Search Results

Search found 54080 results on 2164 pages for 'wireless access point'.

Page 18/2164 | < Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >

  • installed ubuntu 12.04 and no wireless internet at all

    - by Memoq
    I'm extremely new to ubuntu. I installed 12.04 on a laptop that had no os. I've tried following these forums to troubleshoot my internet problems only to be confused by all the steps. I need help. I'm willing to follow any instruction as long as they make sense. Any help would be nice. The equipment i have is a Dell inspiron 1100 laptop wireless card is D link 2.4 dwl -g650 product ar5212/ar5313

    Read the article

  • Looking for wireless product

    - by Belinda
    Can anyone suggest some options for me? I would like to provide our maintenance department with a view-only monitor showing our common Outlook calendars. I'm guessing it would have to have some touch-screen capabilities since they would need to be able to toggle between several calendars. We do have a cobbled together, building wide wireless network. I don't want anything that needs to be "wired or cabled" just plugged into a power source and mounted on the wall.

    Read the article

  • Broadcom device 4365 wireless driver for 12.04

    - by NilPointer
    My laptop (Dell Inspiron 17R 5720) came with preinstalled Ubuntu 11.10. I removed it and installed 12.04. Now I can't find driver for wireless. Apparently, in 11.10 there was Broadcom-STA driver. But in 12.04 there is no additional drivers to install. I tried using: sudo m-a a-i broadcom-sta But building fails on 26%. How can I install driver According to lspci i got: Broadcom Corporation Device 4365 (rev 01)

    Read the article

  • Ubuntu, No wireless networks found after correctly installed madwifi

    - by Peter
    Hi, I just installed madwifi on my MSI laptop with an Atheros AR5001 wifi card & Lucid. As far as I can see and according to System - Administration - Hardware drivers the install was successful and the card + driver is up and running. However, I don't see any wireless network (my windows PC can see about 5 wireless networks). I tried it with the network manager applet as well as with wicd. If I try to connect to "Hidden Wireless Network" via nm-applet, it will start to connect for a while but is unable too (although I supply it with the correct WEP settings & key) So, I'm unable to use my wireless network. What am i doing wrong? Some information about my system: iwconfig lo no wireless extensions. eth0 no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11g ESSID:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:17 dBm Sensitivity=1/1 Retry:off RTS thr:off Fragment thr:off Power Management:off Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 pan0 no wireless extensions. ifconfig ath0 Link encap:Ethernet HWaddr 00:15:af:cf:e2:ca inet6 addr: fe80::215:afff:fecf:e2ca/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 00:21:85:4d:82:78 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::221:85ff:fe4d:8278/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3800 errors:0 dropped:0 overruns:0 frame:0 TX packets:2944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3940261 (3.9 MB) TX bytes:525218 (525.2 KB) Interrupt:27 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) wifi0 Link encap:UNSPEC HWaddr 00-15-AF-CF-E2-CA-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3497 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:280 RX bytes:0 (0.0 B) TX bytes:179947 (179.9 KB) Interrupt:16 lshw -C network *-network description: Wireless interface product: AR5001 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wifi0 version: 01 serial: 00:15:af:cf:e2:ca width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci latency=0 multicast=yes wireless=IEEE 802.11g resources: irq:16 memory:fd7f0000-fd7fffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 01 serial: 00:21:85:4d:82:78 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.101 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:27 ioport:c800(size=256) memory:fe2ff000-fe2fffff memory:fe2c0000-fe2dffff(prefetchable) lspci 00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) 00:04.0 PCI bridge: ATI Technologies Inc Device 7914 00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) 00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3) 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller 02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 06:04.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 21) 06:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 06:04.3 Bridge: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 06:04.4 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) less /proc/modules | grep ath ath_rate_sample 11476 1 - Live 0xf812b000 ath_pci 193197 0 - Live 0xf85c3000 wlan 222892 5 wlan_wep,wlan_scan_sta,ath_rate_sample,ath_pci, Live 0xf8537000 ath_hal 398604 3 ath_rate_sample,ath_pci, Live 0xf8480000 I've been at this for hours now, also tried ndiswrapper and ath5k drivers with no luck, and really could use some help. Cheers.

    Read the article

  • How can we connect TP-link Access Point- TL-WA5210G with Wifi Lan card?

    - by PPS
    I would like to know that, We have a small Wireless Network that covers 40 mtrs indoor. Now we plan to expand our Network Coverage area apporx. 200 Mtrs (Outdoor). Due to our requirement we used TP- Link Access Point TL-WA5210G Outdoor(This AP covers 15Km area). We have 3 blocks between 200 mtrs, We like to connect all the laptops Lan Card directly with required Access-point. What should we do to achieve this, right now we are not getting the full strength signal, when we cross the 80 mtrs. So please suggest me proper configuration for implementing this TP-Link access point. Thanks PPS

    Read the article

  • Cannot find wireless driver for HP laptop

    - by rodey
    I have an HP laptop (model: dv7-1267cl, Windows 7 64-bit Home Premium) and I cannot find the wireless driver for the laptop. I am need of a different version because my wireless connection under Windows is flaky and unreliable. I have problems printing to my wireless printer and logging in to and using several sites like reddit.com, phoenix.edu and facebook.com - I get several "page cannot be displayed" messages while using my wireless connection. I disable my wireless adapter and use an ethernet cable and it all works fine. I also used an Ubuntu Live CD to confirm that there is not a problem with the hardware. This is software/driver issue. The drivers were auto installed by the OS. The Device Manager shows the wireless adapter as Atheros AR5009 802.11 a/g/n WiFi Adapter. I have checked the HP website for my laptop and they do not have wireless drivers listed for that model wireless adapter. I have also checked with atheros.com and I do not see my model adapter on their list of available hardware. Device Manager lists the Hardware ID's for my adapter as: PCI\VEN_168C&DEV_002A&SUBSYS_1381103C&REV_01 PCI\VEN_168C&DEV_002A&SUBSYS_1381103C PCI\VEN_168C&DEV_002A&CC_028000 PCI\VEN_168C&DEV_002A&CC_0280 A search for the first Hardware ID turned up this question from experts-exchange.com. tl;dr A driver does not exist for that model adapter.

    Read the article

  • Intel Dual Band Wireless-AC 7260 keeps dropping wifi

    - by Rick T
    My wifi Intel Dual Band Wireless-AC 7260 keeps dropping wificonnection drops and the network to which I was connected disappears from the list of available networks in network manager. The only way to fix it is to disable wifi and re-enable it How can I fix this. I'm using ubuntu 14.04 64bit. It mostly drops connections on the 5ghz network. My other devices don't drop connections over wifi. see logs and versions rt@simon:~$ uname -a Linux simon 3.13.0-34-generic #60-Ubuntu SMP Wed Aug 13 15:45:27 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux rt@simon:~$ rt@simon:~$ dmesg | grep iwl [ 3.370777] iwlwifi 0000:03:00.0: irq 46 for MSI/MSI-X [ 3.381089] iwlwifi 0000:03:00.0: loaded firmware version 22.24.8.0 op_mode iwlmvm [ 3.414637] iwlwifi 0000:03:00.0: Detected Intel(R) Dual Band Wireless AC 7260, REV=0x144 [ 3.414695] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 3.414913] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 3.630208] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs' [ 9.304838] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 9.305068] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 605.483174] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 605.483396] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S rt@simon:~$ cat /var/log/syslog | grep -e iwl -e 80211 | tail -n25 Aug 14 08:13:02 simon kernel: [ 3.452780] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:13:02 simon kernel: [ 3.630208] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs' Aug 14 08:13:06 simon NetworkManager[1125]: <info> rfkill1: found WiFi radio killswitch (at /sys/devices/pci0000:00/0000:00:1c.2/0000:03:00.0/ieee80211/phy0/rfkill1) (driver iwlwifi) Aug 14 08:13:06 simon NetworkManager[1125]: <info> (wlan0): using nl80211 for WiFi device control Aug 14 08:13:06 simon NetworkManager[1125]: <info> (wlan0): new 802.11 WiFi device (driver: 'iwlwifi' ifindex: 3) Aug 14 08:13:06 simon kernel: [ 9.304838] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S Aug 14 08:13:06 simon kernel: [ 9.305068] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S Aug 14 08:14:18 simon kernel: [ 81.230162] cfg80211: Calling CRDA to update world regulatory domain Aug 14 08:14:18 simon kernel: [ 81.232330] cfg80211: World regulatory domain updated: Aug 14 08:14:18 simon kernel: [ 81.232332] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) Aug 14 08:14:18 simon kernel: [ 81.232333] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:14:18 simon kernel: [ 81.232334] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:14:18 simon kernel: [ 81.232335] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Aug 14 08:14:18 simon kernel: [ 81.232336] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:14:18 simon kernel: [ 81.232337] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:23:02 simon kernel: [ 605.483174] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S Aug 14 08:23:02 simon kernel: [ 605.483396] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S Aug 14 08:23:18 simon kernel: [ 621.223905] cfg80211: Calling CRDA to update world regulatory domain Aug 14 08:23:18 simon kernel: [ 621.228945] cfg80211: World regulatory domain updated: Aug 14 08:23:18 simon kernel: [ 621.228950] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) Aug 14 08:23:18 simon kernel: [ 621.228954] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:23:18 simon kernel: [ 621.228956] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:23:18 simon kernel: [ 621.228959] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Aug 14 08:23:18 simon kernel: [ 621.228961] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:23:18 simon kernel: [ 621.228963] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

    Read the article

  • Wireless is detected, but not connecting. Ethernet works. How to correct the wireless address?

