Search Results

Search found 54080 results on 2164 pages for 'wireless access point'.

Page 13/2164 | < Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >

• How can I add a wireless router to a wired router?

  - by Tester101

  The Setup: wired D-link (EBR-2310) router connected to my cable modem. Wireless NetGear N300 (WNR2000v3) router connected to a LAN port on the wired router. What I'm trying to do: I'm trying to setup the wireless router to be a separate network, that only accesses the internet through the wired router. What I've done so far. I setup the wireless router's WAN port to get an address from ISP (which should be coming from my wired router running DHCP), and the LAN as a subnet (192.168.1). Wired router's LAN is 192.168.0. The problem: I'm not able to connect to the internet from the wireless router. At one point my wired router showed that it was handing out an IP to the wireless router, but that is not happening anymore. The question: Is what I'm trying to do possible? Am I not thinking about this properly? Do I need to buy a better wired router, with 2 WAN ports? How can I configure these routers to work together?

  Read the article

• My NetGear router suddenly started showing limited access for all wifi connected laptops

  - by Yasser

  I have netgear n300 router which I had installed about 6 months back. Here is how the setup is, I have a local internet provider by the name of "Hathway" they have this modem which is in turn connected to the router and a wire from router is connected to my desktop. As shown in this pic below, except for the laptop I use a desktop rest all the connection is same So with this connection and the below configuration, every thing worked fine. The desktop would work also all my laptops and mobile devices would connect and be able to access the internet without any problem. Now suddenly since yesterday (with no changes made whatsoever to this config) all my laptops start showing the limited connection message and cannot connect to the internet. However the desktop which is connected can access the internet. Can someone please guide me on this.

  Read the article

• Matlab Simulation: Point (symbol) Moving from start point to end point and back

  - by niko

  Hi, I would like to create an animation to demonstrate LDPC coding which is based on Sum-Product Algorithm So far I have created a graph which shows the connections between symbol nodes (left) and parity nodes (right) and would like to animate points travelling from symbol to parity nodes and back. The figure is drawn by executing the following method: function drawVertices(H) hold on; nodesCount = size(H); parityNodesCount = nodesCount(1); symbolNodesCount = nodesCount(2); symbolPoints = zeros(symbolNodesCount, 2); symbolPoints(:, 1) = 0; for i = 0 : symbolNodesCount - 1 ji = symbolNodesCount - i; scatter(0, ji) symbolPoints(i + 1, 2) = ji; end; parityPoints = zeros(parityNodesCount, 2); parityPoints(:, 1) = 10; for i = 0 : parityNodesCount - 1 ji = parityNodesCount - i; y0 = symbolNodesCount/2 - parityNodesCount/2; scatter(10, y0 + ji) parityPoints(i + 1, 2) = y0 + ji; end; axis([-1 11 -1 symbolNodesCount + 2]); axis off %connect vertices d = size(H); for i = 1 : d(1) for j = 1 : d(2) if(H(i, j) == 1) plot([parityPoints(i, 1) symbolPoints(j, 1)], [parityPoints(i, 2) symbolPoints(j, 2)]); end; end; end; So what I would like to do here is to add another method which takes start point (x and y) and end point as arguments and animates a travelling circle (dot) from start to end and back along the displayed lines. I would appreciate if anyone of you could show the solution or suggest any useful tutorial about matlab simulations. Thank you!

  Read the article

• Wireless on Inspiron 1501 not working on Ubuntu 12.04 LTS

  - by Jeek C

  As titled, I have Ubuntu 12.04 LTS on an Inspiron 1501, and the wireless has refused to work thus far. Below is what I have tried: Activating the Broadcom driver via System Settings Additional Driver Using the below commands sudo apt-get remove bcmwl-kernel-source sudo apt-get install firmware-b43-installer installing the cutter software Sadly, none of them can get the wireless working. Is there anything else I can try?

  Read the article

• Can't get Wireless RT2x00usb driver to work, and can't blacklist it

  - by TheLQ

  After a two year hiatus to Linux, I try it again out again. And then I run into to driver issues... I have an old Linksys WUSB54G v4 Wireless USB Adapter. In previous versions I had to use a combination of Ndiswrapper and Wicd to hope of getting it working. In 10.10, apparently there are built in drivers for it. Unfortunately they don't work. Fails to connect to my WPA network, fails to connect to my open unencrypted network. Wicd fails at "Obtaining IP address" or when using static IPs fails at verifying connectivity to network. Getting fed up I tried the ndiswrapper approach. Installed and configured, but still not working, even when blacklisting the rt2570 module. So for some debugging I added some lines to my /etc/modprobe.d/blacklist.conf file blacklist rt2570 blacklist prism54usb blacklist rt2x00lib blacklist rt2x00usb Restart and find this: lordquackstar@quackbeast:/etc/modprobe.d$ lsmod | grep rt2 rt2500usb 18049 0 rt2x00usb 9779 1 rt2500usb rt2x00lib 27275 2 rt2500usb,rt2x00usb led_class 2633 1 rt2x00lib mac80211 231541 2 rt2x00usb,rt2x00lib cfg80211 144470 2 rt2x00lib,mac80211 Seems to be ignored... Tried this: lordquackstar@quackbeast:/etc/modprobe.d$ sudo rmmod -f rt2x00usb ERROR: Removing 'rt2x00usb': Resource temporarily unavailable lordquackstar@quackbeast:/etc/modprobe.d$ sudo rmmod -f rt2x00lib ERROR: Removing 'rt2x00lib': Resource temporarily unavailable and couldn't connect. Restarted and was back to the same modules loading. Maybe there's something in the log: lordquackstar@quackbeast:/etc/modprobe.d$ tail -n100000 /var/log/syslog | grep rt2 Dec 13 19:01:15 quackbeast kernel: [ 23.698056] Registered led device: rt2500usb-phy0::radio Dec 13 19:01:15 quackbeast kernel: [ 23.698140] Registered led device: rt2500usb-phy0::quality Dec 13 19:01:15 quackbeast kernel: [ 23.701680] usbcore: registered new interface driver rt2500usb Dec 13 19:01:15 quackbeast NetworkManager[855]: <info> (wlan0): new 802.11 WiFi device (driver: 'rt2500usb' ifindex: 4) Dec 13 19:17:47 quackbeast kernel: [ 23.521759] Registered led device: rt2500usb-phy0::radio Dec 13 19:17:47 quackbeast kernel: [ 23.521824] Registered led device: rt2500usb-phy0::quality Dec 13 19:17:47 quackbeast kernel: [ 23.524740] usbcore: registered new interface driver rt2500usb Dec 13 19:17:47 quackbeast NetworkManager[798]: <info> (wlan0): new 802.11 WiFi device (driver: 'rt2500usb' ifindex: 4) Seems to be autoloading. So this means that even if I pull it out, remove the module, and get it working, it still won't work when its plugged in all the time. More info: lordquackstar@quackbeast:/etc/modprobe.d$ sudo lshw -C Network *SNIP* *-network description: Wireless interface physical id: 1 bus info: usb@1:2 logical name: wlan0 serial: 00:12:17:9b:f3:1e capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2500usb driverversion=2.6.35-24-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bg USB: lordquackstar@quackbeast:/etc/modprobe.d$ lsusb | grep -i rt Bus 001 Device 003: ID 13b1:000d Linksys WUSB54G v4 802.11g Adapter [Ralink RT2500USB] Any suggestions on how to either fix the rt2x00usb driver or permanently block it from loading? Note that I already have ndiswrapper installed

  Read the article

• Wireless Broadcom 4313 not working on Ubuntu 12.04

  - by user88568

  It seems a lot of people are having this problem, but none of the posted solutions have worked for me so far. My driver is installed and activated, I have tried removing and re-adding the network, and various other fixes. No networks were picked up on my first boot, the next day wireless worked fine, and since then it does not detect networks, and when I manually try to connect, it repeatedly asks for the password and does not connect. Here's my info: 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Subsystem: Dell Inspiron M5010 / XPS 8300 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f0500000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information: Len=78 Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [13c] Virtual Channel Capabilities: [160] Device Serial Number 00-00-a1-ff-ff-f3-70-f1 Capabilities: [16c] Power Budgeting Kernel driver in use: wl Kernel modules: wl, bcma, brcmsmac root@michelle-laptop:/home/michelle# ifconfig eth0 Link encap:Ethernet HWaddr 70:f1:a1:f3:ba:ab inet6 addr: fe80::72f1:a1ff:fef3:baab/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:29 TX packets:0 errors:30 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:17 eth1 Link encap:Ethernet HWaddr f0:4d:a2:53:83:7a UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:43 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:104 errors:0 dropped:0 overruns:0 frame:0 TX packets:104 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8000 (8.0 KB) TX bytes:8000 (8.0 KB) root@michelle-laptop:/home/michelle# lsmod Module Size Used by dm_crypt 22528 0 snd_hda_codec_hdmi 31775 1 snd_hda_codec_realtek 174313 1 snd_hda_intel 32765 5 snd_hda_codec 109562 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec snd_pcm 80845 4 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25424 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event parport_pc 32114 0 ppdev 12849 0 binfmt_misc 17292 1 lib80211_crypt_tkip 17275 0 bnep 17830 2 rfcomm 38139 0 snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq joydev 17393 0 wl 2646601 0 snd 62064 19 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 14635 1 snd btusb 17912 0 bluetooth 158438 11 bnep,rfcomm,btusb uvcvideo 67203 0 videodev 86588 1 uvcvideo snd_page_alloc 14108 2 snd_hda_intel,snd_pcm lib80211 14040 2 lib80211_crypt_tkip,wl intel_ips 17822 0 psmouse 72919 0 serio_raw 13027 0 mei 36570 0 dell_laptop 17767 0 dell_wmi 12601 0 dcdbas 14098 1 dell_laptop sparse_keymap 13658 1 dell_wmi mac_hid 13077 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp usbhid 41906 0 hid 77367 1 usbhid wmi 18744 1 dell_wmi i915 414817 3 atl1c 36718 0 drm_kms_helper 45466 1 i915 drm 197692 4 i915,drm_kms_helper i2c_algo_bit 13199 1 i915 video 19068 1 i915 root@michelle-laptop:/home/michelle# iwlist scan lo Interface doesn't support scanning. eth1 Interface doesn't support scanning. eth0 No scan results root@michelle-laptop:/home/michelle# rfkill list 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: dell-bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 3: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no Obviously I don't know what I'm doing. I'd appreciate any help! Thanks!

  Read the article

• Use Mobile Broadband USB as Wireless Adapter USB - HUAWEI E173

  - by Alex

  I have an Mobile Broadband USB (HUAWEI E173), which can also work as a WiFi Adapter USB. The problem is that Ubuntu 12.04 only recognizes it as an Mobile Broadband USB, not as an Wireless Adapter USB, is there a way to "trick" Ubuntu to recognize my USB as a Wireless Adapter? Thanks in advance. Notes: I used the lsusb command and got this: `Bus 002 Device 009: ID 12d1:1c23 Huawei Technologies Co., Ltd.` I have 64-bit Ubuntu Installed, so it may just be a driver problem.

  Read the article

• How can I prioritize wireless networks with network-manager

  - by kynan

  Mostly I use my laptop in an environment where different wireless networks are available and I would like to preferably connect to one of those and only fall back to the other one if that one is not available. Is there any way of prioritizing which wireless networks network-manager preferably connects to? The only workaround I found so far was unchecking Connect Automatically in the options and re-enabling it when my preferred network is not available.

  Read the article

• iwconfig, iw not displaying wireless information

  - by Srivatsa Kanchi

  after fresh install to 12.10, the wireless information is not shown by both iwconfig and iw. The wireless sets up successfully and able to connect This is what i get $ iwconfig wlan0 wlan0 IEEE 802.11abgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=14 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off $ iw wlan0 link Not connected. $ uname -a Linux srivatsa-ThinkPad-T61 3.5.0-18-generic #29-Ubuntu SMP Fri Oct 19 10:26:51 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux

  Read the article

• Wireless card unseen by lspci

  - by al-Amjad Tawfiq Isstaif

  I installed both Ubuntu 8.04 and 10.04. I tried to install the wireless card. although I succeeded in installing the driver using ndiswrapper, it tells me that the hardware is not present. When I use lspci, it doesn't list it. I have this laptop model and I think it should have the same entry about the wireless card here: http://ubuntuforums.org/showthread.php?t=1810193 Could the problem be other than hardware malfunction?

  Read the article

• can not always shutdown when wireless connection on

  - by user67362

  When the wireless connection on, I can not always shutdown my computer, always it stoped at the ubuntu interface. But if I use "sudo ifconfig wlan0 down" before shutdown, it will not happen, is there something wrong with the wireless dirver? 03:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) 09:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03)

  Read the article

• No wired and wireless connection found after upgrading 12.04

  - by ag108

  After upgrading 12.04 LTS, my wired connection works but no wireless connection found. I tried many suggestion for wireless connection on Ubuntu forum but nothing works for me. Now, maybe by mistake, I am also unable to connect Internet through wired connection. Now, (1) its says "No network devices available" and (2) in System Settings ? Hardware ? no additional driver icon is showing Please help. I don't know much about Ubuntu.

  Read the article

• Ubuntu 12.10 Broadcom Wireless BCM43225

  - by DanFritz

  During the installation of my Ubuntu 12.10 I could use the wireless connection for extra updates. After the installation I updated Ubuntu and it installed 74 new updates, after that no wireless connection (say what!). So I did try some stuff, I followed the tutorial to load the windows drivers using ndiswrapper (https://help.ubuntu.com/community/WifiDocs/Driver/Ndiswrapper) but I always get that the ndiswrapper module is not loaded (but I did install the extra 3 packages, still doesnt work). ndiswrapper-source ndiswrapper-dkms ndiswrapper-common Please somebody help! Thanks a lot

  Read the article

• Can I create an Infrastructure access point from built-in WiFi (as opposed to Ad-Hoc) on Windows XP?

  - by evilspoons

  I want to use my Windows XP laptop as an access point. What I am trying to achieve is possible under Windows 7 with a myriad of utilities, but the wireless driver stack was different before Windows 7 and those specific APIs don't exist on XP. The reason behind me wanting to do this is that I would like my Android phone to be able to connect via WiFi to a network that is only hard-wired (reverse tethering). Unfortunately, my Android device (Galaxy S Captivate) does not support ad-hoc networks without a serious amount of screwing around. Is it possible to create an "Infrastructure" network with my Dell Latitude D830's built-in WiFi - a "Dell Wireless 1395 WLAN Card", which I am assuming is probably rebadged Broadcom, or is there some fundamental difference between a wireless adapter and an access point that would prevent this?

