snippets from the config files: /etc/dovecot/dovecot.conf !include conf.d/*.conf /etc/dovecot/conf.d/10-auth.cong passdb { driver = passwd-file # Path for passwd-file. Also set the default password scheme. args = scheme=cram-md5 /etc/cram-md5.pwd } userdb { driver=static #args = mail_uid=dovecot mail_gid=dovecot /etc/dovecot/userdb args = uid=vmail gid=vmail home=/var/spool/vhosts/%d/%n /etc/dovecot/userdb } [email protected]:::::/var/spool/vhosts/virtualdomain.com/:/bin/false:: We think the problem is that the Dovecot file 10-auth.conf does not contain a method of accessing the mailboxes for the real users. We have looked around on this site, dovecot.org and done the usual googling but cannot find anywhere that describes how to set up virtual users on alongside legacy real users. Any help would be appreciated, especially by our real users who would like the contents of their inboxes to be available! If any further config is required, please let me know.

  Read the article

• Ubuntu network card problem.

  - by Steve Greene

  Hello folks, Several days ago, I installed Ubuntu 9.10 onto my Acer Aspire 3100 laptop, running it alongside Widows Vista as a dual-bootable system. Creation of the Ubuntu boot CD went fine, and the installation onto my hard drive was flawless. Ubuntu opens and behaves as I would expect, except for one little problem. For reasons unknown to me, Ubuntu is not communicating with my laptop's networking hardware, and I have no internet connectivity, it works fine under Windows Vista. Up in the right side of the Ubuntu desktop, I click on the network icon and it does not show a wireless connection at all. At home, where I use a dialup modem, I also see no means of getting online. My modem is an HDAUDIO Soft Data Fax Modem with Smart CP,manufactured by CXT (Conexant Systems Inc., file version 4.0.13.0, and the driver version is 7.58.0.0). I am an advanced computer user, but I am not a programmer. I seek a solution that is user-friendly for normal people, something equivalent to a driver that I can easily install or activate that will allow Ubuntu to see my hardware and get me connected. Can anyone help me over this hopefully-little glitch My processor is a Mobile AMD Sempron Processor 3500+ at 1.80 GHz, 1.50 GB RAM, and a 32-bit Operating System.

  Read the article

• For Windows XP: How to uninstall Broadcom Bluetooth software that won't disappear

  - by T. Webster

  Hello, my situation is similar to this question for Windows 7, except my OS is Windows XP SP3. I have recently realized I made the mistake of buying a Bluetooth adapter and installing the Broadcom/Widcomm Bluetooth stack driver software. Now that I know that the software is no good, I want to install it (so I can install the Toshiba stack for the Cirago adapter). I've attempted to uninstall all Bluetooth driver software in Device Manager, and I don't see any remnants of any Bluetooth drivers there. I would include pictures here, but I don't have 10 reputation yet, so I'll just use links instead. picasaweb.google.com/lh/photo/2NAos6BP9UigPtJKaYRGyQ?feat=directlink But I do see that the little Bluetooth icon still persists: picasaweb.google.com/lh/photo/kbxgPP8ZLxhjX4ob2YjSew?feat=directlink I don't see anything about Bluetooth, Broadcom, or Widcomm in Add/Remove Programs. I don't see any folder names Broadcom or Widcomm in Program Files folder, either. But I do see that Broadcom does show up in the registry with respect to Bluetooth, as shown here. picasaweb.google.com/lh/photo/hWDo-OzB8ApibzeHA_saxQ?feat=directlink What should I do now to completely wipe this persistent Broadcom Bluetooth software off my computer?

  Read the article

• External HDD incorrectly detected as internal - how change to enable hot swap/eject?

  - by Sam

  Hi All, I have win 7 x64 Home Prem. The HDD is a seagate barracuda, 7200.7 ST3120827AS. 3.5", Serial: 3ms006n6, Firmware: 3.42 (no further updates) NexStar CX External case (drivers installed). I have three drives: WD320 with OS installed WD750 data storage (internal) seagate 120 (external) - connected via esata board connected to sata on motherboard (MSI p43 neo) Tried uninstalling HDD in device manager to no effect. Also the internal WD750 is detected as an external drive and win taskbar icon allows for it to be ejected (unlike the seagate). All drives are configured - Online, Simple, Basic, NTFS, Active, Primary Partition (except c drive). The seagate was previously used as a primary disk with XP operating system so I deleted the volume and created/reformatted (not quick). HDD is no longer "Active". But did not fix problem. Background Originally, I installed win 7 with the bios set to IDE and forgot to install the chipset drivers. Then I changed win 7 to install the AHCI drivers, changed the bios to AHCI and rebooted. Win 7 loaded drivers but WD HDD gave problems/crashed. I installed chipset drivers and latest intell storage matrix software thingie (in safe mode). Everything worked fine after that except for the problem of not corrrectly detecting the external drive] I have noticed that under the driver properties (and similarly in the registry) the two drives are configured differently (e.g. in driver details property capabilities for the WD the value is set to 0000006, CM_DEVCAP_REMOVABLE & EJECTSUPPORTED - whereas the seagate shows 0000080 & CM_DEVCAP_SURPRISEREMOVALOK). Any easy way to configure things? I tried physically swapping the sata connections on the mainboard without success So far I have found that a solution to my problem might be to perform some reg changes: http://superuser.com/questions/12955/how-do-i-remove-the-option-to-eject-sata-drives-from-the-windows-7-tray-icon

  Read the article

• How can I remove all drivers and other files related to a USB Mass Storage device?

  - by Bob

  I have a flash drive here that does not work on one OS on computer - let's call it the desktop Windows 7. It works fine on another computer - laptop Windows 7. It also works fine on Windows 8 on the same desktop computer. Other flash drives work fine under desktop Windows 7. So not a hardware issue, not a generic USB Mass Storage driver issue. It's something specific to this drive. On desktop Windows 7, I can connect the drive but no volume comes up under Windows Explorer. Ditto for Disk Management. With diskpart, loading hangs until I unplug the drive, if I replug it and try list disk it hangs again. If I unplug the drive at this point, list disk prints out all attached drives - including the just removed flash drive. The drive consistently appears under Device Manager, but uninstalling the drivers, restarting and reinstalling the drivers (by inserting the drive) only works for the first insertion. After that it fails again. I get the feeling that the driver files are not actually removed, and are corrupted, meaning every reinstall it's the same corrupted drivers being installed. Is there any way to remove these drivers completely? Or perhaps some other setting Windows 7 retains? Formatting the drive through another computer/OS does not help. I've also tried a complete wipe and rebuild of the MBR and single partition. The allocation unit size makes no difference; neither does a NTFS format. This is a relatively small matter, and I would not like to reinstall the entire OS!

  Read the article

• HP Laptop recognizes hard drive just long enough to install windows

  - by Joe

  I have an HP laptop, DV6500 (CTO). It refused to boot one day, so I ran some diagnostics (a friend lent me "Hirens Boot Disk", "UBCD" and "PC DR 6"). Everything passed, except for the hdd. I replaced the HDD with a used drive of unknown condition. Installed windows with no problems. Installed the wireless driver, tried to reboot ... no luck. So I went to Best Buy, bought a brand new Western Digital 320gb HDD. Put it in the machine, installed windows (vista home premium). Installed the wired networking driver. Tried to reboot. No luck. Put the first hdd back in the machine, reinstalled windows. Started to install some drivers, went to reboot, and the machine won't come back to life. Put the second hdd in the machine, rinse wash and repeat. I've replaced the memory, even though it passed diagnostics. Problem exists with both brand new memory, and old memory. The BIOS recognizes the hard drive. The computer freezes directly after the bios splash screen, and there is no hard drive activity light. I've tried two linux live distros (gentoo and ubuntu). Neither would run on this laptop, but will on a different HP laptop. UBCD and Hirens Boot Disk both ran, as did PC Doctor 6 which refuses to test anything (gets stuck at "enumerating hard disks"). Is there anything else I can try?

  Read the article

• Why can't I get out of display mirror mode?

  - by Roy Smith

  I've been running Ubuntu (10.04.1 LTS, 64-bit) for a while and just replaced my hardware with a faster machine with an ATI Radeon HD 5700 video card. I've got twin 1920 x 1080 displays. I downloaded the latest driver (ati-driver-installer-10-9-x86.x86_64.run) from the ATI web site and installed that. I've gone through a few rounds of playing with /etc/X11/xorg.conf, and can't get things right. At the moment, it's in display mirroring mode, and I can't figure out how to get it out of mirror mode. If I run Monitor Preferences, there's a "Same image in all monitors" checkbox. If I uncheck that, the little preview window switches to show two monitors. When I click Apply, it asks me to log out and log back in again. When I do that, I'm right back to mirrored mode. What's really weird is that I'm currently running a copy of xorg.conf from a coworker's machine. He's got identical hardware, and his display works fine. So, I'm inclined to think there's something else going on other than the conf file. Any ideas what might be wrong?

  Read the article

• Ubuntu xrandr rotate issue

  - by user83544

  I've just bought a second monitor for my PC which happens to be a pivot monitor. I've already read lots of forums related to my problem but haven't come across a solution - I have the same symptoms as dozens of posts but no matter whatever I try it just doesn't work. I've already changed the xorg.conf file and added in the device section just under Driver "nvidia" the following for my second monitor: Option "RandRRotation" "on" When I save and reboot I try to rotate my screen with the nvidia X server settings by choosing the second monitor and clicking either "left" or "right" for the rotation. It immediately exits the nvidia settings window and does nothing. I tried within the terminal by typing: xrandr -o right I get the following error: X Error of failed request: BadMatch (invalid parameter attributes) Major opcode of failed request: 154 (RANDR) Minor opcode of failed request: 2 (RRSetScreenConfig) Serial number of failed request: 14 Current serial number in output stream: 14 I actually manage to rotate it with Option "Rotate" "CCW" instead of "RandRRotation". The problem with this solution is that you get the second monitor in the right position, but any window you open on that screen is practically unchangeable. You can't change the size nor move it, making it useless for reading PDFs, which is the main reason why I bought this second screen to help me write my thesis. Any help is really appreciated. sudo lshw -c video hiram@hiram-linux:~$ sudo lshw -c video *-display description: VGA compatible controller product: nVidia Corporation vendor: nVidia Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nvidia latency=0 resources: irq:16 memory:f8000000-f9ffffff memory:d8000000-dfffffff memory:d4000000-d7ffffff ioport:dc00(size=12 memory:fbd80000-fbdfffff

  Read the article

• How do I recover drivers from other hard disk

  - by Carl

  The drivers for a Cardbus (PCMCIA) card that gives me 2 USB 2.0 ports are on the hard disk from my old laptop. I have lost the driver CD. I have a way to get files from that other hard disk. Which files do I need? The drivers for the card used to be on the following website - the information is still there, except the download links don't work: http://www.ht-link.com/en/DownView.asp?ID=10 - The drivers I need are the first listing - The Win XP drivers for the HT-112NEC. My e-mails to them have not been answered. The information on this card is here http://www.ht-link.com/en/ProductView.asp?ID=106 I already tried connecting that other drive to my new laptop (via USB) and adding the drive to the search criteria when selecting update driver in the Device Manager. It says there isn't a better match, and if I select manual the matching device is not listed. (I don't think "manual" sees drivers on the external hard disk - but only ones on the main drive and/or found listed in the registry.) I would try 'have disk' if I knew exactly what file to point to on the external drive. The drivers are on that hard disk - I installed them there, and used that card on that computer. The new laptop has Windows XP Pro SP3, the old one had Pro SP2 Thanks for any help.

  Read the article

• Ubuntu 10.04 network manager issues

  - by Shark

  I was using the default network manager to connect to my wi-fi network, but if the connection is dropped or router restarted the network manager wont reconnect automatically after i guess a couple of tries and just gives a pop-up to connect manually . To avoid this annoyance I installed WICD but though it does try to reconnect to the network after a drop in connection it is unable to resolve the ip address and i am left with an even bigger annoyance . 1. Is there a way to counter either of these issues ? 2. Something like a background process that will check network status periodically and then try to connect to a favored network ? Edit- out put of lshw -C network *-network description: Wireless interface product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:12:00.0 logical name: eth1 version: 01 serial: c0:cb:38:18:9b:7f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.60.48.36 ip=192.168.11.2 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:fbc00000-fbc03fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:13:00.0 logical name: eth0 version: 02 serial: f0:4d:a2:94:2d:74 size: 10MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:29 ioport:e000(size=256) memory:d0b10000-d0b10fff(prefetchable) memory:d0b00000-d0b0ffff(prefetchable) memory:fb200000-fb21ffff(prefetchable)

  Read the article

• External HDD incorrectly detected as internal - how change to enable hot swap/eject?

  - by Sam

  I have win 7 x64 Home Prem. The HDD is a seagate barracuda, 7200.7 ST3120827AS. 3.5", Serial: 3ms006n6, Firmware: 3.42 (no further updates) NexStar CX External case (drivers installed). I have three drives: WD320 with OS installed WD750 data storage (internal) seagate 120 (external) - connected via esata board connected to sata on motherboard (MSI p43 neo) Tried uninstalling HDD in device manager to no effect. Also the internal WD750 is detected as an external drive and win taskbar icon allows for it to be ejected (unlike the seagate). All drives are configured - Online, Simple, Basic, NTFS, Active, Primary Partition (except c drive). The seagate was previously used as a primary disk with XP operating system so I deleted the volume and created/reformatted (not quick). HDD is no longer "Active". But did not fix problem. Background Originally, I installed win 7 with the bios set to IDE and forgot to install the chipset drivers. Then I changed win 7 to install the AHCI drivers, changed the bios to AHCI and rebooted. Win 7 loaded drivers but WD HDD gave problems/crashed. I installed chipset drivers and latest intell storage matrix software thingie (in safe mode). Everything worked fine after that except for the problem of not corrrectly detecting the external drive] I have noticed that under the driver properties (and similarly in the registry) the two drives are configured differently (e.g. in driver details property capabilities for the WD the value is set to 0000006, CM_DEVCAP_REMOVABLE & EJECTSUPPORTED - whereas the seagate shows 0000080 & CM_DEVCAP_SURPRISEREMOVALOK). Any easy way to configure things? I tried physically swapping the sata connections on the mainboard without success So far I have found that a solution to my problem might be to perform some reg changes: How do I remove the option to eject SATA drives from the Windows 7 tray icon?

  Read the article

• Windows 7 hangs on black screen for a while after log in

  - by steini

  I get the welcome screen. I click on my user and get the "logging on" screen. After that all I get is a black screen with a mouse cursor. I can't even start task manager. No ctrl+alt+del or ctrl+shift+escape. It stays like this for about 10 minutes, then the desktop finally starts loading. According to the hdd led on my case, windows isn't even trying to access the hard drive for that whole time. It's just hanging doing nothing it seems. What I have tried: Uninstalled video driver and removed leftovers with driver sweeper Disabled all startup programs and non microsoft services Loaded "last known good configuration" Ran the alleged "black screen fix" from prevx against my best judgement (don't really like running random exes without knowing what they do at all) None of that works. I can boot into safe mode normally. My specs: i7 920 Gigabyte X58-UD3R Gigabyte HD5870 1GB 12GB Mushkin Silverline 1333MHz Windows 7 Ultimate x64 I'm also having another problem which I suspect is related. After I have gotten the computer up and running, everything works perfectly, but when it's been on for a while it starts behaving strangely when changing display modes. When I start up a game or anything that changes the screen resolution the computer freezes for about a minute every time until I reboot again. I think this is probably related to the black screen problem. Just thought I'd check to see if anyone has had the same problem. Let me know if I should post any more details about my system to help diagnose this. Thanks in advance.

  Read the article

• Display issue with fresh install of windows server 2012

  - by Tony

  I installed windows server 2012 last night on my home "server". I use server loosely. From the get go I had display and graphic issues. The image was fuzzy and jumbled up during the install. This continued once booted into the install. I did installed Server 2012 twice now as the first time, I only installed "core". I know this is not a busted graphics card because it worked fine in Win7, during boot, and fine in "core" mode. Once booted into "GUI" install of Server 2012, the image was messed up again. To make things even more weird, the windows "loading" screen looks fine. Once the login screen appears the image is fuzzy and jumbled. My guess was that it was a driver issue. I did try to install the win8 x64 drivers from nvidia. This caused the system to become unbootable and I had to restore to a previous working point and uninstall the driver. I did try two different monitors and cables. Also both ports on the back of the video card. I did manage to get RDP running and that works fine. I rarely work directly on this machine but it would be nice to have the option back. Geforce 210, AMD 4600+, 4 gigs of ram.

  Read the article

• Using keyboard disables touchpad left button for a second on Acer laptop in Windows 8.1

  - by Robert Kilar

  The problem is present in the whole system not only in games: desktop, chrome, games, everywhere. When I press any "input key" on a keyboard for example in desktop I can't select the file by left mouse button OR by tapping the touchpad for about one second(right button works immediately). Later on the LMB works well. There is NO delay, button is just deactivated for a second. In games that means that when I run I cannot shoot for example. When I switched LMB and RMB functions in windows control panel still the LMB is getting disabled and RMB works fine. By "input key" I mean letter or a number, keys like Alt, CapsLock, Ctrl does not affect touchpad. I do not remember that problem when I used Windows 7. USB mouse works like it should. The problem existed when I was using Elantech touchpad driver and after I uninstalled it and used Windows 8.1 generic driver. EDIT I installed the Elantech drivers and set values to 0 at every disable... key. But the problem is still present. EDIT 2 THE LAPTOP IS Acer V3-571G I have turned off disabling function in touchpad but it did not fix it. I know that touchpad is NOT broken down. Turned on the animated touchpad icon of elantech drivers and put it on the task bar(on a picture) When I type the letter and press the LMB the dynamic icon displays the click but it is ignored.

  Read the article

• Many different BSOD

  - by Exa

  I'm experiencing multiple bluescreens for a couple of months now. Their error code is as diverse as their time of occurence... Sometimes it happens during gaming, sometimes when watching videos, sometimes when the computer is idle. These are the bluescreens I see most often: PAGE_FAULT_IN_NONPAGED_AREA KMODE_EXCEPTION_NOT_HANDLED IRQL_NOT_LESS_OR_EQUAL SYSTEM_SERVICE_EXCEPTION SYSTEM_THREAD_EXCEPTION INTERRUPT_EXCEPTION_NOT_HANDLED DRIVER_IRQL_NOT_LESS_OR_EQUAL DRIVER_OVERRAN_STACK_BUFFER Responsible drivers (according to the memory dumps): hal.dll tcpip.sys dxgmms1.sys ndis.sys mouhid.sys atikmdag.sys dump_atapi.sys and of course: ntoskrnl.exe My first thought was a driver incompatibility because I am using Windows 8 and some of the bluescreens seem to come from driver issues. All drivers are up to date. I'm afraid that my memory is broken or the mainboard or both. I used the windows integrated memtest which didn't find any errors. Memtest86 found some errors. Does it make sense to buy new memory? Couldn't it be a problem of the board as well? I also read that my memory could run at a too low voltage. But it's set to 1.5V as recommended. Another guess would be to set the memory's latencies manually, but how do I know which ones to try? Here is a screenshot of bluescreenview showing the latest bluescreens. Maybe someone has faced the same behavior before and found a solution. Any ideas or suggestions? Current setup on which the bluescreens occur. Windows 8 RTM (6.2.9200) Asrock 970 Extreme4 AMD FX-8150 ATI Radeon HD5850 16 GB RAM (DDR3-1800) Latest drivers for all devices

  Read the article

• Unable to set initcwnd on a Hetzner server

  - by Sergi

  We just ordered a bunch of Hetzner EX40SSD servers with the minimal Debian install image that they provide and everything is just fine except that looking at tcpdumps for fine tuning the network from various locations the initcwnd param seems to be stuck at 6 no matter how we change it. By default Debian 3.2 kernels should have that setting to 10 so it's pretty strange. Is it possible that the NIC driver or a custom setting in the Hetzner Debian image is limiting this param? Even if we set it to 4, like the old kernel default, it doesn't work. Any ideas would be much appreciated! Does anyone know if the NIC drivers provided by default by Debian have some kind on limitation. In a long thread in http://www.webhostingtalk.com/showthread.php?t=1200617&highlight=hetzner they talk about a page http://wiki.hetzner.de/index.php/Installation_des_r8168-Treibers/en where Hetzner states that the included Realtek r8168 driver is not working properly, but nowhere do they say that the initcwnd could be affected. Tomorrow i will try to install a CentOs image and see if Debian is the problem...Last resort would be to install a custom debian image, but that is a pain in the ass! Thanks!

  Read the article

• ASUS laptop doesn't charge/use the battery after reinstalling Windows 7

  - by Stan

  I've done a clean install of Windows 7 x64 on an ASUS X501A laptop. The battery is detected and shows in the system tray as "plugged in, charging". However the charge level stays at 76% and if the AC cord is plugged out the laptop turns off. The laptop does not turn on without being plugged in either. Everything worked perfectly prior to reinstall. I've tried: Downloading and installing all the ASUS drivers, including the ATK ACPI driver Checking the BIOS - there do not seem to be any battery-related settings Flashing the BIOS to the latest version Uninstalling Microsoft ACPI-Compliant Control Method Battery in device manager as suggested on the internet Full power discharge/ATX reset as suggested by ASUS support: remove mains power charger, remove battery, press and hold power button for 10 seconds, reconnect battery and mains and turn on I have a feeling all this may have something to do with the EFI BIOS that comes on the laptop. During the reinstall I had to delete all partitions and start anew, because the Windows installer complained about the improper order of GPT partitions. The EFI System Partition was recreated by the installer, and I am guessing that it may be missing the particular ACPI driver needed to make the battery work. I've tried researching this, but could not come up with any useful info. I am hoping someone here may know a bit more about this and maybe help me understand what's going on and how to fix it. Barring that, I'll have to re-image the drive off an identical ASUS laptop with stock install and hope it fixes things.

  Read the article

• Which program is locking all my executable files?

  - by Tom Wijsman

  When updating any software product, as well as manually trying to replace .exe files, it says that access is denied to the file and in fact the System process is holding a handle to the file when I check it with Process Explorer. This must be a driver or something that is malfunctioning was my first though, but now I wonder how I figure out which driver / program is doing this and why it is so. Unlocker doesn't seem to be working for me, unless someone can tell me how to use it properly other than making it appear a magical wand in the notification area.... This is what Unlocker puts in my event log: The description for Event ID 1060 from source Application Popup cannot be found. Either the component that raises this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on the local computer. If the event originated on another computer, the display information had to be saved with the event. The following information was included with the event: \??\C:\Program Files (x86)\Unlocker\UnlockerDriver5.sys the message resource is present but the message is not found in the string/message table Upon searching event 1060 I get: <file name> has been blocked from loading due to incompatibility with this system. Perhaps it is because I have 64 bit?

  Read the article

• Dovecot starting and running, but not listening on any port

  - by Dženis Macanovic

  Among others things I'm in charge of a Debian GNU/Linux (Wheezy) DomU for the mail services of the company i work for. Yesterday one HDD that was used for this particular server has died. After installing Debian again, Dovecot decided to no longer listen on any ports (checked with netstat -l). Other services (like Postfix and MySQL) work without problems. dovecot -n: # 2.1.7: /etc/dovecot/dovecot.conf # OS: Linux 3.2.0-3-amd64 x86_64 Debian wheezy/sid ext3 auth_mechanisms = plain login disable_plaintext_auth = no first_valid_uid = 150 last_valid_uid = 150 mail_gid = mail mail_location = maildir:/var/vmail/%d/%n mail_uid = vmail namespace inbox { inbox = yes location = prefix = } pass db { args = /etc/dovecot/dovecot-sql.conf.ext driver = sql } plugin { sieve = ~/.dovecot.sieve sieve_dir = ~/sieve } service auth { unix_listener /var/spool/postfix/private/auth { group = postfix mode = 0660 user = postfix } unix_listener auth-userdb { group = mail mode = 0666 user = vmail } } service imap-login { inet_listener imaps { port = 993 ssl = yes } } service pop3-login { inet_listener pop3s { port = 995 ssl = yes } } ssl_cert = </etc/ssl/private/mail.crt ssl_key = </etc/ssl/private/mail.key userdb { args = /etc/dovecot/dovecot-sql.conf.ext driver = sql } protocol imap { mail_max_userip_connections = 25 } UID 150 is vmail (I double checked file permissions). I didn't install Dovecot from source, but via apt from the official Debian US mirror. There are no messages concerning Dovecot in /var/log/syslog except for: Oct 21 06:36:29 server dovecot: master: Dovecot v2.1.7 starting up (core dumps disabled) Any ideas?

  Read the article

• ATI Radeon 5670 Won't Show Resolutions over 1400x900

  - by Phil Sandler

  Just got my new Dell computer with Windows 7 and an ATI Radeon 5670. I attached it to my current monitor, which is a Samsung 24" (2443bwt). Windows 7 does not allow me to display in resolutions greater than 1400 x 900. The setup through a VGA cable into the VGA port of the card. The card also has a DVI port, but I need to use the VGA port because a KVM that supports VGA only. My old PC (which is Windows XP, GeForce 8600 video) can display in 1900 x 1200 on the same monitor (which is what I want) and even higher. It does this through a vga cable also connected to the KVM (through the DVI port but using an adapter). I have tried the same setup (DVI = VGA adapter) on the new PC and nothing changed. I have tried: Updating the drivers via Windows "Update Driver" (says they are current) Installing the updated version of the drivers from ATI (made no difference) Installing Powerstrip (all the options I would need for a custom resolution are greyed out) Installing the drivers/software from ATI caused the ATI Catalyst Control Center software to stop functioning, so I can no longer even start it. I have found some references to other people having this problem and instructions on cleaning the software off and reinstalling it (as uninstalling normally doesn't solve it). I will try this tonight. In any case, I didn't see any options in CCC that would allow me to override the settings for max resolution. However I didn't tinker with it too much before I tried updating the drivers, so I may have missed a setting. I contacted Samsung via online chat and they say it's a problem with the video card/driver (of course--what else would they say?). Any thoughts on what else I could try?

  Read the article

• WIN7 constant BSOD 0x7B on boot, not producing any dump files where to go from here?

  - by prayingpantis

  So my one win 7 pc has been getting a BSOD on boot (roughly a sec after load screen starts) after a power failure. The complete stop code is 0x0000007B (0x80786B58, 0xC0000034,0x00000000,0x00000000) I've searched for quite a while now on the net and it seems like most people gave up after gettting 0x7B and no dump files. What I've tried so far: startup repair - reports it cannot repair computer automatically. BadPatch is reported somewhere in a problem signature contained in the problem details. startup repair with a WIN 7 CD - also fails, I can't recall what the error was, but it was not the same as the error produced with the start up tool shipped with the version of WIN 7 installed on my machine (I think the text had something ACL-ish contained in it) used a boot disk (Hiren's boot iso) - I used it to enable the CrashDump registry key and then after BSOD, read the HDD's dump locations but it was empty. Note, I'm quite sure the registry keys I edited are the correct ones, since the reboot on BSOD option was enabled by default and after I changed the regkey controlling this functionalitty to 0 the BSOD stayed after I booted again. check disk - works and returns no problems, also it seems I'm able to access all my files on the HDD. mem test - works and returns no errors So I'm not sure what else I can do to figure out what is the problem here. I read somewhere that you can use WINDBG to remote debug another PC, but I'm not sure if this is possible since the OS isn't even loaded yet? Also the last driver change I made on the system was installing a video driver, but I had no problems with it and were able to reboot several times until the power outage happened and the BSOD appeared. Any help or guidance for a way to DEBUG this problem would really be appreciated (I'm not really that keen to try a whole bunch of random fixes, I'd rather try and narrow down the problem first).

  Read the article

< Previous Page | 111 112 113 114 115 116 117 118 119 120 121 122  | Next Page >