Search Results

Search found 4690 results on 188 pages for 'ran gualberto'.

Page 132/188 | < Previous Page | 128 129 130 131 132 133 134 135 136 137 138 139  | Next Page >

  • How do I uninstall a ruby version installed via source?

    - by Aaron McIver
    I installed a version (1.9.3-p194) of ruby via source using make install and realized this may have been the wrong route to take. Upon doing this, I realized this was a mistake and I should be using a solution such as rvm to address my ruby versions within the OS. I looked to see if an uninstall existed to be ran in conjunction with make and it didn't. I then proceeded to install rvm and add the aforementioned version in to my list of managed rubies within rvm which is not listed as ext-ruby-1.9.3-p194. rvm rubies ext-ruby-1.9.3-p194 [ x86_64 ] =* ruby-1.9.3-p194 [ x86_64 ] # => - current # =* - current && default # * - default** When I perform an rvm remove, it simply removes it from the rubies list however it still exists within /usr/local/bin. I am not concerned with the system install ruby version residing in /usr/bin as I understand that is tied to the OS and should simply be ignored. How can I safely uninstall/remove the aforementioned version and all the places in which it was installed, short of looking at the install script?

    Read the article

  • Can't access server sound card when vnc'd into ubuntu server

    - by Corey Kennedy
    I've set up my ubunutu 10 server with xfce, nxserver, and now tightvncserver so that I can control it remotely from my Windows 7 laptop. NX is working fine for remote access, but when I run (for example) exaile, no sound will be sent through the server's sound card. I installed tightvncserver and connected, but ran into the same problem. Exaile opens, sound isn't muted, I can see that sound cards are installed (via cat /proc/asound/cards), but I can't seem to get the remote sessions to access the server's sound card. Also, just to confirm that the sound card was working I hooked up a montior/keyboard to the server and opened a local xfce session. That worked fine. While I had the local session running, I was also able to open a remote session with NXClient and start exaile - which then successfully piped sound to the local card. After disconnecting the monitor/keyboard and moving the box back to its normal spot, though, I was not able to play sound via either an NX or VNC session. Does anyone have any suggestions? Surely it's possible to configure my remote sessions to pipe sound to the server's sound card, right? Or at least get xfce up and running without a monitor or keyboard but with access to the sound card so I can VNC into it? Thanks!

    Read the article

  • How do I cancel windows server 2003 repair install?

    - by Kilgore2k
    System: Windows 2003 Server Enterprise Scenario: NTDS db is corrupt and all attempts to fix with esentutl fail. Ran chkdsk which seemed to repair disk error and give access to the ntds.dit file but still esentutl fails. (Attached the drive to a different server to run the esentutl) Error: Access to source database '[path to copy of]/ntds.dit' failed with Jet error -1022. Operation terminated with error -1022 (JET_errDiskIO, Disk IO error) after 0.170 seconds. This error occurs on any disk I cpoy the files to including original location in C:\WINDOWS\NTDS\ Now enter the "Stupid!" and "what was I thinking!?" part (must be the late hour...) Stupid: No updated backup - after using a backup I get a network password error in the lsass error. what was I thinking!?: Started the install repair from the original CD but the install fails since the AD fails to start. Now I cant boot into any mode (safe mode, AD restore etc) nor complete the repair install. I would really like to avoid a fresh install since I have the Exchange server on this DC and would rather migrate to a new server than have to start from scratch. Thanks!

    Read the article

  • Western Digital HDD disappears and reappears in BIOS

    - by tbkn23
    I know many people asked about similar problems, but I have a very specific case where I can't understand what's going on... I have a 3TB Western Digital Caviar Green disk connected in my Desktop, that also has a seagate 1.5TB disk and 2 SSD drives (OCZ and Sandisk). After working fine for quite some time (probably more than a year), suddenly my Caviar Green drive disappeared from windows. I checked the BIOS, and it wasn't there either. I opened my PC, played with the connectors, power, etc, but nothing helped. Even tried switching connectors with those of the 1.5TB disk, and nothing changed, the 1.5TB seagate was there, but the 3TB WD was not. Ok, now for the strange part. I have another desktop at home, so I took out my 3TB drive, connected it there, and it worked fine! I copied the most important files out of it, and then made another attempt in the original desktop. Surprise! It now appeared in the BIOS and worked fine! I even ran the SMART test with the WD tools and it said everything was intact. It doesn't end here. After leaving it overnight in the original desktop, it disappeared again in the morning. I repeated the entire process, connecting it to the second desktop, and there it is again working fine. Now for my question... Whats going on? The disk seems to be appearing on/off in my original Desktop, while other drives there work fine. SMART test says the disk is fine. Any ideas? Is the disk defective and should be replaced? Or maybe there's a problem with the controller in the desktop? I'm using a Gigabyte GA-880GA-UD3H motherboard and tried connecting the drive to both bridges (SATA2 and SATA3 bridges). Thanks EDIT: Power options are set never to turn off hard drives:

    Read the article

  • GPO - Setting not applied, although policy is applied

    - by Kenny Bones
    This is rather strange. In our domain we have several terminal servers and this morning a user reported that no drives are mapped when he logs on to the terminal server. So, I checked Group Policy Results and compare two users. Both users have the exact same policies applied. But for this particular user, the Script section under User Configuration - Policies - Windows Settings is just not there. For the other user, which this is working fine for, it says under the Script section that Winning GPO is Terminal2008, which is the GPO that contains the script section. And the Terminal2008 GPO is applied to both users. Also, the loopback processing is set to Replace. What could be the cause for this? I've never seen this particular issue before. I mean, both users are in the same OU, they log on to the same terminal server and the same policies are applied to both. They do not however have the exact same group memberships, but should that matter? It's not stated that the script should be run only if the user is a member of a certain group either. Not sure if that could be done through that specific setting either.All I know is, the very same policies are applied to both users, in the same OU and the same computer. Meaning, the same policies should be applied? Edit: I just ran Group Policy Results on one of the other terminal servers, which are also in the same OU, and the Scripts section is there! This means that this particular user don't get this setting when he's logged onto this particular server. What could be the cause of this?

    Read the article

  • PC dies when running at 100% CPU

    - by user155631
    I recently wrote some Java code to generate images of the Mandelbrot set (fractal). I made use of the new Fork/Join facility in Java 7 to run separate threads on all four cores (2 real, 2 virtual)simultaneously, using a large number of iterations for greater accuracy. The problem is, the process runs fine for about a minute, and then it's as if someone has pulled the plug and the PC just dies. I thought it must be the CPUs overheating, so I ran Real Temp to monitor the temperature. It's an Intel i3 processor. I can see the temperature creeping up to 70 degrees, and then it seems to level off there and run for about another 30 seconds before dying. According to Real Temp, there's still a gap of 35 degrees between the actual temperature and TJ max. I also tried disabling "CPU TM function" in the BIOS, but the problem still occurs. A colleague suggested that it might be a power supply problem, so I borrowed a more powerful PSU (can't remember what wattage it was, but it's higher than mine which is 500W). The exact same thing still happens though. Is anyone able to suggest what the problem might be, or what I can try next?

    Read the article

  • Having two IP Routes/Gateways of last Resort on an HP Switch

    - by SteadH
    We have an HP Layer 3 Switch that is doing IP routing between vlans. The general set up is that the switch has an IP address on each VLAN and IP routing is enabled. On our servers VLAN, we have a firewall that has a connection to the outside world. To set a IP route on the HP router, we use IOS command ip route 0.0.0.0 0.0.0.0 192.168.2.1 where 192.168.2.1 is the address of our firewall, and the zeros essentially mean to route all traffic that the switch doesn't know what to do with out the firewall as a gateway. We're in the middle of an ISP and firewall change. I set up the new firewall and ran the IOS command ip route 0.0.0.0 0.0.0.0 192.168.2.254 (the address of the new firewall). Things started working nicely. When I reviewed the configuration of the switch though, I noticed that it did not replace the previous ip route command, but just added another route. Now, I know how to remove the old firewall route (no ip route 0.0.0.0 0.0.0.0 192.168.2.1), but what is the effect of having these two 0.0.0.0 routes? Is it switch implosion? Will a server just respond back over the route it receives the request from? I've read elsewhere that having two default gateways is an impossibility by definition, but I'm curious about this situation that our switch allowed. Thanks!

    Read the article

  • How can I make grub2 boot into Windows 7?

    - by Grzenio
    I had Windows 7 installed on my system, then I installed Debian testing with grub2 as its boot manager. Initially I couldn't see windows entry in grub at all, so I ran: aptitude install os-prober kcpuload update-grub Now I can see the entry, but when I select it I get only Win7 system restore, instead of the the real thing. Any ides how to make it work? EDIT: I tried the suggested approach to add a new file to /etc/grub.d, which generated an entry in grub.cfg, but it does not appear in the grub menu on boot :( I have this: grzes:/home/ga# cat /etc/grub.d/11_Windows #! /bin/sh -e echo Adding Windows >&2 cat << EOF menuentry “Windows 7? { set root=(hd0,2) chainloader +1 } And I have the following grub.cfg file: grzes:/home/ga# cat /boot/grub/grub.cfg # # DO NOT EDIT THIS FILE # # It is automatically generated by /usr/sbin/grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then load_env fi set default="0" if [ ${prev_saved_entry} ]; then set saved_entry=${prev_saved_entry} save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z ${boot_once} ]; then saved_entry=${chosen} save_env saved_entry fi } insmod ext2 set root=(hd0,3) search --no-floppy --fs-uuid --set 6ce3ff31-0ef7-41df-a6f5-b6b886db3a94 if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=640x480 insmod gfxterm insmod vbe if terminal_output gfxterm ; then true ; else # For backward compatibility with versions of terminal.mod that don't # understand terminal_output terminal gfxterm fi fi set locale_dir=/boot/grub/locale set lang=en insmod gettext set timeout=5 ### END /etc/grub.d/00_header ###

    Read the article

  • computer freezes but music continues

    - by Danny
    Recently I have had a problem where my computer will freeze completely but if I happen to be streaming Pandora in a tab that will continue playing. If I wait about 2-5 minutes it will eventually come back and start working normally. I also noticed that during the period that it is unresponsive that the HDD activity light stays lit the whole time, not flashing. I've ran memtest86+ and a diagnostic from Western Digital for my HDD model and none of them reported any errors. The specs for my computer are 1 x ASRock H55M/USB3 R2.0 LGA 1156 Intel H55 HDMI USB 3.0 Micro ATX Intel Motherboard 1 x CORSAIR Enthusiast Series CMPSU-550VX 550W ATX12V V2.2 SLI Ready CrossFire Ready 80 PLUS Certified Active PFC Compatible with Core i7 Power Supply 1 x Intel Core i3-540 Clarkdale 3.06GHz LGA 1156 73W Dual-Core Desktop Processor Intel HD Graphics BX80616I3540 1 x G.SKILL 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Dual Channel Kit Desktop Memory Model F3-12800CL9D-4GBNQ 1 x ASUS PCE-N13 PCI Express 150/300Mbps Transfer/Receive Rate Wireless Adapter 1 x EVGA 01G-P3-1556-KR GeForce GTX 550 Ti (Fermi) FPB 1GB 192-bit GDDR5 PCI Express 2.0 x16 HDCP Ready SLI Support Video Card I can't imagine what would be causing these problems.

    Read the article

  • Cisco Call Manager adding 7945's

    - by Will
    Hello we currently have a call manager settup (older we are working on upgrading it) but for now we are looking to add 7945 IP phones. We currently have 7960's all over the place, but we can't get these new anymore. Here is the info about our call manager ace.dll 5.2.5.0 CCM4.1(3) aced.dll CCM4.1(3) AdministrativeReportingTool.exe 4.1(0.45) 4.1(3)sr4d Apache Tomcat 4.1 CCM4.1(3) ASTIsapi.dll 3.3.2.0 4.1(3)sr4d AudioTranslator.exe 4.0.0.3 CCM4.1(3) Aupair.exe 4.1.3.10472 4.1(3)sr4d AupairChangeNotify.dll 4.1.0.11 CCM4.1(3) AuthFilt.dll 4.0.0.0 4.1(3)sr4d AVVIDCustomerDirectoryConfigurationPlugin.exe 4.1.0.17(0) CCM4.1(3) bootp.exe 2.0.2.2 CCM4.1(3) BulkAdministrationTool.exe 5.1(4c) 4.1(3)sr4d CallBackService.exe 3.3.2.3 4.1(3)sr4d ccm.exe 4.1.3.17472 4.1(3)sr4d CcmPerfMon.dll 4.1(3)sr4d CCNTEST.EXE CCM4.1(3) cdpintf.dll 4.0.0.0 CCM4.1(3) Cisco CallManager 4.1(3)sr4d 4.1(3)sr4d One of the admins recommenced downloading a device pack, which we did. However when we ran it on the call manager server it gave the error "unable to read script" Any recommendations on how to get these phones working with our Call Manager? Thank you.

    Read the article

  • Moving a lot of small files between servers using rsync

    - by Adirael
    Hello guys, I'm moving a lot of files (about 2 millions) between two servers on different locations using rsync over ssh, it seems to work fine but I just realised I'm losing some files on the process. I got server 1, with the original data, and server 2, with the copy. Server 1 runs CentOS 5 and Server 2 runs on Ubuntu 10. I'm doing the transfer on the Server's 2 command line like this: rsync -e ssh -avzn usr@server1:/remote/path /local/path The first file movement I did using tar, but I didn't though of piping it through ssh and it failed cause the disk on server 1 was almost full, so I transfered it anyways (it was about 200GB) and got about 80% of the files. Then I piped another tar with the rest of the files (they're in folders, I got 100 folders with about 30 subfolders each, with files inside) and now I got everything on server 2. I wanted to be sure, so I my two options are getting the md5sum of all the files and check them or running an rsync on server 2 against server 1, that's what I did. It got some missing stuff and now it says there's nothing more to do (DRY RUN). But I got at least two files that are missing inside a subfolder. I ran that same rsync on that folder, but still dry run. Am I doing something wrong? Thanks, and sorry for the wall of text.

    Read the article

  • Windows 7 hangs on black screen for a while after log in

    - by steini
    I get the welcome screen. I click on my user and get the "logging on" screen. After that all I get is a black screen with a mouse cursor. I can't even start task manager. No ctrl+alt+del or ctrl+shift+escape. It stays like this for about 10 minutes, then the desktop finally starts loading. According to the hdd led on my case, windows isn't even trying to access the hard drive for that whole time. It's just hanging doing nothing it seems. What I have tried: Uninstalled video driver and removed leftovers with driver sweeper Disabled all startup programs and non microsoft services Loaded "last known good configuration" Ran the alleged "black screen fix" from prevx against my best judgement (don't really like running random exes without knowing what they do at all) None of that works. I can boot into safe mode normally. My specs: i7 920 Gigabyte X58-UD3R Gigabyte HD5870 1GB 12GB Mushkin Silverline 1333MHz Windows 7 Ultimate x64 I'm also having another problem which I suspect is related. After I have gotten the computer up and running, everything works perfectly, but when it's been on for a while it starts behaving strangely when changing display modes. When I start up a game or anything that changes the screen resolution the computer freezes for about a minute every time until I reboot again. I think this is probably related to the black screen problem. Just thought I'd check to see if anyone has had the same problem. Let me know if I should post any more details about my system to help diagnose this. Thanks in advance.

    Read the article

  • Adding Multiple Interfaces to EC2 Ubuntu 12.04

    - by nocode
    I have a m1.medium Ubuntu 12.04 instance with two ENI's. I have a VPC setup with a private and public subnet. Private: 10.50.1.0/24 Public: 10.50.101.0/24 I initiated the instance on the private subnet. I configured a NAT instance and route all servers in the private subnet internet access. The route tables on the private subnet point towards the NAT instance and the route table on the public subnet point to the internet gateway. I am trying to add a public interface on the machine so that I can put it behind a ELB. When I added the second ENI and configured a static IP in /etc/network/interfaces and restarted the network services, I can no longer access from the Public subnet to the Private Subnet. Works Private private Private public Does not work Public private From Public Private, I ran a TCPDUMp on the private machine and can see the request coming in. My guess is it's trying to route over the new Public interface instead of the Private. Here's my route: default 10.50.1.1 0.0.0.0 UG 100 0 0 eth0 10.50.1.0 * 255.255.255.0 U 0 0 0 eth0 10.50.101.0 * 255.255.255.0 U 0 0 0 eth1 My networking knowledge is limited and I believe I have to add some routes but unsure of what command/syntax needs to be.

    Read the article

  • Can't delete ntuser.dat file to remove profiles after reboot

    - by Matrix Mole
    I've ran into an issue where some servers will not release the handle on the ntuser.dat file even after a reboot. Or quite possible, after the reboot, the ntuser.dat file is getting re-loaded into memory. The user accounts are definitely not being accessed (some of them belong to users that have not been with the company in over a year). It seems to be on Windows 2003 servers, but I can't be 100% certain that there aren't some 2000 servers showing this issue as well. When I try to use process explorer or handle.exe from sysinternals to kill the handle on these ntuser.dat files, the handle remains open and connected. Handle.exe even reports that the handle was broken while it remains in use. I've even taken ownership on the file and tried to kill the handle to no effect (windows shows I have ownership of the file, but still refuses to release the handle). I have looked into the registry to see if I can discover where the files may be getting loaded at. Unfortunately, the username is appearing in too many places for me to be certain which one is actually loading their reg file into memory. Any suggestions on how I can either break the handle on the files, or prevent them from getting re-loaded after a reboot?

    Read the article

  • Can't find partition tab in disk utility osX ver. 10.6.8

    - by John W
    I just got a used Mac Book Pro. I created a new admin account and deleted the old one as well as one other user. This is an older late 2007 MBP... the osX upgrade to 10.6.8 was just performed. My Macintosh HD is showing up as Partition 2. I ran disk utility (not from install disk), but there was no partition tab. I have a 160GB drive with only 53GB of space left on it. Since I am the only user and have no files on the laptop yet, I don't understand why there is so little space left. Surely the OS can't use up over 100GB. I wanted to run disk utility to see if there were any recovery partitions or other partition left over from the previous owner that could be erased to make room for expanding the main partition. Unfortunately, there is no partition tab in disk utility. The documentation I have found on line states that this version of osX includes that utility. The osX disks I have are for an older version so I wasn't sure if they would be of any use in solving this problem. Also, I was afraid if using the disks, would I lose the little bit of data/apps that I have assembled. I would rather not do a fresh install and have to do all the updates again to achieve this. The previous owner had some apps that I don't want to lose as I would have to pay handsomely to get them back. Simply, if all the previous users data is backed up on here after deleting user is still taking up space on a recovery partition (that I can't see)... I need to locate it erase it and expand the primary partition to re-aquire disk space for my files. I am new to Mac, so please be as descriptive as possible. Thanks.

    Read the article

  • Upgrading PHP, MySQL old-passwords issue

    - by Rushyo
    I've inherited a Windows 2k3 server running an XAMPP-installation from the stone age. I needed to upgrade PHP to facilitate an upgrade to MediaWiki to facilitate a new MediaWiki extension (to facilitate some documentation to facilitate doing my job to facilitate getting paid to facilit... you get the idea). However... installing a new version of PHP resulted in PHP's MySQL libraries refusing to communicate using MySQL's 'old style' 152-bit passwords. Not a problem in theory. The MySQL installation is post-4.1, so it should have the functionality to upgrade the user's passwords from 152-bit to 328-bit (what a weird hashing algorithm...). I ran the following: SET PASSWORD = PASSWORD('foo'); on MySQL but querying: SELECT user, password FROM mysql.user; returned just the same password I started out with - 152-bit. Now... I suspect you're thinking 'AHA! old-passwords is on!'. Unfortunately it's not - I've disabled it in the configuration (explicitly set it to 0), made doubly sure I have an absolute reference to that configuration file and ensured the service isn't using the --old-passwords flag. The service was reset after each and every operation. So I went onto another system and generated the 328-bit hash on there, copying the hash over to the first MySQL instance. Unfortunately, that didn't work either (I did remember to FLUSH PRIVILEGES). The application error is: "'mysqlnd cannot connect to MySQL 4.1+ using the old insecure authentication. Please use an administration tool [...snip...] Is there anything else I can try to get PHP to recognise MySQL as not using the 'old insecure authentication'? MySQL seems to be stuck in 'old-passwords' mode and I can't get it out of it.

    Read the article

  • "Dictionary problem." Error with VMPlayer

    - by George Mauer
    I'm pretty new to using vmware virtualization (been a virtualbox user) so I'm hoping you guys can help me out. I recently got an external usb disk containing a vm for a client, downloaded vmplayer, set it up with "Open a Virtual Machine", ran it, easy as pie. After working with it a bit this morning, I shut the VM down and now trying to start it back up again I get this: I tried removing the vm from my library, now it happens whenever I try to add it back in. In the meantime, I can still access other virtual machines so it seems like the problem might be with the virtual disk. So two questions: This is obviously not a very helpful error message. Where can I go to get more information? My Application EventLog doesn't contain anything from VMWare. What steps can I take to fix the problem? Edit: A couple more pieces of information. I did not take any snapshots. I don't think VM Player even has that ability. I have a zip file of (what I assume) is the state of the VM when it was sent to me. I cannot unzip it as it is huge and simply requires more HD space than I have available but I did extract the vmx file and examine it. Other than the UUIDs and the fact that mine reads cleanShutdown = "FALSE" they are identical. The log contains the following lines Jun 23 10:11:18.080: vmx| SNAPSHOT: SnapshotConfigInfoRead: Unable to load dict from 'E:....\MachineName.vmsd'. Jun 23 10:11:18.080: vmx| SNAPSHOT: SnapshotConfigInfoRead failed for file 'E:....\MachineName.vmx': Dictionary problem (6) Jun 23 10:11:18.082: vmx| SNAPSHOT: Snapshot_TimeStampTiers failed: Dictionary problem (6)

    Read the article

  • Who should I run mysql as, on a personal computer?

    - by user664833
    I just installed mysql via homebrew (with brew install mysql, on Mac OS X Mountain Lion - recently installed from scratch). Following the installation, there is a "caveats" section with options around further necessary actions to take: ==> Caveats Set up databases to run AS YOUR USER ACCOUNT with: unset TMPDIR mysql_install_db --verbose --user=`whoami` --basedir="$(brew --prefix mysql)" --datadir=/usr/local/var/mysql --tmpdir=/tmp To set up base tables in another folder, or use a different user to run mysqld, view the help for mysqld_install_db: mysql_install_db --help and view the MySQL documentation: * http://dev.mysql.com/doc/refman/5.5/en/mysql-install-db.html * http://dev.mysql.com/doc/refman/5.5/en/default-privileges.html To run as, for instance, user "mysql", you may need to `sudo`: sudo mysql_install_db ...options... Start mysqld manually with: mysql.server start Note: if this fails, you probably forgot to run the first two steps up above A "/etc/my.cnf" from another install may interfere with a Homebrew-built server starting up correctly. To connect: mysql -uroot To launch on startup: * if this is your first install: mkdir -p ~/Library/LaunchAgents cp /usr/local/Cellar/mysql/5.5.27/homebrew.mxcl.mysql.plist ~/Library/LaunchAgents/ launchctl load -w ~/Library/LaunchAgents/homebrew.mxcl.mysql.plist * if this is an upgrade and you already have the homebrew.mxcl.mysql.plist loaded: launchctl unload -w ~/Library/LaunchAgents/homebrew.mxcl.mysql.plist cp /usr/local/Cellar/mysql/5.5.27/homebrew.mxcl.mysql.plist ~/Library/LaunchAgents/ launchctl load -w ~/Library/LaunchAgents/homebrew.mxcl.mysql.plist You may also need to edit the plist to use the correct "UserName". On previous versions of Mac OS X I ran mysql as mysql user, but now I am confronted by the idea of running it as myself. I am the only one who uses this computer (which happens to be my laptop), and I do programming for work and for pleasure. What are the pros & cons, or best practices, around choosing whether to run mysql AS YOUR USER ACCOUNT or as mysql or something else still?

    Read the article

  • How to kill ostensibly immortal process?

    - by DeeDee
    I had some huge file transfers operating on an NFS mount. The server on which the mount point resided was carelessly rebooted, and now the server from which these large transfers were initiated seems to be bogged down by them. If I run top, I see the following: The first thing I tried was to run kill with each the -1 -2 -9 and -15 flags, and each of the process ids shown above in turn. This allowed me to proceed, but didn't kill the processes. The next thing I attempted was to reboot the server, but neither reboot nor shutdown -r now worked. When I ran shutdown -r now the standard broadcast message was sent out, but the sever did not reboot. I confirmed this by looking at the server uptime, which was 25 days. So now I'm a little stuck. I'm running these commands as root. EDIT: Here's another interesting tidbit: In top, I don't see that any other processes are using more than a fraction of a percent of memory or more than 5% of CPU. EDIT 2: output of /var/log/messages

    Read the article

  • Certain websites redirect to 127.0.0.1. How do I fix this?

    - by Dian
    Facebook and Youtube in particular. Tried nslookup the address shows as 127.0.0.1. Checked the HOSTS file, it's fine. Ran Malwarebytes' Anti-Malware (didn't find any problems) and SpyBot Search and Destroy (found 1 problem). (Not sure if the Spybot made this improvement) now pinging youtube shows the correct address (74.125.71.91) but the browser still says: Connection to 127.0.0.1 Failed The system returned: (111) Connection refused Tried ipconfig /flushdns but there are no changes. Switched to another user but the results are the same. hosts file: # Copyright (c) 1993-2009 Microsoft Corp. # # This is a sample HOSTS file used by Microsoft TCP/IP for Windows. # # This file contains the mappings of IP addresses to host names. Each # entry should be kept on an individual line. The IP address should # be placed in the first column followed by the corresponding host name. # The IP address and the host name should be separated by at least one # space. # # Additionally, comments (such as these) may be inserted on individual # lines or following the machine name denoted by a '#' symbol. # # For example: # # 102.54.94.97 rhino.acme.com # source server # 38.25.63.10 x.acme.com # x client host # localhost name resolution is handled within DNS itself. # 127.0.0.1 localhost # ::1 localhost ipconfig all: Connection-specific DNS Suffix: DNS Servers: 10.1.1.30 208.67.220.220

    Read the article

  • How Would I Restrict a Linux Binary to a Limited Amount of RAM?

    - by Ken S.
    I would like to be able to limit an installed binary to only be able to use up to a certain amount of RAM. I don't want it to get killed if it exceeds it, only that that would be the max amount that it could use. The problem I am facing is that I am running an Apache 2.2 server with PHP and some custom code that a developer is writing for us. The problem is that somewhere in there code they launch a PHP exec call that launches ImageMagick's 'convert' to create a resized image file. I'm not privy to a lot of details to the project or the code, but need to find a solution to keep them from killing the server until they can find a way to optimize the code. I had thought that I could do this with /etc/security/limits.conf and setting a limit on the apache user, but it seems to have no effect. This is what I used: www-data hard as 500 If I understand it correctly, this should have limited any apache user process to a maximum to 500kb, however, when I ran a test script that would chew up a lot of RAM, this actually got up to 1.5GB before I killed it. Here is the output of 'ps auxf' after the setting change and a system reboot: USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 5268 0.0 0.0 401072 10264 ? Ss 15:28 0:00 /usr/sbin/apache2 -k start www-data 5274 0.0 0.0 402468 9484 ? S 15:28 0:00 \_ /usr/sbin/apache2 -k start www-data 5285 102 9.4 1633500 1503452 ? Rl 15:29 0:58 | \_ /usr/bin/convert ../tours/28786/.…. www-data 5275 0.0 0.0 401072 5812 ? S 15:28 0:00 \_ /usr/sbin/apache2 -k start Next I thought I could do it with Apache's RlimitMEM setting, but get the same result of it not getting limited. Here is what I have in my apache.conf file: RLimitMEM 500000 512000 It wasn't until many hours later that I figured out that if the process actually reached that amount that it would die with an OOM error. Would love any ideas on how to set this limit so other things could function on the server, and all of them could play together nicely.

    Read the article

  • Windows Server 2012 licensing issue preventing RDP connections?

    - by QF_Developer
    I am witnessing an unusual behaviour on 1 of 5 Windows Server 2012 R2 machines (clean install) that is preventing any remote connections from being established via RDP. I have run through the prerequisites for RDP here but I am finding that any remote connection attempt instantly stops the "Windows Protection Service". When I check the event logs I see the following entry. The Software Protection Service has stopped Event ID: 903 Source: Security-SPP From what I have read Security-SPP is tasked with enforcing activation and licensing, it appears that RDP requires this service to be in the running state. Is it possible that I have inadvertently activated this instance of Windows with a key that has already been associated to another instance (We have 5 keys as part of an MSDN subscription)? Would this be sufficient to block RDP access? When I look under System Properties (Windows Activation) it states that Windows is activated and there are no other obvious indicators that there's a licensing issue. EDIT 1: I ran a Powershell script to display the product keys for all servers in order to check for any duplication. For the problematic server I am getting the message The RPC server is unavailable.

    Read the article

  • System x3550 M2 stuck on system initializing after firmware upgrades

    - by itmanager223
    Hey guys so i have been having this major issue for the last few hours now. I have a system x 3550M2 server and i ran the UEFI and IMM firmware upgrades within windows server 2008 R2 x64. All upgrades went fine and i was told to reboot. I performed the reboot cleanly using the OS restart option. Upon restarting it showed the system initializing screen and it stayed there for a good hour. After that hour i figured it froze and so i powered down and power up again. Now i can not boot back up to even see the IBM splash screen or the OS... I have tried switching the Jumpers to go to the backup UEFI and backup IMM and no luck. I have also reset the CMOS power and i have pressed the reset button 3 times on the light path and no luck. There are no lights light on the light path to indicate anything is broken. The only thing i see on the light path is the number 0.5. Any ideas guys i am quite stumped with this problem. Thanks a lot, Dani Cela

    Read the article

  • MySQL stops accepting connections over 3306, still working on localhost

    - by Ben Dilts
    I have a MySQL database that stopped accepting connections from my web server altogether. So I SSH'ed into the server and started checking its vitals. The hard disks had plenty of open space, and there was plenty of available memory and swap space. Nothing was eating up the CPU (close to 100% idle). I even connected to MySQL locally and ran a few queries without any issues. But SHOW PROCESSLIST only showed my own connection, no others. Worst of all, in the MySQL log, no errors even remotely coincided with the unavailability of the server. On the web server, I got an error saying "Lost connection to MySQL server during query" at the moment the unavailability started, followed by a bunch of "MySQL server has gone away" errors. There's only one other application on the server that accepts network connections, and I killed that one (in case it was holding too many open connections or something), but it didn't help. Finally I just restarted the MySQL process, and everything is (for now) working again. What else should I check in these circumstances? Any idea what the problem might be? And how might I verify that is in fact the problem?

    Read the article

  • Can I restore one of my user's profiles in Vista?

    - by Rod
    My youngest daughter uses my 4 year old laptop, which has Windows Vista installed. Somehow she got some Trojan (Vista Internet Security). (I'd love to know how that happened, seeing as how she is a standard user, and I have VIPRE as my AV.) Anyway, I ran a deep anti-virus scan using VIPRE, which identified it. I decided to delete everything that it identified. Now she cannot use anything in her profile. If she tries to bring up the browser, it recycles over and over again a dialog box asking which program to use. If I try to run any program at all, it doesn't know what to do. For example, it is totally lost trying to run the command line. If I bring up Windows Explorer and navigate to Windows\System32 and try to run the command line, or anything at all from there, it goes "Huh?" What in heck has happened?? Is it possible to fix this, and if so, how? As an aside, I can log into my account (my account on that machine is an administrator) and it works fine.

    Read the article

< Previous Page | 128 129 130 131 132 133 134 135 136 137 138 139  | Next Page >