Search Results

Search found 7154 results on 287 pages for 'networking'.

Page 136/287 | < Previous Page | 132 133 134 135 136 137 138 139 140 141 142 143  | Next Page >

• Why does my DD-WRT not accept SSH connections from my laptop?

  - by Vlad Seghete

  So, here is my system: I have a 2Wire AT&T modem/router which I use for wireless and a Buffalo router flashed with DD-WRT which is physically attached to the 2Wire and set in the DMZ. I set everything up on the DD-WRT to be able to connect to it using ssh and also so that it forwards ssh requests on a different port to one of the servers behind it. Now, when I am physically connected to the DD-WRT all this works great and as I would want it to. I ssh into the two different ports using the WAN IP of my network, and I get where I expect to land. If, however, I am connected using wi-fi to the 2Wire, the same commands do not work. I do not get an error, simply a timeout. I have trouble understanding this, since the DD-WRT is set in the DMZ and everything should pass to it. To further complicate the problem, I tried connecting to the same IP using my phone (wireless disabled, so really from the WAN) and surprise, it works! If I go back on the local network by enabling the wifi, the ssh connection times out. To make this even stranger, my WAN IP address always responds to pings (meaning in all the above situations). What could be going on here? I know what I should do, completely disable the 2wire as a router and use it strictly as a modem and them use all the routing capabilities of the dd-wrt. It's what I will probably end up doing anyway, but my question remains, because I really want to know what is happening here.

  Read the article

• Why isn't 'ether proto \ip host host' a legal tcpdump expression?

  - by Ezequiel Garzon

  In its description of valid tcpdump expressions, the pcap-filter man pages state: The filter expression consists of one or more primitives. Primitives usually consist of an id (name or number) preceded by one or more qualifiers. In turn, these qualifiers are type, dir and proto. So far so good, but further down we find this: ip host host which is equivalent to: ether proto \ip and host host In the first case, ip and host are, respectively, proto and type. What pattern does ether proto \ip follow? Isn't that, as a whole, a proto qualifier? If so, why isn't (a properly escaped) 'ether proto \ip host host' legal (no and)?

  Read the article

• syslog ip ranges to specific files using `rsyslog`

  - by Mike Pennington

  I have many Cisco / JunOS routers and switches that send logs to my Debian server, which uses rsyslogd. How can I configure rsyslogd to send these router / switch logs to a specific file, based on their source IP address? I do not want to pollute general system logs with these entries. For instance: all routers in Chicago (source ip block: 172.17.25.0/24) to only log to /var/log/net/chicago. all routers in Dallas (source ip block 172.17.27.0/24) to only log to /var/log/net/dallas. Finally, these logs should be rotated daily for up to 30 days and compressed. NOTE: I am answering my own question

  Read the article

• How to spy on an XP machine

  - by Phenom

  I have a Windows 7 machine and XP machine on the same router. If someone is using the XP machine, how can I see what they're doing from my Windows 7 machine?

  Read the article

• How can I print from my lion mac mini to my windows XP, with simple file sharing?

  - by Jules

  I have quite a complicated setup, perhaps. And a lot of history on this issue, I'm hoping that I don't have to buy a new printer. I've got a HP Wireless USB Print Server, which requires client software, I can't just use it as an IP Printer. The HP software is pretty poor on the mac and is no longer supported and often locks up the printer server and takes some considerable effort to actually print something. Let alone if a windows machine attaches to it first. My printer is an Epson Stylus R285. However, the windows client software is fine and we can print from windows 7 / XP without problem. We have simple file sharing setup as this is the only way I could get windows XP to talk to windows 7. However, I can't seem to get my mac mini to connect as anything other than a guest to my xp machine, to connect to the shared printer. I'm not considering some kind of internet printing as this would seems the simplest solution. But I'm not sure what will work with my setup ?

  Read the article

• Severe latency only on one machine and only when accessing intranet site

  - by Joe M.

  I have one desktop machine that is having consistently high latency only when trying to load a page from an intranet site. Using the Chrome Developer Tools, the site shows a "Waiting" time of 4-5 seconds each page load. Other machines have <50ms, and the problem machine loads regular internet sites with <1s latency, so the problem is only on one machine and only when accessing the intranet site. This is a small business and all the hosts are on 192.168.0.1/24 I would have suspected a connection issue with the problem machine but normal internet sites are not having latency. Then I would have looked at connection issues with the intranet web server but other machines are not having latency to it. What else can I look at to troubleshoot this?

  Read the article

• How to set up multiple SSIDs with bandwidth limiting on a single wireless router?

  - by Rahul Narain

  I have an Asus WL-520GU wireless router connected to a cable modem that I use for wireless internet access in my apartment. I would like to set it up so that it provides two SSIDs: one secured and password-protected for my regular use, and a "guest" SSID that's unsecured but throttled to, say, 10% of the available bandwidth. What is the most straightforward way to do this? I've been looking into DD-WRT and Tomato, both of which support my router. DD-WRT supports setting up multiple SSIDs using the GUI, but I don't know if it's possible to limit the bandwidth of each SSID independently; point #12 in this FAQ thread says it's not possible to limit by day or by MAC address, which is discouraging but not conclusive. Tomato allows bandwidth limits in its QoS settings, going by the screenshot here, but multiple SSID support is still experimental and it doesn't look like it will work with the encryption settings or bandwidth limits in the GUI. I'd like to know a good way to do this which gives me the fewest opportunities for screwing up. I'm no stranger to the command line, if that turns out to be what's necessary, but if so, please explain what the commands are doing because I don't have a good mental model of what needs to happen to set this up.

  Read the article

• Which program is using my network bandwidth on Mac OS X?

  - by leolobato

  Hey guys, I use iStats Menu to monitor my network usage on OSX. Is there a quick way to know which processes are using the network at any given moment? Sometimes my downstream bandwidth will be at close to 100% and I'm not downloading anything... I assume it's OSX auto-update stuff, but I just want to be sure.

  Read the article

• Ping: Destination Host Unreachable, from the destination host itself

  - by phunehehe

  I have a server that responds in a weird way to ping: $ ping hostname.com PING hostname.com (<IP address>) 56(84) bytes of data. From hostname.com (<IP address>) icmp_seq=1 Destination Host Unreachable From hostname.com (<IP address>) icmp_seq=2 Destination Host Unreachable From hostname.com (<IP address>) icmp_seq=3 Destination Host Unreachable From hostname.com (<IP address>) icmp_seq=4 Destination Host Unreachable I'm confused, as the messages come from the server that I want to ping, and at the same time it's saying Destination Host (itself) Unreachable. Pinging by IP address yields the same result. The server is online and operating normally. What could be the cause?

  Read the article

• My Macbook Pro wifi intermittently won't turn on sometimes after sleep, does anyone know how to solve this?

  - by Simon

  Hello, My current-generation MacBook Pro 15" (10.6.5) intermittently has problems turning the wifi (airport) on. The usual symptom happens when I: Sleep the machine Open from sleep Wifi is off (the airport signal is blank) I click on airport icon-Turn Airport On, but nothing happens. I googled around a bit and found one recommended solution where I delete the "automatic" location and create a new one and enable the wifi, or I delete the "AirPort" from the location and add it back, but neither of these resolve the problem. I also called AppleCare and they had me delete /Library/SystemConfiguration and restart, but that hasn't solved the problem. I have to reboot, which is very painful. Does anyone have any idea of how to solve this?

  Read the article

• Configure Wireless Network Card

  - by Skizz

  I recently upgraded the wireless network card in my Ubuntu PC from an 802.11g to an 802.11n. Now, it can't see my router. It doesn't appear in the list of networks that is displayed when you click on the NetworkManager icon in Gnome. Other networks are listed and I have connected to them (no password required!). I'm using the Windows driver through ndiswrapper and it can see the card. I tested the card in a Windows PC and everything worked. The router's log doesn't show any messages coming from the wireless card. What have I done wrong? If you need any more information, just leave a comment and I'll get add it to the question.

  Read the article

• Tool to indicate type of network connection

  - by ggonsalv

  I know of whoami.exe. Is there a version called whereami.exe The output should be able to tell me if I am on a LAN, wireless or VPN. the machines would be running Windows Xp or better.