    - by Lucas
    I am running Ubuntu 14.04 with cable internet, and my wireless is detected and connected, but I cannot connect to the internet. I know the problem is with my machine because other machines are connecting to the same router just fine. I can connect via ethernet just fine as well. Here are some notable tests: ping 192.168.0.105 works with 0% packet loss, but ping 192.168.0.1 has 100% packet loss. When I plug in my ethernet, ping 192.168.0.1 works with 0% packet loss. My wireless name is tg, and the router ip is 192.168.0.1 (where I can enter username and password). I suspect that I need to change my wireless address from 192.168.0.105 to 192.168.0.1. Any suggestions on how to proceed? extra info: [lucas@lucas-ThinkPad-W520]/home/lucas$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"tg" Mode:Managed Frequency:2.462 GHz Access Point: 00:02:6F:83:F8:F4 Bit Rate=1 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=62/70 Signal level=-48 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:52 Invalid misc:166 Missed beacon:0 [lucas@lucas-ThinkPad-W520]/home/lucas$ ifconfig eth0 Link encap:Ethernet HWaddr f0:de:f1:b2:53:53 inet addr:192.168.0.100 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f2de:f1ff:feb2:5353/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:980003 errors:0 dropped:0 overruns:0 frame:0 TX packets:498384 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1320506168 (1.3 GB) TX bytes:59780591 (59.7 MB) Interrupt:20 Memory:f3a00000-f3a20000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:21927 errors:0 dropped:0 overruns:0 frame:0 TX packets:21927 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1781719 (1.7 MB) TX bytes:1781719 (1.7 MB) wlan0 Link encap:Ethernet HWaddr 24:77:03:29:8f:dc inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::2677:3ff:fe29:8fdc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11828 errors:0 dropped:0 overruns:0 frame:0 TX packets:15444 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4855662 (4.8 MB) TX bytes:2250585 (2.2 MB) [lucas@lucas-ThinkPad-W520]/home/lucas$ lspci -nn | grep 0280 03:00.0 Network controller [0280]: Intel Corporation Centrino Ultimate-N 6300 [8086:4238] (rev 3e) [lucas@lucas-ThinkPad-W520]/home/lucas$ rfkill list 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no with ethernet unplugged: [lucas@lucas-ThinkPad-W520]/home/lucas$ route -n | grep UG 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 wlan0 with ethernet plugged in: [lucas@lucas-ThinkPad-W520]/home/lucas$ route -n | grep UG 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 [lucas@lucas-ThinkPad-W520]/home/lucas$ nm-tool NetworkManager Tool State: connected (global) - Device: wlan0 [tg] ---------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: connected Default: no HW Address: 24:77:03:29:8F:DC Capabilities: Speed: 52 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) tatum: Infra, 40:8B:07:D8:A5:04, Freq 2437 MHz, Rate 54 Mb/s, Strength 42 W PA WPA2 ums: Infra, 00:20:A6:72:52:BF, Freq 2437 MHz, Rate 54 Mb/s, Strength 59 Alpha 40: Infra, 28:CF:E9:86:59:5D, Freq 5260 MHz, Rate 54 Mb/s, Strength 30 W PA WPA2 thepromiselan: Infra, 58:6D:8F:51:E5:54, Freq 2452 MHz, Rate 54 Mb/s, Strength 34 $ PA WPA2 xfinitywifi: Infra, 06:1D:D5:84:27:A0, Freq 2437 MHz, Rate 54 Mb/s, Strength 52 *tg: Infra, 00:02:6F:83:F8:F4, Freq 2462 MHz, Rate 54 Mb/s, Strength 73 W PA2 ums: Infra, 00:20:A6:A1:9F:25, Freq 2452 MHz, Rate 54 Mb/s, Strength 44 BRIAN-PC_Network:Infra, 20:AA:4B:DD:93:D6, Freq 2462 MHz, Rate 54 Mb/s, Strength 35 W PA2 HOME-C0F8: Infra, 44:32:C8:D2:C0:F8, Freq 2412 MHz, Rate 54 Mb/s, Strength 40 W PA WPA2 abcsexy: Infra, 28:28:5D:27:5D:85, Freq 2412 MHz, Rate 54 Mb/s, Strength 27 W PA WPA2 IPv4 Settings: Address: 192.168.0.105 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1 - Device: eth0 [Wired connection 1] ------------------------------------------- Type: Wired Driver: e1000e State: connected Default: yes HW Address: F0:DE:F1:B2:53:53 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.0.100 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1

    Read the article

  • Wireless Connection Troubles

    - by James
    I just recently switched from Windows 7 over to Ubuntu 12.04 and have been experiencing some issues connecting to my home's wireless network. The only way I can get it to connect to the network is by disabling IPv4 and IPv6 settings. Even then while it says its connected to the network (3 bars), I'm unable to access the Internet. It connected for a little while after I first installed Ubuntu, but after the first reboot I haven't been able to access the web at all. I have very basic knowledge when it comes to computers and barely any when dealing with Ubuntu and Linux. I'm very happy with Ubuntu apart from this one issue, as before my computer was overheating and crashing, I've yet to experience any of those problems since installing Ubuntu. The information I can give may be very limited since I'm having to use my cell phone to figure out the solution to this. Any help would be greatly appreciated. Thanks in advance!

    Read the article

  • Ubuntu 12.04 Hp G72 Problem Installing proprietary wireless driver

    - by user69402
    I have a fresh Ubuntu 12.04 installed on HP G72 machine. In order for my wireless to work I need the proprietary driver installed - Broadcom STA wireless driver. Trying to install it from the System Settings gives me the error: "Sorry, installation of this driver failed. Please have a look at the log file for details: /var/log/jockey.log". So far I suspect the error to be caused by the bad "bcmwl-kernel-source" installation. What i tried: 1. remove "bcmwl-kernel-source" 2. install "bcmwl-kernel-source" installation through the terminal ends with "error code (1)". I would greatly appreciate any help Here is everything that the terminal returns: Reading package lists... Done Building dependency tree Reading state information... Done The following NEW packages will be installed: bcmwl-kernel-source 0 upgraded, 1 newly installed, 0 to remove and 0 not upgraded. Need to get 0 B/1,151 kB of archives. After this operation, 3,514 kB of additional disk space will be used. Selecting previously unselected package bcmwl-kernel-source. (Reading database ... 170331 files and directories currently installed.) Unpacking bcmwl-kernel-source (from .../bcmwl-kernel-source_5.100.82.38+bdcom-0ubuntu6.1_amd64.deb) ... Setting up bcmwl-kernel-source (5.100.82.38+bdcom-0ubuntu6.1) ... Loading new bcmwl-5.100.82.38+bdcom DKMS files... /usr/sbin/dkms: line 467: unset: POST_REMOVE$PRE_BUMLD': not a valid identifier /usr/sbin/dkms: line 467: unset:BUILD_E\CLUWIVE_ARCH': not a valid identifier /usr/sbin/dkms: line 467: unset: $': not a valid identifier /usr/sbin/dkms: line 467: unset:$': not a valid identifier /usr/sbin/dkms: line 467: unset: modules_conf_arra}': not a valid identifier /usr/sbin/dkms: line 467: unset:$': not a valid identifier /usr/sbin/dkms: line 467: unset: $': not a valid identifier /usr/sbin/dkms: line 467: unset:$': not a valid identifier /usr/sbin/dkms: line 467: unset: $': not a valid identifier /usr/sbin/dkms: line 467: unset:$': not a valid identifier /usr/sbin/dkms: line 467: unset: `$': not a valid identifier /usr/sbin/dkms: line 419: ${!POST_REMOVE$PRE_BUMLD[@]}: bad substitution /usr/sbin/dkms: line 419: ${!BUILD_E\CLUWIVE_ARCH[@]}: bad substitution /usr/sbin/dkms: line 419: ${!$[@]}: bad substitution /usr/sbin/dkms: line 419: ${!$[@]}: bad substitution /usr/sbin/dkms: line 419: ${!$[@]}: bad substitution /usr/sbin/dkms: line 419: ${!$[@]}: bad substitution /usr/sbin/dkms: line 419: ${!$[@]}: bad substitution /usr/sbin/dkms: line 419: ${!$[@]}: bad substitution /usr/sbin/dkms: line 419: ${!$[@]}: bad substitution /usr/sbin/dkms: line 419: ${!$[@]}: bad substitution malloc: ../bash/subst.c:3671: assertion botched free: start and end chunk sizes differ Aborting.../tmp/tmp.pEXTnftUfI: line 4: modules_conf_arra}[[@]}]=[[@]}]}: command not found dkms.conf: Error! No 'DEST_MODULE_LOCATION' directive specified for record #0. dkms.conf: Error! Directive 'DEST_MODULE_LOCATION' does not begin with '/kernel', '/updates', or '/extra' in record #0. dkms.conf: Error! No 'PACKAGE_VERSION' directive specified. Error! Bad conf file. File: /usr/src/bcmwl-5.100.82.38+bdcom/dkms.conf does not represent a valid dkms.conf file. dpkg: error processing bcmwl-kernel-source (--configure): subprocess installed post-installation script returned error exit status 8 Errors were encountered while processing: bcmwl-kernel-source E: Sub-process /usr/bin/dpkg returned an error code (1)

    Read the article

  • Ubuntu 11.10 to 12.04 results in loss of N network capability - how to restore?

    - by user74273
    On Ubuntu 11.10, I had zero issues with N network detection and speed. I cannot remember whether the old driver was iwlagn or iwlwifi. This was with Ubuntu repository Linux kernel 3.0.0-22. Upon upgrading to Ubuntu 12.04, iwlwifi is the available driver and while it detects N networks, upon connection, the speed is cripplingly low and DNS look-ups do not occur (impossible to browse). This is with Ubuntu repository Linux kernel 3.2.0-26. Please note that the 11n_disable flag for the iwlwifi module cannot work for me as I require N network access. Is there another solution? Perhaps, is there a way to easily patch the new kernel with the old wireless module (just copy-and-paste the iwlagn module into the new kernel source and re-compile)? Relevant hardware specs: Dell Inspiron N5110 Network Adapter: Intel® Centrino® Wireless-N 1030

    Read the article

  • How to setup a wifi ap hotspot with ipv6 support?

    - by keyman
    How to setup a wifi ap (access point mode) hotspot, with IPv6 support? I've set up a hotspot according to the guide to wifi ap hotspot setup and it works fine. But via the hotspot I failed to visit IPv6 websites. How can I setup a hotspot able to share Ipv6 Internet access? Thanks! Further: Actually I've tried to setup IPv6 forwarding and masquerading. First enabling IPv6 forwarding: echo 1 | sudo tee net/ipv6/conf/default/forwarding Then I tried to execute: sudo ip6tables -t nat -A POSTROUTING -s 2001:db8:0:1::/64 -o eth0 -j MASQUERADE But it gave me an error: ip6tables v1.4.12: Couldn't load target `MASQUERADE':No such file or directory I searched through the Internet but I get confused. So I'm here for help. Thanks!

    Read the article

  • Windows 2008 Routing and Remote access server - access to the internet

    - by Ian
    I have a windows 2008 r2 remote access server set up and running. The remote access works fine. My problem is that the remote access server itself doesn't have access to the internet. The box has two interfaces, an internal and an external. Inbound connections come in on the external interface and RRAS responds. All wall and nice. I want to be able to use windows update, browse, etc from this box but can't as the outbound traffic just gets blocked. I've tried going into the RRAS mmc tool and opening the interface properties, under which there are two buttons for inbound and outbound filters. There I tried adding ports 80 and 443, but this doesn't work completely. I can see the connection initiating (Syn goes out) but the session never establishes itself. Anyone done this or got any suggestions?

    Read the article

  • Proper Drivers for 10.10 Realtek RTL8176 Wireless and Synaptic V7.2 Touchpad Devices

    - by av7000
    I have a new Toshiba Satellite L645-S4059. This is an Intel i3 64 bit machine. Two problems have occurred that I would like to fix before transferring my work from my old compaq laptop. First I can't get the wireless driver to work properly. I went to the realtek driver site and couldn't find the 8176. Instead I was shuttled to the 8188 which uses a 8192 software release. I am not sure if the kernel is just missing the name. Second I have a synaptics V7.2 touchpad which is just flaky. It eventually freezes up so I am just using a USB mouse. Appreciate anybody's experience on this.

    Read the article

  • Wireless card disappeards when restart ubuntu

    - by Kristian Jones
    I used 'additional drivers' to install 'Broadcom STA wireless driver' and it returns an error. WIthin jockey.log it says the following numerous times. 2011-02-14 21:24:06,945 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: blacklisted, b43legacy: blacklisted After it returns the error the network card will work temporarily until I restart the laptop. When I restart I got to go through the procedure again of trying to activate the driver, returns an error however it works temporarily. The network card is as follows on a Dell Inspiron 1545: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] Rev 01 I have been trying to solve this myself for many hours. Any help is appreciated/

    Read the article

  • Wireless device not working...supposed problem with b43 driver

    - by Francesco
    I just installed Xubuntu 11.10 onto an old Acer Aspire 3003wlmi. The wireless card is not working. I did all the passages illustrated in the troubleshooting guide but I came up with nothing. It says that driver is b43, but when I booted from the installation cd I noted down some messages saying "Error - b43/ucode " and "Error b43/phy_...something". I had Ubuntu 10.10 installed before and I remember I had similar problems but I don't remember how to solve it. If you please can help me. thanks a lot. Francesco

    Read the article

  • Broadcom wireless card disappeards on restart

    - by Kristian Jones
    I used 'additional drivers' to install 'Broadcom STA wireless driver' and it returns an error. WIthin jockey.log it says the following numerous times. 2011-02-14 21:24:06,945 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: blacklisted, b43legacy: blacklisted After it returns the error the network card will work temporarily until I restart the laptop. When I restart I got to go through the procedure again of trying to activate the driver, returns an error however it works temporarily. The network card is as follows on a Dell Inspiron 1545: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] Rev 01 I have been trying to solve this myself for many hours. Any help is appreciated/

    Read the article

  • Ubuntu 12.10 64bit fresh install, wireless issue!

    - by Dave
    Just installed a fresh Ubuntu 12.10 64bit on my laptop, run the update manager, restarted and suddenly I can't use my wifi anymore. Ubuntu software center installed automatically the wifi additional driver as you can see in my screenshot. If I mark the option "Do not use the device" and apply changes, restarting Ubuntu my wifi is back and I can use it. If I run iwconfig my terminal is showing this Now if I use Ubuntu for more than 20 minutes surfing the web my wifi it keeps to be connected but I don't receive any signal from it. Any page I try to open it simply don't open (just waiting icon). If I disconnect my wifi and connect it again, same issue, it doesn't work. The only way to make it work again is to restart Ubuntu. And the same story it happens again after aprox. 20, 30 minutes. WIFI device details: 03:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) Thanks, Dave

    Read the article

  • Wireless speed drops over time and doesn't get up if not reconnected

    - by Vili Lehto
    I am using Ubuntu 12.10 64bit and I have a Asus PCE-N15 wireless card(in PCI-E slot). The problem is that first when I connect to my WiFi network the speed is just fine, and actually my link speed never drops, it shows a solid 150mb/s+ link speed and good signal. But the download and upload speeds drop dramatically after couple minutes of use and I have to reconnect to fix this. Network is type IEEE 802.11bgn and uses WPA2/AES encryption. I don't have similar problems on the windows side, and the network is working fine on every other device. iwconfig shows this: wlan0 IEEE 802.11bgn ESSID:"WLAN-AP" Mode:Managed Frequency:2.412 GHz Access Point: 00:1E:AB:05:EF:31 Bit Rate=300 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr=2347 B Fragment thr:off Encryption key:off Power Management:off Link Quality=61/70 Signal level=-49 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:2 Missed beacon:0 So the question is: Is there a way to fix this? Thanks in advance.

    Read the article

  • Installing wireless drivers without internet access [closed]

    - by Lucas Jones
    Possible Duplicate: How can I install and download drivers without internet? (This is related to my other question; my approach there didn't work.) My friend has (I'm quite sure) a Broadcom wireless chipset. However, he doesn't have any wired internet access on the machine, so his only option is to boot into Windows (he is using Wubi) and download packages there. This means we can't use the Hardware Drivers dialog to install the drivers. He can't fetch the repository information, so the Broadcom driver packages aren't showing up in Synaptic. Is there any way to get Wi-Fi working?

    Read the article

  • how to find available wireless networks

    - by Quinn
    I'm using an HP Pavilion dv6000 I've looked at other answers similar to this question how ever when I look at my network symbol it doesn't say anything that the answer below says "Make sure that your wifi hardware switch is on or not. It is either F2 or F12 or near to it. Once the switch is enabled, there is a small fan-like applet on the top panel (Gnome Network Manager), fourth from the right. Click on it and if there is no tick mark on the option 'Enable Wireless', enable it. Wait till your wifi connection name appears." it how says 'Enable Networking' my wi-fi switch is on and I've tried using terminal to kill the applet as another answer suggests trying. Does anyone have any other ideas that might help? Just in case anybodies curious as to how I'm posting this I'm on my other ubuntu laptop that's running an older version.

    Read the article

  • wireless not connecting in 12.04 update

    - by Julie
    I just updated from 10.04 to 12.04. I am not very knowledgeable at all with Ubuntu since it is still relatively new to me. I went through the whole update today and yesterday and now that it is finished it will not acknowledge that there are any wireless connections around, nor does it give me an option to pick one. it just tells me what ones I've used in the past. is there any way that someone can help me? I have read through and attempted almost every fix that everyone has found and nothing is working and I'm super confused.

    Read the article

  • Wireless suddenly dropping with a Ralink RT2870

    - by cwwk
    I have a Linksys WUSB600N v1 Dual-Band Wireless-N Network Adapter Ralink RT2870 USB dongle that worked flawlessly in 11.10. Since upgrading, I can't keep a connection for more than five minutes. The wild world of Google was unable to provide a solution, and I would rather not downgrade although that remains a possibility. Results of syslog: slack@slack:~$ tail /var/log/syslog Apr 26 20:26:10 slack AptDaemon: INFO: Initializing daemon Apr 26 20:26:10 slack AptDaemon.PackageKit: INFO: Initializing PackageKit compat layer Apr 26 20:26:10 slack dbus[972]: [system] Successfully activated service 'org.freedesktop.PackageKit' Apr 26 20:26:10 slack AptDaemon.PackageKit: INFO: Initializing PackageKit transaction Apr 26 20:26:10 slack AptDaemon.Worker: INFO: Simulating trans: /org/debian/apt/transaction/aaed4e38eb3c41ad86d2bab6ca03ee7c Apr 26 20:26:10 slack AptDaemon.Worker: INFO: Processing transaction /org/debian/apt/transaction/aaed4e38eb3c41ad86d2bab6ca03ee7c Apr 26 20:26:12 slack dbus[972]: [system] Activating service name='com.ubuntu.SystemService' (using servicehelper) Apr 26 20:26:12 slack dbus[972]: [system] Successfully activated service 'com.ubuntu.SystemService' Apr 26 20:30:26 slack AptDaemon.PackageKit: INFO: Get updates() Apr 26 20:30:27 slack AptDaemon.Worker: INFO: Finished transaction /org/debian/apt/transaction/aaed4e38eb3c41ad86d2bab6ca03ee7c Any suggestions?

    Read the article

  • Wireless connects but can not connect to internet

    - by Dan
    I'm using Ubuntu 11.04 and I'm having trouble connecting to internet via wifi. Ethernet cable works though. So when I log on it auto logs on to my wifi connection at home but after about a minute or so it gives me a popup: network disabled something about .local domain and something about Avahi network (sorry if you need more on what the popup says I will reboot and look at it again). I am using Atheros wireless card. My laptop is Asus G73SW and on the forum at notebookreview.com G73SW Owner's Lounge people said they had no problem with connecting via wifi from install. Please help me because I would love to keep using this beautiful OS.

    Read the article

  • brother MFC-J435W wireless scanning issue

    - by ogreen32
    Thanks for taking the time to read this. I have a brother MFC-J435W and I was able to get the printer set up for wireless printing, but it is not allowing me to scan wirelessly. It gives me the message to "check connection". I'll tell you what I've done so far and maybe someone can help me out. I've installed the scanner driver and scan tool I installed Xsane (to see if it would allow the scanner to communicate with the computer and that didn't help). I've tried restarting the computer. After those things I am now at a loss as to where to go from here. Any help would be great. Thanks. I've also searched for this question in the Brother FAQ as well as on here and I haven't found an answer. Thanks again.

    Read the article

< Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >