Search Results

Search found 294 results on 12 pages for 'heat'.

Page 12/12 | < Previous Page | 8 9 10 11 12 

  • Server Cabinet/Room Cooling

    - by user37226
    Hello all. I currently have two desktops and three servers in my office sitting on the floor (I know this is bad). With that many servers the ambient temperature in the room goes up quickly. I am located in Dallas, TX so during the winter, if the heat is kept low, it is not a problem, but during the summer it easily jumps the room +10 degrees. I have decided and found a free 42U server cabinet that a hosting company was throwing away to house all of these systems in. One server is in a rack mount case while the other four servers are housed in mid-tower cases. I have purchased shelves for each computer and plan to lay the towers side ways on these shelves (as replacing the cases costs a heck of a lot of money). I like the idea of housing all of these systems in the cabinet because it will save a lot of room and clean up all of the cabling currently laying all over the office floor. When putting this setup together over the next couple of weeks, I want to address issues with dust and cooling. The server cabinet has a fan on top, front plexiglass door and a rear metal door with vent wholes on the bottom. First the cooling issues. I know I am going to want to have cool air enter the bottom of the cabinet and exit the top. I do not want the room heating up though as this will make my work area hot and then make the servers warmer as the air eventually reenters the cabinet. I had an idea to fix this problem, but am unsure if it will work. I was thinking of taking flexible piping and adapting it to the back fans of the computer having the other end of the pipe at the top close to the cabinet's top mounted fan. I was then thinking of creating a duct around the top fan into the attic. Now I am very concerned that the attic will cause issues with this type of setup because during July/August time frame, the attic is easily 120 degrees F. I could also use the flexible pipe to take it to an attic exhaust vent if it would be better to vent it into the 100 degree air outside (at least there may be wind. The other option would be to buy a small portable air conditioner. This may be a possibility, but do I want to spend the extra money on power? I bet this increases the noise. Plus they are around $250 on Amazon. What would you all recommend? Depending on the solution I end up running with above, I would also like to limit the dust that gets into the cabinet. If I were to cut a whole and mount a second cabinet fan on the bottom of the rear door, could I possibly mount a standard home air filter on the other side of that whole? Thanks in advance for your recommendations. I look forward to reading your interesting ideas.

    Read the article

  • Thoughts on home NAS server

    - by user826955
    I currently have a NAS with a 2x2TB HDD 1x16GB SSD layout on a mini-itx atom board. The NAS is in a Lian Li PC-Q07 case. On this system I was running freebsd 8 with a gmirror raid 1 setup, which was enough for my needs. So far I was using the NAS for: Fileserver with AFP protocol (only mac clients used) SVN server hosting all my source trees of my projects JIRA (performance was okay-ish) Timemachine backup for the macs The power consumption was about 38W, although I did not put HDDs asleep when unused (I think this is not possible in a raid setup). I liked the NAS because: the performance was good through gigabit LAN (enough for my needs) power consumption was good its a pretty small case and fits in one of my cupboards I disliked the NAS a bit because: it was a bit noisy, the Q07 case vibrated a good amount because of the HDDs. I switched the NAS off every evening I do not have a real backup of the data on the NAS, only the internal raid 1 as safety. I really dont want to loose my source trees under no circumstances, so I would really be sleeping better if I knew I had regular backups somewhere. Recently, the board seemed to have died, I can't boot anymore. Thus, I was thinking about a redesign of my NAS (I still have to find out what parts are broken, I probably need to replace the mainboard and SSD. HDDs seem to be okay). First of all, I was wondering what other users have as backup for their NAS? Are you actually using a second NAS, and regularly copying over the data to have it safe? Or is there any better solution to this? I was thinking about getting a cheap NAS like the synology DS112j with only one disk, and use rsync or something similar to regularly copy data over to the second NAS (wake the second NAS upon start, shut it down after copy). Although this approach seems somewhat weird, It would have the benefit (?) that I could use a single disk instead of raid in the main NAS, and put the disk asleep when idle, and have the NAS running 24/7 with low energy consumption (I found no way to do this with a gmirror setup). Is there any recommended backup solution for a small NAS? Then I was thinking about a different raid setup. Since I have to buy a new mainboard as well as SSD, I might as well switch over to a i3 board with more ram, and also switch to ZFS. I am not familar with ZFS, I've never used it, but I read and hear much about it. Would it be viable to set up a ZFS storage with only 2 disks? Can I easily extend this storage with more disks, once I choose to add some? I could maybe get a new case like the Fractal Design Array R2 which has more 3,5" slots. I could as well get another 2 disks, but I would prefer sticking with the existing 2 for enegery/heat/noise reasons. Should I go for a ZFS storage or stick to my gmirror setup? I would also like to keep freebsd as operating system, and also I dont need any web gui or something (that is, I dont need/want to use FreeNAS or Openfiler etc). Does anyone maybe have a sample setup in use so I can compare energy consumption/noise/software setup? Any guidance towards the NAS of my dreams (silent, low energy, safe w/ backups) much appreciated.

    Read the article

  • Monitor your Hard Drive’s Health with Acronis Drive Monitor

    - by Matthew Guay
    Are you worried that your computer’s hard drive could die without any warning?  Here’s how you can keep tabs on it and get the first warning signs of potential problems before you actually lose your critical data. Hard drive failures are one of the most common ways people lose important data from their computers.  As more of our memories and important documents are stored digitally, a hard drive failure can mean the loss of years of work.  Acronis Drive Monitor helps you avert these disasters by warning you at the first signs your hard drive may be having trouble.  It monitors many indicators, including heat, read/write errors, total lifespan, and more. It then notifies you via a taskbar popup or email that problems have been detected.  This early warning lets you know ahead of time that you may need to purchase a new hard drive and migrate your data before it’s too late. Getting Started Head over to the Acronis site to download Drive Monitor (link below).  You’ll need to enter your name and email, and then you can download this free tool. Also, note that the download page may ask if you want to include a trial of their for-pay backup program.  If you wish to simply install the Drive Monitor utility, click Continue without adding. Run the installer when the download is finished.  Follow the prompts and install as normal. Once it’s installed, you can quickly get an overview of your hard drives’ health.  Note that it shows 3 categories: Disk problems, Acronis backup, and Critical Events.  On our computer, we had Seagate DiskWizard, an image backup utility based on Acronis Backup, installed, and Acronis detected it. Drive Monitor stays running in your tray even when the application window is closed.  It will keep monitoring your hard drives, and will alert you if there’s a problem. Find Detailed Information About Your Hard Drives Acronis’ simple interface lets you quickly see an overview of how the drives on your computer are performing.  If you’d like more information, click the link under the description.  Here we see that one of our drives have overheated, so click Show disks to get more information. Now you can select each of your drives and see more information about them.  From the Disk overview tab that opens by default, we see that our drive is being monitored, has been running for a total of 368 days, and that it’s health is good.  However, it is running at 113F, which is over the recommended max of 107F.   The S.M.A.R.T. parameters tab gives us more detailed information about our drive.  Most users wouldn’t know what an accepted value would be, so it also shows the status.  If the value is within the accepted parameters, it will report OK; otherwise, it will show that has a problem in this area. One very interesting piece of information we can see is the total number of Power-On Hours, Start/Stop Count, and Power Cycle Count.  These could be useful indicators to check if you’re considering purchasing a second hand computer.  Simply load this program, and you’ll get a better view of how long it’s been in use. Finally, the Events tab shows each time the program gave a warning.  We can see that our drive, which had been acting flaky already, is routinely overheating even when our other hard drive was running in normal temperature ranges. Monitor Acronis Backups And Critical Errors In addition to monitoring critical stats of your hard drives, Acronis Drive Monitor also keeps up with the status of your backup software and critical events reported by Windows.  You can access these from the front page, or via the links on the left hand sidebar.  If you have any edition of any Acronis Backup product installed, it will show that it was detected.  Note that it can only monitor the backup status of the newest versions of Acronis Backup and True Image. If no Acronis backup software was installed, it will show a warning that the drive may be unprotected and will give you a link to download Acronis backup software.   If you have another backup utility installed that you wish to monitor yourself, click Configure backup monitoring, and then disable monitoring on the drives you’re monitoring yourself. Finally, you can view any detected Critical events from the Critical events tab on the left. Get Emailed When There’s a Problem One of Drive Monitor’s best features is the ability to send you an email whenever there’s a problem.  Since this program can run on any version of Windows, including the Server and Home Server editions, you can use this feature to stay on top of your hard drives’ health even when you’re not nearby.  To set this up, click Options in the top left corner. Select Alerts on the left, and then click the Change settings link to setup your email account. Enter the email address which you wish to receive alerts, and a name for the program.  Then, enter the outgoing mail server settings for your email.  If you have a Gmail account, enter the following information: Outgoing mail server (SMTP): smtp.gmail.com Port: 587 Username and Password: Your gmail address and password Check the Use encryption box, and then select TLS from the encryption options.   It will now send a test message to your email account, so check and make sure it sent ok. Now you can choose to have the program automatically email you when warnings and critical alerts appear, and also to have it send regular disk status reports.   Conclusion Whether you’ve got a brand new hard drive or one that’s seen better days, knowing the real health of your it is one of the best ways to be prepared before disaster strikes.  It’s no substitute for regular backups, but can help you avert problems.  Acronis Drive Monitor is a nice tool for this, and although we wish it wasn’t so centered around their backup offerings, we still found it a nice tool. Link Download Acronis Drive Monitor (registration required) Similar Articles Productive Geek Tips Quick Tip: Change Monitor Timeout From Command LineAnalyze and Manage Hard Drive Space with WinDirStatMonitor CPU, Memory, and Disk IO In Windows 7 with Taskbar MetersDefrag Multiple Hard Drives At Once In WindowsFind Your Missing USB Drive on Windows XP TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips HippoRemote Pro 2.2 Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Windows 7’s WordPad is Actually Good Greate Image Viewing and Management with Zoner Photo Studio Free Windows Media Player Plus! – Cool WMP Enhancer Get Your Team’s World Cup Schedule In Google Calendar Backup Drivers With Driver Magician TubeSort: YouTube Playlist Organizer

    Read the article

  • SQL SERVER – Faster SQL Server Databases and Applications – Power and Control with SafePeak Caching Options

    - by Pinal Dave
    Update: This blog post is written based on the SafePeak, which is available for free download. Today, I’d like to examine more closely one of my preferred technologies for accelerating SQL Server databases, SafePeak. Safepeak’s software provides a variety of advanced data caching options, techniques and tools to accelerate the performance and scalability of SQL Server databases and applications. I’d like to look more closely at some of these options, as some of these capabilities could help you address lagging database and performance on your systems. To better understand the available options, it is best to start by understanding the difference between the usual “Basic Caching” vs. SafePeak’s “Dynamic Caching”. Basic Caching Basic Caching (or the stale and static cache) is an ability to put the results from a query into cache for a certain period of time. It is based on TTL, or Time-to-live, and is designed to stay in cache no matter what happens to the data. For example, although the actual data can be modified due to DML commands (update/insert/delete), the cache will still hold the same obsolete query data. Meaning that with the Basic Caching is really static / stale cache.  As you can tell, this approach has its limitations. Dynamic Caching Dynamic Caching (or the non-stale cache) is an ability to put the results from a query into cache while maintaining the cache transaction awareness looking for possible data modifications. The modifications can come as a result of: DML commands (update/insert/delete), indirect modifications due to triggers on other tables, executions of stored procedures with internal DML commands complex cases of stored procedures with multiple levels of internal stored procedures logic. When data modification commands arrive, the caching system identifies the related cache items and evicts them from cache immediately. In the dynamic caching option the TTL setting still exists, although its importance is reduced, since the main factor for cache invalidation (or cache eviction) become the actual data updates commands. Now that we have a basic understanding of the differences between “basic” and “dynamic” caching, let’s dive in deeper. SafePeak: A comprehensive and versatile caching platform SafePeak comes with a wide range of caching options. Some of SafePeak’s caching options are automated, while others require manual configuration. Together they provide a complete solution for IT and Data managers to reach excellent performance acceleration and application scalability for  a wide range of business cases and applications. Automated caching of SQL Queries: Fully/semi-automated caching of all “read” SQL queries, containing any types of data, including Blobs, XMLs, Texts as well as all other standard data types. SafePeak automatically analyzes the incoming queries, categorizes them into SQL Patterns, identifying directly and indirectly accessed tables, views, functions and stored procedures; Automated caching of Stored Procedures: Fully or semi-automated caching of all read” stored procedures, including procedures with complex sub-procedure logic as well as procedures with complex dynamic SQL code. All procedures are analyzed in advance by SafePeak’s  Metadata-Learning process, their SQL schemas are parsed – resulting with a full understanding of the underlying code, objects dependencies (tables, views, functions, sub-procedures) enabling automated or semi-automated (manually review and activate by a mouse-click) cache activation, with full understanding of the transaction logic for cache real-time invalidation; Transaction aware cache: Automated cache awareness for SQL transactions (SQL and in-procs); Dynamic SQL Caching: Procedures with dynamic SQL are pre-parsed, enabling easy cache configuration, eliminating SQL Server load for parsing time and delivering high response time value even in most complicated use-cases; Fully Automated Caching: SQL Patterns (including SQL queries and stored procedures) that are categorized by SafePeak as “read and deterministic” are automatically activated for caching; Semi-Automated Caching: SQL Patterns categorized as “Read and Non deterministic” are patterns of SQL queries and stored procedures that contain reference to non-deterministic functions, like getdate(). Such SQL Patterns are reviewed by the SafePeak administrator and in usually most of them are activated manually for caching (point and click activation); Fully Dynamic Caching: Automated detection of all dependent tables in each SQL Pattern, with automated real-time eviction of the relevant cache items in the event of “write” commands (a DML or a stored procedure) to one of relevant tables. A default setting; Semi Dynamic Caching: A manual cache configuration option enabling reducing the sensitivity of specific SQL Patterns to “write” commands to certain tables/views. An optimization technique relevant for cases when the query data is either known to be static (like archive order details), or when the application sensitivity to fresh data is not critical and can be stale for short period of time (gaining better performance and reduced load); Scheduled Cache Eviction: A manual cache configuration option enabling scheduling SQL Pattern cache eviction based on certain time(s) during a day. A very useful optimization technique when (for example) certain SQL Patterns can be cached but are time sensitive. Example: “select customers that today is their birthday”, an SQL with getdate() function, which can and should be cached, but the data stays relevant only until 00:00 (midnight); Parsing Exceptions Management: Stored procedures that were not fully parsed by SafePeak (due to too complex dynamic SQL or unfamiliar syntax), are signed as “Dynamic Objects” with highest transaction safety settings (such as: Full global cache eviction, DDL Check = lock cache and check for schema changes, and more). The SafePeak solution points the user to the Dynamic Objects that are important for cache effectiveness, provides easy configuration interface, allowing you to improve cache hits and reduce cache global evictions. Usually this is the first configuration in a deployment; Overriding Settings of Stored Procedures: Override the settings of stored procedures (or other object types) for cache optimization. For example, in case a stored procedure SP1 has an “insert” into table T1, it will not be allowed to be cached. However, it is possible that T1 is just a “logging or instrumentation” table left by developers. By overriding the settings a user can allow caching of the problematic stored procedure; Advanced Cache Warm-Up: Creating an XML-based list of queries and stored procedure (with lists of parameters) for periodically automated pre-fetching and caching. An advanced tool allowing you to handle more rare but very performance sensitive queries pre-fetch them into cache allowing high performance for users’ data access; Configuration Driven by Deep SQL Analytics: All SQL queries are continuously logged and analyzed, providing users with deep SQL Analytics and Performance Monitoring. Reduce troubleshooting from days to minutes with database objects and SQL Patterns heat-map. The performance driven configuration helps you to focus on the most important settings that bring you the highest performance gains. Use of SafePeak SQL Analytics allows continuous performance monitoring and analysis, easy identification of bottlenecks of both real-time and historical data; Cloud Ready: Available for instant deployment on Amazon Web Services (AWS). As you can see, there are many options to configure SafePeak’s SQL Server database and application acceleration caching technology to best fit a lot of situations. If you’re not familiar with their technology, they offer free-trial software you can download that comes with a free “help session” to help get you started. You can access the free trial here. Also, SafePeak is available to use on Amazon Cloud. Reference: Pinal Dave (http://blog.sqlauthority.com)Filed under: PostADay, SQL, SQL Authority, SQL Performance, SQL Query, SQL Server, SQL Tips and Tricks, T SQL

    Read the article

  • How can I keep the cpu temp low?

    - by Newton
    I have an HP pavilion dv7, I'm using ubuntu 12.04 so the overheating problem with sandybridge cpu is a lot better. However my laptop is still becoming too hot to keep on my legs. The problem is that the fan wait too much before starting, so the medium temp is too hight. When I'm using windows 7 the laptop is room-temperature cold, I've absolutely no problem. On windows the fan is always spinning very low & very silently so the heat is continuously removed, without reaching an unconfortable temp. How can I force the computer to act like that also on ubuntu? PS The bios can't let me control this kind of thing, and this is my experience with lm-sensors and fancontrol al@notebook:~$ sudo sensors-detect [sudo] password for al: # sensors-detect revision 5984 (2011-07-10 21:22:53 +0200) # System: Hewlett-Packard HP Pavilion dv7 Notebook PC (laptop) # Board: Hewlett-Packard 1800 This program will help you determine which kernel modules you need to load to use lm_sensors most effectively. It is generally safe and recommended to accept the default answers to all questions, unless you know what you're doing. Some south bridges, CPUs or memory controllers contain embedded sensors. Do you want to scan for them? This is totally safe. (YES/no): y Module cpuid loaded successfully. Silicon Integrated Systems SIS5595... No VIA VT82C686 Integrated Sensors... No VIA VT8231 Integrated Sensors... No AMD K8 thermal sensors... No AMD Family 10h thermal sensors... No AMD Family 11h thermal sensors... No AMD Family 12h and 14h thermal sensors... No AMD Family 15h thermal sensors... No AMD Family 15h power sensors... No Intel digital thermal sensor... Success! (driver `coretemp') Intel AMB FB-DIMM thermal sensor... No VIA C7 thermal sensor... No VIA Nano thermal sensor... No Some Super I/O chips contain embedded sensors. We have to write to standard I/O ports to probe them. This is usually safe. Do you want to scan for Super I/O sensors? (YES/no): y Probing for Super-I/O at 0x2e/0x2f Trying family `National Semiconductor/ITE'... No Trying family `SMSC'... No Trying family `VIA/Winbond/Nuvoton/Fintek'... No Trying family `ITE'... No Probing for Super-I/O at 0x4e/0x4f Trying family `National Semiconductor/ITE'... Yes Found unknown chip with ID 0x8518 Some hardware monitoring chips are accessible through the ISA I/O ports. We have to write to arbitrary I/O ports to probe them. This is usually safe though. Yes, you do have ISA I/O ports even if you do not have any ISA slots! Do you want to scan the ISA I/O ports? (YES/no): y Probing for `National Semiconductor LM78' at 0x290... No Probing for `National Semiconductor LM79' at 0x290... No Probing for `Winbond W83781D' at 0x290... No Probing for `Winbond W83782D' at 0x290... No Lastly, we can probe the I2C/SMBus adapters for connected hardware monitoring devices. This is the most risky part, and while it works reasonably well on most systems, it has been reported to cause trouble on some systems. Do you want to probe the I2C/SMBus adapters now? (YES/no): y Using driver `i2c-i801' for device 0000:00:1f.3: Intel Cougar Point (PCH) Module i2c-i801 loaded successfully. Module i2c-dev loaded successfully. Next adapter: i915 gmbus disabled (i2c-0) Do you want to scan it? (YES/no/selectively): y Next adapter: i915 gmbus ssc (i2c-1) Do you want to scan it? (YES/no/selectively): y Next adapter: i915 GPIOB (i2c-2) Do you want to scan it? (YES/no/selectively): y Next adapter: i915 gmbus vga (i2c-3) Do you want to scan it? (YES/no/selectively): y Next adapter: i915 GPIOA (i2c-4) Do you want to scan it? (YES/no/selectively): y Next adapter: i915 gmbus panel (i2c-5) Do you want to scan it? (YES/no/selectively): y Client found at address 0x50 Probing for `Analog Devices ADM1033'... No Probing for `Analog Devices ADM1034'... No Probing for `SPD EEPROM'... No Probing for `EDID EEPROM'... Yes (confidence 8, not a hardware monitoring chip) Next adapter: i915 GPIOC (i2c-6) Do you want to scan it? (YES/no/selectively): y Client found at address 0x50 Probing for `Analog Devices ADM1033'... No Probing for `Analog Devices ADM1034'... No Probing for `SPD EEPROM'... No Probing for `EDID EEPROM'... Yes (confidence 8, not a hardware monitoring chip) Next adapter: i915 gmbus dpc (i2c-7) Do you want to scan it? (YES/no/selectively): y Next adapter: i915 GPIOD (i2c-8) Do you want to scan it? (YES/no/selectively): y Next adapter: i915 gmbus dpb (i2c-9) Do you want to scan it? (YES/no/selectively): y Next adapter: i915 GPIOE (i2c-10) Do you want to scan it? (YES/no/selectively): y Next adapter: i915 gmbus reserved (i2c-11) Do you want to scan it? (YES/no/selectively): y Next adapter: i915 gmbus dpd (i2c-12) Do you want to scan it? (YES/no/selectively): y Next adapter: i915 GPIOF (i2c-13) Do you want to scan it? (YES/no/selectively): y Next adapter: DPDDC-B (i2c-14) Do you want to scan it? (YES/no/selectively): y Now follows a summary of the probes I have just done. Just press ENTER to continue: Driver `coretemp': * Chip `Intel digital thermal sensor' (confidence: 9) To load everything that is needed, add this to /etc/modules: #----cut here---- # Chip drivers coretemp #----cut here---- If you have some drivers built into your kernel, the list above will contain too many modules. Skip the appropriate ones! Do you want to add these lines automatically to /etc/modules? (yes/NO)y Successful! Monitoring programs won't work until the needed modules are loaded. You may want to run 'service module-init-tools start' to load them. Unloading i2c-dev... OK Unloading i2c-i801... OK Unloading cpuid... OK al@notebook:~$ sudo /etc/init.d/module-init-tools restart Rather than invoking init scripts through /etc/init.d, use the service(8) utility, e.g. service module-init-tools restart Since the script you are attempting to invoke has been converted to an Upstart job, you may also use the stop(8) and then start(8) utilities, e.g. stop module-init-tools ; start module-init-tools. The restart(8) utility is also available. module-init-tools stop/waiting al@notebook:~$ sudo service module-init-tools restart stop: Unknown instance: module-init-tools stop/waiting al@notebook:~$ sudo service module-init-tools start module-init-tools stop/waiting al@notebook:~$ sudo pwmconfig # pwmconfig revision 5857 (2010-08-22) This program will search your sensors for pulse width modulation (pwm) controls, and test each one to see if it controls a fan on your motherboard. Note that many motherboards do not have pwm circuitry installed, even if your sensor chip supports pwm. We will attempt to briefly stop each fan using the pwm controls. The program will attempt to restore each fan to full speed after testing. However, it is ** very important ** that you physically verify that the fans have been to full speed after the program has completed. /usr/sbin/pwmconfig: There are no pwm-capable sensor modules installed Is my case too desperate?

    Read the article

  • Cost Comparison Hard Disk Drive to Solid State Drive on Price per Gigabyte - dispelling a myth!

    - by tonyrogerson
    It is often said that Hard Disk Drive storage is significantly cheaper per GiByte than Solid State Devices – this is wholly inaccurate within the database space. People need to look at the cost of the complete solution and not just a single component part in isolation to what is really required to meet the business requirement. Buying a single Hitachi Ultrastar 600GB 3.5” SAS 15Krpm hard disk drive will cost approximately £239.60 (http://scan.co.uk, 22nd March 2012) compared to an OCZ 600GB Z-Drive R4 CM84 PCIe costing £2,316.54 (http://scan.co.uk, 22nd March 2012); I’ve not included FusionIO ioDrive because there is no public pricing available for it – something I never understand and personally when companies do this I immediately think what are they hiding, luckily in FusionIO’s case the product is proven though is expensive compared to OCZ enterprise offerings. On the face of it the single 15Krpm hard disk has a price per GB of £0.39, the SSD £3.86; this is what you will see in the press and this is what sales people will use in comparing the two technologies – do not be fooled by this bullshit people! What is the requirement? The requirement is the database will have a static size of 400GB kept static through archiving so growth and trim will balance the database size, the client requires resilience, there will be several hundred call centre staff querying the database where queries will read a small amount of data but there will be no hot spot in the data so the randomness will come across the entire 400GB of the database, estimates predict that the IOps required will be approximately 4,000IOps at peak times, because it’s a call centre system the IO latency is important and must remain below 5ms per IO. The balance between read and write is 70% read, 30% write. The requirement is now defined and we have three of the most important pieces of the puzzle – space required, estimated IOps and maximum latency per IO. Something to consider with regard SQL Server; write activity requires synchronous IO to the storage media specifically the transaction log; that means the write thread will wait until the IO is completed and hardened off until the thread can continue execution, the requirement has stated that 30% of the system activity will be write so we can expect a high amount of synchronous activity. The hardware solution needs to be defined; two possible solutions: hard disk or solid state based; the real question now is how many hard disks are required to achieve the IO throughput, the latency and resilience, ditto for the solid state. Hard Drive solution On a test on an HP DL380, P410i controller using IOMeter against a single 15Krpm 146GB SAS drive, the throughput given on a transfer size of 8KiB against a 40GiB file on a freshly formatted disk where the partition is the only partition on the disk thus the 40GiB file is on the outer edge of the drive so more sectors can be read before head movement is required: For 100% sequential IO at a queue depth of 16 with 8 worker threads 43,537 IOps at an average latency of 2.93ms (340 MiB/s), for 100% random IO at the same queue depth and worker threads 3,733 IOps at an average latency of 34.06ms (34 MiB/s). The same test was done on the same disk but the test file was 130GiB: For 100% sequential IO at a queue depth of 16 with 8 worker threads 43,537 IOps at an average latency of 2.93ms (340 MiB/s), for 100% random IO at the same queue depth and worker threads 528 IOps at an average latency of 217.49ms (4 MiB/s). From the result it is clear random performance gets worse as the disk fills up – I’m currently writing an article on short stroking which will cover this in detail. Given the work load is random in nature looking at the random performance of the single drive when only 40 GiB of the 146 GB is used gives near the IOps required but the latency is way out. Luckily I have tested 6 x 15Krpm 146GB SAS 15Krpm drives in a RAID 0 using the same test methodology, for the same test above on a 130 GiB for each drive added the performance boost is near linear, for each drive added throughput goes up by 5 MiB/sec, IOps by 700 IOps and latency reducing nearly 50% per drive added (172 ms, 94 ms, 65 ms, 47 ms, 37 ms, 30 ms). This is because the same 130GiB is spread out more as you add drives 130 / 1, 130 / 2, 130 / 3 etc. so implicit short stroking is occurring because there is less file on each drive so less head movement required. The best latency is still 30 ms but we have the IOps required now, but that’s on a 130GiB file and not the 400GiB we need. Some reality check here: a) the drive randomness is more likely to be 50/50 and not a full 100% but the above has highlighted the effect randomness has on the drive and the more a drive fills with data the worse the effect. For argument sake let us assume that for the given workload we need 8 disks to do the job, for resilience reasons we will need 16 because we need to RAID 1+0 them in order to get the throughput and the resilience, RAID 5 would degrade performance. Cost for hard drives: 16 x £239.60 = £3,833.60 For the hard drives we will need disk controllers and a separate external disk array because the likelihood is that the server itself won’t take the drives, a quick spec off DELL for a PowerVault MD1220 which gives the dual pathing with 16 disks 146GB 15Krpm 2.5” disks is priced at £7,438.00, note its probably more once we had two controller cards to sit in the server in, racking etc. Minimum cost taking the DELL quote as an example is therefore: {Cost of Hardware} / {Storage Required} £7,438.60 / 400 = £18.595 per GB £18.59 per GiB is a far cry from the £0.39 we had been told by the salesman and the myth. Yes, the storage array is composed of 16 x 146 disks in RAID 10 (therefore 8 usable) giving an effective usable storage availability of 1168GB but the actual storage requirement is only 400 and the extra disks have had to be purchased to get the  IOps up. Solid State Drive solution A single card significantly exceeds the IOps and latency required, for resilience two will be required. ( £2,316.54 * 2 ) / 400 = £11.58 per GB With the SSD solution only two PCIe sockets are required, no external disk units, no additional controllers, no redundant controllers etc. Conclusion I hope by showing you an example that the myth that hard disk drives are cheaper per GiB than Solid State has now been dispelled - £11.58 per GB for SSD compared to £18.59 for Hard Disk. I’ve not even touched on the running costs, compare the costs of running 18 hard disks, that’s a lot of heat and power compared to two PCIe cards!Just a quick note: I've left a fair amount of information out due to this being a blog! If in doubt, email me :)I'll also deal with the myth that SSD's wear out at a later date as well - that's just way over done still, yes, 5 years ago, but now - no.

    Read the article

  • The Great Divorce

    - by BlackRabbitCoder
    I have a confession to make: I've been in an abusive relationship for more than 17 years now.  Yes, I am not ashamed to admit it, but I'm finally doing something about it. I met her in college, she was new and sexy and amazingly fast -- and I'd never met anything like her before.  Her style and her power captivated me and I couldn't wait to learn more about her.  I took a chance on her, and though I learned a lot from her -- and will always be grateful for my time with her -- I think it's time to move on. Her name was C++, and she so outshone my previous love, C, that any thoughts of going back evaporated in the heat of this new romance.  She promised me she'd be gentle and not hurt me the way C did.  She promised me she'd clean-up after herself better than C did.  She promised me she'd be less enigmatic and easier to keep happy than C was.  But I was deceived.  Oh sure, as far as truth goes, it wasn't a complete lie.  To some extent she was more fun, more powerful, safer, and easier to maintain.  But it just wasn't good enough -- or at least it's not good enough now. I loved C++, some part of me still does, it's my first-love of programming languages and I recognize its raw power, its blazing speed, and its improvements over its predecessor.  But with today's hardware, at speeds we could only dream to conceive of twenty years ago, that need for speed -- at the cost of all else -- has died, and that has left my feelings for C++ moribund. If I ever need to write an operating system or a device driver, then I might need that speed.  But 99% of the time I don't.  I'm a business-type programmer and chances are 90% of you are too, and even the ones who need speed at all costs may be surprised by how much you sacrifice for that.   That's not to say that I don't want my software to perform, and it's not to say that in the business world we don't care about speed or that our job is somehow less difficult or technical.  There's many times we write programs to handle millions of real-time updates or handle thousands of financial transactions or tracking trading algorithms where every second counts.  But if I choose to write my code in C++ purely for speed chances are I'll never notice the speed increase -- and equally true chances are it will be far more prone to crash and far less easy to maintain.  Nearly without fail, it's the macro-optimizations you need, not the micro-optimizations.  If I choose to write a O(n2) algorithm when I could have used a O(n) algorithm -- that can kill me.  If I choose to go to the database to load a piece of unchanging data every time instead of caching it on first load -- that too can kill me.  And if I cross the network multiple times for pieces of data instead of getting it all at once -- yes that can also kill me.  But choosing an overly powerful and dangerous mid-level language to squeeze out every last drop of performance will realistically not make stock orders process any faster, and more likely than not open up the system to more risk of crashes and resource leaks. And that's when my love for C++ began to die.  When I noticed that I didn't need that speed anymore.  That that speed was really kind of a lie.  Sure, I can be super efficient and pack bits in a byte instead of using separate boolean values.  Sure, I can use an unsigned char instead of an int.  But in the grand scheme of things it doesn't matter as much as you think it does.  The key is maintainability, and that's where C++ failed me.  I like to tell the other developers I work with that there's two levels of correctness in coding: Is it immediately correct? Will it stay correct? That is, you can hack together any piece of code and make it correct to satisfy a task at hand, but if a new developer can't come in tomorrow and make a fairly significant change to it without jeopardizing that correctness, it won't stay correct. Some people laugh at me when I say I now prefer maintainability over speed.  But that is exactly the point.  If you focus solely on speed you tend to produce code that is much harder to maintain over the long hall, and that's a load of technical debt most shops can't afford to carry and end up completely scrapping code before it's time.  When good code is written well for maintainability, though, it can be correct both now and in the future. And you know the best part is?  My new love is nearly as fast as C++, and in some cases even faster -- and better than that, I know C# will treat me right.  Her creators have poured hundreds of thousands of hours of time into making her the sexy beast she is today.  They made her easy to understand and not an enigmatic mess.  They made her consistent and not moody and amorphous.  And they made her perform as fast as I care to go by optimizing her both at compile time and a run-time. Her code is so elegant and easy on the eyes that I'm not worried where she will run to or what she'll pull behind my back.  She is powerful enough to handle all my tasks, fast enough to execute them with blazing speed, maintainable enough so that I can rely on even fairly new peers to modify my work, and rich enough to allow me to satisfy any need.  C# doesn't ask me to clean up her messes!  She cleans up after herself and she tries to make my life easier for me by taking on most of those optimization tasks C++ asked me to take upon myself.  Now, there are many of you who would say that I am the cause of my own grief, that it was my fault C++ didn't behave because I didn't pay enough attention to her.  That I alone caused the pain she inflicted on me.  And to some extent, you have a point.  But she was so high maintenance, requiring me to know every twist and turn of her vast and unrestrained power that any wrong term or bout of forgetfulness was met with painful reminders that she wasn't going to watch my back when I made a mistake.  But C#, she loves me when I'm good, and she loves me when I'm bad, and together we make beautiful code that is both fast and safe. So that's why I'm leaving C++ behind.  She says she's changing for me, but I have no interest in what C++0x may bring.  Oh, I'll still keep in touch, and maybe I'll see her now and again when she brings her problems to my door and asks for some attention -- for I always have a soft spot for her, you see.  But she's out of my house now.  I have three kids and a dog and a cat, and all require me to clean up after them, why should I have to clean up after my programming language as well?

    Read the article

  • 10 tape technology features that make you go hmm.

    - by Karoly Vegh
    A week ago an Oracle/StorageTek Tape Specialist, Christian Vanden Balck, visited Vienna, and agreed to visit customers to do techtalks and update them about the technology boom going around tape. I had the privilege to attend some of his sessions and noted the information and features that took the customers by surprise and made them think. Allow me to share the top 10: I. StorageTek as a brand: StorageTek is one of he strongest names in the Tape field. The brand itself was valued so much by customers that even after Sun Microsystems acquiring StorageTek and the Oracle acquiring Sun the brand lives on with all the Oracle tapelibraries are officially branded StorageTek.See http://www.oracle.com/us/products/servers-storage/storage/tape-storage/overview/index.html II. Disk information density limitations: Disk technology struggles with information density. You haven't seen the disk sizes exploding lately, have you? That's partly because there are physical limits on a disk platter. The size is given, the number of platters is limited, they just can't grow, and are running out of physical area to write to. Now, in a T10000C tape cartridge we have over 1000m long tape. There you go, you have got your physical space and don't need to stuff all that data crammed together. You can write in a reliable pattern, and have space to grow too. III. Oracle has a market share of 62% worldwide in recording head manufacturing. That's right. If you are running LTO drives, with a good chance you rely on StorageTek production. That's two out of three LTO recording heads produced worldwide.  IV. You can store 1 Exabyte data in a single tape library. Yes, an Exabyte. That is 1000 Petabytes. Or, a million Terabytes. A thousand million GigaBytes. You can store that in a stacked StorageTek SL8500 tapelibrary. In one SL8500 you can put 10.000 T10000C cartridges, that store 10TB data (compressed). You can stack 10 of these SL8500s together. Boom. 1000.000 TB.(n.b.: stacking means interconnecting the libraries. Yes, cartridges are moved between the stacked libraries automatically.)  V. EMC: 'Tape doesn't suck after all. We moved on.': Do you remember the infamous 'Tape sucks, move on' Datadomain slogan? Of course they had to put it that way, having only had disk products. But here's a fun fact: on the EMCWorld 2012 there was a major presence of a Tape-tech company - EMC, in a sudden burst of sanity is embracing tape again. VI. The miraculous T10000C: Oracle StorageTek has developed an enterprise-grade tapedrive and cartridge, the T10000C. With awesome numbers: The Cartridge: Native 5TB capacity, 10TB with compression Over a kilometer long tape within the cartridge. And it's locked when unmounted, no rattling of your data.  Replaced the metalparticles datalayer with BaFe (bariumferrite) - metalparticles lose around 7% of magnetism within 30 days. BaFe does not. Yes we employ solid-state physicists doing R&D on demagnetisation in our labs. Can be partitioned, storage tiering within the cartridge!  The Drive: 2GB Cache Encryption implemented in HW - no performance hit 252 MB/s native sustained data rate, beats disk technology by far. Not to mention peak throughput.  Leading the tape while never touching the data side of it, protecting your data physically too Data integritiy checking (CRC recalculation) on tape within the drive without having to read it back to the server reordering data from tape-order, delivering it back in application-order  writing 32 tracks at once, reading them back for CRC check at once VII. You only use 20% of your data on a regular basis. The rest 80% is just lying around for years. On continuously spinning disks. Doubly consuming energy (power+cooling), blocking diskstorage capacity. There is a solution called SAM (Storage Archive Manager) that provides you a filesystem unifying disk and tape, moving data on-demand and for clients transparently between the different storage tiers. You can share these filesystems with NFS or CIFS for clients, and enjoy the low TCO of tape. Tapes don't spin. They sit quietly in their slots, storing 10TB data, using no energy, producing no heat, automounted when a client accesses their data.See: http://www.oracle.com/us/products/servers-storage/storage/storage-software/storage-archive-manager/overview/index.html VIII. HW supported for three decades: Did you know that the original PowderHorn library was released in '87 and has been only discontinued in 2010? That is over two decades of supported operation. Tape libraries are - just like the data carrying on tapecartridges - built for longevity. Oh, and the T10000C cartridge has 30-year archival life for long-term retention.  IX. Tape is easy to manage: Have you heard of Tape Storage Analytics? It is a central graphical tool to summarize, monitor, analyze dataflow, health and performance of drives and libraries, see: http://www.oracle.com/us/products/servers-storage/storage/tape-storage/tape-analytics/overview/index.html X. The next generation: The T10000B drives were able to reuse the T10000A cartridges and write on them even more data. On the same cartridges. We call this investment protection, and this is very important for Oracle for the future too. We usually support two generations of cartridges together. The current drive is a T10000C. (...I know I promised to enlist 10, but I got still two more I really want to mention. Allow me to work around the problem: ) X++. The TallBots, the robots moving around the cartridges in the StorageTek library from tapeslots to the drives are cableless. Cables, belts, chains running to moving parts in a library cause maintenance downtimes. So StorageTek eliminated them. The TallBots get power, commands, even firmwareupgrades through the rails they are running on. Also, the TallBots don't just hook'n'pull the tapes out of their slots, they actually grip'n'lift them out. No friction, no scratches, no zillion little plastic particles floating around in the library, in the drives, on your data. (X++)++: Tape beats SSDs and Disks. In terms of throughput (252 MB/s), in terms of TCO: disks cause around 290x more power and cooling, in terms of capacity: 10TB on a single media and soon more.  So... do you need to store large amounts of data? Are you legally bound to archive it for dozens of years? Would you benefit from automatic storage tiering? Have you got large mediachunks to be streamed at times? Have you got power and cooling issues in the growing datacenters? Do you find EMC's 180° turn of tape attitude interesting, but appreciate it at the same time? With all that, you aren't alone. The most data on this planet is stored on tape. Tape is coming. Big time.

    Read the article

  • Reviewing Retail Predictions for 2011

    - by David Dorf
    Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} I've been busy thinking about what 2012 and beyond will look like for retail, and I have some interesting predictions to share.  But before I go there, let’s first review this year’s predictions before making new ones for 2012. 1. Alternate Payments We've seen several alternate payment schemes emerge over the last two years, and 2011 may be the year one of them takes hold. Any competition that can drive down fees will be good for everyone. I'm betting that Apple will add NFC chips to their next version of the iPhone, then enable payments in stores using iTunes accounts on the backend. Paypal will continue to make inroads, and Isis will announce a pilot. The iPhone 4S did not contain an NFC chip, so we’ll have to continuing waiting for the iPhone 5. PayPal announced its moving into in-store payments, and Google launched its wallet in selected cities.  Overall I think the payment scene is heating up and that trend will continue. 2. Engineered Systems The industry is moving toward purpose-built appliances that are optimized across the entire stack. Oracle calls these "engineered systems" and the first two examples are Exadata and Exalogic, but there are other examples from other vendors. These are particularly important to the retail industry because of the volume of data that must be processed. There should be continued adoption in 2011. Oracle reports that Exadata is its fasting growing product, and at the recent OpenWorld it announced the SuperCluster and Exalytics products, both continuing the engineered systems trend. SAP’s HANA continues to receive attention, and IBM also seems to be moving in this direction. 3. Social Analytics There are lots of tools that provide insight into how a brand is perceived across popular internet sites, but as far as I know, these tools are not industry specific. The next step needs to mine the data and determine how it should influence retail operations. The data needs to help retailers determine how they create promotions, which products to stock, and how to keep consumers engaged. Social data alone does not provide the answers, but its one more data point that will help retailers make better decisions. Look for some vendor consolidation to help make this happen. In March, Salesforce.com acquired leading social monitoring vendor Radian6 and followed up with acquisitions of Heroku and Model Metrics. The notion of Social CRM seems to be going more mainstream now. 4. 2-D Barcodes Look for more QRCodes on shelf-tags, in newspaper circulars, and on billboards. It's a great portal from the physical world into the digital one that buys us time until augmented reality matures further. Nobody wants to type "www", backslash, and ".com" on their phones. QRCodes are everywhere. ‘Nuff said. 5. In the words of Microsoft, "To the Cloud!" My favorite "cloud application" is Evernote. If you take notes on your work laptop, you will inevitably need those notes on your home PC. And if you manage to solve that problem, you'll need to access them from your mobile phone. Evernote stores your notes in the cloud and provides easy ways to access them. Being able to access a service from anywhere and not having to worry about backups, upgrades, etc. is great. Retailers will start to rely on cloud services, both public and private, in the coming year. There were no shortage of announcements in this area: Amazon’s cloud-based Kindle Fire, Apple’s iCloud, Oracle’s Public Cloud, etc. I saw an interesting presentation showing how BevMo moved their systems to the cloud.  Seems like retailers are starting to consider the cloud for specific uses. 6. F-CommerceTop of Form Move over "E" and "M" so we can introduce "F-Commerce," which should go mainstream in 2011. Already several retailers have created small stores on Facebook, and it won't be long before Facebook becomes a full-fledged channel in the omni-channel world of retail. The battle between Facebook and Google will heat up over retail, where both stand to make lots of money. JCPenney and ASOS both put their entire catalogs on Facebook, and lots of other retailers have connected Facebook to their e-commerce site. I still think selling from the newsfeed is the best approach, and several retailers are trying that approach as well. I just don’t see Google+ as a threat to Facebook, so I think that battle is over.  I called 2011 The Year of F-Commerce, and that was probably accurate. Its good to look back at predictions, but we also have to think about what was missed.  I didn't see Amazon entering the tablet business with such a splash, although in hindsight it was obvious. Nor did I think HP would fall so far so fast.  Look for my 2012 predictions coming soon.

    Read the article

  • I Clobbered a Leopard with a Window Last Night

    - by D'Arcy Lussier
    I’ve had my 15” Mac Book Pro for a little over a year now, and its hands-down the best laptop I’ve ever owned…hardware wise. And I tried, I really really tried, to like OSX. I even bought Parallels so I could run Windows 7 and all my development tools while still trying to live in an OSX world. But in the end, I missed Windows too much. There were just too many shortcomings with OSX that kept me from being productive. For one thing, Office for Mac is *not* Office for Windows. The applications are written by different teams, and Excel on the Mac is just different enough to be painful. The VM experience was adequate, but my MBP would heat up like crazy when running it and the experience trying to get Windows apps to interact with an OSX file system was awkward. And I found I was in the VM more than I thought I’d be. iMovie is not as easy to use for doing simple movie editing as Windows Movie Maker. There’s no free blog editing software for OSX that’s on par with Windows Live Writer. And really, all I was using OSX for was Twitter (which I can use a Windows client for) and web browsing (also something Windows can provide obviously). So I had to ask myself – why am I forcing myself to use an operating system I don’t like, on a laptop that can support Windows 7? And so I paved my MBP and am happily running Windows 7 on it…and its fantastic! All the good stuff with the hardware is still there with the goodness of Win 7. Happy happy. I did run into some snags doing this though, and that’s really what this blog post is about – things to be aware of if you want to install Win 7 directly on your MBP metal. First, Ensure You Have Your Original Mac Install Disk This was a warning my buddy Dylan, who’s been running Win 7 on his MBP for a while now, gave me early on. The reason you need that original disk is that the hardware drivers you need are all located there. Apparently you can’t easily download them, so make sure you have them ahead of time. Second, Forget BootCamp The only reason you need BootCamp is if you still want the option to boot into OSX. If you don’t, then you don’t need BootCamp. In fact, you don’t even need BootCamp to install Win 7. What you *will* need though is a DVD with Win 7 burnt on it. Apple doesn’t support bootable USB drives. Well, actually they do for Mac Book Airs which don’t come with optical drives…but to get it working you’ll need to edit a system file of BootCamp so your make of MBP is included in an XML document, and even then you *still* are using BootCamp meaning you’ll be making an OSX partition. So don’t worry about BootCamp, just burn a Windows 7 disc, put it into the DVD drive, and restart your MBP. Third, Know The Secret Commands So after putting in the Windows 7 DVD and restarting your MBP, you’ll want to hold down the ‘C’ key during boot up. This tells the MBP that it should boot from the DVD drive instead of the hard drive. Interestingly, it appears you don’t have to do this if its the Mac OSX install disc (more on that in a second), but regardless – hold down C and Windows will start the install process. Next up is the partition process. You’ll notice that there’s a partition called ETI or something like that. This has to do with the drive format that Apple uses and how they partition their system drives. What I did – I blew it away! At first I didn’t, but I was told I couldn’t install Windows on the remaining space due to the different drive format. Blowing away the ETI partition (and all other partitions) allowed me to continue the Windows install. *REMEMBER –  No warranty is provided or implied, just telling you what I did and how I got it to work. Ok, so now Windows is installed and I’m rebooting. Everything looks good, but I need drivers! So I put in the OSX install DVD and run the BootCamp assistant which installs all the Windows drivers I need. Fantastic! Oh, I need to restart – no problem. OH NO, PROBLEM! I left the OSX install DVD in the drive and now the MBP wants to boot from the drive and install OSX! I’m not holding down the C key, what the heck?! Ok, well there must be a way to eject this disk…hmm…no physical button on the side…the eject button doesn’t seem to work on the keyboard…no little pin hole to insert something to force the disc out…well what the…?! It turns out, if you want to eject a disc at boot up, you need (and I kid you not) to plug a mouse into the laptop and hold down the right-click button while its booting. This ejected the disc for me. Seriously. Finally, Things You Should Be Aware Of Once you have Windows up and running there’s a few things you need to be aware of, mainly new keyboard shortcuts. For instance, on the Mac keyboard there is no Home, End, PageUp or PageDown. There’s also no obvious way to do something like select large amounts of text (like you would by holding Shift-Home at the end of a line of text for instance). So here’s some shortcuts you need to know: Home – fn + left arrow End – fn + right arrow Select a line of text as you would with the Home key – Shift + fn + left arrow Select a line of text as you would with the End key – Shift + fn + right arrow Page Up – fn + up arrow Page Down – fn + down arrow Also, you’ll notice that the awesome Mac track pad doesn’t respond to taps as clicks. No fear, this is just a setting that needs to be altered in the BootCamp control panel (that controls the Mac Hardware-specific settings within Windows, you can access it easily from the system tray icon) One other thing, battery life seems a bit lower than with OSX, but then again I’m also doing more than Twitter or web browsing on this thing now. Conclusion My laptop runs awesome now that I have Windows 7 on there. It’s obviously up to individual taste, but for me I just didn’t see benefits to living in an OSX world when everything I needed lived in Windows. And also, I finally am back to an operating system that doesn’t require me to eject a USB drive before physically removing it! It’s 2012 folks, how has this not been fixed?! D

    Read the article

  • WiX 3 Tutorial: Custom EULA License and MSI localization

    - by Mladen Prajdic
    In this part of the ongoing Wix tutorial series we’ll take a look at how to localize your MSI into different languages. We’re still the mighty SuperForm: Program that takes care of all your label color needs. :) Localizing the MSI With WiX 3.0 localizing an MSI is pretty much a simple and straightforward process. First let look at the WiX project Properties->Build. There you can see "Cultures to build" textbox. Put specific cultures to build into the testbox or leave it empty to build all of them. Cultures have to be in correct culture format like en-US, en-GB or de-DE. Next we have to tell WiX which cultures we actually have in our project. Take a look at the first post in the series about Solution/Project structure and look at the Lang directory in the project structure picture. There we have de-de and en-us subfolders each with its own localized stuff. In the subfolders pay attention to the WXL files Loc_de-de.wxl and Loc_en-us.wxl. Each one has a <String Id="LANG"> under the WixLocalization root node. By including the string with id LANG we tell WiX we want that culture built. For English we have <String Id="LANG">1033</String>, for German <String Id="LANG">1031</String> in Loc_de-de.wxl and for French we’d have to create another file Loc_fr-FR.wxl and put <String Id="LANG">1036</String>. WXL files are localization files. Any string we want to localize we have to put in there. To reference it we use loc keyword like this: !(loc.IdOfTheVariable) => !(loc.MustCloseSuperForm) This is our Loc_en-us.wxl. Note that German wxl has an identical structure but values are in German. <?xml version="1.0" encoding="utf-8"?><WixLocalization Culture="en-us" xmlns="http://schemas.microsoft.com/wix/2006/localization" Codepage="1252"> <String Id="LANG">1033</String> <String Id="ProductName">SuperForm</String> <String Id="LicenseRtf" Overridable="yes">\Lang\en-us\EULA_en-us.rtf</String> <String Id="ManufacturerName">My Company Name</String> <String Id="AppNotSupported">This application is is not supported on your current OS. Minimal OS supported is Windows XP SP2</String> <String Id="DotNetFrameworkNeeded">.NET Framework 3.5 is required. Please install the .NET Framework then run this installer again.</String> <String Id="MustCloseSuperForm">Must close SuperForm!</String> <String Id="SuperFormNewerVersionInstalled">A newer version of !(loc.ProductName) is already installed.</String> <String Id="ProductKeyCheckDialog_Title">!(loc.ProductName) setup</String> <String Id="ProductKeyCheckDialogControls_Title">!(loc.ProductName) Product check</String> <String Id="ProductKeyCheckDialogControls_Description">Plese Enter following information to perform the licence check.</String> <String Id="ProductKeyCheckDialogControls_FullName">Full Name:</String> <String Id="ProductKeyCheckDialogControls_Organization">Organization:</String> <String Id="ProductKeyCheckDialogControls_ProductKey">Product Key:</String> <String Id="ProductKeyCheckDialogControls_InvalidProductKey">The product key you entered is invalid. Please call user support.</String> </WixLocalization>   As you can see from the file we can use localization variables in other variables like we do for SuperFormNewerVersionInstalled string. ProductKeyCheckDialog* strings are to localize a custom dialog for Product key check which we’ll look at in the next post. Built in dialog text localization Under the de-de folder there’s also the WixUI_de-de.wxl file. This files contains German translations of all texts that are in WiX built in dialogs. It can be downloaded from WiX 3.0.5419.0 Source Forge site. Download the wix3-sources.zip and go to \src\ext\UIExtension\wixlib. There you’ll find already translated all WiX texts in 12 Languages. Localizing the custom EULA license Here it gets ugly. We can override the default EULA license easily by overriding WixUILicenseRtf WiX variable like this: <WixVariable Id="WixUILicenseRtf" Value="License.rtf" /> where License.rtf is the name of your custom EULA license file. The downside of this method is that you can only have one license file which means no localization for it. That’s why we need to make a workaround. License is checked on a dialog name LicenseAgreementDialog. What we have to do is overwrite that dialog and insert the functionality for localization. This is a code for LicenseAgreementDialogOverwritten.wxs, an overwritten LicenseAgreementDialog that supports localization. LicenseAcceptedOverwritten replaces the LicenseAccepted built in variable. <?xml version="1.0" encoding="UTF-8" ?><Wix xmlns="http://schemas.microsoft.com/wix/2006/wi"> <Fragment> <UI> <Dialog Id="LicenseAgreementDialogOverwritten" Width="370" Height="270" Title="!(loc.LicenseAgreementDlg_Title)"> <Control Id="LicenseAcceptedOverwrittenCheckBox" Type="CheckBox" X="20" Y="207" Width="330" Height="18" CheckBoxValue="1" Property="LicenseAcceptedOverwritten" Text="!(loc.LicenseAgreementDlgLicenseAcceptedCheckBox)" /> <Control Id="Back" Type="PushButton" X="180" Y="243" Width="56" Height="17" Text="!(loc.WixUIBack)" /> <Control Id="Next" Type="PushButton" X="236" Y="243" Width="56" Height="17" Default="yes" Text="!(loc.WixUINext)"> <Publish Event="SpawnWaitDialog" Value="WaitForCostingDlg">CostingComplete = 1</Publish> <Condition Action="disable"> <![CDATA[ LicenseAcceptedOverwritten <> "1" ]]> </Condition> <Condition Action="enable">LicenseAcceptedOverwritten = "1"</Condition> </Control> <Control Id="Cancel" Type="PushButton" X="304" Y="243" Width="56" Height="17" Cancel="yes" Text="!(loc.WixUICancel)"> <Publish Event="SpawnDialog" Value="CancelDlg">1</Publish> </Control> <Control Id="BannerBitmap" Type="Bitmap" X="0" Y="0" Width="370" Height="44" TabSkip="no" Text="!(loc.LicenseAgreementDlgBannerBitmap)" /> <Control Id="LicenseText" Type="ScrollableText" X="20" Y="60" Width="330" Height="140" Sunken="yes" TabSkip="no"> <!-- This is original line --> <!--<Text SourceFile="!(wix.WixUILicenseRtf=$(var.LicenseRtf))" />--> <!-- To enable EULA localization we change it to this --> <Text SourceFile="$(var.ProjectDir)\!(loc.LicenseRtf)" /> <!-- In each of localization files (wxl) put line like this: <String Id="LicenseRtf" Overridable="yes">\Lang\en-us\EULA_en-us.rtf</String>--> </Control> <Control Id="Print" Type="PushButton" X="112" Y="243" Width="56" Height="17" Text="!(loc.WixUIPrint)"> <Publish Event="DoAction" Value="WixUIPrintEula">1</Publish> </Control> <Control Id="BannerLine" Type="Line" X="0" Y="44" Width="370" Height="0" /> <Control Id="BottomLine" Type="Line" X="0" Y="234" Width="370" Height="0" /> <Control Id="Description" Type="Text" X="25" Y="23" Width="340" Height="15" Transparent="yes" NoPrefix="yes" Text="!(loc.LicenseAgreementDlgDescription)" /> <Control Id="Title" Type="Text" X="15" Y="6" Width="200" Height="15" Transparent="yes" NoPrefix="yes" Text="!(loc.LicenseAgreementDlgTitle)" /> </Dialog> </UI> </Fragment></Wix>   Look at the Control with Id "LicenseText” and read the comments. We’ve changed the original license text source to "$(var.ProjectDir)\!(loc.LicenseRtf)". var.ProjectDir is the directory of the project file. The !(loc.LicenseRtf) is where the magic happens. Scroll up and take a look at the wxl localization file example. We have the LicenseRtf declared there and it’s been made overridable so developers can change it if they want. The value of the LicenseRtf is the path to our localized EULA relative to the WiX project directory. With little hacking we’ve achieved a fully localizable installer package.   The final step is to insert the extended LicenseAgreementDialogOverwritten license dialog into the installer GUI chain. This is how it’s done under the <UI> node of course.   <UI> <!-- code to be discussed in later posts –> <!-- BEGIN UI LOGIC FOR CLEAN INSTALLER --> <Publish Dialog="WelcomeDlg" Control="Next" Event="NewDialog" Value="LicenseAgreementDialogOverwritten">1</Publish> <Publish Dialog="LicenseAgreementDialogOverwritten" Control="Back" Event="NewDialog" Value="WelcomeDlg">1</Publish> <Publish Dialog="LicenseAgreementDialogOverwritten" Control="Next" Event="NewDialog" Value="ProductKeyCheckDialog">LicenseAcceptedOverwritten = "1" AND NOT OLDER_VERSION_FOUND</Publish> <Publish Dialog="InstallDirDlg" Control="Back" Event="NewDialog" Value="ProductKeyCheckDialog">1</Publish> <!-- END UI LOGIC FOR CLEAN INSTALLER –> <!-- code to be discussed in later posts --></UI> For a thing that should be simple for the end developer to do, localization can be a bit advanced for the novice WiXer. Hope this post makes the journey easier and that next versions of WiX improve this process. WiX 3 tutorial by Mladen Prajdic navigation WiX 3 Tutorial: Solution/Project structure and Dev resources WiX 3 Tutorial: Understanding main wxs and wxi file WiX 3 Tutorial: Generating file/directory fragments with Heat.exe  WiX 3 Tutorial: Custom EULA License and MSI localization WiX 3 Tutorial: Product Key Check custom action WiX 3 Tutorial: Building an updater WiX 3 Tutorial: Icons and installer pictures WiX 3 Tutorial: Creating a Bootstrapper

    Read the article

  • WiX 3 Tutorial: Understanding main WXS and WXI file

    - by Mladen Prajdic
    In the previous post we’ve taken a look at the WiX solution/project structure and project properties. We’re still playing with our super SuperForm application and today we’ll take a look at the general parts of the main wxs file, SuperForm.wxs, and the wxi include file. For wxs file we’ll just go over the general description of what each part does in the code comments. The more detailed descriptions will be in future posts about features themselves. WXI include file Include files are exactly what their name implies. To include a wxi file into the wxs file you have to put the wxi at the beginning of each .wxs file you wish to include it in. If you’ve ever worked with C++ you can think of the include files as .h files. For example if you include SuperFormVariables.wxi into the SuperForm.wxs, the variables in the wxi won’t be seen in FilesFragment.wxs or RegistryFragment.wxs. You’d have to include it manually into those two wxs files too. For preprocessor variable $(var.VariableName) to be seen by every file in the project you have to include them in the WiX project properties->Build->“Define preprocessor variables” textbox. This is why I’ve chosen not to go this route because in multi developer teams not everyone has the same directory structure and having a single variable would mean each developer would have to checkout the wixproj file to edit the variable. This is pretty much unacceptable by my standards. This is why we’ve added a System Environment variable named SuperFormFilesDir as is shown in the previous Wix Tutorial post. Because the FilesFragment.wxs is autogenerated on every project build we don’t want to change it manually each time by adding the include wxi at the beginning of the file. This way we couldn’t recreate it in each pre-build event. <?xml version="1.0" encoding="utf-8"?><Include> <!-- Versioning. These have to be changed for upgrades. It's not enough to just include newer files. --> <?define MajorVersion="1" ?> <?define MinorVersion="0" ?> <?define BuildVersion="0" ?> <!-- Revision is NOT used by WiX in the upgrade procedure --> <?define Revision="0" ?> <!-- Full version number to display --> <?define VersionNumber="$(var.MajorVersion).$(var.MinorVersion).$(var.BuildVersion).$(var.Revision)" ?> <!-- Upgrade code HAS to be the same for all updates. Once you've chosen it don't change it. --> <?define UpgradeCode="YOUR-GUID-HERE" ?> <!-- Path to the resources directory. resources don't really need to be included in the project structure but I like to include them for for clarity --> <?define ResourcesDir="$(var.ProjectDir)\Resources" ?> <!-- The name of your application exe file. This will be used to kill the process when updating and creating the desktop shortcut --> <?define ExeProcessName="SuperForm.MainApp.exe" ?></Include> For now there’s no way to tell WiX in Visual Studio to have a wxi include file available to the whole project, so you have to include it in each file separately. Only variables set in “Define preprocessor variables” or System Environment variables are accessible to the whole project for now. The main WXS file: SuperForm.wxs We’ll only take a look at the general structure of the main SuperForm.wxs and not its the details. We’ll cover the details in future posts. The code comments should provide plenty info about what each part does in general. Basically there are 5 major parts. The update part, the conditions and actions part, the UI install sequence, the directory structure and the features we want to include. <?xml version="1.0" encoding="UTF-8"?><!-- Add xmlns:util namespace definition to be able to use stuff from WixUtilExtension dll--><Wix xmlns="http://schemas.microsoft.com/wix/2006/wi" xmlns:util="http://schemas.microsoft.com/wix/UtilExtension"> <!-- This is how we include wxi files --> <?include $(sys.CURRENTDIR)Includes\SuperFormVariables.wxi ?> <!-- Id="*" is to enable upgrading. * means that the product ID will be autogenerated on each build. Name is made of localized product name and version number. --> <Product Id="*" Name="!(loc.ProductName) $(var.VersionNumber)" Language="!(loc.LANG)" Version="$(var.VersionNumber)" Manufacturer="!(loc.ManufacturerName)" UpgradeCode="$(var.UpgradeCode)"> <!-- Define the minimum supported installer version (3.0) and that the install should be done for the whole machine not just the current user --> <Package InstallerVersion="300" Compressed="yes" InstallScope="perMachine"/> <Media Id="1" Cabinet="media1.cab" EmbedCab="yes" /> <!-- Upgrade settings. This will be explained in more detail in a future post --> <Upgrade Id="$(var.UpgradeCode)"> <UpgradeVersion OnlyDetect="yes" Minimum="$(var.VersionNumber)" IncludeMinimum="no" Property="NEWER_VERSION_FOUND" /> <UpgradeVersion Minimum="0.0.0.0" IncludeMinimum="yes" Maximum="$(var.VersionNumber)" IncludeMaximum="no" Property="OLDER_VERSION_FOUND" /> </Upgrade> <!-- Reference the global NETFRAMEWORK35 property to check if it exists --> <PropertyRef Id="NETFRAMEWORK35"/> <!-- Startup conditions that checks if .Net Framework 3.5 is installed or if we're running the OS higher than Windows XP SP2. If not the installation is aborted. By doing the (Installed OR ...) property means that this condition will only be evaluated if the app is being installed and not on uninstall or changing --> <Condition Message="!(loc.DotNetFrameworkNeeded)"> <![CDATA[Installed OR NETFRAMEWORK35]]> </Condition> <Condition Message="!(loc.AppNotSupported)"> <![CDATA[Installed OR ((VersionNT >= 501 AND ServicePackLevel >= 2) OR (VersionNT >= 502))]]> </Condition> <!-- This custom action in the InstallExecuteSequence is needed to stop silent install (passing /qb to msiexec) from going around it. --> <CustomAction Id="NewerVersionFound" Error="!(loc.SuperFormNewerVersionInstalled)" /> <InstallExecuteSequence> <!-- Check for newer versions with FindRelatedProducts and execute the custom action after it --> <Custom Action="NewerVersionFound" After="FindRelatedProducts"> <![CDATA[NEWER_VERSION_FOUND]]> </Custom> <!-- Remove the previous versions of the product --> <RemoveExistingProducts After="InstallInitialize"/> <!-- WixCloseApplications is a built in custom action that uses util:CloseApplication below --> <Custom Action="WixCloseApplications" Before="InstallInitialize" /> </InstallExecuteSequence> <!-- This will ask the user to close the SuperForm app if it's running while upgrading --> <util:CloseApplication Id="CloseSuperForm" CloseMessage="no" Description="!(loc.MustCloseSuperForm)" ElevatedCloseMessage="no" RebootPrompt="no" Target="$(var.ExeProcessName)" /> <!-- Use the built in WixUI_InstallDir GUI --> <UIRef Id="WixUI_InstallDir" /> <UI> <!-- These dialog references are needed for CloseApplication above to work correctly --> <DialogRef Id="FilesInUse" /> <DialogRef Id="MsiRMFilesInUse" /> <!-- Here we'll add the GUI logic for installation and updating in a future post--> </UI> <!-- Set the icon to show next to the program name in Add/Remove programs --> <Icon Id="SuperFormIcon.ico" SourceFile="$(var.ResourcesDir)\Exclam.ico" /> <Property Id="ARPPRODUCTICON" Value="SuperFormIcon.ico" /> <!-- Installer UI custom pictures. File names are made up. Add path to your pics. –> <!-- <WixVariable Id="WixUIDialogBmp" Value="MyAppLogo.jpg" /> <WixVariable Id="WixUIBannerBmp" Value="installBanner.jpg" /> --> <!-- the default directory structure --> <Directory Id="TARGETDIR" Name="SourceDir"> <Directory Id="ProgramFilesFolder"> <Directory Id="INSTALLLOCATION" Name="!(loc.ProductName)" /> </Directory> </Directory> <!-- Set the default install location to the value of INSTALLLOCATION (usually c:\Program Files\YourProductName) --> <Property Id="WIXUI_INSTALLDIR" Value="INSTALLLOCATION" /> <!-- Set the components defined in our fragment files that will be used for our feature --> <Feature Id="SuperFormFeature" Title="!(loc.ProductName)" Level="1"> <ComponentGroupRef Id="SuperFormFiles" /> <ComponentRef Id="cmpVersionInRegistry" /> <ComponentRef Id="cmpIsThisUpdateInRegistry" /> </Feature> </Product></Wix> For more info on what certain attributes mean you should look into the WiX Documentation.   WiX 3 tutorial by Mladen Prajdic navigation WiX 3 Tutorial: Solution/Project structure and Dev resources WiX 3 Tutorial: Understanding main wxs and wxi file WiX 3 Tutorial: Generating file/directory fragments with Heat.exe

    Read the article

  • Azure Grid Computing - Worker Roles as HPC Compute Nodes

    - by JoshReuben
    Overview ·        With HPC 2008 R2 SP1 You can add Azure worker roles as compute nodes in a local Windows HPC Server cluster. ·        The subscription for Windows Azure like any other Azure Service - charged for the time that the role instances are available, as well as for the compute and storage services that are used on the nodes. ·        Win-Win ? - Azure charges the computer hour cost (according to vm size) amortized over a month – so you save on purchasing compute node hardware. Microsoft wins because you need to purchase HPC to have a local head node for managing this compute cluster grid distributed in the cloud. ·        Blob storage is used to hold input & output files of each job. I can see how Parametric Sweep HPC jobs can be supported (where the same job is run multiple times on each node against different input units), but not MPI.NET (where different HPC Job instances function as coordinated agents and conduct master-slave inter-process communication), unless Azure is somehow tunneling MPI communication through inter-WorkerRole Azure Queues. ·        this is not the end of the story for Azure Grid Computing. If MS requires you to purchase a local HPC license (and administrate it), what's to stop a 3rd party from doing this and encapsulating exposing HPC WCF Broker Service to you for managing compute nodes? If MS doesn’t  provide head node as a service, someone else will! Process ·        requires creation of a worker node template that specifies a connection to an existing subscription for Windows Azure + an availability policy for the worker nodes. ·        After worker nodes are added to the cluster, you can start them, which provisions the Windows Azure role instances, and then bring them online to run HPC cluster jobs. ·        A Windows Azure worker role instance runs a HPC compatible Azure guest operating system which runs on the VMs that host your service. The guest operating system is updated monthly. You can choose to upgrade the guest OS for your service automatically each time an update is released - All role instances defined by your service will run on the guest operating system version that you specify. see Windows Azure Guest OS Releases and SDK Compatibility Matrix (http://go.microsoft.com/fwlink/?LinkId=190549). ·        use the hpcpack command to upload file packages and install files to run on the worker nodes. see hpcpack (http://go.microsoft.com/fwlink/?LinkID=205514). Requirements ·        assuming you have an azure subscription account and the HPC head node installed and configured. ·        Install HPC Pack 2008 R2 SP 1 -  see Microsoft HPC Pack 2008 R2 Service Pack 1 Release Notes (http://go.microsoft.com/fwlink/?LinkID=202812). ·        Configure the head node to connect to the Internet - connectivity is provided by the connection of the head node to the enterprise network. You may need to configure a proxy client on the head node. Any cluster network topology (1-5) is supported). ·        Configure the firewall - allow outbound TCP traffic on the following ports: 80,       443, 5901, 5902, 7998, 7999 ·        Note: HPC Server  uses Admin Mode (Elevated Privileges) in Windows Azure to give the service administrator of the subscription the necessary privileges to initialize HPC cluster services on the worker nodes. ·        Obtain a Windows Azure subscription certificate - the Windows Azure subscription must be configured with a public subscription (API) certificate -a valid X.509 certificate with a key size of at least 2048 bits. Generate a self-sign certificate & upload a .cer file to the Windows Azure Portal Account page > Manage my API Certificates link. see Using the Windows Azure Service Management API (http://go.microsoft.com/fwlink/?LinkId=205526). ·        import the certificate with an associated private key on the HPC cluster head node - into the trusted root store of the local computer account. Obtain Windows Azure Connection Information for HPC Server ·        required for each worker node template ·        copy from azure portal - Get from: navigation pane > Hosted Services > Storage Accounts & CDN ·        Subscription ID - a 32-char hex string in the form xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx. In Properties pane. ·        Subscription certificate thumbprint - a 40-char hex string (you need to remove spaces). In Management Certificates > Properties pane. ·        Service name - the value of <ServiceName> configured in the public URL of the service (http://<ServiceName>.cloudapp.net). In Hosted Services > Properties pane. ·        Blob Storage account name - the value of <StorageAccountName> configured in the public URL of the account (http://<StorageAccountName>.blob.core.windows.net). In Storage Accounts > Properties pane. Import the Azure Subscription Certificate on the HPC Head Node ·        enable the services for Windows HPC Server  to authenticate properly with the Windows Azure subscription. ·        use the Certificates MMC snap-in to import the certificate to the Trusted Root Certification Authorities store of the local computer account. The certificate must be in PFX format (.pfx or .p12 file) with a private key that is protected by a password. ·        see Certificates (http://go.microsoft.com/fwlink/?LinkId=163918). ·        To open the certificates snapin: Run > mmc. File > Add/Remove Snap-in > certificates > Computer account > Local Computer ·        To import the certificate via wizard - Certificates > Trusted Root Certification Authorities > Certificates > All Tasks > Import ·        After the certificate is imported, it appears in the details pane in the Certificates snap-in. You can open the certificate to check its status. Configure a Proxy Client on the HPC Head Node ·        the following Windows HPC Server services must be able to communicate over the Internet (through the firewall) with the services for Windows Azure: HPCManagement, HPCScheduler, HPCBrokerWorker. ·        Create a Windows Azure Worker Node Template ·        Edit HPC node templates in HPC Node Template Editor. ·        Specify: 1) Windows Azure subscription connection info (unique service name) for adding a set of worker nodes to the cluster + 2)worker node availability policy – rules for deploying / removing worker role instances in Windows Azure o   HPC Cluster Manager > Configuration > Navigation Pane > Node Templates > Actions pane > New à Create Node Template Wizard or Edit à Node Template Editor o   Choose Node Template Type page - Windows Azure worker node template o   Specify Template Name page – template name & description o   Provide Connection Information page – Azure Subscription ID (text) & Subscription certificate (browse) o   Provide Service Information page - Azure service name + blob storage account name (optionally click Retrieve Connection Information to get list of available from azure – possible LRT). o   Configure Azure Availability Policy page - how Windows Azure worker nodes start / stop (online / offline the worker role instance -  add / remove) – manual / automatic o   for automatic - In the Configure Windows Azure Worker Availability Policy dialog -select days and hours for worker nodes to start / stop. ·        To validate the Windows Azure connection information, on the template's Connection Information tab > Validate connection information. ·        You can upload a file package to the storage account that is specified in the template - eg upload application or service files that will run on the worker nodes. see hpcpack (http://go.microsoft.com/fwlink/?LinkID=205514). Add Azure Worker Nodes to the HPC Cluster ·        Use the Add Node Wizard – specify: 1) the worker node template, 2) The number of worker nodes   (within the quota of role instances in the azure subscription), and 3)           The VM size of the worker nodes : ExtraSmall, Small, Medium, Large, or ExtraLarge.  ·        to add worker nodes of different sizes, must run the Add Node Wizard separately for each size. ·        All worker nodes that are added to the cluster by using a specific worker node template define a set of worker nodes that will be deployed and managed together in Windows Azure when you start the nodes. This includes worker nodes that you add later by using the worker node template and, if you choose, worker nodes of different sizes. You cannot start, stop, or delete individual worker nodes. ·        To add Windows Azure worker nodes o   In HPC Cluster Manager: Node Management > Actions pane > Add Node à Add Node Wizard o   Select Deployment Method page - Add Azure Worker nodes o   Specify New Nodes page - select a worker node template, specify the number and size of the worker nodes ·        After you add worker nodes to the cluster, they are in the Not-Deployed state, and they have a health state of Unapproved. Before you can use the worker nodes to run jobs, you must start them and then bring them online. ·        Worker nodes are numbered consecutively in a naming series that begins with the root name AzureCN – this is non-configurable. Deploying Windows Azure Worker Nodes ·        To deploy the role instances in Windows Azure - start the worker nodes added to the HPC cluster and bring the nodes online so that they are available to run cluster jobs. This can be configured in the HPC Azure Worker Node Template – Azure Availability Policy -  to be automatic or manual. ·        The Start, Stop, and Delete actions take place on the set of worker nodes that are configured by a specific worker node template. You cannot perform one of these actions on a single worker node in a set. You also cannot perform a single action on two sets of worker nodes (specified by two different worker node templates). ·        ·          Starting a set of worker nodes deploys a set of worker role instances in Windows Azure, which can take some time to complete, depending on the number of worker nodes and the performance of Windows Azure. ·        To start worker nodes manually and bring them online o   In HPC Node Management > Navigation Pane > Nodes > List / Heat Map view - select one or more worker nodes. o   Actions pane > Start – in the Start Azure Worker Nodes dialog, select a node template. o   the state of the worker nodes changes from Not Deployed to track the provisioning progress – worker node Details Pane > Provisioning Log tab. o   If there were errors during the provisioning of one or more worker nodes, the state of those nodes is set to Unknown and the node health is set to Unapproved. To determine the reason for the failure, review the provisioning logs for the nodes. o   After a worker node starts successfully, the node state changes to Offline. To bring the nodes online, select the nodes that are in the Offline state > Bring Online. ·        Troubleshooting o   check node template. o   use telnet to test connectivity: telnet <ServiceName>.cloudapp.net 7999 o   check node status - Deployment status information appears in the service account information in the Windows Azure Portal - HPC queries this -  see  node status information for any failed nodes in HPC Node Management. ·        When role instances are deployed, file packages that were previously uploaded to the storage account using the hpcpack command are automatically installed. You can also upload file packages to storage after the worker nodes are started, and then manually install them on the worker nodes. see hpcpack (http://go.microsoft.com/fwlink/?LinkID=205514). ·        to remove a set of role instances in Windows Azure - stop the nodes by using HPC Cluster Manager (apply the Stop action). This deletes the role instances from the service and changes the state of the worker nodes in the HPC cluster to Not Deployed. ·        Each time that you start a set of worker nodes, two proxy role instances (size Small) are configured in Windows Azure to facilitate communication between HPC Cluster Manager and the worker nodes. The proxy role instances are not listed in HPC Cluster Manager after the worker nodes are added. However, the instances appear in the Windows Azure Portal. The proxy role instances incur charges in Windows Azure along with the worker node instances, and they count toward the quota of role instances in the subscription.

    Read the article

  • Ada and 'The Book'

    - by Phil Factor
    The long friendship between Charles Babbage and Ada Lovelace created one of the most exciting and mysterious of collaborations ever to have resulted in a technological breakthrough. The fireworks that created by the collision of two prodigious mathematical and creative talents resulted in an invention, the Analytical Engine, which went on to change society fundamentally. However, beyond that, we just don't know what the bulk of their collaborative work was about:;  it was done in strictest secrecy. Even the known outcome of their friendship, the first programmable computer, was shrouded in mystery. At the time, nobody, except close friends and family, had any idea of Ada Byron's contribution to the invention of the ‘Engine’, and how to program it. Her great insight was published in August 1843, under the initials AAL, standing for Ada Augusta Lovelace, her title then being the Countess of Lovelace. It was contained in a lengthy ‘note’ to her translation of a publication that remains the best description of Babbage's amazing Analytical Engine. The secret identity of the person behind those enigmatic initials was finally revealed by Prince de Polignac who, seventy years later, wrote to Ada's daughter to seek confirmation that her mother had, indeed, been the author of the brilliant sentences that described so accurately how Babbage's mechanical computer could be programmed with punch-cards. L.F. Menabrea's paper on the Analytical Engine first appeared in the 'Bibliotheque Universelle de Geneve' in October 1842, and Ada translated it anonymously for Taylor's 'Scientific Memoirs'. Charles Babbage was surprised that she had not written an original paper as she already knew a surprising amount about the way the machine worked. He persuaded her to at least write some explanatory notes. These notes ended up extending to four times the length of the original article and represented the first published account of how a machine could be programmed to perform any calculation. Her example of programming the Bernoulli sequence would have worked on the Analytical engine had the device’s construction been completed, and gave Ada an unassailable claim to have invented the art of programming. What was the reason for Ada's secrecy? She was the only legitimate child of Lord Byron, who was probably the best known celebrity of the age, so she was already famous. She was a senior aristocrat, with titles, a fortune in money and vast estates in the Midlands. She had political influence, and was the cousin of Lord Melbourne, who was the Prime Minister at that time. She was friendly with the young Queen Victoria. Her mathematical activities were a pastime, and not one that would be considered by others to be in keeping with her roles and responsibilities. You wouldn't dare to dream up a fictional heroine like Ada. She was dazzlingly beautiful and talented. She could speak several languages fluently, and play some musical instruments with professional skill. Contemporary accounts refer to her being 'accomplished in science, art and literature'. On top of that, she was a brilliant mathematician, a talent inherited from her mother, Annabella Milbanke. In her mother's circle of literary and scientific friends was Charles Babbage, and Ada's friendship with him dates from her teenage zest for Mathematics. She was one of the first people he'd ever met who understood what he had attempted to achieve with the 'Difference Engine', and with whom he could converse as intellectual equals. He arranged for her to have an education from the most talented academics in the country. Ada melted the heart of the cantankerous genius to the point that he became a faithful and loyal father-figure to her. She was one of the very few who could grasp the principles of the later, and very different, ‘Analytical Engine’ which was designed from the start to tackle a variety of tasks. Sadly, Ada Byron's life ended less than a decade after completing the work that assured her long-term fame, in November 1852. She was dying of cancer, her gambling habits had caused her to run up huge debts, she'd had more than one affairs, and she was being blackmailed. Her brilliant but unempathic mother was nursing her in her final illness, destroying her personal letters and records, and repaying her debts. Her husband was distraught but helpless. Charles Babbage, however, maintained his steadfast paternalistic friendship to the end. She appointed her loyal friend to be her executor. For years, she and Babbage had been working together on a secret project, known only as 'The Book'. We have a clue to what it was in a letter written by her nine years earlier, on 11th August 1843. It was a joint project by herself and Lord Lovelace, her husband, and was intended to involve Babbage's 'undivided energies'. It involved 'consulting your Engine' (it required Babbage’s computer). The letter gives no hint about the project except for the high-minded nature of its purpose, and its highly mathematical nature.  From then on, the surviving correspondence between the two gives only veiled references to 'The Book'. There isn't much, since Babbage later destroyed any letters that could have damaged her reputation within the Establishment. 'I cannot spare the book today, which I am very sorry for. At the moment I want it for constant reference, but I think you can have it tomorrow' (Oct 1844)  And 'I will send you the book directly, and you can say, when you receive it, how long you will want to keep it'. (Nov 1844)  The two of them were obviously intent on the work: She writes, four years later, 'I have an engagement for Wednesday which will prevent me from attending to your wishes about the book' (Dec 1848). This was something that they both needed to work on, but could not do in parallel: 'I will send the book on Tuesday, and it can be left with you till Friday' (11 Feb 1849). After six years work, it had been so well-handled that it was beginning to fall apart: 'Don't forget the new cover you promised for the book. The poor book is very shabby and wants one' (20 Sept 1849). So what was going on? The word 'book' was not a code-word: it was a real book, probably a 'printer's blank', plain paper, but properly bound so printers and publishers could show off how the published work might look. The hints from the correspondence are of advanced mathematics. It is obvious that the book was travelling between them, back and forth, each one working on it for less than a week before passing it back. Ada and her husband were certainly involved in gambling large sums of money on the horses, and so most biographers have concluded that the three of them were trying to calculate the mathematical odds on the horses. This theory has three large problems. Firstly, Ada's original letter proposing the project refers to its high-minded nature. Babbage was temperamentally opposed to gambling and would scarcely have given so much time to the project, even though he was devoted to Ada. Secondly, Babbage would have very soon have realized the hopelessness of trying to beat the bookies. This sort of betting never attracts his type of intellectual background. The third problem is that any work on calculating the odds on horses would not need a well-thumbed book to pass back and forth between them; they would have not had to work in series. The original project was instigated by Ada, along with her husband, William King-Noel, 1st Earl of Lovelace. Charles Babbage was invited to join the project after the couple had come up with the idea. What could William have contributed? One might assume that William was a Bertie Wooster character, addicted only to the joys of the turf, but this was far from the truth. He was a scientist, a Cambridge graduate who was later elected to be a Fellow of the Royal Society. After Eton, he went to Trinity College, Cambridge. On graduation, he entered the diplomatic service and acted as secretary under Lord Nugent, who was Lord Commissioner of the Ionian Islands. William was very friendly with Babbage too, able to discuss scientific matters on equal terms. He was a capable engineer who invented a process for bending large timbers by the application of steam heat. He delivered a paper to the Institution of Civil Engineers in 1849, and received praise from the great engineer, Isambard Kingdom Brunel. As well as being Lord Lieutenant of the County of Surrey for most of Victoria's reign, he had time for a string of scientific and engineering achievements. Whatever the project was, it is unlikely that William was a junior partner. After Ada's death, the project disappeared. Then, two years later, Babbage, through one of his occasional outbursts of temper, demonstrated that he was able to decrypt one of the most powerful of secret codes, Vigenère's autokey cipher.  All contemporary diplomatic and military messages used a variant of this cipher. Babbage had made three important discoveries, namely, the mathematical law of this cipher, the principle of the key periodicity, and the technique of the symmetry of position. The technique is now known as the Kasiski examination, also called the Kasiski test, but Babbage got there first. At one time, he listed amongst his future projects, the writing of a book 'The Philosophy of Decyphering', but it never came to anything. This discovery was going to change the course of history, since it was used to decipher the Russians’ military dispatches in the Crimean war. Babbage himself played a role during the Crimean War as a cryptographical adviser to his friend, Rear-Admiral Sir Francis Beaufort of the Admiralty. This is as much as we can be certain about in trying to make sense of the bulk of the time that Charles Babbage and Ada Lovelace worked together. Nine years of intensive work, involving the 'Engine' and a great deal of mathematics and research seems to have been lost: or has it? I've argued in the past http://www.simple-talk.com/community/blogs/philfactor/archive/2008/06/13/59614.aspx that the cracking of the Vigenère autokey cipher, was a fundamental motive behind the British Government's support and funding of the 'Difference Engine'. The Duke of Wellington, whose understanding of the military significance of being able to read enemy dispatches, was the most steadfast advocate of the project. If the three friends were actually doing the work of cracking codes by mathematical techniques that used the techniques of key periodicity, and symmetry of position (the use of a book being passed quickly to and fro is very suggestive), intending to then use the 'Engine' to do the routine cracking of each dispatch, then this is a rather different story. The project was Ada and William's idea. (William had served in the diplomatic service and would be familiar with the use of codes). This makes Ada Lovelace the initiator of a project which, by giving both Britain, and probably the USA, a diplomatic and military advantage in the second part of the Nineteenth century, changed world history. Ada would never have wanted any credit for cracking the cipher, and developing the method that rendered all contemporary military and diplomatic ciphering techniques nugatory; quite the reverse. And it is clear from the gaps in the record of the letters between the collaborators that the evidence was destroyed, probably on her request by her irascible but intensely honorable executor, Charles Babbage. Charles Babbage toyed with the idea of going public, but the Crimean war put an end to that. The British Government had a valuable secret, and intended to keep it that way. Ada and Charles had quite often discussed possible moneymaking projects that would fund the development of the Analytic Engine, the first programmable computer, but their secret work was never in the running as a potential cash cow. I suspect that the British Government was, even then, working on the concealment of a discovery whose value to the nation depended on it remaining so. The success of code-breaking in the Crimean war, and the American Civil war, led to the British and Americans  subsequently giving much more weight and funding to the science of decryption. Paradoxically, this makes Ada's contribution even closer to the creation of Colossus, the first digital computer, at Bletchley Park, specifically to crack the Nazi’s secret codes.

    Read the article

  • The Internet of Things & Commerce: Part 2 -- Interview with Brian Celenza, Commerce Innovation Strategist

    - by Katrina Gosek, Director | Commerce Product Strategy-Oracle
    Internet of Things & Commerce Series: Part 2 (of 3) Welcome back to the second installation of my three part series on the Internet of Things & Commerce. A few weeks ago, I wrote “The Next 7,000 Days” about how we’ve become embedded in a digital architecture in the last 7,000 days since the birth of the internet – an architecture that everyday ties the massive expanse of the internet evermore closely with our physical lives. This blog series explores how this new blend of virtual and material will change how we shop and how businesses sell. Now enjoy reading my interview with Brian Celenza, one of the chief strategists in our Oracle Commerce innovation group. He comments on the past, present, and future of the how the growing Internet of Things relates and will relate to the buying and selling of goods on and offline. -------------------------------------------- QUESTION: You probably have one of the coolest jobs on our team, Brian – and frankly, one of the coolest jobs in our industry. As part of the innovation team for Oracle Commerce, you’re regularly working on bold features and groundbreaking commerce-focused experiences for our vision demos. As you look back over the past couple of years, what is the biggest trend (or trends) you’ve seen in digital commerce that started to bring us closer to this idea of what people are calling an “Internet of Things”? Brian: Well as you look back over the last couple of years, the speed at which change in our industry has moved looks like one of those blurred movement photos – you know the ones where the landscape blurs because the observer is moving so quickly your eye focus can’t keep up. But one thing that is absolutely clear is that the biggest catalyst for that speed of change – especially over the last three years – has been mobile. Mobile technology changed everything. Over the last three years the entire thought process of how to sell on (and offline) has shifted because of mobile technology advances. Particularly for eCommerce professionals who have started to move past the notion of “channels” for selling goods to this notion of “Mobile First”… then the Web site. Or more accurately, that everything – smartphones, web, store, tablet – is just one channel or has to act like one singular access point to the same product catalog, information and content. The most innovative eCommerce professionals realized some time ago that it’s not ideal to build an eCommerce Web site and then build everything on top of or off of it. Rather, they want to build an eCommerce API and then integrate it will all other systems. To accomplish this, they are leveraging all the latest mobile technologies or possibilities mobile technology has opened up: 4G and LTE, GPS, bluetooth, touch screens, apps, html5… How has this all started to come together for shopping experiences on and offline? Well to give you a personal example, I remember visiting an Apple store a few years ago and being amazed that I didn’t have to wait in line because a store associate knew everything about me from my ID – right there on the sales floor – and could check me out anywhere. Then just a few months later (when like any good addict) I went back to get the latest and greatest new gadget, I felt like I was stealing it because I could check myself out with my smartphone. I didn’t even need to see a sales associate OR go to a cash register. Amazing. And since then, all sort sorts of companies across all different types of industries – from food service to apparel –  are starting to see mobile payments in the billions of dollars now thanks not only to the convenience factor but to smart loyalty rewards programs as well. These are just some really simple current examples that come to mind. So many different things have happened in the last couple of years, it’s hard to really absorb all of the quickly – because as soon as you do, everything changes again! Just like that blurry speed photo image. For eCommerce, however, this type of new environment underscores the importance of building an eCommerce API – a platform that has services you can tap in to and build on as the landscape changes at a fever pitch. It’s a mobile first perspective. A web service perspective – particularly if you are thinking of how to engage customers across digital and physical spaces. —— QUESTION: Thanks for bringing us into the present – some really great examples you gave there to put things into perspective. So what do you see as the biggest trend right now around the “Internet of Things” – and what’s coming next few years? Brian: Honestly, even sitting where I am in the innovation group – it’s hard to look out even 12 months because, well, I don’t even think we’ve fully caught up with what is possible now. But I can definitely say that in the last 12 months and in the coming 12 months, in the technology and eCommerce world it’s all about iBeacons. iBeacons are awesome tools we have right now to tie together physical and digital shopping experiences. They know exactly where you are as a shopper and can communicate that to businesses. Currently there seem to be two camps of thought around iBeacons. First, many people are thinking of them like an “indoor GPS”, which to be fair they literally are. The use case this first camp envisions for iBeacons is primarily for advertising and marketing. So they use iBeacons to push location-based promotions to customers if they are close to a store or in a store. You may have seen these types of mobile promotions start to pop up occasionally on your smart phone as you pass by a store you’ve bought from in the past. That’s the work of iBeacons. But in my humble opinion, these promotions probably come too early in the customer journey and although they may be well timed and work to “convert” in some cases, I imagine in most they are just eroding customer trust because they are kind of a “one-size-fits-all” solution rather than one that is taking into account what exactly the customer might be looking for in that particular moment. Maybe they just want more information and a promotion is way too soon for that type of customer. The second camp is more in line with where my thinking falls. In this case, businesses take a more sensitive approach with iBeacons to customers’ needs. Instead of throwing out a “one-size-fits-all” to any passer by with iBeacons, the use case is more around looking at the physical proximity of a customer as an opportunity to provide a service: show expert reviews on a product they may be looking at in a particular aisle of a store, offer the opportunity to compare prices (and then offer a promotion), signal an in-store associate if a customer has been in the store for more than 10 minutes in one place. These are all less intrusive more value-driven uses of iBeacons. And they are more about building customer trust through service. To take this example a bit further into the future realm of “Big Data” and “Internet of Things” businesses could actually use the Oracle Commerce Platform and iBeacons to “silently” track customer movement w/in the store to provide higher quality service. And this doesn’t have to be creepy or intrusive. Simply if a customer has been in a particular department or aisle for more than a 5 or 10 minutes, an in-store associate could come over an offer some assistance already knowing customer preferences from their online profile and maybe even seeing the items in a shopping cart they started at home. None of this has to be revealed to the customer, but it certainly could boost the level of service an in-store sales associate could provide. Or, in another futuristic example, stores could use the digital footprint of the physical store transmitted by iBeacons to generate heat maps of the store that could be tracked over time. Imagine how much you could find out about which parts of the store are more busy during certain parts of the day or seasons. This could completely revolutionize how physical merchandising is deployed or where certain high value / new items are placed. And / or this use of iBeacons could also help businesses figure out if customers are getting held up in certain parts of the store during busy days like Black Friday. If long lines are causing customers to bounce from a physical store and leave those holiday gifts behind, maybe having employees with mobile check as an option could remove the cash register bottleneck. But going to back to my original statement, it’s all still very early in the story for iBeacons. The hardware manufacturers are still very new and there is still not one clear standard.  Honestly, it all goes back to building and maintaining an extensible and flexible platform for anywhere engagement. What you’re building today should allow you to rapidly take advantage of whatever unimaginable use cases wait around the corner. ------------------------------------------------------ I hope you enjoyed the brief interview with Brian. It’s really awesome to have such smart and innovation-minded individuals on our Oracle Commerce innovation team. Please join me again in a few weeks for Part 3 of this series where I interview one of the product managers on our team about how the blending of digital and in-store selling in influencing our product development and vision.

    Read the article

  • CodePlex Daily Summary for Sunday, March 18, 2012

    CodePlex Daily Summary for Sunday, March 18, 2012Popular ReleasesRiP-Ripper & PG-Ripper: RiP-Ripper 2.9.28: changes NEW: Added Support for "PixHub.eu" linksSmartNet: V1.0.0.0: DY SmartNet ?????? V1.0callisto: callisto 2.0.21: Added an option to disable local host detection.Javascript .NET: Javascript .NET v0.6: Upgraded to the latest stable branch of v8 (/tags/3.9.18), and switched to using their scons build system. We no longer include v8 source code as part of this project's source code. Simultaneous multithreaded use of v8 now supported (v8 Isolates), although different contexts may not share objects or call each other. 64-bit .Net 4.0 DLL now included. (Download now includes x86 and x64 for both .Net 3.5 and .Net 4.0.)MyRouter (Virtual WiFi Router): MyRouter 1.0.6: This release should be more stable there were a few bug fixes including the x64 issue as well as an error popping up when MyRouter started this was caused by a NULL valuePulse: Pulse Beta 4: This version is still in development but should include: Logging and error handling have been greatly improved. If you run into an error or Pulse crashes make sure to check the Log folder for a recently modified log file so you can report the details of the issue A bunch of new features for the Wallbase.cc provider. Cleaner separation between inputs, downloading and output. Input and downloading are fairly clean now but outputs are still mixed up in the mix which I'm trying to resolve ...Google Books Downloader for Windows: Google Books Downloader-2.0.0.0.: Google Books DownloaderFinestra Virtual Desktops: 2.5.4501: This is a very minor update release. Please see the information about the 2.5 and 2.5.4500 releases for more information on recent changes. This update did not even have an automatic update triggered for it. Adds error checking and reporting to all threads, not only those with message loopsAcDown????? - Anime&Comic Downloader: AcDown????? v3.9.2: ?? ●AcDown??????????、??、??????,????1M,????,????,?????????????????????????。???????????Acfun、????(Bilibili)、??、??、YouTube、??、???、??????、SF????、????????????。??????AcPlay?????,??????、????????????????。 ● AcDown???????????????????????????,???,???????????????????。 ● AcDown???????C#??,????.NET Framework 2.0??。?????"Acfun?????"。 ????32??64? Windows XP/Vista/7/8 ????????????? ??:????????Windows XP???,?????????.NET Framework 2.0???(x86),?????"?????????"??? ??????????????,??????????: ??"AcDo...ArcGIS Editor for OpenStreetMap: ArcGIS Editor for OSM 2.0 Release Candidate: Your feedback is welcome - and this is your last chance to get your fixes in for this version! Includes installer for both Feature Server extension and Desktop extension, enhanced functionality for the Desktop tools, and enhanced built-in Javascript Editor for the Feature Server component. This release candidate includes fixes to beta 4 that accommodate domain users for setting up the Server Component, and fixes for reporting/uploading references tracked in the revision table. See Code In-P...C.B.R. : Comic Book Reader: CBR 0.6: 20 Issue trackers are closed and a lot of bugs too Localize view is now MVVM and delete is working. Added the unused flag (take care that it goes to true only when displaying screen elements) Backstage - new input/output format choice control for the conversion Backstage - Add display, behaviour and register file type options in the extended options dialog Explorer list view has been transformed to a custom control. New group header, colunms order and size are saved Single insta...Windows Azure Toolkit for Windows 8: Windows Azure Toolkit for Windows 8 Consumer Prv: Windows Azure Toolkit for Windows 8 Consumer Preview - Preview Release v1.2.1Minor updates to setup experience: Check for WebPI before install Dependency Check updated to support the following VS 11 and VS 2010 SKUs Ultimate, Premium, Professional and Express Certs Windows Azure Toolkit for Windows 8 Consumer Preview - Preview Release v1.2.0 Please download this for Windows Azure Toolkit for Windows 8 functionality on Windows 8 Consumer Preview. The core features of the toolkit include:...Facebook Graph Toolkit: Facebook Graph Toolkit 3.0: ships with JSON Toolkit v3.0, offering parse speed up to 10 times of last version supports Facebook's new auth dialog supports new extend access token endpoint new example Page Tab app filter Graph Api connections using dates fixed bugs in Page Tab appsCODE Framework: 4.0.20312.0: This version includes significant improvements in the WPF system (and the WPF MVVM/MVC system). This includes new styles for Metro controls and layouts. Improved color handling. It also includes an improved theme/style swapping engine down to active (open) views. There also are various other enhancements and small fixes throughout the entire framework.ScintillaNET: ScintillaNET 2.4: 3/12/2012 Jacob Slusser Added support for annotations. Issues Fixed with this Release Issue # Title 25012 25012 25018 25018 25023 25023 25014 25014 Visual Studio ALM Quick Reference Guidance: v3 - For Visual Studio 11: RELEASE README Welcome to the BETA release of the Quick Reference Guide preview As this is a BETA release and the quality bar for the final Release has not been achieved, we value your candid feedback and recommend that you do not use or deploy these BETA artifacts in a production environment. Quality-Bar Details Documentation has been reviewed by Visual Studio ALM Rangers Documentation has not been through an independent technical review Documentation ...AvalonDock: AvalonDock 2.0.0345: Welcome to early alpha release of AvalonDock 2.0 I've completely rewritten AvalonDock in order to take full advantage of the MVVM pattern. New version also boost a lot of new features: 1) Deep separation between model and layout. 2) Full WPF binding support thanks to unified logical tree between main docking manager, auto-hide windows and floating windows. 3) Support for Aero semi-maximized windows feature. 4) Support for multiple panes in the same floating windows. For a short list of new f...Windows Azure PowerShell Cmdlets: Windows Azure PowerShell Cmdlets 2.2.2: Changes Added Start Menu Item for Easy Startup Added Link to Getting Started Document Added Ability to Persist Subscription Data to Disk Fixed Get-Deployment to not throw on empty slot Simplified numerous default values for cmdlets Breaking Changes: -SubscriptionName is now mandatory in Set-Subscription. -DefaultStorageAccountName and -DefaultStorageAccountKey parameters were removed from Set-Subscription. Instead, when adding multiple accounts to a subscription, each one needs to be added ...IronPython: 2.7.2.1: On behalf of the IronPython team, I'm happy to announce the final release IronPython 2.7.2. This release includes everything from IronPython 54498 and 62475 as well. Like all IronPython 2.7-series releases, .NET 4 is required to install it. Installing this release will replace any existing IronPython 2.7-series installation. Unlike previous releases, the assemblies for all supported platforms are included in the installer as well as the zip package, in the "Platforms" directory. IronPython 2...Kooboo CMS: Kooboo CMS 3.2.0.0: Breaking changes: When upgrade from previous versions, MUST reset the all the content type templates, otherwise the content manager might get a compile error. New features Integrate with Windows azure. See: http://wiki.kooboo.com/?wiki=Kooboo CMS on Azure Complete solution to deploy on load balance servers. See: http://wiki.kooboo.com/?wiki=Kooboo CMS load balance Update Jquery and Jquery ui to the lastest version(Jquery 1.71, Jquery UI 1.8.16). Tree style text content editing. See:h...New Projects4sr4ss1: Assignment 1 WDT Due date: 26 March 2012ADLN: Project to ADLNbook2guest: book2guestBundlingTweaks: BundlingTweaks makes it easier for developers to develop ASP.NET MVC 4 projects with Bundling/Minification support. You can now take advantage of Bundling, but still see non-minified JavaScript when debugging.COBOL SCREENSAVER: This project will show how to create a Windows screen saver using 1) an object-oriented isCOBOL GUI application, 2) an OpenCobol Windows native executable wrapper for the isCOBOL GUI, and 3) XML, XSLT, HTML5, and a Java FX 2.0 web browser component. Release 0.1 consists of a Java GUI application, the OpenCobol wrapper, and a README file detailing usage, system requirements, and installation of the recommended OpenCobol binaries for Windows.Colorado Time System Get CTS Results to Text File: This application will query a Colorado Time System 5, retrieve the lane results by event and heat. These can then be written to a text file.CommonEventLog: This project provides a simple means of logging messages and exceptions to a custom event log.ContainerTrack: Application for tracking container locationContent Widgets Orchard module: This Orchard module makes it possible to add arbitrary widgets to content types (with the option to disable per item).Cup of Badminton: This is a application for draw cup of badminton. You can insert, edit and delete player. You can choose many variant of draw.FSGREE: FSGREEKeepSafety: ??、??、?????????LibGrafx: LibGrafix is a C++ DLL that contains several classes useful when developing computer graphics applications, particularly OpenGL applications, in the Windows environment. It also includes a class that loads and displays the ModelX format exported by the XNA Model Viewer program. Linq to SQL code generator for Windows Phone: Linq to SQL code generator for Windows Phone is an add-in for Visual Studio 2010 or later to generate the Linq to SQL classes from a DBML diagram. Offline Navigation for Windows Phone 7: This is a simple implementation of offline navigation for windows phone 7 with map offset adjustment support.PayrollSystemRedux: Payroll case study book Robert Martin (Agile PPP in C#)PhoneFlipMenu Control for Windows Phone: A control that mimics the behaviour of the Email app's reply/reply all/forward menu.QTscenarist: QTscenarist makes it easier for Synfig animation to create Synfig movies. You can write scenaries and create your movie with it. It's developed in QT. recycle: This is a recycle web pageSharePoint 2010 Accordian Launch: SharePoint 2010 and SharePoint Foundation Quick Launch Accordian Solution.SharePoint 2010 JavaScript Registration Panel: The SharePoint 2010 JavaScript Registration Panel allows you to add JavaScript files to a site collection without SharePoint 2010 Designer intervention. This is helpful in scenarios where SharePoint Designer 2010 is disabled globally, but you have to add some JavaScript files (e.g. jQuery) to your site collection for every page load. The aim of this project is to provide following features: - load JavaScript files on every page load of your site collection - define the sequence for loadi...Sistema de Gestion Escolar: Projecto final monografico universidad dominicana O&MSmartNet: DYSmartNet????????????????????????。???TCP??,??????????,??????????... solution: solution team explorerTanmiaGrp: This is the tanmia base project library.VideoMobileSteraming: Will Update soonXNASter: XNASter is a short library that allows beginner developers to create simple XNA games. Right now it is in the very early stages of development. Included are the following parts: * 2D generic sprite-based object that supports movement, acceleration, etc. In the future, we are also planning to support: * KinectSkeleton controller Together with the project, there are also a few sample games that show how to use it.???WP: HateCoWP is Hatena Coco Client.???: ????????????????????。

    Read the article

  • Microsoft Declares the Future of ASP.NET is Web API

    - by sbwalker
    Sitting on a plane on my way home from Tech Ed 2012 in Orlando, I thought it would be a good time to jot down some key takeaways from this year’s conference. Some of these items I have known since the Microsoft MVP Summit which occurred in Redmond in late February ( but due to NDA restrictions I could not share them with the developer community at large ) and some of them are a result of insightful conversations with a wide variety of industry insiders and Microsoft employees at the conference. First, let’s travel back in time 4 years to the Microsoft MVP Summit in 2008. Microsoft was facing some heat from market newcomer Ruby on Rails and responded with a new web development framework of its own, ASP.NET MVC. At the Summit they estimated that MVC would only be applicable for ~10% of all new web development projects. Based on that prediction I questioned why they were investing such considerable resources for such a relative edge case, but my guess is that they felt it was an important edge case at the time as some of the more vocal .NET evangelists as well as some very high profile start-ups ( ie. Twitter ) had publicly announced their intent to use Rails. Microsoft made a lot of noise about MVC. In fact, they focused so much of their messaging and marketing hype around MVC that it appeared that WebForms was essentially dead. Yes, it may have been true that Microsoft continued to invest in WebForms, but from an outside perspective it really appeared that MVC was the only framework getting any real attention. As a result, MVC started to gain market share. An inside source at Microsoft told me that MVC usage has grown at a rate of about 5% per year and now sits at ~30%. Essentially by focusing so much marketing effort on MVC, Microsoft actually created a larger market demand for it.  This is because in the Microsoft ecosystem there is somewhat of a bandwagon mentality amongst developers. If Microsoft spends a lot of time talking about a specific technology, developers get the perception that it must be really important. So rather than choosing the right tool for the job, they often choose the tool with the most marketing hype and then try to sell it to the customer. In 2010, I blogged about the fact that MVC did not make any business sense for the DotNetNuke platform. This was because our ecosystem relied on third party extensions which were dependent on the WebForms model. If we migrated the core to MVC it would mean that all of the third party extensions would no longer be compatible, which would be an irresponsible business decision for us to make at the expense of our users and customers. However, this did not stop the debate from continuing to occur in our ecosystem. Clearly some developers had drunk Microsoft’s Kool-Aid about MVC and were of the mindset, to paraphrase an old Scottish saying, “If its not MVC, it’s crap”. Now, this is a rather ignorant position to take as most of the benefits of MVC can be achieved in WebForms with solid architecture and responsible coding practices. Clean separation of concerns, unit testing, and direct control over page output are all possible in the WebForms model – it just requires diligence and discipline. So over the past few years some horror stories have begun to bubble to the surface of software development projects focused on ground-up rewrites of web applications for the sole purpose of migrating from WebForms to MVC. These large scale rewrites were typically initiated by engineering teams with only a single argument driving the business decision, that Microsoft was promoting MVC as “the future”. These ill-fated rewrites offered no benefit to end users or customers and in fact resulted in a less stable, less scalable and more complicated systems – basically taking one step forward and two full steps back. A case in point is the announcement earlier this week that a popular open source .NET CMS provider has decided to pull the plug on their new MVC product which has been under active development for more than 18 months and revert back to WebForms. The availability of multiple server-side development models has deeply fragmented the Microsoft developer community. Some folks like to compare it to the age-old VB vs. C# language debate. However, the VB vs. C# language debate was ultimately more of a religious war because at least the two dominant programming languages were compatible with one another and could be used interchangeably. The issue with WebForms vs. MVC is much more challenging. This is because the messaging from Microsoft has positioned the two solutions as being incompatible with one another and as a result web developers feel like they are forced to choose one path or another. Yes, it is true that it has always been technically possible to use WebForms and MVC in the same project, but the tooling support has always made this feel “dirty”. The fragmentation has also made it difficult to attract newcomers as the perceived barrier to entry for learning ASP.NET has become higher. As a result many new software developers entering the market are gravitating to environments where the development model seems more simple and intuitive ( ie. PHP or Ruby ). At the same time that the Web Platform team was busy promoting ASP.NET MVC, the Microsoft Office team has been promoting Sharepoint as a platform for building internal enterprise web applications. Sharepoint has great penetration in the enterprise and over time has been enhanced with improved extensibility capabilities for software developers. But, like many other mature enterprise ASP.NET web applications, it is built on the WebForms development model. Similar to DotNetNuke, Sharepoint leverages a rich third party ecosystem for both generic web controls and more specialized WebParts – both of which rely on WebForms. So basically this resulted in a situation where the Web Platform group had headed off in one direction and the Office team had gone in another direction, and the end customer was stuck in the middle trying to figure out what to do with their existing investments in Microsoft technology. It really emphasized the perception that the left hand was not speaking to the right hand, as strategically speaking there did not seem to be any high level plan from Microsoft to ensure consistency and continuity across the different product lines. With the introduction of ASP.NET MVC, it also made some of the third party control vendors scratch their heads, and wonder what the heck Microsoft was thinking. The original value proposition of ASP.NET over Classic ASP was the ability for web developers to emulate the highly productive desktop development model by using abstract components for creating rich, interactive web interfaces. Web control vendors like Telerik, Infragistics, DevExpress, and ComponentArt had all built sizable businesses offering powerful user interface components to WebForms developers. And even after MVC was introduced these vendors continued to improve their products, offering greater productivity and a superior user experience via AJAX to what was possible in MVC. And since many developers were comfortable and satisfied with these third party solutions, the demand remained strong and the third party web control market continued to prosper despite the availability of MVC. While all of this was going on in the Microsoft ecosystem, there has also been a fundamental shift in the general software development industry. Driven by the explosion of Internet-enabled devices, the focus has now centered on service-oriented architecture (SOA). Service-oriented architecture is all about defining a public API for your product that any client can consume; whether it’s a native application running on a smart phone or tablet, a web browser taking advantage of HTML5 and Javascript, or a rich desktop application running on a PC. REST-based services which utilize the less verbose characteristics of JSON as a transport mechanism, have become the preferred approach over older, more bloated SOAP-based techniques. SOA also has the benefit of producing a cross-platform API, as every major technology stack is able to interact with standard REST-based web services. And for web applications, more and more developers are turning to robust Javascript libraries like JQuery and Knockout for browser-based client-side development techniques for calling web services and rendering content to end users. In fact, traditional server-side page rendering has largely fallen out of favor, resulting in decreased demand for server-side frameworks like Ruby on Rails, WebForms, and (gasp) MVC. In response to these new industry trends, Microsoft did what it always does – it immediately poured some resources into developing a solution which will ensure they remain relevant and competitive in the web space. This work culminated in a new framework which was branded as Web API. It is convention-based and designed to embrace native HTTP standards without copious layers of abstraction. This framework is designed to be the ultimate replacement for both the REST aspects of WCF and ASP.NET MVC Web Services. And since it was developed out of band with a dependency only on ASP.NET 4.0, it means that it can be used immediately in a variety of production scenarios. So at Tech Ed 2012 it was made abundantly clear in numerous sessions that Microsoft views Web API as the “Future of ASP.NET”. In fact, one Microsoft PM even went as far as to say that if we look 3-4 years into the future, that all ASP.NET web applications will be developed using the Web API approach. This is a fairly bold prediction and clearly telegraphs where Microsoft plans to allocate its resources going forward. Currently Web API is being delivered as part of the MVC4 package, but this is only temporary for the sake of convenience. It also sounds like there are still internal discussions going on in terms of how to brand the various aspects of ASP.NET going forward – perhaps the moniker of “ASP.NET Web Stack” coined a couple years ago by Scott Hanselman and utilized as part of the open source release of ASP.NET bits on Codeplex a few months back will eventually stick. Web API is being positioned as the unification of ASP.NET – the glue that is able to pull this fragmented mess back together again. The  “One ASP.NET” strategy will promote the use of all frameworks - WebForms, MVC, and Web API, even within the same web project. Basically the message is utilize the appropriate aspects of each framework to solve your business problems. Instead of navigating developers to a fork in the road, the plan is to educate them that “hybrid” applications are a great strategy for delivering solutions to customers. In addition, the service-oriented approach coupled with client-side development promoted by Web API can effectively be used in both WebForms and MVC applications. So this means it is also relevant to application platforms like DotNetNuke and Sharepoint, which means that it starts to create a unified development strategy across all ASP.NET product lines once again. And so what about MVC? There have actually been rumors floated that MVC has reached a stage of maturity where, similar to WebForms, it will be treated more as a maintenance product line going forward ( MVC4 may in fact be the last significant iteration of this framework ). This may sound alarming to some folks who have recently adopted MVC but it really shouldn’t, as both WebForms and MVC will continue to play a vital role in delivering solutions to customers. They will just not be the primary area where Microsoft is spending the majority of its R&D resources. That distinction will obviously go to Web API. And when the question comes up of why not enhance MVC to make it work with Web API, you must take a step back and look at this from the higher level to see that it really makes no sense. MVC is a server-side page compositing framework; whereas, Web API promotes client-side page compositing with a heavy focus on web services. In order to make MVC work well with Web API, would require a complete rewrite of MVC and at the end of the day, there would be no upgrade path for existing MVC applications. So it really does not make much business sense. So what does this have to do with DotNetNuke? Well, around 8-12 months ago we recognized the software industry trends towards web services and client-side development. We decided to utilize a “hybrid” model which would provide compatibility for existing modules while at the same time provide a bridge for developers who wanted to utilize more modern web techniques. Customers who like the productivity and familiarity of WebForms can continue to build custom modules using the traditional approach. However, in DotNetNuke 6.2 we also introduced a new Service Framework which is actually built on top of MVC2 ( we chose to leverage MVC because it had the most intuitive, light-weight REST implementation in the .NET stack ). The Services Framework allowed us to build some rich interactive features in DotNetNuke 6.2, including the Messaging and Notification Center and Activity Feed. But based on where we know Microsoft is heading, it makes sense for the next major version of DotNetNuke ( which is expected to be released in Q4 2012 ) to migrate from MVC2 to Web API. This will likely result in some breaking changes in the Services Framework but we feel it is the best approach for ensuring the platform remains highly modern and relevant. The fact that our development strategy is perfectly aligned with the “One ASP.NET” strategy from Microsoft means that our customers and developer community can be confident in their current and future investments in the DotNetNuke platform.

    Read the article

  • When gaming computer freezes with a blank screen and a buzzing sound

    - by The Colour Of Heartache
    I have a problem with random freezes when playing games. Sometimes it's fine for hours, other times it dosn't last even one. I tried googling around and I found recomendations to update my graphics drivers and to test for overheating. The graphics drivers haven't helped worked and Furmark created a consistant heat higher than I get during a crash. I even tried running a game using the Linux dual boot and WINE, that crashed too. Here are the tempreture logs leading up to the latest crash. The GPU dosn't hit 80, and I've hit 90 with no crash on firmark. DATE TIME MHz CPU_0 CPU_1 CPU_2 CPU_3 LOAD% GPU 04/05/12 15:21:00 3200.16 63 58 57 56 15.4 77 04/05/12 15:21:05 3200.16 63 59 58 56 15.8 76 04/05/12 15:21:10 3200.16 62 59 58 55 15.1 78 04/05/12 15:21:15 3200.16 63 59 58 56 16.5 77 04/05/12 15:21:20 3200.16 64 58 58 57 15.3 77 04/05/12 15:21:25 3200.16 63 58 59 56 15.8 78 04/05/12 15:21:30 3200.16 63 58 58 57 15.8 77 04/05/12 15:21:35 3200.16 63 58 58 56 17.0 77 04/05/12 15:21:40 3200.16 63 59 59 56 15.9 77 04/05/12 15:21:45 3200.16 63 58 58 58 15.6 77 04/05/12 15:21:50 3200.16 63 58 58 58 15.8 77 04/05/12 15:21:55 3200.16 63 58 59 56 15.9 77 04/05/12 15:22:00 3200.16 63 58 58 57 15.8 77 04/05/12 15:21:05 3200.16 63 58 58 56 15.9 77 04/05/12 15:21:10 3200.16 63 57 58 56 15.3 78 04/05/12 15:21:15 3200.16 64 58 58 56 15.4 78 04/05/12 15:21:20 3200.16 63 58 58 56 15.4 77 04/05/12 15:21:25 3200.16 62 58 58 57 15.6 77 04/05/12 15:21:30 3200.16 62 58 58 57 15.8 77 04/05/12 15:21:35 3200.16 63 59 58 56 15.9 77 04/05/12 15:21:40 3200.16 63 58 58 56 15.9 77 04/05/12 15:21:45 3200.16 63 59 58 56 15.6 77 04/05/12 15:21:50 3200.16 62 59 58 58 15.8 77 04/05/12 15:21:55 3200.16 63 58 58 57 15.9 77 04/05/12 15:22:00 3200.16 63 58 58 56 15.9 77 04/05/12 15:22:05 3200.16 63 58 58 56 16.3 77 04/05/12 15:22:10 3200.16 64 58 59 56 15.7 77 04/05/12 15:22:15 3200.16 63 58 60 57 17.2 77 04/05/12 15:22:20 3200.16 63 58 58 56 15.5 78 04/05/12 15:22:25 3200.16 63 58 60 57 15.9 77 04/05/12 15:22:30 3200.16 63 59 59 57 15.6 76 04/05/12 15:22:35 3200.16 64 59 60 57 17.7 77 04/05/12 15:22:40 3200.16 63 59 58 57 16.0 77 04/05/12 15:22:45 3200.16 64 58 58 57 15.8 77 04/05/12 15:22:50 3200.16 63 59 58 56 15.8 77 04/05/12 15:22:55 3200.16 63 58 59 57 15.8 78 04/05/12 15:23:00 3200.16 63 59 58 57 15.7 77 04/05/12 15:22:05 3200.16 62 58 57 58 15.9 77 04/05/12 15:22:10 3200.16 63 58 59 57 15.9 77 04/05/12 15:22:15 3200.16 63 59 58 56 17.1 77 04/05/12 15:22:20 3200.16 63 58 59 57 16.0 77 04/05/12 15:22:25 3200.16 63 58 58 57 15.9 77 04/05/12 15:22:30 3200.16 63 59 59 57 15.7 77 04/05/12 15:22:35 3200.16 64 59 58 58 21.0 77 04/05/12 15:22:40 3200.16 63 59 58 58 16.0 77 04/05/12 15:22:45 3200.16 64 59 59 57 15.7 77 04/05/12 15:22:50 3200.16 63 59 58 56 15.8 78 04/05/12 15:22:55 3200.16 63 59 58 57 15.8 78 04/05/12 15:23:00 3200.16 63 59 57 57 15.9 77 04/05/12 15:23:05 3200.16 64 58 58 58 15.7 77 04/05/12 15:23:10 3200.16 63 59 58 56 15.9 77 04/05/12 15:23:15 3200.16 64 59 58 57 16.6 77 04/05/12 15:23:20 3200.16 63 59 58 58 16.0 77 04/05/12 15:23:25 3200.16 63 58 58 57 15.7 77 04/05/12 15:23:30 3200.16 63 59 58 56 15.4 78 04/05/12 15:23:35 3200.16 64 60 59 61 17.7 77 04/05/12 15:23:40 3200.16 63 59 58 57 15.6 77 04/05/12 15:23:45 1600.08 53 54 53 52 4.4 76 04/05/12 15:23:50 3200.16 63 59 57 56 15.8 77 04/05/12 15:23:55 3200.16 63 58 57 57 15.6 77 04/05/12 15:24:00 3200.16 63 58 58 58 15.9 77 04/05/12 15:23:05 3200.16 64 59 58 56 15.6 77 04/05/12 15:23:10 3200.16 64 59 58 57 15.9 77 04/05/12 15:23:15 3200.16 63 59 58 59 16.7 77 04/05/12 15:23:20 3200.16 64 58 58 58 16.0 77 04/05/12 15:23:25 3200.16 64 58 58 57 15.7 77 04/05/12 15:23:30 3200.16 64 58 58 57 15.2 78 04/05/12 15:23:35 3200.16 63 59 59 58 17.8 77 04/05/12 15:23:40 3200.16 63 59 59 58 15.8 77 04/05/12 15:23:45 1600.08 53 54 53 52 4.7 76 04/05/12 15:23:50 3200.16 63 59 57 56 16.9 77 04/05/12 15:23:55 3200.16 63 58 59 56 15.7 77 04/05/12 15:24:00 3200.16 63 58 59 57 15.9 77 I also got a dmp file, here's what BlueScreenView gave me. The first three lines were in red, the summery says that the crash was casued by hal.dll and the address hal.dll+12903 Filename Address in Stack From Address To Address Size Time Stamp Time String Product Name File Description File Version Company Full Path hal.dll hal.dll+12903 fffff800`033e0000 fffff800`03429000 0x00049000 0x4a5bdf08 14/07/2009 02:27:36 ntoskrnl.exe ntoskrnl.exe+185923 fffff800`02e05000 fffff800`033e0000 0x005db000 0x4ec7a284 19/11/2011 13:35:16 Microsoft® Windows® Operating System NT Kernel & System 6.1.7600.16917 (win7_gdr.111118-2330) Microsoft Corporation C:\Windows\system32\ntoskrnl.exe pci.sys pci.sys+9aff fffff880`0108f000 fffff880`010c2000 0x00033000 0x4a5bc117 14/07/2009 00:19:51 kdcom.dll fffff800`00bc4000 fffff800`00bce000 0x0000a000 0x4d4d40d9 05/02/2011 13:21:45 mcupdate_GenuineIntel.dll fffff880`00c26000 fffff880`00c6a000 0x00044000 0x4a5bdf66 14/07/2009 02:29:10 PSHED.dll fffff880`00c6a000 fffff880`00c7e000 0x00014000 0x4a5be027 14/07/2009 02:32:23 Microsoft® Windows® Operating System Platform Specific Hardware Error Driver 6.1.7600.16385 (win7_rtm.090713-1255) Microsoft Corporation C:\Windows\system32\PSHED.dll CLFS.SYS fffff880`00c7e000 fffff880`00cdc000 0x0005e000 0x4a5bc11d 14/07/2009 00:19:57 CI.dll fffff880`00cdc000 fffff880`00d9c000 0x000c0000 0x4a5be01d 14/07/2009 02:32:13 Wdf01000.sys fffff880`00e0e000 fffff880`00eb2000 0x000a4000 0x4a5bc19f 14/07/2009 00:22:07 WDFLDR.SYS fffff880`00eb2000 fffff880`00ec1000 0x0000f000 0x4a5bc11a 14/07/2009 00:19:54 sptd.sys fffff880`00ec1000 fffff880`00fe7000 0x00126000 0x4ad24632 11/10/2009 21:55:14 WMILIB.SYS fffff880`00fe7000 fffff880`00ff0000 0x00009000 0x4a5bc117 14/07/2009 00:19:51 SCSIPORT.SYS fffff880`00d9c000 fffff880`00dcb000 0x0002f000 0x4a5bcac0 14/07/2009 01:01:04 ACPI.sys fffff880`01021000 fffff880`01078000 0x00057000 0x4a5bc106 14/07/2009 00:19:34 msisadrv.sys fffff880`01078000 fffff880`01082000 0x0000a000 0x4a5bc0fe 14/07/2009 00:19:26 vdrvroot.sys fffff880`01082000 fffff880`0108f000 0x0000d000 0x4a5bcadb 14/07/2009 01:01:31 partmgr.sys fffff880`010c2000 fffff880`010d7000 0x00015000 0x4a5bc11e 14/07/2009 00:19:58 volmgr.sys fffff880`010d7000 fffff880`010ec000 0x00015000 0x4a5bc11d 14/07/2009 00:19:57 volmgrx.sys fffff880`010ec000 fffff880`01148000 0x0005c000 0x4a5bc141 14/07/2009 00:20:33 pciide.sys fffff880`01148000 fffff880`0114f000 0x00007000 0x4a5bc115 14/07/2009 00:19:49 PCIIDEX.SYS fffff880`0114f000 fffff880`0115f000 0x00010000 0x4a5bc114 14/07/2009 00:19:48 mountmgr.sys fffff880`0115f000 fffff880`01179000 0x0001a000 0x4a5bc11a 14/07/2009 00:19:54 atapi.sys fffff880`01179000 fffff880`01182000 0x00009000 0x4a5bc113 14/07/2009 00:19:47 ataport.SYS fffff880`01182000 fffff880`011ac000 0x0002a000 0x4a5bc118 14/07/2009 00:19:52 msahci.sys fffff880`011ac000 fffff880`011b7000 0x0000b000 0x4a5bcabd 14/07/2009 01:01:01 amdxata.sys fffff880`011b7000 fffff880`011c2000 0x0000b000 0x4ba3a3ca 19/03/2010 17:18:18 fltmgr.sys fffff880`01211000 fffff880`0125d000 0x0004c000 0x4a5bc11f 14/07/2009 00:19:59 fileinfo.sys fffff880`0125d000 fffff880`01271000 0x00014000 0x4a5bc481 14/07/2009 00:34:25 Ntfs.sys fffff880`0145c000 fffff880`015fe000 0x001a2000 0x4d79996d 11/03/2011 04:39:25 msrpc.sys fffff880`01271000 fffff880`012cf000 0x0005e000 0x4a5bc17c 14/07/2009 00:21:32 ksecdd.sys fffff880`01400000 fffff880`0141a000 0x0001a000 0x4ec48579 17/11/2011 04:54:33 cng.sys fffff880`012cf000 fffff880`01342000 0x00073000 0x4ec48cfb 17/11/2011 05:26:35 pcw.sys fffff880`0141a000 fffff880`0142b000 0x00011000 0x4a5bc0ff 14/07/2009 00:19:27 Fs_Rec.sys fffff880`0142b000 fffff880`01435000 0x0000a000 0x4a5bc111 14/07/2009 00:19:45 ndis.sys fffff880`01653000 fffff880`01745000 0x000f2000 0x4a5bc184 14/07/2009 00:21:40 NETIO.SYS fffff880`01745000 fffff880`017a5000 0x00060000 0x4bbe946f 09/04/2010 03:43:59 ksecpkg.sys fffff880`017a5000 fffff880`017d0000 0x0002b000 0x4ec48d32 17/11/2011 05:27:30 tcpip.sys fffff880`01802000 fffff880`01a00000 0x001fe000 0x4e83eb7f 29/09/2011 04:52:31 fwpkclnt.sys fffff880`01600000 fffff880`0164a000 0x0004a000 0x4a5bc164 14/07/2009 00:21:08 vmstorfl.sys fffff880`017d0000 fffff880`017e0000 0x00010000 0x4a5bc67e 14/07/2009 00:42:54 volsnap.sys fffff880`01342000 fffff880`0138e000 0x0004c000 0x4a5bc128 14/07/2009 00:20:08 spldr.sys fffff880`017e0000 fffff880`017e8000 0x00008000 0x4a0858bb 11/05/2009 17:56:27 rdyboost.sys fffff880`0138e000 fffff880`013c8000 0x0003a000 0x4a5bc48a 14/07/2009 00:34:34 mup.sys fffff880`017e8000 fffff880`017fa000 0x00012000 0x4a5bc201 14/07/2009 00:23:45 hwpolicy.sys fffff880`0164a000 fffff880`01653000 0x00009000 0x4a5bc0fa 14/07/2009 00:19:22 fvevol.sys fffff880`011c2000 fffff880`011fc000 0x0003a000 0x4abd7db2 26/09/2009 03:34:26 disk.sys fffff880`01435000 fffff880`0144b000 0x00016000 0x4a5bc11d 14/07/2009 00:19:57 CLASSPNP.SYS fffff880`013c8000 fffff880`013f8000 0x00030000 0x4a5bc11e 14/07/2009 00:19:58 cdrom.sys fffff880`00dcb000 fffff880`00df5000 0x0002a000 0x4a5bc11a 14/07/2009 00:19:54 MpFilter.sys fffff880`02c1a000 fffff880`02c4b000 0x00031000 0x4d9cc801 06/04/2011 21:07:29 Null.SYS fffff880`02c4b000 fffff880`02c54000 0x00009000 0x4a5bc109 14/07/2009 00:19:37 Beep.SYS fffff880`02c54000 fffff880`02c5b000 0x00007000 0x4a5bca8d 14/07/2009 01:00:13 vga.sys fffff880`02c5b000 fffff880`02c69000 0x0000e000 0x4a5bc587 14/07/2009 00:38:47 VIDEOPRT.SYS fffff880`02c69000 fffff880`02c8e000 0x00025000 0x4a5bc58b 14/07/2009 00:38:51 watchdog.sys fffff880`02c8e000 fffff880`02c9e000 0x00010000 0x4a5bc53f 14/07/2009 00:37:35 RDPCDD.sys fffff880`02c9e000 fffff880`02ca7000 0x00009000 0x4a5bce62 14/07/2009 01:16:34 rdpencdd.sys fffff880`02ca7000 fffff880`02cb0000 0x00009000 0x4a5bce62 14/07/2009 01:16:34 rdprefmp.sys fffff880`02cb0000 fffff880`02cb9000 0x00009000 0x4a5bce63 14/07/2009 01:16:35 Msfs.SYS fffff880`02cb9000 fffff880`02cc4000 0x0000b000 0x4a5bc113 14/07/2009 00:19:47 Npfs.SYS fffff880`02cc4000 fffff880`02cd5000 0x00011000 0x4a5bc114 14/07/2009 00:19:48 tdx.sys fffff880`02cd5000 fffff880`02cf3000 0x0001e000 0x4a5bc16b 14/07/2009 00:21:15 TDI.SYS fffff880`02cf3000 fffff880`02d00000 0x0000d000 0x4a5bc16e 14/07/2009 00:21:18 afd.sys fffff880`02d00000 fffff880`02d89000 0x00089000 0x4efa940c 28/12/2011 04:59:08 netbt.sys fffff880`02d89000 fffff880`02dce000 0x00045000 0x4a5bc178 14/07/2009 00:21:28 ws2ifsl.sys fffff880`02dce000 fffff880`02dd9000 0x0000b000 0x4a5bccf9 14/07/2009 01:10:33 wfplwf.sys fffff880`02dd9000 fffff880`02de2000 0x00009000 0x4a5bccb6 14/07/2009 01:09:26 pacer.sys fffff880`00c00000 fffff880`00c26000 0x00026000 0x4a5bccc5 14/07/2009 01:09:41 vpcnfltr.sys fffff880`02de2000 fffff880`02df6000 0x00014000 0x4ab97aae 23/09/2009 02:32:30 netbios.sys fffff880`02c00000 fffff880`02c0f000 0x0000f000 0x4a5bccb6 14/07/2009 01:09:26 serial.sys fffff880`04075000 fffff880`04092000 0x0001d000 0x4a5bcaa8 14/07/2009 01:00:40 wanarp.sys fffff880`04092000 fffff880`040ad000 0x0001b000 0x4a5bcced 14/07/2009 01:10:21 vpcvmm.sys fffff880`040ad000 fffff880`04103180 0x00056180 0x4ab97ab6 23/09/2009 02:32:38 termdd.sys fffff880`04104000 fffff880`04118000 0x00014000 0x4a5bce64 14/07/2009 01:16:36 rdbss.sys fffff880`04118000 fffff880`04169000 0x00051000 0x4a5bc219 14/07/2009 00:24:09 nsiproxy.sys fffff880`04169000 fffff880`04175000 0x0000c000 0x4a5bc15e 14/07/2009 00:21:02 mssmbios.sys fffff880`04175000 fffff880`04180000 0x0000b000 0x4a5bc3be 14/07/2009 00:31:10 discache.sys fffff880`04180000 fffff880`0418f000 0x0000f000 0x4a5bc52e 14/07/2009 00:37:18 csc.sys fffff880`04280000 fffff880`04303000 0x00083000 0x4a5bc22a 14/07/2009 00:24:26 dfsc.sys fffff880`04303000 fffff880`04321000 0x0001e000 0x4db78623 27/04/2011 03:57:39 blbdrive.sys fffff880`04321000 fffff880`04332000 0x00011000 0x4a5bc4df 14/07/2009 00:35:59 tunnel.sys fffff880`04332000 fffff880`04358000 0x00026000 0x4a5bccc1 14/07/2009 01:09:37 intelppm.sys fffff880`04358000 fffff880`0436e000 0x00016000 0x4a5bc0fd 14/07/2009 00:19:25 nvlddmkm.sys fffff880`0fe34000 fffff880`10b52000 0x00d1e000 0x4f4e68c4 29/02/2012 19:04:52 nvBridge.kmd fffff880`10b52000 fffff880`10b53180 0x00001180 0x4d27c482 08/01/2011 02:57:22 dxgkrnl.sys fffff880`04450000 fffff880`04544000 0x000f4000 0x4d3fa1a0 26/01/2011 05:22:56 dxgmms1.sys fffff880`04544000 fffff880`0458a000 0x00046000 0x4d3fa174 26/01/2011 05:22:12 usbuhci.sys fffff880`0458a000 fffff880`04597000 0x0000d000 0x4d8c0a8f 25/03/2011 04:22:55 USBPORT.SYS fffff880`04597000 fffff880`045ed000 0x00056000 0x4d8c0a97 25/03/2011 04:23:03 usbehci.sys fffff880`045ed000 fffff880`045fe000 0x00011000 0x4d8c0a91 25/03/2011 04:22:57 HDAudBus.sys fffff880`04400000 fffff880`04424000 0x00024000 0x4a5bcbf5 14/07/2009 01:06:13 1394ohci.sys fffff880`10b54000 fffff880`10b92000 0x0003e000 0x4a5bcc30 14/07/2009 01:07:12 Rt64win7.sys fffff880`10b92000 fffff880`10bc4000 0x00032000 0x49a65b0d 26/02/2009 10:04:13 i8042prt.sys fffff880`04424000 fffff880`04442000 0x0001e000 0x4a5bc11d 14/07/2009 00:19:57 kbdclass.sys fffff880`10bc4000 fffff880`10bd3000 0x0000f000 0x4a5bc116 14/07/2009 00:19:50 VMkbd.sys fffff880`04442000 fffff880`0444d000 0x0000b000 0x4b5a836f 23/01/2010 06:04:47 serenum.sys fffff880`10bd3000 fffff880`10bdf000 0x0000c000 0x4a5bcaa1 14/07/2009 01:00:33 av1shsvl.SYS fffff880`0436e000 fffff880`043b3000 0x00045000 0x4a5cf4d7 14/07/2009 22:12:55 wmiacpi.sys fffff880`10bdf000 fffff880`10be8000 0x00009000 0x4a5bc3b6 14/07/2009 00:31:02 CompositeBus.sys fffff880`10be8000 fffff880`10bf8000 0x00010000 0x4a5bcaa1 14/07/2009 01:00:33 AgileVpn.sys fffff880`0fe00000 fffff880`0fe16000 0x00016000 0x4a5bccf0 14/07/2009 01:10:24 rasl2tp.sys fffff880`043b3000 fffff880`043d7000 0x00024000 0x4a5bcce3 14/07/2009 01:10:11 ndistapi.sys fffff880`0fe16000 fffff880`0fe22000 0x0000c000 0x4a5bccd8 14/07/2009 01:10:00 ndiswan.sys fffff880`04200000 fffff880`0422f000 0x0002f000 0x4a5bcce3 14/07/2009 01:10:11 raspppoe.sys fffff880`0422f000 fffff880`0424a000 0x0001b000 0x4a5bcce9 14/07/2009 01:10:17 raspptp.sys fffff880`0424a000 fffff880`0426b000 0x00021000 0x4a5bccea 14/07/2009 01:10:18 rassstp.sys fffff880`043d7000 fffff880`043f1000 0x0001a000 0x4a5bccf1 14/07/2009 01:10:25 tapoas.sys fffff880`0fe22000 fffff880`0fe2f000 0x0000d000 0x4c3a627f 12/07/2010 01:31:59 tap0901.sys fffff880`043f1000 fffff880`043fe000 0x0000d000 0x4b22da33 12/12/2009 00:48:03 rdpbus.sys fffff880`0426b000 fffff880`04276000 0x0000b000 0x4a5bceaa 14/07/2009 01:17:46 mouclass.sys fffff880`0418f000 fffff880`0419e000 0x0000f000 0x4a5bc116 14/07/2009 00:19:50 swenum.sys fffff880`0444d000 fffff880`0444e480 0x00001480 0x4a5bca92 14/07/2009 01:00:18 ks.sys fffff880`0419e000 fffff880`041e1000 0x00043000 0x4b8f37d9 04/03/2010 05:32:25 umbus.sys fffff880`041e1000 fffff880`041f3000 0x00012000 0x4a5bcc20 14/07/2009 01:06:56 vpcusb.sys fffff880`04000000 fffff880`0401d000 0x0001d000 0x4ab97ab7 23/09/2009 02:32:39 usbrpm.sys fffff880`0401d000 fffff880`0402c000 0x0000f000 0x4a5bd2c2 14/07/2009 01:35:14 USBD.SYS fffff880`045fe000 fffff880`045fff00 0x00001f00 0x4d8c0a8b 25/03/2011 04:22:51 vmnetadapter.sys fffff880`10bf8000 fffff880`10c00000 0x00008000 0x4a800ce5 10/08/2009 13:04:53 VMNET.SYS fffff880`04276000 fffff880`04280000 0x0000a000 0x4a800ce2 10/08/2009 13:04:50 vpchbus.sys fffff880`0402c000 fffff880`04068000 0x0003c000 0x4ab97ab0 23/09/2009 02:32:32 usbhub.sys fffff880`04c26000 fffff880`04c80000 0x0005a000 0x4d8c0aaa 25/03/2011 04:23:22 NDProxy.SYS fffff880`04c80000 fffff880`04c95000 0x00015000 0x4a5bccdd 14/07/2009 01:10:05 HdAudio.sys fffff880`04c95000 fffff880`04cf1000 0x0005c000 0x4a5bcc23 14/07/2009 01:06:59 portcls.sys fffff880`04cf1000 fffff880`04d2e000 0x0003d000 0x4a5bcc03 14/07/2009 01:06:27 drmk.sys fffff880`04d2e000 fffff880`04d50000 0x00022000 0x4a5bd8e5 14/07/2009 02:01:25 ksthunk.sys fffff880`04d50000 fffff880`04d55200 0x00005200 0x4a5bca93 14/07/2009 01:00:19 win32k.sys fffff960`000c0000 fffff960`003d4000 0x00314000 0x00000000 Dxapi.sys fffff880`04d56000 fffff880`04d62000 0x0000c000 0x4a5bc574 14/07/2009 00:38:28 udfs.sys fffff880`04d62000 fffff880`04db6000 0x00054000 0x4a5bc1f9 14/07/2009 00:23:37 monitor.sys fffff880`04db6000 fffff880`04dc4000 0x0000e000 0x4a5bc58c 14/07/2009 00:38:52 TSDDD.dll fffff960`004c0000 fffff960`004ca000 0x0000a000 0x00000000 hidusb.sys fffff880`04dc4000 fffff880`04dd2000 0x0000e000 0x4a5bcbfe 14/07/2009 01:06:22 HIDCLASS.SYS fffff880`04dd2000 fffff880`04deb000 0x00019000 0x4a5bcbfd 14/07/2009 01:06:21 HIDPARSE.SYS fffff880`04deb000 fffff880`04df3080 0x00008080 0x4a5bcbf9 14/07/2009 01:06:17 cdd.dll fffff960`00660000 fffff960`00687000 0x00027000 0x00000000 mouhid.sys fffff880`04c00000 fffff880`04c0d000 0x0000d000 0x4a5bca94 14/07/2009 01:00:20 luafv.sys fffff880`05a78000 fffff880`05a9b000 0x00023000 0x4a5bc295 14/07/2009 00:26:13 WudfPf.sys fffff880`05a9b000 fffff880`05abc000 0x00021000 0x4a5bcbd1 14/07/2009 01:05:37 crashdmp.sys fffff880`05abc000 fffff880`05aca000 0x0000e000 0x4a5bcabd 14/07/2009 01:01:01 dump_dumpata.sys fffff880`05aca000 fffff880`05ad6000 0x0000c000 0x4a5bc113 14/07/2009 00:19:47 dump_msahci.sys fffff880`05ad6000 fffff880`05ae1000 0x0000b000 0x4a5bcabd 14/07/2009 01:01:01 dump_dumpfve.sys fffff880`05ae1000 fffff880`05af4000 0x00013000 0x4a5bc18f 14/07/2009 00:21:51 vmnetbridge.sys fffff880`05af4000 fffff880`05b04000 0x00010000 0x4a800d26 10/08/2009 13:05:58 lltdio.sys fffff880`05b04000 fffff880`05b19000 0x00015000 0x4a5bcc92 14/07/2009 01:08:50 rspndr.sys fffff880`05b19000 fffff880`05b31000 0x00018000 0x4a5bcc92 14/07/2009 01:08:50 HTTP.sys fffff880`05b31000 fffff880`05bf9000 0x000c8000 0x4a5bc1a8 14/07/2009 00:22:16 bowser.sys fffff880`05a00000 fffff880`05a1e000 0x0001e000 0x4d6497da 23/02/2011 06:15:06 mpsdrv.sys fffff880`05a1e000 fffff880`05a36000 0x00018000 0x4a5bcc79 14/07/2009 01:08:25 mrxsmb.sys fffff880`05a36000 fffff880`05a63000 0x0002d000 0x4dc0bf1a 04/05/2011 03:51:06 mrxsmb10.sys fffff880`066ce000 fffff880`0671c000 0x0004e000 0x4e17c0a7 09/07/2011 03:44:55 mrxsmb20.sys fffff880`0671c000 fffff880`0673f000 0x00023000 0x4dc0bf19 04/05/2011 03:51:05 hcmon.sys fffff880`0673f000 fffff880`0674b000 0x0000c000 0x4b5a765b 23/01/2010 05:08:59 vmci.sys fffff880`0674b000 fffff880`06763000 0x00018000 0x4b5a6e03 23/01/2010 04:33:23 vmx86.sys fffff880`06896000 fffff880`0696c000 0x000d6000 0x4b5a8e0d 23/01/2010 06:50:05 MpNWMon.sys fffff880`0696c000 fffff880`0697c000 0x00010000 0x4d9cc7fb 06/04/2011 21:07:23 peauth.sys fffff880`06600000 fffff880`066a6000 0x000a6000 0x4a5bd8df 14/07/2009 02:01:19 secdrv.SYS fffff880`0697c000 fffff880`06987000 0x0000b000 0x4508052e 13/09/2006 14:18:38 srvnet.sys fffff880`06987000 fffff880`069b4000 0x0002d000 0x4dba2ca3 29/04/2011 04:12:35 tcpipreg.sys fffff880`069b4000 fffff880`069c6000 0x00012000 0x4a5bcccd 14/07/2009 01:09:49 vmnetuserif.sys fffff880`069c6000 fffff880`069d0000 0x0000a000 0x4b5a7a6b 23/01/2010 05:26:19 vstor2-mntapi10.sys fffff880`069d0000 fffff880`069dc000 0x0000c000 0x49e94462 18/04/2009 04:09:22 vstor2-ws60.sys fffff880`069dc000 fffff880`069e8000 0x0000c000 0x4ad39a52 12/10/2009 22:06:26 srv2.sys fffff880`06800000 fffff880`06867000 0x00067000 0x4dba2cb3 29/04/2011 04:12:51 srv.sys fffff880`06763000 fffff880`067f8000 0x00095000 0x4dba2cc1 29/04/2011 04:13:05 NisDrvWFP.sys fffff880`06867000 fffff880`0687f000 0x00018000 0x4d9cc855 06/04/2011 21:08:53 WinRing0x64.sys fffff880`0687f000 fffff880`06886000 0x00007000 0x488b26c1 26/07/2008 14:29:37 asyncmac.sys fffff880`0aa8f000 fffff880`0aa9a000 0x0000b000 0x4a5bcce5 14/07/2009 01:10:13 nvoclk64.sys fffff880`0aa9a000 fffff880`0aaaa000 0x00010000 0x4ab00e3d 15/09/2009 22:59:25 I'd apreciate any help because I'm well outside of my comfort zone.

    Read the article

  • Right div pushing center div further down

    - by Chase
    I cannot get this last div to go up properly in my layout and have tried countless things. I'm not sure what's going on with my css? Here is a screenshot: http://img291.imageshack.us/img291/5377/screenshot20100528at123.png #events { float: left; width: 420px; margin:0 0 5px 0; font-family:Helvetica, Arial, sans-serif; font-size: 16px; background-image: url(images/lastfmhead.jpg); background-repeat: no-repeat; height:360px; overflow:hidden; display: inline; } #events table { width:419px; } #events th, td { padding: 3px 3px; } #whatsup ul, #citywhatsup ul { margin:0 5px 0 5px; text-align:left; font-family:Helvetica, Arial, sans-serif; } #whatsup ul li, #citywhatsup ul li{ list-style-type:none; list-style: none; } #whatsup hr, #citywhatsup hr{ border: none 0; border-top: 1px dashed #990000;/*the border*/ width: 100%; height: 1px; margin: 1px auto 5px auto;/*whatever the total width of the border-top and border-bottom equal*/ } #events ul { margin:5px 5px 0 5px; } #events ul li{ list-style-type:none; list-style: none; } #attending ul { display: inline-block; margin: 0; width:200px; } #attending ul li { display: inline-block; list-style-image:none; margin:0; padding:2px 5px 2px 5px; } #attending { width: 230px; margin:0 13px 5px 12px; float: left; display: inline; background-image: url(images/otherhead.jpg); background-repeat: no-repeat; text-align:center; height:360px; overflow:hidden; } #whatsup { width: 230px; margin:0 0 5px 0; float: left; display:inline; background-image: url(images/otherhead.jpg); background-repeat: no-repeat; text-align:center; } #eventtitle{ margin: 3px 0 -3px 0; } #eventtitle { color: #900; margin-left: 5px; font-size:16px; } #tweetit { color: #487B96 !important; font-size:16px; margin: 3px 0 -4px 0; } #photos { background-image: url(images/flickrheader.jpg); background-repeat: no-repeat; width: 665px; clear:both; } <div id="cityevents"> <h2> Events </h2> <table> <th>Date </th><th> Who's Playing </th><th> Venue </th><th> City </th><th> Tickets </th> <tr><td>May 28</td><td><a href='http://www.songkick.com/concerts/5384486?utm_source=1121&utm_medium=partner' target='_blank'>Jill King</a></td><td>Open Eye Cafe</td><td>Carrboro</td><td style='text-align:center;'><span style='color: #999'> Find </span></td></tr><tr><td>May 28</td><td><a href='http://www.songkick.com/concerts/5281141?utm_source=1121&utm_medium=partner' target='_blank'>Ahleuchatistas</a></td><td>Nightlight</td><td>Chapel Hill</td><td style='text-align:center;'><span style='color: #999'> Find </span></td></tr><tr><td>May 28</td><td><a href='http://www.songkick.com/concerts/4970896?utm_source=1121&utm_medium=partner' target='_blank'>Sam Quinn</a></td><td>Local 506</td><td>Chapel Hill</td><td style='text-align:center;'><span style='color: #999'> Find </span></td></tr><tr><td>May 29</td><td><a href='http://www.songkick.com/concerts/5303661?utm_source=1121&utm_medium=partner' target='_blank'>Cagematch Mayhem, Champion Vs Au Jus, Heartbreaker Vs Au Jus</a></td><td>DSI Comedy Theater</td><td>Carrboro</td><td style='text-align:center;'><a href='http://www.songkick.com/concerts/5303661/tickets?utm_source=1121&utm_medium=partner' target='_blank'> Find </a></td></tr><tr><td>May 29</td><td><a href='http://www.songkick.com/concerts/4722066?utm_source=1121&utm_medium=partner' target='_blank'>Lewd Acts, Converge, Gaza, Black Breath</a></td><td>Cat's Cradle</td><td>Carrboro</td><td style='text-align:center;'><a href='http://www.songkick.com/concerts/4722066/tickets?utm_source=1121&utm_medium=partner' target='_blank'> Find </a></td></tr><tr><td>May 29</td><td><a href='http://www.songkick.com/concerts/4647076?utm_source=1121&utm_medium=partner' target='_blank'>Nate Currin</a></td><td>Broad Street Cafe</td><td>Durham</td><td style='text-align:center;'><span style='color: #999'> Find </span></td></tr><tr><td>May 29</td><td><a href='http://www.songkick.com/concerts/5580211?utm_source=1121&utm_medium=partner' target='_blank'>International Night</a></td><td>Serena Rtp</td><td>Durham</td><td style='text-align:center;'><a href='http://www.songkick.com/concerts/5580211/tickets?utm_source=1121&utm_medium=partner' target='_blank'> Find </a></td></tr><tr><td>May 29</td><td><a href='http://www.songkick.com/concerts/4770241?utm_source=1121&utm_medium=partner' target='_blank'>Jill King</a></td><td>Caffe Driade</td><td>Chapel Hill</td><td style='text-align:center;'><span style='color: #999'> Find </span></td></tr><tr><td>May 29</td><td><a href='http://www.songkick.com/concerts/5406411?utm_source=1121&utm_medium=partner' target='_blank'>Sunbears!</a></td><td>Local 506</td><td>Chapel Hill</td><td style='text-align:center;'><span style='color: #999'> Find </span></td></tr><tr><td>May 29</td><td><a href='http://www.songkick.com/concerts/4924136?utm_source=1121&utm_medium=partner' target='_blank'>Studio Gangsters</a></td><td>The Reservoir</td><td>Carrboro</td><td style='text-align:center;'><span style='color: #999'> Find </span></td></tr><tr><td>May 30</td><td><a href='http://www.songkick.com/concerts/5252161?utm_source=1121&utm_medium=partner' target='_blank'>She Wants Revenge</a></td><td>Cat's Cradle</td><td>Carrboro</td><td style='text-align:center;'><span style='color: #999'> Find </span></td></tr><tr><td>May 30</td><td><a href='http://www.songkick.com/concerts/4436326?utm_source=1121&utm_medium=partner' target='_blank'>Unheard Radio Battle of the Bands</a></td><td>Mansion 462</td><td>Chapel Hill</td><td style='text-align:center;'><a href='http://www.songkick.com/concerts/4436326/tickets?utm_source=1121&utm_medium=partner' target='_blank'> Find </a></td></tr><tr><td>May 30</td><td><a href='http://www.songkick.com/concerts/4924141?utm_source=1121&utm_medium=partner' target='_blank'>Studio Gangsters</a></td><td>The Cave</td><td>Chapel Hill</td><td style='text-align:center;'><span style='color: #999'> Find </span></td></tr><tr><td>Jun 2</td><td><a href='http://www.songkick.com/concerts/5252881?utm_source=1121&utm_medium=partner' target='_blank'>Jeanne Jolly</a></td><td>Caffe Driade</td><td>Chapel Hill</td><td style='text-align:center;'><span style='color: #999'> Find </span></td></tr><tr><td>Jun 2</td><td><a href='http://www.songkick.com/concerts/4628026?utm_source=1121&utm_medium=partner' target='_blank'>James Husband, Of Montreal</a></td><td>Cat's Cradle</td><td>Carrboro</td><td style='text-align:center;'><a href='http://www.songkick.com/concerts/4628026/tickets?utm_source=1121&utm_medium=partner' target='_blank'> Find </a></td></tr><tr><td>Jun 2</td><td><a href='http://www.songkick.com/concerts/5019466?utm_source=1121&utm_medium=partner' target='_blank'>Camera Obscura</a></td><td>Duke Gardens</td><td>Durham</td><td style='text-align:center;'><a href='http://www.songkick.com/concerts/5019466/tickets?utm_source=1121&utm_medium=partner' target='_blank'> Find </a></td></tr><tr><td>Jun 3</td><td><a href='http://www.songkick.com/concerts/4226511?utm_source=1121&utm_medium=partner' target='_blank'>Reverend Horton Heat, Cracker, Legendary Shack Shakers</a></td><td>Cat's Cradle</td><td>Carrboro</td><td style='text-align:center;'><a href='http://www.songkick.com/concerts/4226511/tickets?utm_source=1121&utm_medium=partner' target='_blank'> Find </a></td></tr><tr><td>Jun 3</td><td><a href='http://www.songkick.com/concerts/5253371?utm_source=1121&utm_medium=partner' target='_blank'>American Aquarium</a></td><td>Local 506</td><td>Chapel Hill</td><td style='text-align:center;'><span style='color: #999'> Find </span></td></tr><tr><td>Jun 4</td><td><a href='http://www.songkick.com/concerts/4285251?utm_source=1121&utm_medium=partner' target='_blank'>Laurence Juber</a></td><td>The ArtsCenter</td><td>Carrboro</td><td style='text-align:center;'><span style='color: #999'> Find </span></td></tr><tr><td>Jun 4</td><td><a href='http://www.songkick.com/concerts/5642566?utm_source=1121&utm_medium=partner' target='_blank'>Community Jam, Pt Scarborough Is a Movie, Armageddon'it</a></td><td>DSI Comedy Theater</td><td>Carrboro</td><td style='text-align:center;'><a href='http://www.songkick.com/concerts/5642566/tickets?utm_source=1121&utm_medium=partner' target='_blank'> Find </a></td></tr><tr><td>Jun 4</td><td><a href='http://www.songkick.com/concerts/4676216?utm_source=1121&utm_medium=partner' target='_blank'>Big Bill Morganfield</a></td><td>Papa Mojos Roadhouse</td><td>Durham</td><td style='text-align:center;'><span style='color: #999'> Find </span></td></tr> </table> </div> <!-- Events --> <div id="citywhatsup"> <h2> What's Up? <div id="tweetit"><a class="btn-slide">Tell em'</a> </div></h2> <div id="twitpanel"></div> <script type="text/javascript"> twttr.anywhere(function (T) { T("#twitpanel").tweetBox({ height: 100, width: 215, label: '', defaultContent: "" }); }); </script> <script type="text/javascript"> twttr.anywhere(function (T) { T("#whatsup").linkifyUsers(); }); </script> <ul> <li><img src='http://a1.twimg.com/profile_images/898693876/4604414396_0464180430_b_normal.jpg' alt='kaiten_keiku' height=40px; width=40px; style='border:0px; float: left; padding-right:4px;'/> @kaiten_keiku: <span style='text-align:justify;'>@Charlotte_Nao ????????~?????????!</span> - <span class='twittertime'>May 28 12:37AM</span></li><hr/><li><img src='http://a3.twimg.com/profile_images/612153581/bowdown_normal.jpg' alt='bugn' height=40px; width=40px; style='border:0px; float: left; padding-right:4px;'/> @bugn: <span style='text-align:justify;'>@Bravotv (sitc2 as rhony) Bethenny-Carrie, Sonja-Samantha, Alex-Miranda, Ramona-Charlotte</span> - <span class='twittertime'>May 28 12:36AM</span></li><hr/><li><img src='http://a1.twimg.com/profile_images/844630278/mj_normal.jpg' alt='Myra_Jones' height=40px; width=40px; style='border:0px; float: left; padding-right:4px;'/> @Myra_Jones: <span style='text-align:justify;'>@t_weet123 If you're still in Charlotte then you need to head to Whiskey River...they say Luke B. just walked in and started drinking.</span> - <span class='twittertime'>May 28 12:36AM</span></li><hr/><li><img src='http://a1.twimg.com/profile_images/936667468/110971230_normal.jpg' alt='THEORACLE2' height=40px; width=40px; style='border:0px; float: left; padding-right:4px;'/> @THEORACLE2: <span style='text-align:justify;'>@MsKamilah08 are yall in charlotte?</span> - <span class='twittertime'>May 28 12:36AM</span></li><hr/><li><img src='http://a1.twimg.com/profile_images/767244842/7AM_normal.jpg' alt='mtollefsrud' height=40px; width=40px; style='border:0px; float: left; padding-right:4px;'/> @mtollefsrud: <span style='text-align:justify;'>@vosler09 thinks I'm Charlotte.</span> - <span class='twittertime'>May 28 12:36AM</span></li><hr/><li><img src='http://a3.twimg.com/profile_images/936496517/DSCF0317_-_Copy_normal.JPG' alt='Thasian' height=40px; width=40px; style='border:0px; float: left; padding-right:4px;'/> @Thasian: <span style='text-align:justify;'>I like #CharMeck #Charlotte | Atlanta = #No #FAIL #EPICFAIL</span> - <span class='twittertime'>May 28 12:36AM</span></li><hr/><li><img src='http://a3.twimg.com/profile_images/695551715/NASCAR_logo_flag_normal.jpg' alt='NascarNewsNow' height=40px; width=40px; style='border:0px; float: left; padding-right:4px;'/> @NascarNewsNow: <span style='text-align:justify;'>#NASCAR #RACING News from the track: Charlotte Motor Speedway | Nascar Leath: Ahh, the waiting is... http://bit.ly/b2DToq #NHRA #DAYTONA500</span> - <span class='twittertime'>May 28 12:35AM</span></li> </ul> </div> <div id="photos"> <h2> Recent Photos </h2> <ul> <li><a href='http://farm5.static.flickr.com/4029/4646832962_980f936db9.jpg' target='_blank' rel='lightbox-photos' title='05 23 10 Jamie's Baby Shower 097'><img src='http://farm5.static.flickr.com/4029/4646832962_980f936db9_t.jpg' alt='05 23 10 Jamie's Baby Shower 097' height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://farm4.static.flickr.com/3176/4646218481_d06829a778.jpg' target='_blank' rel='lightbox-photos' title='summer'><img src='http://farm4.static.flickr.com/3176/4646218481_d06829a778_t.jpg' alt='summer' height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://farm5.static.flickr.com/4032/4646833312_7b1de5390a.jpg' target='_blank' rel='lightbox-photos' title='100_0064'><img src='http://farm5.static.flickr.com/4032/4646833312_7b1de5390a_t.jpg' alt='100_0064' height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://farm5.static.flickr.com/4008/4646832834_784a0a9ed1.jpg' target='_blank' rel='lightbox-photos' title=''><img src='http://farm5.static.flickr.com/4008/4646832834_784a0a9ed1_t.jpg' alt='' height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://farm5.static.flickr.com/4066/4646218735_b37d8fd9e5.jpg' target='_blank' rel='lightbox-photos' title='DSC05524'><img src='http://farm5.static.flickr.com/4066/4646218735_b37d8fd9e5_t.jpg' alt='DSC05524' height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://farm5.static.flickr.com/4054/4646830604_97afd54623.jpg' target='_blank' rel='lightbox-photos' title='DTLA graff'><img src='http://farm5.static.flickr.com/4054/4646830604_97afd54623_t.jpg' alt='DTLA graff' height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://farm5.static.flickr.com/4066/4646833048_7a9ab28733.jpg' target='_blank' rel='lightbox-photos' title='100_0243.jpg'><img src='http://farm5.static.flickr.com/4066/4646833048_7a9ab28733_t.jpg' alt='100_0243.jpg' height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://farm4.static.flickr.com/3399/4646832626_de89d0fb0e.jpg' target='_blank' rel='lightbox-photos' title='6W????'><img src='http://farm4.static.flickr.com/3399/4646832626_de89d0fb0e_t.jpg' alt='6W????' height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://farm5.static.flickr.com/4005/4646832826_0d9e8afe19.jpg' target='_blank' rel='lightbox-photos' title='IMG_9381'><img src='http://farm5.static.flickr.com/4005/4646832826_0d9e8afe19_t.jpg' alt='IMG_9381' height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://farm5.static.flickr.com/4046/4646830752_dfc32b1740.jpg' target='_blank' rel='lightbox-photos' title='11'><img src='http://farm5.static.flickr.com/4046/4646830752_dfc32b1740_t.jpg' alt='11' height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://farm5.static.flickr.com/4010/4646215929_80b78f0007.jpg' target='_blank' rel='lightbox-photos' title='GEDC8592'><img src='http://farm5.static.flickr.com/4010/4646215929_80b78f0007_t.jpg' alt='GEDC8592' height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://farm5.static.flickr.com/4064/4646832384_7fc8d31e11.jpg' target='_blank' rel='lightbox-photos' title='2010 Advanced Grappling'><img src='http://farm5.static.flickr.com/4064/4646832384_7fc8d31e11_t.jpg' alt='2010 Advanced Grappling' height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://farm5.static.flickr.com/4049/4646218143_c108276325.jpg' target='_blank' rel='lightbox-photos' title='P1270352'><img src='http://farm5.static.flickr.com/4049/4646218143_c108276325_t.jpg' alt='P1270352' height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://farm5.static.flickr.com/4009/4646217767_3900f39475.jpg' target='_blank' rel='lightbox-photos' title='P1270351'><img src='http://farm5.static.flickr.com/4009/4646217767_3900f39475_t.jpg' alt='P1270351' height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://farm5.static.flickr.com/4027/4646831284_30b6e6da36.jpg' target='_blank' rel='lightbox-photos' title='Image245'><img src='http://farm5.static.flickr.com/4027/4646831284_30b6e6da36_t.jpg' alt='Image245' height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://farm4.static.flickr.com/3399/4646218295_63a899d322.jpg' target='_blank' rel='lightbox-photos' title='IMG_0037'><img src='http://farm4.static.flickr.com/3399/4646218295_63a899d322_t.jpg' alt='IMG_0037' height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://farm5.static.flickr.com/4059/4646218159_01d5b02c3f.jpg' target='_blank' rel='lightbox-photos' title='DooDah2010-6665'><img src='http://farm5.static.flickr.com/4059/4646218159_01d5b02c3f_t.jpg' alt='DooDah2010-6665' height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://farm5.static.flickr.com/4053/4646834404_615e09b715.jpg' target='_blank' rel='lightbox-photos' title='IMG_2668'><img src='http://farm5.static.flickr.com/4053/4646834404_615e09b715_t.jpg' alt='IMG_2668' height=100px; width=100px; style='border:0px;'/></a></li> </ul> </div> <div id="videos"> <h2> Recent Videos </h2> <ul> <li><a href='http://www.youtube.com/watch?v=_oc5-0yFoYg&feature=youtube_gdata' target='_blank'><img src='http://i.ytimg.com/vi/_oc5-0yFoYg/default.jpg'height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://www.youtube.com/watch?v=1pRXKeYVYHc&feature=youtube_gdata' target='_blank'><img src='http://i.ytimg.com/vi/1pRXKeYVYHc/default.jpg'height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://www.youtube.com/watch?v=yzRQUu-ZBdw&feature=youtube_gdata' target='_blank'><img src='http://i.ytimg.com/vi/yzRQUu-ZBdw/default.jpg'height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://www.youtube.com/watch?v=mud-A76nLro&feature=youtube_gdata' target='_blank'><img src='http://i.ytimg.com/vi/mud-A76nLro/default.jpg'height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://www.youtube.com/watch?v=TLOboW19_OA&feature=youtube_gdata' target='_blank'><img src='http://i.ytimg.com/vi/TLOboW19_OA/default.jpg'height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://www.youtube.com/watch?v=PcYja2jjvi0&feature=youtube_gdata' target='_blank'><img src='http://i.ytimg.com/vi/PcYja2jjvi0/default.jpg'height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://www.youtube.com/watch?v=KKjklCEMrPk&feature=youtube_gdata' target='_blank'><img src='http://i.ytimg.com/vi/KKjklCEMrPk/default.jpg'height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://www.youtube.com/watch?v=AyUwY6PRX0Y&feature=youtube_gdata' target='_blank'><img src='http://i.ytimg.com/vi/AyUwY6PRX0Y/default.jpg'height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://www.youtube.com/watch?v=8Sf2-7RjVYs&feature=youtube_gdata' target='_blank'><img src='http://i.ytimg.com/vi/8Sf2-7RjVYs/default.jpg'height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://www.youtube.com/watch?v=xGMayoJmhE8&feature=youtube_gdata' target='_blank'><img src='http://i.ytimg.com/vi/xGMayoJmhE8/default.jpg'height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://www.youtube.com/watch?v=paseBeB6Cb8&feature=youtube_gdata' target='_blank'><img src='http://i.ytimg.com/vi/paseBeB6Cb8/default.jpg'height=100px; width=100px; style='border:0px;'/></a></li><li><a href='http://www.youtube.com/watch?v=l_FSRUtMMik&feature=youtube_gdata' target='_blank'><img src='http://i.ytimg.com/vi/l_FSRUtMMik/default.jpg'height=100px; width=100px; style='border:0px;'/></a></li> </ul> </div> </div><!-- #content -->

    Read the article

< Previous Page | 8 9 10 11 12