Search Results

Search found 1667 results on 67 pages for 'dhcp'.

Page 12/67 | < Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >

  • How to share internet connection and making the client accessible over the lan

    - by Dario Silva Moran
    I've a Pc with Ubuntu 14.04 connected to a linkys router through wlan0, and I'd like to share internet connection to an AVR with ethernet port. This is pretty simple if only internet connection is required for the AVR: actually, creating an ethernet connection as "Shared with other computers" and setting up the AVR IP configuration to use DHCP works just fine, but that makes a private class A lan between those two; of course ip addresses are not in the range of the LAN the router is managing. So, I tried with static ip on both sides (Ubuntu eth0 and AVR ip). Tried many combinations, none of them work to provide Internet access to the AVR and at the same time make the AVR accessible over the network through his static ip address (say, 192.168.0.110). Any tips around to share??

    Read the article

  • CUPS: HP printer DNS url

    - by wintersolutions
    The URL for my printer generated by hp-makeuri looks like this: hp:/net/Officejet_6500_E710n-z?ip=192.168.178.30 But the printer is on a dhcp enabled wifi network and so its IP-address does and could change. On the other hand my wifi router seems smart enough to have some sort of DNS: $ ping hp-6500a PING hp-6500a.fritz.box (192.168.178.30) 56(84) bytes of data. 64 bytes from hp-6500a.fritz.box (192.168.178.30): icmp_req=1 ttl=255 time=11.3 ms I tried to use the hostname in the CUPS URL/DeviceUID but it failed, any suggestions if this is possible and the correct format?

    Read the article

  • Unable to set default gateway

    - by GrandMasterFlush
    I'm running Ubuntu server via Hyper-V and have successfully installed it but seem unable to ping the server or ping any other machines on the network from the server. After doing a bit of reading I've noticed that the default gateway isn't set but when I try and set it I keep getting error messages which I can't understand. From this article I've tried ip route add default via 10.0.10.200 Which reports: RTNETLINK answers: Operation not permitted If I try running it prefixed with sudo but it reports: `RNETLINK answers: No such process I've editted /etc/network/interfaces but when I start the machine and type netstat -nr there is nothing listed. Can anyone tell me where I'm going wrong please? EDIT : /etc/network/interfaces contains: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp

    Read the article

  • How to make an internet server as firewall using ubuntu 11.10

    - by Sumant
    i have one static broadband connection which is coming to my Ubuntu server with 2 lan cards, there are 10 more PC's to which i need to provide internet connection through Ubuntu server as well as i have to block social networking websites access during office hours. Now i am getting confuse with the way i should follow i should go for sharing internet connection & firewall building or should configure DHCP server,router & firewall. which will be easiest setup and what i should do for that. coz its first time i will be doing.

    Read the article

  • Defaulting internet requests to wlan0 when also connected to eth0

    - by Dudemcman
    I am trying to configure an Ubuntu 10.04 desktop edition as a server. I currently have the DHCP server working through eth0. My problem is that I only have one Ethernet port, and am receiving Internet though a mobile hotspot on my phone through wlan0, and whenever I attempt to connect through wlan0 and eth0 I am unable to access the Internet through the server or the clients. When I disconnect from eth0 I then regain access. I have searched extensively for a solution, and have come up short. Any help is appreciated.

    Read the article

  • SSH via DHCP server

    - by SFault
    I have a DHCP server setup and I can't seem to connect to anything through SSH. When I'm logged in to the server itself, I can SSH. But when I connect any machine to the DHCP server, that machine can SSH but every server I SSH to asks for a password when the normal behavior (when not connected to the DHCP server) does not. Here are the contents of my iptables script that are related to port 22. $IPT -t nat -A PREROUTING -i $LAN -p tcp --dport 22 -j REDIRECT --to-port 22 $IPT -A FORWARD -i $LAN -p tcp --dport 22 -j ACCEPT $IPT -A INPUT -i $LAN -p tcp --dport 22 -j ACCEPT $IPT -A INPUT -i $WAN -p tcp --dport 22 -j ACCEPT $IPT -A OUTPUT -p tcp --sport 22 -m state --state ESTABLISHED -j ACCEPT $IPT -A INPUT -i $LAN -p tcp --dport 22 -m state --state NEW,ESTABLISHED -j ACCEPT Am I missing something?

    Read the article

  • dhcrelay running as both DHCP and DHCPv6 relay agent on CentOS 6.2

    - by Tibor
    I am trying to set up a DHCP relay agent that would relay DHCP requests for both IPv4 and IPv6. I am using CentOS 6.2 and I am using the dhcrelay from the ISC DHCP implementation. I would like to set it up as a service, but the man page for dhcrelay states: -6 Run dhcrelay as a DHCPv6 relay agent. Incompatible with the -4 option. -4 Run dhcrelay as a DHCPv4/BOOTP relay agent. This is the default mode of operation, so the argu- ment is not necessary, but may be specified for clarity. Incompatible with -6. It seems that the -6 and -4 options are incompatible. How would I still make it work for both protocols without rolling my own service wrapper for both cases?

    Read the article

  • Have to run sudo dhclient eth0 automatically every boot

    - by Fyksen
    I just installed ubuntu 12.04.1 alternative install (for raid 0 on some disks). I Have some problems with the net. I'm at school, we use cable, and it got IPv6. If I run ifconfig eth0 heres my output: eth0 Link encap:Ethernet HWaddr e0:cb:4e:87:ff:db inet addr:128.39.194.217 Bcast:128.39.194.223 Mask:255.255.255.224 inet6 addr: 2001:700:1100:8008:e2cb:4eff:fe87:ffdb/64 Scope:Global inet6 addr: fe80::e2cb:4eff:fe87:ffdb/64 Scope:Link inet6 addr: 2001:700:1100:8008:48f7:c23:1d87:da6c/64 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1063378 errors:0 dropped:0 overruns:0 frame:0 TX packets:489811 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1577173461 (1.5 GB) TX bytes:37043669 (37.0 MB) Interrupt:68 Base address:0x6000 My /etc/network/interfaces look like this: # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 # NetworkManager#iface eth0 inet dhcp # NetworkManager#hostname 2001:700:1100:1::4 # This is an autoconfigured IPv6 interface iface eth0 inet6 auto (I had to remove the hash tags, because of the BIGFONT i get on ask ubuntu) The "network manager" says that I'm not connected. Let me know if you need any more information. :)

    Read the article

  • Ubuntu 12.04 VPN default route issue when using the UI

    - by Pieter Pabst
    When setting up a VPN connection using the UI (System settings = Network) the VPN connection is used as the default route after connecting to it. How can I avoid this? That is without assigning manual addresses. I want the connection to use DHCP. It should use the eth* interfaces for my default route, like they are used before making the connection. The VPN route should only be used when connecting to addresses in the ppp0 adapters range. If possible using the UI only, not that I'm not used to editing config files... But the point of using Ubuntu for me was the "it just works" concept (which is true for 99% of the time, keep up the good work). I tried setting the "Method" combobox in the "Configure..." dialogue to "Automatic (VPN) addresses only". That doesn't make a difference. (Another thing I noticed; the UI shows my connection as a "Wireless connection" in the list control on the left. Don't know why... it has the right icon, but that's probably something for the bug tracker)

    Read the article

  • Is it possible to run dhcpd3 as non-root user in a chroot jail?

    - by Lenain
    Hi everyone. I would like to run dhcpd3 from a chroot jail on Debian Lenny. At the moment, I can run it as root from my jail. Now I want to do this as non-root user (as "-u blah -t /path/to/jail" Bind option). If I start my process like this : start-stop-daemon --chroot /home/jails/dhcp --chuid dhcp \ --start --pidfile /home/jails/dhcp/var/run/dhcp.pid --exec /usr/sbin/dhcpd3 I get stuck with these errors : Internet Systems Consortium DHCP Server V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ unable to create icmp socket: Operation not permitted Wrote 0 deleted host decls to leases file. Wrote 0 new dynamic host decls to leases file. Wrote 0 leases to leases file. Open a socket for LPF: Operation not permitted strace : brk(0) = 0x911b000 fcntl64(0, F_GETFD) = 0 fcntl64(1, F_GETFD) = 0 fcntl64(2, F_GETFD) = 0 access("/etc/suid-debug", F_OK) = -1 ENOENT (No such file or directory) access("/etc/ld.so.nohwcap", F_OK) = -1 ENOENT (No such file or directory) mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xb775d000 access("/etc/ld.so.preload", R_OK) = -1 ENOENT (No such file or directory) open("/etc/ld.so.cache", O_RDONLY) = -1 ENOENT (No such file or directory) open("/lib/tls/i686/cmov/libc.so.6", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/lib/tls/i686/cmov", 0xbfc2ac84) = -1 ENOENT (No such file or directory) open("/lib/tls/i686/libc.so.6", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/lib/tls/i686", 0xbfc2ac84) = -1 ENOENT (No such file or directory) open("/lib/tls/cmov/libc.so.6", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/lib/tls/cmov", 0xbfc2ac84) = -1 ENOENT (No such file or directory) open("/lib/tls/libc.so.6", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/lib/tls", 0xbfc2ac84) = -1 ENOENT (No such file or directory) open("/lib/i686/cmov/libc.so.6", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/lib/i686/cmov", 0xbfc2ac84) = -1 ENOENT (No such file or directory) open("/lib/i686/libc.so.6", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/lib/i686", 0xbfc2ac84) = -1 ENOENT (No such file or directory) open("/lib/cmov/libc.so.6", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/lib/cmov", 0xbfc2ac84) = -1 ENOENT (No such file or directory) open("/lib/libc.so.6", O_RDONLY) = 3 read(3, "\177ELF\1\1\1\0\0\0\0\0\0\0\0\0\3\0\3\0\1\0\0\0\260e\1\0004\0\0\0t"..., 512) = 512 fstat64(3, {st_mode=S_IFREG|0755, st_size=1294572, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xb775c000 mmap2(NULL, 1300080, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_DENYWRITE, 3, 0) = 0xb761e000 mmap2(0xb7756000, 12288, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_DENYWRITE, 3, 0x138) = 0xb7756000 mmap2(0xb7759000, 9840, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0xb7759000 close(3) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xb761d000 set_thread_area({entry_number:-1 - 6, base_addr:0xb761d6b0, limit:1048575, seg_32bit:1, contents:0, read_exec_only:0, limit_in_pages:1, seg_not_present:0, useable:1}) = 0 mprotect(0xb7756000, 4096, PROT_READ) = 0 open("/dev/null", O_RDWR) = 3 close(3) = 0 brk(0) = 0x911b000 brk(0x913c000) = 0x913c000 socket(PF_FILE, SOCK_DGRAM, 0) = 3 fcntl64(3, F_SETFD, FD_CLOEXEC) = 0 connect(3, {sa_family=AF_FILE, path="/dev/log"...}, 110) = 0 time(NULL) = 1284760816 open("/etc/localtime", O_RDONLY) = 4 fstat64(4, {st_mode=S_IFREG|0644, st_size=2945, ...}) = 0 fstat64(4, {st_mode=S_IFREG|0644, st_size=2945, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xb761c000 read(4, "TZif2\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\f\0\0\0\f\0\0\0\0\0"..., 4096) = 2945 _llseek(4, -28, [2917], SEEK_CUR) = 0 read(4, "\nCET-1CEST,M3.5.0,M10.5.0/3\n"..., 4096) = 28 close(4) = 0 munmap(0xb761c000, 4096) = 0 stat64("/etc/localtime", {st_mode=S_IFREG|0644, st_size=2945, ...}) = 0 send(3, "Sep 18 00:00:16 dhcpd: Intern"..., 73, MSG_NOSIGNAL) = 73 write(2, "Internet Systems Consortium DHCP "..., 46Internet Systems Consortium DHCP Server V3.1.1) = 46 write(2, "\n"..., 1 ) = 1 time(NULL) = 1284760816 stat64("/etc/localtime", {st_mode=S_IFREG|0644, st_size=2945, ...}) = 0 send(3, "Sep 18 00:00:16 dhcpd: Copyri"..., 75, MSG_NOSIGNAL) = 75 write(2, "Copyright 2004-2008 Internet Syst"..., 48Copyright 2004-2008 Internet Systems Consortium.) = 48 write(2, "\n"..., 1 ) = 1 time(NULL) = 1284760816 stat64("/etc/localtime", {st_mode=S_IFREG|0644, st_size=2945, ...}) = 0 send(3, "Sep 18 00:00:16 dhcpd: All ri"..., 47, MSG_NOSIGNAL) = 47 write(2, "All rights reserved."..., 20All rights reserved.) = 20 write(2, "\n"..., 1 ) = 1 time(NULL) = 1284760816 stat64("/etc/localtime", {st_mode=S_IFREG|0644, st_size=2945, ...}) = 0 send(3, "Sep 18 00:00:16 dhcpd: For in"..., 77, MSG_NOSIGNAL) = 77 write(2, "For info, please visit http://www"..., 50For info, please visit http://www.isc.org/sw/dhcp/) = 50 write(2, "\n"..., 1 ) = 1 socket(PF_FILE, SOCK_STREAM, 0) = 4 fcntl64(4, F_SETFL, O_RDWR|O_NONBLOCK) = 0 connect(4, {sa_family=AF_FILE, path="/var/run/nscd/socket"...}, 110) = -1 ENOENT (No such file or directory) close(4) = 0 socket(PF_FILE, SOCK_STREAM, 0) = 4 fcntl64(4, F_SETFL, O_RDWR|O_NONBLOCK) = 0 connect(4, {sa_family=AF_FILE, path="/var/run/nscd/socket"...}, 110) = -1 ENOENT (No such file or directory) close(4) = 0 open("/etc/nsswitch.conf", O_RDONLY) = 4 fstat64(4, {st_mode=S_IFREG|0644, st_size=475, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xb761c000 read(4, "# /etc/nsswitch.conf\n#\n# Example "..., 4096) = 475 read(4, ""..., 4096) = 0 close(4) = 0 munmap(0xb761c000, 4096) = 0 open("/lib/libnss_db.so.2", O_RDONLY) = -1 ENOENT (No such file or directory) open("/usr/lib/tls/i686/cmov/libnss_db.so.2", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/usr/lib/tls/i686/cmov", 0xbfc2ad5c) = -1 ENOENT (No such file or directory) open("/usr/lib/tls/i686/libnss_db.so.2", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/usr/lib/tls/i686", 0xbfc2ad5c) = -1 ENOENT (No such file or directory) open("/usr/lib/tls/cmov/libnss_db.so.2", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/usr/lib/tls/cmov", 0xbfc2ad5c) = -1 ENOENT (No such file or directory) open("/usr/lib/tls/libnss_db.so.2", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/usr/lib/tls", 0xbfc2ad5c) = -1 ENOENT (No such file or directory) open("/usr/lib/i686/cmov/libnss_db.so.2", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/usr/lib/i686/cmov", 0xbfc2ad5c) = -1 ENOENT (No such file or directory) open("/usr/lib/i686/libnss_db.so.2", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/usr/lib/i686", 0xbfc2ad5c) = -1 ENOENT (No such file or directory) open("/usr/lib/cmov/libnss_db.so.2", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/usr/lib/cmov", 0xbfc2ad5c) = -1 ENOENT (No such file or directory) open("/usr/lib/libnss_db.so.2", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/usr/lib", 0xbfc2ad5c) = -1 ENOENT (No such file or directory) open("/lib/i486-linux-gnu/tls/i686/cmov/libnss_db.so.2", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/lib/i486-linux-gnu/tls/i686/cmov", 0xbfc2ad5c) = -1 ENOENT (No such file or directory) open("/lib/i486-linux-gnu/tls/i686/libnss_db.so.2", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/lib/i486-linux-gnu/tls/i686", 0xbfc2ad5c) = -1 ENOENT (No such file or directory) open("/lib/i486-linux-gnu/tls/cmov/libnss_db.so.2", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/lib/i486-linux-gnu/tls/cmov", 0xbfc2ad5c) = -1 ENOENT (No such file or directory) open("/lib/i486-linux-gnu/tls/libnss_db.so.2", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/lib/i486-linux-gnu/tls", 0xbfc2ad5c) = -1 ENOENT (No such file or directory) open("/lib/i486-linux-gnu/i686/cmov/libnss_db.so.2", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/lib/i486-linux-gnu/i686/cmov", 0xbfc2ad5c) = -1 ENOENT (No such file or directory) open("/lib/i486-linux-gnu/i686/libnss_db.so.2", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/lib/i486-linux-gnu/i686", 0xbfc2ad5c) = -1 ENOENT (No such file or directory) open("/lib/i486-linux-gnu/cmov/libnss_db.so.2", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/lib/i486-linux-gnu/cmov", 0xbfc2ad5c) = -1 ENOENT (No such file or directory) open("/lib/i486-linux-gnu/libnss_db.so.2", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/lib/i486-linux-gnu", 0xbfc2ad5c) = -1 ENOENT (No such file or directory) open("/usr/lib/i486-linux-gnu/tls/i686/cmov/libnss_db.so.2", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/usr/lib/i486-linux-gnu/tls/i686/cmov", 0xbfc2ad5c) = -1 ENOENT (No such file or directory) open("/usr/lib/i486-linux-gnu/tls/i686/libnss_db.so.2", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/usr/lib/i486-linux-gnu/tls/i686", 0xbfc2ad5c) = -1 ENOENT (No such file or directory) open("/usr/lib/i486-linux-gnu/tls/cmov/libnss_db.so.2", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/usr/lib/i486-linux-gnu/tls/cmov", 0xbfc2ad5c) = -1 ENOENT (No such file or directory) open("/usr/lib/i486-linux-gnu/tls/libnss_db.so.2", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/usr/lib/i486-linux-gnu/tls", 0xbfc2ad5c) = -1 ENOENT (No such file or directory) open("/usr/lib/i486-linux-gnu/i686/cmov/libnss_db.so.2", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/usr/lib/i486-linux-gnu/i686/cmov", 0xbfc2ad5c) = -1 ENOENT (No such file or directory) open("/usr/lib/i486-linux-gnu/i686/libnss_db.so.2", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/usr/lib/i486-linux-gnu/i686", 0xbfc2ad5c) = -1 ENOENT (No such file or directory) open("/usr/lib/i486-linux-gnu/cmov/libnss_db.so.2", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/usr/lib/i486-linux-gnu/cmov", 0xbfc2ad5c) = -1 ENOENT (No such file or directory) open("/usr/lib/i486-linux-gnu/libnss_db.so.2", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/usr/lib/i486-linux-gnu", 0xbfc2ad5c) = -1 ENOENT (No such file or directory) open("/lib/libnss_files.so.2", O_RDONLY) = 4 read(4, "\177ELF\1\1\1\0\0\0\0\0\0\0\0\0\3\0\3\0\1\0\0\0\320\30\0\0004\0\0\0\250"..., 512) = 512 fstat64(4, {st_mode=S_IFREG|0644, st_size=38408, ...}) = 0 mmap2(NULL, 41624, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_DENYWRITE, 4, 0) = 0xb7612000 mmap2(0xb761b000, 8192, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_DENYWRITE, 4, 0x8) = 0xb761b000 close(4) = 0 open("/etc/services", O_RDONLY|O_CLOEXEC) = 4 fcntl64(4, F_GETFD) = 0x1 (flags FD_CLOEXEC) fstat64(4, {st_mode=S_IFREG|0644, st_size=18480, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xb7611000 read(4, "# Network services, Internet styl"..., 4096) = 4096 read(4, "9/tcp\t\t\t\t# Quick Mail Transfer Pr"..., 4096) = 4096 read(4, "note\t1352/tcp\tlotusnotes\t# Lotus "..., 4096) = 4096 read(4, "tion\nafs3-kaserver\t7004/udp\nafs3-"..., 4096) = 4096 read(4, "backup\t2989/tcp\t\t\t# Afmbackup sys"..., 4096) = 2096 read(4, ""..., 4096) = 0 close(4) = 0 munmap(0xb7611000, 4096) = 0 time(NULL) = 1284760816 open("/etc/protocols", O_RDONLY|O_CLOEXEC) = 4 fstat64(4, {st_mode=S_IFREG|0644, st_size=2626, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xb7611000 read(4, "# Internet (IP) protocols\n#\n# Upd"..., 4096) = 2626 close(4) = 0 munmap(0xb7611000, 4096) = 0 socket(PF_INET, SOCK_RAW, IPPROTO_ICMP) = -1 EPERM (Operation not permitted) time(NULL) = 1284760816 stat64("/etc/localtime", {st_mode=S_IFREG|0644, st_size=2945, ...}) = 0 send(3, "Sep 18 00:00:16 dhcpd: unable"..., 80, MSG_NOSIGNAL) = 80 write(2, "unable to create icmp socket: Ope"..., 53unable to create icmp socket: Operation not permitted) = 53 write(2, "\n"..., 1 ) = 1 open("/etc/dhcp3/dhcpd.conf", O_RDONLY) = 4 lseek(4, 0, SEEK_END) = 1426 lseek(4, 0, SEEK_SET) = 0 read(4, "#----------------------------\n# G"..., 1426) = 1426 close(4) = 0 mmap2(NULL, 401408, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xb75b0000 mmap2(NULL, 401408, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xb754e000 mmap2(NULL, 401408, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xb74ec000 brk(0x916f000) = 0x916f000 close(3) = 0 socket(PF_FILE, SOCK_DGRAM, 0) = 3 fcntl64(3, F_SETFD, FD_CLOEXEC) = 0 connect(3, {sa_family=AF_FILE, path="/dev/log"...}, 110) = 0 time(NULL) = 1284760816 stat64("/etc/localtime", {st_mode=S_IFREG|0644, st_size=2945, ...}) = 0 send(3, "Sep 18 00:00:16 dhcpd: Inter"..., 74, MSG_NOSIGNAL) = 74 time(NULL) = 1284760816 stat64("/etc/localtime", {st_mode=S_IFREG|0644, st_size=2945, ...}) = 0 send(3, "Sep 18 00:00:16 dhcpd: Copyr"..., 76, MSG_NOSIGNAL) = 76 time(NULL) = 1284760816 stat64("/etc/localtime", {st_mode=S_IFREG|0644, st_size=2945, ...}) = 0 send(3, "Sep 18 00:00:16 dhcpd: All r"..., 48, MSG_NOSIGNAL) = 48 time(NULL) = 1284760816 stat64("/etc/localtime", {st_mode=S_IFREG|0644, st_size=2945, ...}) = 0 send(3, "Sep 18 00:00:16 dhcpd: For i"..., 78, MSG_NOSIGNAL) = 78 open("/var/lib/dhcp3/dhcpd.leases", O_RDONLY) = 4 lseek(4, 0, SEEK_END) = 126 lseek(4, 0, SEEK_SET) = 0 read(4, "# The format of this file is docu"..., 126) = 126 close(4) = 0 open("/var/lib/dhcp3/dhcpd.leases", O_WRONLY|O_CREAT|O_APPEND, 0666) = 4 fstat64(4, {st_mode=S_IFREG|0644, st_size=126, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xb74eb000 fstat64(4, {st_mode=S_IFREG|0644, st_size=126, ...}) = 0 _llseek(4, 126, [126], SEEK_SET) = 0 time(NULL) = 1284760816 time(NULL) = 1284760816 open("/var/lib/dhcp3/dhcpd.leases.1284760816", O_WRONLY|O_CREAT|O_TRUNC, 0664) = 5 fcntl64(5, F_GETFL) = 0x1 (flags O_WRONLY) fstat64(5, {st_mode=S_IFREG|0644, st_size=0, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xb74ea000 _llseek(5, 0, [0], SEEK_CUR) = 0 close(4) = 0 munmap(0xb74eb000, 4096) = 0 time(NULL) = 1284760816 stat64("/etc/localtime", {st_mode=S_IFREG|0644, st_size=2945, ...}) = 0 send(3, "Sep 18 00:00:16 dhcpd: Wrote"..., 70, MSG_NOSIGNAL) = 70 write(2, "Wrote 0 deleted host decls to lea"..., 42Wrote 0 deleted host decls to leases file.) = 42 write(2, "\n"..., 1 ) = 1 time(NULL) = 1284760816 stat64("/etc/localtime", {st_mode=S_IFREG|0644, st_size=2945, ...}) = 0 send(3, "Sep 18 00:00:16 dhcpd: Wrote"..., 74, MSG_NOSIGNAL) = 74 write(2, "Wrote 0 new dynamic host decls to"..., 46Wrote 0 new dynamic host decls to leases file.) = 46 write(2, "\n"..., 1 ) = 1 time(NULL) = 1284760816 stat64("/etc/localtime", {st_mode=S_IFREG|0644, st_size=2945, ...}) = 0 send(3, "Sep 18 00:00:16 dhcpd: Wrote"..., 58, MSG_NOSIGNAL) = 58 write(2, "Wrote 0 leases to leases file."..., 30Wrote 0 leases to leases file.) = 30 write(2, "\n"..., 1 ) = 1 write(5, "# The format of this file is docu"..., 126) = 126 fsync(5) = 0 unlink("/var/lib/dhcp3/dhcpd.leases~") = 0 link("/var/lib/dhcp3/dhcpd.leases", "/var/lib/dhcp3/dhcpd.leases~") = 0 rename("/var/lib/dhcp3/dhcpd.leases.1284760816", "/var/lib/dhcp3/dhcpd.leases") = 0 socket(PF_INET, SOCK_DGRAM, IPPROTO_UDP) = 4 ioctl(4, SIOCGIFCONF, {0 - 64, NULL}) = 0 ioctl(4, SIOCGIFCONF, {64, {{"lo", {AF_INET, inet_addr("127.0.0.1")}}, {"eth0", {AF_INET, inet_addr("192.168.0.10")}}}}) = 0 ioctl(4, SIOCGIFFLAGS, {ifr_name="lo", ifr_flags=IFF_UP|IFF_LOOPBACK|IFF_RUNNING}) = 0 ioctl(4, SIOCGIFFLAGS, {ifr_name="eth0", ifr_flags=IFF_UP|IFF_BROADCAST|IFF_RUNNING|IFF_MULTICAST}) = 0 ioctl(4, SIOCGIFHWADDR, {ifr_name="eth0", ifr_hwaddr=00:c0:26:87:55:c0}) = 0 socket(PF_PACKET, SOCK_PACKET, 768) = -1 EPERM (Operation not permitted) time(NULL) = 1284760816 stat64("/etc/localtime", {st_mode=S_IFREG|0644, st_size=2945, ...}) = 0 send(3, "Sep 18 00:00:16 dhcpd: Open "..., 74, MSG_NOSIGNAL) = 74 write(2, "Open a socket for LPF: Operation "..., 46Open a socket for LPF: Operation not permitted) = 46 write(2, "\n"..., 1 ) = 1 exit_group(1) = ? I understand that dhcpd wants to create sockets on port 67... but I don't know how to authorize that through the chroot. Any idea?

    Read the article

  • Dynamic DNS updates for Linux and Mac OS X machines with a Windows DNS server

    - by DanielGibbs
    My network has a Windows machine running Server 2008 R2 which provides DHCP and DNS. I'm not particularly familiar with Windows domains, but the domain is set to home.local and that is the DNS domain name provided with DHCP leases. Everything works fine for Windows machines, they get the lease and update the server with their hostname and the server creates a DNS records for windowshostname.home.local. I am having problems obtaining the same functionality on Linux (Debian) and Mac OS X (Mountain Lion) machines. They receive DHCP just fine, but DNS entries are not being created on the server for them. On the Mac OS X machine, hostname gives an output of machostname.local, and on the Linux machine hostname --fqdn also gives an output of linuxhostname.local. I'm assuming that the server is not creating DNS entries because the domain does not match that of the server (home.local). I don't want to statically configure these machines to be part of the home.local domain, I just want them to pick it up from DHCP and be able to have entries in the DNS server. How should I go about doing this?

    Read the article

  • Move sendmail from Fedora 1 to a different server ( fedora 12)

    - by tanieboy4u
    We have a sendmail server that also works as DHCP, DNS, and a gateway to our ISP. It has three network interfaces, one for our ISP ( static IP) and the other two is for LANS on different subnet. The hardware is quite old and we've been experiencing downtime due to hardware failures, so we have decided to upgrade the hardware and while at it upgrade the linux OS to Fedora 12. Were trying to do this with minimal downtime. We are planning to take these steps. Install New OS (Fedora 12) on the new server with 3 network interfaces. Install DHCP, BIND, Sendmail, SpamAssassin, MailScanner, Dovecot, Squirrelmail on the new server. Transfer settings from the old server to the new server. ( This is the hardest part that we know). For DHCP and DNS, we can just copy the dhcp leases and conf file and everything should work right? How do we go about moving the users/email accounts from the old server to the new one? Thanks for all your help!

    Read the article

  • MAC addresses on dual-NIC mainboards

    - by Tom O'Connor
    Here's a weird problem. We've got a number of devices with dual-NIC mainboards. Some are Realtek NICs, which suck. Some are Intel e1000s, which don't. I've just noticed on 2 machines, one is an Intel NIC, one is a Realtek, that when I put the MAC address of one machine into the dhcpd.conf file on our DHCP server to get it to PXE boot the machine into a rebuild environment, initially everything is fine. The server gets a DHCP allocation, and PXE boots into the Ubuntu preseed enviroment. On one or two machines, it gets as far as Ubuntu's DHCP network configuration, and fails. If i pull up a busybox shell (on tty2 on the installing machine), and run ip link, I can see that the UP flag is set on the other NIC. Here's some stuff. host xeon16-ghz240-gb48-node1 { hardware ethernet BC:AE:C5:07:1F:18; filename "pxelinux.0"; next-server 192.168.123.80; } That's what's in dhcpd.conf This is what ip link on the evil machine looks like. Only one NIC is actually connected (deliberately). As you can see, the NIC that's in the dhcpd config, is not marked as UP, and the link that is UP, isn't the one in DHCP. So far I've seen this on two brands of dual-NIC configuration. Does anyone know 1) what's causing it, and b) What we can do about it?

    Read the article

  • Can I run a mix of static addressing and NAT?

    - by aroth
    Let's say that an ISP offers a plan with 5 static IP addresses, but I have more than 5 devices, many of which (such as a networked printer, for instance) I do not want or need to have a static IP address. So the topography I'm planning goes something like: ISP -> Router -> Switch -> Computer (static address) -> Computer (static address) -> Printer (DHCP/NAT) -> Tv (DHCP/NAT) -> (...) -> Wireless Devices (DHCP/NAT) Generally speaking, is it possible to run a network like that? If not, then what sort of setup do I need so that I can assign static addresses just to the things that need them, and use DHCP/NAT for everything else? Also, what internal networking devices will consume a static IP address? I'm pretty sure the router will, correct? Does the switch also?

    Read the article

  • Webmin ADSL module

    - by expatcm
    I was wondering if the Webmin ADSL module is going to help me solve a problem .... but I cannot find any documentation telling me what the module does ..... Any ideas? What I am hoping is that it will solve a problem .... I am just in the process of setting up a Debian server. I will use the DHCP server as part of the Debian setup to manage the lan IP addresses. I want to turn off the external DHCP server which is part of the Linksys ADSL modem / router and use just the modem. The challenge I have is knowing what I need to do in order to get the public DNS on the eth1. When I turn off the DHCP on the modem / router not a lot happens apart from no longer being able to access the settings .......... So I am looking at this Webmin module and wondering if it is to manage the ADSL connection and find the public DNS address .... The local DHCP server is working well for the lan, I am just stuck for the external DNS.

    Read the article

  • fedora, dhcpd fails to start

    - by soxs060389
    History: I got a tiny shiny plugserver which I want to plug to my ADSL router (or however you want to call it) on one end (eth0), and the other end (eth1) I want to run a dhcp server for my LAN. ATM I am stuck with getting LAN to work. OS is fedora 12. I configured my /etc/dhcp/dhcpd.conf like this: # # DHCP Server Configuration file. # see /usr/share/doc/dhcp*/dhcpd.conf.sample # see 'man 5 dhcpd.conf' # option domain-name "unknown.org"; option domain-name-servers 192.168.44.1; option subnet-mask 255.255.255.0; option broadcast-address 192.168.44.255; default-lease-time 86400; max-lease-time 172800; subnet 192.168.44.0 netmask 255.255.255.0 { host fedorabigbox { hardware ethernet 00:19:66:8E:61:74; fixed-address 192.168.44.21; } #host mobile #{ # hardware ethernet ***; # fixed-address 192.168.44.22; #} range 192.168.44.100 192.168.44.110; option routers 192.168.44.1; } # this is just dummy, as read many howtos, some suggesting to add a subnet blah netmask blah for each interface subnet 192.168.33.0 netmask 255.255.255.0 { range 192.168.33.100 192.168.33.110; option routers 192.168.33.1; } But the server fails to start when trying to start it via /etc/init.d/dhcpd start In general it would be nice if someone can point me to a in detail explanation of how network works, I am pretty new to this stuff. More concrete question: How to point the subnets to eth1 and the other to eth0, how can this be achieved? Does someone see any errors or flaws? Syntax should be correct, allready checked that with the dhcpd syntax check. Thanks for any help

    Read the article

  • Hyper-V: Dedicated NIC for Guests VMs

    - by TheLizardKing
    I have two NIC cards and created a private virtual network for my virtual machines and unchecked "Allow management operating system to share this network adapter" which basically turns my Guest NIC into this sorta shell of a NIC card on the host machine and the only thing checked in it's properties is "Microsoft Virtual Network Switch Protocol" which I am fine with. Everything works and everything is connected. My issue is that for some reason my guest (Ubuntu Server with legacy network drivers) is not talking properly to my DHCP server. Specifically my DHCP server reserves the guest's IP address using it's MAC address but the guest isn't picking it up. It's picking up any old IP it can get and I can't even ping the hostname from another PC on the network but it pings fine if I use the IP. I see the guest showing up in my DHCP table but I can't get the reservation to stick. Is there some reason it's only partially communicating with my DHCP server? Pinging it's hostname on itself reveals it's using 127.0.0.1 instead of it's network IP. Is this an issue with the legacy drivers used in Hyper-V?

    Read the article

  • Arch Linux: eth0 no carrier - network fails at boot

    - by user905686
    The problem My computer is connected to a network where dhcp is required. So my network configuration in /etc/rc.conf looks like interface=eth0 address= netmask= broadcast= gateway= My deamons are DAEMONS=(!hwclock syslog-ng network netfs crond ntpd) With this configuration, Arch hangs at boot a long time at "Network" (Still it says "[done]", but after boot I have no connection). I found out two workaround: Workaround 1 remove network from deamons run mii-tool --reset eth0 and dhcpcd eth0 after boot (somehow it does not work when placing these commands in /etc/rc.local. Then dhcp work very quickly (because of the reset!). Before executing the first command, ip link show eth0 has "NO CARRIER" in output. Afterwards, it doesn´t. (Also, mii-tool first shows "no link", afterwards eth0: 10 Mbit, half duplex, link ok. Workaround 2 Change network configuration to interface=eth0 address=x.y.z.21 netmask=255.255.255.0 broadcast=xxx.y.z.255 gateway=x.y.z.254 whereas x, y, z build the specific adresses of the network (Though dhcp is used, I get a static ip). Add the commands mii-tool --reset eth0 and dhcpcd eth0 to /etc/rc.local Now network starts quickly at boot (though I don´t know if successfully), the commands in /etc/rc.local are executed and the connection is fine after login. What to do? So the problem seems to be that dhcpcd stucks at "wating for carrier" or sth. I do not like the workaround, because some deamons need network (though they seem to start). What can I do to have eth0 ready for dhcp at boot? Or is there another problem?

    Read the article

  • Internet doesn't work by default

    - by Adam Martinez
    After upgrading to Precise, I am required to run 'sudo dhclient eth0' in a terminal in order to get the internet to work. Everything worked perfectly fine on Oneiric, so It's really puzzling me. I'm thinking it could possibly be something with the kernel, but who knows. Output of dmesg: [ 0.247891] system 00:01: [io 0x0290-0x030f] has been reserved [ 0.247896] system 00:01: [io 0x0290-0x0297] has been reserved [ 0.247901] system 00:01: [io 0x0880-0x088f] has been reserved [ 0.247908] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.247931] pnp 00:02: [dma 4] [ 0.247935] pnp 00:02: [io 0x0000-0x000f] [ 0.247939] pnp 00:02: [io 0x0080-0x0090] [ 0.247943] pnp 00:02: [io 0x0094-0x009f] [ 0.247947] pnp 00:02: [io 0x00c0-0x00df] [ 0.248033] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active) [ 0.248125] pnp 00:03: [io 0x0070-0x0073] [ 0.248187] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.248205] pnp 00:04: [io 0x0061] [ 0.248260] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active) [ 0.248277] pnp 00:05: [io 0x00f0-0x00ff] [ 0.248292] pnp 00:05: [irq 13] [ 0.248348] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active) [ 0.248583] pnp 00:06: [io 0x03f0-0x03f5] [ 0.248588] pnp 00:06: [io 0x03f7] [ 0.248597] pnp 00:06: [irq 6] [ 0.248601] pnp 00:06: [dma 2] [ 0.248690] pnp 00:06: Plug and Play ACPI device, IDs PNP0700 (active) [ 0.248998] pnp 00:07: [io 0x03f8-0x03ff] [ 0.249008] pnp 00:07: [irq 4] [ 0.249122] pnp 00:07: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.249479] pnp 00:08: [io 0x0400-0x04bf] [ 0.249584] system 00:08: [io 0x0400-0x04bf] has been reserved [ 0.249591] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.249628] pnp 00:09: [mem 0xffb80000-0xffbfffff] [ 0.249690] pnp 00:09: Plug and Play ACPI device, IDs INT0800 (active) [ 0.250049] pnp 00:0a: [mem 0xe0000000-0xefffffff] [ 0.250167] system 00:0a: [mem 0xe0000000-0xefffffff] has been reserved [ 0.250173] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.250302] pnp 00:0b: [mem 0x000f0000-0x000fffff] [ 0.250307] pnp 00:0b: [mem 0x7ff00000-0x7fffffff] [ 0.250311] pnp 00:0b: [mem 0xfed00000-0xfed000ff] [ 0.250316] pnp 00:0b: [mem 0x0000046e-0x0000056d] [ 0.250320] pnp 00:0b: [mem 0x7fee0000-0x7fefffff] [ 0.250324] pnp 00:0b: [mem 0x00000000-0x0009ffff] [ 0.250328] pnp 00:0b: [mem 0x00100000-0x7fedffff] [ 0.250332] pnp 00:0b: [mem 0xfec00000-0xfec00fff] [ 0.250336] pnp 00:0b: [mem 0xfed14000-0xfed1dfff] [ 0.250341] pnp 00:0b: [mem 0xfed20000-0xfed9ffff] [ 0.250345] pnp 00:0b: [mem 0xfee00000-0xfee00fff] [ 0.250349] pnp 00:0b: [mem 0xffb00000-0xffb7ffff] [ 0.250353] pnp 00:0b: [mem 0xfff00000-0xffffffff] [ 0.250357] pnp 00:0b: [mem 0x000e0000-0x000effff] [ 0.250409] pnp 00:0b: disabling [mem 0x0000046e-0x0000056d] because it overlaps 0000:01:00.0 BAR 6 [mem 0x00000000-0x0007ffff pref] [ 0.250419] pnp 00:0b: disabling [mem 0x0000046e-0x0000056d disabled] because it overlaps 0000:03:00.0 BAR 6 [mem 0x00000000-0x0000ffff pref] [ 0.250430] pnp 00:0b: disabling [mem 0x0000046e-0x0000056d disabled] because it overlaps 0000:04:00.0 BAR 6 [mem 0x00000000-0x0001ffff pref] [ 0.250524] system 00:0b: [mem 0x000f0000-0x000fffff] could not be reserved [ 0.250530] system 00:0b: [mem 0x7ff00000-0x7fffffff] has been reserved [ 0.250536] system 00:0b: [mem 0xfed00000-0xfed000ff] has been reserved [ 0.250541] system 00:0b: [mem 0x7fee0000-0x7fefffff] could not be reserved [ 0.250547] system 00:0b: [mem 0x00000000-0x0009ffff] could not be reserved [ 0.250552] system 00:0b: [mem 0x00100000-0x7fedffff] could not be reserved [ 0.250558] system 00:0b: [mem 0xfec00000-0xfec00fff] could not be reserved [ 0.250563] system 00:0b: [mem 0xfed14000-0xfed1dfff] has been reserved [ 0.250568] system 00:0b: [mem 0xfed20000-0xfed9ffff] has been reserved [ 0.250574] system 00:0b: [mem 0xfee00000-0xfee00fff] has been reserved [ 0.250579] system 00:0b: [mem 0xffb00000-0xffb7ffff] has been reserved [ 0.250585] system 00:0b: [mem 0xfff00000-0xffffffff] has been reserved [ 0.250590] system 00:0b: [mem 0x000e0000-0x000effff] has been reserved [ 0.250596] system 00:0b: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.250614] pnp: PnP ACPI: found 12 devices [ 0.250617] ACPI: ACPI bus type pnp unregistered [ 0.250624] PnPBIOS: Disabled by ACPI PNP [ 0.288725] PCI: max bus depth: 1 pci_try_num: 2 [ 0.288786] pci 0000:01:00.0: BAR 6: assigned [mem 0xfb000000-0xfb07ffff pref] [ 0.288792] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 0.288797] pci 0000:00:01.0: bridge window [io 0xa000-0xafff] [ 0.288804] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xfbffffff] [ 0.288811] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 0.288820] pci 0000:00:1c.0: PCI bridge to [bus 02-02] [ 0.288825] pci 0000:00:1c.0: bridge window [io 0x9000-0x9fff] [ 0.288833] pci 0000:00:1c.0: bridge window [mem 0xfdb00000-0xfdbfffff] [ 0.288840] pci 0000:00:1c.0: bridge window [mem 0xfd800000-0xfd8fffff 64bit pref] [ 0.288851] pci 0000:03:00.0: BAR 6: assigned [mem 0xfde00000-0xfde0ffff pref] [ 0.288856] pci 0000:00:1c.4: PCI bridge to [bus 03-03] [ 0.288861] pci 0000:00:1c.4: bridge window [io 0xd000-0xdfff] [ 0.288869] pci 0000:00:1c.4: bridge window [mem 0xfd700000-0xfd7fffff] [ 0.288876] pci 0000:00:1c.4: bridge window [mem 0xfde00000-0xfdefffff 64bit pref] [ 0.288887] pci 0000:04:00.0: BAR 6: assigned [mem 0xfdc00000-0xfdc1ffff pref] [ 0.288891] pci 0000:00:1c.5: PCI bridge to [bus 04-04] [ 0.288897] pci 0000:00:1c.5: bridge window [io 0xb000-0xbfff] [ 0.288904] pci 0000:00:1c.5: bridge window [mem 0xfdd00000-0xfddfffff] [ 0.288911] pci 0000:00:1c.5: bridge window [mem 0xfdc00000-0xfdcfffff 64bit pref] [ 0.288920] pci 0000:00:1e.0: PCI bridge to [bus 05-05] [ 0.288926] pci 0000:00:1e.0: bridge window [io 0xc000-0xcfff] [ 0.288933] pci 0000:00:1e.0: bridge window [mem 0xfda00000-0xfdafffff] [ 0.288940] pci 0000:00:1e.0: bridge window [mem 0xfd900000-0xfd9fffff 64bit pref] [ 0.288971] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.288979] pci 0000:00:01.0: setting latency timer to 64 [ 0.288991] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.288998] pci 0000:00:1c.0: setting latency timer to 64 [ 0.289008] pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.289014] pci 0000:00:1c.4: setting latency timer to 64 [ 0.289030] pci 0000:00:1c.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 0.289037] pci 0000:00:1c.5: setting latency timer to 64 [ 0.289047] pci 0000:00:1e.0: setting latency timer to 64 [ 0.289054] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 0.289058] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 0.289063] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 0.289067] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff] [ 0.289072] pci_bus 0000:00: resource 8 [mem 0x7ff00000-0xfebfffff] [ 0.289077] pci_bus 0000:01: resource 0 [io 0xa000-0xafff] [ 0.289081] pci_bus 0000:01: resource 1 [mem 0xf8000000-0xfbffffff] [ 0.289086] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref] [ 0.289092] pci_bus 0000:02: resource 0 [io 0x9000-0x9fff] [ 0.289096] pci_bus 0000:02: resource 1 [mem 0xfdb00000-0xfdbfffff] [ 0.289101] pci_bus 0000:02: resource 2 [mem 0xfd800000-0xfd8fffff 64bit pref] [ 0.289106] pci_bus 0000:03: resource 0 [io 0xd000-0xdfff] [ 0.289110] pci_bus 0000:03: resource 1 [mem 0xfd700000-0xfd7fffff] [ 0.289115] pci_bus 0000:03: resource 2 [mem 0xfde00000-0xfdefffff 64bit pref] [ 0.289120] pci_bus 0000:04: resource 0 [io 0xb000-0xbfff] [ 0.289124] pci_bus 0000:04: resource 1 [mem 0xfdd00000-0xfddfffff] [ 0.289129] pci_bus 0000:04: resource 2 [mem 0xfdc00000-0xfdcfffff 64bit pref] [ 0.289134] pci_bus 0000:05: resource 0 [io 0xc000-0xcfff] [ 0.289138] pci_bus 0000:05: resource 1 [mem 0xfda00000-0xfdafffff] [ 0.289143] pci_bus 0000:05: resource 2 [mem 0xfd900000-0xfd9fffff 64bit pref] [ 0.289148] pci_bus 0000:05: resource 4 [io 0x0000-0x0cf7] [ 0.289152] pci_bus 0000:05: resource 5 [io 0x0d00-0xffff] [ 0.289157] pci_bus 0000:05: resource 6 [mem 0x000a0000-0x000bffff] [ 0.289161] pci_bus 0000:05: resource 7 [mem 0x000c0000-0x000dffff] [ 0.289166] pci_bus 0000:05: resource 8 [mem 0x7ff00000-0xfebfffff] [ 0.289233] NET: Registered protocol family 2 [ 0.289360] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.289754] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.290351] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.290670] TCP: Hash tables configured (established 131072 bind 65536) [ 0.290674] TCP reno registered [ 0.290680] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.290703] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.290868] NET: Registered protocol family 1 [ 0.290911] pci 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.290932] pci 0000:00:1a.0: PCI INT A disabled [ 0.290956] pci 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 0.290975] pci 0000:00:1a.1: PCI INT B disabled [ 0.290992] pci 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [ 0.291012] pci 0000:00:1a.2: PCI INT D disabled [ 0.291031] pci 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.291068] pci 0000:00:1a.7: PCI INT C disabled [ 0.291104] pci 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.291123] pci 0000:00:1d.0: PCI INT A disabled [ 0.291135] pci 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.291155] pci 0000:00:1d.1: PCI INT B disabled [ 0.291166] pci 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.291185] pci 0000:00:1d.2: PCI INT C disabled [ 0.291198] pci 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.291219] pci 0000:00:1d.7: PCI INT A disabled [ 0.291258] pci 0000:01:00.0: Boot video device [ 0.291273] PCI: CLS 4 bytes, default 64 [ 0.291857] audit: initializing netlink socket (disabled) [ 0.291876] type=2000 audit(1336753420.284:1): initialized [ 0.337724] highmem bounce pool size: 64 pages [ 0.337734] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.349241] VFS: Disk quotas dquot_6.5.2 [ 0.349365] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.350418] fuse init (API version 7.17) [ 0.350611] msgmni has been set to 1685 [ 0.351179] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.351229] io scheduler noop registered [ 0.351233] io scheduler deadline registered [ 0.351247] io scheduler cfq registered (default) [ 0.351450] pcieport 0000:00:01.0: setting latency timer to 64 [ 0.351502] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X [ 0.351585] pcieport 0000:00:1c.0: setting latency timer to 64 [ 0.351639] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X [ 0.351728] pcieport 0000:00:1c.4: setting latency timer to 64 [ 0.351779] pcieport 0000:00:1c.4: irq 42 for MSI/MSI-X [ 0.351875] pcieport 0000:00:1c.5: setting latency timer to 64 [ 0.351927] pcieport 0000:00:1c.5: irq 43 for MSI/MSI-X [ 0.352094] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.352143] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 0.352311] intel_idle: MWAIT substates: 0x22220 [ 0.352315] intel_idle: does not run on family 6 model 23 [ 0.352446] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0 [ 0.352455] ACPI: Power Button [PWRB] [ 0.352556] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 0.352562] ACPI: Power Button [PWRF] [ 0.352650] ACPI: Fan [FAN] (on) [ 0.355667] thermal LNXTHERM:00: registered as thermal_zone0 [ 0.355673] ACPI: Thermal Zone [THRM] (26 C) [ 0.355750] ERST: Table is not found! [ 0.355753] GHES: HEST is not enabled! [ 0.355898] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 0.376332] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 0.376582] isapnp: Scanning for PnP cards... [ 0.709133] Freeing initrd memory: 13792k freed [ 0.729743] isapnp: No Plug & Play device found [ 0.816786] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 0.832385] Linux agpgart interface v0.103 [ 0.835605] brd: module loaded [ 0.837138] loop: module loaded [ 0.837452] ata_piix 0000:00:1f.2: version 2.13 [ 0.837473] ata_piix 0000:00:1f.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 0.837480] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] [ 0.837546] ata_piix 0000:00:1f.2: setting latency timer to 64 [ 0.838099] scsi0 : ata_piix [ 0.838253] scsi1 : ata_piix [ 0.839183] ata1: SATA max UDMA/133 cmd 0xf900 ctl 0xf800 bmdma 0xf500 irq 19 [ 0.839192] ata2: SATA max UDMA/133 cmd 0xf700 ctl 0xf600 bmdma 0xf508 irq 19 [ 0.839239] ata_piix 0000:00:1f.5: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 0.839246] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ] [ 0.839300] ata_piix 0000:00:1f.5: setting latency timer to 64 [ 0.839708] scsi2 : ata_piix [ 0.839841] scsi3 : ata_piix [ 0.840301] ata3: SATA max UDMA/133 cmd 0xf200 ctl 0xf100 bmdma 0xee00 irq 19 [ 0.840308] ata4: SATA max UDMA/133 cmd 0xf000 ctl 0xef00 bmdma 0xee08 irq 19 [ 0.840429] pata_acpi 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.840467] pata_acpi 0000:03:00.0: setting latency timer to 64 [ 0.840488] pata_acpi 0000:03:00.0: PCI INT A disabled [ 0.841159] Fixed MDIO Bus: probed [ 0.841205] tun: Universal TUN/TAP device driver, 1.6 [ 0.841210] tun: (C) 1999-2004 Max Krasnyansky <[email protected]> [ 0.841322] PPP generic driver version 2.4.2 [ 0.841515] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.841542] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.841567] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [ 0.841573] ehci_hcd 0000:00:1a.7: EHCI Host Controller [ 0.841658] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 [ 0.845582] ehci_hcd 0000:00:1a.7: cache line size of 4 is not supported [ 0.845610] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfdfff000 [ 0.860022] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 [ 0.860264] hub 1-0:1.0: USB hub found [ 0.860272] hub 1-0:1.0: 6 ports detected [ 0.860404] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.860424] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 0.860430] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 0.860512] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 0.864413] ehci_hcd 0000:00:1d.7: cache line size of 4 is not supported [ 0.864438] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfdffe000 [ 0.880021] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 0.880227] hub 2-0:1.0: USB hub found [ 0.880234] hub 2-0:1.0: 6 ports detected [ 0.880369] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.880396] uhci_hcd: USB Universal Host Controller Interface driver [ 0.880431] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.880443] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [ 0.880449] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 0.880529] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 [ 0.880574] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000ff00 [ 0.880803] hub 3-0:1.0: USB hub found [ 0.880811] hub 3-0:1.0: 2 ports detected [ 0.880929] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 0.880940] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [ 0.880946] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 0.881039] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 [ 0.881081] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000fe00 [ 0.881302] hub 4-0:1.0: USB hub found [ 0.881310] hub 4-0:1.0: 2 ports detected [ 0.881427] uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [ 0.881438] uhci_hcd 0000:00:1a.2: setting latency timer to 64 [ 0.881443] uhci_hcd 0000:00:1a.2: UHCI Host Controller [ 0.881523] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 [ 0.881551] uhci_hcd 0000:00:1a.2: irq 19, io base 0x0000fd00 [ 0.881774] hub 5-0:1.0: USB hub found [ 0.881781] hub 5-0:1.0: 2 ports detected [ 0.881899] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.881910] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 0.881915] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 0.881993] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 [ 0.882021] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000fc00 [ 0.882244] hub 6-0:1.0: USB hub found [ 0.882252] hub 6-0:1.0: 2 ports detected [ 0.882370] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.882381] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 0.882386] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 0.882467] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 [ 0.882495] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000fb00 [ 0.882735] hub 7-0:1.0: USB hub found [ 0.882742] hub 7-0:1.0: 2 ports detected [ 0.882858] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.882869] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 0.882875] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 0.882954] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 [ 0.882982] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000fa00 [ 0.883205] hub 8-0:1.0: USB hub found [ 0.883213] hub 8-0:1.0: 2 ports detected [ 0.883435] usbcore: registered new interface driver libusual [ 0.883535] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 0.883926] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 0.883936] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 0.884187] mousedev: PS/2 mouse device common for all mice [ 0.884433] rtc_cmos 00:03: RTC can wake from S4 [ 0.884582] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 [ 0.884612] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs [ 0.884719] device-mapper: uevent: version 1.0.3 [ 0.884854] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected] [ 0.884917] EISA: Probing bus 0 at eisa.0 [ 0.884921] EISA: Cannot allocate resource for mainboard [ 0.884925] Cannot allocate resource for EISA slot 1 [ 0.884929] Cannot allocate resource for EISA slot 2 [ 0.884932] Cannot allocate resource for EISA slot 3 [ 0.884936] Cannot allocate resource for EISA slot 4 [ 0.884940] Cannot allocate resource for EISA slot 5 [ 0.884943] Cannot allocate resource for EISA slot 6 [ 0.884947] Cannot allocate resource for EISA slot 7 [ 0.884950] Cannot allocate resource for EISA slot 8 [ 0.884954] EISA: Detected 0 cards. [ 0.884969] cpufreq-nforce2: No nForce2 chipset. [ 0.884973] cpuidle: using governor ladder [ 0.884976] cpuidle: using governor menu [ 0.884980] EFI Variables Facility v0.08 2004-May-17 [ 0.885476] TCP cubic registered [ 0.885708] NET: Registered protocol family 10 [ 0.886771] NET: Registered protocol family 17 [ 0.886799] Registering the dns_resolver key type [ 0.886837] Using IPI No-Shortcut mode [ 0.887028] PM: Hibernation image not present or could not be loaded. [ 0.887047] registered taskstats version 1 [ 0.902579] Magic number: 12:339:388 [ 0.902592] usb usb6: hash matches [ 0.902687] rtc_cmos 00:03: setting system clock to 2012-05-11 16:23:41 UTC (1336753421) [ 0.903185] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 0.903189] EDD information not available. [ 1.170710] ata3: SATA link down (SStatus 0 SControl 300) [ 1.181439] ata4: SATA link down (SStatus 0 SControl 300) [ 1.288020] Refined TSC clocksource calibration: 2499.999 MHz. [ 1.288028] Switching to clocksource tsc [ 1.292016] usb 1-5: new high-speed USB device number 3 using ehci_hcd [ 1.486745] ata2.00: SATA link down (SStatus 0 SControl 300) [ 1.486762] ata2.01: SATA link down (SStatus 0 SControl 300) [ 1.640115] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.640130] ata1.01: SATA link down (SStatus 0 SControl 300) [ 1.648342] ata1.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133 [ 1.648348] ata1.00: 490234752 sectors, multi 0: LBA48 [ 1.664325] ata1.00: configured for UDMA/133 [ 1.664531] scsi 0:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5 [ 1.664745] sd 0:0:0:0: [sda] 490234752 512-byte logical blocks: (251 GB/233 GiB) [ 1.664809] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 1.664838] sd 0:0:0:0: [sda] Write Protect is off [ 1.664843] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.664884] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.691699] sda: sda1 sda2 sda3 sda4 [ 1.692348] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.692461] Freeing unused kernel memory: 740k freed [ 1.692820] Write protecting the kernel text: 5828k [ 1.692851] Write protecting the kernel read-only data: 2376k [ 1.692854] NX-protecting the kernel data: 4412k [ 1.723980] udevd[92]: starting version 175 [ 1.865339] Floppy drive(s): fd0 is 1.44M [ 1.865429] pata_jmicron 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.865478] pata_jmicron 0000:03:00.0: setting latency timer to 64 [ 1.867875] sky2: driver version 1.30 [ 1.867926] sky2 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1.867942] sky2 0000:04:00.0: setting latency timer to 64 [ 1.867979] sky2 0000:04:00.0: Yukon-2 EC chip revision 2 [ 1.868111] sky2 0000:04:00.0: irq 44 for MSI/MSI-X [ 1.868174] scsi4 : pata_jmicron [ 1.869802] sky2 0000:04:00.0: eth0: addr 00:01:29:a4:16:0a [ 1.869828] scsi5 : pata_jmicron [ 1.869943] ata5: PATA max UDMA/100 cmd 0xdf00 ctl 0xde00 bmdma 0xdb00 irq 16 [ 1.869949] ata6: PATA max UDMA/100 cmd 0xdd00 ctl 0xdc00 bmdma 0xdb08 irq 16 [ 1.880053] usb 4-1: new full-speed USB device number 2 using uhci_hcd [ 1.884052] FDC 0 is a post-1991 82077 [ 2.032611] ata5.00: ATAPI: _NEC DVD+/-RW ND-3450A, 103C, max UDMA/33 [ 2.048585] ata5.00: configured for UDMA/33 [ 2.049777] scsi 4:0:0:0: CD-ROM _NEC DVD+-RW ND-3450A 103C PQ: 0 ANSI: 5 [ 2.051048] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray [ 2.051054] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 2.051283] sr 4:0:0:0: Attached scsi CD-ROM sr0 [ 2.051483] sr 4:0:0:0: Attached scsi generic sg1 type 5 [ 2.079838] usbcore: registered new interface driver usbhid [ 2.079844] usbhid: USB HID core driver [ 2.236660] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 12.150230] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 12.177342] udevd[333]: starting version 175 [ 12.195524] Adding 417684k swap on /dev/sda2. Priority:-1 extents:1 across:417684k [ 12.278032] lp: driver loaded but no devices found [ 12.516456] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1a.1-1/input2 [ 12.520297] input: Logitech Unifying Device. Wireless PID:1024 as /devices/pci0000:00/0000:00:1a.1/usb4/4-1/4-1:1.2/0003:046D:C52B.0003/input/input2 [ 12.520753] logitech-djdevice 0003:046D:C52B.0004: input,hidraw1: USB HID v1.11 Mouse [Logitech Unifying Device. Wireless PID:1024] on usb-0000:00:1a.1-1:1 [ 12.523286] input: Logitech Unifying Device. Wireless PID:2011 as /devices/pci0000:00/0000:00:1a.1/usb4/4-1/4-1:1.2/0003:046D:C52B.0003/input/input3 [ 12.524439] logitech-djdevice 0003:046D:C52B.0005: input,hidraw2: USB HID v1.11 Keyboard [Logitech Unifying Device. Wireless PID:2011] on usb-0000:00:1a.1-1:2 [ 12.545746] type=1400 audit(1336771433.137:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=502 comm="apparmor_parser" [ 12.546574] type=1400 audit(1336771433.137:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=502 comm="apparmor_parser" [ 12.547034] type=1400 audit(1336771433.137:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=502 comm="apparmor_parser" [ 12.626869] Linux video capture interface: v2.00 [ 12.649104] uvcvideo: Found UVC 1.00 device <unnamed> (046d:081a) [ 12.668665] input: UVC Camera (046d:081a) as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5:1.0/input/input4 [ 12.668909] usbcore: registered new interface driver uvcvideo [ 12.668914] USB Video Class driver (1.1.1) [ 12.697645] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 12.697721] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X [ 12.697760] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 12.706772] nvidia: module license 'NVIDIA' taints kernel. [ 12.706778] Disabling lock debugging due to kernel taint [ 12.735428] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 13.350252] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 13.350267] nvidia 0000:01:00.0: setting latency timer to 64 [ 13.350275] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem [ 13.351464] NVRM: loading NVIDIA UNIX x86 Kernel Module 295.40 Thu Apr 5 21:28:09 PDT 2012 [ 13.356785] hda_codec: ALC889A: BIOS auto-probing. [ 13.357267] init: failsafe main process (658) killed by TERM signal [ 13.372756] input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5 [ 13.373173] input: HDA Intel Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6 [ 13.373568] input: HDA Intel Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7 [ 13.373954] input: HDA Intel Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8 [ 13.374339] input: HDA Intel Line-Out Side as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9 [ 13.374715] input: HDA Intel Line-Out CLFE as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10 [ 13.375109] input: HDA Intel Line-Out Surround as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11 [ 13.375724] input: HDA Intel Line-Out Front as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 [ 13.475252] type=1400 audit(1336771434.065:5): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=735 comm="apparmor_parser" [ 13.477026] type=1400 audit(1336771434.069:6): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=735 comm="apparmor_parser" [ 13.477695] type=1400 audit(1336771434.069:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=735 comm="apparmor_parser" [ 13.479048] type=1400 audit(1336771434.069:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=734 comm="apparmor_parser" [ 13.488994] type=1400 audit(1336771434.081:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=738 comm="apparmor_parser" [ 13.489972] type=1400 audit(1336771434.081:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=738 comm="apparmor_parser" [ 13.

    Read the article

  • vlan change via scvmm not working

    - by HarryMud
    Hi i have a windows 2008 R2 hyper-v server which is managed via scvmm 2008 R2. the guest os running on the hyper-v server is winxp with sp3. if i change the vlan id via scvmm the guest doesn't get an ip via dhcp i looked in the properties of the vm with the hyper-v mmc an see the vlan changed correctly but no ip connectivity either static or dhcp a reboot of the guest os didn't help if i change the vlan id via hyper-v mmc the guest gets an ip via dhcp scvmm seams to forget something after the vlan change has anyone a clue how to resolve this ? thx

    Read the article

  • Assigning security groups different ranges

    - by Mustafa Ismail Mustafa
    Is it possible to assign a security group in windows 2008 a specific DHCP scope? Meaning, let's say we have 2 groups, employees and managers in the superscope Company. Assuming that each user is distinctly in either group and there are no overlaps, would it be possible to assign members of the security group employees a dhcp address in the range 192.168.1.0/24 and managers 192.168.2.0/24 ? The DHCP server is the same server. This is on Windows SBS 2008 if it makes any difference If it is possible, how do you go about setting it up. TIA

    Read the article

  • How to use auto-discovery with iDRAC Enterprise?

    - by jwiz
    All I want to do is: have "auto discovery" enabled on my iDRAC enterprise at the factory rack the server, cable iDRAC to dhcp-enabled management network have the iDRAC DHCP, find the "Provisioning Server", and get updated with login credentials (for us to use with racadm, idrac webui, etc.) I don't need to do any configuring of the system, install OS, or anything else. I just want idrac to dhcp out of the box, and end up with an account that can be used to login. All the docs I can find on Dell's site refer to a "Provisioning Server", but I honestly can't tell if they have some reference product, or if they only have software that "integrates" with other vendor's existing management systems. I'd be happy to set up whatever is needed, I just can't find something that explicitly describes the process (only references to the fact that it is supported).

    Read the article

  • Edimax wireless router is not providing DNS services correctly

    - by Nathan Fellman
    I have an Edimax router that is set up to connect to the internet via L2TP on cable, and on the LAN side it's set up as a DHCP server. The DHCP server gives correct IP addresses, but it sets itself up as the DNS server. However, it doesn't provide the DNS service. I am sure that it's a problem with the router, because I have two computers on the network with the same problem. I see that on the WAN side it gets correct DNS addresses from the ISP, so I'd expect the router to either pass these addresses through to the DHCP clients, or to serve the DNS requests itself by forwarding them to the ISP's DNS. However, it apparently does neither, and there is no DNS. I switched from ADSL to cable last week. On ADSL it connected using PPPoE, and the DNS worked fine. What can be the problem here?

    Read the article

  • What equipment do real ISP's use?

    - by Allanrbo
    In a dormitory of 550 residents, people often mistakenly set up DHCP servers for the whole network by plugging in their private Wi-Fi routers wrongly. Also recently, someone mistakenly configured their PC to a static IP being the same as that of the default gateway. We use cheap 3Com switches at the moment. I know that Cisco switches support DHCP snooping to solve the DHCP problem, but that still does not solve the default gateway IP takeover problem. What sort of switch equipment do real ISP's use so their customers cannot break the network for the other customers?

    Read the article

  • Multiple Subnets on home network... would this work?

    - by rockinthesixstring
    We are looking at renting out the basement suit in our home and want to offer internet as part of the package. I however do not want the downstairs tennent to have access to our network (home office = private data). We currently have a pfsense firewall as our gateway and a Windows Server 2003 box is doing our primary DHCP (192.168.0.0/24) and DNS. Here's what I'd like to do... I'd like to setup another subnet on the DHCP server (192.168.1.0/24), and hook in another wireless router (as access point only) and address it as 192.168.1.1... from there the router will hook into our primary switch and then out through the firewall. Will Server 2003 (If I add a 192.168.1.x/24 IP to the nic) serve DHCP to the devices that connect to the new router, and will it isolate that from our network? Thanks in advance... I'm very new to multiple subnets.

    Read the article

< Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >