Search Results

Search found 5109 results on 205 pages for 'playing cards'.

Page 120/205 | < Previous Page | 116 117 118 119 120 121 122 123 124 125 126 127  | Next Page >

• Proper approach to debug PC startup problems (POST)

  - by saurabhj

  My CPU was heating up to around 65 deg C and last time this had happened (about a year ago), I got thermal paste put between the CPU and heat sink and this managed to get it down to about 45 - 50 degrees. This time, I got some thermal paste and put it myself. However, my PC is not showing the POST display and not starting up. This is what happens LEDs light up HDDs spin Mouse is getting power All fans including the processor fan starts No display on monitor No diagnostic beep sounds (no sounds at all) What I have tried Removing everything including RAM, HDD, PCI cards, AGP card Boot up machine No changes from first state. What steps can I take to figure out where the problem lies? Note (might be important) When I removed the heat sink, the processor came out with it (it was stuck to it inspite of the processor latch on) Had to pry it separate with a screw-driver. Configuration Pentium 4, 2.8 Ghz with HT (very old, I know) Original Intel Mobo with onboard sound and graphics (GB series) 2x512 Mb DDR-RAM 2 SATA disks (320 Gigs / 250 gigs) DVD Writer Creative Sound Card Network card Any help would be appreciated. Thanks!

  Read the article

• The sound freezes while listening to music

  - by Scott

  I have bought an sound card - Sound Blaster X-FI Surround 5.1 PRO and while I'm listening to the music, after few minutes or even hours (it does happends randomly) the sound dissapears and I have to go settings: Playing Devices - Advanced and switch the Default Format (sampling frequency) and switch from the `16-bits, 48000 Hz (DVD Quality) to any other from the list (16-bits, 96000 Hz or 24-bits, 48000 Hz or 24-bits 96000 Hz). I have been trying to set all of the above options, but for all of them the sound freezes after listening to music. It is getting annoying and I hope its the settings fault and not my sound card. I got my drivers installed from the attached CD and I'm running Windows 7 HP 64 bits. If anyone would try to help me, I would really appreciate this.

  Read the article

• Can a processor upgrade cause BSOD?

  - by Daniel

  I Had the following hardware setup: Phenom II X4 945 Asus M4A97 4GB DDR2 OCZ Radeon HD5850 OCZ Agility 2 120 GB Windows 7 x64 Pro Fully updated (latest drivers and windows update patches) Then I bought an used Phenom II X6 1090T and installed it without formatting. Since that my computer started BSODing almost every time I'm playing any game and with different error messages, like: page fault in non-paged area bad pool header the video memory manager found a problem error in dxgmm1.sys(or something like that) And when it doesn't BSOD the game simply crashes. I have tried: Updating BIOS Reseting BIOS to defaults Reinstalling Video Drivers Installing the latest DirectX All that's left is to do a full format and I don't want to do that since it's going to be a lot of work to fine tune windows to my preferences again. So is my "new" processor defective or do I really need to format the computer? Update: I use a (properly installed) custom cooler from Coolermaster and both the BIOS and the Open Hardware Monitor(Application) attest the CPU is not overheating, so I guess the CPU its defective and since I bought it from a guy over the Internet I'm probably screwed

  Read the article

• Ubuntu 10.10 - PC shutdown before boot shortly after BIOS loads

  - by clem

  Hi - Since installing Ubuntu 10.10 from Karmic I've started getting problems with starting up the PC. I've done a complete wipe (Boot and Nuke) of the hard drive and reinstalled Ubuntu 10.10 but the problem still occurs. There is no dual boot on the PC, just Ubuntu. Here is the problem: Each morning, when I turn the PC on from being off overnight, the PC starts up and loads the BIOS. I get the following message : "Verifying DMI Pool Data... K8 NPT Data Change...Update New Data to DMI!....... Then poof the computer shuts off. However, after switching the computer back on around 6 or 7 times after it's turned itself off, it will eventually boot up without any problem. Also, once up and running for a while, I can shutdown and restart the PC first time, without any issues. I have also noticed a problem with the USB mouse being recognised and once I finally get the computer booted up, I need to unplug and then plug the mouse back in to get it working. I've opened the PC up and checked the connections (cables, cards and memory) and it all seems fine. The main issue with troubleshooting this problem is I cannot test any suggestions or fixes until the next morning because once the computer is up and running it will remain so! I do not leave the computer on overnight to save energy. So.. is this a hardware / boot software issue? This is a very odd problem and I have googled to no avail. Any suggestions? Many thanks Clem

  Read the article

• Problem accessing the remote working space on my new SBS 2008 box

  - by Dabblernl

  This supposedly easy to install OS is starting to drive me nuts... SYMPTOMS: When trying to connect to the remote workplace I get (and ignore) the security warning because I am currently testing with the self issued certificate. After loggin in the remote workplace's main screen displays but the images on it do not load. When I try to click the email link I am thrown back to the login screen. If I try the login to exchange directly by typing in the remote.mydomain.com/owa address I get a 403 error that I am denied access. The problem occurs on both a vista and a win 7 machine. It seems that some security setting is playing tricks with me. How can I troubleshoot this?

  Read the article

• Sorting Files into Subfolders based on EXIF Date

  - by honestor

  I have a huge directory from a HDD recovery that contains 70000+ JPEG files. I tried playing around with some AppleScripts, that I found, but had no luck. I already installed EXIFtool, which might be useful for this task. The current directory structure is as follows: dir001 - file0001.jpg ... - file9999.jpg dir002 - file0001.jpg ... - file9999.jpg ... dir070 - file0001.jpg - ... - file9999.jpg The files mostly have EXIF Data, but sometimes there are Files without metadata. Now I hope to be able to sort and rename these files into folders based on the date: 1999 - 1999 01 31 - 1999_01_31_-_22_59_59.jpg 2000 - 2000 05 20 - 2000_05_20_-_21_59_59.jpg - 2000_05_20_-_22_59_59.jpg I figured Applescript/Automator might come in handy for this, however every other solution would be welcome, too!

  Read the article

• How do I trap the mouse pointer within a VirtualBox Guest OS?

  - by Samuel

  I'm on a Mac Mini 2011 with VirtualBox installed. I have Windows 7 running as a Guest OS. My question: How do I "trap" my mouse pointer within Windows? In other words, I don't want my mouse to move outside to the Host OS. Ideally, I would be able to press the Host key to "untrap" my mouse. The purpose: I'm playing Warcraft 3 in the Guest OS and I can't scroll the screen since the mouse keeps jumping to the Host OS instead of scrolling the screen. This happens even in full-screen mode.

  Read the article

• Security Token for Mac/Linux/Windows, self-managed, pref. open source?

  - by DevelopersDevelopersDevelopers

  I'm looking to buy an evaluation security token (combined smart card/usb reader) for my business that works on: Windows 7 x64 OS X 10.6.x x64 Ubuntu Linux (64 or 32 bit, 10.04 or 10.10, I can bend based on possible tokens) Functionality I need is: Login authentication Authentication for whole-disk encryption (in Linux/Windows, Mac is flexible here) Signing/encryption using PGP and x.509 certificates RSA-2048 key-capable (1024 not good enough.) I can manage the certificates myself Open source middleware/drivers (not necessarily FOSS, just source available. Can flex on this, I just want to be able to audit the code. OpenSC-compatible on Linux would be great.) Is there any token that can do all of this? Or would I need multiple ones to accomplish this? Or do I need to look at smart cards and readers to get this? I have been researching this for a while and have had a heck of a time even getting accurate information about products. Also, I am in the USA, and it appears that EU export laws prevent me from buying from there, so those vendors are out. I was looking at Feitian tokens from Gooze, but since they are in France I can't buy.

  Read the article

• Sudden "No Signal" in HDMI-DVI connection

  - by nazikus

  Yesterday I have connected external display Asus VW192C to my laptop Dell XPS 14-L421X via HDMI-to-DVI-D cable. And it worked perfectly fine from start. The day after, Asus screen went blank showing "No signal". Every time I connection/disconnection cable or power off/on the display it says "No signal". And I didn't change any system configurations meanwhile. To troubleshoot the problem, I have tried to connect laptop to TV (hdmi-to-hdmi) - it was fine. I've tried to connect a different laptop to the display via the same cable - worked fine as well. So its obviously something on system level, either Windows or graphics drivers. Also it seems that Windows still see the external display (I can move mouse pointer away from the main screen in Extended mode), but there's just no signal. Any ideas? What else to try? PS. My laptop has 2 graphics cards - GeForce 630M and Intel HD 4000 using NVidia Optimus technology. I have updated to latest Intel and NVidia drivers, still didn't help. PPS. Although I shouldn't have updated (from Intel support): "our Intel generic graphics drivers from the Intel website do not support using both Intel Graphics 4000 and NVidia GeForece GT630M". Nevertheless, it should not affect connectivity to additional display.

  Read the article

• Best practice for administering a (hadoop) cluster

  - by Alex

  Dear all, I've recently been playing with Hadoop. I have a six node cluster up and running - with HDFS, and having run a number of MapRed jobs. So far, so good. However I'm now looking to do this more systematically and with a larger number of nodes. Our base system is Ubuntu and the current setup has been administered using apt (to install the correct java runtime) and ssh/scp (to propagate out the various conf files). This is clearly not scalable over time. Does anyone have any experience of good systems for administering (possibly slightly heterogenous: different disk sizes, different numbers of cpus on each node) hadoop clusters automagically? I would consider diskless boot - but imagine that with a large cluster, getting the cluster up and running might be bottle-necked on the machine serving the OS. Or some form of distributed debian apt to keep the machines native environment synchronised? And how do people successfully manage the conf files over a number of (potentially heterogenous) machines? Thanks very much in advance, Alex

  Read the article

• Outlook 2003 won't send mail

  - by RKid

  A colleague's e-mail has just started playing up - he's using Outlook/Office 2003 on a Win XP SP3 machine. Yesterday his mail has suddenly stopped being received, although there are no errors of any kind that i can see. It was only noticed because he didn't have any replys all day. His e-mails seem to send fine - no errors come up, the mail goes into Sent Items as usual, but it never arrives at it's destination. However, when mail is sent from Outlook Web Access, e-mails send fine. All connections to the server appear fine and outlook is 'connected' but I've had a look at the message tracking on our Exchange 2003 server and no messages are appearing when sent from outlook, only when sent through OWA. Where should i be looking ? Thanks.

  Read the article

• Start ELEVATED script from within script

  - by Ulrich

  Hallo, I'm playing around with Powershell (relative NewBie) and I'm looking for the easiest way to call a Powershell script with elevated rights from within another script. I know of the runas verb for start-process which allows me to start a new script with a different account. My problem is, however, that under Vista (UAC active) every admin account has two access tokens, a normal privilege one and an elevated one. If I use the runas method, the second scripts gets started under the right account but with the non-elevated access token. Is there an easy way to control this? Thanks a lot for your help! Ulrich

  Read the article

• How to find dom0 name from hosted domU

  - by svigan

  I'm actually testing RHEL 5.3 with Xen between two servers in order to have a disaster recovery solution. So I'm playing with moving my domU from one dom0 server to the other server. Unfortunatly when somebody else move the domU I don't have any clue where my domain is hosted. I'm wondering where I can't find my dom0 name with inside domU. I'm looking for something like the gzonename command on a solaris sparse zone. I check inside /proc/xen but I don't see anything special except the dom0 kernel release. Does anybody know a wait to find this ?

  Read the article

• SharePoint 2010 MySites - Host on separate servers

  - by Chris W

  We're playing with the SP 2010 Beta ahead of a planned deployment later this year in an academic environment. We anticipate that the majority of traffic will be through MySites when everything is provisioned so we're looking at how we can plan our SP topology to scale nicely. An initial thought is to run the main portal on one server, host "Student" MySites on one server and "Staff" on another. Is it acutally possible to do this easily or are we going down a bad path? Specifically - can we have 2 different MySites site collections, each hosted on a dedicated server? If so, can we configure SharePoint to work out from the users's logon account type of user they are and route them to the correct server?

  Read the article

• Synergy configuration with multiple X screens

  - by Rob Drimmie

  I'm having a problem figuring out how to configure synergy to behave on a system with multiple X windows. On my desktop I am running Ubuntu 10.04 LTS. I have two monitors, setup as separate X screens by preference as well as to enable me to rotate the left-hand monitor. I also have a laptop, which I have on the desk in front of me, lower than the other two monitors. I have a very simple synergy.conf: section: screens desktop: laptop.local: end section: links desktop: down = laptop laptop: up = desktop end It works, but on the desktop only on whichever screen I run synergys from in terminal (I haven't set it up to run at startup yet because I've been playing with the configuration). I can't find any information how to reference multiple screens on one system, and would appreciate any help.

  Read the article

• Network tries to reindentify itself now and then

  - by Don Young

  When the computer starts up it connects itself to the router (ZTE 4G router) automatically, but after I have surfed the web for a while, it tries to identify itself, meaning you get that little blue circle next to the little screen at the corner. When browsing it does not cause any problems, but if I'm streaming a video the video will then stop, I'll have to refresh the page to make the video start again. And if I'm playing a game, LoL for example, the game will freeze for about 2 seconds then continue again (due to lost connection to the internet). I have no virus on my computer, although I had before. I have reset my router, restarted my computer, updated my ethernet driver, checked so that the IPv4 is set on automatic and tried different router channels. I have had this router for a few months and the problem just started recently. Here is the ipconfig screen:

  Read the article

• Bypass insane corporate security system

  - by user1665154

  I'm searching for a posibility to bypass the "Firewall" for 3-4 days. I've tried everything I know, so I ask here for a answer. We have no admin rights and the OS is Windows Vista There is an HTTP Proxy with NTML Authentication (only way to access the internet) It requires a username and password We use smart cards, in fact I have only a user number and a pin. Port 80 and 443 are open - I have an SSH server at home which is listening on port 443 The problem is that I need this proxy to connect to anything. Internet access only works in IE, Chrome, Firefox when I set the proxy settings to "use system proxy settings", "proxy-autoconfig (proxy.pac)" or when I enter the proxy inside the proxy.pac file. However I can't understand where they take the username and password which the Proxy requires. What I've tried was using cntlm to connect to the proxy with authentication (altought I have no PW and username) and PuTTY to create the SSH tunnel over port 443 whit the SOCKS Proxy which I've created with cntml. I've never found some SSH client which includes a "use system proxy settings" function.

  Read the article

• How to play multiple videos side-by-side synchronized?

  - by Don Salva

  I've got 3 videos, all 3 have the same time, same amount of frames, and they only differ in terms of encoding quality. Now I need them to run side-by-side in synchronized fashion for evaluation purposes. Meaning when I press "play" BOTH! videos should start. Analogically for stop, forward, backward. Anyone know any player capable of doing that? By that I mean playing more than 1 video side-by-side... Platform: Win7

  Read the article

• Restrict only some plugins to specific sites in Google Chrome

  - by Christian

  I am looking for a way to set up Google Chrome so that it will run a certain plug-in (Java, what else?) only on whitelisted sites, but other plug-ins (like the PDF viewer) everywhere. From playing with the policies available for Chrome, I think there are basically two levels of plug-in management: List of disabled plugins/enabled plugins: Controls whether a plug-in exists for the browser at all This pair of policies applies to plug-ins, but not to sites. Default plug-in settings/Allow plug-ins on sites: Controls on which sites plug-ins can run This set of policies applies to sites, but not to individual plugins, and it cannot override the first pair. There appears to be no way to configure Chrome so that some plug-ins only run on whitelisted sites, but others run everywhere by default. I have also looked at filtering content on the firewall/proxy level, but I'm not convinced it can be done securely there. Filtering by URLs (file names) or content types can be circumvented trivially, and identification by content inspection cannot be safe either.

  Read the article

• Recovered video files won't play

  - by BioGeek

  I have an SD card with pictures and video which malfunctioned. I was able to recover the files with Photorec. The pictures are OK, but wen I try to open the vide files (*.mov extension) in get the following errors when I try to open them in the following programs Windows Media player: "Windows Media Player encountered a problem while playing the file" Quicktime: "Error -2048: Couldn't open the file because it is not a file that QuickTime understands" VLC: it shows the first frame of the video and the sound is just white noise The filesizes look correct so I presume the data is still in there. Is there any way to fix these recovered video files?

  Read the article

• Clean installation of RHEL 5.5 claims package "desktops" is missing

  - by TKguru42

  Hi all, I'm a student worker in the CS department of my university, so please forgive me for any unprofessional descriptions. Simplified explanations are appreciated. I recently replaced some bad graphics cards in a few public workstations. The machines are all the same model. Before putting them back on the network I did fresh installs of RHEL---first I tried 5.4, but yum update ran into all sorts of ugly dependency errors and if I tried to remove any of the problematic packages, the whole operating system FUBAR'd. Using RHEL 5.5 gave me the same errors during install saying that "java.1.5.1-sun*" and "desktops" were missing, but yum update didn't have any dependency problems. Now that I tried logging in through the GUI, I encounter no GUI past the standard RHEL login page. The desktop is a uniform light teal and there's no system tray. An xclock window and an xterm window are open, and Firefox opens automatically, but that's it. Nothing else. What's REALLY confusing is that the computer claims that gnome is already installed, except it clearly isn't working. Any help or advice is greatly appreciated. If it helps, our department uses kickstart to run our standard Linux installs. I can try to get the script if that would be of use. Thank you!

  Read the article

• Windows freezes, showing a random color or pattern

  - by Manu

  I have a PC with windows 7, and I'm experiencing random freezes with increasing frequency. After some time (from 30 minutes to a few hours) the screen will shows a random color or pattern (vertical lines) and nothing works anymore, I need to reboot manually. I've checked the events log, but nothing is shown except for the unexpected reboot. I've tested the RAM with Memtest86+ 4.20, and the graphics card with FurMark 1.10.3, no errors have been found. I've updated the graphic drivers and openned the case to remove dust, but the issue is still there. Also, the problem doesn't seem to arise when I'm playing games fullscreen, but when I'm surfing the web, using itunes, or coding. My hardware is as follows : intel core i5 750 CPU, ATI Radeon HD 5670 graphics card, ASUSTeK P7P55D motherboard, two 2Gb KINGSTON DDR3 ram sticks, 2 SATA hard drives, a Netgear dongle for wifi.

  Read the article

• Windows 7 does not detect my new hard drive?

  - by jasondavis

  I just built a really nice new PC. Some specs... Intel i7-930 CPU ASRock Extreme X58 motherboard with sata 3 and USB 3.0 12gb of G-Skill DDR3 RAM 80gb Intel G2 Solid state drive for Windows 7 and other programs to run on Windows 7 Pro 64bit OS 2 1gb grapghic cards for 4 monitor support Thats the main components. Well today my new 1tb western digital hard drive came which I plan to use for data to preserve the life of my SSD (hopefully). I hooked up it's sata power input and then hooked up it's sata data cable to a sata 2 port on my motherboard, I boot windows 7 and go into my computer and the drive is not showing up with my other drives. I then re-boot again and check again, no luck. I then shut down the PC and open the case back up, I then check my connections and they all look good. I then boot up and I can see the new HD is on and spinning. I then go into my BIOS settings to see if it registers there and it DOES! It shows I have a WD 1tb hard drvie on sata 2 port 6. So I am at a loss of why it is not showing up as an option in windows? Windows acts as if the drive is not there. Please help

  Read the article

• Options not available anymore in my Samsung 932bw lcd

  - by Sávio Mendes

  I think a friend messed up something in my monitor. I left him playing a game and when i came back, i noticed that the brightness was very high. I tried to change it but i couldn't, brithness, contrast, color warm and a few other options are marked as "not available" (he probably adjusted the brightness and changed something else too, that it's causing this thing). I updated the monitor driver, the vcard driver, plugged the monitor in other pc (I'm connected through dvi, but in the other pc i plugged through rgb) but nothing fixed it. Is there someway to force reset all the options or something like that to fix this? (I'm running Win7 RC1 but I don't think that it has something to do with it, it was working perfectly until he messed it up, and the other pc where I plugged it, runs winxp and the problem occurs too. And it doens't look like a the monitor is broken, it works like it always did, just these options are marked "not available" now...)

  Read the article

• Windows program to remove titlebar, frame, etc from a window?

  - by Nelson

  I like playing computer games in windowed mode, as opposed to full screen. I don't like staring at the title bar, frame, and other UI junk. I also don't like seeing other stuff on my desktop around the window. Is there a simple Windows program that will strip the UI chrome off of an arbitrary window from some other application? Extra points for an easy way to put a black screen underneath the window, hiding the desktop. Note: I'm looking specifically to handle windows that are smaller than my desktop size. There's a variety of 'windowed maximized' options that make a window exactly the desktop size, and positioned so all the UI decorations are off screen. (E.g.: ShiftWindow). I'm trying to strip all the decorations away from a window that's smaller than desktop size.

  Read the article

< Previous Page | 116 117 118 119 120 121 122 123 124 125 126 127  | Next Page >