Search Results

Search found 3084 results on 124 pages for 'lan'.

Page 13/124 | < Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >

• Packet loss with all adapters on one PC only on the LAN

  - by Enigmativity

  I have a Windows 7 64-bit machine that is losing up to 20% of IP packets on both adapters - wireless & LAN. Browser traffic appears to be affected the most, but it is happening to all protocols. All other computers on the network are functioning fine. If I ping from my faulty machine to any machine on the LAN (wired or wirelessly), including the router/gateway and internet sites, I get up to 20% packet loss. If I do the following commands: ipconfig /release ipconfig /renew then I sometimes get my network performance back for a matter of a few seconds to less than a couple of minutes. Rebooting also works for a short period of time. This problem has been occurring for a couple of months and is getting worse. The computer used to work just fine. I updated the wireless adapter firmware the other day with no effect. Does anyone know what is happening?

  Read the article

• squid configuration change to accept http request on LAN

  - by Ratan Kumar

  installed squid + dansguardian to block adult content on my linux (ubuntu 12.10) . everything worked fine. it has blocked as expected . now the problem is i am also running an apache server for my LAN . ( kind of website ) but when accessing it via 192.168.0.1 , it says squid has blocked the connection , this is the exact error The following error was encountered while trying to retrieve the URL: http: //192.168.0.16/ Connection to 192.168.0.16 failed. The system returned: (113) No route to host The remote host or network may be down. Please try the request again. Your cache administrator is webmaster. before configuring the squid it was working fine . what changes in the squid.conf i have to make . i tried acl Safe_ports 80 allow_all Safe_ports ( i want to know how i can configure it again to listen HTTP request from LAN )

  Read the article

• Unable to connect my computer from LAN (http, smb) in UBUNTU 10.04

  - by Abdul Majeed

  I installed ubuntu 10.04, Apache, PHP, mysql, smb. Everything work fine in locally in my IP. When i trying to access my computer from LAN (other computer), it shows unable to connect. when i ping my IP from remote computer, its pinging OK. I can access internet, and all other systems (http, smb). But the problem is no one can't access my computer remotely in my LAN network. My ip is 192.168.85.105 and i want access(Appaceh,SMB) from 192.168.85.10. Is there any proxy firewall settings? I had tried following commands.. sudo iptables -F or sudo iptables-restore [logout require] If it does not work then try to disable net-filter sudo ufw --disable Please give me the solution.

  Read the article

• Route an IP from WAN to a host on LAN on OpenWRT

  - by Zsub

  EDIT: I know how to use NAT, I specifically want the server to be reachable on two IP's, one private, one public, with the firewall of the OpenWRT in between, if feasible. At the office we have recieved a /29 from our ISP. The first address is reserved for their endpoint, so I'm free to use five addresses. We run a local network, so of course there is a router in between running OpenWRT to provide all hosts with (W)LAN (dhcp from a private range). However, we also have a server running OS X Server 10.6 (Snow Leopard) and I'd like that server to be accessible both from the LAN using a private IP as well as from the WAN on it's own public IP. Point of note is that the server only has one network port, so multiple NICs is not an option, unfortunately. How would I go about doing this?

  Read the article

• Apache connection intermittantly times out on LAN

  - by jonescb

  I'm using Fedora 12 with Apache 2.2.14, and I was having this error on 2.2.13 as well. Even when I connect to my server over LAN, Firefox will occasionally time out while connecting. I can't figure out what is causing this. The error log isn't showing anything. I even cleaned the error log file, so that if something happened, it'd be a little easier to spot. But I'm still getting time outs, and nothing in the error log. Can anybody help me find what the problem is? Here is my httpd.conf Pastebin It's the default Fedora configuration; I've only changed the ServerName if I remember correctly. I'm pretty sure it's not the Timeout setting, because on LAN it should never time out. I don't believe it's a load issue either, I'm the only one connecting to it. I'm not an Apache expert, so if more information is needed I'll need some instructions on how to get that data.

  Read the article

• what Windowx XP LAN driver for Asus F5Z

  - by Radek

  a friend of mine asked me to re-install his Asus F5Z notebook with Windows XP. I installed succcessfully all drivers from assus driver download site. Everything is working fine but ethernet driver. The installation of Lan Driver for WIN XP finishes with strange message "Please shutdown & plug Realtech PCI-e card to complete the installation. Not sure if it matters but OnChip SATA is in 'Native IDE' mode . The original one with Vista was 'IDE - AHCI mode'. Any idea how I can make the LAN adapter to work under Windows XP?

  Read the article

• Best way to split LAN computers on two WANs (not load balancing)

  - by lpfavreau

  What is the best way to split the computers of a LAN (about 50 computers) to go on two WANs, depending on the computers' IP address or computers' configuration (gateway). I'm not looking for load-balancing, I need to be able to route which computer uses which Internet connection. A solution would be to rewire the old office to split the two distinct groups that need to use two different Internet connections but I'm not sure it's worth it at the moment. I have a pfSense router configured with the LAN (DHCP), WAN1 and WAN2. I also have the IP addresses (and ability to configure) the next router on WAN1 and the one on WAN2. What would you suggest? Routing based on IP addresses ranges? Different gateways? VLANs would be difficult for the same reason as to why rewire is a bit complicated. Thanks!

  Read the article

• Prevent machine in a LAN from receiving a remote shutdown

  - by WebDevHobo

  I'm probably just overreacting, but I recently came across a LAN-scanner that showed me the option "remote shutdown", for all found computers on the scanned network. Now, how exactly does this work? If I send such a message, will the shutdown happen no matter what, or is it required to have the password/user-name of the user of that other computer. Mostly I'm wondering: can this be done to me and how do I prevent it? EDIT: what's more, I had the scanner check for shares. The result being this: Double clicking the links opens them in explorer, basically meaning my entire C and F drive(only 2 HD's I have) are completely exposed to anyone in my LAN. Or can I open these because it's my own machine?

  Read the article

• Remote Desktop Services create LAN and WAN user groups

  - by PHLiGHT

  I'm setting up one server with the gateway, server host and web access roles on it. I know that isn't ideal but I don't expect to have many simulatenous users. I want users to access remote desktop web access and connect to the server host via the gateway as outlined here which avoids opening 3389 to the internet. Users will be connecting from the LAN and the WAN. What I'm looking to do is to allow some users LAN access but not WAN access and added plus would be if security settings (such as no clipboard) would be different when accessing via the WAN. Is this possible? It seems all users can logon to remote desktop web access by default. They can't run the remoteapps once logged in though without the proper permissions. Can I prevent them from even logging into remote web access? Since they renamed it from terminal services to remote desktop services it has made my Googling a bit harder. Thanks!

  Read the article

• Have OS X send wake on lan before printing to shared printer

  - by Dean Hill

  I have a MacBook that prints to a shared Windows 7 printer. Sometimes the Windows machine is asleep, and the Mac will just queue up its print requests. I recently created a script to send a wake-on-lan packet to a Windows 7 machine. This wakes up the Windows machine and printing starts. Great, but I think the system can be automated en Is it possible to have the MacBook run the wake-on-lan script everytime something is printed? Stated more generally, can I have the OS X print subsystem execute a script everytime something is printed?

  Read the article

• Cannot install wireless lan service on windows 2012 RTM offline

  - by user1763118

  I'm having trouble installing the wireless lan service offline with a fresh installed windows 2012 server RTM. I tried "install-windowsfeature wireless-networking" in the non-gui mode and using the server manager in the gui mode to enable the wireless lan service, but both of them show a "failure configuring windows updates" message after the installation restarted the system. I checked the event log and I think messages about "The WLAN Autoconfig service depends on the following service: nativewifip. This service might not be installed" are the source of the issue. Google shows it is a service called "native wifi filter", but I cannot find anywhere to install that service. I don't have a Ethernet adapter for that computer, so have to install everything offline before the wifi's working.

  Read the article

• VPN Connection Causes Internal LAN Connection Loss with Server

  - by sleepisfortheweak

  I've tried configuring basic PPTP VPN at my small business using a number of different tutorials. As far as I can tell, the actual VPN connection worked fine, but upon connecting a client, the Server 'disappears' from the internal LAN. The RRAS service must be stopped before the connection is restored. My Setup: The network is simply a DSL Gateway/Router to the outside functioning as NAT/Firewall/DHCP. The server is a Win Server 2008 machine at fixed IP 192.168.1.200. The server has 1 NIC, so I used the 'custom' option when configuring RRAS. The RRAS settings should be default except that I've disabled ports for connection types I'm not using and reduced PPTP ports to 10. I've also created an address pool and disabled DHCP packet forwarding. The server only functions as a File Share and now a VPN Server. Local LAN computers all have mapped network shares to the server authenticated based on Local User/Group setup on the server. The Problem: The moment a client connects through VPN, the server 'disappears' from the local network. All mapped drives disconnect and there is no response to a ping 192.168.1.200. Even if the client disconnects, the server does not re-appear at that address until the RRAS service is stopped. I've Tried: Using an Address Pool inside and outside the local subnet. Using DCHP Relay Checking Inbound/Outbound filters (none enabled) The fact that nothing I've tried has had any effect, and that I can connect and successfully obtain an IP tells me that it's something more fundamental I'm missing. My gut tells me that it's something to do with the second IP address added by the VPN client somehow taking over the interface or traffic from the local LAN accidently getting routed to the VPN client instead of handled at the server once RRAS has become 'active' when a client connects. Hopefully this may be obvious to someone with real IT experience. I've been doing this a while and almost never been stumped. I'm starting to think it might actually be something tricky since my setup is pretty basic yet refuses to work. I'll be happy to include more info if this doesn't ring any bells right away for anyone. Thanks

  Read the article

• Lan DNS not working after reinstall of Ubuntu 13.10

  - by DrorCohen

  I upgrade my Ubuntu desktop to 13.10. When I say upgrade I mean installed on a new partition from scratch (old partition is available if To the problem: I'm trying to ping a host (Drobo-FS server) by it's host name. I get "Unknown Host". However pinging from another computer on the same lan - works fine (a laptop with 12.04 lts). for that matter every ping from the 13.10 to the local lan by hostname fails, ping with ip works. I don't have a local DNS server but somehow all the other computers in the network find each other by host name - only this new one fails... help appreciated...

  Read the article

• Two routers in a LAN

  - by taxi

  router A no wifi +--- pc01 +--- pc02 | +--- router B wifi +--- pc03 +--- printer In my LAN I have a modem-router (say A) (no wifi connection) acting as DHCP server, and connected to the Internet. Now, I want to add another router (say B) (with wifi connection) to the LAN, in order to connect wifi pc's and net printers. Here I would disable DCHP server functionality. Is it correct to connect router B to router A via an ethernet port? In router A I define an IP address (eg 192.168.1.100) to be assigned to router B (MAC address). I expect to see router B listed as an attached device, in router A's status, but on the contrary it is not listed.

  Read the article

• How to shut down a computer having a particular IP address?

  - by iamrohitbanga

  If we have a collection of Windows and Linux computers on a LAN, is it possible to shutdown a computer having a specific IP address, using the Linux shell? Assume that I do not have ssh or telnet running on the PCs. I have the root password for all the computers.

  Read the article

• How to detect Router or Transmission line error.

  - by vaibhav

  I have a large LAN at my company. I suspect that there is a failure of a router or of a transmission line connecting routers. I want to narrow down the search, where is the fault. How could I narrow down the location of the problem.

  Read the article

• How does NetCut work ?

  - by Manish Mathai

  NetCut is a software which enables a network admin to turn off the internet connection of any machine in a LAN. I want to know how it works. It has something to do with spurious ARP packets, however can't seem to find exactly how it works. I am looking for a detailed answer. Any takers ?

  Read the article

• Uncheck Automatically detect proxy for Terminal Server users via GPO

  - by Chris

  Good morning, I have a registry key that changes local users Internet Explorer LAN Settings to uncheck the "Automatically detect settings" tickbox. When I add this policy to the Terminal Servers user group it has no effect. I exported this key from my own registry after unticking the box. My computer runs Windows Vista Business Edition. Environment: We are using Server 2008 RC2 environment - two terminal servers with a session broker. Any idea's on how to get this working?

  Read the article

• How to serve a webpage on connection to WiFi network

  - by samwatt

  Hi, I would like to be able to serve a local webpage (on a LAN) when someone connects to a WiFi network. This happens quite often in libraries, cafes etc, so i'm sure it can be done, but I have no idea how and can't seem to find much through searching the web. That, and my very limited networking knowledge means I'm hoping you guys can point me in the right direction. Many thanks!

  Read the article

• Cisco sg100-08 connections

  - by Terix

  I have multiple computers, some have a 10/100 ethernet adapter while others have a 10/100/1000 ones. If I connect them together with the Cisco sg100-08 switch, do I keep the 1Gbit speed where possible (between two devices at 1Gbit speed) or the whole lan slows down to 100mbit? I checked Cisco website but I couldn't find this kind of information, nor I was able to register to the Cisco support to ask this question (the registration form does not work)

  Read the article

• How to serve a webpage on connection to WiFi network

  - by samwatt

  Hi, I would like to be able to serve a local webpage (on a LAN) when someone connects to a WiFi network. This happens quite often in libraries, cafes etc, so i'm sure it can be done, but I have no idea how and can't seem to find much through searching the web. That, and my very limited networking knowledge means I'm hoping you guys can point me in the right direction. Many thanks!

  Read the article

• Obtaining Second WAN - Want to keep

  - by ndavis

  My business is growing so I've decided to purchase a second DSL line, to separate two departments to allow for more bandwidth usage. Previously I had a network printer that served both departments. With the addition of the second DSL line, I'm potentially going to have two separate LANs. How can I set it up so that the new LAN still has access to the Network Printer, but ensure that they are still using the new DSL line?

  Read the article

• Is there a way I can have my computer go to sleep but be able to wake it up remotely?

  - by joshcomley

  I've heard of Wake-Up-On-LAN (well, I've seen it in the BIOS) but I've never been 100% how to work it. Would this do what I'm after, and if not - would anything else? I'm using Windows 7, in case it matters..

  Read the article

• "Error 53" with local LAN machines after VPN session on server

  - by tim11g

  I have a Windows 2000 server with a Windows 7 client that occasionally gets "error 53" when accessing the server by name (net view \\server). It still works by IP address (net view \\192.168.0.1). The server's primary IP address (as shown in "routing and remote access" as "Gigabit Ethernet" is 192.168.0.1. There is also a secondary IP address shown as "Internal" which is 192.168.0.50 The server also supports VPN. When a VPN user connects, it gets an address in the range of 192.168.0.51 to .59. Normally (when there is no error), when the local LAN client runs "ping server", it resolves to 192.168.0.1. When the Error 53 problem happens, "ping server" resolves to 192.168.0.50. This problem seems to be related to when a user connects or has recently connected to the server VPN. Is there some connection between the VPN services on the server and the DNS services on the server that could cause a local LAN client to become confused about which IP address to use for the server? Or is there a misconfiguration in the VPN or DNS?

  Read the article

• Routing WIFI and LAN for specific traffic

  - by jakebird451

  I have two network devices aboard my macbook pro: WIFI (en1): Used for general traffic. Connects to an ip of 192.168.19.* via DHCP LAN (en0): Used for specific traffic. Connects to an ip of 192.168.2.10 as a static IP. Does not connect to a router, only a switch for direct routing connection. I have 4 IP addresses I need to access on the LAN: 192.168.2.1 192.168.2.21 192.168.2.20 192.168.2.30 The rest of the traffic needs to go to WIFI. I have tried setting up a routing table for the specific ip addresses, but I only managed to mess up my network. I do not venture out into the world of networking too often, but this was the latest command I have been trying: sudo route add -host 192.168.2.30 -interface en0 This command killed my ability to use ping. It told me that ping could not allocate memory (is that even possible)? It also killed my wifi access. Logging out and back in fixed the issue. I really do not mind to make this solution permanent, so I am fine with a temporary routing.

  Read the article

< Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >