Search Results

Search found 344 results on 14 pages for 'pinging'.

Page 13/14 | < Previous Page | 9 10 11 12 13 14  | Next Page >

• Can ping device from one computer and not the other

  - by Sean Duggan

  I've recently been assigned to work on a diagnostic program done in C++ which communicates with a piece of electronic equipment. Our normal scenario involves communicating via an RS232 interface, but I've been asked to make our program work over ethernet, source code having been done in Visual Basic. After much thrashing about trying to get the code to work and continuing to get 10049 Winsock errors when I tried to connect, I tried pinging the switch. From the computer the VB program is running on, I can see the switch via ping, nslookup, tracert, and pathping (I was going down the list of programs) and I can do this via URI or IP address. From my laptop, sending the same commands fails every time. They're both using the same network cable and the same USB-to-Ethernet device (I've been swapping them between tests) but one can see the switch and the other cannot. I'm working on the programming end, but the ping results makes me think that there might be a network issue stymieing me. wry grin I'm not much of a network guy, so I'm appealing to expert assistance. Both computers are running Windows XP if that helps. The connection is to an "IP-RS8" device which then connects to our VCU-C units. Each unit is accessible via URI or IP address on the desktop computer we usually have connected to the units (it's running the older VB program that I was asked to lift the networking code from). The connection is made via a USB-to-Ethernet adapter so as to leave the regular Ethernet port available for connecting to the company network. Hmm... come to think of it, I've probably been confusing the issue, talking about pinging "the switch" rather than indicating that it's the devices. My apologies. Communication is generally done with a DLL that uses Winsock functions to make queries for data from the VCU and then to receive. I'm failing when connecting. I haven't found anything on the firewall which should block these commands, but I'll keep poking. I don't know if it's potentially relevant, but on the desktop, the adapter maps to Local Area Connection 3 while on the laptop, it consistently maps to Local Area Connection 2. Currently reading up on DHCP. IPConfig /all results: Desktop Host Name . . . . . . . . . . . . : AMERDAEXXXXXX Primary Dns Suffix . . . . . . . : amer.example.com Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : COMPANY.com amer.example.com atle.example.com cone.example.com apac.example.com scan.example.com bYX.example.com Ethernet adapter Local Area Connection X: Connection-specific DNS Suffix . : amer.example.com Description . . . . . . . . . . . : Broadcom NetXtreme XYxx Gigabit Controller Physical Address. . . . . . . . . : YY-XX-YB-XX-XX-XX Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : XYY.XXX.XY.XXX Subnet Mask . . . . . . . . . . . : XXX.XXX.XXY.Y Default Gateway . . . . . . . . . : XYY.XXX.XY.X DHCP Server . . . . . . . . . . . : XY.XXX.XXY.XX DNS Servers . . . . . . . . . . . : XY.XXX.XXY.XX XY.XXY.XXY.XX Primary WINS Server . . . . . . . : XY.XXX.XXY.X Secondary WINS Server . . . . . . : XY.XXY.XXY.X Lease Obtained. . . . . . . . . . : Thursday, July XX, XYXX XY:XX:XX AM Lease Expires . . . . . . . . . . : Sunday, July XX, XYXX XY:XX:XX AM Ethernet adapter Local Area Connection X: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : ASIX axYYYYX USBX.Y to Fast Ethernet Adapter Physical Address. . . . . . . . . : YY-XY-BY-YX-XY-AY Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : XY.Y.Y.X Subnet Mask . . . . . . . . . . . : XXX.XXX.XXY.Y Default Gateway . . . . . . . . . : XY.Y.Y.X DHCP Server . . . . . . . . . . . : XY.Y.Y.XY DNS Servers . . . . . . . . . . . : XY.Y.Y.X Lease Obtained. . . . . . . . . . : Thursday, July XX, XYXX XY:XX:XY AM Lease Expires . . . . . . . . . . : Tuesday, August YX, XYXX XX:XY:XY AM Laptop Windows IP Configuration Host Name . . . . . . . . . . . . : AMERLAFYYXXYX Primary Dns Suffix . . . . . . . : amer.example.com Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : COMPANY.com amer.example.com atle.example.com cone.example.com apac.example.com scan.example.com bYX.example.com Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : amer.example.com Description . . . . . . . . . . . : Intel(R) 82567LM Gigabit Network Connection Physical Address. . . . . . . . . : YY-XY-BY-DY-XB-YX Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : XYY.XXX.XY.XY Subnet Mask . . . . . . . . . . . : XXX.XXX.XXY.Y Default Gateway . . . . . . . . . : XYY.XXX.XY.X DHCP Server . . . . . . . . . . . : XY.XXX.XXY.XX DNS Servers . . . . . . . . . . . : XY.XXX.XXY.XX XY.XXY.XXY.XX Primary WINS Server . . . . . . . : XY.XXX.XXY.X Secondary WINS Server . . . . . . : XY.XXY.XXY.X Lease Obtained. . . . . . . . . . : Thursday, July XX, XYXX XX:XX:XX AM Lease Expires . . . . . . . . . . : Sunday, July XX, XYXX XX:XX:XX AM Ethernet adapter {XYXAAYXX-YEDY-XXYX-YYEX-BYXYXXYEEYEX}: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Nortel IPSECSHM Adapter - Packet Scheduler iniport Physical Address. . . . . . . . . : XX-XX-XX-XX-XX-YY Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : Y.Y.Y.Y Subnet Mask . . . . . . . . . . . : Y.Y.Y.Y Default Gateway . . . . . . . . . : Ethernet adapter Leaf Networks Adapter: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Leaf Networks Adapter Physical Address. . . . . . . . . : YY-FF-FA-BC-YF-AY Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : X.XYY.XY.XX Subnet Mask . . . . . . . . . . . : XXX.Y.Y.Y Default Gateway . . . . . . . . . : Ethernet adapter Local Area Connection 3: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Bluetooth LAN Access Server Driver Physical Address. . . . . . . . . : YY-FX-AX-YA-BY-CA Ethernet adapter Wireless Network Connection 2: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Intel(R) WiFi Link 5300 AGN Physical Address. . . . . . . . . : YY-XX-YA-CX-FC-YE Ethernet adapter Local Area Connection 2: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : ASIX ax88772 USB2.0 to Fast Ethernet Adapter Physical Address. . . . . . . . . : YY-XY-BY-YX-XY-AY Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : XYX.XYY.X.X Subnet Mask . . . . . . . . . . . : XXX.XXX.XXX.Y Default Gateway . . . . . . . . . :

  Read the article

• getting autodiscover URL from Exchange email address

  - by Anthony

  I'm starting with an address for an Exchange 2007 server: [email protected] And I attempted to send an autodiscover request, as documented at MSDN. I attempted to use the generic autodiscover address documented at the TechNet White Paper. So, using curl on PHP, I sent the following request: <Autodiscover xmlns="http://schemas.microsoft.com/exchange/autodiscover/outlook/requestschema/2006"> <Request> <EMailAddress>[email protected]</EMailAddress> <AcceptableResponseSchema> http://schemas.microsoft.com/exchange/autodiscover/outlook/responseschema/2006a </AcceptableResponseSchema> </Request> </Autodiscover> to the following URL: https://domain.exchangeserver.org/autodiscover/autodiscover.xml But got no response, just an eventual timeout. I also tried: https://autodiscover.domain.exchangeserver.org/autodiscover/autodiscover.xml With the same result. Now, since my larger goal is to use Autodiscover with Exchange Web Services, and since all of the EWS URLs start with the same sub-domain as the Outlook Web Access address, I thought I'd give that a try: OWA: https://wmail.domain.exchangeserver.org So I tried: https://wmail.domain.exchangeserver.org/autodiscover/autodiscover.xml And sure enough, I got back the expected response. However, I only knew the OWA sub-domain because it's the server I have access to and that I'm using to test everything. I would not know it for sure or be able to guess it if this were a live app and the user was entering in their own Exchange email. I know that whatever generic autodiscover settings must be turned on, because I can enter: [email protected] into Apple Mail on Snow Leopard and it finds everything without trouble. So the question is... Should https://domain.exchangeserver.org/autodiscover/autodiscover.xml have worked, and I just missed a step when trying to connect to it? Or, Is there some trick (maybe involving pinging the email address?) that Apple Mail and other clients use to resolve the address to the OWA subdomain before sending the autodiscover request? Thanks to anyone who knows or can take a wild guess.

  Read the article

• Ping remote server and wait to get data

  - by infinity

  Hi I'm building my first application for android and I've reached a point where I can't find a solution even have no idea what to search for in Google. So the problem: I am pinging a remote server with GET request through the application passing some parameters like file_id. Then the server gives back confirmation if the file exists or error otherwise, both in plain text. The error string is $$$ERROR$$$. Actually the confirmation is JSON string that holds the path to the file. If the file doesn't exists on the server it generated the error message and start downloading the file and processing it which normally takes 10-30 seconds. What would be the best way to check if the file is ready for download? I have DownloadFile class that extends AsyncTask but before I reach the point to download the file I need the URL which is dependant on the previous request which is in the main class in the UI thread. Here is some code: public class MainActivity extends Activity { private String getInfo() { // Create a new HttpClient and Post Header HttpClient httpClient = new DefaultHttpClient(); HttpGet httpPost = new HttpGet(infoUrl); StringBuilder sb = null; String data; JSONObject jObject = null; try { HttpResponse response = httpClient.execute(httpPost); // This might be equal "$$$ERROR$$$" if no file exists sb = inputStreamToString(response.getEntity().getContent()); } catch(ClientProtocolException e) { // TODO Auto-generated catch block Log.v("Error: pushItem ClientProtocolException: ", e.toString()); } catch (IOException e) { // TODO Auto-generated catch block Log.v("Error: pushItem IOException: ", e.toString()); } // Clean the data to be complaint JSON format data = sb.toString().replace("info = ", ""); try { jObject = new JSONObject(data); data = jObject.getString("h"); fileTitle = jObject.getString("title"); } catch (JSONException e) { // TODO Auto-generated catch block e.printStackTrace(); } downloadUrl = String.format(downloadUrl, fileId, data); return downloadUrl; } } So my idea was to get the content and if equal to $$$ERROR$$$ go into loop until JSON data is passed but I guess there is better solution. Note: I don't have control over the server output so have to deal with what I have.

  Read the article

• When may I ask a question to fellow developers? (Rules before asking questions).

  - by Zwei Steinen

  I assigned a quite simple task to one junior developer today, and he kept pinging me EVERY 5 minutes for HOURS, asking STEP BY STEP, what to do. Whenever something went wrong, he simply copy&pasted the log and basically wrote, "An exception occurred. What should I do?" So I finally had to tell him, "If you want to be a developer, please start thinking a little bit. Read the error message. That's what they are for!". I also however, tell junior developers to ask questions before spending too much time trying to solve it themselves. This might sound contradictory, but I feel there is some kind of an implicit rule that distinguishes questions that should be asked fairly quickly and that should not (and I try to follow those rules when I ask questions..) So my question is, do you have any rules that you follow, or expect others to follow on asking questions? If so, what are they? Let me start with my own. If you have struggled for more than 90 min, you may ask that question (exceptions exists). If you haven't struggled for more than 15 min, you may not ask that question (if you are sure that the answer can not be found within 15 min, this rule does not have to apply). If it is completely out of your domain and you do not plan to learn that domain, you may ask that question after 15 min (e.g. if I am a java programmer and need to back up the DB, I may ask the DBA what procedure to follow after googling for 15 min). If it is a "local" question, whose answer is difficult to derive or for which resources is difficult to get (e.g. asking an colleague "what method xxx does" etc.), you may ask that question after 15 min. If the answer for it is difficult to derive, and you know that the other person knows the answer, you may ask the question after 15 min (e.g. asking a hibernate expert "What do I need to change else to make this work?". If the process to derive the answer is interesting and is a good learning opportunity, you may ask for hints but you may not ask for answers! What are your rules?

  Read the article

• iptable CLUSTERIP won't work

  - by Rad Akefirad

  We have some requirements which explained here. We tried to satisfy them without any success as described. Here is the brief information: Here are requirements: 1. High Availability 2. Load Balancing Current Configuration: Server #1: one static (real) IP for each 10.17.243.11 Server #2: one static (real) IP for each 10.17.243.12 Cluster (virtual and shared among all servers) IP: 10.17.243.15 I tried to use CLUSTERIP to have the cluster IP by the following: on the server #1 iptables -I INPUT -i eth0 -d 10.17.243.15 -j CLUSTERIP --new --hashmode sourceip --clustermac 01:00:5E:00:00:20 --total-nodes 2 --local-node 1 on the server #2 iptables -I INPUT -i eth0 -d 10.17.243.15 -j CLUSTERIP --new --hashmode sourceip --clustermac 01:00:5E:00:00:20 --total-nodes 2 --local-node 2 When we try to ping 10.17.243.15 there is no reply. And the web service (tomcat on port 8080) is not accessible either. However we managed to get the packets on both servers by using TCPDUMP. Some useful information: iptable roules (iptables -L -n -v): Chain INPUT (policy ACCEPT 21775 packets, 1470K bytes) pkts bytes target prot opt in out source destination 0 0 CLUSTERIP all -- eth0 * 0.0.0.0/0 10.17.243.15 CLUSTERIP hashmode=sourceip clustermac=01:00:5E:00:00:20 total_nodes=2 local_node=1 hash_init=0 Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 14078 packets, 44M bytes) pkts bytes target prot opt in out source destination Log messages: ... kernel: [ 7.329017] e1000e: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None ... kernel: [ 7.329133] e1000e 0000:05:00.0: eth3: 10/100 speed: disabling TSO ... kernel: [ 7.329567] ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready ... kernel: [ 71.333285] ip_tables: (C) 2000-2006 Netfilter Core Team ... kernel: [ 71.341804] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) ... kernel: [ 71.343168] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully ... kernel: [ 108.456043] device eth0 entered promiscuous mode ... kernel: [ 112.678859] device eth0 left promiscuous mode ... kernel: [ 117.916050] device eth0 entered promiscuous mode ... kernel: [ 140.168848] device eth0 left promiscuous mode TCPDUMP while pinging: tcpdump: listening on eth0, link-type EN10MB (Ethernet), capture size 65535 bytes 12:11:55.335528 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto ICMP (1), length 84) 10.17.243.1 > 10.17.243.15: ICMP echo request, id 16162, seq 2390, length 64 12:11:56.335778 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto ICMP (1), length 84) 10.17.243.1 > 10.17.243.15: ICMP echo request, id 16162, seq 2391, length 64 12:11:57.336010 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto ICMP (1), length 84) 10.17.243.1 > 10.17.243.15: ICMP echo request, id 16162, seq 2392, length 64 12:11:58.336287 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto ICMP (1), length 84) 10.17.243.1 > 10.17.243.15: ICMP echo request, id 16162, seq 2393, length 64 And there is no ping reply as I said. Does anyone know which part I missed? Thanks in advance.

  Read the article

• How to prevent delays associated with IPv6 AAAA records?

  - by Nic

  Our Windows servers are registering IPv6 AAAA records with our Windows DNS servers. However, we don't have IPv6 routing enabled on our network, so this frequently causes stall behaviours. Microsoft RDP is the worst offender. When connecting to a server that has a AAAA record in DNS, the remote desktop client will try IPv6 first, and won't fall back to IPv4 until the connection times out. Power users can work around this by connecting to the IP address directly. Resolving the IPv4 address with ping -4 hostname.foo always works instantly. What can I do to avoid this delay? Disable IPv6 on client? Nope, Microsoft says IPv6 is a mandatory part of the Windows operating system. Too many clients to ensure this is set everywhere consistently. Will cause more problems later when we finally implement IPv6. Disable IPv6 on the server? Nope, Microsoft says IPv6 is a mandatory part of the Windows operating system. Requires an inconvenient registry hack to disable the entire IPv6 stack. Ensuring this is correctly set on all servers is inconvenient. Will cause more problems later when we finally implement IPv6. Mask IPv6 records on the user-facnig DNS recursor? Nope, we're using NLNet Unbound and it doesn't support that. Prevent registration of IPv6 AAAA records on the Microsoft DNS server? I don't think that's even possible. At this point, I'm considering writing a script that purges all AAAA records from our DNS zones. Please, help me find a better way. UPDATE: DNS resolution is not the problem. As @joeqwerty points out in his answer, the DNS records are returned instantly. Both A and AAAA records are immediately available. The problem is that some clients (mstsc.exe) will preferentially attempt a connection over IPv6, and take a while to fall back to IPv4. This seems like a routing problem. The ping command produces a "General failure" error message because the destination address is unroutable. C:\Windows\system32>ping myhost.mydomain Pinging myhost.mydomain [2002:1234:1234::1234:1234] with 32 bytes of data: General failure. General failure. General failure. General failure. Ping statistics for 2002:1234:1234::1234:1234: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), I can't get a packet capture of this behaviour. Running this (failing) ping command does not produce any packets in Microsoft Network Monitor. Similarly, attempting a connection with mstsc.exe to a host with an AAAA record produces no traffic until it does a fallback to IPv4. UPDATE: Our hosts are all using publicly-routable IPv4 addresses. I think this problem might come down to a broken 6to4 configuration. 6to4 behaves differently on hosts with public IP addresses vs RFC1918 addresses. UPDATE: There is definitely something fishy with 6to4 on my network. When I disable 6to4 on the Windows client, connections resolve instantly. netsh int ipv6 6to4 set state disabled But as @joeqwerty says, this only masks the problem. I'm still trying to find out why IPv6 communication on our network is completely non-working.

  Read the article

• Troubleshooting unwanted NTP Traffic

  - by Jaxaeon

  A domain controller running Windows Server 2012 is sending NTP and NETBIOS traffic to an address that has never been configured as a time provider. The server logs give no indication that any NTP traffic is failing. The only place I see any evidence of this traffic is in pfSense system logs: (Blocked) Jun 9 08:48:50 DOMAIN 10.0.1.100:123 192.128.127.254:123 UDP (Blocked) Jun 9 08:48:53 DOMAIN 10.0.1.100:137 192.128.127.254:137 UDP As far as I can tell the NTP service is working normally otherwise: DC2.domain.com[10.0.1.101:123]: ICMP: 0ms delay NTP: -0.0131705s offset from DC1.domain.com RefID: DC1.domain.com [10.0.1.100] Stratum: 3 DC1.domain.com *** PDC ***[10.0.1.100:123]: ICMP: 0ms delay NTP: +0.0000000s offset from DC1.domain.com RefID: clock1.albyny.inoc.net [64.246.132.14] Stratum: 2 The time provider NtpClient is currently receiving valid time data from 1.pool.ntp.org,0×1 (ntp.m|0x0|0.0.0.0:123->204.2.134.163:123). The time provider NtpClient is currently receiving valid time data from 0.pool.ntp.org,0×1 (ntp.m|0x0|0.0.0.0:123->64.246.132.14:123). The time service is now synchronizing the system time with the time source 0.pool.ntp.org,0×1 (ntp.m|0x0|0.0.0.0:123->64.246.132.14:123). I've been inside and out of the NTP configuration and cannot find any reason for this traffic. Reverse DNS points the destination address to nothing.attdns.com. pinging nothing.attdns.com from the domain controller in question leads to a response from loopback (127.0.0.2) which makes my head hurt. Any ideas? EDIT1: It should probably be noted that after a dns flush, nslookup 192.128.127.254 returns nothing.attdns.com. 192.128.127.254 is not present in domain.com DNS records. The attdns.com domain is not present in cached lookups. 127.in-addr.arpa is clean of any funkyness. EDIT2: The loopback ping response from nothing.attdns.com is possibly unrelated. Machines on other networks are also displaying this behavior. EDIT3: As mentioned in the comments, I tracked the problem network adapter back to my pfSense VM hosted in esxi 5.5 (I know shame on me for virtualizing a firewall). pfSense was configured to use DC1.domain.com as its primary time provider, but upon changing it back to pool.ntp.org the problem persists. pfSense logs give no indication of NTP misconfiguration. Everywhere I can think to look this VM is identified as 10.0.1.253, so I still have no idea why it’s sending NTP requests as 192.128… Since this firewall was a temporary solution to a problem that no longer exists so I am going to decommission it. EDIT4: The queries were coming from another machine sharing the same virtual adapter as the firewall. The machine has two local adapters: one for LAN, and the other for attached hardware that uses an Ethernet connection. That hardware sits in the the mystery subnet, and the machine is broadcasting NTP requests over both adapters.

  Read the article

• bind9 DNS Ubuntu names pingible on server, but not on Windows Machines?

  - by leeand00

  I setup a DNS server today on Ubuntu, following this tutorial. My intent was to setup my network for dns-name resolving on the private LAN within a single zone (nothing fancy I just want name resolution). I've tested the setup on the DNS server machine itself, and I can ping all the machines listed in the configuration file. I've also configured the Windows Machines on my network, and for some reason they are incapable of pinging by names as was possible on the DNS Server itself. I've tried running nslookup on the Windows DNS clients and I receive and error mentioning the address of the DNS server. DNS forwarding works fine, I'm not having any trouble accessing the internet, the problem only lies within accessing names within the private LAN. Here are my configuration files: options { directory "/var/cache/bind"; // If there is a firewall between you and nameservers you want // to talk to, you may need to fix the firewall to allow multiple // ports to talk. See http://www.kb.cert.org/vuls/id/800113 // If your ISP provided one or more IP addresses for stable // nameservers, you probably want to use them as forwarders. // Uncomment the following block, and insert the addresses replacing // the all-0's placeholder. // forwarders { // 0.0.0.0; // }; forwarders { 8.8.8.8; 8.8.8.4; 74.242.0.12; //68.87.76.178; }; auth-nxdomain no; # conform to RFC1035 listen-on-v6 { any; }; }; /etc/bind/named.conf.options zone "leerdomain.local" { type master; file "/etc/bind/zones/leerdomain.local.db"; notify no; }; zone "2.168.192.in-addr.arpa" { type master; file "/etc/bind/zones/rev.2.168.192.in-addr.arpa"; notify no; }; /etc/bind/named.conf.local Lookup: $TTL 3D @ IN SOA ns.leerdomain.local. admin.leerdomain.local. ( 2010011001 28800 3600 604800 38400 ); leerdomain.local. IN NS ns.leerdomain.local. ns IN A 192.168.2.9 asus IN A 192.168.2.254 www IN CNAME asus vaio IN A 192.168.2.253 iptouch IN A 192.168.2.252 toshiba IN A 192.168.2.251 gw IN A 192.168.2.1 TXT "Network Gateway" /etc/bind/zones/leerdomain.local.db (Validates fine with named-checkzone when validating zone leerdomain.local) Reverse Lookup: $TTL 3D @ IN SOA ns.leerdomain.local. admin.leerdomain.local. ( 201001101 28800 604800 604800 86400 ) IN NS ns.leerdomain.local. 1 IN PTR gw.leerdomain.local. 254 IN PTR asus.leerdomain.local. 253 IN PTR vaio.leerdomain.local. 252 IN PTR iptouch.leerdomain.local. 251 IN PTR toshiba.leerdomain.local. /etc/bind/zones/rev.2.168.192.in-addr.arpa *(Does not validate with named-checkzone when validating zone leerdomain.local gives an error of: zone leerdomain.local/IN: NS 'ns.leerdomain.local' has no address records (A or AAAA) zone leerdomain.local/IN: not loaded due to errors. * Despite not validating bind9 starts without errors in /var/log/syslog I've also configured a few of the windows machines on my network to have the static ip as specified in the lookup and reverse lookup config files. i.e. Using nslookup yields the following results: C:\Users\leeand00>nslookup ns Server: UnKnown Address: 192.168.2.9 *** UnKnown can't find ns: Non-existent domain C:\Users\leeand00>nslookup gw Server: UnKnown Address: 192.168.2.9 Name: gw. Additionally trying to ping by name also fails on machines that are not the DNS Server. Is there something wrong with my configuration of either the nameserver or the Windows Boxes that is keeping me from accessing other machines using names?

  Read the article

• dns server bind is not work

  - by milad

  I just installed bind on RHEL 6 and point a domain to that server. but actually when i ping domain it returns error 1214: Here is my named.conf: // // named.conf // // Provided by Red Hat bind package to configure the ISC BIND named(8) DNS // server as a caching only nameserver (as a localhost DNS resolver only). // // See /usr/share/doc/bind*/sample/ for example named configuration files. // options { listen-on port 53 { any; }; listen-on-v6 port 53 { ::1; }; directory "/var/named"; dump-file "/var/named/data/cache_dump.db"; statistics-file "/var/named/data/named_stats.txt"; memstatistics-file "/var/named/data/named_mem_stats.txt"; allow-query { any; }; recursion yes; dnssec-enable yes; dnssec-validation yes; dnssec-lookaside auto; /* Path to ISC DLV key */ bindkeys-file "/etc/named.iscdlv.key"; managed-keys-directory "/var/named/dynamic"; }; logging { channel default_debug { file "data/named.run"; severity dynamic; }; }; zone "." IN { type hint; file "named.ca"; }; include "/etc/named.rfc1912.zones"; include "/etc/named.root.key"; zone "mydomain.com"{ type master; file "/var/named/data/named.mydomain.com"; allow-update { none; }; };` AND The content of "/var/named/data/named.mydomain.com": $TTL 38400 mydomain.com. IN SOA ns1.mydomain.com. milad.yahoo.com. ( 2012101201 ; serial number YYMMDDNN 28800 ; Refresh 7200 ; Retry 864000 ; Expire 38400 ; Min TTL ) mydomain.com. IN A 1.2.3.4 www IN A 1.2.3.4 ns1.mydomain.com. IN A 1.2.3.4 ns2.mydomain.com. IN A 1.2.3.4 mydomain.com. IN NS ns1.mydomain.com. mydomain.com. IN NS ns2.mydomain.com. AND i'm sure the named service is running: [root@server ~]# service named status version: 9.8.2rc1-RedHat-9.8.2-0.10.rc1.el6_3.3 CPUs found: 8 worker threads: 8 number of zones: 20 debug level: 0 xfers running: 0 xfers deferred: 0 soa queries in progress: 0 query logging is OFF recursive clients: 0/0/1000 tcp clients: 0/100 server is up and running named (pid 26299) is running... Thanks for your answers. i know that the ping is not the job of bind, i use it just to check whether domain is pointed to host or not.(ping is open in my server as i got reply in pinging ip) i use network-tools.com to ping domain. here the output of dig utility: dig mydomain.com ; <<>> DiG 9.8.2rc1-RedHat-9.8.2-0.10.rc1.el6_3.3 <<>> mydomain.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: SERVFAIL, id: 6806 ;; flags: qr rd ra; QUERY: 1, ANSWER: 0, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;mydomain.com. IN A ;; Query time: 321 msec ;; SERVER: 5.6.7.8#53(5.6.7.8)##note that 5.6.7.8 is my idc dns ip ;; WHEN: Sun Oct 14 23:53:47 2012

  Read the article

• An error occured synchronizing windows with time.windows.com

  - by Killrawr

  Okay so I've tried stopping/registering the win32tm service on this Windows Server 2008 Enterprise Computer. C:\Users\Administrator>net stop w32time The Windows Time service is stopping. The Windows Time service was stopped successfully. C:\Users\Administrator>w32tm /unregister The following error occurred: Access is denied. (0x80070005) C:\Users\Administrator>w32tm /unregister W32Time successfully unregistered. C:\Users\Administrator>w32tm /register W32Time successfully registered. C:\Users\Administrator>net start w32time The Windows Time service is starting. The Windows Time service was started successfully. (Source : http://social.technet.microsoft.com/Forums/en-US/winserverDS/thread/9bdfc2cc-4775-4435-8868-57d214e1e3ba/) And I get this error from the Date and Time, Internet Time tab (After also following the steps here). I've even tried the Atomic Time Clock Worldtimeserver and I get the error The following error occurred: The specified module could not be found. (0x8007007E). I've also disabled the Windows Firewall, that might of been blocking the synchronization. I've done a file scan with sfc /scannow that came back with no errors. C:\Users\Administrator>sfc /scannow Beginning system scan. This process will take some time. Beginning verification phase of system scan. Verification 100% complete. Windows Resource Protection did not find any integrity violations. C:\Users\Administrator> But I'm not having much luck. Is there anyway lo possibly solve this? or is the time.windows.com servers unsupported? because the software is from 2008? (I really don't know :/), My ping result to time.windows.com C:\Users\Administrator>ping time.windows.com Pinging time.microsoft.akadns.net [65.55.21.22] with 32 bytes of data: Request timed out. Request timed out. Request timed out. Request timed out. Ping statistics for 65.55.21.22: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), And tracert result C:\Users\Administratortracert time.windows.com Tracing route to time.microsoft.akadns.net [65.55.21.24] over a maximum of 30 hops: 1 1 ms <1 ms <1 ms 192.168.1.1 2 32 ms 31 ms 32 ms be2-100.bras1wtc.wlg.vf.net.nz [203.109.129.113] 3 31 ms 32 ms 31 ms be5-100.ppnzwtc01.wlg.vf.net.nz.129.109.203.in-a ddr.arpa [203.109.129.114] 4 31 ms 31 ms 31 ms gi0-2-0-3.ppnzwtc01.wlg.vf.net.nz.180.109.203.in -addr.arpa [203.109.180.210] 5 31 ms 31 ms 30 ms gi0-2-0-3.ppnzwtc02.wlg.vf.net.nz [203.109.180.2 09] 6 167 ms 166 ms 166 ms ip-141.199.31.114.VOCUS.net.au [114.31.199.141] 7 175 ms 175 ms 175 ms microsoft.com.any2ix.coresite.com [206.223.143.1 43] 8 177 ms 180 ms 176 ms xe-7-0-2-0.by2-96c-1a.ntwk.msn.net [207.46.42.17 6] 9 205 ms 205 ms 204 ms xe-10-0-2-0.co1-96c-1b.ntwk.msn.net [207.46.45.3 1] 10 * * * Request timed out. 11 * * * Request timed out. 12 * * * Request timed out. 13 * * * Request timed out. 14 * * * Request timed out. 15 * * * Request timed out. 16 ^C And nslookup C:\Users\Administrator>nslookup time.windows.com Server: UnKnown Address: 192.168.1.1 Non-authoritative answer: Name: time.microsoft.akadns.net Address: 65.55.21.22 Aliases: time.windows.com

  Read the article

• Monitoring Html Element CSS Changes in JavaScript

  - by Rick Strahl

  [ updated Feb 15, 2011: Added event unbinding to avoid unintended recursion ] Here's a scenario I've run into on a few occasions: I need to be able to monitor certain CSS properties on an HTML element and know when that CSS element changes. For example, I have a some HTML element behavior plugins like a drop shadow that attaches to any HTML element, but I then need to be able to automatically keep the shadow in sync with the window if the  element dragged around the window or moved via code. Unfortunately there's no move event for HTML elements so you can't tell when it's location changes. So I've been looking around for some way to keep track of the element and a specific CSS property, but no luck. I suspect there's nothing native to do this so the only way I could think of is to use a timer and poll rather frequently for the property. I ended up with a generic jQuery plugin that looks like this: (function($){ $.fn.watch = function (props, func, interval, id) { /// <summary> /// Allows you to monitor changes in a specific /// CSS property of an element by polling the value. /// when the value changes a function is called. /// The function called is called in the context /// of the selected element (ie. this) /// </summary> /// <param name="prop" type="String">CSS Properties to watch sep. by commas</param> /// <param name="func" type="Function"> /// Function called when the value has changed. /// </param> /// <param name="interval" type="Number"> /// Optional interval for browsers that don't support DOMAttrModified or propertychange events. /// Determines the interval used for setInterval calls. /// </param> /// <param name="id" type="String">A unique ID that identifies this watch instance on this element</param> /// <returns type="jQuery" /> if (!interval) interval = 200; if (!id) id = "_watcher"; return this.each(function () { var _t = this; var el$ = $(this); var fnc = function () { __watcher.call(_t, id) }; var itId = null; var data = { id: id, props: props.split(","), func: func, vals: [props.split(",").length], fnc: fnc, origProps: props, interval: interval }; $.each(data.props, function (i) { data.vals[i] = el$.css(data.props[i]); }); el$.data(id, data); hookChange(el$, id, data.fnc); }); function hookChange(el$, id, fnc) { el$.each(function () { var el = $(this); if (typeof (el.get(0).onpropertychange) == "object") el.bind("propertychange." + id, fnc); else if ($.browser.mozilla) el.bind("DOMAttrModified." + id, fnc); else itId = setInterval(fnc, interval); }); } function __watcher(id) { var el$ = $(this); var w = el$.data(id); if (!w) return; var _t = this; if (!w.func) return; // must unbind or else unwanted recursion may occur el$.unwatch(id); var changed = false; var i = 0; for (i; i < w.props.length; i++) { var newVal = el$.css(w.props[i]); if (w.vals[i] != newVal) { w.vals[i] = newVal; changed = true; break; } } if (changed) w.func.call(_t, w, i); // rebind event hookChange(el$, id, w.fnc); } } $.fn.unwatch = function (id) { this.each(function () { var el = $(this); var fnc = el.data(id).fnc; try { if (typeof (this.onpropertychange) == "object") el.unbind("propertychange." + id, fnc); else if ($.browser.mozilla) el.unbind("DOMAttrModified." + id, fnc); else clearInterval(id); } // ignore if element was already unbound catch (e) { } }); return this; } })(jQuery); With this I can now monitor movement by monitoring say the top CSS property of the element. The following code creates a box and uses the draggable (jquery.ui) plugin and a couple of custom plugins that center and create a shadow. Here's how I can set this up with the watcher: $("#box") .draggable() .centerInClient() .shadow() .watch("top", function() { $(this).shadow(); },70,"_shadow"); ... $("#box") .unwatch("_shadow") .shadow("remove"); This code basically sets up the window to be draggable and initially centered and then a shadow is added. The .watch() call then assigns a CSS property to monitor (top in this case) and a function to call in response. The component now sets up a setInterval call and keeps on pinging this property every time. When the top value changes the supplied function is called. While this works and I can now drag my window around with the shadow following suit it's not perfect by a long shot. The shadow move is delayed and so drags behind the window, but using a higher timer value is not appropriate either as the UI starts getting jumpy if the timer's set with too small of an increment. This sort of monitor can be useful for other things as well where operations are maybe not quite as time critical as a UI operation taking place. Can anybody see a better a better way of capturing movement of an element on the page?© Rick Strahl, West Wind Technologies, 2005-2011Posted in ASP.NET  JavaScript  jQuery  

  Read the article

• Developing Mobile Applications: Web, Native, or Hybrid?

  - by Michelle Kimihira

  Authors: Joe Huang, Senior Principal Product Manager, Oracle Mobile Application Development Framework  and Carlos Chang, Senior Principal Product Director The proliferation of mobile devices and platforms represents a game-changing technology shift on a number of levels. Companies must decide not only the best strategic use of mobile platforms, but also how to most efficiently implement them. Inevitably, this conversation devolves to the developers, who face the task of developing and supporting mobile applications—not a simple task in light of the number of devices and platforms. Essentially, developers can choose from the following three different application approaches, each with its own set of pros and cons. Native Applications: This refers to apps built for and installed on a specific platform, such as iOS or Android, using a platform-specific software development kit (SDK).  For example, apps for Apple’s iPhone and iPad are designed to run specifically on iOS and are written in Xcode/Objective-C. Android has its own variation of Java, Windows uses C#, and so on.  Native apps written for one platform cannot be deployed on another. Native apps offer fast performance and access to native-device services but require additional resources to develop and maintain each platform, which can be expensive and time consuming. Mobile Web Applications: Unlike native apps, mobile web apps are not installed on the device; rather, they are accessed via a Web browser.  These are server-side applications that render HTML, typically adjusting the design depending on the type of device making the request.  There are no program coding constraints for writing server-side apps—they can be written in Java, C, PHP, etc., it doesn’t matter.  Instead, the server detects what type of mobile browser is pinging the server and adjusts accordingly. For example, it can deliver fully JavaScript and CSS-enabled content to smartphone browsers, while downgrading gracefully to basic HTML for feature phone browsers. Mobile apps work across platforms, but are limited to what you can do through a browser and require Internet connectivity. For certain types of applications, these constraints may not be an issue. Oracle supports mobile web applications via ADF Faces (for tablets) and ADF Mobile browser (Trinidad) for smartphone and feature phones. Hybrid Applications: As the name implies, hybrid apps combine technologies from native and mobile Web apps to gain the benefits each. For example, these apps are installed on a device, like their pure native app counterparts, while the user interface (UI) is based on HTML5.  This UI runs locally within the native container, which usually leverages the device’s browser engine.  The advantage of using HTML5 is a consistent, cross-platform UI that works well on most devices.  Combining this with the native container, which is installed on-device, provides mobile users with access to local device services, such as camera, GPS, and local device storage.  Native apps may offer greater flexibility in integrating with device native services.  However, since hybrid applications already provide device integrations that typical enterprise applications need, this is typically less of an issue.  The new Oracle ADF Mobile release is an HTML5 and Java hybrid framework that targets mobile app development to iOS and Android from one code base. So, Which is the Best Approach? The short answer is – the best choice depends on the type of application you are developing.  For instance, animation-intensive apps such as games would favor native apps, while hybrid applications may be better suited for enterprise mobile apps because they provide multi-platform support. Just for starters, the following issues must be considered when choosing a development path. Application Complexity: How complex is the application? A quick app that accesses a database or Web service for some data to display?  You can keep it simple, and a mobile Web app may suffice. However, for a mobile/field worker type of applications that supports mission critical functionality, hybrid or native applications are typically needed. Richness of User Interactivity: What type of user experience is required for the application?  Mobile browser-based app that’s optimized for mobile UI may suffice for quick lookup or productivity type of applications.  However, hybrid/native application would typically be required to deliver highly interactive user experiences needed for field-worker type of applications.  For example, interactive BI charts/graphs, maps, voice/email integration, etc.  In the most extreme case like gaming applications, native applications may be necessary to deliver the highly animated and graphically intensive user experience. Performance: What type of performance is required by the application functionality?  For instance, for real-time look up of data over the network, mobile app performance depends on network latency and server infrastructure capabilities.  If consistent performance is required, data would typically need to be cached, which is supported on hybrid or native applications only. Connectivity and Availability: What sort of connectivity will your application require? Does the app require Web access all the time in order to always retrieve the latest data from the server? Or do the requirements dictate offline support? While native and hybrid apps can be built to operate offline, Web mobile apps require Web connectivity. Multi-platform Requirements: The terms “consumerization of IT” and BYOD (bring your own device) effectively mean that the line between the consumer and the enterprise devices have become blurred. Employees are bringing their personal mobile devices to work and are often expecting that they work in the corporate network and access back-office applications.  Even if companies restrict access to the big dogs: (iPad, iPhone, Android phones and tablets, possibly Windows Phone and tablets), trying to support each platform natively will require increasing resources and domain expertise with each new language/platform. And let’s not forget the maintenance costs, involved in upgrading new versions of each platform.   Where multi-platform support is needed, Web mobile or hybrid apps probably have the advantage. Going native, and trying to support multiple operating systems may be cost prohibitive with existing resources and developer skills. Device-Services Access:  If your app needs to access local device services, such as the camera, contacts app, accelerometer, etc., then your choices are limited to native or hybrid applications.   Fragmentation: Apple controls Apple iOS and the only concern is what version iOS is running on any given device.   Not so Android, which is open source. There are many, many versions and variants of Android running on different devices, which can be a nightmare for app developers trying to support different devices running different flavors of Android.  (Is it an Amazon Kindle Fire? a Samsung Galaxy?  A Barnes & Noble Nook?) This is a nightmare scenario for native apps—on the other hand, a mobile Web or hybrid app, when properly designed, can shield you from these complexities because they are based on common frameworks.  Resources: How many developers can you dedicate to building and supporting mobile application development?  What are their existing skills sets?  If you’re considering native application development due to the complexity of the application under development, factor the costs of becoming proficient on a each platform’s OS and programming language. Add another platform, and that’s another language, another SDK. On the other side of the equation, Web mobile or hybrid applications are simpler to make, and readily support more platforms, but there may be performance trade-offs. Conclusion This only scratches the surface. However, I hope to have suggested some food for thought in choosing your mobile development strategy.  Do your due diligence, search the Web, read up on mobile, talk to peers, attend events. The development team at Oracle is working hard on mobile technologies to help customers extend enterprise applications to mobile faster and effectively.  To learn more on what Oracle has to offer, check out the Oracle ADF Mobile (hybrid) and ADF Faces/ADF Mobile browser (Web Mobile) solutions from Oracle.   Additional Information Blog: ADF Blog Product Information on OTN: ADF Mobile Product Information on Oracle.com: Oracle Fusion Middleware Follow us on Twitter and Facebook Subscribe to our regular Fusion Middleware Newsletter

  Read the article

• VNIC - New feature of AK8 - Working with VNICs

  - by Steve Tunstall

  One of the important new features of the AK8 code is the ability to use multiple IP addresses on the same physical network port. This feature is called VNICs, or Virtual NICs. This allows us to no longer "burn" a whole port in a cluster when one cluster peer owns a network port. Traditionally, we have had to leave Net0 empty on controller 2, because it was used for managing controller 1. Vise-versa for Net1 on Controller 1. Then, if you have data going over 10GigE ports, you probably only had half of your ports running at any given time, and the partner 10GigE port on the other controller just sat there, doing nothing, unless the first controller went down. What a waste. Those days are over.  I want to thank and give a big shout-out to our good partner, OnX Enterprise Solutions, for allowing me to come into their lab and play around with their 7320 to do this demo. They let me make a big mess of their lab for the day as I played around with VNICs. If you're looking for a partner who knows Oracle well and can also piece together a solution from multiple vendors to get you what you need, OnX is a good choice. If you would like to talk to your local OnX rep, you can contact Scott Gill at [email protected] and he can point you in the right direction for your area.  Here we go: Here is what your Datalinks window looks like BEFORE you upgrade to AK8. Here's what the same screen looks like after you upgrade. See the new box? So here is my current network setup. I have my 4 physical interfaces setup each with an IP address. If I ping them, no problems.  So I can ping 180, 181, 251, and 252. However, if I try to ping 240, it does not work, as the 240 address is not being used by any of these interfaces, right?Let's change that. Here, I'm going to make a new Datalink by clicking the Datalink "Plus sign" button. I will check the VNIC box and tell it to use igb2, even though another interface is already using it. Now, I will create a new Interface, and choose "v_dl2" for it's datalink. My new network screen looks like this. A few things to take note of here. First, when I click the "igb2" device, it only highlights dl2 and int2. It does not highlight v_dl2 or v_int2.I think it should, but OK, it looks like VNICs don't highlight when you click the device. Second, note how the underscore character in v_dl2 and v_int2 do not seem to show on this screen. You can see it plainly if you go in and edit them, but from here it looks like a space instead of an underscore. Just a cosmetic bug, but something to be aware of. Now, if I click the VNIC datalink "v_dl2", on the other hand, it DOES highlight the device it belongs to, as it should. Seen here: Note that it did not, however, highlight int2 with it, even though int2 is connected to igb2. That's because we clicked v_dl2, which int2 has nothing to do with. So I'm OK with that. So let's try pinging 240 now. Of course, it works great.  So I now make another VNIC, and call it v_dl3 using igb3, and v_int3 with an address of 241. I then setup three shares, using ports 251, 240, and 241.Remember that IP 251 and 240 both are using the same physical port of igb2, and IP 241 is using port igb3. Next, I copy a folder full of stuff over to all three shares at the same time. I have analytics going so I can see the traffic. My top chart is showing the logical interfaces, and the bottom chart is showing the physical ports.Sure enough, look at the igb2 and vnic1 interfaces. They equal the traffic going over the igb2 physical port on the second chart. VNIC2, on the other hand, gets igb3 all to itself. This would work the same way with 10Gig or Infiniband ports. You can now have multiple IP addresses and even completely different subnets sharing the same physical ports. You may need to make route table entries for that. This allows us to use all of the ports you paid for with no more waste.  Very, very cool.  One small "bug" I found when doing this. It's really not a bug, it was designed to do this when VNICs were not around. But now that we have NVIC capability, they should probably change this. I've alerted the engineering team about this and they're looking into it, so perhaps it will be fixed in a later code. Here it is. Remember when we made the new VNIC datalink, I specifically said to click on the "Plus Sign" button to create it? I don't always do that. I really like to use the drag-and-drop method to create my datalinks in the network screen.HOWEVER, if you were to do that for building a VNIC, it will mess you up a little. Watch this. Here, I'm dragging igb3 over to make a new datalink. igb3 is already being used by dl3, but I'm going to make this a VNIC, so who cares, right? Well, the ZFSSA does not KNOW you are going to make it a VNIC, now does it? So... it works as designed and REMOVES the igb3 device from the current dl3 datalink in the background. See how it's now missing? At the same time, the dl3 datalink choice is missing from my list of possible VNICs for me to choose from!!!! Hey!!! I wanted to pick dl3. Why isn't it on the list??? Well, it can't be on this list because dl3 no longer has a device associated with it. Bummer for you. When you click cancel, the device is still missing from dl3. The fix is easy. Just edit dl3 by clicking the pencil button, do absolutely nothing, and click "Apply". The device will magically come back. Now, make the VNIC datalink by clicking the "Plus Sign" button. Sure enough, once you check the VNIC box, dl3 is a valid choice. No problem.  That's it for now. Have fun with VNICs.

  Read the article

• What does it mean when ARP shows <incomplete> on eth1

  - by Geoff Dalgas

  We have been using HAProxy along with heartbeat from the Linux-HA project. We are using two linux instances to provide a failover. Each server has with their own public IP and a single IP which is shared between the two using a virtual interface (eth1:1) at IP: 69.59.196.211 The virtual interface (eth1:1) IP 69.59.196.211 is configured as the gateway for the windows servers behind them and we use ip_forwarding to route traffic. We are experiencing an occasional network outage on one of our windows servers behind our linux gateways. HAProxy will detect the server is offline which we can verify by remoting to the failed server and attempting to ping the gateway: Pinging 69.59.196.211 with 32 bytes of data: Reply from 69.59.196.220: Destination host unreachable. Running arp -a on this failed server shows that there is no entry for the gateway address (69.59.196.211): Interface: 69.59.196.220 --- 0xa Internet Address Physical Address Type 69.59.196.161 00-26-88-63-c7-80 dynamic 69.59.196.210 00-15-5d-0a-3e-0e dynamic 69.59.196.212 00-21-5e-4d-45-c9 dynamic 69.59.196.213 00-15-5d-00-b2-0d dynamic 69.59.196.215 00-21-5e-4d-61-1a dynamic 69.59.196.217 00-21-5e-4d-2c-e8 dynamic 69.59.196.219 00-21-5e-4d-38-e5 dynamic 69.59.196.221 00-15-5d-00-b2-0d dynamic 69.59.196.222 00-15-5d-0a-3e-09 dynamic 69.59.196.223 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 225.0.0.1 01-00-5e-00-00-01 static On our linux gateway instances arp -a shows: peak-colo-196-220.peak.org (69.59.196.220) at <incomplete> on eth1 stackoverflow.com (69.59.196.212) at 00:21:5e:4d:45:c9 [ether] on eth1 peak-colo-196-215.peak.org (69.59.196.215) at 00:21:5e:4d:61:1a [ether] on eth1 peak-colo-196-219.peak.org (69.59.196.219) at 00:21:5e:4d:38:e5 [ether] on eth1 peak-colo-196-222.peak.org (69.59.196.222) at 00:15:5d:0a:3e:09 [ether] on eth1 peak-colo-196-209.peak.org (69.59.196.209) at 00:26:88:63:c7:80 [ether] on eth1 peak-colo-196-217.peak.org (69.59.196.217) at 00:21:5e:4d:2c:e8 [ether] on eth1 Why would arp occasionally set the entry for this failed server as <incomplete>? Should we be defining our arp entries statically? I've always left arp alone since it works 99% of the time, but in this one instance it appears to be failing. Are there any additional troubleshooting steps we can take help resolve this issue? THINGS WE HAVE TRIED I added a static arp entry for testing on one of the linux gateways which still didn't help. root@haproxy2:~# arp -a peak-colo-196-215.peak.org (69.59.196.215) at 00:21:5e:4d:61:1a [ether] on eth1 peak-colo-196-221.peak.org (69.59.196.221) at 00:15:5d:00:b2:0d [ether] on eth1 stackoverflow.com (69.59.196.212) at 00:21:5e:4d:45:c9 [ether] on eth1 peak-colo-196-219.peak.org (69.59.196.219) at 00:21:5e:4d:38:e5 [ether] on eth1 peak-colo-196-209.peak.org (69.59.196.209) at 00:26:88:63:c7:80 [ether] on eth1 peak-colo-196-217.peak.org (69.59.196.217) at 00:21:5e:4d:2c:e8 [ether] on eth1 peak-colo-196-220.peak.org (69.59.196.220) at 00:21:5e:4d:30:8d [ether] PERM on eth1 root@haproxy2:~# arp -i eth1 -s 69.59.196.220 00:21:5e:4d:30:8d root@haproxy2:~# ping 69.59.196.220 PING 69.59.196.220 (69.59.196.220) 56(84) bytes of data. --- 69.59.196.220 ping statistics --- 7 packets transmitted, 0 received, 100% packet loss, time 6006ms Rebooting the windows web server solves this issue temporarily with no other changes to the network but our experience shows this issue will come back. Swapping network cards and switches I noticed the link light on the port of the switch for the failed windows server was running at 100Mb instead of 1Gb on the failed interface. I moved the cable to several other open ports and the link indicated 100Mb for each port that I tried. I also swapped the cable with the same result. I tried changing the properties of the network card in windows and the server locked up and required a hard reset after clicking apply. This windows server has two physical network interfaces so I have swapped the cables and network settings on the two interfaces to see if the problem follows the interface. If the public interface goes down again we will know that it is not an issue with the network card. (We also tried another switch we have on hand, no change) Changing network hardware driver versions We've had the same problem with the latest Broadcom driver, as well as the built-in driver that ships in Windows Server 2008 R2. Replacing network cables As a last ditch effort we remembered another change that occurred was the replacement of all of the patch cords between our servers / switch. We had purchased two sets, one green of lengths 1ft - 3ft for the private interfaces and another set of red cables for the public interfaces. We swapped out all of the public interface patch cables with a different brand and ran our servers without issue for a full week ... aaaaaand then the problem recurred. Disable checksum offload, remove TProxy We also tried disabling TCP/IP checksum offload in the driver, no change. We're now pulling out TProxy and moving to a more traditional x-forwarded-for network arrangement without any fancy IP address rewriting. We'll see if that helps.

  Read the article

• OSX 10.6 Cisco IPSEC strange behavior

  - by tair

  I'm trying to connect to Cisco IPSEC VPN of my company over DSL Internet. I managed to successfully connect using Cisco VPN Client, now I'm trying to switch to OSX 10.6 native client, because of licensing issues. The problems is that the connection fails with a dialog box containing the message: The negotiation with the VPN server failed. Verify the server address and try reconnecting. I checked logs: Jun 29 13:10:39 racoon[4551]: Connecting. Jun 29 13:10:39 racoon[4551]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1). Jun 29 13:10:39 racoon[4551]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2). Jun 29 13:10:39 racoon[4551]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2). Jun 29 13:10:39 racoon[4551]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode). Jun 29 13:10:39 racoon[4551]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3). Jun 29 13:10:42 racoon[4551]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:10:42 racoon[4551]: IKEv1 XAUTH: success. (XAUTH Status is OK). Jun 29 13:10:42 racoon[4551]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:10:42 racoon[4551]: IKEv1 Config: retransmited. (Mode-Config retransmit). Jun 29 13:10:42 racoon[4551]: IKE Packet: receive success. (MODE-Config). Jun 29 13:10:42 configd[19]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.1.107), current interface setting (name: u92.168.54.147, subnet: 255.255.255.0, destination: 192.168.54.147). Jun 29 13:10:42 configd[19]: network configuration changed. Jun 29 13:10:42 vmnet-bridge[111]: Dynamic store changed Jun 29 13:10:42 named[62]: not listening on any interfaces Jun 29 13:10:58: --- last message repeated 1 time --- Jun 29 13:10:58 configd[19]: SCNCController: Disconnecting. (Connection tried to negotiate for, 16 seconds). Jun 29 13:10:58 racoon[4551]: IKE Packet: transmit success. (Information message). Jun 29 13:10:58 racoon[4551]: IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA). Jun 29 13:10:58 racoon[4551]: Disconnecting. (Connection tried to negotiate for, 19.113382 seconds). Jun 29 13:10:58 named[62]: not listening on any interfaces Jun 29 13:10:58 vmnet-bridge[111]: Dynamic store changed Jun 29 13:10:58 named[62]: not listening on any interfaces Jun 29 13:10:58 configd[19]: network configuration changed. Then I opened Terminal, started pinging a server behind VPN, and tried to connect again. Now connection is OK! Logs this time: Jun 29 13:46:53 racoon[8136]: Connecting. Jun 29 13:46:53 racoon[8136]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1). Jun 29 13:46:53 racoon[8136]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2). Jun 29 13:46:53 racoon[8136]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2). Jun 29 13:46:53 racoon[8136]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode). Jun 29 13:46:53 racoon[8136]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:46:56 racoon[8136]: IKEv1 XAUTH: success. (XAUTH Status is OK). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:46:56 racoon[8136]: IKEv1 Config: retransmited. (Mode-Config retransmit). Jun 29 13:46:56 racoon[8136]: IKE Packet: receive success. (MODE-Config). Jun 29 13:46:56 configd[19]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.1.107), current interface settinaddress: 192.168.54.149, subnet: 255.255.255.0, destination: 192.168.54.149). Jun 29 13:46:56 vmnet-bridge[111]: Dynamic store changed Jun 29 13:46:56 named[62]: not listening on any interfaces Jun 29 13:46:56 configd[19]: network configuration changed. Jun 29 13:46:56 named[62]: not listening on any interfaces Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1). Jun 29 13:46:56 racoon[8136]: IKE Packet: receive success. (Initiator, Quick-Mode message 2). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3). Jun 29 13:46:56 racoon[8136]: IKEv1 Phase2 Initiator: success. (Initiator, Quick-Mode). Jun 29 13:46:56 racoon[8136]: Connected. Jun 29 13:46:56 configd[19]: SCNCController: Connected. I tested it several times and it consistently behaves the same. What is the magic?

  Read the article

• How do I configure OpenVPN for accessing the internet with one NIC?

  - by Lekensteyn

  I've been trying to get OpenVPN to work for three days. After reading many questions, the HOWTO, the FAQ and even parts of a guide to Linux networking, I cannot get my an Internet connection to the Internet. I'm trying to set up a OpenVPN server on a VPS, which will be used for: secure access to the Internet bypassing port restrictions (directadmin/2222 for example) an IPv6 connection (my client does only have IPv4 connectivity, while the VPS has both IPv4 and native IPv6 connectivity) (if possible) I can connect to my server and access the machine (HTTP), but Internet connectivity fails completely. I'm using ping 8.8.8.8 for testing whether my connection works or not. Using tcpdump and iptables -t nat -A POSTROUTING -j LOG, I can confirm that the packets reach my server. If I ping to 8.8.8.8 on the VPS, I get an echo-reply from 8.8.8.8 as expected. When pinging from the client, I do not get an echo-reply. The VPS has only one NIC: etho. It runs on Xen. Summary: I want to have a secure connection between my laptop and the Internet using OpenVPN. If that works, I want to have IPv6 connectivity as well. Network setup and software: Home laptop (eth0: 192.168.2.10) (tap0: 10.8.0.2) | | (running Kubuntu 10.10; OpenVPN 2.1.0-3ubuntu1) | wifi | router/gateway (gateway 192.168.2.1) | INTERNET | VPS (eth0:1.2.3.4) (gateway, tap0: 10.8.0.1) (running Debian 6; OpenVPN 2.1.3-2) wifi and my home router should not cause problems since all traffic goes encrypted over UDP port 1194. I've turned IP forwarding on: # echo 1 > /proc/sys/net/ipv4/ip_forward iptables has been configured to allow forwarding traffic as well: iptables -F FORWARD iptables -A FORWARD -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -A FORWARD -s 10.8.0.0/24 -j ACCEPT iptables -A FORWARD -j DROP I've tried each of these rules separately without luck (flushing the chains before executing): iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j SNAT --to 1.2.3.4 iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE route -n before (server): 1.2.3.4 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 1.2.3.4 0.0.0.0 UG 0 0 0 eth0 route -n after (server): 1.2.3.4 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.8.0.0 0.0.0.0 255.255.255.0 U 0 0 0 tap0 0.0.0.0 1.2.3.4 0.0.0.0 UG 0 0 0 eth0 route -n before (client): 192.168.2.0 0.0.0.0 255.255.255.0 U 2 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 wlan0 route -n after (client): 1.2.3.4 192.168.2.1 255.255.255.255 UGH 0 0 0 wlan0 10.8.0.0 0.0.0.0 255.255.255.0 U 0 0 0 tap0 192.168.2.0 0.0.0.0 255.255.255.0 U 2 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 0.0.0.0 10.8.0.1 128.0.0.0 UG 0 0 0 tap0 128.0.0.0 10.8.0.1 128.0.0.0 UG 0 0 0 tap0 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 wlan0 SERVER config proto udp dev tap ca ca.crt cert server.crt key server.key dh dh1024.pem server 10.8.0.0 255.255.255.0 push "redirect-gateway def1" ifconfig-pool-persist ipp.txt keepalive 10 120 tls-auth ta.key 0 comp-lzo user nobody group nobody persist-key persist-tun log-append openvpn-log verb 3 mute 10 CLIENT config dev tap proto udp remote 1.2.3.4 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert client.crt key client.key ns-cert-type server tls-auth ta.key 1 comp-lzo verb 3 mute 20 traceroute 8.8.8.8 works as expected (similar output without OpenVPN activated): 1 10.8.0.1 (10.8.0.1) 24.276 ms 26.891 ms 29.454 ms 2 gw03.sbp.directvps.nl (178.21.112.1) 31.161 ms 31.890 ms 34.458 ms 3 ge0-v0652.cr0.nik-ams.nl.as8312.net (195.210.57.105) 35.353 ms 36.874 ms 38.403 ms 4 ge0-v3900.cr0.nik-ams.nl.as8312.net (195.210.57.53) 41.311 ms 41.561 ms 43.006 ms 5 * * * 6 209.85.248.88 (209.85.248.88) 147.061 ms 36.931 ms 28.063 ms 7 216.239.49.36 (216.239.49.36) 31.109 ms 33.292 ms 216.239.49.28 (216.239.49.28) 64.723 ms 8 209.85.255.130 (209.85.255.130) 49.350 ms 209.85.255.126 (209.85.255.126) 49.619 ms 209.85.255.122 (209.85.255.122) 52.416 ms 9 google-public-dns-a.google.com (8.8.8.8) 41.266 ms 44.054 ms 44.730 ms If you have any suggestions, please comment or answer. Thanks in advance.

