Search Results

Search found 1360 results on 55 pages for 'is it plugged in'.

Page 13/55 | < Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >

  • Why isn't my phone charging with some micro usb cables?

    - by Jacxel
    I ordered 3 microUSB cables over ebay. My phone was at about 50% battery and I wanted to use it as a hot spot for some browsing on my laptop, so I plugged it in, a charging icon appeared on the phone, my laptop showed it as a connected usb device and so I went about my business. About 30 minutes later I checked the phone and to my dismay saw 45% battery. But ahh, I thought, I have been putting the poor little thing under too much pressure, acting as a WiFi hotspot must drain the battery quicker than it can charge via usb, perhaps even using my laptops usb port wouldn't output enough power. Unscathed I continued on and when I was going to bed I plugged the usb cable into a mains adapter and switched everything battery consuming off and content, went to sleep. The next morning I was awoken by my phones alarm which got cut off unexpectedly. I attempted to unlock my phone which showed no more signs of life. Why isn't my phone charging with these new USB cables? For clarity: They transfer data with no problems The phone appears to be charging, showing all the signs and lights it normally would, the cable that came with the phone works as you would expect, so its not a fault with the phone, I think they slow the discharging of the phone, but I could be wrong. Are these just bad quality cables? Is there a way to fix this issue?

    Read the article

  • Switched from DVI to HDMI, possible audio artifacts?

    - by I take Drukqs
    I'm using an ASUS VH236H monitor and an EVGA GeForce 570 GTX both of which are brand new. My monitor has an audio out port for speakers/headphones so I plugged in my headphones and made a random selection from my library when I noticed two things: There are static-like artifacts during "louder" parts of songs. There's what seems to be a volume cap in place. When I crank the volume past 100% in VLC the decibel level does not truly increase but the amount of static does. The cable is not new; I yanked it off of my PS3 when my DVI cable broke. It has been used a good amount on my HDTV and PS3 so I doubt it's a matter of burn-in. I like the way the setup works with an HDMI cable as opposed to DVI because my headphones barely reach my rig whereas I have plenty of slack when they're plugged into my monitor. Thanks in advance for any support. Note: I'm using a high quality HDMI cable from monoprice, AKG K702 headphones, and VLC media player.

    Read the article

  • WOL doesn't work if set to anything other than `a` but this setting makes it boot all the time

    - by Elton Carvalho
    I manage a small "cluster" of 4 Xeon machines with Intel boards in my lab. They are all plugged to a 5-port 3-Com switch with static IP addresses like 10.0.0.x. They are all running OpenSuse 11.4 and their /home/ is served by one of the machines (node00) via NFS. They are plugged to an UPS that can keep them on for ca. 15 minutes, but there are lots of electric shortages due to "unscheduled maintenace" that are longer than this. So they end up being powered down without notice. If I set the BIOS to turn them on after power shortages, the issue is that they all boot at the same time and, if node00 decides to run fsck in the /home/ partition, it does not finish booting before the others try to NFS mount their /home/. I am trying to make wake on lan work, so I can choose to boot the NFS clients only after the server has successfully booted. The problem is that when I run ethtool I get an output like this: Supports Wake-on: pumbag Wake-on: g Theoretically, it is set to wake on MagicPacket(tm), according to the manual. But sending the WOL packet using wol -i 10.0.0.255 $MACADDR does not wake up the box after I shut it down with halt. The ethernet link led blinks after I send the packet, so it appears to be getting to the machine. However, if I set it up with ethtool -s eth1 wol bag, the machine always wakes up right after halting, even if I don't send the Magic packet. This means that the device can wake up with LAN activity, but seems to be ignoring the magic packet. Setting wol ag does not wake the box with the MagicPacket. Does setting wol a mean that it should boot with any broadcast message? How can I diagnose the issue of the machine not waking up with the MagicPacket even though I am sending it and it's set up to wake up with it? Thanks in advance!

    Read the article

  • Power supply switch like stays off motherboard light turns on

    - by Sion
    I bought a computer at the thrift store yesterday. The computer powered on without any error beeps. Getting it back to the house determined that the CD and hard drive needed to be changed. Put in a populated hard drive to check, the computer turned on and seemed to function. Put in a new CD drive, and just put in a new Hard drive. I plugged it in to check and I noticed that the light for the power supply switch did not come on. But I did notice that the light on the motherboard is lit. and I could not turn the computer on. To help troubleshoot it I unplugged the CD and Hard drive. then re-plugged the power supply and switched it on and off. Nothing changed. Parts: Motherboard: Digital Home PSW DH deluxe Power Supply: FSP-Group FX700-GLN Did I accidentally unplug something while installing the hard drive? Is the Power supply fried somehow?

    Read the article

  • Known USB 2.0 devices don't install driver, but must be manually forced

    - by Darragh
    When a known USB 2.0 device is plugged in and detected, it doesn't install the driver correctly but shows a Code 28 error and lists the device under "Other Devices" in Device Manager. When view properties of this device , it shows the following status; The drivers for this device are not installed. (Code 28) There is no driver selected for the device information set or element. To find a driver for this device, click Update Driver. When updating the driver manually and selecting the appropriate driver Windows doesn't believes it's the correct driver, but you can force the installation and it works! The other condition the driver will auto-install is when the same USB device is plugged into a USB 3.0 port. Power related issues are not also causing this as I have tried vi a Docking station, USB hub. etc.. Devices tried; Jabra Headset USB-Mass Storage Device (flash disk and ext HD) MS Wireless Keyboard & Mouse USB Ethernet controller (USB-MAC controller) This is on a laptop part of a Domain with Windows 7 Ent 7601, I am logged in as a local administrator. There isn't any Group Policies blocking not signed driver or whitelisted devices on the domain. Any suggestions please feel free

    Read the article

  • Docking Station Sound Doesn't Work on Dell D830 with Windows 7

    - by cisellis
    EDIT: I can only mark one answer as the correct one but the actual solution was a combination of two comments (updating the BIOS to A15 AND installing the Sigmatel audio drivers). I have a Dell Latitude D830 laptop that is running Windows 7 Enterprise x64. I connect to a docking station during the day with multiple monitors, a keyboard and a mouse. Everything runs with no problems including most of the docking station ports (usb, monitors, etc.) However, the sound port from the docking station does not work since the upgrade to Windows-7. Even with the laptop plugged in, the sound always comes out of the laptop, not the headphones plugged into the docking station. Here's what I've tried: I've seen other issues like via Google this that seem to be mostly unanswered. I found one or two that referenced using the Vista x64 drivers, especially the Nvidia drivers. I do not have an Nvidia chipset but I've reinstalled the sound drivers and that has not helped. I don't have a support contract and considering the cost is usually high to call Dell, that's not an option. Dell's forums are pretty much a wasteland and I've found no help there. Since this is a docking station I thought I might need to try the SATA or Intel chipset drivers from the dell site instead, however I'm not really sure and I need to work on this laptop in the meantime. I can't really afford the downtime to experiment with random drivers all day in case they turn out to be incompatible (Dell still hasn't added Windows 7 to their support site as far as I can tell). Does anyone have any other ideas? Has anyone had this issue and solved it? If so, how? Thanks in advance for your help.

    Read the article

  • Gigabyte H55N-USB3: No video on HDMI

    - by newt
    I built a new PC with a Gigabyte H55N-USB3 / Intel Core i5 650. With a monitor plugged in the DVI port, everything works fine. I installed Windows 7 32-bit and enabled remote desktop connection. After that, I unplugged the monitor, plugged it into network and installed everything else (drivers, programs, etc) via RDP. However, when I try to use the HDMI port on my TV nothing appears. Neither during the boot, neither after Windows starts. The TV says there's "no signal" (if I remove the cable the message changes to "check cable"). The cable is new, and it is working fine with my home theater on same TV (by the way, it is the cable which came bundled with the home theater). Video driver is the latest from Intel site. Anyway, this shouldn't be the problem since there is no image during the boot. Any ideas or tips would be welcome. I'm googling around but found nothing useful, yet.

    Read the article

  • Computer making strange sound when turned on, ever since power outage

    - by Dot NET
    Recently we experienced a power outage, and the PC was off. However, once the power came back, I switched on the PC and heard a strange noise - almost as if the hard disk or fans were struggling to work. I can't really describe the sound, but it's a laboured, loud sound almost like a jack-hammer. This has been persisting ever since the power outage, however the noise stops after around 10 minutes or so, and doesn't start again until the computer is turned off and on again. At first I thought it had something to do with the HDD, but all my files are intact, chkdsk did not report any issues and performance is 100% unchanged, even in games (so the gfx card is fine, and so is the HDD most likely). My PC setup basically has around 3 cooling fans, but I'm not sure if it's one of these either as the noise actually stops after 10 minutes or so, and if I leave the PC on for 4 hours (for example) the noise never starts again. It's there solely when turning on the PC. I haven't got a UPS, and it's important to note that the computer was not on when the power went out - it was merely plugged in. I then promptly unplugged the PC once the power was out, and only plugged it in again when the power came back. Could it be the power supply? Unfortunately I can't open my tower as I would void the warranty. Are there any tests which I could carry out without voiding the warranty?

    Read the article

  • Motorola Surfboard SB6121 modem conected to 2WIREi38HG wireless router but there's no internet access

    - by Jessica
    I have just switched to Comcast cable internet from AT&T Uverse and I was hoping to use the 2WIRE wireless router with the new Surfboard modem so I can have wireless access. I messed around with some settings and got it working for my laptop (I'm not terribly well versed in computer stuff; I think it was mostly luck) for about a week. The other day I tried to get online and there was no internet connection. I restarted the equipment with no success and then plugged the modem directly into the laptop. This worked, so I knew there was no outage. I connected the ethernet cord to the router and a second cord to my laptop and that worked, too. But when I tried again just with the wireless the laptop connects to the router, but doesn't recognize it or find an internet connection. I tried to go to http://gateway.2Wire.net to fiddle with the settings, but all I get is a Server Not Found page. I tried to check the ip address but this is really kind of over my head and I get different things checking it while plugged into only the modem vs when I plug into the router. Can anyone help? The frustrating thing is that I had it working for awhile, so I know it can do it!

    Read the article

  • Why does 3.5 mm audio out work through headphones but not through external speakers?

    - by Rickster
    I have a computer that has a 3.5 mm audio jack on the front of it. The computer itself has no speakers, so this is the only way to hear sound. If I plug headphones into it, the audio properly plays through the headphones, and if I plug in external speakers it used to play through them as well. Just today I turned on my computer and the audio no longer plays through the speakers, but if I plug in the headphones instead it works. The speakers aren't broken, as both the speakers and headphones work in my iPod and play music. I thought that 3.5 mm jacks could not send data back to the computer, and the computer had no way of differentiating between different devices plugged into the jack. If this is true, how is it that the computer plays audio through the headphones but not through speakers plugged into the same 3.5 mm jack, and both devices are functional? Or is my knowledge on 3.5 mm jacks incorrect? I don't believe drivers are important, as the same driver runs the 3.5 mm jack for all devices, but if necessary I can provide additional information. Any ideas would be appreciated. Thanks!

    Read the article

  • USB Device Not Recognized (Mac)

    - by Nargis
    Fortunately, my Mac-pro also made one of my USB storage devices inoperable. My data loss in that USB device but such as another USB device and USB keyboard are unaffected. I have heard that my friend usually trigger this problem by having at least two devices plugged in - typically thumb drives/USB flash drives, and then once a second flash drive is plugged in that become unrecognized. I have only two USB ports and first I think port loose when I connect two USB devices. But later I found these hidden files (“.Spotlight-V100”, “.TemporaryItems”, “.Trashes”, and “._.Trashes”) are created by Mac OS. And before unrecognized that USB device I have deleted these files and my friend had also done the same action. Now I don’t want to test for next USB device to become unrecognized and I won’t deleted any hidden system file inside the flash drives. But I really want to know why these problems happened. Can I delete these hidden files when I only connect to virtual machine (Vista), because I used to delete all useless hidden files from USB flash drives? Any suggestions or thoughts to prevent this or alternative suggestions to fix the problem that take lossless would be much appreciated.

    Read the article

  • Can't detect hard drive on Macbook Pro

    - by MartinMoizard
    I changed a few month ago the config of my Macbook Pro with the following: I bought a SSD hard drive I removed the hard drive of my Mac book Pro and installed there my brand new SSD Then I removed my DVD drive and installed my hold hard drive instead with a caddy Everything was working great until today when I couldn't access anymore to my old hard drive because it is not detected anymore. Sometimes Mac OSX is mounting it but it takes like 15 min to browse a simple folder. I opened my laptop to have a look at the problem. It seemed like the optical drive connector was not plugged correctly to the motherboard (that connector: http://cl.ly/2T0X2e1j0J1g47061d1t). So I plugged it correctly and reboot. It didn't fix my problem. Then I tried to put my SSD in the caddy and to boot: no hard drive was detected. So I guess there is something wrong either with the caddy, either with the optical drive connector, or either with the plug that is on the motherboard. So my question is, how can I know where the problem comes from?

    Read the article

  • Configuring two nearby WLANs: should I use the same ssid?

    - by Rory
    I'm configuring a home network for basic internet use (ie don't really need connectivity between workstations on the network). My brick walls mean a single wireless router doesn't provide good coverage throughout the house, so I have purchased two powerline adapters and now have the incoming modem/wireless router at one end of the house plugged into a powerline adapter, and at the other end of the house the other powerline adapter plugged into another wireless router. Currently the two wireless networks have different ssids. (The powerline adapters only do power-Ethernet; they're not wireless access points themselves.) This works well, except when I move between rooms and would ideally like my devices (iPad, phones, laptops) to switch from the weak to the strong signal. Sometimes there's enough signal that they hold on to the weak connects instead of switching to the strong one. Should I name the two networks the same ssid, and if so what is the actual effect? Do the signals get confused, is the bandwidth affected, will this help my devices seamlessly move from one to the other, or is the ssid just a cosmetic thing that actually doesn't have any impact on this situation? Are there any other settings that I should configure to make my setup optimal?

    Read the article

  • Replaced CPU and black screen but no beep?

    - by luke
    I'm having a bit of trouble with a GIGABYTE GA-MA78G-DS3H (rev. 2.0) motherboard. Recently when trying to clean my AMD Phenom II X 4 CPU, I dropped it and broke some pins. I have now brought a Athlon 64 X2 5400+. However, it does not seem to work. To begin with, I cleared the CMOS via the jumper located near the battery. This was because I had my AMD Phenom II overclocked and did not wish for the same voltage to go to the new CPU. I then tried booting with the monitor plugged into the chipsets VGA but no luck. No signal was sent to the monitor, and the monitor just went into standby. I then tried it off the graphics card but the same happened again. Then I tried to check whether the CPU could executed some BIOS codes by stripping the RAM out and making sure a speaker was plugged in but no beeps could be heard. I replaced the speaker and tried again but no luck. The CPU is brand-new so what is going wrong?

    Read the article

  • Tried to install Mint to a Flash Drive. Now I can't boot from the main hard disk.

    - by Dan
    Hello, all. I'm kind of new to Linux and I need some help. I wanted to install a Linux distro to a flash drive so that I can have a portable OS with all my settings, programs, etc. wherever I go. So I fired up a Linux Mint Live CD and installed Mint to the flash drive, and this seems to work OK. But now, whenever I try to boot up my system normally without the flash drive plugged in, it doesn't seem to work. It basically hangs for a bit, and then I get the following prompt: error: no such device: (some long hex val) grub rescue> However, when I try powering my system up when the USB is plugged into the computer, it gives me an option between using the OS installed on my USB and the OS installed on my HD. Selecting the latter, everything loads up just fine. I'm guessing that installing Mint to the flash drive somehow messed with my native Grub installation, but, again, I'm kind of new to Linux, so I'm not sure exactly why. Any help is greatly appreciated.

    Read the article

  • Static IP addressing issue in Ubuntu on BeagleBoneBlack Rev C

    - by Stringfellow
    I have my BBB configured to use a static IP address using the following in the file /etc/network/interfaces: allow-hotplug eth0 iface eth0 inet static address 192.168.0.1 netmask 255.255.255.0 network 192.168.0.0 This seems to work ok on boot, but when the ethernet cable is unplugged and then plugged back in, I lose the IP address. Any ideas what's going on here? Another weird symptom: If I boot the BBB with the network cable unplugged, but the switch it's plugged into off, I'll get my static IP. But, when I turn the switch on, I'll get a DHCP-assigned address. This is even though I have it configured with a static IP address. One last thing. If I ifdown etho, the interface will be gone when I do an ifconfig. If I wait a few seconds, though, and then re-run ifconfig, it will reappear, without an IP address. (Before I disabled IPv6, I used to get a IPv4 DHCP address in this case... weird). When that happens, I get a message like this in /var/log/messages: Apr 23 20:32:06 beaglebone kernel: [ 737.170172] libphy: 4a101000.mdio:00 - Link is Up - 100/Full Apr 23 20:32:06 beaglebone kernel: [ 737.170304] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Here's my uname -a: root@beaglebone:/etc# uname -a Linux beaglebone 3.8.13-bone47 #1 SMP Fri Apr 11 01:36:09 UTC 2014 armv7l GNU/Linux Any ideas what's going on here?

    Read the article

  • Which Cardbus/PCMCIA -> USB card works with external hard drive?

    - by Carl
    I have an HT-Link Cardbus/PCMCIA USB 2.0 2-port card (NEC / 32-bit). My external hard drive w/USB adapter won't work with it, and it will work plugged directly into a USB port on a different laptop. (My USB ports got fried.) I got the card off E-Bay. My MP3 player works plugged into that card. The drivers for the card say "Known limitations: High Speed Isochronus, USB Composite Devices." (No other details provided.) I don't know if the hard drive adapter is "isochronous" or "composite." I've read there are problems with too little power being supplied to the drive. The cable to the drive has two USB plugs on one end, and it doesn't make any difference if I plug both of them into the Cardbus card. What card should I get? I see many different brands on E-Bay. I need one that supplies sufficient power for an external hard drive, and doesn't have any "known limitations" in the way.

    Read the article

  • My PC suddenly reboots

    - by ChocoDeveloper
    Yesterday I opened my PC hub (after like, 5 years) to add more RAM and a new HDD. It was full of dust and balls of fluff, so I cleaned it a bit by blowing. I also removed the fan that was attached to the motherboard (I think it's there to cool the processor) and I cleaned it also by blowing and with a paintbrush, then put it back where it was (it had 4 weird plastic screws, it wasn't easy). Then I added 2 x 2Gib of RAM (Kingston 1333MHz), and the new HDD (Western Digital Caviar Blue 1TB SATA 3). I couldn't find another wire like the one my first disk had, which was thicker, but there was one that was more flat, so I plugged it and it worked fine (I also plugged the wire that I think is for the data, which looks like many little wires glued together). I'm running Ubuntu 12.04, and in the new disk I've just installed Windows 7. Between yesterday and today, two reboots ocurred while working on Ubuntu. I haven't used Windows 7 that much so I don't know if it will happen there too. So where can I begin to debug this?

    Read the article

  • Need recommendation: which USB card (PCMCIA) works with external hard drive?

    - by Carl
    I have an HT-Link Cardbus/PCMCIA USB 2.0 2-port card (NEC / 32-bit). My external hard drive w/USB adapter won't work with it, and it will work plugged directly into a USB port on a different laptop. (My USB ports got fried.) I got the card off E-Bay. My MP3 player works plugged into that card. The drivers for the card say "Known limitations: High Speed Isochronus, USB Composite Devices." (No other details provided.) I don't know if the hard drive adapter is "isochronous" or "composite." I've read there are problems with too little power being supplied to the drive. The cable to the drive has two USB plugs on one end, and it doesn't make any difference if I plug both of them into the Cardbus card. What card should I get? I see many different brands on E-Bay. I need one that supplies sufficient power for an external hard drive, and doesn't have any "known limitations" in the way.

    Read the article

  • arp problems with transparent bridge on linux

    - by Mink
    I've been trying to secure my virtual machines on my esx server by putting them behind a transparent bridge with 2 interfaces, one in front, one at the back. My intention is to put all the firewall rules in one place (instead of on each virtual server). I've been using as bridge a blank new virtual machine based on arch linux (but I suspect it doesn't matter which brand of linux it is). What I have is 2 virtual switchs (thus two Virtual Network, VN_front and VN_back), each with 2 types of ports (switched/separated or promiscious/where the machine can see all packets). On my bridge machine, I've set up 2 virtual NIC, one on VN_front, one on VN_back, both in promisc mode. I've created a bridge br0 with both NIC in it: brctl addbr br0 brctl stp br0 off brctl addif br0 front_if brctl addif br0 back_if Then brought them up: ifconfig front_if 0.0.0.0 promisc ifconfig back_if 0.0.0.0 promisc ifconfig br0 0.0.0.0 (I use promisc mode, because I'm not sure I can do without, thinking that maybe the packets don't reach the NICs) Then I took one of my virtual server sitting on VN_front, and plugged it to VN_back instead (that's the nifty use case I'm thinking about, being able to move my servers around just by changing the VN they are plugged into, without changing anything in the configuration). Then I looked into the macs "seen" by my addressless bridge using brctl showmacs br0 and it did show my server from both sides: I get something that looks like this : port no mac addr is local? ageing timer 2 00:0c:29:e1:54:75 no 9.27 1 00:0c:29:fd:86:0c no 9.27 2 00:50:56:90:05:86 no 73.38 1 00:50:56:90:05:88 no 0.10 2 00:50:56:90:05:8b yes 0.00 << FRONT VN 1 00:50:56:90:05:8c yes 0.00 << BACK VN 2 00:50:56:90:19:18 no 13.55 2 00:50:56:90:3c:cf no 13.57 the thing is that the server that are plugged in front/back are not shown on the correct port. I suspect some horrible thing happening in the ARP-world... :-/ If I ping from a front virtual server to a back virtual server, I can only see the back machine if that back machine pings something in the front. As soon as I stop the ping from the back machine, the ping from the front machine stops getting through... I've noticed that if the back machine pings, then its port on the bridge is the correct one... I've tried to play with the arp_ switch of /proc/sys, but with no clear effect on the end result... /proc/sys/net/ipv4/ip_forward doesn't seem to be of any use when using a bridge (seems it's all taken care of by brctl) /proc/sys/net/ipv4/conf//arp_ don't seem to change much either... (tried arp_announce to 2 or 8 - like suggested elsewhere - and arp_ignore to 0 or 1 ) All the examples I've seen have a different subnet on either side like 10.0.1.0/24 and 10.0.2.0/24... In my case I want 10.0.1.0/24 on both side (just like a transparent switch - except it's a hidden fw ). Turning stp on/off doesn't seem to have any impact on my issue. It's as if the arp packets where getting through the bridge, corrupting the other side with false data... I've tried to use the -arp on each interface, br0, front, back... it breaks the thing altogether... I suspect it has something to do with both side being on the same subnet... I've thought about putting all my machine behind the fw, so as to have all the same subnet at the back... but I'm stuck with my provider's gateway standing at the front with part of my subnet (in fact 3 appliance to route the whole subnet), so I'll always have ips from the same subnet on both side, whatever I do... (I'm using fixed front IPs on my delegated subnet). I'm at a loss... -_-'' Thx for your help. (As anyone tried something like this? from within ESXi?) (It's not just a stunt, the idea is to have something like fail2ban running on some servers, sending their banned IP to the bridge/fw so that it too could ban them - saving all the other servers from that same attacker in one go, allowing for some honeypot that would trigger the fw from any kind of suitable response, and stuffs of the sort... I am aware I could use something like snort, but it addresses some completely different kind of problems, in a completely different way... )

    Read the article

  • How do you install a USB CD Rom drive?

    - by Matt Allen
    Hello, I recently purchased a USB CD ROM drive, but I don't know how to get it to work with my computer which runs Ubuntu 10.04. http://www.amazon.com/gp/product/B00303H908/ref=oss_product When I issue the lsusb command, it shows up as: Bus 002 Device 016: ID 05e3:0701 Genesys Logic, Inc. USB 2.0 IDE Adapter The computer doesn't recognize it automatically. How can I get this drive to show up as an actual drive on my computer? If this particular drive can't handle Linux, can you recommended one which can and provide a link to it so I can purchase it? Thanks! Update: I was asked by Scaine to run a command and report back with the output: joe@joe-laptop:~$ tail -f /var/log/kern.log Dec 29 12:51:35 joe-laptop kernel: [103190.551437] sr 7:0:0:0: [sr1] Add. Sense: Illegal mode for this track Dec 29 12:51:35 joe-laptop kernel: [103190.551446] sr 7:0:0:0: [sr1] CDB: Read(10): 28 00 00 00 00 00 00 00 02 00 Dec 29 12:51:35 joe-laptop kernel: [103190.551463] end_request: I/O error, dev sr1, sector 0 Dec 29 12:51:35 joe-laptop kernel: [103190.877542] sr 7:0:0:0: [sr1] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Dec 29 12:51:35 joe-laptop kernel: [103190.877551] sr 7:0:0:0: [sr1] Sense Key : Illegal Request [current] Dec 29 12:51:35 joe-laptop kernel: [103190.877559] Info fld=0x0, ILI Dec 29 12:51:35 joe-laptop kernel: [103190.877562] sr 7:0:0:0: [sr1] Add. Sense: Illegal mode for this track Dec 29 12:51:35 joe-laptop kernel: [103190.877572] sr 7:0:0:0: [sr1] CDB: Read(10): 28 00 00 00 00 00 00 00 02 00 Dec 29 12:51:35 joe-laptop kernel: [103190.877588] end_request: I/O error, dev sr1, sector 0 Dec 29 13:08:46 joe-laptop kernel: [104221.558911] usb 2-2.2: USB disconnect, address 16 Then when I plugged the drive back into the computer, I got: Dec 29 13:10:29 joe-laptop kernel: [104324.668320] usb 2-2.2: new high speed USB device using ehci_hcd and address 17 Dec 29 13:10:29 joe-laptop kernel: [104324.761702] usb 2-2.2: configuration #1 chosen from 1 choice Dec 29 13:10:29 joe-laptop kernel: [104324.762700] scsi8 : SCSI emulation for USB Mass Storage devices Dec 29 13:10:29 joe-laptop kernel: [104324.762935] usb-storage: device found at 17 Dec 29 13:10:29 joe-laptop kernel: [104324.762938] usb-storage: waiting for device to settle before scanning Dec 29 13:10:34 joe-laptop kernel: [104329.760521] usb-storage: device scan complete Dec 29 13:10:34 joe-laptop kernel: [104329.761344] scsi 8:0:0:0: CD-ROM TEAC CD-224E 1.7A PQ: 0 ANSI: 0 CCS Dec 29 13:10:34 joe-laptop kernel: [104329.767425] sr1: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray Dec 29 13:10:34 joe-laptop kernel: [104329.767612] sr 8:0:0:0: Attached scsi CD-ROM sr1 Dec 29 13:10:34 joe-laptop kernel: [104329.767720] sr 8:0:0:0: Attached scsi generic sg2 type 5 Dec 29 13:10:34 joe-laptop kernel: [104330.141060] sr 8:0:0:0: [sr1] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Dec 29 13:10:34 joe-laptop kernel: [104330.141069] sr 8:0:0:0: [sr1] Sense Key : Illegal Request [current] Dec 29 13:10:34 joe-laptop kernel: [104330.141077] Info fld=0x0, ILI Dec 29 13:10:34 joe-laptop kernel: [104330.141081] sr 8:0:0:0: [sr1] Add. Sense: Illegal mode for this track Dec 29 13:10:34 joe-laptop kernel: [104330.141090] sr 8:0:0:0: [sr1] CDB: Read(10): 28 00 00 00 00 00 00 00 02 00 Dec 29 13:10:34 joe-laptop kernel: [104330.141106] end_request: I/O error, dev sr1, sector 0 Dec 29 13:10:34 joe-laptop kernel: [104330.141113] __ratelimit: 18 callbacks suppressed There was more output than this (the number of lines started growing after the drive was plugged back in, and kept growing), but this is the first few lines.

    Read the article

  • LSI SAS 9240-8i on Ubuntu 12.04 Hangs on Modprobe

    - by Francois Stark
    I used the LSI 9240-8i card on a smaller Intel motherboard with no problems in Ubuntu, with ZFS. However, we rebuilt the server to allow for more disks, using the ASROCK X79 Extreme 11 motherboard. It has 7 PCIe slots, and a LSI 2008 on-board. At first I thought the LSI 9240, when plugged in to PCIe, clashed with the on-board LSI 2008. Every time I plugged in the LSI 9240, modprobe would hang. Then I completely disabled the on-board LSI 2008, and the problem persisted. Last night it booted perfectly ONCE - all LSI cards and connected disks visible... However, all subsequent reboots failed. Both LSI cards' bios scans appear and they both see the disks connected to them, but Ubuntu modprobe hangs. Some selected dmesg lines, with both LSI cards enabled: [ 190.752100] megasas: [ 0]waiting for 1 commands to complete [ 195.772071] megasas: [ 5]waiting for 1 commands to complete [ 200.792079] megasas: [10]waiting for 1 commands to complete [ 205.812078] megasas: [15]waiting for 1 commands to complete [ 210.832037] megasas: [20]waiting for 1 commands to complete [ 215.852077] megasas: [25]waiting for 1 commands to complete [ 220.872072] megasas: [30]waiting for 1 commands to complete [ 225.892078] megasas: [35]waiting for 1 commands to complete [ 230.912086] megasas: [40]waiting for 1 commands to complete [ 235.932075] megasas: [45]waiting for 1 commands to complete [ 240.306157] usb 2-1.5: USB disconnect, device number 7 [ 240.952076] megasas: [50]waiting for 1 commands to complete [ 240.960034] INFO: task modprobe:233 blocked for more than 120 seconds. [ 240.960055] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 240.960067] modprobe D ffffffff81806200 0 233 146 0x00000004 [ 240.960075] ffff880806ae3b48 0000000000000086 ffff880806ae3ae8 ffffffff8101adf3 [ 240.960083] ffff880806ae3fd8 ffff880806ae3fd8 ffff880806ae3fd8 0000000000013780 [ 240.960090] ffffffff81c0d020 ffff880806acae00 ffff880806ae3b58 ffff880808961720 [ 240.960096] Call Trace: [ 240.960107] [<ffffffff8101adf3>] ? native_sched_clock+0x13/0x80 [ 240.960116] [<ffffffff816579cf>] schedule+0x3f/0x60 [ 240.960137] [<ffffffffa00093f5>] megasas_issue_blocked_cmd+0x75/0xb0 [megaraid_sas] [ 240.960144] [<ffffffff8108aa50>] ? add_wait_queue+0x60/0x60 [ 240.960154] [<ffffffffa000a6c9>] megasas_get_seq_num+0xd9/0x260 [megaraid_sas] [ 240.960164] [<ffffffffa000ab31>] megasas_start_aen+0x31/0x60 [megaraid_sas] [ 240.960174] [<ffffffffa00136f1>] megasas_probe_one+0x69a/0x81c [megaraid_sas] [ 240.960182] [<ffffffff813345bc>] local_pci_probe+0x5c/0xd0 [ 240.960189] [<ffffffff81335e89>] __pci_device_probe+0xf9/0x100 [ 240.960197] [<ffffffff8130ce6a>] ? kobject_get+0x1a/0x30 [ 240.960205] [<ffffffff81335eca>] pci_device_probe+0x3a/0x60 [ 240.960212] [<ffffffff813f5278>] really_probe+0x68/0x190 [ 240.960217] [<ffffffff813f5505>] driver_probe_device+0x45/0x70 [ 240.960223] [<ffffffff813f55db>] __driver_attach+0xab/0xb0 [ 240.960227] [<ffffffff813f5530>] ? driver_probe_device+0x70/0x70 [ 240.960233] [<ffffffff813f5530>] ? driver_probe_device+0x70/0x70 [ 240.960237] [<ffffffff813f436c>] bus_for_each_dev+0x5c/0x90 [ 240.960243] [<ffffffff813f503e>] driver_attach+0x1e/0x20 [ 240.960248] [<ffffffff813f4c90>] bus_add_driver+0x1a0/0x270 [ 240.960255] [<ffffffffa001e000>] ? 0xffffffffa001dfff [ 240.960260] [<ffffffff813f5b46>] driver_register+0x76/0x140 [ 240.960266] [<ffffffffa001e000>] ? 0xffffffffa001dfff [ 240.960271] [<ffffffff81335b66>] __pci_register_driver+0x56/0xd0 [ 240.960277] [<ffffffffa001e000>] ? 0xffffffffa001dfff [ 240.960286] [<ffffffffa001e09e>] megasas_init+0x9e/0x1000 [megaraid_sas] [ 240.960294] [<ffffffff81002040>] do_one_initcall+0x40/0x180 [ 240.960301] [<ffffffff810a82fe>] sys_init_module+0xbe/0x230 [ 240.960307] [<ffffffff81661ec2>] system_call_fastpath+0x16/0x1b [ 240.960314] INFO: task scsi_scan_7:349 blocked for more than 120 seconds.

    Read the article

  • Graphics trouble after resuming from hibernate or suspend

    - by Voyagerfan5761
    I have a Dell Inspiron 2650 (with NVidia graphics, using nouveau drivers) that I'm using to try out Ubuntu. It's all great, except that Hibernate and Suspend aren't usable. Yes, I know that questions about power-save issues are rampant in the Linux support universe, but it seems that every time I find a solution it's for a very specific hardware combination and doesn't apply to me. So anyway, here goes. When I resume from either power-saving mode, I'll get graphics problems anywhere on the range from a few scattered random-colored pixels that won't change; all the way to full-screen patterns that don't change as I move the mouse, hit keys on the keyboard, or even bring up the shutdown dialog using the power button. Those full-screen issues (which may involve stripes with random pixels, partial black screen, or both) always end in me forcing the machine to shut down by holding the power button. I haven't done much testing yet to determine what severity level is most commonly associated with each mode, but I do avoid using either power-save option because of these issues. I'll add info on my hardware as I can gather it (no home internet connection, and this laptop is tethered to my desk by a dead battery and casing degradation). Please feel free to request something specific in the question comments. Hardware Info See this hardinfo report for my system's hardware configuration. (No, my username is not "myuser"; I sanitized hardinfo's output before publishing it.) Screenshots These screenshots are from a relatively mild occurrence, which happened after the second hibernation I took that session. The first one worked great, though I used the wireless card and Firefox heavily between the two hibernation attempts. Take a look at what happened when I opened my home directory in Nautilus and scrolled it: See below for the situations I've tested so far. The real trouble comes when the machine resumes to an unusable state; in such cases I can't even unlock the screen or properly reboot, much less take a screenshot. I have a hunch that putting a CD in the drive will cause such major failures, and I will try that at some point; see related question. Situations Tested Maverick (10.10) Suspend Seems to suspend nicely with nothing running Seems to suspend nicely with flash drive plugged in On resume from suspend with no flash drive, Terminal and gedit running: Funky graphics on top of log output, then blank screen with pixelated cursor; no response to power button (normally will shutdown 60 seconds later) Hibernate Seems to hibernate nicely with nothing running Seems to hibernate nicely with a few apps (Terminal, Mouse preferences) running Seems to not hibernate when flash drive plugged in Seems to not hibernate when System Monitor is running Have encountered failed hibernation (after several hours and one successful hibernate/thaw cycle) with no external media connected and no programs running except normal background stuff Natty LiveCD (11.04_2010-12-22) When I tested it, Natty wouldn't stay logged in. It played part of the login sound and then [ OK ] appeared in the top right corner (white-on-black terminal text) for a few seconds. Then it kicked me back to the Unlock screen. It did that four times before I gave up and just tested suspend from the Unlock screen. Suspend Resumed to vertical gray and black lines 2px (?) wide, then shifted to vertical "jail bars" of black over a black screen with above-described random pixels and mouse pointer. No apparent response to input from mouse (clicking randomly). Keyboard and touchpad unrecognized.

    Read the article

  • Access VBA question: Change the query being referenced by a function, depending on context

    - by Tara Amatista
    I have a custom function in Access2007 that hinges on grabbing data out of a specific query. It opens Outlook, creates a new email and populates the fields with specific addresses and data taken from the query ("DecisionEmail"). Now I want to make a different query ("RequestEmail") and have it populate the email with that data. So all I have to do is change this line: Set MailList = db.OpenRecordset("DecisionEmail") and that's where I get stumped. This is my desired result: If the user is on Form_Decision and clicks the button "Send email", "DecisionEmail" will get plugged into the function and that data will appear in the email. If the user on Form_SendRequest and clicks the button "Send email", "RequestEmail" will instead get plugged in. The reason that these are different queries is because they contain very different information that is smudged about in different ways. However, since it's just one little thing that needs to change in the function code, I don't think a brand new function is a good idea. My last resort would be to make a brand new function and use the Conditions field in the Macro interface to choose between them, but I have a feeling there's a more elegant solution possible. I have a vague notion of setting the query names as variables and using an If statement but I just don't have the mental vocabulary for thinking through this.

    Read the article

  • TCP/IP RST being sent differently in different browsers.

    - by Brian
    On Mac OS X (10.6), if I start a YouTube video download and pull the Ethernet cable for 5 or so seconds, then plug it back in, I get varying results depending on the browser. With Opera and Chrome, after I plug the cable back in the video continues to load. But with Safari and Firefox, it never does. Using Wireshark to look at the traffic, I found that Opera and Chrome simply ACK the first packet from YouTube after the cable has been plugged back in, but Safari and Firefox set the RST flag (0x4) in the TCP header and no more traffic follows. I can put a HUB in between the machine and the internet connection, the problem goes away and all four browsers continue loading the video when the cable is plugged back into the HUB. Again, looking at the Wireshark logs, it's evident that the machine doesn't see the Mulitcast connection close and there is simply a delay in the packets flowing through. So it seems that if Safari and Firefox sees a Multicast connection close, and then later see data on that same connection, they will send a RST. My question is why? What is the correct course of action, and why are 2/4 browsers doing it one way, while the other 2/4 are doing it another way? Is there somewhere in the code that I can see where this is happening in Firefox, for instance? Thank you very much.

    Read the article

< Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >