Search Results

Search found 3325 results on 133 pages for 'route'.

Page 121/133 | < Previous Page | 117 118 119 120 121 122 123 124 125 126 127 128  | Next Page >

• Layer 3 switch routing

  - by Yoshiwaan

  I need help moving over to using our layer 3 switch as the inter vlan routing device rather than our cisco router. I've mostly got it working but I've got stuck near the end and need some advice (I think I just need a bit of education on the subject really). Cur I have a Dell PowerConnect 7048 connecting to a Cisco 1841 router. I've got a few key excerpts from the configs to provide the key information. On the powerconnect I have the following: ip routing ip default-gateway 172.31.14.1 ip route 0.0.0.0 0.0.0.0 172.31.14.1 253 ! interface vlan 1 ip address 172.31.14.254 255.255.255.0 exit interface vlan 2 ip address 172.31.19.254 255.255.255.0 exit interface vlan 4 ip address 172.31.16.254 255.255.255.0 ! interface Gi1/0/1 description 'Link to L7Router01' switchport mode trunk switchport trunk allowed vlan except 3,7-4093 exit ! and on the Cisco the following: interface FastEthernet0/0 ip address 172.31.14.1 255.255.255.0 ip nat inside ip virtual-reassembly ! interface FastEthernet0/0.2 description Accounts VLAN encapsulation dot1Q 2 ip address 172.31.19.1 255.255.255.0 ip nat inside ip virtual-reassembly ! interface FastEthernet0/0.4 description Voice VLAN encapsulation dot1Q 4 ip address 172.31.16.1 255.255.255.0 ip nat inside ip virtual-reassembly ! So what I'm doing is moving clients over so that their default gateway is a 172.31.x.254 address rather than a 172.31.x.1 address. This works great for inter-vlan routing, I have no issues with this. The switch can also access the router no worries, and users on the 172.31.14.0/24 network can access all interfaces and sub-interfaces on the router, including 172.31.14.1. They can also access all of the interfaces that the router connects off to, no worries there. The problem I have is that users on the 172.31.16.0/24 and 172.31.19.0/24 subnets cannot access either 172.31.14.1 or any of the subnets the router connects to. They can, however, connect to BOTH of the sub interfaces on the router from either subnet. What am I missing here? Why can't the vlans connect to the non-sub interface on the router? Are tagged packets being sent to this interface?

  Read the article

• Installing ImageMagick on Mac OSX 10.6

  - by Russell C.

  I just got a new Mac and am trying to setup a local Perl development environment. I'm using MAMP but also need the ImageMagick perl module installed in order to do some of the photo processing our scripts require. I tried installing ImageMagick manually but ran into some issues and after reading online a lot of people reported having issues going this route. The general consensus was to install it using MacPorts instead so I went ahead and installed MacPorts. Unfortunately, MacPorts can't seem to install it successfully either. Here is the command I'm using to try to install ImageMagick: sudo port install p5-perlmagick And here are all the errors reported during install: ---> Computing dependencies for p5-perlmagick ---> Building p5-perlmagick Error: Target org.macports.build returned: shell command " cd "/opt/local/var/macports/build/_opt_local_var_macports_sources_rsync.macports.org_release_ports_perl_p5-perlmagick/work/PerlMagick-6.32" && /usr/bin/make -j2 all " returned error 2 Command output: Magick.xs:10918: error: 'struct Methods' has no member named 'exception' Magick.xs:10918: error: request for member 'severity' in something not a structure or union Magick.xs:10918: error: 'ErrorException' undeclared (first use in this function) Magick.xs:10919: error: 'struct Methods' has no member named 'exception' Magick.xs:10920: warning: implicit declaration of function 'GetImageException' Magick.xs:10922: error: 'struct PackageInfo' has no member named 'image_info' Magick.xs:10922: error: 'struct Methods' has no member named 'adjoin' Magick.xs:10929: error: request for member 'severity' in something not a structure or union Magick.xs:10929: error: 'UndefinedException' undeclared (first use in this function) Magick.xs:10929: error: request for member 'severity' in something not a structure or union Magick.xs:10929: error: request for member 'reason' in something not a structure or union Magick.xs:10929: error: request for member 'severity' in something not a structure or union Magick.xs:10929: error: request for member 'reason' in something not a structure or union Magick.xs:10929: warning: pointer/integer type mismatch in conditional expression Magick.xs:10929: error: request for member 'description' in something not a structure or union Magick.xs:10929: error: request for member 'description' in something not a structure or union Magick.xs:10929: error: request for member 'severity' in something not a structure or union Magick.xs:10929: error: request for member 'description' in something not a structure or union Magick.xs:10929: warning: pointer/integer type mismatch in conditional expression Magick.xs:10929: error: request for member 'description' in something not a structure or union Magick.xs:10929: warning: passing argument 2 of 'Perl_sv_catpv' from incompatible pointer type Magick.xs:10929: warning: unused variable 'message' Magick.xs:10856: warning: unused variable 'filename' Magick.c:10784: warning: unused variable 'ref' Magick.c:10777: warning: unused variable 'ix' Magick.xs: In function 'boot_Image__Magick': Magick.xs:2122: warning: implicit declaration of function 'InitializeMagick' Magick.xs:2123: warning: implicit declaration of function 'SetWarningHandler' Magick.xs:2124: warning: implicit declaration of function 'SetErrorHandler' make: *** [Magick.o] Error 1 Error: Status 1 encountered during processing. Before reporting a bug, first run the command again with the -d flag to get complete output. I have no idea what the problem might be or how to go about successfully installing ImageMagick. I'd appreciate any help & advice that someone out there that has done this successfully might be able to provide. Thanks in advance!

  Read the article

• Cannot access a very specific site from my router

  - by DJDarkViper

  This is a problem for me because this site is important to me. It's MY website. And sadly my email is hosted on my site (which I cant access either) When I try to access my website when connected to my Linksys E3000 router, these days it simply just doesn't go through. When I ping it, its all Request Timed Out, and when I tracert C:\Users\Kyle>tracert blackjaguarstudios.com Tracing route to blackjaguarstudios.com [199.188.204.228] over a maximum of 30 hops: 1 <1 ms <1 ms <1 ms CISCO26565 [192.168.1.1] 2 16 ms 15 ms 11 ms 11.4.64.1 3 11 ms 9 ms 11 ms rd1cs-ge1-2-1.ok.shawcable.net [64.59.169.2] 4 20 ms 21 ms 22 ms 66.163.76.98 5 37 ms 36 ms 35 ms rc1nr-tge0-9-2-0.wp.shawcable.net [66.163.77.54] 6 112 ms 84 ms 85 ms rc2ch-pos9-0.il.shawcable.net [66.163.76.174] 7 86 ms 89 ms 90 ms rc4as-ge12-0-0.vx.shawcable.net [66.163.64.46] 8 90 ms 84 ms 85 ms eqix.xe-3-3-0.cr2.iad1.us.nlayer.net [206.223.115.61] 9 97 ms 97 ms 99 ms xe-3-3-0.cr1.atl1.us.nlayer.net [69.22.142.105] 10 128 ms 128 ms 126 ms ae1-40g.ar1.atl1.us.nlayer.net [69.31.135.130] 11 101 ms 97 ms 96 ms as16626.xe-2-0-5-102.ar1.atl1.us.nlayer.net [69.31.135.46] 12 100 ms 97 ms 197 ms 6509-sc1.abstractdns.com [207.210.114.166] 13 * * * Request timed out. 14 * * * Request timed out. 15 * * * Request timed out. 16 * * * Request timed out. 17 * * * Request timed out. 18 * * * Request timed out. 19 * * * Request timed out. 20 * * * Request timed out. 21 * * * Request timed out. 22 * * * Request timed out. 23 * * * Request timed out. 24 * * * Request timed out. 25 * * * Request timed out. 26 * * * Request timed out. 27 * * * Request timed out. 28 * * * Request timed out. 29 * * * Request timed out. 30 * * * Request timed out. Trace complete. C:\Users\Kyle> SHAW Cable being my ISP. Figuring this was all something to do with some setting I made on the router, I reset the thing back to factory defaults. Nope. So I'm at a bit of a loss what to do here, as NO device (Computers, Laptops, Tablets, Phones, PS3/ 360, etc) can access my site or its features, so it's not just my computer either. But every other site is just fine. When I connect to my neighbors router, the site comes up just fine. And shes with SHAW as well. What should I do?!

  Read the article

• Using OpenVPN, yet netflix.com blocks access

  - by user837848

  I have set up an OpenVPN server on a VPS in the USA and configured it to route all clients traffic through it. Everything seems to work fine regarding the VPN connection in gerneral. All ip lookup sites show me the us server's ip address and even hulu.com works(it won't work if you are not in the usa). But for some reason netflix.com says "Sorry, Netflix is not available in your country yet.". So I thought that netflix probably uses some more sophisticated ways to determine your location beyond just your ip address. But I could not find a way to get it to work until I dropped the idea of using a VPN and instead connected to the server via a simple socks tunnel with ssh by running: ssh -D 9999 user@serverip All I had to do was changing the key network.proxy.socks_remote_dns in Firefox from false to true to prevent DNS leaks and setting up the socks proxy. Then I could finally watch netflix.com. As a result I concluded that there is nothing in the browser(or something like system timezone) that tells netflix the location, so it has to have something to do with the OpenVPN config. After that I used tcpdump to log all the traffic on the server's network interface venet0 (OpenVZ VPS), visited netflix.com on the client while first connected to the VPN and then connected via socks tunnel and afterwards compared both outputs. The only thing that caught my eye was that while using the socks tunnel the server mainly used ipv6 to connect to netflix whereas it only used ipv4 when the client was connected to the OpenVPN server. But I don't get how that could make such a difference. So what am I missing? Is there a way to configure OpenVPN to also use ipv6 to connect to a website although there is only an ipv4 connection between the VPS and the client? Here is the server.conf of the OpenVPN server (OpenVZ VPS) local serverip port 443 proto tcp dev tun ca ./easy-rsa2/keys/ca.crt cert ./easy-rsa2/keys/vps1.crt key ./easy-rsa2/keys/vps1.key # This file should be kept secret dh ./easy-rsa2/keys/dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" client-to-client keepalive 10 120 tls-auth ta.key 0 # This file is secret cipher AES-256-CBC comp-lzo max-clients 4 user nobody group nogroup persist-key persist-tun status openvpn-status.log log-append openvpn.log verb 3 iptables forwarding iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o venet0 -j SNAT --to-source serverip (enabled ipv4 forwarding) I have tried everything always on a Win7 and a Debian client with only ipv4 connections and always made sure that they use the correct DNS server (tested with ipleak.net and tcpdump / wireshark). client.conf: client dev tun proto tcp remote serverip 443 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert client.crt key client.key ns-cert-type server tls-auth ta.key 1 cipher AES-256-CBC comb-lzo verb 3

  Read the article

• Troubleshooting an unstable internet connection

  - by Konrad Rudolph

  My MacBook Pro running OS X (10.9, but I had the same problem before) is connected to a Belkin router via WiFi and, using Virgin Media as the ISP, to the internet. The connection is extremely unstable – on some days, I get a ping timeout every few seconds. In addition, some domains seem to suffer general connectivity issues. For instance, I often find that while the youtube.com website loads, none of the videos (which are hosted on a separate domain) do. At other times, videos load but always fail to buffer, even though the actual connection speed is ok, even though I’ve disabled dash playback. Since I’m living in a rented room and the ISP contract isn’t actually mine I’ve got only limited possibilities of addressing the problem. In particular, I have no access to the router configuration and my non tech savvy landlady, while sympathetic, is not in a great hurry to hand the problem over to the ISP’s customer support. What’s more, I seem to be the only person in the house experiencing these problems – but I can imagine that this is simply because I’m the only one who’s using the internet continuously. I’m searching for specific tests that might be able to pinpoint – and ideally solve – the problem. So far all I’ve managed to do is establish that Virgin is routing my traffic in mysterious ways. Here’s an excerpt from traceroute google.co.uk. It’s worth mentioning that the host name doesn’t seem to matter a lot, the trace route is always the same. traceroute: Warning: google.co.uk has multiple addresses; using 62.254.36.148 traceroute to google.co.uk (62.254.36.148), 64 hops max, 52 byte packets 1 (192.168.2.1) 1.112 ms 1.300 ms 2.359 ms 2 10.100.32.1 (10.100.32.1) 11.926 ms 10.217 ms 24.987 ms 3 cmbg-core-1a-ae3-610.network.virginmedia.net (80.1.202.93) 28.809 ms * 66.653 ms 4 popl-bb-1b-ae16-0.network.virginmedia.net (212.43.163.141) 13.759 ms 126.504 ms 20.472 ms 5 nrth-bb-1b-et-010-0.network.virginmedia.net (62.253.175.57) 28.357 ms 16.398 ms 42.387 ms 6 nrth-bb-1c-ae1-0.network.virginmedia.net (62.253.174.110) 27.441 ms 15.622 ms 12.044 ms 7 lutn-icdn-1-ae0-0.network.virginmedia.net (62.253.175.82) 16.678 ms 28.463 ms 28.253 ms 8 * * * 9 * * * 10 * * * ^C If I let it, this goes on until the end of time. It never seems to reach a destination. Is this normal? A friend living in the same town who is also with Virgin Media has a more conventional traceroute output: 7 hops to google.co.uk, all of which send the ICMP TIME_EXCEEDED response. The obvious fix – rebooting the router – doesn’t seem to help. As far as I can tell, the WiFi connection is stable (I can always ping the router) so the problem is further downstream. I’ve tried using an alternative DNS before (OpenDNS) but if anything, this made things worse. In fact, it made all Google services nigh unreachable.

  Read the article

• VMWare ESXi virtual machine can contact the gateway but not the DNS server

  - by Nathan Palmer

  I am having a bit of a strange issue. I have a VMWare ESXi server with two virtual machines running on it. They are running just fine and can communicate on the network without a problem. I am now trying to add a third. I am installing Ubuntu 8.04 Server. I assign it a static IP address and it's a fresh installation. Once installed I can ping the gateway but I cannot ping the DNS server. It's on the same network with the other two VMs which are communicating just fine. I have tried to reinstall the operating system but it still fails to connect. Here is /etc/network/interfaces auto eth0 iface eth0 inet static address 192.168.1.23 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.1 dns-nameservers 208.67.222.222 #opendns dns-search mydomain.com Here is route Destination | Gateway | Genmask | Flags | Metric | Ref | Use | Iface localnet | * | 255.255.255.0 | U | 0 | 0 | 0 | eth0 default | 192.168.1.1 | 0.0.0.0 | UG | 100 | 0 | 0 | eth0 Since I'm running this behind a FortiGate this is what the sniff command gives me when I try to ping 208.67.222.222 arp who-has 192.168.1.1 tell 192.168.1.23 arp reply 192.168.1.1 is-at MAC 192.168.1.23 -> 208.67.222.222: icmp: echo request 192.168.1.23 -> 208.67.222.222: icmp: echo request 192.168.1.23 -> 208.67.222.222: icmp: echo request 192.168.1.23 -> 208.67.222.222: icmp: echo request 192.168.1.23 -> 208.67.222.222: icmp: echo request As you can see it looks like I never get a response. One interesting thing I notice is the arp reply's MAC doesn't look right. I have cleared the FortiGate's ARP cache though and checked the entry and it seems correct. The MAC it lists is the one for the router. However if I ping from a different virtual machine that is also Ubuntu 8.04 with a nearly identical configuration I get this. 192.168.1.22 -> 208.67.222.222: icmp: echo request 208.67.222.222 -> 192.168.1.22: icmp: echo reply 192.168.1.22 -> 208.67.222.222: icmp: echo request 208.67.222.222 -> 192.168.1.22: icmp: echo reply 192.168.1.22 -> 208.67.222.222: icmp: echo request 208.67.222.222 -> 192.168.1.22: icmp: echo reply So, what could I be missing? Thanks.

  Read the article

• KVM network bridge and public static IP for both host and guests

  - by Javier Martinez

  I have a Debian Server with 4 public static addresses. There is a KVM guest (also Debian) installed and running. What I want is to give the guest an IP of the host, so that both machines have public IPs. IP 1: 188.165.A.B IP 2: 178.33.CCC.D IP 3: 178.33.CCC.E IP 4: 178.33.CCC.F What should I do to have connection for host and guest ? This is network conf: # ifconfig br0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:188.165.A.B Bcast:188.165.255.255 Mask:255.255.255.0 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3618 errors:0 dropped:4 overruns:0 frame:0 TX packets:4853 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:599562 (585.5 KiB) TX bytes:1693443 (1.6 MiB) eth0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4274 errors:0 dropped:0 overruns:0 frame:0 TX packets:4879 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:720045 (703.1 KiB) TX bytes:1715641 (1.6 MiB) Interrupt:20 Memory:fe500000-fe520000 eth0:0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.D Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:1 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.E Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:2 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.F Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:27932 errors:0 dropped:0 overruns:0 frame:0 TX packets:27932 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1820862 (1.7 MiB) TX bytes:1820862 (1.7 MiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:87:40:ec inet6 addr: fe80::fc54:ff:fe87:40ec/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18 errors:0 dropped:0 overruns:0 frame:0 TX packets:204 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:1452 (1.4 KiB) TX bytes:16958 (16.5 KiB) #route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default aa.bb.cc.eu 0.0.0.0 UG 0 0 0 br0 188.165.255.0 * 255.255.255.0 U 0 0 0 br0 # brctl show bridge name bridge id STP enabled interfaces br0 8000.e840f20acc28 no eth0 vnet0 There is no firewall enabled and DNS is configured properly. What I want to achieve: | | | +----+-------------------------+-+------+ | | Host | | | | | | | | | | +------------+------+ | | eth0 | eth0:0-1 | | | 188.165.A.B | | | | | | | | | br0 vnet0 | | | +------------+------+ | | | | | | | | +------------+------+ | | | | | | | | eth0:2-+ | | | | 178.33.CCC.F | | | | | | | | Guest | | | +-------------------+ | +---------------------------------------+ Thanks you

  Read the article

• KVM network bridge and public static IP for both host and guests

  - by Javier Martinez

  I have a Debian Server with 4 public static addresses. There is a KVM guest (also Debian) installed and running. What I want is to give the guest an IP of the host, so that both machines have public IPs. IP 1: 188.165.A.B IP 2: 178.33.CCC.D IP 3: 178.33.CCC.E IP 4: 178.33.CCC.F What should I do to have connection for host and guest ? This is network conf: # ifconfig br0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:188.165.A.B Bcast:188.165.255.255 Mask:255.255.255.0 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3618 errors:0 dropped:4 overruns:0 frame:0 TX packets:4853 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:599562 (585.5 KiB) TX bytes:1693443 (1.6 MiB) eth0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4274 errors:0 dropped:0 overruns:0 frame:0 TX packets:4879 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:720045 (703.1 KiB) TX bytes:1715641 (1.6 MiB) Interrupt:20 Memory:fe500000-fe520000 eth0:0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.D Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:1 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.E Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:2 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.F Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:27932 errors:0 dropped:0 overruns:0 frame:0 TX packets:27932 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1820862 (1.7 MiB) TX bytes:1820862 (1.7 MiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:87:40:ec inet6 addr: fe80::fc54:ff:fe87:40ec/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18 errors:0 dropped:0 overruns:0 frame:0 TX packets:204 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:1452 (1.4 KiB) TX bytes:16958 (16.5 KiB) #route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default aa.bb.cc.eu 0.0.0.0 UG 0 0 0 br0 188.165.255.0 * 255.255.255.0 U 0 0 0 br0 # brctl show bridge name bridge id STP enabled interfaces br0 8000.e840f20acc28 no eth0 vnet0 There is no firewall enabled and DNS is configured properly. What I want to achieve: | | | +----+-------------------------+-+------+ | | Host | | | | | | | | | | +------------+------+ | | eth0 | eth0:0-1 | | | 188.165.A.B | | | | | | | | | br0 vnet0 | | | +------------+------+ | | | | | | | | +------------+------+ | | | | | | | | eth0:2-+ | | | | 178.33.CCC.F | | | | | | | | Guest | | | +-------------------+ | +---------------------------------------+ Thanks you

  Read the article

• Specifying network settings during SLES 11 auto installation

  - by banjer

  I'm setting up an autoinst.xml file for auto-installing SLES 11. I get prompted for the various interface settings per below, but they don't seem to stick once the server reboots. I don't think I have the xml defined correctly. I'm hoping someone has experience with this. <ask-list> <ask> <path>networking,dns,hostname</path> <question>Enter Hostname (server name)</question> <stage>initial</stage> <default>merkin</default> </ask> <ask> <path>networking,interfaces,interface,0,device</path> <question>Enter the primary ethernet device:</question> <stage>initial</stage> <default>eth0</default> </ask> <ask> <path>networking,interfaces,interface,0,ipaddr</path> <question>Enter the primary IP Address:</question> <stage>initial</stage> </ask> <ask> <path>networking,interfaces,interface,0,netmask</path> <question>Enter the Netmask Address:</question> <stage>initial</stage> </ask> <ask> <path>networking,routing,routes,route,0,gateway</path> <question>Enter the primary Gateway Address:</question> <stage>initial</stage> </ask> </ask-list> The first one for hostname seems to be sticking just fine, but the rest do not. As an alternative, is there a way to stop the autoinstall at the section where you configure the network devices so that the user can take over? I was able to show the partition proposal, but not sure how to do the same with the networking setup.

  Read the article

• how to notify a program of another program? dll? directory? path?

  - by Brady Trainor

  I am trying to experiment with GNUS email in Emacs, in Windows (EDIT: x64 bit). I've got it to work in Ubuntu, but struggling with it in Windows. From http://www.gnu.org/software/emacs/manual/html_mono/emacs-gnutls.html#Help-For-Users I read in second paragraph: This is a little bit trickier on the W32 (Windows) platform, but if you have the GnuTLS DLLs (available from http://sourceforge.net/projects/ezwinports/files/ thanks to Eli Zaretskii) in the same directory as Emacs, you should be OK. I have downloaded and unzipped the gnutls-3.0.9-w32-bin package, but am not sure what to do with it. I have tried putting it in Program Files (x86), which is "the same directory as Emacs". I have tried putting it in the emacs-24.3 folder. I consider merging all the folders in between the two, but am hesitant as that seems a difficult troubleshoot attempt compared to my knowledge on these matters. I think Emacs needs to somehow see the gnutls binaries and/or dlls. My knowledge is limited on this. I've also struggled to understand PATHs for sometime now, and am not sure if that approach is relevant here. FYI, the emacs directory contains folders labeled bin, etc, info, leim, lisp and site-lisp. The gnutls directory contains folder labeled bin, include, lib and share. Hmm, now I'm finding lots of links on adding paths. Still, I'm skeptical that I would only add gnutls.exe path, as it seems the dlls are needed. Some additional data for Ramhound's first comment I have been attempting the (require 'gnutls) route. This seems to be the most relevant parts in the log: Opening connection to imap.gmail.com via tls... gnutls.c: [1] (Emacs) GnuTLS library not found Opening TLS connection to `imap.gmail.com'... Opening TLS connection with `gnutls-cli --insecure -p 993 imap.gmail.com'...failed Opening TLS connection with `gnutls-cli --insecure -p 993 imap.gmail.com --protocols ssl3'...failed Opening TLS connection with `openssl s_client -connect imap.gmail.com:993 -no_ssl2 -ign_eof'...failed Opening TLS connection to `imap.gmail.com'...failed I am not sure what "in stallion" means. Emacs seems to have installed itself in program files (x86), so I assume it is 32 bit. I can try and figure out how to double check, but did not realize I would get such fast response time, and am headed out right now. I will try merging the files later tonight?

  Read the article

• Puppet - Possible to use software design patterns in modules?

  - by Mike Purcell

  As I work with puppet, I find myself wanting to automate more complex setups, for example vhosts for X number of websites. As my puppet manifests get more complex I find it difficult to apply the DRY (don't repeat yourself) principle. Below is a simplified snippet of what I am after, but doesn't work because puppet throws various errors depending up whether I use classes or defines. I'd like to get some feed back from some seasoned puppetmasters on how they might approach this solution. # site.pp import 'nodes' # nodes.pp node nodes_dev { $service_env = 'dev' } node nodes_prod { $service_env = 'prod' } import 'nodes/dev' import 'nodes/prod' # nodes/dev.pp node 'service1.ownij.lan' inherits nodes_dev { httpd::vhost::package::site { 'foo': } httpd::vhost::package::site { 'bar': } } # modules/vhost/package.pp class httpd::vhost::package { class manage($port) { # More complex stuff goes here like ensuring that conf paths and uris exist # As well as log files, which is I why I want to do the work once and use many notify { $service_env: } notify { $port: } } define site { case $name { 'foo': { class 'httpd::vhost::package::manage': port => 20000 } } 'bar': { class 'httpd::vhost::package::manage': port => 20001 } } } } } That code snippet gives me a Duplicate declaration: Class[Httpd::Vhost::Package::Manage] error, and if I switch the manage class to a define, and attempt to access a global or pass in a variable common to both foo and bar, I get a Duplicate declaration: Notify[dev] error. Any suggestions how I can implement the DRY principle and still get puppet to work? -- UPDATE -- I'm still having a problem trying to ensure that some of my vhosts, which may share a parent directory, are setup correctly. Something like this: node 'service1.ownij.lan' inherits nodes_dev { httpd::vhost::package::site { 'foo_sitea': } httpd::vhost::package::site { 'foo_siteb': } httpd::vhost::package::site { 'bar': } } What I need to happen is that sitea and siteb have the same parent "foo" folder. The problem I am having is when I call a define to ensure the "foo" folder exists. Below is the site define as I have it, hopefully it will make sense what I am trying to accomplish. class httpd::vhost::package { File { owner => root, group => root, mode => 0660 } define site() { $app_parts = split($name, '[_]') $app_primary = $app_parts[0] if ($app_parts[1] == '') { $tpl_path_partial_app = "${app_primary}" $app_sub = '' } else { $tpl_path_partial_app = "${app_primary}/${app_parts[1]}" $app_sub = $app_parts[1] } include httpd::vhost::log::base httpd::vhost::log::app { $name: app_primary => $app_primary, app_sub => $app_sub } } } class httpd::vhost::log { class base { $paths = [ '/tmp', '/tmp/var', '/tmp/var/log', '/tmp/var/log/httpd', "/tmp/var/log/httpd/${service_env}" ] file { $paths: ensure => directory } } define app($app_primary, $app_sub) { $paths = [ "/tmp/var/log/httpd/${service_env}/${app_primary}", "/tmp/var/log/httpd/${service_env}/${app_primary}/${app_sub}" ] file { $paths: ensure => directory } } } The include httpd::vhost::log::base works fine, because it is "included", which means it is only implemented once, even though site is called multiple times. The error I am getting is: Duplicate declaration: File[/tmp/var/log/httpd/dev/foo]. I looked into using exec, but not sure this is the correct route, surely others have had to deal with this before and any insight is appreciated as I have been grappling with this for a few weeks. Thanks.

  Read the article

• ubuntu eth0 not reconnecting after cable unplugged

  - by Alex

  I'm running kubuntu 9.10 w/ gnome, I have a static IP defined in /etc/network/interfaces When I unplugged my network cable and rebooted, then reconnected the network cable I was not able to connect. I tried using sudo ifup eth0, and then ifconfig and it seemed as though the IP address had been assigned and I was connected, but I wasn't. I then did ifdown eth0, and again ifup eth0. For some reason I'm not able to access the network. Furthermore, I also attempted to connect via wlan, and was able to connect to the wireless network, but cannot "see" the network. I can't transfer data or access the internet or anything on the network including the router. How do I resolve this? topsy@monolyth:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1c:25:1c:df:70 inet addr:192.168.1.145 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:25ff:fe1c:df70/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5720 errors:0 dropped:0 overruns:0 frame:0 TX packets:565 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:378035 (378.0 KB) TX bytes:46832 (46.8 KB) Memory:fe000000-fe020000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:240 (240.0 B) TX bytes:240 (240.0 B) By access the network I mean the local network as well as the internet. topsy@monolyth:~$ ping 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=9.14 ms 64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=1.24 ms 64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=1.01 ms 64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=1.00 ms [snip... all OK, icmp_seq from 5-30, time between 0.981-1.25ms] ^C --- 192.168.1.1 ping statistics --- 30 packets transmitted, 30 received, 0% packet loss, time 29035ms rtt min/avg/max/mdev = 0.971/1.300/9.140/1.458 ms topsy@monolyth:~$ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.0 * 255.255.255.0 U 0 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 eth0 default 192.168.1.1 0.0.0.0 UG 100 0 0 eth0 root@monolyth:~# cat /etc/resolv.conf # Generated by NetworkManager

  Read the article

• OpenVPN not sending traffic to internet?

  - by coleifer

  I've set up openvpn on my pi and am running into a small issue. I can connect to the VPN server and ping it just fine, and I can also connect to other machines on my local network. However I am unable, when connected to the VPN, to reach the outside world (either by name lookup or IP). here are the details: On the server the tun0 interface: tun0: flags=4305<UP,POINTOPOINT,RUNNING,NOARP,MULTICAST> mtu 1500 inet 10.8.0.1 netmask 255.255.255.255 destination 10.8.0.2 unspec 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 txqueuelen 100 (UNSPEC) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 I can ping it just fine: # ping -c 3 10.8.0.1 PING 10.8.0.1 (10.8.0.1) 56(84) bytes of data. 64 bytes from 10.8.0.1: icmp_seq=1 ttl=64 time=0.159 ms 64 bytes from 10.8.0.1: icmp_seq=2 ttl=64 time=0.155 ms 64 bytes from 10.8.0.1: icmp_seq=3 ttl=64 time=0.156 ms --- 10.8.0.1 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2002ms Routing table # ip route show default via 192.168.1.1 dev eth0 metric 204 10.8.0.0/24 via 10.8.0.2 dev tun0 10.8.0.2 dev tun0 proto kernel scope link src 10.8.0.1 192.168.1.0/24 dev eth0 proto kernel scope link src 192.168.1.6 metric 204 I also have ip traffic forwarding: net.ipv4.ip_forward = 1 I do not have any custom iptables rules (that I'm aware of). On the client, I can connect to the VPN. Here is my tun0: tun0: flags=4305<UP,POINTOPOINT,RUNNING,NOARP,MULTICAST> mtu 1500 inet 10.8.0.6 netmask 255.255.255.255 destination 10.8.0.5 unspec 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 txqueuelen 100 (UNSPEC) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 21 bytes 1527 (1.4 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 And on the client I can ping it: sudo ping -c 3 10.8.0.6 PING 10.8.0.6 (10.8.0.6) 56(84) bytes of data. 64 bytes from 10.8.0.6: icmp_seq=1 ttl=64 time=0.035 ms 64 bytes from 10.8.0.6: icmp_seq=2 ttl=64 time=0.026 ms 64 bytes from 10.8.0.6: icmp_seq=3 ttl=64 time=0.032 ms --- 10.8.0.6 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 1998ms rtt min/avg/max/mdev = 0.026/0.031/0.035/0.003 ms I can ssh from the client into another server on my LAN (192.168.1.x), however I cannot reach anything outside my LAN. Here's some of the server logs at the bottom of this gist: https://gist.github.com/coleifer/6ef95c3008f130249933/edit I am frankly out of ideas! I don't think it's my client because both my laptop and my phone (which has an openvpn client) exhibit the same behavior. I had OpenVPN installed on this pi before using debian and it worked, so I don't think it's my router but of course anything is possible.

  Read the article

• How to add IP range to a server?

  - by Efe Cakinberk

  Hello, First of all I must say that I'm ver inexperienced server and network user. But I rented a unmanaged dedicated server. Well I didn't know what unmanaged really means, then I learned it when I needed support. Well I must do everything by myself. I have a problem. I had already 4 IPs on my server when I rented it. But then I needed more Ips and my server assigned me 32 Ips in which I can only use 27 of them. 85.25.230.0 - 85.25.230.31 this is my Ip range and they say the following Ips must not be configured on the server: 85.25.230.0 - network address 85.25.230.1 - gateway address 85.25.230.2 - router redundancy 85.25.230.3 - router redundancy 85.25.230.31 - broadcast address But the problem is ok Ips are assigned to me but they are not setup on my server. How will I setup Ips to work on my server? I did this after my reseach on google: I used this command on command prompt: route add 85.25.230.0 mask 255.255.255.224 85.25.230.1 metric 1 if then it said OK!. and I thought they should be working. (btw, mask is given to me by my ISP and I don't know metric 1 and if means I just saw it on the net and write it here) I setup my domains via using Plesk Kontrol Panel. So i added one domain and setup one of my new Ips 85.25.230.5 to it. But no it is not working. When I visit the domain via browser, there is a Plesk page comes and says this domain is not configured on the server. Then I changed the domains Ip to one of my old Ips which are given to me with the server and which I have been using for my other domains for a long time. Ok in a second, domain started working. I set it back to my new Ip and domain did not work. As I said, I'm not an expert and do not now the logic. But I'm eager to learn. Can you tell me what might couse the problem and did I do wrong while setting up IP RANGE to my server, if so how can I set them up? Thank you, Efe

  Read the article

• nginx, php-cgi and "No input file specified."

  - by Stephen Belanger

  I'm trying to get nginx to play nice with php-cgi, but it's not quite working how I'd like. I'm using some set variables to allow for dynamic host names--basically anything.local. I know that stuff is working because I can access static files properly, however php files don't work. I get the standard "No input file specified." error which normally occurs when the file doesn't exist, but it definitely does exist and the path is correct because I can access the static files in the same path. It could possibly be a permissions thing, but I'm not sure how that could be an issue. I'm running this on Windows under my own user account, so I think it should have permission unless php-cgi is running under a different user without me telling it to. . Here's my config; worker_processes 1; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; sendfile on; keepalive_timeout 65; gzip on; server { # Listen for HTTP listen 80; # Match to local host names. server_name *.local; # We need to store a "cleaned" host. set $no_www $host; set $no_local $host; # Strip out www. if ($host ~* www\.(.*)) { set $no_www $1; rewrite ^(.*)$ $scheme://$no_www$1 permanent; } # Strip local for directory names. if ($no_www ~* (.*)\.local) { set $no_local $1; } # Define default path handler. location / { root ../Users/Stephen/Documents/Work/$no_local.com/hosts/main/docs; index index.php index.html index.htm; # Route non-existent paths through Kohana system router. try_files $uri $uri/ /index.php?kohana_uri=$request_uri; } # pass PHP scripts to FastCGI server listening on 127.0.0.1:9000 location ~ \.php$ { root ../Users/Stephen/Documents/Work/$no_local.com/hosts/main/docs; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; include fastcgi.conf; } # Prevent access to system files. location ~ /\. { return 404; } location ~* ^/(modules|application|system) { return 404; } } }

  Read the article

• TCP/IP & throughput between FreeNAS (BSD) server & other LAN machines

  - by Tim Dickerson

  I have got a question for someone that knows BSD a bit better than me that are in regards to my LAN setup at home/work here outside Chicago. I can't seem to fully optimize my network's (LAN) thoughput via my FreeNAS (BSD based) file server. It runs with the latest FreeBSD release which is modified to support several protocols for file transfers and more. Every machine that is behind my Smoothwall (Linux based) router is on the usual 192.168.0.x subnet and for most part works just fine. Behind the Smoothwall box, all machines are connected to a GB HP unmanaged switch. I host a large WISP here and have an OC-3 connection here at home/work and have no issues with downloading/uploading from/to the 'net'. My problem is with throughput. When I try and transfer large files...really any for that matter..between any of the machines to/and from the FreeNAS server via FTP, the max throughput I can achieve say between a Win 7 or a Linux box is ~65Mbit/sec. All machines are running Intel Pro 1000 GB NIC's and all cable is CAT6. Each is set to 'auto negotiation' and each shows 1500 MTU Full Duplex @1GB so I know the hardware is okay. I have not adjusted the MTU on any machine as I understand it to be pointless unless certain configurations are used (I assume I am not one of those). My settings for the FreeNAS machine are the following: # FreeNAS /etc/sysctl.conf - pertinent settings shown kern.ipc.maxsockbuf=262144 kern.ipc.nmbclusters=32768 kern.ipc.somaxconn=8192 kern.maxfiles=65536 kern.maxfilesperproc=32768 net.inet.tcp.delayed_ack=0 net.inet.tcp.inflight.enable=0 net.inet.tcp.path_mtu_discovery=0 net.inet.tcp.recvbuf_auto=1 net.inet.tcp.recvbuf_inc=524288 net.inet.tcp.recvbuf_max=16777216 net.inet.tcp.recvspace=65536 net.inet.tcp.rfc1323=1 net.inet.tcp.sendbuf_inc=16384 net.inet.tcp.sendbuf_max=16777216 net.inet.tcp.sendspace=65536 net.inet.udp.recvspace=65536 net.local.stream.recvspace=65536 net.local.stream.sendspace=65536 net.inet.tcp.hostcache.expire=1 From what I can tell, that looks to be a somewhat optimized profile for a typical BSD machine acting as a server for a LAN. I might be wrong and just wanted to find out from someone that knows BSD better than I do if indeed that is ok or if something is out of tune or what. Are there other ways I would find better for P2P file transfers? I honestly do not know what I SHOULD be looking for with respect to throughput between the NAS box and another client when xferring files via FTP, but I am told that what I get on average (40-70MB/sec) is too low for what it could be. I have thought about adding another NIC in the FreeNAS box as well as the Win7 machine and use a X-over cable via a static route, but wanted to check with someone first to see if that might be worth it or not. I don't know if doing that would bypass the HP GB switch and allow for a machine to machine xfer anyways. The FTP client I use is: Filezilla and have tried both active and passive modes with no real gain over each other. The NAS box runs ProFTPD.

  Read the article

• Understanding packet flows over RVI

  - by choco-loo

  I'm trying to get a full grasp of firewall filters and how to apply them on a Juniper EX4200 switch - to be able to block ports, police traffic and shape traffic. The network architecture is as follows internet >-< vlan4000 >-< vlan43 vlan4000 is a public "routed" block (where all the IPs are routed to and the internet gw is) vlan43 is a vlan with public IPs with devices (servers) attached There are static routes and RVI's on the EX4200 to send all traffic via vlan4000's gateway to reach the internet. I've set up filters on both input and output of the respective RVI's and VLAN's - with simple counters, to measure traffic flow from a server inside of vlan43 and a server on the internet. Using a combination of iperf for UDP and TCP tests and fping for ICMP tests - I observed the following, icmp vlan43>internet internet>vlan43 unit4000-counter-in 0 0 unit4000-counter-out 0 0 unit43-counter-in 100 100 unit43-counter-out 0 0 vlan4000-counter-in 6 4 vlan4000-counter-out 107 104 vlan43-counter-in 101 100 vlan43-counter-out 100 100 tcp vlan43>internet internet>vlan43 unit4000-counter-in 0 0 unit4000-counter-out 0 0 unit43-counter-in 73535 38480 unit43-counter-out 0 0 vlan4000-counter-in 7 8 vlan4000-counter-out 73543 38489 vlan43-counter-in 73535 38481 vlan43-counter-out 38938 75880 udp vlan43>internet internet>vlan43 unit4000-counter-in 0 0 unit4000-counter-out 0 0 unit43-counter-in 81410 1 unit43-counter-out 0 0 vlan4000-counter-in 18 7 vlan4000-counter-out 81429 8 vlan43-counter-in 81411 1 vlan43-counter-out 1 85472 My key goals are to set up a few filters and policers, as there will be many more VLANs - that all need protecting from each other and the internet. Then globally limit/police all outbound traffic to the internet Block inbound ports to vlan43 (eg. 22) Limit outbound traffic from vlan43 (to the internet) Limit outbound traffic from vlan43 (to other vlans) Limit outbound traffic from vlan4000 (to the internet from all vlans) Route traffic from vlans via specific routing instances (FBF) The question What I want to understand is why there isn't ever any activity on unit4000 or vlan4000 inbound or outbound counter - is this because there isn't a device on this VLAN - and that the traffic is only traversing it? And with regards to the TCP test - why is there twice as many packets on unit43-counter-in, vlan4000-counter-out and vlan43-counter-in - is this counting both the inbound and outbound traffic?

  Read the article

• Latency issues over internet

  - by Stevo

  I have a Media Temple server running http://www.popsapp.com which I am having latency issues with. If I run ab -n 100 -c 10 http://www.popsapp.com/ from my local machine I get very bad stats e.g.: Connection Times (ms) min mean[+/-sd] median max Connect: 179 3375 2185.4 2837 12525 Processing: 0 505 693.3 229 4564 Waiting: 0 50 115.4 0 415 Total: 964 3880 2094.5 3159 12608 Whereas if I run it from a rackspace server I have I get this: Connection Times (ms) min mean[+/-sd] median max Connect: 75 76 3.3 75 84 Processing: 235 339 81.4 315 579 Waiting: 159 249 61.7 234 411 Total: 311 415 82.0 390 663 To me this looks like intermediate network issues, but I wouldn't have thought it could be this bad! Any ideas how I can improve it? Here's the trace route traceroute to www.popsapp.com (216.70.105.183), 64 hops max, 52 byte packets 1 192.168.2.1 (192.168.2.1) 3.738 ms 0.953 ms 1.418 ms 2 host-92-22-112-1.as13285.net (92.22.112.1) 27.409 ms 97.093 ms 78.858 ms 3 host-78-151-225-141.static.as13285.net (78.151.225.141) 61.830 ms 170.484 ms 113.288 ms 4 host-78-151-225-80.static.as13285.net (78.151.225.80) 101.513 ms host-78-151-225-22.static.as13285.net (78.151.225.22) 64.718 ms 47.309 ms 5 xe-11-1-0-rt001.sov.as13285.net (62.24.240.14) 98.381 ms 114.424 ms xe-11-1-0-rt001.the.as13285.net (62.24.240.6) 96.592 ms 6 host-78-144-1-59.as13285.net (78.144.1.59) 36.799 ms host-78-144-1-63.as13285.net (78.144.1.63) 178.426 ms host-78-144-1-61.as13285.net (78.144.1.61) 85.516 ms 7 xe-10-0-0-scr010.thn.as13285.net (78.144.0.224) 88.158 ms host-78-144-0-207.as13285.net (78.144.0.207) 35.132 ms host-78-144-0-153.as13285.net (78.144.0.153) 121.464 ms 8 limelight-pp-thn.as13285.net (78.144.3.6) 46.987 ms limelight-pp-sov.as13285.net (78.144.5.18) 108.025 ms 40.169 ms 9 tge11-1.fr4.lga.llnw.net (69.28.172.149) 109.603 ms ve6.fr4.lon.llnw.net (68.142.88.221) 121.681 ms 38.609 ms 10 tge11-1.fr4.lga.llnw.net (69.28.172.149) 111.981 ms 113.744 ms 111.711 ms 11 tge8-2.fr4.iad.llnw.net (69.28.189.34) 117.102 ms ve5.fr4.iad.llnw.net (69.28.171.214) 184.372 ms 146.178 ms 12 cr02-1-1.iad1.net2ez.com (65.97.48.254) 182.880 ms net2ez.tge2-2.fr4.iad.llnw.net (69.28.156.170) 150.489 ms 121.862 ms 13 65.97.50.26 (65.97.50.26) 184.620 ms cr02-1-1.iad1.net2ez.com (65.97.48.254) 156.136 ms 131.963 ms 14 65.97.50.26 (65.97.50.26) 124.899 ms 126.537 ms 123.322 ms 15 e1.4.as02.iad01.mtsvc.net (70.32.64.246) 134.647 ms 186.307 ms 211.059 ms 16 popsapp.com (216.70.105.183) 118.876 ms 113.189 ms vzx258.mediatemple.net (216.70.104.17) 131.012 ms Looks to me like there is significant delay across the limelight network. This would explain why the traceroute via my rackspace server doesn't suffer from the same delay as they will be using their own trunk.

  Read the article

• Windows 2008 running as KVM guest networking issue

  - by Evolver

  I have a strange networking problem with Windows 2008 server R2, running as guest under KVM-Qemu host. Host is CentOS 6.3 x86_64. It's network settings: # cat /etc/sysconfig/network-scripts/ifcfg-br0 DEVICE=br0 BOOTPROTO=static BROADCAST=xx.xx.xx.63 IPADDR=xx.xx.xx.4 NETMASK=255.255.255.192 NETWORK=xx.xx.xx.0 ONBOOT=yes TYPE=Bridge # cat /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 HWADDR=xx:xx:xx:xx:xx:xx ONBOOT=yes BRIDGE=br0 IPV6INIT=yes IPV6_AUTOCONF=yes # cat /etc/sysconfig/network NETWORKING=yes NETWORKING_IPV6=no HOSTNAME=my.hostname GATEWAY=xx.xx.xx.1 # cat /etc/sysctl net.ipv4.ip_forward = 1 # tried to set it to 0 without any changes net.ipv4.conf.default.rp_filter = 1 # tried to set it to 0 without any changes net.ipv4.conf.default.accept_source_route = 0 # tried to set it to 1 without any changes kernel.sysrq = 0 kernel.core_uses_pid = 1 net.ipv4.tcp_syncookies = 1 net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-call-arptables = 0 kernel.msgmnb = 65536 kernel.msgmax = 65536 kernel.shmmax = 68719476736 kernel.shmall = 4294967296 # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface xx.xx.xx.0 0.0.0.0 255.255.255.192 U 0 0 0 br0 169.254.0.0 0.0.0.0 255.255.0.0 U 1004 0 0 br0 0.0.0.0 xx.xx.xx.1 0.0.0.0 UG 0 0 0 br0 Node IP is xx.xx.xx.4, guest IP is xx.xx.xx.24, both host and guest is in the same network (/26). There are several linux guest running fine on the node (centos, debian, ubuntu, arch), and even Windows 2003 x86 also running fine. But Win2008 does not. I wonder, what's the difference. From Win2008 guest I can ping nothing: neither gateway, nor any other IP, even they are in the same subnet. From outside I also cannot ping guest. Almost. If I ping it from another server in same subnet, it's barely pinging, losing more than 90% packets. Firewall on the guest is completely off. Tried to set up network manually as well as via DHCP without success (BTW, DHCP set up network settings correctly). I suspect that is a kind of routing problem, but I spent whole day and still cannot figure it out. I would be appreciate for any help.

  Read the article

• Snow Leopard can see Windows shares in Finder but can't connect

  - by Randy Miller

  I have an iMac with the latest version of Snow Leopard on it. I have a NAS drive and a Windows machine that both show up in the Finder's 'Shared' section. However, if I click on them, Finder says "Connection Failed". Clicking on 'Connect As...' gives an error dialog that says "The server 'blah' may not exist or it is unavailable at this time." Points of interest: All machines are receiving their IP/DNS info from the router using DHCP. I have a Mac Mini on the same network that connects to the NAS drive and windows machine perfectly with no config (i.e. worked out of the box). Both Macs are on the same version of Snow Leopard. There is no password required to access the NAS share. I've never setup a WINS server on any machines and all machines are using 'workgroup' by default. I've tried putting "workgroup" in the Mac's workgroup entry and have tried leaving it blank, neither solves the problem. Here are some things I have tried: Finder-Connect To Server: smb:///share. This works, but by name does not. Terminal-mount_smbfs //@/share share. This also works by ip, but not be name, resulting in "mount_smbfs: server connection failed: No route to host". If I put the IP address of the NAS in the WINS server entry in the Mac's network setup, I can connect by name. It obviously seems to be a name resolution error, but I can't figure out why. The only thing that has changed since it used to work is that I got a new router that now gives out DHCP (all machines are dhcp clients) addresses of 192.168.x.x, but used to be 10.0.x.x. I've grep'd through everything that might have saved that old address, but can't find anything. It's also worth noting that the second Mac (the one that connects successfully) was added to the network after the router change. Please let me know if there are additional points of information needed to troubleshoot this further. Thanks, Randy

  Read the article

• Why can I view my site over a 3G connection but not through my wifi?

  - by Jonathan

  So, I am sitting in my office with four computers on the same network and internet connection. Two of the computers can visit this particular website. Two of the computer get a message "Google Chrome could not find". I have tried FF and IE also with the same problem. I can view the site 90% of the time on two of the working computers although the site seems slow and sometimes I also get the same errors as the other two computers. I have flushed the DNS, reset the router, tested the site on other peoples computers with success. Is this likely to be a site issue, an ISP issue, a hosting issue? Any advice is greatly appreciated. Here is the ping from the working machine: C:\Users\Jon>ping www.balihaicruises.com Pinging www.balihaicruises.com [208.113.173.102] with 32 bytes of data: Reply from 208.113.173.102: bytes=32 time=331ms TTL=47 Reply from 208.113.173.102: bytes=32 time=327ms TTL=47 Reply from 208.113.173.102: bytes=32 time=326ms TTL=47 Reply from 208.113.173.102: bytes=32 time=329ms TTL=47 Ping statistics for 208.113.173.102: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 326ms, Maximum = 331ms, Average = 328ms Traceroute: Tracing route to www.balihaicruises.com [208.113.173.102] over a maximum of 30 hops: 1 1 ms 17 ms 3 ms 192.168.1.1 2 42 ms 37 ms 36 ms 180.254.224.1 3 39 ms 47 ms 40 ms 180.252.1.69 4 36 ms 616 ms 57 ms 61.94.115.221 5 84 ms 76 ms 80 ms 180.240.191.98 6 73 ms 80 ms 72 ms 180.240.191.97 7 157 ms 143 ms 116 ms 180.240.190.82 8 115 ms 113 ms 120 ms ae1-123.hkg11.ip4.tinet.net [183.182.80.93] 9 331 ms 332 ms 335 ms xe-3-2-1.was14.ip4.tinet.net [89.149.184.30] 10 327 ms 330 ms 331 ms internap-gw.ip4.tinet.net [77.67.69.254] 11 437 ms 415 ms 350 ms border10.pc2-bbnet2.wdc002.pnap.net [216.52.127.73] 12 322 ms 823 ms 398 ms dreamhost-2.border10.wdc002.pnap.net [216.52.125.74] 13 328 ms 336 ms 326 ms ip-208-113-156-4.dreamhost.com [208.113.156.4] 14 326 ms 328 ms 336 ms ip-208-113-156-14.dreamhost.com [208.113.156.14] 15 327 ms 331 ms 333 ms apache2-udder.crisp.dreamhost.com [208.113.173.102] And then for the machine that doesn't work: C:\Users\Microsoft>ping www.balihaicruises.com Ping request could not find host www.balihaicruises.com. Please check the name and try again. C:\Users\Microsoft>tracert www.balihaicruises.com Unable to resolve target system name www.balihaicruises.com.

  Read the article

• Exchange 2007 and migrating only some users under a shared domain name

  - by DomoDomo

  I'm in the process of moving two law firms to hosted Exchange 2007, a service that the consulting company I work for offers. Let's call these two firms Crane Law and Poole Law. These two firms were ONE firm just six months ago, but split. So they have three email domains: Old Firm: craneandpoole.com New Firm 1: cranelaw.com New Firm 2: poolelaw.com Both Firm 1 & Firm 2 use craneandpoole.com email addresses, as for the other two domains, only people who work at the respective firm use that firm's domain name, natch. Currently these two firms are still using the same pre-split internal Exchange 2007 server, where MX records for all three domains point. Here's the problem. I'm not moving both companies at the same time. I'm moving Crane Law two weeks before Poole Law. During this two weeks, both companies need to be able to: Continue to receive emails addressed to craneandpoole.com Send emails between firms, using cranelaw.com and poolelaw.com accounts I also have a third problem: I'd like to setup all three domains in my hosting infrastructure way ahead of time, to make my own life easier What would solve all my problems would be, if there is some way I can tell Exchange 2007, even though this domain exists locally forward on the message to the outside world using public MX record as a basis for where to send it (or if I could somehow create a route for it statically that would work too). If this doesn't work, to address points #1 when I migrate Crane Law, I will delete all references locally to cranelaw.com on their current Exchange server, and setup individual forwards for each of their craneandpool.com mailboxes to forward to our hosted exchange server. This will also take care of point #2, since the cranelaw.com won't be there locally, when poolelaw.com tries to send to cranelaw.com, public MX records will be used for mail routing decisions and go to my hosted exchange. The bummer of that though is, I won't be able to setup poolelaw.com ahead of time in hosted Exchange, will have to wait to do it day of :( Sorry for the long and confusing post. Just wondering if there is a better or simpler way to do what I want? Three tier forests and that kind of thing are out, this is just a two week window where they won't be in the same place.

  Read the article

• How to configure a tun interface on Linux for SSH port forwarding?

  - by sarshad

  I am trying to forward port 139 from a Windows machine to my Ubuntu SSH server on a tun interface with the ip address 10.0.0.1. This is so that I can access the windows shares on the machine on my Ubuntu server, through the reverse tunnel. I can forward ports to 127.0.0.1, but not to 10.0.0.1. On windows I am using the Tunnelier ssh client. On my Ubuntu server, the following message is printed in auth.log: Received disconnect from 124.109.51.154: 11: Server denied request for client-side server-2-client forwarding on 10.0.0.1:139. So far i have tried the following settings: GatewayPorts yes PermitTunnel yes AllowTcpForwarding yes in the /etc/ssh/sshd_config file, but it did not work. I set up the tun like this: sudo tunctl -t loc_0 -u myusername sudo ifconfig loc_0 inet 10.0.0.1 netmask 255.255.255.0 up The settings in the Tunneler ssh client should not matter because I can forward port 139 successfully to the Microsoft Loopback Adapter on a Windows machine running the WinSSHD server. Versions: Windows is XP SP3, Ubuntu is 10.10. Update: I tried to forward the port to a number greater than 1024 mentioning the IP address of the tun, and it successfully connected but the forwarding was done on 127.0.0.1 instead of the tun's IP address 10.0.0.1. So there are two separate problems now, when connecting from the Windows machine: 1) Forwarding on ports less than 1024 is probably being denied. How can we allow that on the server? 2) Forwarding is done only on 127.0.0.1 even if I mention 10.0.0.1 which is the tun's IP address. Another attempt: I also tried to forward port 22 of a Linux machine to the tun's port 55567. It showed success. But when I tried to ssh into that port using both local addresses, on the Linux machine in its debug display I got the error Connection failed: no route to host when using 127.0.0.1 to connect and simply Connection refused when using the tun's IP address. So the tun is not getting the forwarded port no matter we connect from a Windows client or a Linux client.

  Read the article

• Ubuntu: Multiple NICs, one used only for Wake-On-LAN

  - by jcwx86

  This is similar to some other questions, but I have a specific need which is not covered in the other questions. I have an Ubuntu server (11.10) with two NICs. One is built into the motherboard and the other is a PCI express card. I want to have my server connected to the internet via my NAT router and also have it able to wake from suspend using a Magic Packet (henceforth referred to as Wake-On-LAN, WOL). I can't do this with just one of the NICs because each has an issue - the built-in NIC will crash the system if it is placed under heavy load (typically downloading data), whilst the PCI express NIC will crash the system if it is used for WOL. I have spent some time investigating these individual problems, to no avail. My plan is thus: use the built-in NIC solely for WOL, and use the PCI express card for all other network communication except WOL. Since I send the WOL Magic Packet to a specific MAC address, there is no danger of hitting the wrong NIC, but there is a danger of using the built-in NIC for general network access, overloading it and crashing the system. Both NICs are wired to the same LAN with address space 192.168.0.0/24. The built-in ethernet card is set to have interface name eth1 and the PCI express card is eth0 in Ubuntu's udev persistent rules (so they stay the same upon reboot). I have been trying to set this up with the /etc/network/interfaces file. Here is where I am currently: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.0.3 netmask 255.255.255.0 network 192.168.0.0 broadcast 192.168.0.255 gateway 192.168.0.1 auto eth1 iface eth1 inet static address 192.168.0.254 netmask 255.255.255.0 I think by not specifying a gateway for eth1, I prevent it being used for outgoing requests. I don't mind if it can be reached on 192.168.0.254 on the LAN, i.e. via SSH -- it's IP is irrelevant to WOL, which is based on MAC addresses -- I just don't want it to be used to access internet resources. My kernel routing table (from route -n) is Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 My question is this: Is this sufficient for what I want to achieve? My research has thrown up the idea of using static routing to specify that eth1 should only be used for WOL on the local network, but I'm not sure this is necessary. I have been monitoring the activity of the interfaces using iptraf and it seems like eth0 takes the vast majority of the packets, though I am not sure that this will be consistent based on my configuration. Given that if I mess up the configuration, my system will likely crash, it is important to me to have this set up correctly!

  Read the article

• Routing a PPTP client and VMware Server instance running on the same box

  - by servermanfail

  I have a Windows 2003 SBS box. It has 2 physical NIC's: WAN and LAN. The WAN is a public IP. The LAN is a simple 192.168.2.x subnet with Microsoft DHCP Server. Microsoft Routing and Remote Access Service is used to provide NAT to LAN. The box also runs VMware Server with a virtual machine running Windows XP. I want people to be able to VPN into the box, and connect to these virtual machines on the MSRDP port. I can VPN (PPTP) into the 2003 SBS box fine, as well as ping other machines on the LAN. I can ping the VM from a physical workstation on the LAN and vice-versa. I can ping the VPN client from the a physical workstation on the LAN and vice-versa. I can ping the VPN client from the Server console and vice-versa. I can ping the VM client from the Server console and vice-versa. But I cannot ping the VPN client from the VM and vice-versa. I was hoping to set up 2 or 3 Windows XP virtual machines on our only server, so that a couple of people can remote in to work without having to leave a physical machine on in the office. You could this attempted set up a "poor mans terminal server". On the 2003 SBS Server:- C:\Documents and Settings\Administrator>route print IPv4 Route Table =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x2 ...00 50 56 c0 00 08 ...... VMware Virtual Ethernet Adapter for VMnet8 0x3 ...00 50 56 c0 00 01 ...... VMware Virtual Ethernet Adapter for VMnet1 0x10004 ...00 53 45 00 00 00 ...... WAN (PPP/SLIP) Interface 0x10005 ...00 11 43 d4 69 13 ...... Broadcom NetXtreme Gigabit Ethernet 0x10006 ...00 11 43 d4 69 14 ...... Broadcom NetXtreme Gigabit Ethernet #2 =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 81.123.144.22 81.123.144.21 1 81.123.144.20 255.255.255.252 81.123.144.21 81.123.144.21 1 81.123.144.21 255.255.255.255 127.0.0.1 127.0.0.1 1 81.255.255.255 255.255.255.255 81.123.144.21 81.123.144.21 1 86.135.78.235 255.255.255.255 81.123.144.22 81.123.144.21 1 109.152.62.236 255.255.255.255 81.123.144.22 81.123.144.21 1 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.2.0 255.255.255.0 192.168.2.3 192.168.2.3 1 192.168.2.3 255.255.255.255 127.0.0.1 127.0.0.1 1 192.168.2.26 255.255.255.255 192.168.2.32 192.168.2.32 1 192.168.2.28 255.255.255.255 192.168.2.32 192.168.2.32 1 192.168.2.32 255.255.255.255 127.0.0.1 127.0.0.1 50 192.168.2.50 255.255.255.255 127.0.0.1 127.0.0.1 1 192.168.2.255 255.255.255.255 192.168.2.3 192.168.2.3 1 192.168.10.0 255.255.255.0 192.168.10.1 192.168.10.1 20 192.168.10.1 255.255.255.255 127.0.0.1 127.0.0.1 20 192.168.10.255 255.255.255.255 192.168.10.1 192.168.10.1 20 192.168.96.0 255.255.255.0 192.168.96.1 192.168.96.1 20 192.168.96.1 255.255.255.255 127.0.0.1 127.0.0.1 20 192.168.96.255 255.255.255.255 192.168.96.1 192.168.96.1 20 224.0.0.0 240.0.0.0 81.123.144.21 81.123.144.21 1 224.0.0.0 240.0.0.0 192.168.2.3 192.168.2.3 1 224.0.0.0 240.0.0.0 192.168.10.1 192.168.10.1 20 224.0.0.0 240.0.0.0 192.168.96.1 192.168.96.1 20 255.255.255.255 255.255.255.255 81.123.144.21 81.123.144.21 1 255.255.255.255 255.255.255.255 192.168.2.3 192.168.2.3 1 255.255.255.255 255.255.255.255 192.168.10.1 192.168.10.1 1 255.255.255.255 255.255.255.255 192.168.96.1 192.168.96.1 1 Default Gateway: 81.123.144.22 =========================================================================== Persistent Routes: None C:\Documents and Settings\Administrator>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : 2003server Primary Dns Suffix . . . . . . . : mycompany.local Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : Yes WINS Proxy Enabled. . . . . . . . : Yes DNS Suffix Search List. . . . . . : mycompany.local gateway.2wire.net Ethernet adapter VMware Network Adapter VMnet8: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet 8 Physical Address. . . . . . . . . : 00-50-56-C0-00-08 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.10.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter VMware Network Adapter VMnet1: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet 1 Physical Address. . . . . . . . . : 00-50-56-C0-00-01 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.96.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : PPP adapter RAS Server (Dial In) Interface: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : WAN (PPP/SLIP) Interface Physical Address. . . . . . . . . : 00-53-45-00-00-00 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.2.32 Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : NetBIOS over Tcpip. . . . . . . . : Disabled Ethernet adapter LAN: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet Physical Address. . . . . . . . . : 00-11-43-D4-69-13 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.2.50 Subnet Mask . . . . . . . . . . . : 255.255.255.0 IP Address. . . . . . . . . . . . : 192.168.2.3 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 192.168.2.3 Primary WINS Server . . . . . . . : 192.168.2.3 Ethernet adapter WAN: Connection-specific DNS Suffix . : gateway.2wire.net Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet #2 Physical Address. . . . . . . . . : 00-11-43-D4-69-14 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 81.123.144.21 Subnet Mask . . . . . . . . . . . : 255.255.255.252 Default Gateway . . . . . . . . . : 81.123.144.22 DHCP Server . . . . . . . . . . . : 10.0.0.1 DNS Servers . . . . . . . . . . . : 10.0.0.1 Primary WINS Server . . . . . . . : 192.168.2.3 NetBIOS over Tcpip. . . . . . . . : Disabled Lease Obtained. . . . . . . . . . : 25 February 2011 22:56:59 Lease Expires . . . . . . . . . . : 25 February 2011 23:06:59 C:\Documents and Settings\Administrator>ping 192.168.2.11 Pinging 192.168.2.11 with 32 bytes of data: Reply from 192.168.2.11: bytes=32 time<1ms TTL=128 Reply from 192.168.2.11: bytes=32 time<1ms TTL=128 Reply from 192.168.2.11: bytes=32 time<1ms TTL=128 Reply from 192.168.2.11: bytes=32 time<1ms TTL=128

  Read the article

< Previous Page | 117 118 119 120 121 122 123 124 125 126 127 128  | Next Page >