  Read the article

• OSX 10.6 Cisco IPSEC strange behavior

  - by tair

  I'm trying to connect to Cisco IPSEC VPN of my company over DSL Internet. I managed to successfully connect using Cisco VPN Client, now I'm trying to switch to OSX 10.6 native client, because of licensing issues. The problems is that the connection fails with a dialog box containing the message: The negotiation with the VPN server failed. Verify the server address and try reconnecting. I checked logs: Jun 29 13:10:39 racoon[4551]: Connecting. Jun 29 13:10:39 racoon[4551]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1). Jun 29 13:10:39 racoon[4551]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2). Jun 29 13:10:39 racoon[4551]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2). Jun 29 13:10:39 racoon[4551]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode). Jun 29 13:10:39 racoon[4551]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3). Jun 29 13:10:42 racoon[4551]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:10:42 racoon[4551]: IKEv1 XAUTH: success. (XAUTH Status is OK). Jun 29 13:10:42 racoon[4551]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:10:42 racoon[4551]: IKEv1 Config: retransmited. (Mode-Config retransmit). Jun 29 13:10:42 racoon[4551]: IKE Packet: receive success. (MODE-Config). Jun 29 13:10:42 configd[19]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.1.107), current interface setting (name: u92.168.54.147, subnet: 255.255.255.0, destination: 192.168.54.147). Jun 29 13:10:42 configd[19]: network configuration changed. Jun 29 13:10:42 vmnet-bridge[111]: Dynamic store changed Jun 29 13:10:42 named[62]: not listening on any interfaces Jun 29 13:10:58: --- last message repeated 1 time --- Jun 29 13:10:58 configd[19]: SCNCController: Disconnecting. (Connection tried to negotiate for, 16 seconds). Jun 29 13:10:58 racoon[4551]: IKE Packet: transmit success. (Information message). Jun 29 13:10:58 racoon[4551]: IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA). Jun 29 13:10:58 racoon[4551]: Disconnecting. (Connection tried to negotiate for, 19.113382 seconds). Jun 29 13:10:58 named[62]: not listening on any interfaces Jun 29 13:10:58 vmnet-bridge[111]: Dynamic store changed Jun 29 13:10:58 named[62]: not listening on any interfaces Jun 29 13:10:58 configd[19]: network configuration changed. Then I opened Terminal, started pinging a server behind VPN, and tried to connect again. Now connection is OK! Logs this time: Jun 29 13:46:53 racoon[8136]: Connecting. Jun 29 13:46:53 racoon[8136]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1). Jun 29 13:46:53 racoon[8136]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2). Jun 29 13:46:53 racoon[8136]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2). Jun 29 13:46:53 racoon[8136]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode). Jun 29 13:46:53 racoon[8136]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:46:56 racoon[8136]: IKEv1 XAUTH: success. (XAUTH Status is OK). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:46:56 racoon[8136]: IKEv1 Config: retransmited. (Mode-Config retransmit). Jun 29 13:46:56 racoon[8136]: IKE Packet: receive success. (MODE-Config). Jun 29 13:46:56 configd[19]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.1.107), current interface settinaddress: 192.168.54.149, subnet: 255.255.255.0, destination: 192.168.54.149). Jun 29 13:46:56 vmnet-bridge[111]: Dynamic store changed Jun 29 13:46:56 named[62]: not listening on any interfaces Jun 29 13:46:56 configd[19]: network configuration changed. Jun 29 13:46:56 named[62]: not listening on any interfaces Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1). Jun 29 13:46:56 racoon[8136]: IKE Packet: receive success. (Initiator, Quick-Mode message 2). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3). Jun 29 13:46:56 racoon[8136]: IKEv1 Phase2 Initiator: success. (Initiator, Quick-Mode). Jun 29 13:46:56 racoon[8136]: Connected. Jun 29 13:46:56 configd[19]: SCNCController: Connected. I tested it several times and it consistently behaves the same. What is the magic?

  Read the article

• Wireless internet connection connects but internet does not work (no packets received). Wired does.

  - by Rodney

  When I connect my PC via ethernet cable to my ADSL router it works fine. When I connect via Wireless it connects and the internet will work for a random amount of time and then stop working. It stays connected with a strong signal but no packets are received. My laptop/iphone are right next to it and wireless works fine. If I open the Wireless USB status, it says it is connected to my SSID with full strength (54 mps - I am 3 meteres away from my router) and the activty shows as Packets 594 SENT and 105 RECEIVED (this goes up VERY slowly) I have tried the following: Turned off anitvirus and firewall completely. Tested the wifi signal- I am writing this on my laptop which is next to my PC and also has full wifi strength. Tried a different wireless adapter - I dug out an old PCI wireless card - it does the exact same thing. Compared all wireless settings to my laptop. I can ping google.com and it replies (sometimes with packet loss) When I reboot the PC it will connect for a minute or two (random time) and then just stops again. I tried Firefox, IE etc. no joy I have updated all latest versions (Netgear WG111v2) and drivers Checked Event Log - nothing unusual Ping the router (and even connect as admin for the few minutes when the internet does work) Changed the MTU down to 1200 using DrTCP Checked Device Manager for conflicts - none. I ping the router from the PC (192.168.0.10 - 192.168.0.1) and it replies with 4 packets. BUT, on my router admin page (which I access via http on my laptop wirelessly) - if I ping 192.168.0.10 all packets timeout (pinging my laptop 192.168.0.12 works fine) My router admin page shows the leased IP address for 192.168.0.10 (ie it is definitely talking to the router initially) Now I am out of ideas - please help. I think it is an OS/Software issue as I have tried 2 different wireless adapaters (PCI and USB) with the same result but all other wireless devices work fine around mine). It's not the firewall. It is getting assigned an IP address correctly (my PC gets 192.168.0.10, my laptop is .12) It is assigned by DHCP. As soon as I plug in the ethernet cable it all works fine. Repairing the adapter sometimes helps but it will always stop working after a random time. The wireless adapter always shows as connected with Excellent signal but the internet does not work. I am running Windows XP SP3 and have tried a Netgear WG111v2 USB adapter. Thanks in advance! UPDATE: The internet seems to be working, it is just either sending packets too small or slow to work (some small pages load bits of them very slowly but then hang). XP seems to have a networking diagnostic app - here is the output: Last diagnostic run time: 08/30/10 08:16:38 IP Configuration Diagnostic Invalid IP address info Valid IP address detected: 192.168.0.10 IP Layer Diagnostic Corrupted IP routing table info The default route is valid info The loopback route is valid info The local host route is valid info The local subnet route is valid Invalid ARP cache entries action The ARP cache has been flushed Gateway Diagnostic Gateway info The following proxy configuration is being used by IE: Automatically Detect Settings:Disabled Automatic Configuration Script: Proxy Server: Proxy Bypass list: info This computer has the following default gateway entry(ies): 192.168.0.1 info This computer has the following IP address(es): 192.168.0.10 info The default gateway is in the same subnet as this computer info The default gateway entry is a valid unicast address info The default gateway address was resolved via ARP in 1 try(ies) info The default gateway was reached via ICMP Ping in 1 try(ies) info TCP port 80 on host 65.55.12.249 was successfully reached info The Internet host www.microsoft.com was successfully reached info The default gateway is OK DNS Client Diagnostic DNS - Not a home user scenario info Using Web Proxy: no info Resolving name ok for (www.microsoft.com): yes No DNS servers DNS failure HTTP, HTTPS, FTP Diagnostic HTTP, HTTPS, FTP connectivity info FTP (Passive): Successfully connected to ftp.microsoft.com. info HTTP: Successfully connected to www.microsoft.com. warn HTTPS: Error 12002 connecting to www.microsoft.com: The operation timed out warn HTTPS: Error 12002 connecting to www.passport.net: The operation timed out error Could not make an HTTPS connection. info Redirecting user to support call WinSock Diagnostic WinSock status info All base service provider entries are present in the Winsock catalog. info The Winsock Service provider chains are valid. info Provider entry MSAFD Tcpip [TCP/IP] passed the loopback communication test. info Provider entry MSAFD Tcpip [UDP/IP] passed the loopback communication test. info Provider entry RSVP UDP Service Provider passed the loopback communication test. info Provider entry RSVP TCP Service Provider passed the loopback communication test. info Connectivity is valid for all Winsock service providers. Wireless Diagnostic Wireless - Service disabled Wireless - User SSID action User input required: Specify network name or SSID Wireless - First time setup info The Wireless Network name (SSID) to which the user would like to connect = RodSof Wifi. Wireless - Radio off info Valid IP address detected: 192.168.0.10 Wireless - Out of range Wireless - Hardware issue Wireless - Novice user Wireless - Ad-hoc network Wireless - Less preferred Wireless - 802.1x enabled Wireless - Configuration mismatch Wireless - Low SNR Network Adapter Diagnostic Network location detection info Using home Internet connection Network adapter identification info Network connection: Name=Local Area Connection 2, Device=Realtek RTL8168C(P)/8111C(P) PCI-E Gigabit Ethernet NIC, MediaType=LAN, SubMediaType=LAN info Network connection: Name=Wireless USB, Device=NETGEAR WG111v2 54Mbps Wireless USB 2.0 Adapter, MediaType=LAN, SubMediaType=WIRELESS info Both Ethernet and Wireless connections available, prompting user for selection action User input required: Select network connection info Wireless connection selected Network adapter status info Network connection status: Connected HTTP, HTTPS, FTP Diagnostic HTTP, HTTPS, FTP connectivity info FTP (Active): Successfully connected to ftp.microsoft.com. warn HTTP: Error 12007 connecting to www.microsoft.com: The server name or address could not be resolved warn HTTP: Error 12002 connecting to www.hotmail.com: The operation timed out warn HTTPS: Error 12002 connecting to www.passport.net: The operation timed out warn HTTPS: Error 12002 connecting to www.microsoft.com: The operation timed out error Could not make an HTTP connection. error Could not make an HTTPS connection.

  Read the article

• With dnsmasq as the DNS server, 'dig' and 'ping' succeed while 'nslookup' fails

  - by einpoklum

  I installed dnsmasq on a machine of mine (It's a Kubuntu 12.04 LTS), backed only by /etc/hosts (no connection to the Internet until later). Now, if I dig mymachine, I get 192.168.0.1, but if I try to nslookup mymachine, I get: >> connection timed out; no servers could be reached Tried also nslookup mymachine.mynicedomain.org - didn't work either. pinging (Edit:) succeeds. This happens both on the server machine itself and on other machines on the network. How can I the DNS lookups to work? What problem is preventing nslookup from succeeding? Additional Information In the server's /etc/hosts: 192.168.0.1 mymachine In the server's nsswitch.conf: hosts: files mdns4_mininal [NOTFOUND=return] dns mdns4 (admittedly, this is a bit weird; but I also tried: hosts: files dns instead, with the same effect) In resolv.conf (which is generated by dnsmasq): nameserver 127.0.0.1 search mynicedomain.org In the server's /etc/hosts.allow: domain: ALL In the other machines' /etc/resolv.conf (this is set by the DHCP client): nameserver 192.168.0.1 search mynicedomain.org Relevant netstat output on the server: Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 127.0.0.1:53 0.0.0.0:* LISTEN tcp 0 0 192.168.0.1:53 0.0.0.0:* LISTEN Finally, here's the ipconfig output from one of the client machines on the network (running Windows 7): Connection-specific DNS Suffix . : mynicedomain.org Description . . . . . . . . . . . : Intel(R) 82579LM Gigabit Network Connection Physical Address. . . . . . . . . : 12-34-56-78-9A-BC DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.0.50(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : Sunday, October 20th 2013 16:20:25 Lease Expires . . . . . . . . . . : Sunday, October 20th 2013 18:20:24 Default Gateway . . . . . . . . . : 192.168.0.1 DHCP Server . . . . . . . . . . . : 192.168.0.1 DNS Servers . . . . . . . . . . . : 192.168.0.1 NetBIOS over Tcpip. . . . . . . . : Enabled Notes: May be related to this question.

  Read the article

• Cluster failover and strange gratuitous arp behavior

  - by lazerpld

  I am experiencing a strange Windows 2008R2 cluster related issue that is bothering me. I feel that I have come close as to what the issue is, but still don't fully understand what is happening. I have a two node exchange 2007 cluster running on two 2008R2 servers. The exchange cluster application works fine when running on the "primary" cluster node. The problem occurs when failing over the cluster ressource to the secondary node. When failing over the cluster to the "secondary" node, which for instance is on the same subnet as the "primary", the failover initially works ok and the cluster ressource continues to work for a couple of minutes on the new node. Which means that the recieving node does send out a gratuitous arp reply packet that updated the arp tables on the network. But after x amount of time (typically within 5 minutes time) something updates the arp-tables again because all of a sudden the cluster service does not answer to pings. So basically I start a ping to the exchange cluster address when its running on the "primary node". It works just great. I failover the cluster ressource group to the "secondary node" and I only have loss of one ping which is acceptable. The cluster ressource still answers for some time after being failed over and all of a sudden the ping starts timing out. This is telling me that the arp table initially is updated by the secondary node, but then something (which I haven't found out yet) wrongfully updates it again, probably with the primary node's MAC. Why does this happen - has anyone experienced the same problem? The cluster is NOT running NLB and the problem stops immidiately after failing over back to the primary node where there are no problems. Each node is using NIC teaming (intel) with ALB. Each node is on the same subnet and has gateway and so on entered correctly as far as I am concerned. Edit: I was wondering if it could be related to network binding order maybe? Because I have noticed that the only difference I can see from node to node is when showing the local arp table. On the "primary" node the arp table is generated on the cluster address as the source. While on the "secondary" its generated from the nodes own network card. Any input on this? Edit: Ok here is the connection layout. Cluster address: A.B.6.208/25 Exchange application address: A.B.6.212/25 Node A: 3 physical nics. Two teamed using intels teaming with the address A.B.6.210/25 called public The last one used for cluster traffic called private with 10.0.0.138/24 Node B: 3 physical nics. Two teamed using intels teaming with the address A.B.6.211/25 called public The last one used for cluster traffic called private with 10.0.0.139/24 Each node sits in a seperate datacenter connected together. End switches being cisco in DC1 and NEXUS 5000/2000 in DC2. Edit: I have been testing a little more. I have now created an empty application on the same cluster, and given it another ip address on the same subnet as the exchange application. After failing this empty application over, I see the exact same problem occuring. After one or two minutes clients on other subnets cannot ping the virtual ip of the application. But while clients on other subnets cannot, another server from another cluster on the same subnet has no trouble pinging. But if i then make another failover to the original state, then the situation is the opposite. So now clients on same subnet cannot, and on other they can. We have another cluster set up the same way and on the same subnet, with the same intel network cards, the same drivers and same teaming settings. Here we are not seeing this. So its somewhat confusing. Edit: OK done some more research. Removed the NIC teaming of the secondary node, since it didnt work anyway. After some standard problems following that, I finally managed to get it up and running again with the old NIC teaming settings on one single physical network card. Now I am not able to reproduce the problem described above. So it is somehow related to the teaming - maybe some kind of bug? Edit: Did some more failing over without being able to make it fail. So removing the NIC team looks like it was a workaround. Now I tried to reestablish the intel NIC teaming with ALB (as it was before) and i still cannot make it fail. This is annoying due to the fact that now i actually cannot pinpoint the root of the problem. Now it just seems to be some kind of MS/intel hick-up - which is hard to accept because what if the problem reoccurs in 14 days? There is a strange thing that happened though. After recreating the NIC team I was not able to rename the team to "PUBLIC" which the old team was called. So something has not been cleaned up in windows - although the server HAS been restarted! Edit: OK after restablishing the ALB teaming the error came back. So I am now going to do some thorough testing and i will get back with my observations. One thing is for sure. It is related to Intel 82575EB NICS, ALB and Gratuitous Arp.

  Read the article

• With dnsmasq as the DNS server, 'dig' succeeds, but 'nslookup' and 'ping' fail

  - by einpoklum

  I installed dnsmasq on a machine of mine (It's a Kubuntu 12.04 LTS), backed only by /etc/hosts (no connection to the Internet until later). Now, when I'm on the same machine as the dnsmasq - or any other machine on the server, I can dig mymachine and get 192.168.0.1, but if I try to nslookup mymachine, I get: >> connection timed out; no servers could be reached Tried also nslookup mymachine.mynicedomain.org - didn't work either. pinging fails. How can I the DNS lookups to work? Is the problem with the nsswitch entries? The dnsmasq configuration? Additional Information In the server's /etc/hosts: 192.168.0.1 mymachine In the server's nsswitch.conf: hosts: files mdns4_mininal [NOTFOUND=return] dns mdns4 (admittedly, this is a bit weird) In resolv.conf (which is generated by dnsmasq): nameserver 127.0.0.1 search mynicedomain.org In the server's /etc/hosts.allow: domain: ALL In the other machines' /etc/resolv.conf (this is set by the DHCP client): nameserver 192.168.0.1 search mynicedomain.org Finally, here's the ipconfig output from one of the client machines on the network (running Windows 7): Connection-specific DNS Suffix . : mynicedomain.org Description . . . . . . . . . . . : Intel(R) 82579LM Gigabit Network Connection Physical Address. . . . . . . . . : 12-34-56-78-9A-BC DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.0.50(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : Sunday, October 20th 2013 16:20:25 Lease Expires . . . . . . . . . . : Sunday, October 20th 2013 18:20:24 Default Gateway . . . . . . . . . : 192.168.0.1 DHCP Server . . . . . . . . . . . : 192.168.0.1 DNS Servers . . . . . . . . . . . : 192.168.0.1 NetBIOS over Tcpip. . . . . . . . : Enabled Notes: May be related to this question.

  Read the article

• OpenVPN - client-to-client traffic working in one direction but not the other

  - by Pawz

  I have the following VPN configuration: +------------+ +------------+ +------------+ | outpost |----------------| kino |----------------| guchuko | +------------+ +------------+ +------------+ OS: FreeBSD 6.2 OS: Gentoo 2.6.32 OS: Gentoo 2.6.33.3 Keyname: client3 Keyname: server Keyname: client1 eth0: 10.0.1.254 eth0: 203.x.x.x eth0: 192.168.0.6 tun0: 192.168.150.18 tun0: 192.168.150.1 tun0: 192.168.150.10 P-t-P: 192.166.150.17 P-t-P: 192.168.150.2 P-t-P: 192.168.150.9 Kino is the server and has client-to-client enabled. I am using "fragment 1400" and "mssfix" on all three machines. An mtu-test on both connections is successful. All three machines have ip forwarding enabled, by this on the gentoo boxes: net.ipv4.conf.all.forwarding = 1 And this on the FreeBSD box: net.inet.ip.forwarding: 1 In the server's "ccd" directory is the following files: client1: iroute 192.168.0.0 255.255.255.0 client3: iroute 10.0.1.0 255.255.255.0 The server config has these routes configured: push "route 192.168.0.0 255.255.255.0" push "route 10.0.1.0 255.255.255.0" route 192.168.0.0 255.255.255.0 route 10.0.1.0 255.255.255.0 Kino's routing table looks like this: 192.168.150.0 192.168.150.2 255.255.255.0 UG 0 0 0 tun0 10.0.1.0 192.168.150.2 255.255.255.0 UG 0 0 0 tun0 192.168.0.0 192.168.150.2 255.255.255.0 UG 0 0 0 tun0 192.168.150.2 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 Outpost's like this: 192.168.150 192.168.150.17 UGS 0 17 tun0 192.168.0 192.168.150.17 UGS 0 2 tun0 192.168.150.17 192.168.150.18 UH 3 0 tun0 And Guchuko's like this: 192.168.150.0 192.168.150.9 255.255.255.0 UG 0 0 0 tun0 10.0.1.0 192.168.150.9 255.255.255.0 UG 0 0 0 tun0 192.168.150.9 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 Now, the tests. Pings from Guchuko to Outpost's LAN IP work OK, as does the reverse - pings from Outpost to Guchuko's LAN IP. However... Pings from Outpost, to a machine on Guchuko's LAN work fine: .(( root@outpost )). (( 06:39 PM )) :: ~ :: # ping 192.168.0.3 PING 192.168.0.3 (192.168.0.3): 56 data bytes 64 bytes from 192.168.0.3: icmp_seq=0 ttl=63 time=462.641 ms 64 bytes from 192.168.0.3: icmp_seq=1 ttl=63 time=557.909 ms But a ping from Guchuko, to a machine on Outpost's LAN does not: .(( root@guchuko )). (( 06:43 PM )) :: ~ :: # ping 10.0.1.253 PING 10.0.1.253 (10.0.1.253) 56(84) bytes of data. --- 10.0.1.253 ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2000ms Guchuko's tcpdump of tun0 shows: 18:46:27.716931 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 1, length 64 18:46:28.716715 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 2, length 64 18:46:29.716714 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 3, length 64 Outpost's tcpdump on tun0 shows: 18:44:00.333341 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 3, length 64 18:44:01.334073 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 4, length 64 18:44:02.331849 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 5, length 64 So Outpost is receiving the ICMP request destined for the machine on it's subnet, but appears not be forwarding it. Outpost has gateway_enable="YES" in its rc.conf which correctly sets net.inet.ip.forwarding to 1 as mentioned earlier. As far as I know, that's all that's required to make a FreeBSD box forward packets between interfaces. Is there something else I could be forgetting ? FWIW, pinging 10.0.1.253 from Kino has the same result - the traffic does not get forwarded. UPDATE: I've found that I can only ping certain IP's on Guchuko's LAN from Outpost. From Outpost I can ping 192.168.0.3 and 192.168.0.2, but 192.168.99 and 192.168.0.4 are unreachable. The same tcpdump behavior can be seen. I think this means the problem can't be due to ipforwarding or routing, because Outpost can reach SOME hosts on Guchuko's LAN but not others and likewise, Guchuko can reach two hosts on Outpost's LAN, but not others. This baffles me.

  Read the article

• ASA 5540 v8.4(3) vpn to ASA 5505 v8.2(5), tunnel up but I cant ping from 5505 to IP on other side

  - by user223833

  I am having problems pinging from a 5505(remote) to IP 10.160.70.10 in the network behind the 5540(HQ side). 5505 inside IP: 10.56.0.1 Out: 71.43.109.226 5540 Inside: 10.1.0.8 out: 64.129.214.27 I Can ping from 5540 to 5505 inside 10.56.0.1. I also ran ASDM packet tracer in both directions, it is ok from 5540 to 5505, but drops the packet from 5505 to 5540. It gets through the ACL and dies at the NAT. Here is the 5505 config, I am sure it is something simple I am missing. ASA Version 8.2(5) ! hostname ASA-CITYSOUTHDEPOT domain-name rngint.net names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 10.56.0.1 255.255.0.0 ! interface Vlan2 nameif outside security-level 0 ip address 71.43.109.226 255.255.255.252 ! banner motd ***ASA-CITYSOUTHDEPOT*** banner asdm CITY SOUTH DEPOT ASA5505 ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns server-group DefaultDNS domain-name rngint.net access-list outside_1_cryptomap extended permit ip host 71.43.109.226 host 10.1.0.125 access-list outside_1_cryptomap extended permit ip 10.56.0.0 255.255.0.0 10.0.0.0 255.0.0.0 access-list outside_1_cryptomap extended permit ip 10.56.0.0 255.255.0.0 10.106.70.0 255.255.255.0 access-list outside_1_cryptomap extended permit ip 10.56.0.0 255.255.0.0 10.106.130.0 255.255.255.0 access-list outside_1_cryptomap extended permit ip host 71.43.109.226 host 10.160.70.10 access-list inside_nat0_outbound extended permit ip host 71.43.109.226 host 10.1.0.125 access-list inside_nat0_outbound extended permit ip 10.56.0.0 255.255.0.0 10.0.0.0 255.0.0.0 access-list inside_nat0_outbound extended permit ip 10.56.0.0 255.255.0.0 10.106.130.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip 10.56.0.0 255.255.0.0 10.106.70.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip host 71.43.109.226 10.106.70.0 255.255.255.0 pager lines 24 logging enable logging buffer-size 25000 logging buffered informational logging asdm warnings mtu inside 1500 mtu outside 1500 icmp unreachable rate-limit 1 burst-size 1 icmp permit any inside no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 route outside 0.0.0.0 0.0.0.0 71.43.109.225 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy aaa-server TACACS+ protocol tacacs+ aaa-server TACACS+ (inside) host 10.106.70.36 key ***** aaa authentication http console LOCAL aaa authentication ssh console LOCAL aaa authorization exec authentication-server http server enable http 192.168.1.0 255.255.255.0 inside http 10.0.0.0 255.0.0.0 inside http 0.0.0.0 0.0.0.0 outside snmp-server host inside 10.106.70.7 community ***** no snmp-server location no snmp-server contact snmp-server community ***** snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto map outside_map 1 match address outside_1_cryptomap crypto map outside_map 1 set pfs group1 crypto map outside_map 1 set peer 64.129.214.27 crypto map outside_map 1 set transform-set ESP-3DES-SHA crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption des hash md5 group 2 lifetime 86400 telnet timeout 5 ssh 10.0.0.0 255.0.0.0 inside ssh 0.0.0.0 0.0.0.0 outside ssh timeout 5 console timeout 0 management-access inside dhcpd auto_config outside ! dhcpd address 10.56.0.100-10.56.0.121 inside dhcpd dns 10.1.0.125 interface inside dhcpd auto_config outside interface inside ! dhcprelay server 10.1.0.125 outside dhcprelay enable inside dhcprelay setroute inside dhcprelay timeout 60 threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept tftp-server inside 10.1.1.25 CITYSOUTHDEPOT-ASA-Confg webvpn tunnel-group 64.129.214.27 type ipsec-l2l tunnel-group 64.129.214.27 ipsec-attributes pre-shared-key ***** ! ! prompt hostname context

  Read the article

• Why does my ping command (Windows) results alternate between "timeout" and "network is not reachable"?

  - by Sopalajo de Arrierez

  My Windows is in Spanish, so I will have to paste console outputs in that language (I think that translating without knowing the exact terms used in english versions could give worse results than leaving it as it appears on screen). This is the issue: when pinging a non-existent IP from a WinXP-SP3 machine (clean Windows install, just formatted), I get sometimes a "Timeout" result, and sometimes a "network is not reachable" message. This is the result of: ping 192.168.210.1 Haciendo ping a 192.168.210.1 con 32 bytes de datos: Tiempo de espera agotado para esta solicitud. Respuesta desde 80.58.67.86: Red de destino inaccesible. Respuesta desde 80.58.67.86: Red de destino inaccesible. Tiempo de espera agotado para esta solicitud. Estadísticas de ping para 192.168.210.1: Paquetes: enviados = 4, recibidos = 2, perdidos = 2 (50% perdidos), Tiempos aproximados de ida y vuelta en milisegundos: Mínimo = 0ms, Máximo = 0ms, Media = 0ms 192.168.210.1 does not exist on the network. DHCP client is enabled, and the computer gets assigned those network config by the router. My IP: 192.168.11.2 Netmask: 255.255.255.0 Gateway: 192.168.11.1 DNS: 80.58.0.33/194.224.52.36 This is the output from "route print command": =========================================================================== Rutas activas: Destino de red Máscara de red Puerta de acceso Interfaz Métrica 0.0.0.0 0.0.0.0 192.168.11.1 192.168.11.2 20 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.11.0 255.255.255.0 192.168.11.2 192.168.11.2 20 192.168.11.2 255.255.255.255 127.0.0.1 127.0.0.1 20 192.168.11.255 255.255.255.255 192.168.11.2 192.168.11.2 20 224.0.0.0 240.0.0.0 192.168.11.2 192.168.11.2 20 255.255.255.255 255.255.255.255 192.168.11.2 192.168.11.2 1 255.255.255.255 255.255.255.255 192.168.11.2 3 1 Puerta de enlace predeterminada: 192.168.11.1 =========================================================================== Rutas persistentes: ninguno The output of: ping 1.1.1.1 Haciendo ping a 1.1.1.1 con 32 bytes de datos: Tiempo de espera agotado para esta solicitud. Tiempo de espera agotado para esta solicitud. Tiempo de espera agotado para esta solicitud. Tiempo de espera agotado para esta solicitud. Estadísticas de ping para 1.1.1.1: Paquetes: enviados = 4, recibidos = 0, perdidos = 4 1.1.1.1 does not exist on the network. and the output of: ping 10.1.1.1 Haciendo ping a 10.1.1.1 con 32 bytes de datos: Respuesta desde 80.58.67.86: Red de destino inaccesible. Tiempo de espera agotado para esta solicitud. Tiempo de espera agotado para esta solicitud. Respuesta desde 80.58.67.86: Red de destino inaccesible. Estadísticas de ping para 10.1.1.1: Paquetes: enviados = 4, recibidos = 2, perdidos = 2 (50% perdidos), 10.1.1.1 does not exist on the network. I can do some aproximate translation of what you demand if necessary. I have another computers in the same network (WinXP-SP3 and Win7-SP1), and they have, too, this problem. Gateway (Router): Buffalo WHR-HP-GN (official Buffalo firmware, not DD-WRT). I have some Linux (Debian/Kali) machine in my network, so I tested things on it: ping 192.168.210.1 PING 192.168.210.1 (192.168.210.1) 56(84) bytes of data. From 80.58.67.86 icmp_seq=1 Packet filtered From 80.58.67.86 icmp_seq=2 Packet filtered From 80.58.67.86 icmp_seq=3 Packet filtered From 80.58.67.86 icmp_seq=4 Packet filtered to the non-existing 1.1.1.1 : ping 1.1.1.1 PING 1.1.1.1 (1.1.1.1) 56(84) bytes of data. ^C --- 1.1.1.1 ping statistics --- 153 packets transmitted, 0 received, 100% packet loss, time 153215ms (no response after waiting a few minutes). and the non-existing 10.1.1.1: ping 10.1.1.1 PING 10.1.1.1 (10.1.1.1) 56(84) bytes of data. From 80.58.67.86 icmp_seq=20 Packet filtered From 80.58.67.86 icmp_seq=22 Packet filtered From 80.58.67.86 icmp_seq=23 Packet filtered From 80.58.67.86 icmp_seq=24 Packet filtered From 80.58.67.86 icmp_seq=25 Packet filtered What is going on here? I am posing this question mainly for learning purposes, but there is another reason: when all pings are returning "timeout", it creates an %ERRORLEVEL% value of 1, but if there is someone of "Network is not reachable" type, %ERRORLEVEL% goes to 0 (no error), and this could be inappropriate for a shell script (we can not use ping to detect, for example, if the network is down due to loss of contact with the gateway).

  Read the article

• Begin the Clone Wars Have!

  - by Antony Reynolds

  Creating a New Virtual Machine from an Existing Virtual Disk In previous posts I described how I set up an OEL6 machine under VirtualBox that can run an 11gR2 database and FMW 11.1.1.5.  That is great if you want the DB and FMW running in the same virtual image and it has served me well for some proof of concepts and also for some testing of different JVMs.  However I also wanted to run some testing of FMW with the database running on a separate physical machine.  So in this post I will show how to take a VirtualBox image and create a new image based on the disks from that original image. What are my Options? There is more than one way to skin a cat, or in this case to create two separate VMs that can run on different hardware.  Some of the options include: Create new virtual disk images for each new VM. Clone the existing disk images and point the new VM at the cloned images. Point the new VM at the existing snapshots. #1 is too much like hard work, install OEL twice, install a database again, install FMW again, run RCU again!  Life is too short! #2 is probably the safest way of doing things.  VirtualBox allows you to clone a disk image for use in a separate machine.  However this of course duplicates the disk and means that it is now occupying 3 times the space, once for the original disk and twice more for the two clones I would need. #3 is the most space efficient way of doing things.  It does mean however that I can only run the new “cloned” images if I have access to the original image because that is where the base snapshots reside.  However this is not a problem for me as long as I remember to keep all threee images together.  So this is the approach we will follow. Snapshot, What Snapshot? As we are going to create new virtual machines based on existing snapshots we need to figure out which snapshot to use.  We do this by opening the “Media Manager” from within VirtualBox and moving the mouse over the snapshot images until we find the snapshots we want – the snapshot name is identified in the “Attached to:” comment.  In my case I wanted the FMW installed snapshot because that had a database configured for FMW alongside the FMW software.  I made a note of the filename of that snapshot (actually I just noted the first 5 characters as that was all that was needed to uniquely identify the snapshot file). When we create the new machines we will point them at the snapshot filename we have just checked. Network or NotWork? Because we want the two new machines to communicate with each other when hosted in different physical machines we can’t use the default NAT networking mode without a lot of hassle.  But at the same time we need them to have fixed IP addresses relative to each other so that they can see each other whilst also being able to see the outside world. To achieve all these requirements I created two network adapters for each machine.  Adapter 1 was a standard NAT mapping.  This will allow each machine to get a dynamic IP address (10.0.2.15 by default) that can be used to access the external world through the VBox provided NAT gateway.  This is the same as the existing configuration. The second adapter I created as a bridged adapter.  This gives the virtual machine direct access to the host network card and by using fixed IP addresses each machine can see the other.  It is important to choose fixed IP addresses that are not routable across your internal network so you don’t get any clashes with other machines on your network.  Of course you could always get proper fixed IP addresses from your network people, but I have serveral people using my images and as long as I don’t have two instances of the same VM on the same network segment this is easier and avoids reconfiguring the network every time someone wants a copy of my VM.  If it is available I would suggest using the 10.0.3.* network as 10.0.2.* is the default NAT network.  You can check availability by pinging 10.0.3.1 and 10.0.3.2 from your host machine.  If it times out then you are probably safe to use that. Creating the New VMs Now that I had collected the data that I needed I went ahead and created the new VMs. When asked for a “Boot Hard Disk” I used the “Choose a virtual hard disk file…” link to find the snapshot I had previously selected and set that to be the existing hard disk.  I chose the previously existing SOA 11.1.1.5 install for both the new DB and FMW machines because that snapshot had the database with the RCU completed that I wanted for my DB machine and it had the SOA software installed which I wanted for my FMW machine. After the initial creation of the virtual machine go into the network setting section and enable a second adapter which will be bridged.  Make a note of the MAC addresses (the last four digits should be sufficient) of the two adapters so that you can later set the bridged adapter to use fixed IP and the NAT adapter to use DHCP. We are now ready to start the VMs and reconfigure Linux. Reconfiguring Linux Because I now have two new machines I need to change their network configuration.  In particular I need to change the hostname, update the hosts file and change the network settings. Changing the Hostname I renamed both hosts by running the hostname command as root: hostname vboxfmw.oracle.com I also edited the /etc/sysconfig file and set the correct hostname in there. HOSTNAME=vboxfmw.oracle.com Changing the Network Settings I needed to change the network configuration to give the bridged network a fixed IP address.  I first explicitly set the MAC addresses of the two adapters, because the order of the virtual adapters in the VirtualBox Manager is not necessarily the same as the order of the adapters in the guest OS.  So I went in to the System->Preferences->Network Connections screen and explicitly set the “Device MAC address” for the two adapters. Having correctly mapped the Linux adapters to the VirtualBox adapters I then set the Bridged adapter to use fixed IP addressing rather than DHCP.  There is no need for additional routing or default gateways because we expect the two machine to be on the same LAN segment. Updating the Hosts File Having renamed the machines and reconfigured the network I then updated the /etc/hosts file to refer to the new machine name add a new line to the hosts file to provide an additional IP address for my server (the new fixed IP address) add a new line for the fixed IP address of the other virtual machine 10.0.3.101      vboxdb.oracle.com       vboxdb  # Added by NetworkManager 10.0.2.15       vboxdb.oracle.com       vboxdb  # Added by NetworkManager 10.0.3.102      vboxfmw.oracle.com      vboxfmw # Added by NetworkManager 127.0.0.1       localhost.localdomain   localhost ::1     vboxdb.oracle.com       vboxdb  localhost6.localdomain6 localhost6 To make sure everything takes effect I restarted the server. Reconfiguring the Database on the DB Machine Because we changed the hostname the listener and the EM console no longer start so I need to modify the listener.ora to use the new hostname and I also need to rebuild the EM configuration because it also relies on the hostname. I edited the $ORACLE_HOME/network/admin/listener.ora and changed the listening address to the new hostname:       (ADDRESS = (PROTOCOL = TCP)(HOST = vboxdb.oracle.com)(PORT = 1521)) After changing the listener.ora I was able to start the listener using: lsnrctl start I also had to reconfigure the EM database control.  I first deconfigured it using the command: emca -deconfig dbcontrol db -repos drop This drops the repository and removes any existing registered dbcontrols. I then re-configured it using the following command: emca -config dbcontrol db -repos create This creates the EM repository and then configures and starts dbcontrol. Now my database machine is ready so I can close it down and take a snapshot. Disabling the Database on the FMW Machine I set up the database to start automatically by creating a service called “dbora”.  On the FMW machine I do not need the database running so I can prevent it auto-starting by running the following command: chkconfig –del dbora Note that because I am using a snapshot it is not a waste of disk space to have the DB installed but not used.  As long as I don’t run it, it won’t cost me anything. I can now close the FMW machine down and take a snapshot. Creating a New Domain The FMW machine is now ready to create a new domain.  When creating the domain I can point it at the second machine which is running the database.  I can potentially run these machines on two separate physical machines as long as I have the original virtual machine available to both of the physical machines. Gotchas in Snapshotting VirtualBox does not support the concept of linked machines in a network like some virtualization technologies so when creating a snapshot it is a good idea to shut both VMs down and then take a snapshot on both of them.  This is because we want to keep the database in sync with the middleware.  One way to make sure that this happens would be to place all the domain configuration files on the database server via an NFS share, this would mean that all we would need to snapshot would be the database machine because that would hold all the state and configuration. The Sky’s the Limit We have covered a simple case of having just two machines.  I have a more complicated configuration in which two machine run a RAC database off the same base OS image, and two more machines run a SOA cluster based on the same OS image.  Just remember what machine holds state and what are the consequences of taking a snapshot.

  Read the article

< Previous Page | 9 10 11 12 13 14  | Next Page >