Search Results

Search found 8923 results on 357 pages for 'wireless keyboard'.

Page 121/357 | < Previous Page | 117 118 119 120 121 122 123 124 125 126 127 128  | Next Page >

• wireless dropping out

  - by Sam

  My wireless network connection is dropping out and its driving me nuts. It is weird because it happens at totally random intervals and other devices work while my computer has been dropped. Both my USB dongle and wifi card randomly disconnect from the router and I am unable to connect for a couple of minutes. It is especially irritating because two different adapters are failing at the same time, sounds like a software problem to me, but where? Both my laptop and iPod remain connected when the connection drops. What on earth is happening? I doubt its the router because the other devices would disconnect as well.

  Read the article

• why only google related sites load using wireless network

  - by gansai

  I have a wireless internet connection through BSNL. I have a windows 7 ultimate, and using latest Google chrome. During night time ie from 12:30 am onwards till around 5:30 am, I have the following problem: Only the following webpages load: Google Search Google images and all related to google product pages like you see them on the google home page. Blogspot webpages as supported through Google. Any other site loading gets stuck with the status message:- Waiting for www.thaturl.com .... And it goes on and on. Why does this happen? I checked around googling for this but no solution at all. By the way I tried changing my dns addresses too sometimes from automatically to opendns and then Google public dns. I need some solution which might help me to load other websites also. Thanks in advance.

  Read the article

• Stream computer screen to TV via network instead of a USB wireless link

  - by user24559

  I want to stream my computer screen (not just video or a limited amount of content) to my TV via the network. I know there are wireless devices that use USB to tranfer the screen to the TV. However, these are limited to a short distance. What I want to do is stream the data via the network so I can be anywhere within the network and have the data shown on the tv. I am looking for video and sound to transfer. I want the entire computer screen to transfer just like when you connect the computer to the tv via VGA or HDMI and the sound out using the 3.5mm plug. I have been unable to find a unit that allows for the entire computer screen to transfer via the network. I just find the ability to stream video. I am using Windows 7 Ultimate with a quad processor and 16 GB of memory so I have the power to handle the transfer. My tv is hdtv.

  Read the article

• Citrix XenApp application does not have keyboard focus when launched

  - by Jason Pearce

  On new or existing Citrix XenApp 4.5 servers, I am having problems streaming the Allscripts Pro EHR application via the XenApp web interface. When users launch the application via the Citrix XenApp web interface, the application does not have focus, preventing users from typing in their username and password. If they use their mouse to select either the username or password fields, they still cannot enter any text. However, if they do any of the following actions, they can then enter in their username and password and the application runs without problems: Click on the Login button with empty fields. Logon fails but they can then enter their credentials. Minimize the login window and then maximize it. They can then gain keyboard focus to enter their credentials. What might be preventing this particular application from having focus when it launches?

  Read the article

• find wireless-repeater ip (router)

  - by Brtrnd

  Really long time ago I set up my dd-wrt router up as a repeater. It works well; in the summer I place it near the garden and I have wifi in the garden. I would like to revisit te settings and see if it would be a good idea to install openvpn. The problem is: I don't remember the ip of the router. I probably followed the setup instructions on the dd wrt wiki. it doesn't show up on the management-console of my main router (a docsis3 modem); it doesn't show up if I do an IP scan of the whole class B; it doesn't show as the gateway when i connect to it (wired or wireless). Any ideas on how I could find the web-interface?

  Read the article

• Setting up Edimax EW-7206APg as Universal Repeater

  - by Ondra Žižka

  Hi, I've troubles setting up Edimax EW-7206APg as a Universal Repeater. I've read few manuals, but they are unclear on certain points. I've managed the repeater to get to a state when it's in a "connected" state. I've set the same WPA passphrase as the router has because I haven't seen any other place to set it at. These are my settings: System Uptime 0day:1h:33m:11s Hardware Version Rev. A Runtime Code Version 1.32 Wireless Configuration Mode Universal Repeater ESSID edimax Channel Number 6 Security WPA-shared key BSSID 00:c0:9f:40:bd:38 Associated Clients 0 Wireless Repeater Interface Configuration ESSID Dusan Security WPA BSSID 00:4f:62:23:8f:7e State Connected LAN Configuration IP Address 192.168.0.10 Subnet Mask 255.255.255.0 Default Gateway 192.168.0.1 MAC Address 00:c0:9f:40:bd:37 This is ipconfig /all: Prípona DNS podle pripojení . . . : riomail.cz Popis . . . . . . . . . . . . . . : Intel(R) PRO/Wireless 2200BG Network Connection Fyzická Adresa. . . . . . . . . . : 00-0E-35-3D-77-68 Protokol DHCP povolen . . . . . . : Ano Automatická konfigurace povolena : Ano Adresa IP . . . . . . . . . . . . : 192.168.0.5 Maska podsíte . . . . . . . . . . : 255.255.255.0 Výchozí brána . . . . . . . . . . : 192.168.0.1 Server DHCP . . . . . . . . . . . : 192.168.0.1 Servery DNS . . . . . . . . . . . : 94.74.192.252 94.74.192.244 I can ping the repeater, I can ping the root AP, but not a DNS server or any other IP beyond the root AP. Anyone has an idea what's wrong? Thanks, Ondra

  Read the article

• Synergy 1.4.2 Linux server, OSX client, Media/Function key mapping issues

  - by at165dB

  I'm using an Apple bluetooth keybord to control my Linux synergy server. SSH tunneling, Mouse, Keyboard, and Copy&Paste all work. Linux sees all the media/app keys that are on top of the F# keys correctly. However if I press any of those keys while controlling my OSX client, nothing happens on the client. Running synergys with -d DEBUG1 I can see the following keycode info: Pressing the "dim monitor" key that also serves as F1 generates: new mask: 0x2000 event: KeyPress code=232, state=0x0010 new mask: 0x2000 If I press "fn" and the same key, I can see it sending what I'm assuming is an F1: event: KeyPress code=67, state=0x0010 onKeyDown id=61374 mask=0x2000 button=0x0043 send key down to "foo.cisco.com" id=61374, mask=0x2000, button=0x0043 new mask: 0x2000 event: KeyRelease code=67, state=0x0010 onKeyUp id=61374 mask=0x2000 button=0x0043 send key up to "foo.cisco.com" id=61374, mask=0x2000, button=0x0043 I'm guessing I need to tweak my synergy.conf so that the server sends keys that it currently isn't. I'm also not sure what I need to do to tweak the keys that it is sending, but are not working. Below are all the other keys I'm having issues with. Does anyone have any idea how I can enable their functionality? brighten monitor: new mask: 0x2000 event: KeyPress code=233, state=0x0010 new mask: 0x2000 expose: new mask: 0x2000 event: KeyPress code=128, state=0x0010 new mask: 0x2000 dashboard: new mask: 0x2000 event: KeyPress code=212, state=0x0010 new mask: 0x2000 dim keyboard: new mask: 0x2000 event: KeyPress code=237, state=0x0010 new mask: 0x2000 brighten keyboard: new mask: 0x2000 event: KeyPress code=238, state=0x0010 new mask: 0x2000 rewind: event: KeyPress code=173, state=0x0010 onKeyDown id=57521 mask=0x2000 button=0x00ad send key down to "foo.cisco.com" id=57521, mask=0x2000, button=0x00ad new mask: 0x2000 event: KeyRelease code=173, state=0x0010 onKeyUp id=57521 mask=0x2000 button=0x00ad send key up to "foo.cisco.com" id=57521, mask=0x2000, button=0x00ad play/pause: event: KeyPress code=172, state=0x0010 onKeyDown id=57523 mask=0x2000 button=0x00ac send key down to "foo.cisco.com" id=57523, mask=0x2000, button=0x00ac new mask: 0x2000 event: KeyRelease code=172, state=0x0010 onKeyUp id=57523 mask=0x2000 button=0x00ac send key up to "foo.cisco.com" id=57523, mask=0x2000, button=0x00ac fastforward: event: KeyPress code=171, state=0x0010 onKeyDown id=57520 mask=0x2000 button=0x00ab send key down to "foo.cisco.com" id=57520, mask=0x2000, button=0x00ab new mask: 0x2000 event: KeyRelease code=171, state=0x0010 onKeyUp id=57520 mask=0x2000 button=0x00ab send key up to "foo.cisco.com" id=57520, mask=0x2000, button=0x00ab mute: event: KeyPress code=121, state=0x0010 onKeyDown id=57517 mask=0x2000 button=0x0079 send key down to "foo.cisco.com" id=57517, mask=0x2000, button=0x0079 new mask: 0x2000 event: KeyRelease code=121, state=0x0010 onKeyUp id=57517 mask=0x2000 button=0x0079 send key up to "foo.cisco.com" id=57517, mask=0x2000, button=0x0079 volume down: onKeyDown id=57518 mask=0x2000 button=0x007a send key down to "foo.cisco.com" id=57518, mask=0x2000, button=0x007a new mask: 0x2000 event: KeyRelease code=122, state=0x0010 onKeyUp id=57518 mask=0x2000 button=0x007a send key up to "foo.cisco.com" id=57518, mask=0x2000, button=0x007a volume up: event: KeyPress code=123, state=0x0010 onKeyDown id=57519 mask=0x2000 button=0x007b send key down to "foo.cisco.com" id=57519, mask=0x2000, button=0x007b new mask: 0x2000 event: KeyRelease code=123, state=0x0010 onKeyUp id=57519 mask=0x2000 button=0x007b send key up to "foo.cisco.com" id=57519, mask=0x2000, button=0x007b eject: event: KeyPress code=169, state=0x0010 onKeyDown id=57345 mask=0x2000 button=0x00a9 send key down to "foo.cisco.com" id=57345, mask=0x2000, button=0x00a9 new mask: 0x2000 event: KeyRelease code=169, state=0x0010 onKeyUp id=57345 mask=0x2000 button=0x00a9 send key up to "foo.cisco.com" id=57345, mask=0x2000, button=0x00a9

  Read the article

• iPhone Keyboard hiding fields in UIWebView

  - by Pete

  Hi, I am a beginner at iPhone development and am hoping someone can help me with my question. I have a UIWebView displaying a web page. If the user taps inside a textbox on the web page then the keyboard pops up. This is great, but it hides the field that the user tapped on. I have looked around and found code samples to deal with this, but none that specifically deal with the UIWebView. I have implemented UIKeyboardDidShowNotification and UIKeyboardDidHideNotification but am not sure how to resize the UIWebView properly. I have tried putting the UIWebView in a UIScrollView but not had any success with that. The code below seems to adjust the UIWebView but won't let it scroll to the field. -(void) keyboardDidShow: (NSNotification *)notif{ if (keyboardShown) return; NSLog(@"Keyboard Show"); NSDictionary *info = [notif userInfo]; NSValue *aValue = [info objectForKey:UIKeyboardBoundsUserInfoKey]; CGSize keyboardSize = [aValue CGRectValue].size; CGRect viewFrame = webBrowser.frame; viewFrame.size.height -= keyboardSize.height; webBrowser.frame = viewFrame; keyboardShown = YES; } -(void) keyboardDidHide: (NSNotification *)notif{ NSLog(@"Keyboard hide"); keyboardShown = NO; } Hopefully someone can help me or point me in the right direction. Thanks! Pete

  Read the article

• Part of my layout goes upward with keyboard

  - by Burak Dede

  My android app have a layout like this when i open keyboard two imageview at the bottom of the page shows up over the keyboard , i couldnt see the problem why it goes upward with the keyboard can you help me about this ? <?xml version="1.0" encoding="utf-8"?> <RelativeLayout xmlns:android="http://schemas.android.com/apk/res/android" android:layout_width="fill_parent" android:layout_height="fill_parent" > <LinearLayout android:id="@+id/searchLinear" android:layout_width="wrap_content" android:layout_height="wrap_content" android:background="@color/upperbackground"> <EditText android:id="@+id/searchBox" android:layout_alignParentTop="true" android:layout_width="fill_parent" android:layout_height="wrap_content" android:singleLine="true" android:layout_margin="12dip" android:paddingLeft="35dip" android:textSize="15sp" android:background="@drawable/search_bar"/> </LinearLayout> <LinearLayout android:id="@+id/searchButtons" android:layout_below="@id/searchLinear" android:orientation="horizontal" android:layout_width="fill_parent" android:layout_height="wrap_content" android:gravity="center_vertical|center_horizontal" android:background="@color/upperbackground"> <ImageView android:id="@+id/btnSukela" android:layout_width="wrap_content" android:layout_height="wrap_content" android:clickable="true" android:focusable="true" android:onClick="sukelaClickEvent" android:paddingRight="8dip" android:paddingBottom="5dip" android:src="@drawable/sukela"/> <ImageView android:id="@+id/btnSearch" android:layout_width="wrap_content" android:layout_height="wrap_content" android:layout_toRightOf="@+id/btnSukela" android:clickable="true" android:focusable="true" android:onClick="searchEntryClickEvent" android:paddingLeft="8dip" android:paddingBottom="5dip" android:src="@drawable/search"/> </LinearLayout> <RelativeLayout android:id="@+id/bottomLinear" android:layout_alignParentBottom="true" android:orientation="horizontal" android:layout_width="fill_parent" android:layout_height="wrap_content" android:gravity="center_vertical|center_horizontal" android:background="@drawable/bottom_back"> <ImageView android:id="@+id/btnToday" android:src="@drawable/today" android:background="@color/bottombackground" android:layout_width="wrap_content" android:layout_height="wrap_content" android:layout_alignBottom="@+id/bottomLinear" android:layout_marginBottom="19dip" android:layout_centerVertical="true" android:clickable="true" android:focusable="true" android:onClick="todayClickEvent"/> <ImageView android:id="@+id/btnPopular" android:src="@drawable/popular" android:background="@color/bottombackground" android:layout_toRightOf="@+id/btnToday" android:layout_width="wrap_content" android:layout_height="wrap_content" android:layout_centerVertical="true" android:clickable="true" android:focusable="true" android:onClick="popularClickEvent"/> </RelativeLayout> <RelativeLayout android:layout_width="fill_parent" android:layout_height="fill_parent" android:layout_below="@+id/searchButtons" android:layout_above="@+id/bottomLinear" android:background="@color/background"> <ListView android:id="@android:id/list" android:layout_width="fill_parent" android:layout_height="wrap_content"/> </RelativeLayout> </RelativeLayout>

  Read the article

• Keyboard blocking my view

  - by John Smith

  I have a UIView with another UIView inside it. On the inside UIView there is a textbox which I want to fill in. When I try to fill it in the keyboard blocks my view: The UIViewController has the following containerView = [[UIView alloc] initWithFrame:[UIScreen mainScreen].bounds]; self.view=containerView; //The apropriate releases etc are further on... When I touch it, the keyboard comes up as expected, but blocks the textbox I'm trying to fill in. How can I force the view to slide up? The front view OptionsFront * fv = [[OptionsFront alloc] initWithFrame:[UIScreen mainScreen].bounds]; [containerView addSubview:frontView]; In the front view is a subview CGRect bounds = CGRectMake(0.0f, 210.0f, 280.0f, 130.0f); sv = [[UIView alloc] initWithFrame:bounds]; [self addSubview:sv]; //added to frontView In sv is a textbox near the botton: rect = CGRectMake(70.0f, 20.0f, 100.0f, 27.0f); cf = [self createTextField_Rounded:rect holder:@"+ve"]; [sv addSubview:cf]; So cf happens to be near the bottom of the page. I expected that when I select it, the whole display would move up, but the keyboard just moves up and blocks it. What can I do? Appendix: - (UITextField *)createTextField_Rounded:(CGRect) frame holder:(NSString *) ph { UITextField *returnTextField = [[UITextField alloc] initWithFrame:frame]; returnTextField.borderStyle = UITextBorderStyleRoundedRect; returnTextField.textColor = [UIColor blackColor]; returnTextField.font = [UIFont systemFontOfSize:17.0]; returnTextField.delegate = self; returnTextField.keyboardType = UIKeyboardTypeNumbersAndPunctuation; returnTextField.returnKeyType = UIReturnKeyDone; returnTextField.clearButtonMode = UITextFieldViewModeWhileEditing; return returnTextField; }

  Read the article

• Wireless router blocking some sites while using ethernet is fine

  - by Micke

  I'm using Windows 7 and my router is a wireless Apple Airport Express that is approximately two years old. Suddenly I can't access some sites (for example www.sthlm.friskissvettis.se, or www.vegetarian-shoes.co.uk, some streamed tv-shows on svtplay.se, and a number of other random sites) when connecting to internet with my router. It worked good until recently and I'm fairly sure this problem emerged when my ISP upgraded from 10/10mbit to 100/10mbit speed. Most other sites like facebook and google works fine. When using my network cable to connect to internet everything works fine and I can access these sites. Firmware is current and I've tried reseting the router to factory defaults. Tried different browsers, and I can't ping the "blocked" sites either. Tracert www.sthlm.friskissvettis.se starts with 10.0.0.1 and continues through a number of long addresses until it says timeout. The last working address before timeout was sth-tcy-ipcore01-ge-0-2-0.neq.dgcsystems.net [83.241.252.13], if it matters. Tracert www.vegetarian-shoes.co.uk also eventually gives me a timeout. When the network cable is plugged in, I still get timeout on tracert www.sthlm.friskissvettis.se even though I can access the site in Chrome. Weird. www.vegetarian-shoes.co.uk doesn't give me a tracert timeout when the cable is plugged in, and I can access the site as usual. I've tried changing DNS servers to use opendns servers instead, but to no use. I've tried pinging these two sites with a lower MTU packet size (with this method: http://www.richard-slater.co.uk/archives/2009/10/23/change-your-mtu-under-vista-or-windows-7/), but still can't access them through ping... I don't know what to do anymore.... any suggestions???

  Read the article

• Linksys wireless router will not hardware reset.

  - by Jack M.

  Hello, all. I'm unable to make my router perform a hardware reset, and I cannot understand why. All was working well, except that my iPhone could not connect to the wireless. I found that the router was only allowing AES encryption on WPA2 Personal mode, so I upgraded the firmware. I updated the firmware to Ver.1.06.1, and everything went screwy. The router is no longer showing up in the WiFi list (as Linksys, or its previous network name). Wiring into the router gives me an IP address from my ISP (24.121.121.XXX). Attempting to do a hardware reset, but the power light never starts flashing and the router does not seem to reboot. My machine wired in is still online with no interruption in WoW. Pulling the power cord to force a reset returns it to the same state. I even went so far as to pull up my previous IP address (from DynDNS) and try to connect to that, but it wont even ping. What I'm trying to find out is: Did the new firmware fry the thing, or is there some way to fix this? Thanks in advance for any help.

  Read the article

• Configure a Windows PC as network appliance w/o monitor, keyboard and mouse

  - by Joshua Lim

  I intend to use a small form factor PC with Windows 7 Professional installed as a network appliance attached directly to my customer's LAN without connecting a monitor, keyboard or mouse. How should I configure the networking for my PC so that I can access it via say my laptop? I figure that I can do it 2 ways. Attach my laptop to the PC using a crossover cable? Connect via RDP and configure networking. Configure an IP address on the PC before I deliver it to the customer place. At the customer's place, attach the PC to LAN and connect to the IP address which I previously configured from my laptop or from one of the customer's workstations. I know the first way is doable, but is the second way possible? I'm sorry if this question sounds ridiculous - I am Delphi programmer but a novice on networking. Finally, if possible, I hope to make the configuration process web based as I wouldn't like to reveal the fact that I am using Win7 Pro for the network appliance!

  Read the article

• Ubuntu odd mouse and keyboard behavior when window gains inner focus

  - by Scott

  This morning on my Ubuntu 10.10 system when I open a window - for example, system-preferences-about me, if I click in to a field such as "work email", I can no longer close the window with the mouse! Clicking the X on the window will not work. Also, I loose the ability to click on anything else - clicking on the desktop, icons, menus, workspaces, etc. do not work. Even the effect when you hover over a folder on the desktop and that folder highlights - that stops until the window is closed. If I open this same screen but do not click in to a field, everything is fine - I can close the window with the X and everything else works fine. Same thing happens with several other windows I tried. Even calculator - I can open it, everything is fine until I click on a button in the calculator - then no ability to click on anything else. Have to Alt-F4 to close the window. The system is only about a week old from a fresh install (64 bit ubuntu - quad core amd machine). I uninstalled wine, turned off remote desktop/disabled in startup, also in startup disabled visual assistance, bluetooth, dropbox, klipper. Reboot, no difference. The only other thing non-standard I see in startup is nvidia. Using a logitec usb mouse, saitek usb keyboard. Was working fine yesterday. I can not think of anything I did / installed yesterday. I switched themse, then went to update manager and saw two x server / x org related updates and installed them, reboot and NOW IT IS FINE! However, then I re-enabled dropbox, klipper and remote desktop rebooted and the problem is back. Again I disabled and rebooted. Problem is still there!! So somehow I fixed it at least for a few minutes, but now it is back and I am out of ideas.

  Read the article

• Microsoft Mouse and Keyboard Center - Slow response for App-specific shortcuts

  - by Darrel Hoffman

  So a few months ago, I bought a new MS mouse, and was surprised that they'd discontinued Intellipoint in favor of this Microsoft Mouse and Keyboard Center. It seems to have the same functionality underneath all the bloat, but there's a very serious drawback - when I set up application-specific functions for the extra buttons on the mouse, they work, but sometimes with a very long delay, like up to a minute or more. For example, I often set up the left side button as an "Undo" in various programs for convenience. But sometimes, when I try to use that Undo button, nothing happens, so I'm forced to use the standard Ctrl-Z or whatever. But then, a minute or so later, it suddenly remembers that I hit that button a while back, and calls the Undo unexpectedly on something entirely different. It's infuriating. No modern computer function should be this slow. It's not the software or the computer itself, because doing an Undo via Ctrl-Z or the menu still works instantly. It's very definitely a side-effect of delayed response to the mouse button. Usually after it delays the first time, it'll work quickly after that, but if you haven't used a given shortcut in several minutes, it "forgets" again and you get another inexplicably long delay. Intellipoint never had this problem, but it's not supported any more, and not compatible with the newer mice. Has anyone else noticed slow-downs with MS M&K C and app-specific shortcuts? Any ideas how to get around this? I use these shortcuts extensively in my workflow and it's just entirely unacceptable to have such a long delay in what should be a pretty basic feature.

  Read the article

• Ubuntu - wireless connection works great but wired is totally dead

  - by Dan

  I am running Ubuntu 10.04 on my Acer Aspire One netbook. The wireless connection works great, but the wired is totally dead. When I plug the Ethernet wire, the little led next to the port doesn't blink. If I do ifconfig, this is the output: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1659 errors:0 dropped:0 overruns:0 frame:0 TX packets:1659 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:132304 (132.3 KB) TX bytes:132304 (132.3 KB) wlan0 Link encap:Ethernet HWaddr 18:f4:6a:65:48:1f inet addr:192.168.1.7 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::1af4:6aff:fe65:481f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:94823 errors:0 dropped:0 overruns:0 frame:0 TX packets:81390 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:93028474 (93.0 MB) TX bytes:18002558 (18.0 MB) There is no eth0. Is that normal? In the "Network Connections" GUI there is an entry "Wired connection 1", its "MAC address" field is blank. How can I make the wired connection work?

  Read the article

• D-Link wireless router losing outbound data

  - by gsteinert

  I have a Linux box running the Apache web server behind a D-Link wireless router (nothing fancy, just standard kit that comes with Virgin Media broadband). My issue is that when requesting web pages (from within the network or via the web), the back end of the page seems to be being dropped. For example, I tried to display a text-only file, and all I could get was the first 40-70% of the file (it changed slightly with each refresh). The apache access logs show that only part of the data was being sent (~6000 bytes instead of the 12000+ bytes of the file). Removing my router from the equation fixes the issue and I can download any files no matter the size with no problems. My theory is that the uploaded packets are either being dropped or held up by the config of the router. Is there anything I can do to alleviate the problem? (Perhaps a way of reconfiguring the router to upload packets harder/better/faster/stronger or an option in apache that provides a workaround) As a last resort I will get a second NIC for my Linux box and turn it into a router, but that would mean the box will be on 24/7... not the most ideal of circumstances. Gary

  Read the article

• Multiple Screen - Keyboard Sharing

  - by nhbdesign

  I run a small architectural firm with several drafters employed, I'm currently setting up a new office space and one of the things on top of my list is a figuring out a way to keep tabs on my drafters work and being able to collaborate in real time. Here's the challenge, they sit in a separate large cubicle room and I'm on the other end of the hallway, the way it is now; every time they’ve got some question on how to proceed on a certain design, they would come all the way to my office, I'd open their file (in read only) give some ideas, save-as new file, they go back copy paste... in short, nonsense. What I've been thinking of is to setup a hardwired solution that should enable me to have an extra monitor on my desktop which is hardwired (through KVM or something) to each of my employees workstations serving as a secondary display, so that I can watch live what they do, interact with them just as if they would have an extra keyboard and monitor in my office, except; I don’t want to have on my desk a separate monitor for each employee.. so I'd want them to be tiled on a single large screen, watching all screens alive, and whenever they ask me (or I just decide..) to step in, I just click on any tile and hurray, I'm in, editing and saving in real time on their workstation. I also want to reserve the option when I want to, to just use that monitor as just an extra screen for my workstation. Is something like that possible in 2013? P.S. I know of TeamViewer and similar internet/software based stuff, but I'm specifically looking for something solid hardwired and maintenance free, and also something that would allow to watch without my employees getting notified every time I do so (I’m not a tough boss though...).

  Read the article

• How to: Simulating keystroke inputs in shell to an app running in an embedded target

  - by fzkl

  I am writing an automation script that runs on an embedded linux target. A part of the script involves running an app on the target and obtaining some data from the stdout. Stdout here is the ssh terminal connection I have to the target. However, this data is available on the stdout only if certain keys are pressed and the key press has to be done on the keyboard connected to the embedded target and not on the host system from which I have ssh'd into the target. Is there any way to simulate this? Edit: Elaborating on what I need - I have an OpenGL app that I run on the embedded linux (works like regular linux) target. This displays some graphics on the embedded system's display device. Pressing f on the keyboard connected to the target outputs the fps data onto the ssh terminal from which I control the target. Since I am automating the process of running this OpenGL app and obtaining the fps scores, I can't expect a keyboard to be connected to the target let alone expect a user to input a keystroke on the embedded target keyboard. How do I go about this? Thanks.

  Read the article

• assign characters to key combinations in XP or Visual Studio .Net

  - by cpj

  I'm running Mac OSX on a MacBookPro (UK keyboard). I run windows XP under parallels in a VM. I run Visual Studio .Net 2003 and 2008 in XP in the VM when i need to. I have English United Kingdom and English United states keyboards setup in XP. (they switch sometimes for no apparent reason) There is no hash "#" key on my mac's keyboard. However, in OSX I can get a hash with an alt+3 key combination. But In Windows XP... I can not make a "#" character. I can go to the character map in windows and copy a hash.. switch into OSX and copy a hash.. search in code and copy a hash.. but I can not make a hash in XP using my keyboard without typing U+0023: ... which you can imagine is annoying. coding anything with hash symbols is becoming a choir. Anyone got any advice or key mapping tricks I can use to get hash characters working in XP using my mac UK keyboard?

  Read the article

• OSX esc key stops working (randomly)

  - by Jan Hancic

  I have a 2011 macbook Air with OS X Mountain Lion (I've upgraded from Lion). And ever since upgrading my escape key randomly stops working. And it's not that the keyboard on the laptop would be damaged as the same happens if I use apple's bluetooth keyboard. So I'm guessing it's a software issue. Also in some cases pressing ctrl+esc achieves the same thing as just esc so I'm 100% it's not a hardware problem. Does anybody have any idea what this might be all about and how to fix it? edit: the escape key stops working completely but it starts working again after I restart the computer. edit2: this usually happens after the computer wakes from sleep. So it's not like that is just stopps working in the middle of using it, but rather after I put it to sleep (or just close the lid) and then open it again. Has nobody got the same issue? Is there a better place to ask OSX related questions than SuperUser maybe?

  Read the article

• Can't connect to LAN when connected to D-Link DIR-615

  - by Senseful

  I'm have a D-Link DIR-615 Wireless N 300 Router. I didn't use the CD it comes with to set up the network. Instead I configured it manually through the router's settings that are accessed via a web browser. The main changes I made are: Secured the router so that a password is required before clients can use the wireless internet. Broadcasting 802.11N only (not B or G). I can connect to the router just fine and I'm able to access the internet. The only problem is that I don't see any of the other computers in my LAN. When I try connecting to another Wi-Fi router that I have (which is connected to the same network), I can see all of the computer's on my LAN just fine. Therefore, I'm guessing that the reason I can't connect to the LAN is not a problem with my computer and is a problem with the router instead. I'm on a MacBook Air running Mac OS X 10.6.6. I tried contacting D-Link technical support, but they only try to help you if you have problems connecting to the internet. They aren't really concerned with problems that have to do with the accessing PC's on the same network.

  Read the article

• How to configure a Router (TL-WR1043ND) to work in WDS mode?

  - by LanceBaynes

  I have a WRT160NL router (192.168.1.0/24 - OpenWrt 10.04) as AP. It's: - WAN port: connected to the ISP - WLAN: working as an AP, using 64 bit WEP/SSID: "MYWORKINGSSID", channel 5, using password: "MYPASSWORDHERE" - It's IP Address is: 192.168.1.1 Ok! It's working great! But: I have a TL-WR1043ND router that I want to configure as a "WDS". (My purpose is to extend the wireless range of the original WRT160NL.) Here is how I configure the TL-WR1043ND: 1) I enable WDS bridging. 2) In the "Survey" I select my already working network. 3) I set up the encryption (exact same like the already working one) 4) I choose channel 5 5) I type the SSID 6) I disable the DHCP server on it. After I reboot the router and connect to this router (TL-WR1043ND) over wireless I'm trying to ping google.com. From the ping I see that I can reach this router, that's ok, but it seems like that this router can't connect to the original one, the WRT160NL (so I don't get ping reply from Google). The encryption settings/password is good I checked it many-many-many times. what could be the problem? I'm thinking it could be a routing problem, but what should I add to the "Static Routing" menu? I tried to change the IP address of the TL-WR1043ND to: 192.168.1.2 So if this a routing issue then I should add a static routing rule that says: If destination: any then forward the packet to 192.168.1.1 p.s.: I updated the Firmware to the latest version. It's still the same. p.s.2: The HW version of the TL-WR1043ND is 1.8 p.s.3: Could that be the problem that I use different routers? (If I would buy.. another TL-WR1043ND and use it instead of the WRT160NL, and with normal Firmware, not OpenWrt, then it would work?? The "WDS" is different on different routers?) p.s.4: I will try to check the router logs@night - and paste it here! :\

  Read the article

• How to bypass firewall to connect to a proxy server?

  - by Bruce

  I am conducting a small experiment on my office network. I have setup a proxy server on my desktop machine (connected to my LAN) and I have volunteers access the internet via my proxy server. Everything is working well. The problem is people cannot connect to the proxy server through their laptops. I asked my network admin and he said the wireless network has a firewall which prevents users from connecting to my proxy. He said I could tunnel the traffic or use SSH though. I am afraid I do not understand fully what is going on. Is there a way by which users connected on the wireless network can connect to my desktop? I am using FreeProxy on Windows as my proxy server: http://www.handcraftedsoftware.org/index.php?page=download FreeProxy allows me to create a SOCKS 4/4a/5 proxy. Is that what I need? Part of the experiment involves logging the URL requests of the users. I am doing a measurement study. So, any solution must allow me to log the URL requests of users. Also, what changes do I need to make in the browser configuration.

  Read the article

• How can I restore my original IME Romaji input settings?

  - by JOhn K

  the this one, Japanese IME on Windows: switch back to romaji input method (3) did not help. The problem seems the same. My Vista home premium version PC, I had been using Microsoft IME to use English and Japanese input using romaji henkan for a long time. One day, all of a sudden, first when I started up the PC, it has cap lock indicator ON. So, I press SHIFT key, CAP lock indicator is off!(This I have to do every morning.) Now when I want to type romaji input to change to Japanese, I switch EN English (United States) to "JP Japanese (Japan) and select input to hiragana input. It worked until that day. But now when I set to input romaji for hiragana as I used to do and start typing, then it shows Japanese hiragana directly on the display just as keyboard setting as Japanese ???109???????? as shown in Wikipedia JIS keyboard. And I cannot show hiragana as I wanted ( I can convert to Kanji OK) etc. by hitting space key. But its key board arrangement is what I never learned. Other thing I found is when I hit "`" key, it switches between hiragana and alphabet. When I see Control panel setting it is the same setting as I have seen. Please suggest me a solution to get the original setting for IME input mode as I used to do. John K.

  Read the article

< Previous Page | 117 118 119 120 121 122 123 124 125 126 127 128  | Next Page >