Search Results

Search found 3192 results on 128 pages for 'dell precision'.

Page 13/128 | < Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >

• I need help choosing between two configurations of the Dell Studio 14

  - by Adnan

  There are two configurations of the Dell Studio 14 (1458) which I'm looking at: Config 1: Core i7-720QM @ 1.6 GHz; ATI Mobility Radeon HD 5450 1GB; 4gb DDR3 RAM @ 1066 MHz; 500 GB SATA HDD @ 7200 RPM; Price: $999 Config 2: Core i5-430M; ATI Mobility Radeon HD 4530 512MB; 4GB DDR3 RAM @ 1066 MHz; 500 GV SATA HDD @ 7200 RPM; Price: $874 What I want to know is, would config 1 still be able to do decent gaming (maybe some Starcraft II), and is there a great performance difference between the i5 and i7 processors? Is the $130 extra worth it for the i7 and better graphics card? I do more than just basic computing. I plan on getting into web design (specifically using Photoshop and Dreamweaver), and I wish to do gaming. I know Conifg 1 is the better value, but I want to be sure that the $130 more is truly worth it. I dont have too much money and want to spend wisely as possible, yet I am a computer geek and plan on doing a lot more than the average user.

  Read the article

• Precision error adding doubles

  - by wrongusername

  When I try to do term[number].coefficient += co; with both term[number].coefficient and co doubles, adding -8.2 to +1 gives me -7.300000000000001. How can I make it equal to 7.3?

  Read the article

• Dell R320 RAID 10 with CacheCade

  - by Geekman

  I'm looking for a higher-performance build for our 1RU Dell R320 servers, in terms of IOPS. Right now I'm fairly settled on: 4 x 600 GB 3.5" 15K RPM SAS RAID 1+0 array This should give good performance, but if possible, I want to also add an SSD Cache into the mix, but I'm not sure if there's enough room? According to the tech-specs, there's only up to 4 total 3.5" drive bays available. Is there any way to fit at least a single SSD drive along-side the 4x3.5" drives? I was hoping there's a special spot to put the cache SSD drive (though from memory, I doubt there'd be room). Or am I right in thinking that the cache drives are simply drives plugged in "normally" just as any other drive, but are nominated as CacheCade drives in the PERC controller? Are there any options for having the 4x600GB RAID 10 array, and the SSD cache drive, too? Based on the tech-specs (with up to 8x2.5" drives), maybe I need to use 2.5" SAS drives, leaving another 4 bays spare, plenty of room for the SSD cache drive. Has anyone achieved this using 3.5" drives, somehow?

  Read the article

• PC won't PXE boot to WDS/MDT with Dell Optiplex 755

  - by Moman10

  I am trying to set up a basic MDT solution. I have set one up in the past at a previous job and it worked flawlessly, however here I'm running into a problem and am having no luck getting around it. I've installed Windows Server 2012 and MDT 2013, along with adding on the WDS role. I haven't configured much outside of the defaults for WDS, basically just set PXE response to respond to all clients (and unchecked admin approval). This machine does not run a DHCP server. I looked on the DHCP scope of our DHCP server, it shows options 66/67 checked and the server name of the WDS server is in there as well. I didn't add this but I assume it was put on during the install process (I believe I had to manually make some adjustments at my old job for this). The PC I have is a Dell Optiplex 755. I have enabled the onbard NIC w/PXE boot option in BIOS and attempted to boot. I get a "TFTP...." error but nothing offering out a DHCP address like I'm used to. In my previous job it pretty much worked right out of the box. I've verified that PortFast is enabled on the port and I've tried a couple different PCs (but both are the same model, only model I have to work with). No matter what, I get the same error. The subnet the PC is in is a different subnet than where the WDS server is sitting, but there are IP helper statements on the switch and the PCs can get regular DHCP addresses just fine from the DHCP server, just doesn't seem to get offered out a PXE boot option. I don't know if the problem is a configuration with the server or the PC itself...but after a few days of Googling I'm running out of ideas. Does anyone have a good idea of something it may be?

  Read the article

• VMWare Setup with 2 Servers and a DAS (DELL MD3220)

  - by Kumala

  I am planning to use a VMWare based setup consisting of two VMWare servers (2 CPU, 256GB Memory) and a DAS (DELL MD3220 with 24x900GB disks). The virtual machines will be half running MS SQL databases (Application, Sharepoint, BI) and the other half of the VM will be file services, IIS. To enhance the capacity of the storage, we'll be adding a MD1220 enclosure with another 24x900GB to the MD3220. Both DAS will have 2 controllers. Our current measured IOPS is 1000 IOPS average, 7000 IOPS peak (those happen maybe twice per hour). We are in the planning phase now and are looking at the proper setup of the disks. The intention is to setup up both DAS one of the DAS with RAID 10 only and the other DAS with RAID 5. That will allow us to put the applications on the DAS that supports the application performance needs best. Question is how best to partition the two DASs to get best possible IOPS/MBps, each DAS will have to have 2 hot spares? For the RAID 5 Setup: Generally speaking, would it be better to have one single disk group across all 22 disks (24 - 2 hot spares) with both controllers assigned to the one disk group or is it better to have 2 disk groups each 11 disks, assigned to one of the two controllers? Same question for the RAID 10 setup: The plan is: 2 disks for logs (Raid 1), 2 Hotspare and 20 disks for RAID 10. Option 1: 5 * 4 disks (RAID 10), with two groups assigned to 1 controller and 3 groups to the other controller Option 2: One large RAID 10 across all the disks and have both controllers assigned to the same group? I would assume that there is no right or wrong, but it all depends very much on the specific application behaviour, so I am looking for some general ideas what the pros and cons are of the different options. IF there are other meaningful options, feel free to propose them.

  Read the article

• Arbitrary precision arithmetic with Ruby

  - by macek

  How the heck does Ruby do this? Does Jörg or anyone else know what's happening behind the scenes? irb(main):001:0> 999**999 368063488259223267894700840060521865838338232037353204655959621437025609300472231530103873614505175218691345257589896391130393189447969771645832382192366076536631132001776175977932178658703660778465765811830827876982014124022948671975678131724958064427949902810498973271030787716781467419524180040734398996952930832508934116945966120176735120823151959779536852290090377452502236990839453416790640456116471139751546750048602189291028640970574762600185950226138244530187489211615864021135312077912018844630780307462205252807737757672094320692373101032517459518497524015120165166724189816766397247824175394802028228160027100623998873667435799073054618906855460488351426611310634023489044291860510352301912426608488807462312126590206830413782664554260411266378866626653755763627796569082931785645600816236891168141774993267488171702172191072731069216881668294625679492696148976999868715671440874206427212056717373099639711168901197440416590226524192782842896415414611688187391232048327738965820265934093108172054875188246591760877131657895633586576611857277011782497943522945011248430439201297015119468730712364007639373910811953430309476832453230123996750235710787086641070310288725389595138936784715274150426495416196669832679980253436807864187160054589045664027158817958549374490512399055448819148487049363674611664609890030088549591992466360050042566270348330911795487647045949301286614658650071299695652245266080672989921799342509291635330827874264789587306974472327718704306352445925996155619153783913237212716010410294999877569745287353422903443387562746452522860420416689019732913798073773281533570910205207767157128174184873357050830752777900041943256738499067821488421053870869022738698816059810579221002560882999884763252161747566893835178558961142349304466506402373556318707175710866983035313122068321102457824112014969387225476259342872866363550383840720010832906695360553556647545295849966279980830561242960013654529514995113584909050813015198928283202189194615501403435553060147713139766323195743324848047347575473228198492343231496580885057330510949058490527738662697480293583612233134502078182014347192522391449087738579081585795613547198599661273567662441490401862839817822686573112998663038868314974259766039340894024308383451039874674061160538242392803580758232755749310843694194787991556647907091849600704712003371103926967137408125713631396699343733288014254084819379380555174777020843568689927348949484201042595271932630685747613835385434424807024615161848223715989797178155169951121052285149157137697718850449708843330475301440373094611119631361702936342263219382793996895988331701890693689862459020775599439506870005130750427949747071390095256759203426671803377068109744629909769176319526837824364926844730545524646494321826241925107158040561607706364484910978348669388142016838792902926158979355432483611517588605967745393958061959024834251565197963477521095821435651996730128376734574843289089682710350244222290017891280419782767803785277960834729869249991658417000499998999

  Read the article

• Dell laptop keyboard doesn't work

  - by Tam

  I'm trying to fix my in-laws laptop, it's a Dell Studio 1745 that's running Windows 7 64 bit. The problem is that most of the keys on the keyboard do not work. The function keys work and the caps lock and numpad keys work, but no other keys do. If I hit the F2 key enough times when starting up, I can get to the BIOS, but after that even the function keys stop working. If I let it go all the way to the Windows login screen, I can see that the caps lock and num lock work - little images on screen actually appear, but they don't toggle the state of the key, i.e.,capslock is always off, numlock is always off. Using the fn+function combo works, so changing the brightness, etc. works fine. I'm stumped. I've tried disconnecting power and battery and leaving it for an hour or so before starting up but that hasn't helped either. Also - this might be a red herring - the touchpad is failing as well, the MS Device Manager says that it's failing with status 10, "unable to start device"

  Read the article

• Driver corruption when deploying Dell Touchpad Drivers (with software) during imaging process

  - by BigHomie

  We're an sccm shop, and use it to deploy Windows. When deploying Dell laptops (multiple models), the touchpad drivers seem install properly, but the software doesn't. The resulting problem is that when the touchpad is pressed on occasion, the mouse pointer will 'jump' to certain points on the screen. A possible symptom of this problem/visible sign is if the touchpad icon isn't in the system tray. The software is in the control panel, but when opened part of the gui is pixelated, indicating botched install maybe? The manual resolution to this, is to go into device manager and uninstall the driver with the option to uninstall all driver software. After a restart, the driver and software is apparently reinstalled, and from there works as expected. Obviously this partially defeats the purpose of a zero touch deployment. If anyone knows why this is and/or a possible workaround, those answers would be valid as well. Barring that, I want to find a way to deploy the driver and touchpad software in an unattended way, so that it can be conditionally installing during the imaging process. To be honest I'm not sure how to troubleshoot this, I suppose I could try drvinst.exe to install the driver, but finding out why this fails initially would keep me from spinning my wheels.

  Read the article

• Make Dell's OpenManage 6.2 information available through SNMP

  - by tronda

  I have successfully installed OpenManage on a CentOS 5.4 server and I'm able to use OpenManage through the web interface running on port 1311, but I would like to be able to expose this information through the SNMP server. I don't know SNMP particularly well so the configuration is a result of trial and error. I've tried to follow the description pointed out in the Open Manage Server Administrator User Guide. I've followed the documentation regarding SNMP configuration, but without success. I've created a small snmpd.conf file: com2sec notConfigUser default public group notConfigGroup v1 notConfigUser group notConfigGroup v2c notConfigUser view systemview included .1.3.6.1.2.1.1 view systemview included .1.3.6.1.2.1.25.1.1 access notConfigGroup "" any noauth exact all all none view all included .1 rwcommunity public 10.200.26.50 syslocation "Somewhere" syscontact [email protected] pass .1.3.6.1.4.1.4413.4.1 /usr/bin/ucd5820stat smuxpeer .1.3.6.1.4.1.674.10892.1 When I try to fetch SNMP information by using snmpwalk I get the following output: SNMPv2-MIB::sysDescr.0 = STRING: Linux myserver.test.com 2.6.18-164.15.1.el5 #1 SMP Wed Mar 17 11:30:06 EDT 2010 x86_64 SNMPv2-MIB::sysObjectID.0 = OID: NET-SNMP-MIB::netSnmpAgentOIDs.10 DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (1180389) 3:16:43.89 SNMPv2-MIB::sysContact.0 = STRING: [email protected] SNMPv2-MIB::sysName.0 = STRING: myserver.test.com SNMPv2-MIB::sysLocation.0 = STRING: "Somewhere" SNMPv2-MIB::sysORLastChange.0 = Timeticks: (0) 0:00:00.00 SNMPv2-MIB::sysORID.1 = OID: SNMPv2-MIB::snmpMIB SNMPv2-MIB::sysORID.2 = OID: TCP-MIB::tcpMIB SNMPv2-MIB::sysORID.3 = OID: IP-MIB::ip SNMPv2-MIB::sysORID.4 = OID: UDP-MIB::udpMIB SNMPv2-MIB::sysORID.5 = OID: SNMP-VIEW-BASED-ACM-MIB::vacmBasicGroup SNMPv2-MIB::sysORID.6 = OID: SNMP-FRAMEWORK-MIB::snmpFrameworkMIBCompliance SNMPv2-MIB::sysORID.7 = OID: SNMP-MPD-MIB::snmpMPDCompliance SNMPv2-MIB::sysORID.8 = OID: SNMP-USER-BASED-SM-MIB::usmMIBCompliance SNMPv2-MIB::sysORDescr.1 = STRING: The MIB module for SNMPv2 entities SNMPv2-MIB::sysORDescr.2 = STRING: The MIB module for managing TCP implementations SNMPv2-MIB::sysORDescr.3 = STRING: The MIB module for managing IP and ICMP implementations SNMPv2-MIB::sysORDescr.4 = STRING: The MIB module for managing UDP implementations SNMPv2-MIB::sysORDescr.5 = STRING: View-based Access Control Model for SNMP. SNMPv2-MIB::sysORDescr.6 = STRING: The SNMP Management Architecture MIB. SNMPv2-MIB::sysORDescr.7 = STRING: The MIB for Message Processing and Dispatching. SNMPv2-MIB::sysORDescr.8 = STRING: The management information definitions for the SNMP User-based Security Model. SNMPv2-MIB::sysORUpTime.1 = Timeticks: (0) 0:00:00.00 SNMPv2-MIB::sysORUpTime.2 = Timeticks: (0) 0:00:00.00 SNMPv2-MIB::sysORUpTime.3 = Timeticks: (0) 0:00:00.00 SNMPv2-MIB::sysORUpTime.4 = Timeticks: (0) 0:00:00.00 SNMPv2-MIB::sysORUpTime.5 = Timeticks: (0) 0:00:00.00 SNMPv2-MIB::sysORUpTime.6 = Timeticks: (0) 0:00:00.00 SNMPv2-MIB::sysORUpTime.7 = Timeticks: (0) 0:00:00.00 SNMPv2-MIB::sysORUpTime.8 = Timeticks: (0) 0:00:00.00 I suspect that I should get some DELL specific information when I use the snmpwalk utility. Is there a configuration in snmpd.conf file which is wrong, or do I have to configure on the OpenManage side in order to get the hardware information accessible from SNMP?

  Read the article

• DELL DRAC & Ubuntu VPN Connection

  - by Mikunos

  I am trying to connect to a DELL DRAC card without success by Ubuntu VPN Connection Manager. I have these data: Protocol: PPTP SERVER IP PPTP: 1233.123.123.123 DRAC IP: 192.168.10.25 Subnet: 255.255.0.0 User: myuser Pass: mypass where have I to write these parameters? I have configured the PPTP connection using the graphical tool in Ubuntu 11.10 ... but in the /var/log/syslog I get these messages: Apr 15 11:33:15 shinet NetworkManager[1035]: <info> Starting VPN service 'pptp'... Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN service 'pptp' started (org.freedesktop.NetworkManager.pptp), PID 18180 Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN service 'pptp' appeared; activating connections Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN plugin state changed: 3 Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN connection 'Connessione VPN 1' (Connect) reply received. Apr 15 11:33:15 shinet pppd[18182]: Plugin /usr/lib/pppd/2.4.5/nm-pptp-pppd-plugin.so loaded. Apr 15 11:33:15 shinet pppd[18182]: pppd 2.4.5 started by root, uid 0 Apr 15 11:33:15 shinet pppd[18182]: Using interface ppp0 Apr 15 11:33:15 shinet pppd[18182]: Connect: ppp0 <--> /dev/pts/1 Apr 15 11:33:15 shinet NetworkManager[1035]: SCPlugin-Ifupdown: devices added (path: /sys/devices/virtual/net/ppp0, iface: ppp0) Apr 15 11:33:15 shinet NetworkManager[1035]: SCPlugin-Ifupdown: device added (path: /sys/devices/virtual/net/ppp0, iface: ppp0): no ifupdown configuration found. Apr 15 11:33:15 shinet pptp[18185]: nm-pptp-service-18180 log[main:pptp.c:314]: The synchronous pptp option is NOT activated Apr 15 11:33:46 shinet pppd[18182]: LCP: timeout sending Config-Requests Apr 15 11:33:46 shinet pppd[18182]: Connection terminated. Apr 15 11:33:46 shinet avahi-daemon[1081]: Withdrawing workstation service for ppp0. Apr 15 11:33:46 shinet NetworkManager[1035]: SCPlugin-Ifupdown: devices removed (path: /sys/devices/virtual/net/ppp0, iface: ppp0) Apr 15 11:33:46 shinet NetworkManager[1035]: <warn> VPN plugin failed: 1 Apr 15 11:33:46 shinet pppd[18182]: Modem hangup Apr 15 11:33:46 shinet NetworkManager[1035]: <warn> VPN plugin failed: 1 Apr 15 11:33:51 shinet pppd[18182]: Exit. Apr 15 11:33:51 shinet NetworkManager[1035]: <warn> VPN plugin failed: 1 Apr 15 11:33:51 shinet NetworkManager[1035]: <info> VPN plugin state changed: 6 Apr 15 11:33:51 shinet NetworkManager[1035]: <info> VPN plugin state change reason: 0 Apr 15 11:33:51 shinet NetworkManager[1035]: <warn> error disconnecting VPN: Could not process the request because no VPN connection was active. Apr 15 11:33:51 shinet NetworkManager[1035]: <info> Policy set 'Wired connection 1' (eth0) as default for IPv4 routing and DNS. Apr 15 11:33:57 shinet NetworkManager[1035]: <info> VPN service 'pptp' disappeared Thanks

  Read the article

• NIC Bonding/balance-rr with Dell PowerConnect 5324

  - by Branden Martin

  I'm trying to get NIC bonding to work with balance-rr so that three NIC ports are combined, so that instead of getting 1 Gbps we get 3 Gbps. We are doing this on two servers connected to the same switch. However, we're only getting the speed of one physical link. We are using 1 Dell PowerConnect 5324, SW version 2.0.1.3, Boot version 1.0.2.02, HW version 00.00.02. Both servers are CentOS 5.9 (Final) running OnApp Hypervisor (CloudBoot) Server 1 is using ports g5-g7 in port-channel 1. Server 2 is using ports g9-g11 in port-channel 2. Switch show interface status Port Type Duplex Speed Neg ctrl State Pressure Mode -------- ------------ ------ ----- -------- ---- ----------- -------- ------- g1 1G-Copper -- -- -- -- Down -- -- g2 1G-Copper Full 1000 Enabled Off Up Disabled Off g3 1G-Copper -- -- -- -- Down -- -- g4 1G-Copper -- -- -- -- Down -- -- g5 1G-Copper Full 1000 Enabled Off Up Disabled Off g6 1G-Copper Full 1000 Enabled Off Up Disabled Off g7 1G-Copper Full 1000 Enabled Off Up Disabled On g8 1G-Copper Full 1000 Enabled Off Up Disabled Off g9 1G-Copper Full 1000 Enabled Off Up Disabled On g10 1G-Copper Full 1000 Enabled Off Up Disabled On g11 1G-Copper Full 1000 Enabled Off Up Disabled Off g12 1G-Copper Full 1000 Enabled Off Up Disabled On g13 1G-Copper -- -- -- -- Down -- -- g14 1G-Copper -- -- -- -- Down -- -- g15 1G-Copper -- -- -- -- Down -- -- g16 1G-Copper -- -- -- -- Down -- -- g17 1G-Copper -- -- -- -- Down -- -- g18 1G-Copper -- -- -- -- Down -- -- g19 1G-Copper -- -- -- -- Down -- -- g20 1G-Copper -- -- -- -- Down -- -- g21 1G-Combo-C -- -- -- -- Down -- -- g22 1G-Combo-C -- -- -- -- Down -- -- g23 1G-Combo-C -- -- -- -- Down -- -- g24 1G-Combo-C Full 100 Enabled Off Up Disabled On Flow Link Ch Type Duplex Speed Neg control State -------- ------- ------ ----- -------- ------- ----------- ch1 1G Full 1000 Enabled Off Up ch2 1G Full 1000 Enabled Off Up ch3 -- -- -- -- -- Not Present ch4 -- -- -- -- -- Not Present ch5 -- -- -- -- -- Not Present ch6 -- -- -- -- -- Not Present ch7 -- -- -- -- -- Not Present ch8 -- -- -- -- -- Not Present Server 1: cat /etc/sysconfig/network-scripts/ifcfg-eth3 DEVICE=eth3 HWADDR=00:1b:21:ac:d5:55 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth4 DEVICE=eth4 HWADDR=68:05:ca:18:28:ae USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth5 DEVICE=eth5 HWADDR=68:05:ca:18:28:af USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-onappstorebond DEVICE=onappstorebond IPADDR=10.200.52.1 NETMASK=255.255.0.0 GATEWAY=10.200.2.254 NETWORK=10.200.0.0 USERCTL=no BOOTPROTO=none ONBOOT=yes cat /proc/net/bonding/onappstorebond Ethernet Channel Bonding Driver: v3.4.0-1 (October 7, 2008) Bonding Mode: load balancing (round-robin) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth3 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 00:1b:21:ac:d5:55 Slave Interface: eth4 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:28:ae Slave Interface: eth5 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:28:af Server 2: cat /etc/sysconfig/network-scripts/ifcfg-eth3 DEVICE=eth3 HWADDR=00:1b:21:ac:d5:a7 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth4 DEVICE=eth4 HWADDR=68:05:ca:18:30:30 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth5 DEVICE=eth5 HWADDR=68:05:ca:18:30:31 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-onappstorebond DEVICE=onappstorebond IPADDR=10.200.53.1 NETMASK=255.255.0.0 GATEWAY=10.200.3.254 NETWORK=10.200.0.0 USERCTL=no BOOTPROTO=none ONBOOT=yes cat /proc/net/bonding/onappstorebond Ethernet Channel Bonding Driver: v3.4.0-1 (October 7, 2008) Bonding Mode: load balancing (round-robin) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth3 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 00:1b:21:ac:d5:a7 Slave Interface: eth4 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:30:30 Slave Interface: eth5 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:30:31 Here are the results of iperf. ------------------------------------------------------------ Client connecting to 10.200.52.1, TCP port 5001 TCP window size: 27.7 KByte (default) ------------------------------------------------------------ [ 3] local 10.200.3.254 port 53766 connected with 10.200.52.1 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 950 MBytes 794 Mbits/sec

  Read the article

• Dell Latitude E6430 Docking Station + Dual Monitor + Laptop Screen Tri-Monitor setup

  - by Larry

  I have a company issued laptop and docking station as well as two monitors The specifications of the hardware are as follows; Laptop: Latitude E6430 BIOS: A02.00 Processor: i7-3720QM CPU @ 2.60 (8 CPUs) Memory: 4096MB RAM Page file: 1825MB used, 4793MB available DirectX 11 Display Driver/Chip: MVIDIA NVS 5200M DAC: Integrated RAMDAC Aprox Total Memory: 2376 (Above 3 details same for both displays) Current Display Mode (Display 1): 1600x900 Current Display Mode (Display 2): 1440x900 the docking station is a Dell Latitude E6420 Docking Station PR03X Port Replicator and I don't think the monitor model is particularly relevant to resolving this issue but they are both Acer V193Ws The story goes like this; the laptop works fine if I VGA one monitor into the laptop through the vga port on the back of the lefthand side of the laptop I can achieve dual monitor display fine (laptop screen + monitor) if I plug the laptop into the docking station and use the vga port in the back of the docking station I can dual monitor fine (laptop screen + monitor) if I plug the laptop into the docking station, the laptop's lefthand side VGA port no longer seems to function at all I've spoken to internal IT about this issue and they're going to get me some kind of VGA splitter or a DVI-VGA adapter to use with the docking station for the second Acer Monitor, but that isn't going to happen for a few days. So I guess what I'm wondering is; is there any way to continue to use the side VGA port on my laptop while using the docking station VGA port? and as a secondary 'followup' pending resolution of the initial issue with getting both monitors up and running (at the moment I have both monitors on my desk but am just using my laptop screen as one of my dual monitor display with one of the monitors [the one connected to dock]), is there any way to CONTINUE to use my laptop monitor to in effect have a triple monitor display (2 monitors + docked laptop)? I am wondering this because internal IT told me that they were aware of some issues with the particular display drivers in my box and triple monitor displays but weren't really going to look TOO much in-depth into that (which is perfectly understandable) since getting the adapter for the dual monitors up and running was the greater priority within their purview. So this is a two parter; Can I dual monitor using two vga cables with 1 docking station vga port and one laptop vga port? is there a setting that can be tweaked somewhere? because plugging the box into the station seems to make the side port stop working and... Is there any reasonably simple and cost-effective work around (e.g. I am find with shelling out maybe a few dollars out of my own pocket for some hardware or software to make my company box tri-display capable) but if this requires some extensive rebuild or new OSs or doing stuff to the BIOS I'd rather have a straight answer about this being untenable as a slight modification to a (once again) company laptop and stop wasting time looking into it Thanks! and please let me know if you guys need any more details (tech specs or something) to answer this question [EDIT] 2/10/2014 Just an update; turned out it really was just a hardware limitation issue. The old laptop just couldn't hack it. Got a new laptop with a better video card and different monitors from my company and am successfully using a triple display currently (2 monitors + laptop screen)

  Read the article

• Disk failing on dell mini, are there diagnostic tools?

  - by John Lawrence Aspden

  Hi, my dell mini 10v running Ubuntu 10.10 runs ok for hours, but then will suddenly slow down drastically. Switching to a console shows lots of error messages, which also get into /var/log/syslog. These errors happen every couple of seconds. I'm figuring that the disk is failing, but is there anyway to be sure, and can laptop disks be replaced easily? Mar 20 11:08:12 dell-mini kernel: [ 2476.378774] ata1.00: status: { DRDY ERR } Mar 20 11:08:12 dell-mini kernel: [ 2476.378785] ata1.00: error: { UNC } Mar 20 11:08:12 dell-mini kernel: [ 2476.449841] ata1.00: configured for UDMA/133 Mar 20 11:08:12 dell-mini kernel: [ 2476.449887] ata1: EH complete Mar 20 11:08:14 dell-mini kernel: [ 2478.777754] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0 Mar 20 11:08:14 dell-mini kernel: [ 2478.777976] ata1.00: BMDMA stat 0x24 Mar 20 11:08:14 dell-mini kernel: [ 2478.778059] ata1.00: failed command: READ DMA Mar 20 11:08:14 dell-mini kernel: [ 2478.778162] ata1.00: cmd c8/00:08:43:3b:97/00:00:00:00:00/e0 tag 0 dma 4096 in Mar 20 11:08:14 dell-mini kernel: [ 2478.778166] res 51/40:00:47:3b:97/00:00:00:00:00/00 Emask 0x9 (media error)

  Read the article

• Precision loss when transforming from cartesian to isometric

  - by Justin Skiles

  My goal is to display a tile map in isometric projection. This tile map has 25 tiles across and 25 tiles down. Each tile is 32x32. See below for how I'm accomplishing this. World Space World Space to Screen Space Rotation (45 degrees) Using a 2D rotation matrix, I use the following: double rotation = Math.PI / 4; double rotatedX = ((tileWorldX * Math.Cos(rotation)) - ((tileWorldY * Math.Sin(rotation))); double rotatedY = ((tileWorldX * Math.Sin(rotation)) + (tileWorldY * Math.Cos(rotation))); World Space to Screen Space Scale (Y-axis reduced by 50%) Here I simply scale down the Y value by a factor of 0.5. Problem And it works, kind of. There are some tiny 1px-2px gaps between some of the tiles when rendering. I think there's some precision loss somewhere, or I'm not understanding how to get these tiles to fit together perfectly. I'm not truncating or converting my values to non-decimal types until I absolutely have to (when I pass to the render method, which only takes integers). I'm not sure how to guarantee pixel perfect rendering precision when I'm rotating and scaling on a level of higher precision. Any advice? Do I need to supply for information?

  Read the article

• Can I install 64-bit OS on my Dell Inspiron 1545 laptop?

  - by Dell user

  My Dell Inspiron 1545 laptop features the Intel Pentium Dual Core T4200 processor. When I bought it, it came preinstalled with Windows Vista Home Basic, 32-bit. I'm considering upgrading it to Windows 7 Home Premium, but I don't know whether I should order the 64-bit or 32-bit version. The information I found on the web has been confusing. Does anyone know if my laptop supports 64-bit OS?

  Read the article

• How do I connect my NetXtreme BCM5755M Gigabit Ethernet PCI Express in y Dell latitude d630?

  - by Stanton.Sculpture

  Trying to get my 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5755M Gigabit Ethernet PCI Express (rev 02) working with my wifi. I just installed Raring Ringtail on this dell latitude D630 and I can't get it to connect without a wifi dongle. This is what I got when I typed sudo lshw -c network: *-network description: Ethernet interface product: NetXtreme BCM5755M Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 02 serial: 00:21:70:98:04:32 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.128 firmware=5755m-v3.29 latency=0 link=no multicast=yes port=twisted pair resources: irq:44 memory:fe8f0000-fe8fffff *-network description: Wireless interface physical id: 2 bus info: usb@2:1 logical name: wlan0 serial: 7c:dd:90:11:a0:10 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2800usb driverversion=3.8.0-31-generic firmware=0.29 ip=10.0.0.8 link=yes multicast=yes wireless=IEEE 802.11bgn Also, when I go to additional drivers in the software and updates settings, no proprietary drivers show up. I've tried sudo apt-get install b43-fwcutter firmware-b43-installer because it worked on a bunch of old Dell laptops that I converted over before, but it didn't work on this one. Is this driver even compatible with wifi? Please help.

  Read the article

• Dell Upgrade to 12.04 LTS No wifi, graphic card driver and bluetooth Problem?

  - by Mattlinux1

  (Dell inspiron m5040 Upgrade to 12.04 LTS from 11.10 wifi wont work and has two bluetooth icons?) Old title of post! No Wifi/Bluetooth Problem. "Both Fixed", see below comments for bluetooth fix and see bottom answer for wifi fix. My online upgrade of 12.04 LTS, was installed to my laptop the Dell inspiron m5040, when it was done i found that my wifi did not even get picked up anymore and i now have two bluetooth icons at the top?? So what i have been doing for now is at the boot screen. I hit the use previous linux version, this works fine but also has the two bluetooth at the top. Is very thankful for any answers for this fix, Thank You. Ok bluetooth problem solved by – fossfreedom answer by deleting the other bluetooth program running in software center. Now the other problem is Wifi: just have to restart system as it works in previous linux version boot opt, but on the first boot screen opt run ubuntu it will not pick up wifi drivers. Broadcom 802.11 Linux STA wireless driverfor use with Broadcom's BCM4311-, BCM4312-, BCM4313-, BCM4321-,BCM4322-, BCM43224-, and BCM43225-, BCM43227- and BCM43228-basedhardware. And 3D-accelerated proprietary graphics driver for ATI cards. This driver is required to fully utilise the 3D potential of some ATI graphics cards, as well as provide 2D acceleration of newer cards. will not instill is there anyway for me to make a copy of the drivers via usb HDD and then put them on new upgraded version.

  Read the article

• How do I get HDMI output working on a Dell XPS 15 L502x?

  - by Jones

  Recently I've bought my dream's notebook, a Dell XPS 15 but since then this dream became a kind of endless nightmare. I'm almost getting crazy to make my graphic card driver work properly, but it seems to be just impossible. Yes, I have a 2GB NVIDIA GeForce GT 540m (Optimus) in it! It simply doesn't work. Every time I generate the xorg.conf Ubuntu hangs on while starting up, which forces me to remove this file to be able to start the notebook with the standard graphic settings. Another problem is that the Dell XPS 15 does NOT have a VGA output, but a HDMI. So, to be able to use a second monitor I have to configure it by the NVIDIA X Server Settings, which just works if the driver is properly initialized with the xorg.conf. I've also tried to make it work with the Bumblebee, but unfortunately it didn't help me much with the HDMI output. Do you guys have any idea to solve this deadlock? Is there any way for me to use my second monitor?

  Read the article

• How can I configure the touchpad and keyboard settings on a Dell Inspiron 5110?

  - by Robik

  I am using ubuntu 11.10. I want the following 3 things: I have dell inspiron 5110 laptop. There is button at the top right corner of laptop which can be used for turning the screen off. It works in windows but it does not work in ubuntu 11.10. Even in the manual of the laptop, it the button is supported only in windows. Is there a way to activate it in ubuntu 11.10? Some of the keys like: "break" etc. are missing. Can I use other keys (or combinations of other keys) to function as those missing keys? In the program, "mouse and touchpad", there is no tab for touchpad. I want to enable vertical and horizontal scrolling. How do I do that? The command: xinput list shows Virtual core pointer id=2 [master pointer (3)] ? ? Virtual core XTEST pointer id=4 [slave pointer (2)] ? ? PS/2 Generic Mouse id=13 [slave pointer (2)] ? Virtual core keyboard id=3 [master keyboard (2)] ? Virtual core XTEST keyboard id=5 [slave keyboard (3)] ? Power Button id=6 [slave keyboard (3)] ? Video Bus id=7 [slave keyboard (3)] ? Video Bus id=8 [slave keyboard (3)] ? Power Button id=9 [slave keyboard (3)] ? Sleep Button id=10 [slave keyboard (3)] ? Laptop_Integrated_Webcam_HD id=11 [slave keyboard (3)] ? AT Translated Set 2 keyboard id=12 [slave keyboard (3)] ? Dell WMI hotkeys Please help!!

  Read the article

• Virtual Disk Degraded

  - by TheD

  There is a physical DC with a Raid 1 Mirror, 2 Physical Disks, 500GB each. Dell Server Administrator is installed on the DC, and is reporting both physical disks are fine, online, in a good state etc. On a PERC S300 Raid Controller: Physical Disk 0:0 Physical Disk 0:1 However at the same time it's reporting that a virtual disk is degraded, what exactly does this mean? The virtual disk indicates it's State is in a Raid 1 Layout. Device Name: Windows Disk 0 If my understanding is correct then the Virtual Disk, when you drill down into Dell OpenManage should have both physical disks as members, as it is a mirror? Is this correct? However, when I drill down into the Virtual Disk, it only displays Physical Disk 0:0 included in Virtual Disk 1. I'm very new to server side/raid management etc. just while our server techy is away! Thanks!

  Read the article

• Make laptop boot to external monitor

  - by Ozzy

  Hi all. Heres my setup: Dell 1737 2x Dell U2311H The laptop lid is always closed and is wall mounted behind the monitors. Every time i boot the laptop, i have to open the lid a little until it goes to the win 7 logon screen. Once there, i close the lid and both monitors get detected and the laptop screen switches off. As the laptop is wall mounted how ever, its really tedious to keep opening and closing the lid. Is there any way i can make it default to the external monitors permanently? Any suggestions are welcome, even hardware mods. Im willing to rip apart the laptop to install a switch or something if needs be lol

  Read the article

• Why Does My Laptop Freeze Up When Docked?

  - by Michael Haren

  I have a Dell Latitude D520. First with Windows XP and now with Windows 7, it completely freezes/locks up if I dock it while it's awake. If I hibernate/sleep, dock, then wake/resume, everything's fine. I installed the Dell Notebook System Software for Vista (No Win7 version available) and updated the bios to the latest version but the problem persists. As long as I remember to put this thing in standby before I dock it, it's extremely reliable--it survives my daily commute and heavy use and typically only reboots a few times a month. Any other ideas for things I can try?

  Read the article

• Dell OpenManage iDrac

  - by mhouston100

  I have installed OpenManage Server Administrator on a Windows 7 workstation with the assumption that nothing needed to be done on the actual server I am trying to manage. The server has an iDrac v7 component and I was under the impression that OpenManage just connects to that? When I try to connect I put the IP address of the iDrac console and the username/password and I get a 'Connection Error' message. So my question, does OpenManage have to be installed on the server that is to be managed, even if it has a DRAC connection?

  Read the article

• How to PERMANENTLY disable touchpad tap-to-click on Dell Inspiron/Windows 7

  - by Graham

  Hi all - my first time here, so I hope you can help. I've seen a lot of stuff on various forums (including here) about disabling the annoying "tap" function on a laptop touchpad. I learned the hard way not to de-install the driver (as the software suggests), since you then loose the Synaptic tab in the mouse control settings, and with it all means to modify the touchpad settings ... indicentally, if this happens to you, reboot in safe mode and do a restore, and the synaptic tab comes back. Not ideal, I know, but it works. Anyway, I have the most up-to-date drivers, and I can go to the Synaptics tab and can disable the tap-to-click function no problem. However, next time the machine is booted, tap-to-click is back on. It can alsways be disabled, but it's pain having to reset it every time the mchine is powered up. Is there a way to permanently disable it, once and for all? Thanks in advance, Graham

  Read the article

• Synaptics Touchpad on Dell Inspiron Stops Responding Sometimes.

  - by DaveDev

  Sometimes for no reason that I can observe my Synaptics touchpad will stop responding to scroll the scroll function (I swipe my finger down the right side). I then have to reboot to get it back. Does anyone know how to fix this? Preferably without upgrading the driver - I upgraded the driver before and it turned out to be crap. I don't want to do that again. I have an Inspiron 9400 with Windows XP Media Centre Edition

  Read the article

< Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >