Search Results

Search found 24515 results on 981 pages for '24 bit'.

Page 133/981 | < Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >

  • DNAT to 127.0.0.1 with iptables / Destination access control for transparent SOCKS proxy

    - by cdauth
    I have a server running on my local network that acts as a router for the computers in my network. I want to achieve now that outgoing TCP requests to certain IP addresses are tunnelled through an SSH connection, without giving the people from my network the possibility to use that SSH tunnel to connect to arbitrary hosts. The approach I had in mind until now was to have an instance of redsocks listening on localhost and to redirect all outgoing requests to the IP addresses I want to divert to that redsocks instance. I added the following iptables rule: iptables -t nat -A PREROUTING -p tcp -d 1.2.3.4 -j DNAT --to-destination 127.0.0.1:12345 Apparently, the Linux kernel considers packets coming from a non-127.0.0.0/8 address to an 127.0.0.0/8 address as “Martian packets” and drops them. What worked, though, was to have redsocks listen on eth0 instead of lo and then have iptables DNAT the packets to the eth0 address instead (or using a REDIRECT rule). The problem about this is that then every computer on my network can use the redsocks instance to connect to every host on the internet, but I want to limit its usage to a certain set of IP addresses only. Is there any way to make iptables DNAT packets to 127.0.0.1? Otherwise, does anyone have an idea how I could achieve my goal without opening up the tunnel to everyone? Update: I have also tried to change the source of the packets, without any success: iptables -t nat -A POSTROUTING -p tcp -s 192.168.1.0/24 -d 1.2.3.4 -j SNAT --to-source 127.0.0.1 iptables -t nat -A POSTROUTING -p tcp -s 192.168.1.0/24 -d 127.0.0.1 -j SNAT --to-source 127.0.0.1

    Read the article

  • Changing subnet-mask of class-c network host to 255.255.0.0

    - by Prashant Mandhare
    We have a existing class-c network with IP address range 11.22.33.44/24 (just for example). My domain controller has been configured within this subnet. So all servers within this subnet have subnet mask configured to 255.255.255.0. Now we have got a new subnet with IP address 11.22.88.99/24 (note that only last 2 octets have changed). I want all new hosts in this new subnet to join my existing DC. For this we have configured firewall properly so allow this. (so there is no issue with firewall). But initially I was not able to join hosts in new subnet in existing domain. Later I doubted on subnet mask used in domain controller (255.255.255.0) and for testing purpose I changed it to 255.255.0.0, it worked like charm, i was able to join subnet-2 hosts in subnet-1 domain. Now i am wondering whether it will be good practice to change subnet mask of a class-c network to 255.255.0.0? Can any issues arise due to this? Experts please provide your opinion.

    Read the article

  • Uknown nginx Error Messages

    - by Sparsh Gupta
    Hello, I am getting some nginx errors as I can see them in my error.log which I am unable to understand. They look like: ERRORS: 2011/03/13 21:48:21 [crit] 14555#0: *323314343 open() "/usr/local/nginx/proxy_temp/0/95/0000000950" failed (13: Permission denied) while reading upstream, client: XX.XX.XX.XX, server: , request: "GET /abc.jpg 2 HTTP/1.0", upstream: "http://192.168.162.141:80/abc.jpg", host: "example.com", referrer: "http://domain.com" 2011/03/13 22:00:07 [crit] 14552#0: *324171134 open() "/usr/local/nginx/proxy_temp/1/95/0000000951" failed (13: Permission denied) while reading upstream, client: XX.XX.XX.XY, server: , request: "GET mno.png HTTP/1.1", upstream: "http://192.168.162.141:80/mno.png", host: "example.com", referrer: "http://domain2.com" I also looked at these locations but found that there is no file by this name. root@li235-57:/var/log/nginx# /usr/local/nginx/proxy_temp/1/ 00/ 01/ 02/ 03/ 04/ 05/ 06/ 07/ 08/ 09/ 10/ 11/ 12/ 13/ 14/ 15/ 16/ 17/ 18/ 19/ 20/ 21/ 22/ 23/ 24/ 25/ 26/ 27/ 28/ 29/ 30/ 31/ 32/ 33/ 34/ 35/ 36/ 37/ root@li235-57:/var/log/nginx# ls /usr/local/nginx/proxy_temp/0/ 01/ 02/ 03/ 04/ 05/ 06/ 07/ 08/ 09/ 10/ 11/ 12/ 13/ 14/ 15/ 16/ 17/ 18/ 19/ 20/ 21/ 22/ 23/ 24/ 25/ 26/ 27/ 28/ 29/ 30/ 31/ 32/ 33/ 34/ 35/ 36/ 37/ Can someone help me whats going on / how can I debug this more and better fix this Thanks

