Search Results

Search found 3909 results on 157 pages for 'brand newbie'.

Page 119/157 | < Previous Page | 115 116 117 118 119 120 121 122 123 124 125 126  | Next Page >

  • Do registry issues with Win7 persist through a recovery from a system image?

    - by user59089
    So I need a bit of advice, please; here's my situation: I have 1) a system image on an a brand new external 1 TB SATA drive, that I managed to successfully capture before my 2) primary system drive went down. I realize this is a fairly simple matter of buying a new primary drive and performing the recovery to the fresh disk...however, the issue is that I believe Win7 was also having some significant issues of its own--basically, Update unable to install updates, and Backup continually ditching the auto backup schedule. I'd been trying to address those issues when my system was still working, but it's been so fruitless, I'm convinced a Win7 re-install would be best, and now I'm concerned that if I was in fact having what I believe are likely registry-related issues before, that these will persist through a recovery--would that likely be correct? I'm mainly worried about recovering my files, so if I did a full recovery from the image, should I be able to then access my individual files, and copy them manually to an external drive, so I can then do a full re-install of Win7? Sory if this seems obvious, but I've never done a recovery before and just trying to make sure there's no red flags with what I have in mind...

    Read the article

  • Distorted Sound

    - by BCable
    I have my laptop hooked up to my receiver for sound output. I hear a hissing/crackling background sound that is really loud and hard to just ignore (but possible). When my 360 is connected, the sound comes out perfect, so it's just with this laptop. Previously, I thought it was just my laptop and just submissively just let it slide. I just bought a brand new laptop though and it's doing the same thing. I have found out more information now that I know it's not my laptop. I have used this laptop in similar environments where it worked just fine (different speakers). I have bought a new cable to connect to my receiver and it did nothing (headphone jack to RCA). I tried different ports on the receiver (Video 1-3) and it always happens. I have discovered that the sound goes away if I unplug my laptop (so it's running on battery). Because of the last one, I tried plugging my laptop into a different outlet across the room and it's STILL doing it. Doesn't matter if I boot to Linux or Windows, yet my phone (Android G1) doesn't cause this sound using the exact same cable. Any ideas? I'm out of them! Thanks!

    Read the article

  • How to configure router to give XBox top priority / most bandwidth?

    - by MrSparky
    Hi all - Newbie here so go easy... and apologies in advance if I blow the community etiquette / rules! Here's what I'm trying to do: I have a "D-Link DIR-655 Extreme N" wireless router and an XBox 360 w/ the old-style wireless connection thing (usb attachment)... I want to configure my router / network to give my XBox as much bandwidth as it wants, whenever it wants. I have tried giving the XBox a unique IP (within my network) and then tweaking the router to treat that IP as a top priority application (using the router's QOS stuff). Problem is whenever I turn off the xbox, I can't connect to the network the next time I start it up. It seems the only reliable setting in the XBox is to use "Automatic" for the IP settings within the Network Configuration area. Supposedly the D-Link ships with default settings that attempt to recognize a game console and give it top priority... but i've not seen good results (lots of stuttering / lag when someone else jumps online, etc). Any suggestions? thanks again!

    Read the article

  • Very slow connection to xserve via afp or smb

    - by Mhoffman13
    Help. File transfer and connection speed to our Xserve are painfully slow from newly purchased iMacs. The Xserve is only used as a file server, its running 10.4.11. The problem seems to be only happening on brand new iMacs running 10.6.3. When connected either over afp or smb copying files is many times slower than usual. Other machines on the network running either 10.4 or 10.5 have a normal connection speed. To try to rule out OS incompatibility I connected the new iMac running 10.6 to another computer running 10.4 over the network. The file transfer speed was fast as normal. So it seems the problems lies with the X serve (maybe). The afp logs either access or error don't show anything unusual. One thing that did look different was when the imac was connected to the Xserve the user had its id listed as its IP address. The other machines connected, had the id of broadcasthost. I also noticed that when connected from the new iMac I can only see one of the mirrors. When any other computer connects both mirrors are shown. Tried a restart of the Xserve but the problem persists. Thanks in advance for any advice

    Read the article

  • Limiting access in Silverlight\Pivotviewer

    - by sparaflAsh
    I'm going to deploy a pivotviewer application. As some of you might know this silverlight application load a .cxml index file for a group of images. My need is to make .cxml file and image files not accessible for the user. Now, if I don't have a need I usually code like this in C# and the file is hosted in the documentroot: _cxml = new CxmlCollectionSource(new Uri("http://www.myurl.it/Collection.cxml", UriKind.Absolute)); This means that my cxml and then the images are available by http for everyone who knows the URI. I'm a newbie to server configuration, so any help/hint would be deeply appreciated. Someone suggested me to take the files out of the root, but it seems like I can't go to pick them up if they are not a URL in Silverlight. At least I didn't managed to understand how. Someone else suggested me to play with web.config file to hide URLs, but I don't really know where to start. My question is, what's the best practice to hide my stuff? Obviously I can edit the question if you need more details.

