Search Results

Search found 7126 results on 286 pages for 'wireless router'.

Page 132/286 | < Previous Page | 128 129 130 131 132 133 134 135 136 137 138 139  | Next Page >

  • unreachable subnet in one direction

    - by Carl Michaud
    I'm unable to route traffic to a subnet in my home. Here's my topology: INET <- Router A <- Router B <- WIFI AP where: Router A - ARRIS TG862G/CT (from comcast) - WAN DHCP, LAN 10.0.0.99 Router B - Linksys WRT400N with DD-WRT - WAN 10.0.0.12 , LAN 10.0.1.1 I was able to use DD-WRT to configure a static route for the 10.0.1.x network back to the 10.0.0.x network. But I'm not sure if i can do the reverse on the ARRIS router and was looking for suggestions on how to fix that. I've set things up this wasy because I am using OpenDNS to mange internet content for my kids and of course I wasn't able to configure DNS to my liking on Router A either. So at present I'm using Router A on 10.0.0.x to provide a private unfiltered WIFI AP (no ssid broadcast) that I use for netflix only and then I use router B to provide a filtered WIFI AP for the rest of my WIFI devices on 10.0.1.x. However I would like to be able to connect to my 10.0.1.x devices from the internet via dynamic dns; but I can't see anything behind router B this way. Thoughts?

    Read the article

  • Turn your laptop into a wireless Access Point with Windows 7!

    - by David Nudelman
    Windows 7 offers a very cool feature where you can connect multiple devices to any wired and wireless network connection (hotel, cable, 3G, UMTS, EDGE, WIFI, RJ45, Ethernet, etc.) by turning your own laptop into a wireless AP (Access Point) to relay those devices not directly connected to the internet. For this just enter these two commands to an elevated (right click on CMD.EXE, run as administrator): netsh wlan set hostednetwork mode=allow ssid=YOURFRIENDLYSSID key=SOMEPASSWORD netsh wlan start hostednetwork At this point, if Internet Connection Sharing (ICS) is setup, anyone can connect to your SoftAP (if they know the PWD of course) and the traffic will be sent through whatever adapter you want. You can actually bridge it across an entirely different adapter... or the same on a different Wifi LAN. A GUI to set this up can be downloaded for free here: http://www.connectify.me/

    Read the article

  • How to set up an ethernet and wireless network using /etc/network/interfaces?

    - by den-javamaniac
    Hi. Currently I have ethernet and wireless networks configured through a network manager (further NM) but it seems to be a bit buggy (I need a different MAC for ether which is never applied if using NM), so I would like to move all the network configs to interfaces file. I know (or can google for) configuration code, but I'm not sure how NM works and it looks like it overrides interface config. Please advice, how I can handle this issue. NOTE: I also would like to be able to locate and connect to various wireless networks but not sure how to do it.

    Read the article

  • How to get wireless and wired network working again on my Dell Inspiron 1501?

    - by Angelo Daul
    My wireless doesn't work with Ubuntu 12.04.(it worked with 10.04 LTS) I have a Dell Inspiron 1501. I followed the steps posted below:(from a similar tag, but...) sudo apt-get install --reinstall bcmwl-kernel-source broadcom-sta-common broadcom-sta-source echo "blacklist brcmsmac" | sudo tee -a /etc/modprobe.d/blacklist.conf echo "blacklist bcma" | sudo tee -a /etc/modprobe.d/blacklist.conf ....and now i have no Network device on my PC(wired or wireless) I can use wired conection if i start my laptop with a"previsious version of Linux"...2.26.43... I am a beginner in Linux These are my hardware: 05:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN [ 14e4:4311] (rev 01) 08:00.0 Ethernet controller [0200]: Broadcom Corporation BCM4401-B0 100Base-TX [ 14e4:170c] (rev 02)

    Read the article

  • Is there a small business router that shows bandwidth usage graphs in the admin panel?

    - by Robert Drake
    I support a large number of public libraries that are having their networks upgraded in response to a grant application. These libraries are generally home to between 6-15 computers and have little or no tech services either onsite or contracted remotely. In order to justify current and future purchases, a number of the libraries have requested routers that can provide bandwidth usage graphs that they can show to their managing boards. Is there a small business router that displays traffic graphs in the router administration web interface? The router needs to suppport DHCP and basic firewalling. No other features are required. Further, the reports just need to show overall trends. It is not necessary to show traffic by IP, by protocol/application, or by time of day. They just need an overall week to week, month to month, trend line. I'm familiar with MRTG/PRTG/tools that collect SNMP data from the router, but the libraries don't have the expertise for the configuration. I've considered installing the tomato firmware on some cheap home/home office routers, but if there's a commercial product that can be purchased that would be significantly simpler. Also the library boards would be much more likely to approve the purchase of a commercial product over a 'hacked' one. Any assistance would be appreciated.

    Read the article

  • Why is the link between my switch and my router always negotiating half-duplex mode?

    - by Massimo
    I have a Cisco 2950 switch which has one of its ports connected to an Internet router provided by my ISP; I have no access to the router configuration, but I manage the switch. If I leave all switch ports with their default setup (auto-negotiation of speed and duplex mode), this link always connects at 100 MBit/s, but in half-duplex mode. I've tried replacing the cable, and also moving the link to another switch port: the result is always the same. A different device connected to the same port (or to any switch port, really) shows no problem at all. It could be guesed that someone configured the router to only connect in half-duplex mode... BUT, here's the catch: if I manually force the switch port to full-duplex mode (duplex full in the interface configuration), the link goes up, stays up and is completely stable. So: The connection is not forced to half-duplex mode by the router, otherwise it would not connect at all if I force the switch end to full-duplex. There is no actual link problem, otherwise the full-duplex connection would not go up or would at least show some errors. But if I leave the port free to auto-negotiate, it always connects in half-duplex mode. Why?

    Read the article

  • Java Socket Connection is flooding network OR resulting in high ping

    - by user1461100
    i have a little problem with my java socket code. I'm writing an android client application which is sending data to a java multithreaded socket server on my pc through direct(!) wireless connection. It works fine but i want to improve it for mobile applications as it is very power consuming by now. When i remove two special lines in my code, the cpu usage of my mobile device (htc one x) is totally okay but then my connection seems to have high ping rates or something like that... Here is a server code snippet where i receive the clients data: while(true) { try { .... Object obj = in.readObject(); if(obj != null) { Class clazz = obj.getClass(); String className = clazz.getName(); if(className.equals("java.lang.String")) { String cmd = (String)obj; if(cmd.equals("dc")) { System.out.println("Client "+id+" disconnected!"); Server.connectedClients[id-1] = false; break; } if(cmd.substring(0,1).equals("!")) { robot.keyRelease(PlayerEnum.getKey(cmd,id)); } else { robot.keyPress(PlayerEnum.getKey(cmd,id)); } } } } catch .... Heres the client part, where i send my data in a while loop: private void networking() { try { if(client != null) { .... out.writeObject(sendQueue.poll()); .... } } catch .... when i write it this why, i send data everytime the while loop gets executed.. when sendQueue is empty, a null "Object" will be send. this results in "high" network traffic and in "high" cpu usage. BUT: all send comments are received nearly immediately. when i change the code to following: while(true) ... if(sendQueue.peek() != null) { out.writeObject(sendQueue.poll()); } ... the cpu usage is totally okay but i'm getting some laggs.. the commands do not arrive fast enough.. as i said, it works fine (besides cpu usage) if i'm sending data(with that null objects) every while execution. but i'm sure that this is very rough coding style because i'm kind of flooding the network. any hints? what am i doing wrong?? Thanks for your Help! Sincerly yours, maaft

    Read the article

  • How do I get rid of the Cisco CP one-time user message on a Cisco 2901 router?

    - by user65712
    I get this message on a new 2901 Cisco router: Cisco Configuration Professional (Cisco CP) is installed on this device and it provides the default username "cisco" for one-time use. If you have already used the username "cisco" to login to the router and your IOS image supports the "one-time" user option, then this username has already expired. You will not be able to login to the router with this username after you exit this session. It is strongly suggested that you create a new username with a privilege level of 15 using the following command. username <myuser> privilege 15 secret 0 <mypassword> Replace and with the username and password you want to use. It appears every time I login and everytime I show run. I already set up my username. How do I turn it off?

    Read the article

  • How much does a IPtables router slow down a connection?

    - by RayQuang
    Hi, I would like to know if introducing a new gateway in my network will slow things down. The question may sound unclear but here is an illustration: Before Installing gateway server Main Router <=> switches <=> servers after installing gateway Server Main Router <=> IPtables router <=> switches <=> servers My question is. How much will this delay incoming outgoing requests / file transfers. thanks, RayQuang

    Read the article

  • Is it possible to host a website with Apache HTTP through a ZyXEL EQ-660R modem and a Netgear WGT624v3 wireless router?

    - by Vortico
    Essentially, I have a spare desktop computer I'd like to turn into a web server, but my modem and wireless router are very difficult to work with. I installed Apache HTTP and successfully hosted a test page which can be accessed anywhere on the LAN. However, I'm having trouble setting up the server to be accessed from my external IP address. I was supplied with a ZyXEL EQ-660R DSL modem by my ISP (CenturyLink) and bought a Netgear WGT624v3 wireless router in which to connect my laptop and spare desktop. ZyXEL's website is no help, and I don't think much of the problem is with the Netgear router. I've played with many settings and have tried to forward port 80 from the modem, but I've had no luck. Could someone direct me toward a solution or recommendations for more promising hardware? Or should I admit defeat and explore other hobbies? :)

    Read the article

  • Port forwarding problem

    - by Steve
    I have a modem connecting to ADSL2 network and a router connecting to the modem. The rest of the machines all connect to the router. The modem has IP as 192.168.1.1 and the router's IP is 192.168.0.1. From the modem configuration, I can see that the modem thinks the router's IP is 192.168.1.2. I can visit the router by either using 192.168.0.1 or 192.168.1.2. Now I forward a port from the router to a private machine. It works. I can test it by typing 192.168.1.2 and it is redirected to the private machine. But if I use 192.168.0.1, it is still the router's configuration page. I also do a port forwarding on my modem. Since the modem sees only the router, I can only forward the port to the router's specific port. And I am thinking that by doing this, I can reach the private machine after two times port forwarding, once on the modem and once on the router. I also have a static public IP. I want to achieve the goal that when someone types the public IP, he will be redirected to the private machine. But when I use some online port forwarding tester, the result always says that the port is closed on the public IP. I have the questions: Why my router has two IPs? Why using one IP I can see the port forwarding result while using the other I cannot? I think the port forwarding only works when visiting from outside, rather than from both outside and inside. Otherwise, if I set port forwarding on my router/modem on port 80, I will never be able to see its original configuration page again. Everything is forwarded. Am I right? How can I achieve my goal described above? By achieve this, I will have a dedicated server of my own and the users can visit from the public IP. Anyone can correct me on any mistakes I made? I am using Netconn modem and D-Link DIR-300 router. Thank you very much for any help. Edit: Consider I have correctly setup the whole thing. Now I want to test my website by using public IP to visit it, but the port forwarding doesn't work. Does it consider that I am inside the local network and not using the port forwarding? If so, how can I do it? I ask my friends (outside my local network) to have a try and they can see the website. What should I do so that from the inside, I can do the testing? Thank you very much.

    Read the article

  • Port forwarding in C#/software possible? Isn't it only managed by the router?

    - by Rudi
    Isn't port forwarding managed by the router? Like, I've googled up some software applications that seem to port forward with great success, but it technically seems to be impossible. The packet must first go to the router. The router must forward it to the correct computer based on port forwarding rules. So how can a software application manage port forwarding if the packet must GO to the computer running this software application in the first place, meaning that port forwarding already is successful in the first place?

    Read the article

  • java.net.SocketException: Connection reset; No available router to destination

    - by adejuanc
    Sometimes a Weblogic Server will be unreachable, there could be several reasons, the server is hang, down, and thus not responding to a ping, or it could be related to a network issue.A possible point of failure in the network layer are firewalls. You should contact your network team if you have following messages: java weblogic.Admin -adminurl t3://adminServer.mydomain.com:7777 -username admin -password lockdown PINGFailed to connect to t3://adminServer.mydomain.com:7777: Destination unreachable; nested exception is:java.net.SocketException: Connection reset; No available router to destination A possible work around for the ping command is to use the HTTP protocol, instead of the t3 protocol. To enable this you must configure WebLogic to do HTTP tunneling. To enable, access the administration console, click servers-> server you want to reach-> protocols -> http -> enable Tunneling. no restart is necessary. And then, following command will work: java weblogic.Admin -adminurl http://adminServer.mydomain.com:7777 -username igmadmin -password l0ckdown PING

    Read the article

  • Internet stopped working after aircrack install (can still connect to my router). Suggestions?

    - by Dan
    I'm sure I did something dumb during the install for aircrack, but I have no clue what. Like I said, I can connect to my router (not trying to crack, simply logging into it), I just can't get internet access. To make this more interesting, the machine is dual booted and when I log into Windows I have zero issues. I feel like some driver may have been messed up in the process, but I'm not sure if that's a reasonable assumption or how exactly to check that. Also, can't revert to backup as there are none. Suggestions on how to trouble-shoot would be appreciated. EDIT: Hard-wiring to the wall I can get internet access on the Ubuntu side... PS- I know this is a stretch as far as fitting the Ubuntu section, but no other stackoverflow sites seemed to fit better.

    Read the article

  • How do I combine static and dynamic DHCP leases on a Cisco router?

    - by Brad
    Basically, what I need is super similar to the unanswered cisco forum question below: https://supportforums.cisco.com/message/3139749#3139749 I have a Cisco 850 Series router. I have configured a DHCP pool for the 10.0.0.0/24 network. I have excluded 10.0.0.1 - 10.0.0.99 from the DHCP pool. I want to add a static DHCP pool for stuff and I want DHCP to statically assign them the addresses of my choice below 100. Actually, I don't care what addresses I statically assign. They can be anything in the pool for all I care, I just want it to work. Why are you doing this? Just statically assign the IPs on the devices! I don't want to do this because I have some laptop users. They could obviously only use that static IP here. This isn't a problem if they could be bothered to change any location setting or something. They can't. So it HAS to be DHCP. It also has to be static IPs because I need to forward ports to them. I know, I know, this is weird but it's an apartment LAN/WLAN so this isn't exactly a typical use case. Relevant sections of config below: ip dhcp excluded-address 10.0.0.1 10.0.0.99 ! ip dhcp pool Internal-net import all network 10.0.0.0 255.255.255.0 default-router 10.0.0.1 domain-name 1770.local lease 7 ! ip dhcp pool static-pool import all origin file flash://staticmap default-router 10.0.0.1 domain-name 1770.local Contents of staticmap: *time* Aug 5 2010 09:00 AM *version* 2 !IP address Type Hardware address Lease expiration 10.0.0.100/24 1 001f.5b3e.d50a Infinite *end* You can see here I was trying addresses outside the excluded-address range to see if that would make any difference. My testing machine's MAC: mainframe:~ brad$ ifconfig en1 en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether 00:1f:5b:3e:d5:0a What shows up in the DHCP binding table: basestar#show ip dhcp binding Bindings from all pools not associated with VRF: IP address Client-ID/ Lease expiration Type Hardware address/ User name 10.0.0.112 0100.1f5b.3ed5.0a Aug 12 2010 10:06 AM Automatic What's up with the funny looking MAC in the DHCP binding table?? Is what I'm trying to accomplish basically impossible? Am I going about this the wrong way? All I want to to be able to port forward some ports to specific devices. The way I would do this with a consumer router is to do what I'm trying to do here; assign static DHCP to those devices then configure PAT for ports on those addresses.

    Read the article

  • Bluetooth firmware problem in Ubuntu 13.04

    - by chanzerre
    I have a [Dell Inspiron][1] 15R 5520 laptop. Bluetooth is not working at all. rfkill list all gives 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no dmesg|grep -i bluetooth gives [ 13.644428] Bluetooth: Core ver 2.16 [ 13.644445] Bluetooth: HCI device and connection manager initialized [ 13.644453] Bluetooth: HCI socket layer initialized [ 13.644455] Bluetooth: L2CAP socket layer initialized [ 13.644461] Bluetooth: SCO socket layer initialized [ 15.861363] Bluetooth: hci0 command 0x1003 tx timeout [ 15.903443] Bluetooth: can't load firmware, may not work correctly [ 17.332535] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 17.332538] Bluetooth: BNEP filters: protocol multicast [ 17.332544] Bluetooth: BNEP socket layer initialized [ 17.393768] Bluetooth: RFCOMM TTY layer initialized [ 17.393781] Bluetooth: RFCOMM socket layer initialized [ 17.393783] Bluetooth: RFCOMM ver 1.11 hciconfig gives hci0: Type: BR/EDR Bus: USB BD Address: E0:06:E6:D5:DB:46 ACL MTU: 1021:8 SCO MTU: 64:1 UP RUNNING PSCAN ISCAN RX bytes:687 acl:0 sco:0 events:56 errors:0 TX bytes:2024 acl:0 sco:0 commands:52 errors:0 I have visited the site http://wireless.kernel.org/en/users/Drivers/b43 and according to it lspci -vnn -d 14e4: gives 08:00.0 Network controller [0280]: Broadcom Corporation BCM43142 802.11b/g/n [14e4:4365] (rev 01) Subsystem: Dell Wireless 1704 802.11n + BT 4.0 [1028:0016] Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at c1500000 (64-bit, non-prefetchable) [size=32K] Capabilities: <access denied> Kernel driver in use: wl So I got my PCI-ID as 14e4:4365 which it says is not supported. The alternative is wl. What should I do? My Wi-Fi is working normally without any problems, but Bluetooth is not working. sudo dpkg -i wireless-bcm43142-dkms_6.20.55.19-1_amd64.deb gives following error (Reading database ... 208543 files and directories currently installed.) Unpacking wireless-bcm43142-dkms (from wireless-bcm43142-dkms_6.20.55.19-1_amd64.deb) ... Setting up wireless-bcm43142-dkms (6.20.55.19-1) ... Loading new wireless-bcm43142-6.20.55.19 DKMS files... Building only for 3.8.0-23-generic Building initial module for 3.8.0-23-generic Traceback (most recent call last): File "/usr/share/apport/package-hooks/dkms_packages.py", line 22, in <module> import apport ImportError: No module named apport Error! Bad return status for module build on kernel: 3.8.0-23-generic (x86_64) Consult /var/lib/dkms/wireless-bcm43142/6.20.55.19/build/make.log for more information.

    Read the article

  • Ericsson f3507g WWAN (3G Broadband) and AT commands

    - by JD
    I have a lenovo x200t tablet with WWAN built into it. I'm trying to connect to the internet using AT commands and a C# program which I am making so that the program can connect to the net and upload information on demand. I don't want to use Lenovo's "Access Connections" as it is too complicated for the end user. So far I have been able to use terminal to turn the card on and off, ring landlines and send SMS messages. However I can't seem to access the internet using it. I could access the net through it before I removed "Access Connections" software/bloatware. The commands I am using to try and access the net are: Connect on COM7 to the modem Send initialisation string "AT+CFUN=1" Send AT*ENAP=1,1 as suggested here (http://www.thinkwiki.org/wiki/Ericsson%5FF3507g%5FMobile%5FBroadband%5FModule) Windows says it is "Identifying" the network and a yellow exclamation mark appears on the networking icon in the task bar, but the connection fails and drops off. An IP is assigned to the "Local Area Connection 2" of 169.254.1.192 with a subnet of 255.255.0.0 - no gateway or DNS. Definately no net connection... Anyone got any ideas?

    Read the article

  • decoding 802.11 b

    - by stan
    I have a raw grabbed data from spectrometer that was working on wifi (802.11b) channel 6. (two laptops in ad-hoc ping each other). I would like to decode this data in matlab. I see them as complex vector with 4.6 mln of complex samples. I see their spectrum quite nice. I am looking document a bit less complicated as IEEE 802.11 standard (which I have). I can share measurement data to other people.

    Read the article

  • Vehicle 2 Vehicle Communication Questions

    - by pinnacler
    I have a rare opportunity to meet the man in charge of implementing vehicle 2 vehicle communication for the US Department of Transportation with 2 others in a few hours. Do YOU have any questions for him? I know this is a little outside the normal, but this is a 'reverse' thread and I felt he has some great knowledge on the subject that I want to share with this community. I'll post his answers later today to his questions. Ask about V2V implementation, privacy issues, use cases, or if you've thought of a great way to use V2V and want me to share it with him, he can at least think about it. He is in charge of panel that creates the standard. Or anything else...

    Read the article

  • network windows programming problem

    - by Jayjitraj
    I want to write program which will connect to a network for some amount of time in seconds. Then it disconnects from it and it should be that much faster than the other application (?) should not feel it is disconnected. Which layer should I program at? I know how to disconnect and connect to the network so any suggestion will be helpful...... thanks in advance....

    Read the article

  • Verizon SongID - How is it programmed?

    - by CheeseConQueso
    For anyone not familiar with Verizon's SongID program, it is a free application downloadable through Verizon's VCast network. It listens to a song for 10 seconds at any point during the song and then sends this data to some all-knowing algorithmic beast that chews it up and sends you back all the ID3 tags (artist, album, song, etc...) The first two parts and last part are straightforward, but what goes on during the processing after the recorded sound is sent? I figure it must take the sound file (what format?), parse it (how? with what?) for some key identifiers (what are these? regular attributes of wave functions? phase/shift/amplitude/etc), and check it against a database. Everything I find online about how this works is something generic like what I typed above. From audiotag.info This service is based on a sophisticated audio recognition algorithm combining advanced audio fingerprinting technology and a large songs' database. When you upload an audio file, it is being analyzed by an audio engine. During the analysis its audio “fingerprint” is extracted and identified by comparing it to the music database. At the completion of this recognition process, information about songs with their matching probabilities are displayed on screen.

    Read the article

  • Voting software with remote units - architectural questions

    - by David Neale
    I'm looking at designing some software that registers live votes (let's say A,B,C or D). The vote needs to be picked up and processed by a .NET engine. The remote voting units should be as small as possible. What form of data transmission should be used for the voting? The data is obviously very simple but there is a need to make sure each unit can only vote once per question. How would the data be received by the computer running the software?

    Read the article

  • winwindows programming problem

    - by Jayjitraj
    I want to write programming which will connect to a network for some second then disconnect from it and it should be that much fast that other application should not fill it is disconnected so on which layer should i program i know how to disconnect and connect to the network so any suggestion ...... thanks in advance....

    Read the article

< Previous Page | 128 129 130 131 132 133 134 135 136 137 138 139  | Next Page >