Search Results

Search found 6612 results on 265 pages for 'seconds'.

Page 122/265 | < Previous Page | 118 119 120 121 122 123 124 125 126 127 128 129  | Next Page >

• Why is my NTP controlled computer clock two minutes ahead?

  - by Martin Liversage

  The clock in my computer is configured to be synchronized using NTP. To verify this I have tried two NTP clients using various NTP servers. My computer and the NTP clients are in complete agreement about the current time even across a wide range of NTP servers. I also have a GPS and my national phone company provides an accurate clock available by calling a specific phone number. Both my GPS and the phone company agrees on the current time. However, my computer is almost precisely two minutes (or 1 minute and 59 seconds) ahead of what I believe to be the "real" current time where I live. Why is my computer two minutes ahead? I realize that synchronizing clocks using the internet may not be entirely accurate as there is latency, but two minutes is a very long time on the internet. Is NTP really two minutes ahead? I'm running Windows 7 and live in the time zone UTC+1, but I don't think that is important in understanding my problem.

  Read the article

• strange behaviour - dhclient needs to be run twice in order to connect to wireless

  - by splicer

  I am trying to connect my to my wlan without the use of NetworkManager. I run the following commands after boot: iwconfig wlan0 enc <WEP passwd> mode managed essid <name> channel 6 ifconfig wlan0 up dhclient wlan0 At this point, dhclient stalls for ages (perhaps 2 minutes), then it returns with PING 192.168.1.254 (192.168.1.254) from 192.168.1.65 wlan0: 56(84) bytes of data. --- 192.168.1.254 ping statistics --- 3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 3000ms pipe 3 .. The strange thing is that when I run pkill dhclient; dhclient wlan0 right after this, it connects in about <3 seconds. Any idea what could be the cause of this problem? Edit: oh, and I did try using the -timeout flag on dhclient but that didn't seem to make any difference (it still stalled for ages).

  Read the article

• How to statically configure DNS servers on a Cisco router when the WAN interface uses DHCP?

  - by Massimo

  I have a Cisco router (model 887VA, IOS 15.4) used to connect a LAN to the Internet via ADSL. The WAN interface uses DHCP: interface ATM0.1 point-to-point ip address dhcp I need the router to use a statically-defined DNS server for name resolution: ip name-server A.B.C.D However, the router insists on using the DNS servers supplied by the ISP via DHCP: Router#ping www.google.com Translating "www.google.com"...domain server (<ISP DNS>) [OK] Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 173.194.116.208, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 44/45/48 ms How can I tell the router to ignore the ISP-supplied DNS servers and only use the statically-configured one?

  Read the article

• Audio services in windows 7

  - by infant programmer 'Aravind'

  In an attempt of blocking a viral service on my system (which was restarting my system automatically for every 30 seconds), I disabled all the services, and later enabled trustworthy services only. (note: Hide all microsoft services didn't work blocking the auto restart so I disabled all services) Now I have been succeeded in blocking automatic restart and I am able to access internet and all other necessary stuffs. Well, however system audio is mute(definitely because a necessary service is not running). Now I need a list of services that need to be started (set automatic) on windows 7.

  Read the article

• bad ram or bad motherboard

  - by user39508

  I have a computer which crashes after about 5-45 seconds of operation. It can run memtest86+, and it doesn't display any errors, but it doesn't prevent it from crashing within the time frame listed above. The heat sink appears to be installed correctly, and I don't think it is related to overheating. The motherboard is connected to the ram and a monitor, nothing else is installed. The processor is an atom 330, running memtest86+ 4.0. Any insight into if the ram is bad or if it is the motherboard/psu/cpu? Thanks!

  Read the article

• Compaq nc4200 screen cutting out and keyboard lagging after dropping - could I repair this?

  - by Holly Gray

  I have a HP Compaq nc4200 laptop. I got it from a family member who no longer needed it, who got it from a sale of old office equipment, so it's at the very least third-hand, and somewhat battered. Today, I dropped it. It seemed unharmed at first, but the screen cuts out every few minutes (sometimes seconds), then fades back. Keyboard input also occasionally starts lagging, as does the mouse. It might be a coincidence, but, oddly, it seems as if, when the screen cuts out, it comes back sooner if I use the trackpad. Is this something that I could fix? What might be causing it?

  Read the article

• Kubuntu Monitor Out of Range

  - by uncleo

  My X server seems to be faulty, but I don't know why. I had some problems last week with a new motherboard, but they seemed to be resolved. Today, I updated Kubuntu and restarted, but my Viewsonic VX900 LCD monitor shows the splash screen for several seconds, then displays the message "Out of Range" I have tried various kernels in Grub, some in recovery mode, most do the same thing. No key combinations bring up a shell prompt like I expect. The one exception was a very old kernel, that would only mount the file system as read-only, so I can't fix up the xorg.conf file. Is there anything to be done?

  Read the article

• Recursively resize images from one directory tree to another?

  - by davr

  I have a large complex directory tree full of JPG images. I would like to create a second directory tree that exactly mirrors the first, but resizing all the images down to a set size (say 2000x1500 or something) and quality (perhaps 85%). Is there any tool that would allow me to easily do this on Windows? I could write some scripts to automate it with bash and image magick, but first want to see if it's already been done. Faster is better too, as I have thousands of images. So something like Photoshop is probably not a good solution as it might take a couple of seconds per image.

  Read the article

• Secondary Monitor won't Display at Full Resolution with Primary Display Disconnected

  - by Laramie

  I have had a bad day. Among today's events, the LCD display on my Dell E6500 notebook failed. It had been working with a secondary monitor connected through a VGA cable at 1600x900 resolution until I removed the LCD from my notebook for repair. Now the max resolution available on the secondary display is 1024x768. If I reconnect the burned out primary display, the secondary monitor is again available at 1600x900. The video card is an onboard Mobil Intel 4. How can I maintain the secondary display at 1600x900 with the primary display disconnected (for repair)? Edit: I just noticed that when Windows boots, it displays at the correct resolution and I can see my desktop in all its glory for a couple seconds then reverts to 1024x768.

  Read the article

• What is Mobsync.exe? Assuming I don't need it, can I disable it in Windows 7 without ill side effect

  - by Chris W. Rea

  I'm running Windows 7. Occasionally when I resume my computer from standby, it seems to wait 20-30 seconds or so before giving me full control back. In an attempt to diagnose why, I've been watching what's going on using the awesome Process Explorer. One of the processes I've noticed being started during that hiccup time is Mobsync.exe, described as "Microsoft Sync Center". Sync? Sync what? So, what is Mobsync.exe used for, exactly? Assuming I don't need its functionality, can I disable it in Windows 7 without ill side effect? If so, what's the best way to disable Mobsync.exe?

  Read the article

• WiFi: Connect to a network with hidden SSID in Windows 7

  - by Dor

  I have Windows 7 with the following station: D-Link DWA-160 Xtreme N Dual Band USB Adapter(rev.A2) (driver version 3.5.0.21). I'm trying to connect to a wireless network that has an hidden SSID with the command: Netsh wlan connect name="myNetworkProfile" The profile is configured to connect even if the network is not broadcasting its name (SSID). Despite that, the command fails promptly every time with the message: The network specified by profile "myNetworkProfile" is not available to connect. Nonetheless, when trying to connect manually using the dialog box (see image below), it successfully connects to the network after about 10 or 15 seconds. Also, Please - no need to elaborate about how useless the hidden SSID feature is.

  Read the article

• Disable Offline Files (mobsync.exe) on Windows 7 Home

  - by Synetech

  This morning I was watching the CPU graph of a Windows 7 Home laptop and noticed that every few seconds, the CPU would spike several percent. I watched the processes and determined that it was mobsync.exe (Offline Files) that was the culprit. I tried the usual steps that Googling turns up, and clicking the Manage Offline Files link to bring up the Offline Files dialog to click Disable Synch does not work because the dialog will not display. This makes sense since everything I have read indicates that Offline Files is not even included/supported in the Home version, so I am at a loss as to why it is running at all, let alone why it is sucking up CPU cycles. (My best guess is that it was started when they pressed Win+X to access the Mobility Center.) Of course I can just kill mobsync, but it could always just come back. How/why would mobsync be running on a Home version and how can it be disabled (of course the Group Policy editor is not available on a Home version).

  Read the article

• Hybrid drive not booting faster than a normal HD

  - by Nigel Trotter

  I have used Windows 7 to create an image of my existing standard 160GB HD and copied this image back to a bigger 500GB Seagate hybrid drive. After copying the image to the hybrid I had to resize the partition, which was fine but after rebooting a few times to "teach" the hybrid, I have no increase in boot speed. It still takes 20-25 seconds to close down and then over a minute to start up. Is this something to do with the way the image lays itself on the drive indiscriminately? Do I need to load the OS on the drive from scratch to get the benefits? My PC with an i5 processor, is using AHCI mode.

  Read the article

• How do I diagnose a HP Notebook which has hardware issues?

  - by Rob

  My HP DV6t-2300 recently crashed while using FLV Player. It wouldn't start up after this so I had to do a hardware reset (remove power sources, hold down power button ~15 seconds, put back power sources). After this it would turn on, but start up would freeze in Ubuntu, Windows 7, Ubuntu Recovery Mode, and various Linux Live CDs. The only successful way to boot was in Windows 7 Safe Mode. The HP Customer Service was very polite, but they are trying to blame it on a corrupt operating system which is clearly not the case (since I have tried 4 operating systems and none work). I am thinking it might be the GPU since 1) I was watching movies when it crashed and 2) Windows Safe Mode might not use the dedicated GPU. I already ran Memory and HDD tests and there were no detected errors. Any ideas of what's wrong, or suggestions for tests that I should run in safe mode? Should I try reinstalling Windows 7 to convince HP that it's not the OS?

  Read the article

• Postfix throttling for outgoing messages

  - by Sergey Kovalev

  I need Postfix to send outgoing messages (from local PHP) with a certain rate. Say, one message in 120 seconds. Any messages exceeding this rate should be queued (delayed) and delivered later. Policyd is not what I'm looking for. I don't need limiting overall number of messages sent. I need a pause (120s) between any two messages beeing sent. Tried this config, but it's not working: initial_destination_concurrency = 1 default_destination_concurrency_limit = 1 default_destination_rate_delay = 120 default_destination_recipient_limit = 1 default_process_limit = 1 Any suggestions?

  Read the article

• Mac OS X: Trying to install prolog using fink

  - by sixtyfootersdude

  I am trying to install prolog on Mac OS X 10.4.11. I just downloaded fink because I think that that should help me and I am trying to get either: Package swi-prolog-5.8.1-2 or Package gprolog-1.3.1-1 But I am not having any luck. Here is what I was doing: % fink install swi-prolog-5.8.1-2 Information about 1723 packages read in 0 seconds. Failed: no package found for specification 'swi-prolog-5.8.1-2'! % Question 1: Are these what I want to download? Question 2: Why isn't fink working?

  Read the article

• linux/shell: change a file's modify timestamp relatively?

  - by index

  My Canon camera produces files like IMG_1234.JPG and MVI_1234.AVI. It also timestamps those files. Unfortunately during a trip to another timezone several cameras were used, one of which did not have the correct time zone set - meta data mess.. Now I would like to correct this. Proposed algorithm: 1 read file's modify date 2 add delta, i.e. hhmmss (preferred: change timezone) 3 write new timestamp Unless someone knows a tool or a combination of tools that do the trick directly, maybe one could simplify the calculation using epoch time (seconds since ..) and whip up a shell script. Any help appreciated!

  Read the article

• sox mix nested scripts on amazon ec2 rhel linux

  - by Ray

  I'm trying to use "sox" to mix some audio files. The command works great on my Mac terminal sox -m audio.wav "| sox upload.wav -p trim 2 1 pad 6" final.wav This mixes (not concatenate) audio.wav and a section of upload.wav from the 2nd second to the 3rd second and adds 6 seconds of padding in the front, and outputs to final.wav Now the problem is, the SAME EXACT command does NOT work my Amazon EC2 RHEL box. (sox is installed correctly). I get the following error sox soxio: Can't open input file `| sox upload.wav -p trim 2 2 pad 6': No such file or directory For some reason RedHat doesn't like the double quotes. Even though it is documented to be used this way. Thanks for your help!

  Read the article

• Restoring permissions on Windows 2008

  - by Andrey

  I have played with folder permissions due to SVN not being able to write to a folder and now I got into a state where I go to any folder of C: drive in Windows Explorer and when I right-click it takes 30 seconds to show the context menu and it just hangs the window after that. It definitely has something to do with permissions as it was all working fine until I started tweaking permissions about an hour ago. My login belongs to two groups Users and Administrators. I changed ownership of C drive to Administrators group and I think it screwed everything, but I can't change it back because I don't even remember what it was :) Oh, and only Administrators group has access to drive C now. Any way to reset permissions to some previous state or some workable state?

  Read the article

• Laptop charger disconnects and reconnects, charger or battery broken?

  - by Rob

  I've got an Acer Aspire One netbook (AOA-150) and there's obviously something wrong with it. The charging port gets VERY HOT and the charger seems to disconnect and reconnect quickly sometimes. This only happens when the netbook is running, and it doesn't seem to care what it's doing other than being on. The battery has an extremely short life (< 30minutes, sometimes) and I almost exclusively run it on the power cable (which needs the battery plugged in. Having it just plugged into the wall won't start up). Does this sound like a problem with the power cable or the battery? The plug for the cable and the port get so hot that if I held them for longer than a few seconds, I'm sure I'd get burnt. EDIT Just got "Popular Question" on this and it WAS the power jack. The ground on it came loose from the board. A bit of solder on it and everything is working great again.

  Read the article

• OLTP Sql Server RAID configuration with 10 disks, allocation Unit and disk stripe size

  - by Chris Wood

  On a new db server I only have 10 disks to play with, The usage is about a booking every 3-5 seconds, so not high volume, I know compromises have to be made, but my initial thoughts are - DISK 1 & 2 - RAID 1 - OS DISKS 3,4,5,6 - RAID 10 - Data, Indexes & TempDB DISKS 7,8,9,10 - RAID 10 - Logs & Backup Full backups will take place when there is virtually no traffic on the website so not bothered about the contention with the logs. disk 3-10 - 8kb NTFS unit allocation size disk 3-10 - 64kb Disk Stripe size does this seems to be sensible, any other considerations I have omitted ? thanks

  Read the article

• Jan 2010 Microsoft update trashed my Win XP (64bit) PC

  - by Mark Pawelek

  I waited until this morning to install these 5 updates. My ancient Win XP (32 bit) PC has no problems but my Win XP 64 bit will not start. From the startup menu none of the 5 options given (e.g. safe mode, last known good configuration, etc) work. After selecting an option, the Windows Logo screen appears. About 9 seconds later a blue screen of death flashes [I can't read the error messages because it's there for about 100 ms] then it cycles through the reboot again. PS: This is a pretty cheap mobo (Ge Force) with an AMD 3 GH chip - but until today it did actually work. What should I do? Reinstall the O/S?

  Read the article

• Juniper J4350 out of order

  - by Benjamin Baron

  I have got two (2) Juniper routers J4350 that are out of order : All the interfaces are down (leds on the interfaces don't ligthen, ping dosen't respond) No output on the console port (even when booting) I've tried to reset the router (holding the RESET CONFIG button on the front panel during 15 seconds) and nothing happened, even while booting the device I've opened the router to check the fans. I've removed some dust and nothing has changed. I wanted to precise that the leds on the front panel are all on: The POWER led is green The STATUS led is red The ALARM led is on and is orange The HA (High Availablity) is on and orange as well I have found nothing on the Internet to solve this problem... Thank you for helping me :)

  Read the article

• Ubuntu 9.10 Karmic, nVidea Quadro NVS 280 PCi, Eizo S1921 Dual Screen (Twin View) Slow Window Draws

  - by Spasm

  I have been following this Tutorial to get dual monitors working on my box http://www.dwasifar.com/?p=862&cpage=1#comment-5727 It works! However, when ever I move a window, the redraw of that window takes 3-8 seconds. Even moving the window takes the same amount of time Is this being done in software rather than the nVidea hardware? The windows themselves do not respond. I have seen a few old threads but no relevant fixes - If anyone could suggest a fix I would very much appreciate it. Thanks in advance

  Read the article

• How long do managed gigabit ethernet switches take to boot up?

  - by Warren P

  One critical drawback that I have found in researching managed-switches, and one that I have some past experience with is that anything with "lots" of firmware is going to have lots of issues associated with that firmware. We are in the middle of researching rackmount gigabit switches (48 port). It looks like for 48 ports, our only choice is managed switches (Dell, Cisco/Linksys,HP, etc). What I want to know, that I can not find out much about is the boot-time for various managed switches. If you own one, can you please answer with the model number, and the cold boot time in seconds. I have read online that Linksys (now Cisco) SRW series sometimes take almost 5 minutes before they are fully booted up, and that is an unacceptable cost for us. I particularly want to know about Dell PowerConnect managed switch bootup time (model 3548 and 5448), and would like to confirm the 5-minute boot time on the SRW2048 or similar model, and any HP ProCurve boot up times. The composite of all those figures ought to form an interesting overall performance picture.

  Read the article

< Previous Page | 118 119 120 121 122 123 124 125 126 127 128 129  | Next Page >