  Read the article

• Wireless card power management

  - by penner

  I have noticed that when my computer in plugged in, the wireless strength increases. I'm assuming this is to do with power management. Is there a way to disable Wireless Power Management? I have found a few blog posts that show hacks to disable this but what is best practice here? Should there not be an option via the power menu that lets you toggle this? EDIT -- FILES AND LOGS AS REQUESTED /var/log/kern.log Jul 11 11:45:27 CoolBreeze kernel: [ 6.528052] postgres (1308): /proc/1308/oom_adj is deprecated, please use /proc/1308/oom_score_adj instead. Jul 11 11:45:27 CoolBreeze kernel: [ 6.532080] [fglrx] Gart USWC size:1280 M. Jul 11 11:45:27 CoolBreeze kernel: [ 6.532084] [fglrx] Gart cacheable size:508 M. Jul 11 11:45:27 CoolBreeze kernel: [ 6.532091] [fglrx] Reserved FB block: Shared offset:0, size:1000000 Jul 11 11:45:27 CoolBreeze kernel: [ 6.532094] [fglrx] Reserved FB block: Unshared offset:f8fd000, size:403000 Jul 11 11:45:27 CoolBreeze kernel: [ 6.532098] [fglrx] Reserved FB block: Unshared offset:3fff4000, size:c000 Jul 11 11:45:38 CoolBreeze kernel: [ 17.423743] eth1: no IPv6 routers present Jul 11 11:46:37 CoolBreeze kernel: [ 75.836426] warning: `proftpd' uses 32-bit capabilities (legacy support in use) Jul 11 11:46:37 CoolBreeze kernel: [ 75.884215] init: plymouth-stop pre-start process (2922) terminated with status 1 Jul 11 11:54:25 CoolBreeze kernel: [ 543.679614] eth1: no IPv6 routers present dmesg [ 1.411959] ACPI: Power Button [PWRB] [ 1.412046] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1 [ 1.412054] ACPI: Sleep Button [SLPB] [ 1.412150] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2 [ 1.412765] ACPI: Lid Switch [LID0] [ 1.412866] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3 [ 1.412874] ACPI: Power Button [PWRF] [ 1.412996] ACPI: Fan [FAN0] (off) [ 1.413068] ACPI: Fan [FAN1] (off) [ 1.419493] thermal LNXTHERM:00: registered as thermal_zone0 [ 1.419498] ACPI: Thermal Zone [TZ00] (27 C) [ 1.421913] thermal LNXTHERM:01: registered as thermal_zone1 [ 1.421918] ACPI: Thermal Zone [TZ01] (61 C) [ 1.421971] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 1.421986] ACPI: Battery Slot [BAT0] (battery present) [ 1.422062] ERST: Table is not found! [ 1.422067] GHES: HEST is not enabled! [ 1.422158] isapnp: Scanning for PnP cards... [ 1.422242] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 1.434620] ACPI: Battery Slot [BAT0] (battery present) [ 1.736355] Freeing initrd memory: 14352k freed [ 1.777846] isapnp: No Plug & Play device found [ 1.963650] Linux agpgart interface v0.103 [ 1.967148] brd: module loaded [ 1.968866] loop: module loaded [ 1.969134] ahci 0000:00:1f.2: version 3.0 [ 1.969154] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 1.969226] ahci 0000:00:1f.2: irq 45 for MSI/MSI-X [ 1.969277] ahci: SSS flag set, parallel bus scan disabled [ 1.969320] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 3 Gbps 0x23 impl SATA mode [ 1.969329] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ems sxs apst [ 1.969338] ahci 0000:00:1f.2: setting latency timer to 64 [ 1.983340] scsi0 : ahci [ 1.983515] scsi1 : ahci [ 1.983670] scsi2 : ahci [ 1.983829] scsi3 : ahci [ 1.983985] scsi4 : ahci [ 1.984145] scsi5 : ahci [ 1.984270] ata1: SATA max UDMA/133 abar m2048@0xf1005000 port 0xf1005100 irq 45 [ 1.984277] ata2: SATA max UDMA/133 abar m2048@0xf1005000 port 0xf1005180 irq 45 [ 1.984282] ata3: DUMMY [ 1.984285] ata4: DUMMY [ 1.984288] ata5: DUMMY [ 1.984292] ata6: SATA max UDMA/133 abar m2048@0xf1005000 port 0xf1005380 irq 45 [ 1.985150] Fixed MDIO Bus: probed [ 1.985192] tun: Universal TUN/TAP device driver, 1.6 [ 1.985196] tun: (C) 1999-2004 Max Krasnyansky <[email protected]> [ 1.985285] PPP generic driver version 2.4.2 [ 1.985472] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.985507] ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.985534] ehci_hcd 0000:00:1a.0: setting latency timer to 64 [ 1.985541] ehci_hcd 0000:00:1a.0: EHCI Host Controller [ 1.985626] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1 [ 1.985666] ehci_hcd 0000:00:1a.0: debug port 2 [ 1.989663] ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported [ 1.989690] ehci_hcd 0000:00:1a.0: irq 16, io mem 0xf1005800 [ 2.002183] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00 [ 2.002447] hub 1-0:1.0: USB hub found [ 2.002455] hub 1-0:1.0: 3 ports detected [ 2.002607] ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 2.002633] ehci_hcd 0000:00:1d.0: setting latency timer to 64 [ 2.002639] ehci_hcd 0000:00:1d.0: EHCI Host Controller [ 2.002737] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 2.002775] ehci_hcd 0000:00:1d.0: debug port 2 [ 2.006780] ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported [ 2.006806] ehci_hcd 0000:00:1d.0: irq 23, io mem 0xf1005c00 [ 2.022161] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00 [ 2.022401] hub 2-0:1.0: USB hub found [ 2.022409] hub 2-0:1.0: 3 ports detected [ 2.022567] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.022599] uhci_hcd: USB Universal Host Controller Interface driver [ 2.022720] usbcore: registered new interface driver libusual [ 2.022813] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 2.035831] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.035844] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.036096] mousedev: PS/2 mouse device common for all mice [ 2.036710] rtc_cmos 00:07: RTC can wake from S4 [ 2.036881] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0 [ 2.037143] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs [ 2.037503] device-mapper: uevent: version 1.0.3 [ 2.037656] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected] [ 2.037725] EISA: Probing bus 0 at eisa.0 [ 2.037729] EISA: Cannot allocate resource for mainboard [ 2.037734] Cannot allocate resource for EISA slot 1 [ 2.037738] Cannot allocate resource for EISA slot 2 [ 2.037741] Cannot allocate resource for EISA slot 3 [ 2.037745] Cannot allocate resource for EISA slot 4 [ 2.037749] Cannot allocate resource for EISA slot 5 [ 2.037753] Cannot allocate resource for EISA slot 6 [ 2.037756] Cannot allocate resource for EISA slot 7 [ 2.037760] Cannot allocate resource for EISA slot 8 [ 2.037764] EISA: Detected 0 cards. [ 2.037782] cpufreq-nforce2: No nForce2 chipset. [ 2.038264] cpuidle: using governor ladder [ 2.039015] cpuidle: using governor menu [ 2.039019] EFI Variables Facility v0.08 2004-May-17 [ 2.040061] TCP cubic registered [ 2.041438] NET: Registered protocol family 10 [ 2.043814] NET: Registered protocol family 17 [ 2.043823] Registering the dns_resolver key type [ 2.044290] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4 [ 2.044336] Using IPI No-Shortcut mode [ 2.045620] PM: Hibernation image not present or could not be loaded. [ 2.045644] registered taskstats version 1 [ 2.073070] Magic number: 4:976:796 [ 2.073415] rtc_cmos 00:07: setting system clock to 2012-07-11 18:45:23 UTC (1342032323) [ 2.076654] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 2.076658] EDD information not available. [ 2.302111] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2.302587] ata1.00: ATA-9: M4-CT128M4SSD2, 000F, max UDMA/100 [ 2.302595] ata1.00: 250069680 sectors, multi 16: LBA48 NCQ (depth 31/32), AA [ 2.303143] ata1.00: configured for UDMA/100 [ 2.303453] scsi 0:0:0:0: Direct-Access ATA M4-CT128M4SSD2 000F PQ: 0 ANSI: 5 [ 2.303746] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 2.303920] sd 0:0:0:0: [sda] 250069680 512-byte logical blocks: (128 GB/119 GiB) [ 2.304213] sd 0:0:0:0: [sda] Write Protect is off [ 2.304225] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.304471] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.306818] sda: sda1 sda2 < sda5 > [ 2.308780] sd 0:0:0:0: [sda] Attached SCSI disk [ 2.318162] Refined TSC clocksource calibration: 1595.999 MHz. [ 2.318169] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 2.318178] Switching to clocksource tsc [ 2.450939] hub 1-1:1.0: USB hub found [ 2.451121] hub 1-1:1.0: 6 ports detected [ 2.561786] usb 2-1: new high-speed USB device number 2 using ehci_hcd [ 2.621757] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 2.636143] ata2.00: ATAPI: TSSTcorp DVD+/-RW TS-T633C, D800, max UDMA/100 [ 2.636152] ata2.00: applying bridge limits [ 2.649711] ata2.00: configured for UDMA/100 [ 2.653762] scsi 1:0:0:0: CD-ROM TSSTcorp DVD+-RW TS-T633C D800 PQ: 0 ANSI: 5 [ 2.661486] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 2.661494] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 2.661890] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 2.662156] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 2.694649] hub 2-1:1.0: USB hub found [ 2.694840] hub 2-1:1.0: 8 ports detected [ 2.765823] usb 1-1.4: new high-speed USB device number 3 using ehci_hcd [ 2.981454] ata6: SATA link down (SStatus 0 SControl 300) [ 2.982597] Freeing unused kernel memory: 740k freed [ 2.983523] Write protecting the kernel text: 5816k [ 2.983808] Write protecting the kernel read-only data: 2376k [ 2.983811] NX-protecting the kernel data: 4424k [ 3.014594] udevd[127]: starting version 175 [ 3.068925] sdhci: Secure Digital Host Controller Interface driver [ 3.068932] sdhci: Copyright(c) Pierre Ossman [ 3.069714] sdhci-pci 0000:09:00.0: SDHCI controller found [1180:e822] (rev 1) [ 3.069742] sdhci-pci 0000:09:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 3.069786] sdhci-pci 0000:09:00.0: Will use DMA mode even though HW doesn't fully claim to support it. [ 3.069798] sdhci-pci 0000:09:00.0: setting latency timer to 64 [ 3.069816] mmc0: no vmmc regulator found [ 3.069877] Registered led device: mmc0:: [ 3.070946] mmc0: SDHCI controller on PCI [0000:09:00.0] using DMA [ 3.071078] tg3.c:v3.121 (November 2, 2011) [ 3.071252] tg3 0000:0b:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 3.071269] tg3 0000:0b:00.0: setting latency timer to 64 [ 3.071403] firewire_ohci 0000:09:00.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [ 3.071417] firewire_ohci 0000:09:00.3: setting latency timer to 64 [ 3.078509] EXT4-fs (sda1): INFO: recovery required on readonly filesystem [ 3.078517] EXT4-fs (sda1): write access will be enabled during recovery [ 3.110417] tg3 0000:0b:00.0: eth0: Tigon3 [partno(BCM95784M) rev 5784100] (PCI Express) MAC address b8:ac:6f:71:02:a6 [ 3.110425] tg3 0000:0b:00.0: eth0: attached PHY is 5784 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0]) [ 3.110431] tg3 0000:0b:00.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1] [ 3.110436] tg3 0000:0b:00.0: eth0: dma_rwctrl[76180000] dma_mask[64-bit] [ 3.125492] firewire_ohci: Added fw-ohci device 0000:09:00.3, OHCI v1.10, 4 IR + 4 IT contexts, quirks 0x11 [ 3.390124] EXT4-fs (sda1): orphan cleanup on readonly fs [ 3.390135] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078710 [ 3.390232] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 2363071 [ 3.390327] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078711 [ 3.390350] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078709 [ 3.390367] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078708 [ 3.390384] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078707 [ 3.390401] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078706 [ 3.390417] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078705 [ 3.390435] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078551 [ 3.390452] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078523 [ 3.390470] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078520 [ 3.390487] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7077901 [ 3.390551] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4063272 [ 3.390562] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4063266 [ 3.390572] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4063261 [ 3.390582] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4063256 [ 3.390592] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4063255 [ 3.390602] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 2363072 [ 3.390620] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 2360050 [ 3.390698] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 5250064 [ 3.390710] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 2365394 [ 3.390728] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 2365390 [ 3.390745] EXT4-fs (sda1): 22 orphan inodes deleted [ 3.390748] EXT4-fs (sda1): recovery complete [ 3.397636] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 3.624910] firewire_core: created device fw0: GUID 464fc000110e2661, S400 [ 3.927467] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 3.929965] udevd[400]: starting version 175 [ 3.933581] Adding 6278140k swap on /dev/sda5. Priority:-1 extents:1 across:6278140k SS [ 3.945183] lp: driver loaded but no devices found [ 3.999389] wmi: Mapper loaded [ 4.016696] ite_cir: Auto-detected model: ITE8708 CIR transceiver [ 4.016702] ite_cir: Using model: ITE8708 CIR transceiver [ 4.016706] ite_cir: TX-capable: 1 [ 4.016710] ite_cir: Sample period (ns): 8680 [ 4.016713] ite_cir: TX carrier frequency (Hz): 38000 [ 4.016716] ite_cir: TX duty cycle (%): 33 [ 4.016719] ite_cir: RX low carrier frequency (Hz): 0 [ 4.016722] ite_cir: RX high carrier frequency (Hz): 0 [ 4.025684] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. [ 4.025691] Disabling lock debugging due to kernel taint [ 4.027410] IR NEC protocol handler initialized [ 4.030250] lib80211: common routines for IEEE802.11 drivers [ 4.030257] lib80211_crypt: registered algorithm 'NULL' [ 4.036024] IR RC5(x) protocol handler initialized [ 4.036092] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 4.036188] snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X [ 4.036307] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 4.036361] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness [ 4.039006] acpi device:03: registered as cooling_device10 [ 4.039164] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input5 [ 4.039261] ACPI: Video Device [M86] (multi-head: yes rom: no post: no) [ 4.049753] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 4.050201] wl 0000:05:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 4.050215] wl 0000:05:00.0: setting latency timer to 64 [ 4.052252] Registered IR keymap rc-rc6-mce [ 4.052432] input: ITE8708 CIR transceiver as /devices/virtual/rc/rc0/input6 [ 4.054614] IR RC6 protocol handler initialized [ 4.054787] rc0: ITE8708 CIR transceiver as /devices/virtual/rc/rc0 [ 4.054839] ite_cir: driver has been successfully loaded [ 4.057338] IR JVC protocol handler initialized [ 4.061553] IR Sony protocol handler initialized [ 4.066578] input: MCE IR Keyboard/Mouse (ite-cir) as /devices/virtual/input/input7 [ 4.066724] IR MCE Keyboard/mouse protocol handler initialized [ 4.072580] lirc_dev: IR Remote Control driver registered, major 250 [ 4.073280] rc rc0: lirc_dev: driver ir-lirc-codec (ite-cir) registered at minor = 0 [ 4.073286] IR LIRC bridge handler initialized [ 4.077849] Linux video capture interface: v2.00 [ 4.079402] uvcvideo: Found UVC 1.00 device Laptop_Integrated_Webcam_2M (0c45:640f) [ 4.085492] EDAC MC: Ver: 2.1.0 [ 4.087138] lib80211_crypt: registered algorithm 'TKIP' [ 4.091027] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8 [ 4.091733] snd_hda_intel 0000:02:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 4.091826] snd_hda_intel 0000:02:00.1: irq 47 for MSI/MSI-X [ 4.091861] snd_hda_intel 0000:02:00.1: setting latency timer to 64 [ 4.093115] EDAC i7core: Device not found: dev 00.0 PCI ID 8086:2c50 [ 4.112448] HDMI status: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0 [ 4.112612] input: HD-Audio Generic HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/0000:02:00.1/sound/card1/input9 [ 4.113311] type=1400 audit(1342032325.540:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=658 comm="apparmor_parser" [ 4.114501] type=1400 audit(1342032325.540:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=658 comm="apparmor_parser" [ 4.115253] type=1400 audit(1342032325.540:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=658 comm="apparmor_parser" [ 4.121870] input: Laptop_Integrated_Webcam_2M as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.4/1-1.4:1.0/input/input10 [ 4.122096] usbcore: registered new interface driver uvcvideo [ 4.122100] USB Video Class driver (1.1.1) [ 4.128729] [fglrx] Maximum main memory to use for locked dma buffers: 5840 MBytes. [ 4.129678] [fglrx] vendor: 1002 device: 68c0 count: 1 [ 4.131991] [fglrx] ioport: bar 4, base 0x2000, size: 0x100 [ 4.132015] pci 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 4.132024] pci 0000:02:00.0: setting latency timer to 64 [ 4.133712] [fglrx] Kernel PAT support is enabled [ 4.133747] [fglrx] module loaded - fglrx 8.96.4 [Mar 12 2012] with 1 minors [ 4.162666] eth1: Broadcom BCM4727 802.11 Hybrid Wireless Controller 5.100.82.38 [ 4.184133] device-mapper: multipath: version 1.3.0 loaded [ 4.196660] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [ 4.279897] input: Dell WMI hotkeys as /devices/virtual/input/input11 [ 4.292402] Bluetooth: Core ver 2.16 [ 4.292449] NET: Registered protocol family 31 [ 4.292454] Bluetooth: HCI device and connection manager initialized [ 4.292459] Bluetooth: HCI socket layer initialized [ 4.292463] Bluetooth: L2CAP socket layer initialized [ 4.292473] Bluetooth: SCO socket layer initialized [ 4.296333] Bluetooth: RFCOMM TTY layer initialized [ 4.296342] Bluetooth: RFCOMM socket layer initialized [ 4.296345] Bluetooth: RFCOMM ver 1.11 [ 4.313586] ppdev: user-space parallel port driver [ 4.316619] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 4.316625] Bluetooth: BNEP filters: protocol multicast [ 4.383980] type=1400 audit(1342032325.812:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=938 comm="apparmor_parser" [ 4.385173] type=1400 audit(1342032325.812:6): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=938 comm="apparmor_parser" [ 4.425757] init: failsafe main process (898) killed by TERM signal [ 4.477052] type=1400 audit(1342032325.904:7): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1011 comm="apparmor_parser" [ 4.477592] type=1400 audit(1342032325.904:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=1010 comm="apparmor_parser" [ 4.478099] type=1400 audit(1342032325.904:9): apparmor="STATUS" operation="profile_load" name="/usr/sbin/tcpdump" pid=1017 comm="apparmor_parser" [ 4.479233] type=1400 audit(1342032325.904:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1014 comm="apparmor_parser" [ 4.510060] vesafb: mode is 1152x864x32, linelength=4608, pages=0 [ 4.510065] vesafb: scrolling: redraw [ 4.510071] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 [ 4.510084] mtrr: no more MTRRs available [ 4.513081] vesafb: framebuffer at 0xd0000000, mapped to 0xf9400000, using 3904k, total 3904k [ 4.515203] Console: switching to colour frame buffer device 144x54 [ 4.515278] fb0: VESA VGA frame buffer device [ 4.590743] tg3 0000:0b:00.0: irq 48 for MSI/MSI-X [ 4.702009] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 4.704409] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 4.978379] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000 [ 5.030104] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input12 [ 5.045782] kvm: VM_EXIT_LOAD_IA32_PERF_GLOBAL_CTRL does not work properly. Using workaround [ 5.519573] [fglrx] ATIF platform detected with notification ID: 0x81 [ 6.391466] fglrx_pci 0000:02:00.0: irq 49 for MSI/MSI-X [ 6.393137] [fglrx] Firegl kernel thread PID: 1305 [ 6.393306] [fglrx] Firegl kernel thread PID: 1306 [ 6.393472] [fglrx] Firegl kernel thread PID: 1307 [ 6.393726] [fglrx] IRQ 49 Enabled [ 6.528052] postgres (1308): /proc/1308/oom_adj is deprecated, please use /proc/1308/oom_score_adj instead. [ 6.532080] [fglrx] Gart USWC size:1280 M. [ 6.532084] [fglrx] Gart cacheable size:508 M. [ 6.532091] [fglrx] Reserved FB block: Shared offset:0, size:1000000 [ 6.532094] [fglrx] Reserved FB block: Unshared offset:f8fd000, size:403000 [ 6.532098] [fglrx] Reserved FB block: Unshared offset:3fff4000, size:c000 [ 17.423743] eth1: no IPv6 routers present [ 75.836426] warning: `proftpd' uses 32-bit capabilities (legacy support in use) [ 75.884215] init: plymouth-stop pre-start process (2922) terminated with status 1 [ 543.679614] eth1: no IPv6 routers present lsmod Module Size Used by kvm_intel 127560 0 kvm 359456 1 kvm_intel joydev 17393 0 vesafb 13516 1 parport_pc 32114 0 bnep 17830 2 ppdev 12849 0 rfcomm 38139 0 bluetooth 158438 10 bnep,rfcomm dell_wmi 12601 0 sparse_keymap 13658 1 dell_wmi binfmt_misc 17292 1 dell_laptop 17767 0 dcdbas 14098 1 dell_laptop dm_multipath 22710 0 fglrx 2909855 143 snd_hda_codec_hdmi 31775 1 psmouse 72919 0 serio_raw 13027 0 i7core_edac 23382 0 lib80211_crypt_tkip 17275 0 edac_core 46858 1 i7core_edac uvcvideo 67203 0 snd_hda_codec_idt 60251 1 videodev 86588 1 uvcvideo ir_lirc_codec 12739 0 lirc_dev 18700 1 ir_lirc_codec ir_mce_kbd_decoder 12681 0 snd_seq_midi 13132 0 ir_sony_decoder 12462 0 ir_jvc_decoder 12459 0 snd_rawmidi 25424 1 snd_seq_midi ir_rc6_decoder 12459 0 wl 2646601 0 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event ir_rc5_decoder 12459 0 video 19068 0 snd_hda_intel 32765 5 snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq snd_hda_codec 109562 3 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_hda_intel rc_rc6_mce 12454 0 lib80211 14040 2 lib80211_crypt_tkip,wl snd_hwdep 13276 1 snd_hda_codec ir_nec_decoder 12459 0 snd_pcm 80845 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec ite_cir 24743 0 rc_core 21263 10 ir_lirc_codec,ir_mce_kbd_decoder,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_rc5_decoder,rc_rc6_mce,ir_nec_decoder,ite_cir snd_timer 28931 2 snd_seq,snd_pcm wmi 18744 1 dell_wmi snd 62064 20 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_rawmidi,snd_seq,snd_seq_device,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_timer mac_hid 13077 0 soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm coretemp 13269 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp tg3 141369 0 firewire_ohci 40172 0 sdhci_pci 18324 0 firewire_core 56906 1 firewire_ohci sdhci 28241 1 sdhci_pci crc_itu_t 12627 1 firewire_core lshw *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 logical name: eth1 version: 01 serial: 70:f1:a1:a9:54:31 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 ip=192.168.0.117 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0900000-f0903fff *-network description: Ethernet interface product: NetLink BCM5784M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:0b:00.0 logical name: eth0 version: 10 serial: b8:ac:6f:71:02:a6 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 firmware=sb v2.19 latency=0 link=no multicast=yes port=twisted pair resources: irq:48 memory:f0d00000-f0d0ffff

  Read the article

• Enable wireless on Dell Inspiron 1300

  - by Simon

  As per subject, I've looked at various resources and attempted ndiswrapper solutions, found a one-click solution that lead to a 404 and this but none works. I've run all updates. Once I managed to lose my wired connection as well and had to reinstall. This is my first hour with Linux. iwconfig gives this before I do anything: lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on eth0 no wireless extens Thanks for responding lspci returns 00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03) (prog-if 00 [VGA controller]) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at dff00000 (32-bit, non-prefetchable) [size=512K] Region 1: I/O ports at eff8 [size=8] Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M] Region 3: Memory at dfec0000 (32-bit, non-prefetchable) [size=256K] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: i915 Kernel modules: intelfb, i915 00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at dff80000 (32-bit, non-prefetchable) [size=512K] Capabilities: <access denied> 00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 42 Region 0: Memory at dfebc000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0 I/O behind bridge: 00002000-00002fff Memory behind bridge: 30000000-301fffff Prefetchable memory behind bridge: 0000000030200000-00000000303fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 4 (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=0c, subordinate=0d, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: dfc00000-dfdfffff Prefetchable memory behind bridge: 00000000d0000000-00000000d01fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at bf80 [size=32] Kernel driver in use: uhci_hcd 00:1d.1 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 17 Region 4: I/O ports at bf60 [size=32] Kernel driver in use: uhci_hcd 00:1d.2 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at bf40 [size=32] Kernel driver in use: uhci_hcd 00:1d.3 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 19 Region 4: I/O ports at bf20 [size=32] Kernel driver in use: uhci_hcd 00:1d.7 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03) (prog-if 20 [EHCI]) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at b0000000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d3) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 0000f000-00000fff Memory behind bridge: dfb00000-dfbfffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 03) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Kernel modules: iTCO_wdt, intel-rng 00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 03) (prog-if 8a [Master SecP PriP]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at bfa0 [size=16] Kernel driver in use: ata_piix 02:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 18 Region 0: Memory at dfbfc000 (32-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: b44 Kernel modules: b44 02:03.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02) Subsystem: Dell Wireless 1370 WLAN Mini-PCI Card Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 17 Region 0: Memory at dfbfe000 (32-bit, non-prefetchable) [size=8K] Kernel driver in use: b43-pci-bridge Kernel modules: ssb and the rfkill shows 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Just checking addtional drivers. Says no additional driver installed in this system

  Read the article

• Wireless Activity Monitoring for PCI DSS Compliance

  - by dkusleika

  In an effort to be PCI DSS compliant, I took a trustkeeper.net questionnaire. I failed the question that asks Is the presence of wireless access points tested for by using a wireless analyzer at least quarterly or by deploying a wireless IDS/IPS to identify all wireless devices in use? (SAQ #11.1) My only wireless access point is outside my firewall, so even if you cracked my wireless you couldn't get inside my domain (unless you crack that too). My firewall doesn't have IPS and I couldn't tell if it had IDS. I looked around for a wireless analyzer, but what I found was $500, which is a little pricey for my size business. And even if I got it, I'm not sure I would understand what it tells me. Surely there are smaller/less sophisticated businesses that take credit cards and have solved this. My questions are: What are the risks if someone were to crack my wireless? (Could they read all internet traffic? Just wireless traffic? Just use my internet connection?) And what is the best/cheapest way to test my connection point quarterly? Should I buy the $500 analyzer? Domain is Windows Server 2000. Firewall is Sonicwall Pro 2040. Router is 8 port D-link.

  Read the article

• WiFi connected to router, but no internet connection

  - by Quetzacotl

  I just got a new notebook, a ThinkPad Edge E530, and installed Ubuntu on it. I'm pretty new to Ubuntu. On the same laptop, running Windows 7, the Wi-Fi connection works fine. Ethernet connection works both on Win7 and on Ubuntu. Only Wi-Fi on Ubuntu does not work; it connects to the Wi-Fi access point but I don't have Internet access. My wireless card is Intel Centrino Wireless-N 2230. What can fix the problem? EDIT: ifconfig -a eth0 Link encap:Ethernet HWaddr b8:88:e3:30:72:34 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:43 Base address:0x8000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:163 errors:0 dropped:0 overruns:0 frame:0 TX packets:163 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:10124 (10.1 KB) TX bytes:10124 (10.1 KB) usb0 Link encap:Ethernet HWaddr 02:15:e0:ec:01:00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 68:5d:43:43:71:e1 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::6a5d:43ff:fe43:71e1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:40 errors:0 dropped:0 overruns:0 frame:0 TX packets:220 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2801 (2.8 KB) TX bytes:26230 (26.2 KB) route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 192.168.2.0 0.0.0.0 255.255.255.0 U 2 0 0 wlan0 cat /etc/resolv.conf # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN nameserver 127.0.0.1 iwconfig lo no wireless extensions. usb0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"SATELITE" Mode:Managed Frequency:2.462 GHz Access Point: 00:1F:1F:8D:CC:08 Bit Rate=1 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=60/70 Signal level=-50 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:93 Invalid misc:243 Missed beacon:0 eth0 no wireless extensions.

  Read the article

• Windows 7 wireless not seeing any networks

  - by jkohlhepp

  I think I have managed to confuse Windows 7. When I did the install, I had the network cable plugged in to my router, but the wireless card was also enabled. During the install, Windows 7 seemed to see my wireless network and even asked me for the WEP key. I know that it used the WEP key because I initially entered an invalid one and it gave me an error. Then the network said "SoAndSoWireless Connected". However, when I unplug or disable my wired network card, then I have no internet, and it can't see any networks. When I plug in the wired network card, it says "SoAndSoWireless Connected". Under Network and Internet Network Connections I have "Local Area Connection" and "Wireless Network Connection". The wired one's status is "SoAndSoWireless" and the wireless status is "Not Connected". Also, the wireless connection can't seem to see any other wireless networks in the area and I know there are tons. My neighbors have several. I've somehow seemingly confused Windows 7 into thinking that my wired network card is my wireless card or something. Any ideas on how to un-confuse it? This is a desktop machine by the way, if it matters. EDIT: Ah, I think part of the problem is that I named my network accidentally the same as the name of the wireless network being broadcast by the wireless router. So that might be why it says that name on the hard-wired connection. Perhaps the drivers just are completely not working for the wireless card. Thanks, ~ Justin

  Read the article

• Improving abysmal 802.11n wireless network

  - by concept

  I am in desperate need of help to improve the abysmal performance of my 802.11n wireless network. At best I get 30Mbs (this is an internet download) from a technology that boasts 300Mbs, even worse is the LAN where to date best i have ever gotten is 1Mbs. It is literally quicker to copy the file to a USB and walk it to the other computer. Infrastructure is this AP 802.11n only broadcasting at both 2.4GHz and 5GHz Mac with 802.11a/b/g/n card is connected to the AP via 5GHz Linux with 802.11a/b/g/n card is connected to AP via 2.4GHz I have conducted the following tests (results at end of post) Internet based speed test wired and wireless LAN file copy wired and wireless I have read: http://nutsaboutnets.com/troubleshooting-wi-fi-problems/ http://www.smallnetbuilder.com/wireless/wireless-basics/30664-5-ways-to-fix-slow-80211n-- speed http colon //www.wi-fiplanet dot com/tutorials/7-tips-to-increase-wi-fi-performance.html Slow file transfer on network between two 802.11n laptops (connected directly together via access point) Wireless Network Performance Issues Slower than expected 802.11n wireless network speeds I have made the following optimizations AP broadcasts only 802.11n on both 2.4GHz and 5GHz frequencies 2.4GHz is on a channel with least interference (live in an apartment with lots of APs), this did make a 10Mb/sec improvement Our AP is the only one transmitting on the 5GHz freq. Security: WPA Personal WPA2 AES encryption Bandwidth: 20MHz / 40MHz (i assume this to be channel bonding) I have tried the following with 0 improvement Dropped the Fragment Threshold to 512 Dropped the Request To Send (RTS) Threshold to 512 and 1 Even thought of buying a frequency spectrum analyzer, until i saw the cost of them!!! Speed test results Linux Wired: DOWNLOAD 128.40Mb/s UPLOAD 10.62Mb/s www dot speedtest dot net/my-result/2948381853 Mac Wired: DOWNLOAD 118.02Mb/s UPLOAD 10.56Mb/s www dot speedtest dot net/my-result/2948384406 Linux Wireless: DOWNLOAD 23.99Mb/s UPLOAD 10.31Mb/s www.speedtest dot net/my-result/2948394990 Mac Wireless: DOWNLOAD 22.55Mb/s UPLOAD 10.36Mb/s www.speedtest dot net/my-result/2948396489 LAN NFS 53,345,087 bytes (51Mb) file Linux Mac NFS Wired: 65.6959 Mb/sec Linux Mac NFS Wireless: .9443 Mb/sec All help is appreciated, even testing methods will be accepted.

  Read the article

• 2nd/3rd version of wireless network appears

  - by neildeadman

  I replaced an old SpeedTouch ADSL router with a Netgear DG384 that I have and whilst doing so decided to change the wireless password. For this question assume my wireless network SSID is DeddersHome. On my netbook and macbook pro (running Win7) it won't connect to the Internet. When I hover over the tray icon for wireless it says "DeddersHome 2" and "DeddersHome 3" have no internet connection. What are these additional wireless networks? I can't see them in the wireless network list on any wireless device I have. Wired connections and wireless through my iPhone work fine. I saw this before with the SpeedTouch, but it just went away!! I also have one Apple AirPort Express connected to the wireless network which my Xbox is connected to (wired). This all worked before... I am going to remove AirPort to see if it is this causing the problem, but thought I'd ask the question to give it time for an answer whilst I continue to search. Cheers

  Read the article

• Wireless N extend G range?

  - by Sam

  I've searched all over the internet for an answer to this and I can't find one. If I purchase a wireless N router, with greater range than my current G router will the range of the wireless G signal go as far as the wireless N signal? I say this because Wireless N routers are supposed to be compatible with wireless G devices. Is the wireless G a lesser signal coming out of the router? Sorry if I confused you, I am a little confused myself.

  Read the article

• Windows 7 - saved wifi access points disappear from list

  - by KáGé

  I'm having a weird issue with Windows 7 x64: I'm moving my notebook between two locations weekly, at each I have a wifi router. They both have hidden SSID-s, which are different. If I save one, the other one gets deleted from the list, as if overwritten, so I always have to retype the SSID and password, if I want to connect after moving my computer. At first I tought the problem was caused by both routers having the same password, but after I changed one (suffixed it with "_2") it persisted. What can I do about this? Thanks.

  Read the article

• crash when using wireless network

  - by Erik

  ubuntu 12.04 32 bit When I start up my system almost instantly freezes, I found that the problem lays with my wireless network, because the crash is always t the same time as the message that tells me I am connected to a network when I start up connected to a cable everything works fine, I can even see that I am connected to our wireless network, until I unplug the ethernet cable, then it all freezes again the same happened when I boot from a live cd (from usb) The problem only occurs on my netbook, my laptop doesn't give any problems. I don't know if anyone else has had similar problems, or if anyone knows a solution... Thanks in advance! greetings Erik EDIT (21/3/2012): it seems there is some external factor involved, I'm using my netbook for about 50 minutes now while connected to the wireless network, and still it didn't crash strange enough, before these 50 minutes I had to put it down by holding the power button, because I decided to try it again, that time it did crash... before (while connected with an ethernet cable) I've been trying to get my Bluetooth working, that didn't succeed entirely, but I guess that might be a factor in the question why it doesn't crash at the moment now I rebooted, connected, and no crash... if it crashes again, I'll update this post again. in the meantime, if anyone has an idea on what could be a factor, and on how to create a crash using that factor, feel free to ask!

  Read the article

• Network really slow with TL-WN951N wireless card

  - by Sam

  I literally just installed ubuntu and it seems to be working great except the network is deadly slow. I'm running a TL-WN951N wireless card which can download at about 600-700 KB/s in windows but in Ubuntu the max speed it seems to get is around 5KB/s. I guess I should note that my WAP is only wireless-G but like I said, I can get much better speeds in Windows. I'm testing the speeds by downloading files from here: http://mirror.internode.on.net/pub/test/ Anyone have any idea? I saw some people recommend downloading drivers and compiling them myself but I'm really really new to all of this so would appreciate someone babying me through it so I don't brick my computer! Here are the results of lspci -v: 04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) Subsystem: Giga-byte Technology GA-EP45-DS5 Motherboard Flags: bus master, fast devsel, latency 0, IRQ 44 I/O ports at c000 [size=256] Memory at e9110000 (64-bit, prefetchable) [size=4K] Memory at e9100000 (64-bit, prefetchable) [size=64K] [virtual] Expansion ROM at e9120000 [disabled] [size=64K] Capabilities: <access denied> Kernel driver in use: r8169 Kernel modules: r8169 05:02.0 Network controller: Atheros Communications Inc. AR5008 Wireless Network Adapter (rev 01) Subsystem: Atheros Communications Inc. Device 3071 Flags: bus master, 66MHz, medium devsel, latency 168, IRQ 18 Memory at e9200000 (32-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: ath9k Kernel modules: ath9k

  Read the article

< Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >