Search Results

Search found 4141 results on 166 pages for 'router'.

Page 121/166 | < Previous Page | 117 118 119 120 121 122 123 124 125 126 127 128  | Next Page >

• Block a URL at browser level

  - by Farseeker

  Does anyone have a solution (that doesn't involve editing the hosts file) to block a particular URL from FireFox? Basic back story is that I'm trying to discipline myself. I'm spending FAR too much time over at Server Fault that I want to genuinely block the site from my work PC so that every time I find myself flicking to it during work time I can't see it, but I'd like to be able to disable it during my lunch break. (So I only spend 40 minutes a day there, rather than 4 hours). That said I don't want to block it at the router, nor for anyone else.

  Read the article

• Slash Notation IP - What is what?

  - by Nirmal

  We just signed up with a new ISP and we got a static IP from them. Our previous ISP just gave one IP and we were able to configure our web server using that. Now, we have got this new IP with a slash notation. This type is new to me. When I used the CIDR calculator, it gave me the following results: 202.184.7.52/30 IP: 202.184.7.52 Netmask: 255.255.255.252 Number of hosts: 2 Network address: 202.184.7.52 Broadcast address: 202.184.7.55 Can someone please help me by explaining what these are? I could not understand what the number of hosts means. Is that telling that I can use two different IP for DNS (A) records? Also, which one should I setup in my router? The network address or broadcast address? Thank you very much for any answer you may provide.

  Read the article

• European wireless data

  - by drewk

  I am on my way to Europe for 20 days with the wife and teenage kids. Among us, we have 3 iPhones, 1 Blackberry, 2 iPad 3G and 2 Macbook Pro laptops. Each has Skype. I am very concerned about AT&T data charges, and I am looking for a sensible alternative. For example, the AT&T data plans for the phones and iPads are $200 EACH for 200 MB per device. That is $1,200 and does not even cover the laptops. Ouch!!! I am thinking about a prepaid data plan from a European cell system of some sort combined with a GSM data modem and a Cradlepoint router, such as the CTR500. So, questions: 1) Anyone know of a GSM data source in Europe where I can buy a GSM Modem compatible with the CTR500 at a reasonable prepaid rate? 2) Experience with the CTR500?

  Read the article

• Newbie one: Virtual Networks - Hyper-V - Remote Destktop - Only one phisical NIC

  - by josecortesp

  Hello everyone, I'll try to explain my situation and I'll apreciate any help: I have a phisical server (quad core, 4Gb ram, 1TB raid 10, etc) with Win Server 2008 R2 enterprise, running IIS, Printing, etc... Also, I want to set up 2 virtual Servers with 2008 R2 standart one with SQL Server and the other with Team Foundation. What i need is: Being able to access from inside the private phisical network, to Remote Desktops on each of the Virtual and the phisical Servers Had Access from the outside, using a router and port Forwarding, to the TFS server and the IIS server (one is virtualized, the other is phisical) This is it, but note that I only have one Phisical Nic. How do I configure this to work. When i set up the hyper-v role, on the wizard something like it showed up but I don't remmember what i choose, and right now, I cannot access none of the servers from remote desktop, not even from the phisical private network. Can anybody point me, what can i do? Thanks in advance (sorry 4 my english, i'm a spanish talker and my english isn't that good)

  Read the article

• Drawbacks of installing linux on usb stick?

  - by Znarkus

  I am setting up a router/nas/http/whatever server based on an ION mini-ITX board. I've installed Ubuntu Server on an old 160 GB drive, but it generates a lot more heat and vibrates more than my other new drive (storage). It just doesn't fit the concept, and worse: it takes up a SATA port. As SSD's are crazy expensive I'm thinking of buying an extra 4 GB USB stick, and raid0 it. From my point of view, these are the pros/cons: Pros Low power consumption No vibrations No heat Smaller Get to buy new, larger USB stick (:D) Cons Shorter life time Slower Raid 0 More work maintaing/installing? I think the pros overweighs the cons. Shorter life time and raid 0 is countered by regular backups of the configs/settings. Slower is partially countered by raid 0, and I don't know about the last one. What do You think? Experience? Another solution?

  Read the article

• How to access website on localhost from internet?

  - by Nitesh Panchal

  Hello, I turned my pc into router by allowing port forwarding on port 80 and got my hostname(xyz.donexist.org) registered through dyndns.com. Now i when i type my public ip address in browser i get redirected to my browser. I have installed glassfish and have my website deployed in glassfish. I want that when i type xyz.donexist.org my website should be opened. What all steps more i need to take? I have made a entry in etc/hosts file as :- 127.0.0.1 xyz.donexist.org Please guide me. I am and beginner. Thanks in advance :)

  Read the article

• After installing Windows Phone 8 SDK, Connectify doesn't work

  - by Pratyush Nalam

  Today I installed Windows Phone 8 SDK from the official site. After installing and a couple of restarts (it restarted the PC to enable Hyper-V), I opened Connectify. I use Connectify Hotspot to connect my iPod to the internet as I have an ethernet connection and no wireless router. The problem is that now, Connectify doesn't show WiFi in Share Over. The attached screenshot shows this. Previously, before I installed the SDK, it would show Ethernet and Wi-Fi. I would select WiFi and share my internet. Now, this is completely screwed. EDIT: I found out that the Microsoft Virtual Wi-Fi Miniport Driver has got disabled and I am not able to enable it again. Please advise. Please advise on what to do Hardware: Windows 8 Pro with Media Center, Apple MacBook Pro 9,1 15 inch Mid-2012 (non retina)

  Read the article

• Window Servers 2003 Security After Support Lifecycle

  - by Daniel Fukuda

  Hello, I wanted to ask if let's say that Microsoft has stopped supporting Windows Server 2003 now so there is no any security updates and I use that system for Domain Controller (Windows XP/7 Professional Clients) and File Server only + I'm using ESET NOD23 AntiVirus. Will my system be secure? I'm asking because I don't surf internet on that system nor I will install/open any programs/documents and that server is connected to router without any open ports. "On July 14, 2015, all Windows 2003 support, including security updates and security-related hotfixes, will be terminated."

  Read the article

• Windows Server 2008 Active Directory DNS setup

  - by Mister IT Guru

  I have to setup a small windows network inside my bigger linux/mac infrastructure. In order to get the windows clients logging onto the domain, I have had to make the DC their primary DNS server, which seems to have worked. I would much prefer to have one DNS server running on my network, or at least one authoritative server running on the network. I have a USG 200 router/firewall and I can configure some static records for DNS, but I an not sure what I need to put in order to get DNS and AD working together, and hints and tips appreciated.

  Read the article

• Certain users cannot get to my server

  - by Zeno

  I am finding more and more users that report they cannot reach my server (website or services). Their tracert from that user looks like this: Tracing route to domain.com [*.*.*.255] over a maximum of 30 hops: 1 * * * Request timed out. The server is up and functional and every else reports it is fine. But there are various users who cannot get to it. I have no firewall or anything that would block anyone. Yes, the last part of the server IP is 255. Could this be causing it? http://www.dslreports.com/forum/r18539206-Last-octet-255-bug-on-Windows Or would a certain ISP be denying traffic to my server? Or something on their router level?

  Read the article

• Why not all users can log in to a network computer by using <network computer name>/<user name> form

  - by Haris

  There is a file server in my office that is not connected to my office LAN. In this server there are folders that are shared. This server is connected to a switch and a wireless router. Everyone who wants to access this server uses wireless network connection. They log in to this server by providing user name and password registered to the server. Some people can log in to my office file server by providing user name in (the server name)/(user name) format, while other must use (the server IP address)/(user name) format. Why is it like this? I need everyone can access the file server by providing user name in (the server name)/(user name) format. I have tried to change the %SystemRoot%\system32\drivers\etc\hosts file, as some suggested, but it won't work. Any other suggestion?

  Read the article

• Nodes inside Cisco VPN. Incoming SSH requests allowed. But can't initiate an outbound SSH.

  - by Douglas Peter

  I've a gateway-to-gateway VPN setup between my Linksys RV042 router and a Cisco VPN. I am able to SSH into any of the machine inside the VPN from my network. But none of the machines inside the VPN can initiate an SSH into my network. It seems they've blocked even all ping requests to my network gateway. This is the requirement: I have scripts that SSH into the machines inside the VPN and run a long mysql query. The query generates an output to a file. The time that these queries take is variable. So I have a loop in my machine that periodically SSHes into the VPN machine and checks if the query has finished, and pulls the generated file using SCP. I need to simplify it thus: The script will run at the machine inside the VPN, and when the query completes, it will SSH into my machine and pushes the generated file. Thanks for any ideas.

  Read the article

• windows 7 wireless knocks off other computers on the network

  - by Sean

  I am trying to fix a wireless network issue. When a new windows 7 machine (we have 2 in the house) we have problems with any other windows xp machines connecting to the wireless network. I am using a linksys WRT110 running Firmware Version: 1.0.04 (which is not the latest firmware its Ver.1.0.07 but the router would not use the bin update file). I have tried a ton of variations in setting for the wireless network, changed the channel, the security level (none, wep wpa, wpa2), network type (g,bg mixed). I have also read some stuff about homegroup settings for windows 7 but have not seen any differences that make a difference. Basically windows 7 does not like to connect to our network but when I manage to get it to work the windows xp pro machines get kicked off. The windows xp pro machines are a few years old but both windows 7 machines are less than 6 months old.

  Read the article

• Updating Cisco VPN config to add vpnc support

  - by Igor Kuzmitshov

  I have a Cisco 1841 configured for VPN connections of two types: Peer-to-peer for partners' routers (IPsec) — using different crypto isakmp key and crypto map with set peer, set transform-set, match address for every peer (same map name, different priorities). That crypto map name is added to the WAN interface. Client access (PPTP) — using vpdn-group with accept-dialin protocol pptp. Now, a new partner wants to connect using vpnc client. The latter needs IPSec ID (group name) and IPSec secret in addition to username and password. I guess that IPSec secret is pre-shared key that can be specified in crypto isakmp key on Cisco. But I could not find any VPN tutorials involving groups. Hence, my questions: How to add IPSec ID (group name) and IPSec secret on Cisco router for vpnc connections? Should I add a new crypto map matching all addresses as well? Is it possible to add this configuration without breaking the existing setup? Thank you.

  Read the article

• Rewrite URL based off of IP on OpenWRT

  - by Scott

  We are running OpenWRT on a WRT54GL. I have been looking for an answer to this, but I can't seem to figure out what to search for, if its possible, or what combination of programs to use. I want to be able to redirect a HTTP request from a WiFi device based off of their MAC address. This should all be transparent to the device. Basically we are trying to redirect any non-registered devices to a website to register the device (at this point, we would push a new config to the router that would allow this MAC address "full access"). Once a device is registered, it will be redirected to a transparent squid proxy server on another machine for caching/blocking certain sites. I looked at tinyproxy - popilo which redirects but I won't have the MAC address to know if its registered or not. Any help (google suggestions, programs, anything!) would be very much appreciated!

  Read the article

• L2TP server - site-to-site vpn connection

  - by Pyro

  I am not sure this is the right place for this question but here goes. We want to connect users using an L2TP VPN connection to a users at the other end of a SonicWall site-to-site VPN. Currently we have a SonicWall firewall/router contraption in the home-office that is connected to a far-office over a VPN. Communications with machines in the home-office and far-office is fine. We also have an L2TP server running on the SonicWall that outside users can connect to. This gives them access to machines in the home-office. Communication between outside users and the home-office is fine. However outside users connected to the home-office via the L2TP server can't communicate with machines in the far-office. Will there need to be network bridging or routing needed? Or will this simply be a firewall setting to get this working? Thanks for any help or clues you provide! Rob

  Read the article

• Reconnect feature in Jdownloader for BSNL broadband

  - by pragadheesh

  Hi, I recently downloaded JDownloader for downloading from RS. But clicking the Reconnect icon in toolbar gives the error, "Reconnect failed. Please try manual reconnect". :( In the reconnection settings, there is an entry for Router's IP. and the rest(User,pwd, Reconnection script) are blank. I having BSNL dataone broadband connection in Bangalore. I connect to internet just by turning on the modem and no user name and password is required. How can i allow Reconnection feature in JDownloader.? If a reconnection script is required how to write the script.? Badly in need of this. Thanks in advance.

  Read the article

• Hostname problems in CentOS 5.5

  - by spoon16

  I just set up a CentOS 5.5 machine on my local network and attempted to modify the hostname by editing /etc/sysconfig/network file. When I'm logged in locally the change to the hostname is reflected and seems to be working fine. When I open a SSH session via PuTTY from Windows this is what I see at the prompt: [root@? ~]# cat /etc/sysconfig/network NETWORKING=yes NETWORKING_IPV6=yes HOSTNAME=mini.local [root@? ~]# sysctl kernel.hostname kernel.hostname = ? [root@? ~]# hostname ? [root@? ~]# hostname -f hostname: Unknown server error A couple of other symptoms that may be helpful in troubleshooting this problem. I can ping the CentOS box from my Windows machine via IP but not hostname. Also, my Netgear router does not display the hostname when I view the "Connected Devices", I do see the mac address and the proper IP listed though. How can I make it so that the hostname is properly propagated throughout my network?

  Read the article

• Configuring NAT and static IP on Cisco 877W

  - by David M Williams

  Hi all, I'm having trouble setting up a static IP reservation on a network. What I want to do is assign IP 192.168.1.105 to MAC address 00:21:5d:2f:58:04 and then port forward 35394 to it. If it helps, output from show ver says Cisco IOS software, C870 software (C870-ADVSECURITYK9-M), version 12.4(4)T7, release software (fc1) ROM: System bootstrap, version 12.3(8r)YI4, release software I have done this - service dhcp ip routing ip dhcp excluded-address 192.168.1.1 192.168.1.99 ip dhcp excluded-address 192.168.1.200 192.168.1.255 ip dhcp pool ClientDHCP network 192.168.1.0 255.255.255.0 default-router 192.168.1.1 dns-server 192.168.1.1 lease 7 ip dhcp pool NEO host 192.168.1.105 255.255.255.0 hardware-address 0021.5D2F.5804 ip nat inside source static tcp 192.168.1.105 35394 <PUBLIC_IP> 35394 extendable However, the machine is getting assigned IP address 192.168.1.101 not .105 ... any suggestions? Thanks !

  Read the article

• routing wiredness - traceroute 'vanishes' en route

  - by The Journeyman geek

  I'm attempting to set up one of my boxes as a server (again), but i'm having some odd connection issues- the box itself connects fine to the internet, but trying to connect to my external ip address seems to result in the trace getting 'lost' partway. http://pastebin.com/HCQAGbvn - this is a traceroute from another system that's connected to another ISP - starhub is my own one, while i have another system that i have access to on singtel. I'm wondering if my ISP is messing around with routing, or is something very odd going on. As you note, the traceroute dosen't reach me, but if it helps, i use a dd-wrt router.

  Read the article

• CentOS connect to the internet

  - by Delirium tremens

  I installed CentOS, but it didn't automatically connect to the internet. Is that the normal behavior? I have Ethernet Broadband Router DI-604 and WebStar DPX2203 series Cablemodem with EMTA . What should I do to connect to the internet? Update: A cousin told me my ethernet adapter or network board will depend on my motherboard. My computer upgrade document says the motherboard is gigabyte video onboard. I heard gigabyte's network adapters are Gigabit or Realtek. In CentOS, System - Administration - Network - New - Ethernet, first, only "Other Network Board" was listed, so I selected it and clicked Next, then there wasn't Gigabit, but there was Realtek, so I selected Realtek. I heard with Net Virtua selecting dhcp the things first answered asked me to tell first answerer are automatically configured. So I tried Realtek with dhcp, but it still didn't work.

  Read the article

• OSX Server 3, Mac clients binding to OD and Profile Manager failing

  - by dbf

  I've made a setup containing a Mac Mini with OSX Server 3 (Mavericks 10.9.2) using Open Directory and Profile Manager (Mail, etc all set up and working). Now the thing is, internally on the local network, everything works great. Clients can bind to the OD and the users are able to login. I can install trust and settings profiles (either custom or group profiles) and all services in the profiles mentioned are being configured correctly. I can log in and out, hump around and do it a 100 times on different macs with different users, it works. My goal is to make this service publicly. The domain is with a FQDN which I own, for simplicity let's say server.domain.com. Now the only way for me to bind the clients to the OD is using LDAP mapping RCF2307 (without SSL) and a DN suffix of dc=server,dc=domain,dc=com using the Directory Utility. The options from server, or open directory will throw several errors like Connection failed to node '/LDAPv3/server.domain.com (2100). First of all I don't really understand the problem why clients can't bind to the OD like it does locally, with and without SSL (all ports are open, literally all ports are open, not just 389,636 and 1640, wasn't sure if I was missing any). When the clients are using LDAP mapping RFC2307 to bind (without SSL only), clients are able to authenticate, login and even load the Trust profile. But every Settings profile will fail with a Debug Message: Unable to find GUID in user record OD or fail to install saying missing user identification. Is there any way to get this to work without RFC2307? Because there is quite some stuff missing when using RFC2307 and not pull the mapping from the server or use open directory. Is this setup even possible? Or should I use VPN to authenticate with the OD? The network setup is a Modem/Router (DHCP off) with WAN NATted to an Airport Extreme (Using DHCP+NAT). The AE does notify with a double NAT message but I haven't had any problems with it on any other service. So WAN - 192.168.2.220 (static), AE - 10.0.1.* (dhcp) Output of DIG from the outside using dig server.domain.com ;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;server.domain.com. IN A ;; ANSWER SECTION: server.domain.com. 77 IN A 91.50.*.* (valid WAN IP) ;; SERVER 172.*.*.1#53(172.*.*.1) (iPhone) DIG locally from a client and server (same output) ;; flags: qr aa rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 2, ADDITIONAL: 0 ;; QUESTION SECTION: ;server.domain.com. IN A ;; ANSWER SECTION: server.domain.com. 10800 IN A 10.0.1.11 ;; AUTHORITY SECTION: server.domain.com. 10800 IN NS domain.com. (used for email send in relay) server.domain.com. 10800 IN NS server.domain.com. ;; SERVER 10.0.1.11#53(10.0.1.11) Are there any things I should check? Only have OSX. -- double NAT issue, plugged in the server directly on the Modem/Router with a static IP and issue remains. Guess that rules out the double NAT thing. -- changeip -checkhostname comes with There is nothing to change, e.g. success. Primary address = 10.0.1.11 Current HostName = server.domain.com DNS HostName = server.domain.com For now, I've made a workaround by using an admin account that forces a permanent VPN connection on boot. That means before it comes to the login, a connection is already made or underway. I will continue this post when I have more time, also locating all the necessary .log files of each application involved. I have some suspicions but have to debug a bit more when I have more time on my hands .. Unless, of course, I get sidetracked with having a life. Which is arguably not very likely. krypted.com

  Read the article

• Discover MAC address

  - by Kami

  I've to setup a bunch of server ! I need to discover their mac address with the following situation : MacBookPro >----------< Server I'm directly connected (not behind a router/switch) to the server. I've no clues about the ip address the server is using as default setup. I can't use a display connected to the server displaying its newtwork card config. How can I discover the MAC address of the server network card ? I'm looking for a command line tool. If something exists in MacPort it's also ok !

  Read the article

• Can I turn my Mac Mini into a Wi-Fi Hotspot without additional tool

  - by user262325

  Hello everyone I have an app need to test via wifi. I just wonder if there is a way to turn my Mac Mini into a Wi-Fi Hotspot without additional tool. I try to setup airport new network name is"mymacmini'. My iPod Touch also can recognize the network "mymacmini". I set my iPod wifi as "mymacmini" But if I try to connect to Internet, Safari always reports failure and connnection with Wifi. I hope to know if I need purchase a wireless router for MAc Mini or there are something wrong I did above? Thanks interdev

  Read the article

• Mails bounce because of invalid character ('@') in username

  - by user1598585

  I have a working exim setup with virtual users, working alright, except for when I try to send email to certain servers. These servers reject my emails because of #5.1.3 Invalid character ('@') in username. The offending header parts seem to be: Return-path: <"[email protected]"@smtp.example.com> and ...(envelope-from <"[email protected]"@smtp.example.com>)... The problem is that I cannot find where and why the usernames are being generated like this. My router for submission is: dnslookup: driver = dnslookup domains = ! +local_domains transport = remote_smtp ignore_target_hosts = 0.0.0.0 : 127.0.0.0/8 no_more And the respective transport: remote_smtp: driver = smtp What can be producing this problem?

  Read the article

< Previous Page | 117 118 119 120 121 122 123 124 125 126 127 128  | Next Page >