    Read the article

  • Apache Process question about RAM usage

    - by Andrew Fashion
    So everytime I load a new page, I notice a new HTTPD process opens, every time I click a page, and each process says it's using anywhere from 2-4.5% of memory. Does that mean every single process is running at that time using 2-4% of RAM? It's a brand new server and I'm the only one on the server at the moment. Or does it mean all the other processes are dying, and only the new one is active. Because 4% of my 2048MB of RAM is already 82MB for just one process!?!? Let me know, because I am trying to determine what I need to beef my server up in order to handle high loads of traffic. I'm expect to get 20,000 uniques per day on launch. I am currently running a Dual Quad Xeon server, with only 2GB of ram, I will upgrade to 8GB or more shortly. Let me know what you suggest! thank you [root@D18634 log]# top | grep 'httpd' 11315 apache 15 0 362m 82m 24m R 12.3 4.1 0:03.00 httpd 11310 apache 16 0 322m 41m 21m S 5.7 2.1 0:02.98 httpd 11315 apache 15 0 362m 83m 25m S 24.3 4.1 0:03.73 httpd 11319 apache 16 0 324m 42m 20m R 1.0 2.1 0:01.85 httpd 11319 apache 16 0 362m 82m 23m R 78.5 4.1 0:04.21 httpd 11321 apache 16 0 323m 44m 23m S 35.3 2.2 0:04.13 httpd 11319 apache 15 0 361m 82m 23m S 8.3 4.1 0:04.46 httpd 11321 apache 15 0 323m 44m 23m S 35.9 2.2 0:05.21 httpd 11313 apache 15 0 324m 41m 19m S 48.6 2.1 0:03.23 httpd 11322 apache 16 0 354m 72m 20m R 11.0 3.6 0:05.11 httpd 11322 apache 16 0 354m 72m 20m S 23.9 3.6 0:05.83 httpd 11314 apache 16 0 355m 75m 22m R 18.3 3.7 0:04.64 httpd

    Read the article

  • SSH traffic over openvpn connection freezes when I cat a file

    - by user42055
    I have an openvpn (version 2.1_rc15 at both ends) connection setup between two gentoo boxes using shared keys. it works fine for the most part. I use mysql, http, ftp, scp over the vpn with no problems. But when I ssh from the client to the server over the vpn, weird things happen. I can login, i can execute some commands. But if i try to run an ncurses application like top, or i try to cat a file, the connection will stall and I'll have to sever the ssh session. I can, for example, execute "echo blah; echo .; echo blah" and it will output the three lines of text over the ssh session fine. But if i execute "cat /etc/motd" the session will freeze the moment I press enter. I compiled openvpn 2.1.1 on my mac and copied over my config directory from my gentoo client. The mac connected and ssh sessions worked fine without freezing. I then compiled it on my older gentoo box (2.6.26 kernel) which I am retiring due to a dying hard drive, and ssh over it also works perfectly. Why does it fail on my brand new gentoo box ? I've tried compiling three different kernels in case it was that, but other than that there should be no difference between my older and my newer gentoo boxes that I can think of. Any suggestions on what's wrong ?

    Read the article

  • Home server hard drive: 186k start-stop cycles in 325 days?

    - by j-g-faustus
    I set up a home server about a year ago, using Ubuntu server (10.04 LTS at the moment), four disks in RAID 5 for storage (WD Green 1.5 TB) and a laptop drive for the OS. Today the output of smartctl, a command line utility for checking the SMART attributes of a hard drive, tells me that the primary OS drive has had no less than 186,000 start-stop cycles in 325 days and may be nearing the end of its lifespan. The smartctl output is in "normalized values", in this case a number between 200 and 000, where 200 is "brand new" and 000 means "worn out". My disk gets 001. So I wonder what happened: 186k start/stop cycles in 7820 hours is about one start/stop per 2.5 minutes around the clock. This seems somewhat excessive for a computer that sees actual use once or twice per day. (The RAID disks are normal, averaging to one start/stop per day, as expected.) Does anyone have similar experiences, or pointers to what might be the issue here? Specifically I'd like to know Why the massive start/stop count? Do I have some sort of configuration issue? Could there be a background service that is causing trouble? Could having a laptop disk as the OS drive be part of the problem? Can anyone confirm or deny this? Here is the /etc/hdparm.conf configuration /dev/sda { apm = 127 spindown_time = 120 } and the most relevant parts of smartctl --attributes /dev/sda: smartctl version 5.38 [x86_64-unknown-linux-gnu] Copyright (C) 2002-8 Bruce Allen === START OF READ SMART DATA SECTION === SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 001 001 000 Old_age Always - 185875 9 Power_On_Hours 0x0032 090 090 000 Old_age Always - 7820 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 109 193 Load_Cycle_Count 0x0032 118 118 000 Old_age Always - 246833 194 Temperature_Celsius 0x0022 107 098 000 Old_age Always - 36 As I generally prefer my drives to last more than a year, any advice is appreciated.

    Read the article

  • Deployment and Ownership issues

    - by kylemac
    As an extreme newbie, I am having difficulty managing ownership and permissions on my first box. What I can't figure out is how to deploy using one user, we will call him deploy and operate my php application with www-data user. Currently as it stands, I know my server runs as www-data through this function <?php echo(exec("whoami")); ?> but I am having to chown between deploy and www-data every time I deploy. There has got to be an easier way to deploy with one user and still run as www-data. EDIT: Here is the output from ls- l on the folder in question. You will see user deploy and group www-pub, the group is from an attempt to add the two different users to a new group and chown one of them in the hopes that they both would have the permissions (newb alert) drwxrwxr-x 4 deploy www-pub 4096 Mar 7 01:41 example.com I am using capistrano for deployment under the user deploy then once its done i chown to www-data, otherwise I can't use php to manipulate files. I am also unsure how to even change which user apache is running.

    Read the article

  • vmdk Recovery after migration from 3.5 to 4 and fallback tentative.

    - by olgirard
    Hy, I've tryed to migrate some VM from my 3.5i environment to a brand new vSphere 4.0 U1. The two platforms are running simultaneously, sharing the same SAN. I Migrate my VM by stopping it, unregistering in vcenter (esx ver. 3.5, i call it esx3), register in vSphere (esx ver. 4, i call it esx4), and migrate upgrade virtual hardware before powering it up (First mistake). vMotion was enabled on esx4, seem to be a second mistake. After a day or so, i encountred problems joigning the esx server (esx4) and decided to unregister my server for esx4 and fallback to esx3. esx3 refused to boot, i supposed this was due to virtual hardware in Version 7 so i recreated a new VM pointing to the vmdk of the old VM. Everithing seemed fine until i log into the server and discover that i was running on the original disk ith every snapshots ignored even those created on esx3. I tried to reboot VM on esx4 but VM doesn't power up because "The parent virtual disk has been modified since the child was created". I've got a copy of a later state of the drive but generated between two snapshots (ovf generated with canverter standalone) as a backup. Do i have a chance to recover at least some files on the virtual drive or (as i tink) all is played, i've done enought mistakes for this time. Thanks for your help.

    Read the article

  • permanent NAS-mount in Ubuntu - wrong fs type, bad option, bad superblock

    - by Emil
    My network drive shows up in the file browser, just like my external usb-harddrive. Moving, running and editing files works. Hovering over it shows smb://lacie-2big/nasdisk . BUT, when I want to save a file, the drive doesn't come up as an option. All I can see is my other places, including my usb-harddrive. I am a complete newbie but I am GUESSING that it has something to do with the mount not being a "real" mount but just a shortcut to the smb location. So I ran the tutorial at https://wiki.ubuntu.com/MountWindowsSharesPermanently about how to "mount a network drive permanently". edited my fstab to //LaCie-2big/nasdisk /media/nasmount cifs guest,uid=1000,iocharset=utf8,codepage=unicode,unicode 0 0 and running sudo mount -a gave me the following error: mount: wrong fs type, bad option, bad superblock on //LaCie-2big/nasdisk, missing codepage or helper program, or other error (for several filesystems (e.g. nfs, cifs) you might need a /sbin/mount. helper program) In some cases useful info is found in syslog - try dmesg | tail or so Now thats a very helpful error message, BUT, before I go any further, I'd be really thankful if one of you could tell me if I'm even in the right ballpark, or if my actual need: to be able to download files (ie torrents) directly to the drive, can be possible as it is already. Question: How to fix "wrong fs type, bad option, bad superblock on //LaCie-2big/nasdisk, missing codepage or helper program" when running mount -a

    Read the article

  • Why does the screen resolution of 1440x900 suddenly disappear from Intel GMA Control Panel?

    - by GeneQ
    I'm using a Vostro 1200 laptop with the Mobile Intel(R) 965 Express Chipset powering its graphics and running Vista 32-bit SP2. I've been using the Vostro with a Dell SE198WFP LCD Monitor as the external display since day one for about two years without any problems. Recently, I plugged the Vostro into a couple of other monitors. The problem is, now the native resolution for my main monitor's (the SE198WFP) resolution of 1440x900 @ 60 Hz is no longer available. (See below) I've tried everything from uninstalling and reinstalling the Intel drivers as well as the monitor drivers to no avail. I've goggled this problem and it appears that this has happened to other people but all the answers involve people giving up in frustration or reinstalling; both terrible outcomes. Has anybody ever figured why this happens and have a good solution? UPDATE: This dude has a complicated solution, which I haven't tried yet. His explanations for the problem was After an exausting search for an answer to the matter of why my brand new 19? widescreen monitor’s native resolution (1440×900) was unavailible (sic) in the display properties, I finally stumbled upon an article a person posted on Intel’s forums that basically explained what shannanigans Intel had been up to with their GMA 950 line of onboard graphic solutions. Not very comforting.

    Read the article

  • Regular Windows 7 BSOD with Shrew VPN client

    - by Junto
    The Shrew VPN client appears to be a good alternative to the Cisco VPN Client on x64 Windows 7. However, since installing it I've seen fairly regular BSODs. Minidump attached: Microsoft (R) Windows Debugger Version 6.11.0001.404 AMD64 Copyright (c) Microsoft Corporation. All rights reserved. Loading Dump File [D:\Temp\020810-23431-01.dmp] Mini Kernel Dump File: Only registers and stack trace are available Symbol search path is: SRV*d:\symbols*http://msdl.microsoft.com/download/symbols Executable search path is: Windows 7 Kernel Version 7600 MP (8 procs) Free x64 Product: WinNt, suite: TerminalServer SingleUserTS Built by: 7600.16385.amd64fre.win7_rtm.090713-1255 Machine Name: Kernel base = 0xfffff800`0285f000 PsLoadedModuleList = 0xfffff800`02a9ce50 Debug session time: Mon Feb 8 18:08:12.887 2010 (GMT+1) System Uptime: 0 days 7:52:06.120 Loading Kernel Symbols ............................................................... ................................................................ .............. Loading User Symbols Loading unloaded module list .... ******************************************************************************* * * * Bugcheck Analysis * * * ******************************************************************************* Use !analyze -v to get detailed debugging information. BugCheck A, {0, 2, 0, fffff800028d50b6} Unable to load image \SystemRoot\system32\DRIVERS\vfilter.sys, Win32 error 0n2 *** WARNING: Unable to verify timestamp for vfilter.sys *** ERROR: Module load completed but symbols could not be loaded for vfilter.sys Probably caused by : vfilter.sys ( vfilter+29a6 ) Followup: MachineOwner Machine is a brand spanking new Dell Precision T5500. Superuser appears to have several recommendations for the Shrew VPN Client as an alternative to the Cisco VPN client on 64 bit machines, so I wondered if anyone here has seen this problem and possibly found a solution to the problem? I've decided to run the VPN client under Windows 7 compatibility mode for the moment (Vista SP2) with administrator privileges to see if it makes a difference. Oddly, the VPN doesn't necessarily need to be connected. I've noticed it when browsing using Google Chrome and Internet Explorer, usually when I open up a new tab. If it carries on I think I'll be forced to shell out the 120 EUR for the NCP Client instead.

    Read the article

  • PC powers off at random times

    - by Timo Huovinen
    Short Version After experiencing some problems with Mobo batteries my PC started to power off at random times, the power off is instant and sudden and does not restart afterwards, need help figuring out the cause. Facts: Powers off when PC is playing games Powers off when PC is idle Powers off when PC is in safe mode Powers off when PC is in BIOS Powers off when PC is booted through a Windows installation USB Replaced the motherboard battery several times Replaced the 650W PSU with a 750W PSU Replaced the RAM Swapped the RAM between slots Re-applied thermal paste to the CPU Checked if the motherboard touches the case Nothing is overclocked PC Specs PC specs: OS: Windows 7 Ultimate SP1 RAM: klingston 1333MHz 4GB stick CPU: AMD Phenom II x4 955 Mobo: Gigabyte 88GMA-UD2H rev 2.2 Motherboard battery: CR2032 3v HDD: 500GB Seagate ST3500418AS ATA Device Graphics: ATI/AMD Radeon HD 6870 Very Long version Around 10 months ago I built a brand new gaming PC. Around 6 months ago it's time setting in windows started resetting to the year 2010. I swapped the Motherboard battery for a new one of the exact same size and shape and voltage, and the problems disappeared...for around 2 weeks. Then the same problem happened again, time gets reset, I swapped the battery again, and the problem was gone for good and everything was great for about 3 months.. then another problem started happening, the PC started to power off suddenly and without warning at completely random times, sometimes the PC works for and hour, sometimes 5 minutes. So I read on the forums that it might be either the PSU or the motherboard Battery or RAM or HDD or the Graphics card or the CPU or the motherboard or the drivers or a Virus or Grounding issues, or something short circuiting, basically it can be anything... I spent some days researching, and decided to remove the possibility of a virus. I reset the CMOS, cleared all BIOS settings and reinstalled windows 7 after a full format of the HDD, but the random power off kept happening. I then disabled the restart on error option in windows and looked at the event log for error events, but they did not help me figure out the problem. Network list service depends on network location awareness the dependency group failed to start Source Kernel Power Event 41 Task Category 63 Source Disk Event ID 11 Task Category None The driver detected a controller error on device disk I took apart the PC, every little piece, re-applied some expensive thermal paste to the CPU, and double checked that none of the pieces are touching the PC case. The problem was gone, the PC no longer powered off randomly I re-attached the graphics card and all was good for 4 months... then the power off problem appeared again, but was happening at high intervals, the PC would shutdown once in 2 days on average, at random points in time, sometimes when it's idle all day long, sometimes when it's running CRYSIS 2. I checked the CPU temperature, because I know that AMD CPU's have a built in protection mechanism that switches off the PC if the CPU gets too hot, and the Temp was 50C system temp, and 45C CPU after running the PC all day long (I did not do tests to see if there are any temperature spikes, don't know how to do them) Originally the PSU that powered the PC was 650Watts and had one 4 pin cable to power the CPU, I replaced it with a new 750Watts PSU which has two 4 pin cables for the CPU, but the problem remained. I removed the graphics card and let the motherboard use the built in one, but the PC kept suddenly powering off at random times. I took apart the PC completely again, and re-applied thermal paste to the CPU, added lots of insulation, and checked for any type of short-circuit possibility again and again, but the problem remained. The problem was like that for some months. I replaced the Battery a couple of times over the time, changed lots of options in windows, and tried everything I could, but it kept powering off, so I stopped using the PC as much as I used to, just living with the random power offs from time to time, until a couple of days ago, when the power off happens almost immediately after powering on the PC. I replaced the RAM with a brand new one, but that did not help. Took apart the PC again, checked for anything anywhere that might cause it, found some small scratches on the very edge of the motherboard to the left of the PCI express x16 slot. This might cause the problem, I thought, but the scratch looks very superficial, not deep at all, and if the scratch did harm the motherboard, wouldn't it cause it to not start at all? And why did it start to power off a while ago, and then suddenly stop powering off? The scratches could not have vanished??? did chkdsk \d but it powered off when it was at 75% I removed the hard disks, the graphics card, while I fiddled with the BIOS settings, and suddenly the PC shut down while I was looking at the BIOS version. This makes me realize, it is not caused by: HDD, Windows, Drivers or the Graphics card I cleared the CMOS again, updated the BIOS from F5 to F6f beta, but that did not help, it might even seem that the PC powers off even sooner. The shutdown even happened to me while I booted through a windows 7 installation USB and was in the repair console. I removed one of the cables powering the CPU, now only one 4pin cable powers it, and it worked for 30mins after doing that, which makes me think that it's the CPU overheating, and because it gets less power, it overheats slower? The things that I am still considering: CPU overheating (does not seem to overheat, maybe false readings?) Motherboard short circuiting (faulty motherboard?) I desperately need some advice in what is faulty, is it a faulty Motherboard or an overheating CPU? or maybe something else? I have been breaking my head over this problem over a span of 6 months. I'm not sure if this is a good place to ask this question, if it is not, then tell me where I can get some experienced help. More info I have also discovered a mysterious piece that seems to have fallen out of the motherboard i119.photobucket.com/albums/o126/yurikolovsky/strangepiece.jpg What is it? Looks like each time that it powers off the datetime gets reset I also found another forum post tomshardware.co.uk/forum/… except I don't have Integrated PeripheralsUSB Keyboard Function option in BIOS :S Comments summary (asked by Random moderator) Q. tell me, if the computer restarts, is it immediately? Does it take a second and then restarts? Do you see (BSOD) or hear (PSU, short circuit) any suspicious when it happens? After reading trough it, it remains the mainboard that is faulty. – JohannesM A. Immediate power off, all the fans stop instantly, all the light turn off instantly, no sound or anything, and it remains off until I turn it back on. Thanks for the feedback, faulty motherboard is what I fear. Q. Try stress-testing the system with Prime95 and see if errors or shutdowns occur when the CPU is under full load. – speakr A. Prime95 heat stress test peaked CPU heat at 60C after 5mins, it powered off after 30mins of testing in the middle of the test with no errors, Prime95 Heat test or the stress-testing with low RAM usage (small or in-place FFTs) do not report errors while testing for 10-60 mins. The power off does not seem like it is affected by Prime95 at all Makes me wonder if it's a CPU or Motherboard issue at all. Q. I had similar random/intermittent problems with my old board. It gave one of a few different symptoms: keyboard and/or mouse would die and/or the RAM wouldn't work and/or it would shut down. It was in bad shape. One problems was that my old PSU had literally burned the connector on it (browned around the pins), another was that a broken lead inside the layers of the PCB would work sometimes if it happened to be hot or if I bent the board—by jamming a hunk of wood behind it. I managed to keep the board alive for several years, but eventually nothing I did would make it work correctly anymore. – Synetech A. I will try that as the last resort, ok? ;) Q. Have you tried a different power cord, surge protector, outlet (on a different circuit). It's worth a shot just to ensure it's not subpar wiring or a week circuit (dips in power may cause shutdown if the PSU can't pull enough juice from the wall). – Kyle A. yes, I attached the PC to an entirely different outlet on a different circuit and the problem persists. After connecting it to a different outlet after starting the PC it gave me 3 long beeps and 1 short one, then the PC immediately proceeded to boot up normally. Q. Re-check your mainboard manual and all PSU connections to your mainboard to be sure that nothing is missing (e.g. 12V ATX 4-pin/6-pin connector). If you can provoke shutdowns with Prime95, then consider buying new hardware -- a stable system should run Prime95 for 24h without any errors. Prime95 mentions errors in the log when they occur and gives a summary after the stress test was stopped manually (e.g. "0 errors, 0 warnings", if all is fine) – speakr A. Re-checked, there are no more PSU connectors that I can physically connect, except the one ATX 4-pin (there are 2 that power the CPU) that I disconnected on purpose, I have reconnected it but the problem persists. Q. With one PC I had a short curcuit. The power button on the front plate had its cables soldered, but not isolated, and the contacts were very close to the metal case. A heavier touch was enough to cause a shutdown. The PC's vibration could be enough – ott-- A. yes, it seems to switch off with even the lightest touch, I switched on the PC, then pulled out the front panel power cable that connects to the motherboard so the power button does not work anymore, after 5 mins of working like that, with the power button completely disconnected, just sitting idle, the PC powered off again, I don't think it's the power button. Q. I wonder if you dare to operate components without the case, that is remove motherboard, power, disk ( just put the motherboard on a wooden desk). Don't bend the adapters when running like that. – ott-- A. yes, I do dare to do that, but only tomorrow, too tired/late right now.

    Read the article

  • Apache virtualhost - only apply script if file does not exist in document root

    - by Brett Thomas
    Sorry for the newbie apache question. I'm wondering if it's possible to set up the following non-conventional apache virtualhost (for a Django app): -- If a file exists in the DocumentRoot (/var/www) it will be shown. So if /var/www/foo.html exists, then it can be seen at www.example.com/foo.html. -- If file does not exist, it is served via a virtualhost. I'm using mod_wsgi with a WSGIScriptAlias directive that points to a Django app. So if there is no /var/www/bar.html, www.example.com/bar.html will be passed to the Django app, which may or may not be a 404 error. One option is to create an Alias for each individual file/directory, but people want to be able to post a file without adding an alias, and we want to keep the above URL structure for legacy reasons. Simplified Virtualhost is: <VirtualHost *:80> ServerName www.example.com DocumentRoot /var/www WSGIScriptAlias / /path/to/django.wsgi <Directory /path/to/app> Order allow,deny Allow from all </Directory> Alias /hi.html /var/www/hi.html </VirtualHost> The goal is to have www.example.com/hi.html work as above, without the Alias line

    Read the article

  • FTP Server on Centos 5.8 - Transfer fails randomly

    - by Diego
    Hi have ProFTPD runningon a brand new CentOS 5.8 server with Plesk, and its behaviour is inconsistent at best. I tried to transfer a directory from my PC, and every time I get a transfer failed on a random file. It's never the same one that fails, it just fails. Sometimes it's a .gif, sometimes it's a .css, sometimes it's a JPG. Of several hundred files, a dozen is always failing for no apparent reason. The error that I get is the following: COMMAND:> [27/11/2012 11:43:52] STOR main_border.gif [27/11/2012 11:43:53] 500 Invalid command: try being more creative ERROR:> [27/11/2012 11:43:53] Syntax error: command unrecognized. The above is just an example, the "command unrecognized" occurs with LIST and other commands as well. Here's the ProFTPD configuration, just in case: ServerName "ProFTPD" #ServerType standalone ServerType inetd DefaultServer on <Global> DefaultRoot ~ psacln AllowOverwrite on </Global> DefaultTransferMode binary UseFtpUsers on TimesGMT off SetEnv TZ :/etc/localtime Port 21 Umask 022 MaxInstances 30 ScoreboardFile /var/run/proftpd/scoreboard TransferLog /usr/local/psa/var/log/xferlog #Change default group for new files and directories in vhosts dir to psacln <Directory /var/www/vhosts> GroupOwner psacln </Directory> # Enable PAM authentication AuthPAM on AuthPAMConfig proftpd IdentLookups off UseReverseDNS off AuthGroupFile /etc/group Include /etc/proftpd.include Note: file /etc/proftpd.include is blank. The above is the default configuration set by Plesk 11. I don't know much of why is that way, my knowledge of Linux System Administration is very basic and the one of ProFTPD is a complete zero. Thanks in advance for the help. Update Issue experienced with CuteFTP and FileZilla. Update Replaced ProFTPd with PureFTPd, issue persists. Sometimes I get "command unrecognized", sometimes "failed to establish data connection". I'm starting to think that it could be a network issue, but I have completely zero knowledge of networking.

    Read the article

  • Why won't this script accept any arguments?

    - by Nate Wagar
    I'm trying to write an SVN post-commit hook and, strangely, am getting hung up on what should be the easiest part. The Script: set REPO="$1" set REV="$2" set SVNBIN="/opt/CollabNet_Subversion/bin/" set SSHBIN="/usr/bin/ssh" set HOST="staging.domain.net" set timeout=30 set USERNAME="svn-usr" set E_NO_CONNECT=2 set E_WRONG_PASS=3 set E_UNKOWN=25 set CHANGED=`"$SVNBIN"svnlook changed --revision $REV $REPOS` echo "Here are changes: $CHANGED" >> /var/svn/repos/www/logs/testing echo "Command: $0; Repo: $REPO; Rev: $REV; Total: $#" >> /var/svn/repos/www/logs/testing set PROJECT "" Yet when I call it, it doesn't seem to be seeing the arguments I pass to it: /var/svn/repos/www/logs> sudo ../hooks/post-commit /var/svn/repos/www 33 svnlook: missing argument: --revision Type 'svnlook help' for usage. /var/svn/repos/www/logs> cat testing Here are changes: Command: ../hooks/post-commit; Repo: ; Rev: ; Total: 1 This is on a Solaris 10 SPARC box. I'm a bit of a script newbie, but shouldn't this be really easy??

    Read the article

  • Cannot find FIS partition 'initramfs'......... need help!!!

    - by vikramtheone
    Hi Guys, I have a Ubuntu 9.04 Linux running on Freescale's i.MX515(ARM Cortex based) board with me. There were about 250 updates pending and I did that today, well some of the updates failed because of the infamous errors: E: dpkg was interrupted, you must manually run 'sudo dpkg --configure -a' to correct the problem. E: Couldn't rebuild package cache E: dpkg was interrupted, you must manually run 'sudo dpkg --configure -a' to correct the problem. So, when I do the 'sudo dpkg --configure -a' I get new errors related to FIS partition: Cannot find FIS partition 'initramfs' User postinst hook script [/usr/sbin/flash-kernel] exited with value 1 dpkg: error processing linux-image-2.6.28-18-imx51 (--configure): subprocess post-installation script returned error exit status 1 dpkg: dependency problems prevent configuration of linux-image-imx51: linux-image-imx51 depends on linux-image-2.6.28-18-imx51; however: Package linux-image-2.6.28-18-imx51 is not configured yet. dpkg: error processing linux-image-imx51 (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of linux-imx51: linux-imx51 depends on linux-image-imx51 (= 2.6.28.18.23); however: Package linux-image-imx51 is not configured yet. dpkg: error processing linux-imx51 (--configure): dependency problems - leaving unconfigured Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-2.6.28-18-imx51 Cannot find FIS partition 'initramfs' dpkg: subprocess post-installation script returned error exit status 1 Whats going wrong here, need help!!! I'm a newbie. Regards Vikram

    Read the article

  • Cannot increase Datastore

    - by k4w4zz
    Hello, We have an ESX 4.0 cluster with 2 hosts, EMC Clarion SAN storage with 10 LUNs. We have added 2 new 400 GB LUNs. All the LUNs are visible from both hosts. I have extended an existing 500 GB datastore with one of these 400 GB LUNs - the new datastore size is now 900 GB. I'd like to do the same operation with the second 400 GB LUN to extend another existing datastore but I'm not able to do it. The LUN is available to create a brand new datastore but is not visible to extend an existing one. I don't understand why everything was fine with the other one and why can't I do the same exact operation with this LUN. The result is the same on both hosts. The SAN admin have erased and re-created several times this LUN. I have rescan the HBA each time. In attachment you can find the result of the esxcfg-mpath -l and fdisk -l commands on both servers. Does somebody have an idea please?

    Read the article

  • 13" MacBook Pro with Win 7 and External VGA gets 640x480

    - by Jim McKeeth
    I have a brand new 13" MacBook Pro - 2.26 GHz and the NVIDIA 9400M Video card. I installed Windows 7 (final) in boot camp and booted up to Windows 7. Installed all the drivers from the Apple disk and it was working great. Then I attached the external VGA adapter (from apple) to connect to a projector and it dropped down at 640x480 resolution. No matter what I did it wouldn't let me change to a higher resolution if the external VGA was connected. Once it disconnects then it goes back to the normal resolution. If I am booted into Snow Leopard it works fine. I tried updating the NVIDIA drivers and it behaved exactly the same. Ultimately I want to get 1024x768 or better resolution when connected to an external display. If it isn't fixable then I am curious if anyone else has seen this, if it is a known issue, and who to contact for support (Apple, Microsoft or NVIDIA?) Update: Just attaching the Mini-DVI to VGA adapter kicks it into 640x480, no projector is required. I tried forcing the display driver from Generic PnP Monitor to one that supported 1024x768 and that didn't work either.

    Read the article

  • How to send mail with PHP [migrated]

    - by roth66
    My litle problem is about mail() function in PHP, it doesnt want to send emails, to my local server, or anywhere else. I don't think that function was supposed to send mail to adresses like: [email protected]; So I've installed a mail server: hmailserver, I installed a client: dream-mail; I installed sendmaill.exe; (actually unzipped it in a folder, then in php.ini set the sendmail_path to point to it) After countless trials and errors, it still doesn't work. my system would comprise in an Apache server 2.2, and PHP (last version I think 5.3 or somehing), running on windows. And now for avoiding the usual questions (Did you make rules in your firewall etc etc), I guess I should mention, that there arent any connectivity issues, everything is set to "local" (localhost), port 25, 110, 143, are all opened, And, after a few days of fiddling with my brand new mail-server, I manage to make it work. THe Dream-mail client, has a test, trough which it would test its connections, and according to it, the SMTP AND POP3 connections are all successful, it even sends an email, for testing. SO ya, it would work. The problem, remains: PHP mail funcion. And I really need it, since on my website there's a contact form, and right now is useless. I've also checked the form it self, and seems to be alright.

    Read the article

  • Single computer on network cannot connect to internet.

    - by user34630
    Hi All, I hope you can help me out! :) I have 3 computers and one device (Xbox) on my home network; 2 running XP and one on Vista. The computer that can't connect to the internet (XP) is old and failing, and shows no warning before it completely runs out of battery. Thus today, I started it up forgetting that I had unplugged it the night before, and it just ran out of battery entirely whilst I was using it and died. I think that before this I had been browsing the internet, but I can't remember for certain. (i.e. The problem I am having may or may not have been caused by this 'hard' power off). Anyway, now when I start the computer up it takes 5-10 minutes after logging on to display the start bar and icons. Also, I cannot browse the internet. The computer seems to connect to the network OK (I have tried both wired and wireless), but I can't visit sites and can't ping web addresses. Pinging the router fails, as does pinging another of my computers on the network. I have never encountered something like this before, and whilst I am no noob I am also not a sysadmin, haha. :( Any help is greatly appreciated, thank you for your time. P.S. I have tried a system restore (newbie move?).

    Read the article

  • How to move my data from my old MacBook Pro to my new one?

    - by Tim Büthe
    I just purchased a new MacBook Pro and already got an 2008 model. I wonder how I move all my data over to the new one. My first idea was, to use my Time Machine backup and restore from it, which seems to be a good idea and should work just fine regarding to this link: http://blog.duncandavidson.com/2008/01/restoring-from-time-machine.html. But, since my current MacBook got older Software on it, like iLife '08 instead of iLife '09 I would have to upgrade this afterwards. Is this correct, or does Time Machine does some magic to exclude well known software? And is it possible to reinstall or upgrade iLife with the included installation DVDs? My second idea is, to just swap the hard drives instead of using the Time machine backup. If it is not too complicated to remove the hdd, this should be the fastest way. This also has the benefit, that the 2008er MacBook then contains a brand new installation and I don't have to remove all my stuff or reinstall Mac OS before I give it away. My question on that second idea would be: does snow leopard handle this stuff correctly? I reboot with the new hardware and all just works fine? So in a nutshell: What would you do: restore from backup or swap drives? And what about the new software?

    Read the article

  • Constant crashes in windows 7 64bit when playing games

    - by yx
    I've tried everything I can possibly think of in trying to fix this problem and I'm totally out of ideas, so any help would be appreciated: The problem: whenever I fire up a game, it works for a short while with no problems and then it would crash. Either its a hard crash, forcing me to reboot, or windows would report that the display driver has stopped working and recovered. Here is a list of things I've already tried: Drivers - tried the latest drivers (catalyst 9.12) as well as the stock drivers that came with the video card. Also have the latest BIOS/chipset Memtest - Ran Memtest86+ overnight, had no problems, the windows diagnostic tool also does not find any problems. Overheating - Video card/cpu temperatures are well below peak (42 and 31 Celsius receptively) PSU Voltage - CPUID shows that the voltage levels are all above what they should be. The PSU itself is only roughly 16 months old and is a good model. HDD - No errors when checked GPU - Brand new (replaced previous card since I thought it was the problem, apparently not) Overclocking - Everything is at stock levels, memory voltage is set to manufacturer's standard Specs: Motherboard: ASUS P5Q Pro CPU: Core 2 Duo E8400 3.0 ghz OS: Windows 7 home premium 64 bit Memory: Mushkin Enhanced 4GB DDR2 GPU: Sapphire HD 5850 1GB PSU: SeaSonic M12 600W ATX12V DirectX: DX11 Event Viewer after a crash always has these logged: A fatal hardware error has occurred. Reported by component: Processor Core Error Source: Machine Check Exception Error Type: Bus/Interconnect Error Processor ID: 1 The details view of this entry contains further information. A fatal hardware error has occurred. Reported by component: Processor Core Error Source: Machine Check Exception Error Type: Bus/Interconnect Error Processor ID: 0 The details view of this entry contains further information. A previous card that I had (4850x2) also had these errors, so I changed video cards, but the same thing is happening.

    Read the article

  • Computer resetting semi-randomly

    - by Peter
    Hi, I'm having a problem with my desktop whereby it sometimes resets itself semi-randomly. For example, I'll switch it on, it'll boot an OS and shortly after getting to the desktop it will immediately reset with no warning. The time isn't consistent - sometimes it does it before reaching login. I'm pretty sure it's not an OS thing; have tried Ubuntu and a Windows install and both exhibit it. It also doesn't appear to be heat-related because sometimes it appears to be able to "get past" it and will then run stably even under load; if anything it seems to be worse from a cold start. My gut feeling is some kind of power issue but I'm clutching at straws a little. Any suggestions on how I could go about testing it or trying to narrow the problem down would be appreciated. The machine is four years old now so while I can replace components if needed, it's not worth enough that I'm comfortable buying new parts without being pretty confident that they'll fix the problem. Thanks in advance for any help :) Edit: Okay, the motherboard is a MSI K8N SLI; CPU is an Athlon64 X2 4200+. Has one video card, a GeForce 7800GT. 1GB RAM, not sure of brand; 3 hard drives, two SATA and one PATA. Flashed motherboard to latest BIOS some time ago. Edit the Second: I thought I'd narrowed it down to the PSU for a while, but then it recurred again. I ended up pulling everything out but CPU, RAM and motherboard and it still seems to be stuffed (if anything, it's gotten worse in the last couple of days). I assume it's one of those three components, but the machine is old enough that I don't really want to spend money replacing any of them. So thanks for everyone's suggestions; much appreciated!

    Read the article

< Previous Page | 115 116 117 118 119 120 121 122 123 124 125 126  | Next Page >