    Read the article

  • GRUB doesn't recognize partitions on one harddisk

    - by knizz
    I have a dualboot computer with Windows Vista (on hd0) and Ubuntu 9.10. The bootloader is GRUB and the windows bootloader lets me decide between Vista and Ubuntu-Installation (broken WuBi). But now (i don't know why that changed) I can't use start the windows-bootloader anymore. I tried "ls" on the grub-prompt and it gave me a list like: (hd0) (hd1) (hd1,0) (hd1,1) (hd1,2) ... (fd0) It recognizes all partitions of hd1 (the ubuntu-harddisk) but not of hd0(the win-disk). .. WHY? Here is the result of the "boot info script" for the technical details: Boot Info Script 0.55 dated February 15th, 2010 ============================= Boot Info Summary: ============================== => Grub 2 is installed in the MBR of /dev/sda and looks for (UUID=a7c510e3-2399-437b-ab92-fa609e48d63f)/boot/grub. => No boot loader is installed in the MBR of /dev/sdb sda1: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Windows Vista Boot files/dirs: /bootmgr /Boot/BCD /Windows/System32/winload.exe /wubildr.mbr /wubildr sda2: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files/dirs: sdb1: _________________________________________________________________________ File system: Boot sector type: Unknown Boot sector info: Mounting failed: mount: unbekannter Dateisystemtyp „“ sdb2: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files/dirs: sdb3: _________________________________________________________________________ File system: Bios Boot Partition Boot sector type: - Boot sector info: sdb4: _________________________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Ubuntu 9.10 Boot files/dirs: /boot/grub/grub.cfg /etc/fstab /boot/grub/core.img sdb5: _________________________________________________________________________ File system: swap Boot sector type: - Boot sector info: =========================== Drive/Partition Info: ============================= Drive: sda ___________________ _____________________________________________________ Platte /dev/sda: 640.1 GByte, 640135028736 Byte 255 Köpfe, 63 Sektoren/Spuren, 77825 Zylinder, zusammen 1250263728 Sektoren Einheiten = Sektoren von 1 × 512 = 512 Bytes Disk identifier: 0x52554d66 Partition Boot Start End Size Id System /dev/sda1 * 2,048 307,202,047 307,200,000 7 HPFS/NTFS /dev/sda2 307,202,048 1,250,258,943 943,056,896 7 HPFS/NTFS Drive: sdb ___________________ _____________________________________________________ Platte /dev/sdb: 640.1 GByte, 640135028736 Byte 255 Köpfe, 63 Sektoren/Spuren, 77825 Zylinder, zusammen 1250263728 Sektoren Einheiten = Sektoren von 1 × 512 = 512 Bytes Disk identifier: 0x00000000 Partition Boot Start End Size Id System /dev/sdb1 1 1,250,263,727 1,250,263,727 ee GPT GUID Partition Table detected. Partition Start End Size System /dev/sdb1 34 262,177 262,144 Microsoft Windows /dev/sdb2 262,178 1,131,253,933 1,130,991,756 Linux or Data /dev/sdb3 1,131,253,934 1,131,255,887 1,954 Bios Boot Partition /dev/sdb4 1,131,255,888 1,245,312,528 114,056,641 Linux or Data /dev/sdb5 1,245,312,529 1,250,263,694 4,951,166 Linux Swap blkid -c /dev/null: ____________________________________________________________ Device UUID TYPE LABEL /dev/sda1 AE1440441440122F ntfs /dev/sda2 3AE66E4DE66E0A09 ntfs data /dev/sdb2 5419D16119DAA4DE ntfs LaufwerkD /dev/sdb4 a7c510e3-2399-437b-ab92-fa609e48d63f ext4 /dev/sdb5 60a0143a-e01b-450a-bbd1-f22059e47b65 swap ============================ "mount | grep ^/dev output: =========================== Device Mount_Point Type Options /dev/sdb4 / ext4 (rw,errors=remount-ro) =========================== sdb4/boot/grub/grub.cfg: =========================== # # DO NOT EDIT THIS FILE # # It is automatically generated by /usr/sbin/grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s /boot/grub/grubenv ]; then have_grubenv=true load_env fi set default="0" if [ ${prev_saved_entry} ]; then saved_entry=${prev_saved_entry} save_env saved_entry prev_saved_entry= save_env prev_saved_entry fi insmod ext2 set root=(hd1,4) search --no-floppy --fs-uuid --set a7c510e3-2399-437b-ab92-fa609e48d63f if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=640x480 insmod gfxterm insmod vbe if terminal_output gfxterm ; then true ; else # For backward compatibility with versions of terminal.mod that don't # understand terminal_output terminal gfxterm fi fi if [ ${recordfail} = 1 ]; then set timeout=-1 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/white ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### menuentry "Ubuntu, Linux 2.6.31-20-generic" { recordfail=1 if [ -n ${have_grubenv} ]; then save_env recordfail; fi set quiet=1 insmod ext2 set root=(hd1,4) search --no-floppy --fs-uuid --set a7c510e3-2399-437b-ab92-fa609e48d63f linux /boot/vmlinuz-2.6.31-20-generic root=UUID=a7c510e3-2399-437b-ab92-fa609e48d63f ro quiet splash initrd /boot/initrd.img-2.6.31-20-generic } menuentry "Ubuntu, Linux 2.6.31-20-generic (recovery mode)" { recordfail=1 if [ -n ${have_grubenv} ]; then save_env recordfail; fi insmod ext2 set root=(hd1,4) search --no-floppy --fs-uuid --set a7c510e3-2399-437b-ab92-fa609e48d63f linux /boot/vmlinuz-2.6.31-20-generic root=UUID=a7c510e3-2399-437b-ab92-fa609e48d63f ro single initrd /boot/initrd.img-2.6.31-20-generic } menuentry "Ubuntu, Linux 2.6.31-14-generic" { recordfail=1 if [ -n ${have_grubenv} ]; then save_env recordfail; fi set quiet=1 insmod ext2 set root=(hd1,4) search --no-floppy --fs-uuid --set a7c510e3-2399-437b-ab92-fa609e48d63f linux /boot/vmlinuz-2.6.31-14-generic root=UUID=a7c510e3-2399-437b-ab92-fa609e48d63f ro quiet splash initrd /boot/initrd.img-2.6.31-14-generic } menuentry "Ubuntu, Linux 2.6.31-14-generic (recovery mode)" { recordfail=1 if [ -n ${have_grubenv} ]; then save_env recordfail; fi insmod ext2 set root=(hd1,4) search --no-floppy --fs-uuid --set a7c510e3-2399-437b-ab92-fa609e48d63f linux /boot/vmlinuz-2.6.31-14-generic root=UUID=a7c510e3-2399-437b-ab92-fa609e48d63f ro single initrd /boot/initrd.img-2.6.31-14-generic } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### menuentry "Windows Vista (loader) (on /dev/sda1)" { insmod ntfs set root=(hd0,1) search --no-floppy --fs-uuid --set ae1440441440122f chainloader +1 } ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### =============================== sdb4/etc/fstab: =============================== # /etc/fstab: static file system information. # # Use 'blkid -o value -s UUID' to print the universally unique identifier # for a device; this may be used with UUID= as a more robust way to name # devices that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc defaults 0 0 # / was on /dev/sdb4 during installation UUID=a7c510e3-2399-437b-ab92-fa609e48d63f / ext4 errors=remount-ro 0 1 # swap was on /dev/sdb5 during installation UUID=60a0143a-e01b-450a-bbd1-f22059e47b65 none swap sw 0 0 /dev/scd0 /media/cdrom0 udf,iso9660 user,noauto,exec,utf8 0 0 /dev/fd0 /media/floppy0 auto rw,user,noauto,exec,utf8 0 0 =================== sdb4: Location of files loaded by Grub: =================== 583.8GB: boot/grub/core.img 583.8GB: boot/grub/grub.cfg 579.7GB: boot/initrd.img-2.6.31-14-generic 580.0GB: boot/initrd.img-2.6.31-20-generic 579.7GB: boot/vmlinuz-2.6.31-14-generic 579.8GB: boot/vmlinuz-2.6.31-20-generic 580.0GB: initrd.img 579.7GB: initrd.img.old 579.8GB: vmlinuz 579.7GB: vmlinuz.old =========================== Unknown MBRs/Boot Sectors/etc ======================= Unknown BootLoader on sdb1 00000000 54 34 dc 3b 8b ff 6c fa 3e 59 3d 24 25 af 5f 9b |T4.;..l.>Y=$%._.| 00000010 72 f8 36 3d 56 30 22 fd c6 08 5e 39 7f dc 29 48 |r.6=V0"...^9..)H| 00000020 48 e5 24 52 77 b0 fc 64 b6 ce 48 c3 07 ce b5 81 |H.$Rw..d..H.....| 00000030 06 68 60 4f 6e fb 83 92 df 3a 54 b9 df 21 2a cd |.h`On....:T..!*.| 00000040 1e 2f e2 49 fe cf 81 2d 52 17 1a 4e 66 b4 f3 f0 |./.I...-R..Nf...| 00000050 41 25 e3 96 26 28 fe 19 61 72 75 f8 40 a3 b7 ef |A%..&(..aru.@...| 00000060 5f 79 dc cb 28 44 44 7c 9b 9a 7b 6c 4b 4b 60 0f |_y..(DD|..{lKK`.| 00000070 a9 97 87 bc 85 9f db bb d2 1a 88 9f aa 49 18 d5 |.............I..| 00000080 92 2d db 7e fe f7 8d 7a 18 c0 33 c5 bd 7a 46 07 |.-.~...z..3..zF.| 00000090 c8 27 13 66 94 49 62 9f bc 99 56 55 25 fb 94 a9 |.'.f.Ib...VU%...| 000000a0 3f b2 a7 0a 87 d0 a4 4e 51 f1 09 02 c4 29 eb ff |?......NQ....)..| 000000b0 26 3b 51 3e 5a 0c db ee a6 57 a7 c3 ba a1 74 90 |&;Q>Z....W....t.| 000000c0 ee 70 08 18 cc b8 d0 22 ce 96 c7 cb 68 40 98 20 |.p....."....h@. | 000000d0 49 3d 07 ec df d1 8d cf 19 bc 42 90 70 24 01 b4 |I=........B.p$..| 000000e0 28 cf c6 50 d3 95 5a 1b 18 15 33 c7 b2 a8 95 92 |(..P..Z...3.....| 000000f0 bb 93 fe 18 2b 81 c1 6b 9c 30 f1 65 50 6a 80 3d |....+..k.0.ePj.=| 00000100 74 37 a8 59 a6 51 8a 63 b6 d8 16 9f a9 47 2a 7c |t7.Y.Q.c.....G*|| 00000110 04 a7 fe 69 47 02 bf e9 b7 1b 7a ea 60 5c 3c 53 |...iG.....z.`\<S| 00000120 5b 10 78 dc 4d d2 a8 22 30 45 37 fb 56 06 9f 06 |[.x.M.."0E7.V...| 00000130 aa df cf 87 3a 3e cf 72 f2 e5 a6 c6 aa e2 7c 1c |....:>.r......|.| 00000140 64 c2 fc 80 ce 02 fc 7f 0f c6 60 81 bf cd 3b 5a |d.........`...;Z| 00000150 37 a5 38 1b 0c 1b 39 2e d6 f6 3d a2 36 e5 87 c3 |7.8...9...=.6...| 00000160 17 b5 fd ee 33 c7 ce a3 d9 c2 57 dc ee 85 48 9d |....3.....W...H.| 00000170 33 60 02 cd c5 83 44 44 ea b6 07 25 0a 4b a6 6e |3`....DD...%.K.n| 00000180 fc 51 42 cd 84 0b 65 b6 19 a1 e5 b2 eb 14 0c fa |.QB...e.........| 00000190 24 77 f5 44 6e 5d 39 dd b6 8e cc f8 30 fe 21 46 |$w.Dn]9.....0.!F| 000001a0 9c ff 95 c6 c7 b5 0a df 54 ca d2 ac bc 64 d0 97 |........T....d..| 000001b0 94 54 d9 29 0f 91 60 20 c3 e4 53 c2 b0 e4 40 72 |.T.)..` ..S...@r| 000001c0 7e 25 bc 81 06 ad 05 46 14 a7 e6 71 6b 5c db 9c |~%.....F...qk\..| 000001d0 0a 5e 76 23 ae 06 01 36 98 21 65 2c 90 e7 4b 1a |.^v#...6.!e,..K.| 000001e0 2a 2d 80 a5 48 db 9e 14 e0 9f e9 aa 00 e3 77 32 |*-..H.........w2| 000001f0 0f fd 94 db 55 a6 64 46 be ae ca de da ee 89 68 |....U.dF.......h| 00000200 =======Devices which don't seem to have a corresponding hard drive============== sdc sdd sde

    Read the article

  • Endian Destination NAT

    - by Ben Swinburne
    I have installed Endian Community Firewall 2.3 and am clearly misunderstanding/doing something wrong with it. I'm trying to create some destination NAT rules to allow incoming connections to various services within the network. Router - RED I/F - x.x.x.x Router - GREEN I/F - 192.168.11.253 ECF - RED I/F - 192.168.11.254/24 ECF - GREEN I/F - 192.168.12.254/24 Target server - 192.168.12.1 Please ignore the haphazard choice of subnets and addresses- I'm trying to quickly plop Endian into an existing network before a complete rework in 6-12 months so for now. Everything works except destination NAT, so outgoing connections are fine, the routes between the two subnets are OK etc. I want to create various incoming NATs but let's take for the sake of argument, SMTP port 25 from the Internet to Target server 192.168.12.1. I've tried almost every combination of options in the Destination NAT section to achieve this and clearly am doing something wrong. I suspect my confusion must be somewhere in the Access From and/or Target section. The rest seems OK Filter Policy = Allow Service = SMTP Protocol = TCP Port = 25 Translate to type = IP DNAT Policy = NAT Insert IP = 192.168.12.1 Port Range = 25 Enabled = Checked Position = First I can't work out what I'm doing wrong, or am I doing it right and it's just not working!? Any help would be greatly appreciated.

    Read the article

  • Apache MaxClients reaching max and locking the server

    - by Rodrigo Sieiro
    Hi. I currently have an Apache2 server running with mpm-prefork and mod_php on a OpenVZ VPS with 512M real / 1024M burstable RAM (no swap). After running some tests, I found that the maximum process size Apache gets is 23M, so I've set MaxClients to 25 (23M x 25 = 575 MB, ok for me). I decided to run some load tests on my server, and the results left me puzzled. I'm using ab on my desktop machine requesting the main page from a wordpress blog. When I run ab with 24 concurrent connections, everything seems fine. Sure, CPU goes up, free RAM goes down, and the result is about 2-3s response time per request. But if I run ab with 25 concurrent connections (my server limit), Apache just hangs after a couple of seconds. It starts processing the requests, then it stops responding, CPU goes back to 100% idle and ab times out. Apache log says it reached MaxClients. When this happens, Apache keeps itself locked up with 25 running processes (they're all in "W" if I check server status) and only after the TimeOut setting the processes start to die and the server starts responding again (in my case it's set to 45). My question: is that expected behaviour? Why Apache just dies when it reaches MaxClients? If it works with 24 connections, shouldn't it work with 25, just taking maybe more time to respond each request and queueing up the rest? It sounds kinda strange to me that any kid running ab can alone kill a webserver just by setting the concurrent connections to the servers MaxClients.

    Read the article

  • Apache reaching MaxClients and locking the server

    - by Rodrigo Sieiro
    Hi. I currently have an Apache2 server running with mpm-prefork and mod_php on a OpenVZ VPS with 512M real / 1024M burstable RAM (no swap). After running some tests, I found that the maximum process size Apache gets is 23M, so I've set MaxClients to 25 (23M x 25 = 575 MB, ok for me). I decided to run some load tests on my server, and the results left me puzzled. I'm using ab on my desktop machine requesting the main page from a wordpress blog. When I run ab with 24 concurrent connections, everything seems fine. Sure, CPU goes up, free RAM goes down, and the result is about 2-3s response time per request. But if I run ab with 25 concurrent connections (my server limit), Apache just hangs after a couple of seconds. It starts processing the requests, then it stops responding, CPU goes back to 100% idle and ab times out. Apache log says it reached MaxClients. When this happens, Apache keeps itself locked up with 25 running processes (they're all in "W" if I check server status) and only after the TimeOut setting the processes start to die and the server starts responding again (in my case it's set to 45). My question: is that expected behaviour? Why Apache just dies when it reaches MaxClients? If it works with 24 connections, shouldn't it work with 25, just taking maybe more time to respond each request and queueing up the rest? It sounds kinda strange to me that any kid running ab can alone kill a webserver just by setting the concurrent connections to the servers MaxClients.

    Read the article

  • Problem setting command-line console resolution. vbeinfo in grub2 does not report all resolutions

    - by Kent
    I have a Asus EEE PC 1005P which I installed a Command-line system on using the Alternate Installer CD of Ubuntu Lucid Lynx. Altough I think this is a general linux and grub2 question. I do not have (or want) the X Window System installed. I want to change my console screen resolution (not inside X) to 1024x600. But it isn't reported when I use vbeinfo inside grub: grub> vbeinfo VBE info: version: 3.0 OEM software rev: 1.0 total memory: 8128 KiB List of compatible video modes: Legend: P=Packed pixel, D=Direct color, mask/pos=R/G/B/reserved 0x112: 640 x 480 x 32 Direct, mask: 8/8/8/8 pos: 16/8/0/24 0x114: 800 x 600 x 16 Direct, mask: 5/6/5/0 pos: 11/5/0/0 0x115: 800 x 600 x 32 Direct, mask: 8/8/8/8 pos: 16/8/0/24 0x101: 640 x 480 x 8 Packed 0x103: 800 x 600 x 8 Packed 0x111: 640 x 480 x 16 Direct, mask: 5/6/5/0 pos: 11/5/0/0 Configured VBE mode (vbe_mode) = ox101 grub> Relevant parts of sudo lspci -v: ... ... 00:02.0 VGA compatible controller: Intel Corporation N10 Family Integrated Graphics Controller Subsystem: ASUSTeK Computer Inc. Device 83ac Flags: bus master, fast devsel, latency 0, IRQ 28 ... Kernel driver in use: i915 Kernel modules: i915 00:02.1 Display controller: Intel Corporation N10 Family Integrated Graphics Controller Subsystem: ASUSTeK Computer Inc. Device 83ac Flags: bus master, fast devsel, latency 0, IRQ 28 ... ... ... Any ideas on how I can set the console resultion like I want it?

    Read the article

  • strange Postfix logwatch log summary on my ubuntu vps

    - by DannyRe
    Hi I would be very thankful if someone could help me on explaining this logwatch summary of my postfix installation on my ubuntu 10.04 vps. I dont really know if this might be a normal log file because of the many authentication failed entries and foreign IP addresses. Any advise for a novice? Thx! ****** Summary ************************************************************************************* 113 SASL authentication failed 195 Miscellaneous warnings 8.419K Bytes accepted 8,621 8.419K Bytes delivered 8,621 ======== ================================================== 3 Accepted 60.00% 2 Rejected 40.00% -------- -------------------------------------------------- 5 Total 100.00% ======== ================================================== 2 5xx Reject relay denied 100.00% -------- -------------------------------------------------- 2 Total 5xx Rejects 100.00% ======== ================================================== 116 Connections 1 Connections lost (inbound) 116 Disconnections 3 Removed from queue 3 Delivered 1 Hostname verification errors ****** Detail (10) ********************************************************************************* 113 SASL authentication failed -------------------------------------------------------------- 113 92.24.80.207 host-92-24-80-207.ppp.as43234.net 113 LOGIN 113 generic failure 195 Miscellaneous warnings ------------------------------------------------------------------ 113 SASL authentication failure: cannot connect to saslauthd server: Permission denied 41 inet_protocols: IPv6 support is disabled: Address family not supported by protocol 41 inet_protocols: configuring for IPv4 support only 2 5xx Reject relay denied ----------------------------------------------------------------- 1 46.242.103.110 unknown 1 [email protected] 1 114.42.142.103 114-42-142-103.dynamic.hinet.net 1 [email protected] 1 Connections lost (inbound) -------------------------------------------------------------- 1 After RCPT 3 Delivered ------------------------------------------------------------------------------- 3 myhost.xx 1 Hostname verification errors ------------------------------------------------------------ 1 Name or service not known 1 46.242.103.110 broadband-46-242-103-110.nationalcablenetworks.ru === Delivery Delays Percentiles ============================================================ 0% 25% 50% 75% 90% 95% 98% 100%

    Read the article

  • Inter-vlan routing issues

    - by DKNUCKLES
    I've been brought in to help administer a network and I've run into an issue - I'm not sure why this one is beyond me, however I figure an extra set of eyes on the problem may help resolve the issue. I have an HP MSM720 controller and at the time I'm trying to set up a basic hotspot set up with access points. For the time being I'm just looking to have people authenticate with a PSK and access the internet and other resources (namely printers) on other vlans. The user authenticates and the DHCP server on the controller gives them a 192.168.1.0/24 address. They are able to successfully browse the internet and ping machines on other networks, however they are unable to print to network printers that sit on the same LANs as the very computers that wireless clients can ping. The (extremely simplified) topology is as follows Computers on the wireless 192.168.1.1 network are able to ping computers on the 192.168.0.0 network, however cannot ping or print to the printers on the same network. I'm baffled and I have no idea why this is the case. Can anyone shed some light on this for me? Can someone spot the error of my configuration? EDIT : It should be noted that for whatever reason other computers on the 10.0.100.0/24 network cannot even ping the gateway of the Wireless Access network (192.168.1.1) - I'm not sure if this is relevant. These are the VLANS listed on the controller.

    Read the article

  • Selenium server causes crazy load on server - how to prevent?

    - by Eric
    I'm running this linux: Linux host.themepark.com 2.6.32-220.4.1.el6.x86_64 #1 SMP Tue Jan 24 02:13:44 GMT 2012 x86_64 x86_64 x86_64 GNU/Linux And I run the Selenium stand-alone server on my box with this command: java -jar /home/l/cron/selenium-server-standalone-2.24.1.jar > /logs/selenium.log 2>&1 & Here's the problem: as soon as I do that, the server load starts skyrocketing. I even went back and downloaded older versions of the Selenium server, but same results with 2.23.1, 2.23.0, and 2.19.0. Note that the server load starts going nuts before I issue ANY commands to Selenium or do anything else. All I'm doing is firing up the server, per the command above. This used to work perfectly on my server without causing massive server load, so something has changed, but I'm not sure what. My server is a managed VPS so I don't know if there is some kind of auto-update script that kicked in or what... but it's a problem. (Incidentally, even though the server load climbs like crazy, everything still works: after firing up Selenium, my server creates a screen with Xvfb so Firefox will be happy, then a PHP script talks to Selenium to do what it needs to do before shutting everything down. It takes a LONG time, and the load gets all the way up to 8 [!!!] before it is finished, which kills my web server and makes the main site horribly unresponsive... but it does get everything done.) Any suggestions for what is going on, why it's started doing this and/or, most importantly, how I can make Selenium not kill the server when it starts up... would be GREATLY appreciated!

    Read the article

  • Passing OpenVPN road-warrior traffic through tunnel pfsense

    - by Chris
    I have a local LAN (10.100.100.0/24) and OpenVPN road-warriors (10.99.99.0/24). pfSense is regulating all this as follows: LAN: 10.100.100.105 WAN: 10.100.99.1 (connected to DSL Router which connects to internet). OPT1: 10.99.99.0 (OpenVPN tun0). There is an IPSec connection between my office and another office where my LAN can work on a specific IP address (sql server to be exact) on 192.168.30.41. My problem is that I wish my OpenVPN road-warrior clients to be able to use the IPSec service on 192.168.30.41 as well (which at present they cannot despite the fact that I am pushing the route 192.168.30.0 255.255.255.0). The other site's administrator cannot add the extra route for my openvpn clients for a lot of reasons which I am not going to enter at this stage. Is there a possibility that I could NAT all of my openVPN road-warriors requests through a local LAN IP address (something like 10.100.100.250 which is not used by anything on my LAN). The problem is that I am a newbie with pfSense so as much step-by-step help as possible would be very much appreciated! Thank you. C.

    Read the article

  • Active Directory Domain Services - Network Name Cannot be Found

    - by Arief
    I have really weird problem that I could not explain. I am trying to redirect all users home folder to the new server. I have copied all the files including the permissions to the new server. All I need to do is to update the user profile for home folder by changing the server name. However, I got this message when I enter the new server name: My server that serving as AD can resolve the name by ping and nslookup of the server name. The only thing that I don't understand why the MMC cannot resolve the name. I did change with the IP Address and I still get the same error message. Thank you so much for your help. UPDATE: I know what seems to be a problem, but I don't know how to fix it. The new server that will serve all Home folder is actually sitting in the cloud with different IP Address as the Domain Controller. The Domain Controller is sitting locally in the office with 10.0.0.0/24 IP Addresses. The new server that is sitting in on Data Centre is on 172.10.10.10/24 IP Addresses. The static route has been set up on both end, and the DNS as well. I believe this is the issue. Does anyone how to overcome this situation? Thank you.

    Read the article

  • Bash Script - Traffic Shaping

    - by Craig-Aaron
    hey all, I was wondering if you could have a look at my script and help me add a few things to it, How do I get it to find how many active ethernet ports I have? and how do I filter more than 1 ethernet port How I get this to do a range of IP address? Once I have a few ethenet ports I need to add traffic control to each one #!/bin/bash # Name of the traffic control command. TC=/sbin/tc # The network interface we're planning on limiting bandwidth. IF=eth0 # Network card interface # Download limit (in mega bits) DNLD=10mbit # DOWNLOAD Limit # Upload limit (in mega bits) UPLD=1mbit # UPLOAD Limit # IP address range of the machine we are controlling IP=192.168.0.1 # Host IP # Filter options for limiting the intended interface. U32="$TC filter add dev $IF protocol ip parent 1:0 prio 1 u32" start() { # Hierarchical Token Bucket (HTB) to shape bandwidth $TC qdisc add dev $IF root handle 1: htb default 30 #Creates the root schedlar $TC class add dev $IF parent 1: classid 1:1 htb rate $DNLD #Creates a child schedlar to shape download $TC class add dev $IF parent 1: classid 1:2 htb rate $UPLD #Creates a child schedlar to shape upload $U32 match ip dst $IP/24 flowid 1:1 #Filter to match the interface, limit download speed $U32 match ip src $IP/24 flowid 1:2 #Filter to match the interface, limit upload speed } stop() { # Stop the bandwidth shaping. $TC qdisc del dev $IF root } restart() { # Self-explanatory. stop sleep 1 start } show() { # Display status of traffic control status. $TC -s qdisc ls dev $IF } case "$1" in start) echo -n "Starting bandwidth shaping: " start echo "done" ;; stop) echo -n "Stopping bandwidth shaping: " stop echo "done" ;; restart) echo -n "Restarting bandwidth shaping: " restart echo "done" ;; show) echo "Bandwidth shaping status for $IF:" show echo "" ;; *) pwd=$(pwd) echo "Usage: tc.bash {start|stop|restart|show}" ;; esac exit 0 thanks

    Read the article

  • New Computer freezing up at random

    - by Benjamin Frost
    Since I built my system about 4 weeks ago I'v been getting random freezes, Sometimes it can happen directly after startup and sometimes it wont freeze up for 3-4 days of 24/7 running. It seems to be happening under all stress loads but mainly when the CPU is under 10% load. It doesn't give me a BSOD or anything, it simply just freezes and repeats the last sound before the freeze until I shut it down by the power button. I'v re-seated everything in the system except the CPU, Cleaned the RAM sockets and gold fittings. None of the components have been clocked above their factory settings as of yet, don't want to overclock them until I sort out these freezes. Temps are all well under the rated max temps, the highest the temps have been are below CPU: Low load: 16-21°C Full Load (100%) 40-43°C *(From HWMonitor by CPUID) GPU 1: Low Load: 25-30°C Full Load (100%): 45-50°C GPU 2: Low Load: 23-27°C Full Load (100%): 45-50°C *(GPU Temps from Catalyst Control Center) General Case temps Rear: 18-20°C Mid: 20-21°C Front (HDD/SSD Bays): 14-19°C (Case temps may be a little off as it's from the Kaze master pro fan controller) I have Un-installed EVERY driver for Motherboard, GPU & Soundcard and Re-installed twice. Windows is all up to date. To date i'v tried the following Running Memtest for 24 hrs straight, No errors Running Memtest on each individual RAM modules, No errors Reseated everything except the CPU Cleaned DIMM Sockets and Gold inputs Tested the Graphics cards 1 at a time Re-arranged all the SATA devices to run on Chipset controlled ports Re-installing all drivers OS: Win7 Professional 64bit Motherboard: ASRock X79 Extreme9 CPU: i7 3930k 3.2GHz GPU: Sapphire 7950 OC Edition V2 (2 card Crossfire) RAM: G.Skill Ripjaws Z F3-17000CL11Q-16GBZL 16GB (4x4GB) DDR3 Boot Drive: OCZ Agility 4 128GB Data Drive 1: Western Digital Black 2TB Data Drive 2: Western Digital Black 2TB Data Drive 3: Western Digital Green 3TB Power Supply: Corsair AX1200 Gold

    Read the article

  • KVM Guest with NAT + Bridged networking

    - by Daniel
    I currently have a few KVM Guests on a dedicated server with bridged networking (this works) and i can successfully ping the outside ips i assign via ifconfig (in the guest). However, due to the fact i only have 5 public ipv4 ip addresses, i would like to port forward services like so: hostip:port - kvm_guest:port UPDATE I found out KVM comes with a "default" NAT interface, so added the virtual NIC to the Guest virsh configuration then configured it in the Guest, it has the ip address: 192.168.122.112 I can successfully ping 192.168.122.112 and access all ports on 192.168.122.112 from the KVM Host, so i tried to port forward like so: iptables -t nat -I PREROUTING -p tcp --dport 5222 -j DNAT --to-destination 192.168.122.112:2521 iptables -I FORWARD -m state -d 192.168.122.0/24 --state NEW,RELATED,ESTABLISHED -j ACCEPT telnet KVM_HOST_IP 5222 just hangs on "trying" telnet 192.168.122.112 2521 works [root@node1 ~]# tcpdump port 5222 tcpdump: WARNING: eth0: no IPv4 address assigned tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth0, link-type EN10MB (Ethernet), capture size 65535 bytes 23:43:47.216181 IP 1.152.245.247.51183 > null.xmpp-client: Flags [S], seq 1183303931, win 65535, options [mss 1400,nop,wscale 3,nop,nop,TS val 445777813 ecr 0,sackOK,eol], length 0 23:43:48.315747 IP 1.152.245.247.51183 > null.xmpp-client: Flags [S], seq 1183303931, win 65535, options [mss 1400,nop,wscale 3,nop,nop,TS val 445778912 ecr 0,sackOK,eol], length 0 23:43:49.415606 IP 1.152.245.247.51183 > null.xmpp-client: Flags [S], seq 1183303931, win 65535, options [mss 1400,nop,wscale 3,nop,nop,TS val 445780010 ecr 0,sackOK,eol], length 0 7 packets received by filter 0 packets dropped by kernel [root@node1 ~]# iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere 192.168.122.0/24 state NEW,RELATED,ESTABLISHED Chain OUTPUT (policy ACCEPT) target prot opt source destination All help is appreciated. Thanks.

    Read the article

  • ScreenOS MIP selection for outbound connections

    - by David Mackintosh
    Given a ScreenOS 6.3.0 firewall with this configuration: unset flow reverse-route clear-text set interface "ethernet0/0" zone "Trust" set interface ethernet0/0 ip 192.168.1.1/24 set interface ethernet0/2 ip 10.0.0.1/24 set interface ethernet0/2 mip 10.9.9.10 host 192.168.1.10 netmask 255.255.255.255 vr trust-vr set interface ethernet0/2 mip 10.8.8.10 host 192.168.1.10 netmask 255.255.255.255 vr trust-vr set route 0.0.0.0/0 interface ethernet0/2 gateway 10.0.0.254 ... (and assuming appropriate policies) is there a way to control which MIP the firewall selects for outbound connections initiated by 192.168.1.10? (presumably because I want the upstream 10.0.0.254 to do different things with the packet depending on what its source IP is). Update: OK, my scenario is this: I have two ISP uplinks, each giving me a different IP space. Each ISP will only route the IP space they have assigned me. So in order for the server to be reachable by both ISPs, I need two MIPs for the same server, one on each interface. Inbound traffic will work fine with the 'unset flow reverse-route clear-text' option in use. But for outbound (think an email server sending a message) I need a way to select an appropriate MIP depending on which outbound link I want the system to use, and I want this to be resiliant so that if the link the firewall prefers goes down overnight I don't have to manually flip something to keep the mail flowing. Basically I'm trying to avoid having to buy a link-balancer appliance (or two since I'll need a cluster). Is there a way to do this?

    Read the article

  • Using pre-made patch cables on a punch down block?

    - by Trevor Harrison
    I need to add a 24 port switch to my wiring closet. In the (distant) past, I usually just punched each port of the switch to a 110 block on the wall (using hand-made cables), and cross connect between that and the 110 block that has the runs to each workstation. To save time, I'm thinking of buying 12 pre-made drop cables, cutting them in half (so 24 single ended cables), and punching those to my 110 block. The things I'm worried about are wire type (ie. solid vs. strands) and color scheme. I really don't know if they use different wire types (still?), but I remember that being an issue at one point. Can anyone comment on this? (I definitely won't feel comfortable trying to punch stranded wiring on my 110 block) Also, picking up a random pre-built cable I had laying around, I noticed that the color scheme used didn't appear to be T568B, but T568A, which would clash with the rest of my wall. Anyone know of an online source that specifies these things? I've looked at www.cablesforless.com (which does have nicer prices) and www.cablestogo.com (which seem stupid expensive) so far. Cables For Less doesn't specify wiring scheme, Cables To Go does specify T568B. Both seem to specify stranded wires instead of solid.

    Read the article

  • NFSv4 "Too many levels of symbolic links" error

    - by user1434058
    Both machines are running Ubuntu 12.04 Remote NFSv4 Client $ ls /mnt/storage/aaaaaaa_aaa/bbbb/cccc_ccccc gives this error: ls: reading directory .: Too many levels of symbolic links How can I fix this? When error occurs ls start listing the files, however PHP brakes. On the NFSv4 Server In /etc/fstab: /mnt/storage /srv/storage none bind 0 0 In /etc/exports /srv 192.168.1.0/24(rw,async,insecure,no_subtree_check,crossmnt,fsid=0,no_root_squash) /srv/storage 192.168.1.0/24(rw,async,nohide,insecure,no_subtree_check,no_root_squash) ERROR root@ds:root@ds:/mnt/storage/foreign_dbs/imdb/imdb_htmls# ls -l | head ls: reading directory .: Too many levels of symbolic links total 10302840 -rw-r--r-- 1 root root 10484 Jul 5 13:56 0019038.gz -rw-r--r-- 1 root root 16264 Mar 30 00:31 0259701.gz -rw-r--r-- 1 root root 13784 Mar 30 14:20 1000000.gz -rw-r--r-- 1 root root 12741 Mar 30 13:04 1000003.gz -rw-r--r-- 1 root root 12794 Mar 30 12:40 1000004.gz -rw-r--r-- 1 root root 13123 Mar 30 12:07 1000005.gz -rw-r--r-- 1 root root 13183 Mar 30 12:04 1000006.gz -rw-r--r-- 1 root root 13443 Jul 4 01:16 1000007.gz -rw-r--r-- 1 root root 12968 Mar 30 11:05 1000008.gz I came across it in PHP. scandir would return 1612577.gz & 1612579.gz, but skips 1612578.gz and yet the file types and properties are identical on them and this only happens on the nfs client, works 100% on the server

    Read the article

  • netconfig won't change DNS on opensuse 12.2

    - by Krystian
    I'm trying to update my dns servers after openvpn connection, but netconfig won't do that for me. Here's how I'm trying to do it [manually now]: /sbin/netconfig modify -v -i tap0 -s openvpn <<-EOF INTERFACE='tap0' DNSSERVERS='10.10.0.1' EOF And here's the verbose output: debug: lockfile created (/var/run/netconfig.pid) for PID 5530 debug: lockfile created debug: write new STATE file /var/run/netconfig//tap0/netconfig0 debug: Module order: dns-resolver dns-bind dns-dnsmasq nis ntp-runtime debug: dns-resolver module called debug: Static Fallback debug: Use NetworkManager policy merged settings debug: exec get_dns_settings: /var/run/netconfig/NetworkManager.netconfig debug: get_dns_settings: service 'NetworkManager' => rank '1' debug: get_dns_settings: DNS_SEARCHLIST_1='mydomain.com' debug: get_dns_settings: DNS_SERVERS_1='192.168.0.1' debug: exit get_dns_settings: /var/run/netconfig/NetworkManager.netconfig debug: write_resolv_conf: ' mydomain.com ' ' 192.168.0.1 ' debug: No changes for /etc/resolv.conf debug: dns-bind Module called debug: dns-dnsmasq Module called debug: nis Module called debug: Static Fallback debug: Use NetworkManager policy merged settings debug: exec get_nis_settings: /var/run/netconfig/NetworkManager.netconfig debug: exit get_nis_settings: /var/run/netconfig/NetworkManager.netconfig debug: set_nisdomainname: eth0 24 debug: set_nisdomainname: => yes debug: set_nisdomainname: old[]=, new[24]= debug: format_yp_conf called with : debug: Using static fallback debug: format_static[0] called debug: No changes for /etc/yp.conf debug: nis domainname '' is up to date debug: ntp-runtime Module called debug: Static Fallback debug: Use NetworkManager policy merged settings debug: exec get_ntp_settings: /var/run/netconfig/NetworkManager.netconfig debug: get_ntp_settings: NTP_SERVER_LIST='' debug: exit get_ntp_settings: /var/run/netconfig/NetworkManager.netconfig I've been trying to find something relevant on the web, but failed to do so. I have no other clue on how to progress with this issue. Any thoughts?

    Read the article

  • Why would I be getting IXFR and AXFR transfer denied on my DNS server?

    - by danielj
    From everything I've researched and tried, it appears that my named.conf is configured correctly, including the allow-transfer section. Here is a sample of the errors. It is only happening with a couple of my secondary servers, but it is happening for every zone for those servers that are failing. One of the servers is attempting IXFR, the other AXFR. The result is the same: 18-Mar-2011 14:27:51.372 security: error: client 84.234.24.90#59208: zone transfer 'juansgaranton.com/IXFR/IN' denied 18-Mar-2011 14:32:18.015 security: error: client 174.37.196.55#50783: zone transfer 'cheshirecat.net/AXFR/IN' denied Here is the relevant part of named.conf. options { directory "/etc/bind"; pid-file "/var/run/named/named.pid"; files 4096; allow-transfer { 140.186.190.103; 84.234.24.90; 207.246.95.34; 203.20.52.5; 140.186.190.103; 127.0.0.1; 174.37.196.55; }; }; logging { channel "bind" { file "/var/log/bind.log" versions 3; print-time yes; print-severity yes; print-category yes; severity info; }; category lame-servers { null; }; category "default" { "bind"; }; };

    Read the article

  • how to grep ip from ifconfig output

    - by Registered User
    Following is my ifconfig output eth0 Link encap:Ethernet UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:28 Base address:0x2000 eth1 Link encap:Ethernet inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:36497 errors:0 dropped:0 overruns:0 frame:14515 TX packets:44884 errors:1352 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:20781745 (20.7 MB) TX bytes:17776225 (17.7 MB) Interrupt:17 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) virbr0 Link encap:Ethernet inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:24 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:4416 (4.4 KB) vmnet1 Link encap:Ethernet inet addr:192.168.185.1 Bcast:192.168.185.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:24 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) vmnet8 Link encap:Ethernet inet addr:192.168.207.1 Bcast:192.168.207.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:25 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) I want to do some thing grep that I see the IP corresponding to each LAN card? Is that possible? How can it be achieved?

    Read the article

  • is it worth to use load balancer on web server/website

    - by user427969
    I have a website and a while ago, the web server of the company hosting my website was down for about a day. I consulted the company for a solution on how i can stop this from happening in future and they suggested to have a second machine and which will be connected to my current website/web server by a "load balancer" (at an additional huge cost!!!). The second machine will be replicate of the first one and so if i goes down, the other will always be running. ---- Explanation ----- My hosting company suggested that it will be a good idea to have a second machine running at the same time and both the machines will be connected by a load balancer which reduces the rist of a downtime. The second machine will be a mirror of the first and any changes to first must be replicated in the second. I don't mind spending money if it really saves my website from going down. I want to know is it worth having this "load balancer" for my purpose? My website is a 24/7 service. I cannot afford an outage of 24 hours/1 hour. I don't mind using this "load balancer" as far as it is really worth. I am not sure if its just a marketing trick of my hosting company or really a "best" solution Thanks for help. Regards

    Read the article

  • Amazon EC2 Reserved Instances: "Heavy Utilization" clarification

    - by gravyface
    Should be another easy one here, but I need clarification on what they define as "heavy utilization" for Reserved Instance types. From their Website: Heavy Utilization RIs – Heavy Utilization RIs offer the most absolute savings of any Reserved Instance type. They’re most appropriate for steady-state workloads where you’re willing to commit to always running these instances in exchange for our lowest hourly usage fee. With this RI, you pay a little higher upfront payment than Medium Utilization RIs, a significantly lower hourly usage fee, and you’re charged that lower hourly rate for every hour in the Reserved Instance term you purchase. Using Heavy Utilization RIs, you can save up to 41% for a 1-year term and 58% for a 3-year term vs. running On-Demand Instances. If you’re trying to find a break-even utilization, you’re economically advantaged using Heavy Utilization RIs (vs. On-Demand Instances) if you plan to use your instance more than 43% of a 1-year term or 79% of a 3-year term. I'm assuming that, if I'm planning on running a 24/7 Web Server, then regardless of how many resources I consume (bandwidth, cpu cycles, memory), I would want to go with a Heavy Utilization Reserved Instance? This one Web Server in particular will likely barely budge the cpu, but it needs to be up and running 24/7. Not 100% on what they're defining as "heavy".

    Read the article

  • kickstart ks.cfg: Where should 'url' point?

    - by Stefan Lasiewski
    I have a kickstart file (ks.cfg) on a floppy (Old style). I am trying to install CentOS 5.4. The top of my ks.cfg says this: install # Install from local cdrom or over the network. #cdrom url --url http://kickstart.example.org/pub/centos/5.4/ On the Apache server side, this command is failing with these 404s: kickstart.example.org 192.168.16.180 - - [01/Jun/2010:17:24:30 -0700] "GET /pub/centos/5.4///disc1/.discinfo HTTP/1.1" 404 314 "-" "urlgrabber/3.1.0" kickstart.example.org 192.168.16.180 - - [01/Jun/2010:17:24:43 -0700] "GET /pub/centos/5.4/repodata/repomd.xml HTTP/1.1" 404 316 "-" "urlgrabber/3.1.0 yum/3.2.22" It seems that the value of my url doesn't match the directory structure on the server. I swear this worked a few months ago. Someone else maintains the Yum repository, and they say nothing has changed. What should the value of url URL be? Should this only include the OS (/pub/centos/5.4/), or should it include the architecture (/pub/centos/5.4/os/x86_64 )? I see that Kickstart is trying to grab a file called 'repomd.xml', but why is it looking in '/pub/centos/5.4/repodata/repomd.xml', when these files actually exist at '/pub/centos/5.4/os/x86_64/repodata/repomd.xml' and other locations at '/pub/centos/5.4/*/$ARCH/repodata/repomd.xml'? I don't see this documented or explained well in the [RedHat 5 Installation Guide1]

    Read the article

< Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >