Search Results

Search found 23946 results on 958 pages for 'remote computer'.

Page 116/958 | < Previous Page | 112 113 114 115 116 117 118 119 120 121 122 123  | Next Page >

• Internet Dropping?!

  - by stead1984

  I have a virtual DC running DNS and Routing and Remote Access, that routes ALL workstations Internet traffic out to the Internet, this works fine but noticed that the Internet drops occasionally. I've checked with our service provider (Managed Communications) and they are adamant that it's not their fault. The Internet drops seem to affect everyone. We also have a server configured to use the same Internet service on a different network over a site-to-site VPN connection which also suffers from packet drops. I've spoken to Cisco and have done many tests with Cisco and they believe the problem is down to the ISP. I'm wondering if it's a DNS issue, as the Internet service uses OpenDNS. Any ideas?

  Read the article

• Why are network printers not available in the Add Printer Wizard...when run over a network?

  - by Kev

  From a Windows 2003 server machine I browsed the network to an XP client (\computername in Explorer) then double-clicked Printers and Faxes and then Add Printer. In the wizard, normally the second screen asks if you want to install a local printer or a network printer. Well, in this case, it seems to assume I want a local printer, because the second screen is what would normally be the third screen if you chose local printer and clicked Next. I want to install a network printer on a remote machine for its local users. Is this not possible? If not, why not?

  Read the article

• RDP for High DPI Monitors?

  - by Joey

  A client is having some problems with their laptop. They use RDP to remote into their work PC, but the laptop they are using is a small 13" Sony Vaio laptop, but with 1920x1080 resolution. Everything is pretty small on the laptop anyway, but the problem is much worse after connecting with RDP, where everything is almost unreadable. I have done the obvious with changing the resolution on the server, the RDP size, forced scaling on the terminal server etc, but nothing has worked. Something else which I would normally do is change the laptop resolution to something a little lower, but the laptop only has 2 resolution settings, the big one, and a 1024x768 (wrong ratio). Any ideas?

  Read the article

• Share one monitor with another user and display their screen as well

  - by Xiong Chiamiov

  My housemate and I just started playing the original RollerCoaster Tycoon again - what a nostalgia trip! Anyways, we both have two monitors, and would like to view the other's game on the secondary monitor while playing, since we're in different rooms. VNC-like applications sorta work, but they require two separate instances running (one to share each direction), and as a whole are rather slow and clumsy. We don't need any remote control at all, just viewing. I'm using XP, he Win7. We could probably get it to run through some means in Linux, if necessary.

  Read the article

• Windows scheduler - Tasks not running when user not logged in

  - by Glinkot

  I have Windows Server 2003, with schedules setup via Remote Desktop under one account. That account appears in the 'creator' column too. I have 'Run only if logged on' unticked. When I have logged in under that account and then 'disconnected' leaving the the session alive, the schedule runs. But every time the server is rebooted, the task again fails to run until I again log in and disconnect. Any KB fixes I've missed or issues I've overlooked? Normally I only discover the issue when a user tells me the schedule has stopped running so it's a real reliability issue. I'd also be happy with an answer suggesting an alternative scheduler with higher reliability. Thanks

  Read the article

• Windows Server 2008: Terminal Services / VDI

  - by JohnyD

  I have a Dell R710 with 72GB of memory running Hyper-V. Within Hyper-V I have a Windows 2008 (32-bit) VM running Terminal Services. How do I allocate memory so that any user who connects to this Terminal Server (from their thin-client) is allocated 2GB (or whatever amount I choose) of memory? Currently I have provisioned the TS with 2GB of memory but it seems that this is shared among all that connect. Please let me know if there is further information I can provide. Thank you. Update 1: What I'm looking to accomplish with this server is setting up a VDI to allow users to connect from thin-clients from within our network. They will also have to connect from outside our network via VPN which is already in place. Am I able to set this up using Windows Server 2008 (not R2) because I have a 16-bit application which needs to be supported. Unfortunately it's not a candidate as a Remote App.

  Read the article

• access VPN machine macosx same subnet

  - by matheszabi

  I would like to access the office machine, which has a fixed IP, and is available only in its local LAN. Let say 192.168.1.100. I have a VPN with username/password connection and I am trying to access the office machine from another location, i.e., another LAN, which has the same subnet: 192.168.1.50. I am using MacOSX 10.8. I have checked the "send all trafic over VPN connection, but I think it looks like it doesn't care and is searching in Local. I do not have admin privileges and can't request to make changes to the network settings in both LANs. Is there any way to connect to the desired remote machine?

  Read the article

• How to make VirtualBox headless answer on rdp port?

  - by stiv

  I'd like to run windows xp on RDP: $ VBoxManage modifyvm winxp32 --vrdeport 3389 $ VBoxHeadless -s winxp32 -v on Oracle VM VirtualBox Headless Interface 4.1.18_Debian (C) 2008-2012 Oracle Corporation All rights reserved. (waiting) in another window: $ telnet localhost 3389 Trying 127.0.0.1... telnet: Unable to connect to remote host: Connection refused Yes, I've read about extension: $ sudo VBoxManage extpack install Oracle_VM_VirtualBox_Extension_Pack-4.1.20-80170.vbox-extpack 0%... Progress state: NS_ERROR_FAILURE VBoxManage: error: Failed to install "Oracle_VM_VirtualBox_Extension_Pack-4.1.20- 80170.vbox-extpack": Extension pack 'Oracle VM VirtualBox Extension Pack' is already installed. In case of a reinstallation, please uninstall it first Looked through all manuals and all help requests. No success. What's wrong? Any ideas?

  Read the article

• Can I increase the link speed of the RAS Server on our MS Win2k3 box?

  - by Ducain

  We are running a Win2K3 Server box, and I'm a remote employee that connects via VPN. I've been frustrated for some time by the connection speed over the VPN (the office HQ has a decent speed and I have a biz class connection here), and decided to do some checking today. This morning, I was dialed in and looked at the networking tab of the task manager, and I see that the adapter for the RAS Server (the box has 4 Gigabit adapters) has a speed that seems far too low. The speed for the RAS Server link hovers between 300 - 600 Kbps. The local connection (and others) all say 1 Gbps. Can I set this to a higher speed? Is this information accurate? Thanks for the input.

  Read the article

• Network-Backup-Software with file versioning and web-interface

  - by dlang

  Dear All! I would like to backup our business-data to a remote backup-server. We would like to set-up our own backup-server running on any operating system (windows appreciated) which comes with a web-interface, that enables to restore individual versions of one file. Because budget is limited, an open-source software or at least a cheap software is a must! Unfortunately I couldn't find even a single software, which fulfills the requirements of file versioning and web-interface for single file-restore. Do any of you have already set-up such a system? Best regards, Daniel Lang

  Read the article

• Execute local script requiring arguments on Linux via plink

  - by c_maker

  Is it possible to execute (from windows) a local script with arguments on a remote linux system? Here's what I got: plink 1.2.3.4 -l root -pw mypassword -m hello.sh Is there a way to do this same thing, but able to give input parameters to hello.sh? I've tried many things, including: plink 1.2.3.4 -l root -pw mypassword -m hello.sh input1 input2 In this case it seems that plink thinks that input1 and input2 are its arguments.. which makes sense. What are my options?

  Read the article

• How to remotely install Linux via SSH?

  - by netvope

  I need to remotely install Ubuntu Server 10.04 (x86) on a server currently running RHEL 3.4 (x86). I'll have to be very careful because no one can press the restart button for me if anything goes wrong. Have you ever remotely installed Linux? Which way would you recommend? Any advice for things to watch out? Update: Thanks for your help. I managed to "change the tires while driving"! The main components of my method are drawn from HOWTO - Install Debian Onto a Remote Linux System, grub legacy: Booting once-only, grub single boot and kernel panic reboot , and Ubuntu Community Documentation: InstallationFromKnoppix Here is the outline of what I did: Run debootstrap on an existing Ubuntu server Transfer the files to the swap partition of the RHEL 3.4 server Boot into tha swap partition (the debootstrap system) Transfer the files to the original root partition Boot into the new Ubuntu system and finish up the installation with tasksel, apt-get, etc I tested the method in a VM and then applied to the server. I was lucky enough that everything went smoothly :)

  Read the article

• How to enable RDP to a Server 2008 R2 on another network? VM network

  - by Saariko

  I have a W2008 R2 installed on a different network (I am on 192.168.0.x - new server on 192.168.3.x) I had trouble ping and RDP to it. I disabled the firewall to test the connection: and that opened the ping feature but I still can not RDP to that machine. the allow remote access is enabled As per sinni80 idea - Here is the error message The networks are divided by a Fortigate 60-B router - 2ndy interface for the gateway is 192.168.3.254 (and pingable from all) any to any rule on both networks is in place. As per Joe Schmoe idea - I am able to RDP to 192.168.3.1 from 192.168.3.3 (which is on the same network) Data to add: - The servers are on a VM host, each of the servers has 2 nics one is DHCP enabled into the 192.168.0.x network 2nd is static IP in the 192.168.3.x -- Further information: The network 192.168.0.x - are on a domain network (active Directory) The network 192.168.3.x - are grouped in a workgroup What should I check more please?

  Read the article

• Ways to remotely reboot a Linux system

  - by dualed

  I had a remote server running Debian Sarge that experienced some HDD failure and I meant to reboot it hoping that fsck could repair the errors automatically. I eventually drove out there and replaced the faulty disks... But I was wondering: What other ways are there to force a Linux system to reboot that do not require hard drive access? What I had tried: shutdown -r now Did not work, as shutdown is a program that would have to be loaded from disk, the error shown in the terminal was bash: /sbin/shutdown: Input/output error init 6 same as above telinit q same as above kill -2 1 This did not print an error, but did not work either. (However, it is possible that the Sarge init did not implement SIGINT, the sarge manpages did not mention it. So it could work in a more recent version of Debian) This guide on PCFreak.net. However, this failed at sysctl, which was not in memory either.

  Read the article

• Will restarting the W3SVC Web Publishing Service, also restart the app pool in IIS?

  - by Mark Rogers

  Background: I'm trying to stop and start IIS on a windows 7 build box, in order to run acceptance tests. But from what I have read, most of the remote web management features have been disabled by Microsoft in a retarted attempt to sell more Windows Server 2008 licenses. Still for some reason they didn't disable the least user-friendly ways of controlling IIS remotely, but they are all a total pain. What I can do easily is remotely stop and start the WWW service from a msbuild task. But I want to be sure that this also restarts the app pool, so that when I copy in new web files the web server there will be serving the most recent version of the website. Question: If I restart the W3SVC windows service, will that also restart the app pool?

  Read the article

• Thunderbird + Gmail, has to send emails twice.

  - by Mohammad

  I've configured Thunderbird to place a copy of my sent emails in my remote "sent" folder of my Gmail account as opposed to the local thunderbird one. This ensures I can completely take advantage of my imap synchronization. And so whenever I send an email, it first sends one to the address list, then it sends a new one to my sent box, however doing this with large attachments seems like a waste of time and bandwidth. Do you guys know of any extension or a combination of a trick plus a Gmail filter that could automate this in one step?

  Read the article

• Disable/configure Back and Forward through mouse wheel in Internet Explorer

  - by Subtwo

  I have a problem with Internet Explorer (version 7 on Windows XP). Sometimes (not always) when you use the mouse wheel to scroll a page up/down it instead chooses to go back or forth in the web browsing history. This behavior is the same as when you hold the shift-key simultaneously using the wheel. My guess is that Internet Explorer somehow gets misled by something and thinks that I'm actually pressing shift. This is in turn maybe an artifact of the fact that this particular session is a remote-desktop session originating from Linux (Ubuntu). Needless to say the problem can be quite irritating and the alternative of completely turning off the wheel functionality doesn't seem like an option as other applications would suffer greatly from this. Anyway back to my question(s): Is it possible to map the shift+wheel to a simple wheel event for Internet Explorer? Is it possible to disable the shift+wheel event for Internet Explorer? Any suggestions are greatly appreciated.

  Read the article

• Remotedesktop to windows 2008 server with 2 nics

  - by The_Mo

  Hi I have 2 NICs on a Windows 2008 R2 Server. nic1 with ip address 192.168.2.1 with gatewaty 192.168.2.254 and nic2 with ip address 10.96.6.253 with no gateway. The windows 2008 server is connected to a router which is connnected to another router so if I want to connect to the windows 2008 server I use 192.168.0.31 because it is forwarded. If I use remote desktop to connect to that machine I use 192.168.0.31 and that works well, but the server has a seccond nic and I want to be able to connect with a remotedesktop to nic2. Any help appreciated! [server windows 2008 r2 192.168.2.1] -- [router 192.168.2.254/192.168.0.31] -- [my computer 192.168.0.13 gateway 192.168.0.254]

  Read the article

• How to locally resume a session that has been started remotely using xrdp?

  - by Jaroslav Záruba

  Can I connect to a RD session that has been started (and abandoned) from a remote machine using xrdp? Also I'd like to be able to do the exact opposite: to remotely login to a session that has been initiated locally. I'm trying to get as close as possible to how Windows RS behaves. (Which also includes that the session would use my terminal machine/monitor resolution. I wasn't able to achieve that using VNC.) Suggestions to a better alternative to xrdp are welcome please. I don't know Linux too much.

  Read the article

• %sessionname% returns incorrect session name

  - by Samuel Walker

  I have a virtualised Windows XP SP3 machine, which I am connecting to over Remote Desktop. One of my scripts needs to use the %sessionname% variable. However this returns incorrect information. C:\>%sessionname% constantly returns RDP-Tcp#5, instead of the value for the currently connected session (RDP-Tcp#35 or similar), as shown in Task Manager This causes my scripts to contain incorrect information. What can I do to resolve this? Edit Further Information: A restart appears to solve the problem for the first connection, but then subsequent connections have the numbers fall out of sync again.

  Read the article

• Problem connecting with RDP between Mac and Win2k3 server

  - by salle55

  I have an iMac running Mac OS X 10.5.8 and the RDP Connection Client 2.0.1. http://salle.dyndns.org/misc/rdp%5Fproblem1.png When I try to connect to a Windows 2003 Server on the same network I get a dialog saying "Remote Desktop Connection cannot verify the identity of the computer that you want to connect to". Picture: salle.dyndns.org/misc/rdp_problem2.png And when I press the Connect-button in the previous dialog I get the same message in another dialog: Picture: salle.dyndns.org/misc/rdp_problem3.png I can connect to the Win2k3 server from a Vista machine, and it used to work from the Mac as well. I stopped working from the Mac after I did some configuration on the win2k3 server, removed and added the the connection in the Terminal Services Configuration: Picture: salle.dyndns.org/misc/rdp_problem4.png What do I need to do to be able to connect from the Mac again? (I have not enough reputation to post multiple links or images)

  Read the article

• Default user logon on Windows Server system

  - by Robert Koritnik

  I installed Remote Desktop Services role (ex Terminal Services) on my Windows Server 2008 R2 machine. After installation when I try to logon locally, there's no default user as it used to be. Can I tweak group policy to have my default user back? I did enable to remember last logon user, but it didn't work... Obviously RDS (ex TS) ignores this policy setting. Additional note: I'm not connected to a domain. It's a standalone development machine running server OS. No domain needed for it.

  Read the article

• Set Up Port-Forwarding on Netgear N300 Router

  - by Smitty

  I have a Netgear N300 router that has DynDNS.org as a preset DDNS option. After setting it up it (unsurprisingly) sent traffic directly to my router. I'm essentially using this to connect remotely to my home (virtual) machine/s. From what I've read, it seems like I need to set up port forwarding. I tried forwarding "all" inbound traffic to a specific IP but that just didn't work. What am I doing wrong? Also, I just noticed I get this error after applying the settings: "The specified port(s) are being used by other configurations. Please check your configurations of Remote Management, Port forwarding, Port Triggering, UPnP Port Mapping table, RIP, and Internet connection type"

  Read the article

• file:// command-line arguments

  - by Cory Grimster

  Is it possible to pass command-line arguments to a program that is invoked via a file:// url? I'm trying to include Remote Desktop links in a wiki page that lists some servers: <a href="file:///c|/windows/system32/mstsc.exe /v:serverName">serverName</a> When I omit the argument the link works fine, but when I include it the link doesn't work. I Googled around a bit and couldn't find any references to this. I suspect that the answer is that file:// urls simple don't accept arguments (I can think of all kinds of ways to abuse them if they do), but I thought I'd throw it out there in case I've simply got the syntax wrong. Thanks.

  Read the article

• When RDP as a Domain User, Smart Card Requested

  - by Paul

  My W8 machine is connected to domain zen. If I rdp to the W8 machine, I can log in as a local user without problems. If I try to log in as a domain user, I am prompted for a smart card instead of a password. Any ideas why? Note that Interactive login: require smart card is disabled in group policy: And here is the output from rsop.msc: Some additional information on this one. If my connecting machine is on the same domain/network as the W8 machine, then I am prompted for a password as usual. If the machine is remote, on a different domain, then I am prompted for a smart card. In addition, the machine I am connecting from that gets the smartcard prompt is an XP box. I haven't isolated exactly which of these factors triggers the different response.

  Read the article

< Previous Page | 112 113 114 115 116 117 118 119 120 121 122 123  | Next Page >