  Read the article

• Cannot connect to WEBrick on home network

  - by Chris Stewart

  I'm an Android developer and often my applications require server-side code. I typically use Ruby on Rails for the web app, and during development will run the server on my local machine (Mac OS X) with WEBrick. In the morning when I get to the office, I'll run ifconfig in the console to see what IP my laptop has been given that day. I'll use that IP in my Android app when making requests to the web app in question. This all works fine, when I'm in my office. When I get home, I attempt to do the same thing, find my laptop's IP via ifconfig, set it in my app's config file, but the destination can never be found. To exclude my app from the set of hurdles, I attempt to visit the web server IP (e.g., http://192.168.1.4:3000) from my phone's browser, and it cannot connect. If I try from my laptop, which is running the web server, it works fine. If I try from another machine, on the same network, it also is unable to connect. Given this, I think I've narrowed it down to some kind of configuration in my home network, but I frankly have no idea what the cause could be. I don't have anything special at home, your basic Verizon FiOS router/modem with everything connected via Wi-Fi (Wi-Fi for both phone and laptop at work as well, fyi). I've tried disabling the firewall on my Verizon router, enabling port forwarding, and just about everything else I could do for port 3000, and nothing has changed. Dear Server Fault geniuses, please help a poor developer out. :) Edit: Some follow up items to add. My Mac's firewall is not active, and all incoming requests are allowed. I've also verified on my phone and laptop, that they're on the same network (192.168.1.4 Mac, 192.168.1.9 Phone). I have no idea why this isn't working. Edit 2: I went into System Preferences, enabled Web Sharing, and tried to view the website from my phone and it didn't connect. So it's not WEBrick or related to Rails. The firewall on my machine is off and the firewall on my router is off. Edit 3: Some progress. I set up port forwarding for port 3000 to my laptop, found the external IP, and used that and it connected fine. So, there's definitely something not quite set up correctly on my internal network.

  Read the article

• Only 192.168.0.3 can request most files, but anyone can request /public/file.html

  - by mattalexx

  I have the following virtual host on my development server: <VirtualHost *:80> ServerName example.com DocumentRoot /srv/web/example.com/pub <Directory /srv/web/example.com/pub> Order Deny,Allow Deny from all Allow from 192.168.0.3 </Directory> </VirtualHost> The Allow from 192.168.0.3 part is to only allow requests from my workstation machine. I want to tweak this to allow anyone to request a certain URL: http://example.com/public/file.html How do I change this to allow /public/file.html requests to get through from anyone? Note: /public/file.html doesn't actually exist as a file on the server. I redirect all incoming requests through a single index file using mod_rewrite.

  Read the article

• How much packet loss is normal?

  - by Fabian

  I started monitoring our network using SmokePing. Users occasionally complain about bad network connections, but the problems went away after some minutes usually. I now wanted to get some more quantitative information about those problems. SmokePing regularly pings servers inside our network, in a connected network and outside hosts. I only have a limited amount of control over our internal network and none at all for the connection to the outside and to the second network. I now see quite often (2-4 times a day) that packets to the second network and the outside are dropped. Most of the times it is 1-2 packets out of 20, sometimes more. Inside our internal network no packets are dropped. Is this an expected amount of packet loss, or does it indicate that something is wrong? I'm mainly wondering if I should bother the university IT department about it, or if I should just accept it as it is.

  Read the article

• Keepalived for more than 20 virtual addresses

  - by cvaldemar

  I have set up keepalived on two Debian machines for high availability, but I've run into the maximum number of virtual IP's I can assign to my vrrp_instance. How would I go about configuring and failing over 20+ virtual IP's? This is the, very simple, setup: LB01: 10.200.85.1 LB02: 10.200.85.2 Virtual IPs: 10.200.85.100 - 10.200.85.200 Each machine is also running Apache (later Nginx) binding on the virtual IPs for SSL client certificate termination and proxying to backend webservers. The reason I need so many VIP's is the inability to use VirtualHost on HTTPS. This is my keepalived.conf: vrrp_script chk_apache2 { script "killall -0 apache2" interval 2 weight 2 } vrrp_instance VI_1 { interface eth0 state MASTER virtual_router_id 51 priority 101 virtual_ipaddress { 10.200.85.100 . . all the way to . 10.200.85.200 } An identical configuration is on the BACKUP machine, and it's working fine, but only up to the 20th IP. I have found a HOWTO discussing this problem. Basically, they suggest having just one VIP and routing all traffic "via" this one IP, and "all will be well". Is this a good approach? I'm running pfSense firewalls in front of the machines. Quote from the above link: ip route add $VNET/N via $VIP or route add $VNET netmask w.x.y.z gw $VIP Thanks in advance. EDIT: @David Schwartz said it would make sense to add a route, so I tried adding a static route to the pfSense firewall, but that didn't work as I expected it would. pfSense route: Interface: LAN Destination network: 10.200.85.200/32 (virtual IP) Gateway: 10.200.85.100 (floating virtual IP) Description: Route to VIP .100 I also made sure I had packet forwarding enabled on my hosts: $ cat /etc/sysctl.conf net.ipv4.ip_forward=1 net.ipv4.ip_nonlocal_bind=1 Am I doing this wrong? I also removed all VIPs from the keepalived.conf so it only fails over 10.200.85.100.

  Read the article

• Is there no such thing as a Gigabit switch?

  - by Torben Gundtofte-Bruun

  According to the manufacturer specification, even my rather plain desktop computer has "Gigabit Ethernet". So when I want to copy large files over the LAN (not Internet) it would make sense to have a gigabit switch. I'm searching eBay for a gigabit switch for a planned home network upgrade. The products I find are all labeled "gigabit" but they all have 24 x 10/100Mbit autosensing ports and sometimes 2 x 10/100/1000Mbit autosensing ports. It was my understanding that 10/100 is ancient and that modern computers have network interfaces that work with 1000Mbit, so it would make sense to get a switch that has 24 x 1000Mbit ports. Did I misunderstand, or are sellers (deliberately?) mislabeling older hardware? (Let's not dive into wired vs. wireless networks and how "N" wireless is fast. You'd be right, but not answering the question.)

  Read the article

• Can not access network computers anymore

  - by Johny Skovdal

  Last Thursday (03/05/12) I got a new computer to be able to work from home. I plugged it, by cable, into the company network and installed most of the software needed for me to do so, by accessing a share on my stationary computer at work. I had no issues here what so ever, and everything just worked. Yesterday evening I tried accessing the company network trough Windows VPN, and while I was able to connect to the network, I was unable to connect to any computers on the network. I did, however, get an error when connecting, but I can't seem to get the error again, to get the details of the error message. Today I am sitting on the company network again, and now I can not access anything on the network like I could last Thursday, though I can ping all the computers I am attempting to access. Here is a list of details that might help in troubleshooting this issue (updated): List of observations / actions My computer is identical to another computer that has no issues. It is not on the domain but rather on the default workgroup, but this was not an issue last Thursday, so I am assuming it still is not. I am able to access my e-mail on the exchange server. I can connect to our TFS server from Visual Studio but not from Explorer. I can also connect to Database Servers and Remote Desktop. I can see several computers when browsing network computers, but I am unable to connect to any of them. When trying to connect to a computer I am consistently met with the error code "0x80070035" (network path not found). I also get the 0x80070035 error when double clicking the target computer from the Network UI. I am not met with a login dialog when trying to access a computer, as I should, since I am not on the domain. (I did login to both Exchange, Remote Desktop and TFS though) Between Thursday where it worked and Sunday evening where it did not, I have installed quite a few security updates, plus various tools etc. that I need for programming. I have tried accessing by computer name and ip and neither of them work. I can ping by computer name. I have deleted all (1 entry) stored network credentials. I am able to access my computer from the target computer. Client and Server can see each other on the network = Network Discovery is enabled. I am using the network profile "Work". When accessing the network through VPN, I am unable to get anything to work using computernames, but all of the above applies when using IP adresses instead of computername. I run Windows 7 Home Premium on my computer. Using powershell attempting to access a share I get the following error (ComputerName and ShareName being correct values of course): PS C:\Users\MyUser> cd \\ComputerName\ShareName Set-Location : Cannot find path '\\ComputerName\ShareName' because it does not exist. At line:1 char:3 + cd <<<< \\ComputerName\ShareName + CategoryInfo : ObjectNotFound: (\\ComputerName\ShareName:String) [Set-Location], ItemNotFoundException + FullyQualifiedErrorId : PathNotFound,Microsoft.PowerShell.Commands.SetLocationCommand However, ping'ing the same machine (ping ComputerName) from powershell I get response immediately. (As mentioned in the list of observations/actions, I tried the above with the IP address again on VPN, to get the same result) Conclusion So to sum up, pretty much the only thing I can not do, is access the other computers through browsing (explorer.exe, powershell, map networkdrive, etc.), which means that I am pretty much down to, that it is unable to resolve the path somehow, when trying to connect to other computers trough browsing, though the path gets resolved perfectly using all kinds of other services. Any recommendations as to what I can try next to resolve the issue? :)

  Read the article

• Time-Machine backup over SSH tunnel to NFS mount

  - by BTZ

  I've recently started using a new NAS which runs CentOS 6.2. One of the purposes of the NAS would be to serve as a backup target. Whilst I have been using Apple's Time-Machine for a while and I am very satisfied with it, I'd like to continue using it. Backing up directly to an address in my network is no hassle; all works fine. For security reasons I'd like all my traffic to go through an ssh tunnel to the NAS. This way I can avoid needing to get a VPNserver (for personal reasons). As of NFSv4 the NFS deamon is bound to port 2049, which makes it easy for me to direct all traffic through a ssh tunnel. Tunnel: ssh -f admin@ms -L 2000:localhost:2049 -N Mount: mount -t nfs -o nfsvers=4,rw,proto=tcp,sync,intr,hard,timeo=600,retrans=10,wsize=32768,rsize=32768,port=2000 localhost:/mac_backup /Volumes/backup This works fine for Finder/terminal and throughput is almost equal to direct traffic. (CPU of the NAS does ride high when I reach max bandwidth though) Now the problem: With Time-Machine I can't use the NFS mount point mounted on localhost. TM seems to try to connect to it and then give me a "OSStatus error 65". I also tried using NFSv3 (I correctly forwarded all ports) with no luck. Can anyone shed a light on this and/or give a solution?

  Read the article

• Wireless router not connection -> AP Not associated

  - by candido

  I can not connect to internet by wireless router after some months with ubuntu 10.04. I can connect with the same portable but with win OS. My SO is ubuntu 10.04 linux 2.6.32-41 arch SMP i686. The internet wireless network controller is Atheros AR9285 chipset (pci express) Kernel module ath9k I have tried a command line connection: $ sudo /etc/init.d/network-manager stop #stop gui network manager $ iwconfig wlan0 essid WLAN_3C key s:C001D20550B3C $ ifconfig Access Point: NOT-ASSOCIATED $dmesg ... AP 00:1a:2b:08:60:49 associated Is the SO has connected to router for booting long ( associated message), after boot and login why the connection to router is not possible by network-manager or command line (NOT associated message)? Thanks in advance

  Read the article

• why udp client work when wirshark capture?

  - by herzl shemuelian

  I have two machine A,B windows 7 os .I connect them end to end and try run a performance test by using tcpreplay. step 1) I check conectivity between to point by netcat In A i run nc -lvup 5432 when I run on B nc -u 1.2.3.4 5432 I can send data from B to A step 2) when in I run tcpreplay in B tcpreplay -i %0 myudp.pcap in A I don't recevice any data . when I open wireshark in A then my nc can read data why? I check dst mac and dst ip in pcap file they are correct. is importan udp src mac or src ip for udp how that I open udp server ?

  Read the article

• Router loses connection to internet randomly

  - by tvanover

  I have a Belkin wireless G plus Mimo router and it randomly loses the connection to the internet. It seems to happen for a second or two, not enough to impact day to day browsing. But enough to disconnect games, or stall videos I am watching. It happens whether I am plugged into the router or connecting via wifi. I am unsure if it is my router or Comcast that is causing this issue. If I connect a computer directly to the modem the problem never occurs, so that tells me it is probably the router. But I also had a Netgear wireless router WGR614, and it had the same problem. I don't know where to start looking for the source of the problem. What logs should I be combing through? All my machines are win 7 of varying versions.

  Read the article

• When browsing a specific network share remotely, Windows Explorer continuously jumps back to the parent folder

  - by Evil Pigeon

  I am accessing a specific network path on another domain. It looks something like this: \\CoputerName.OtherDomain.in\c$\Inetpub\Testing\Website\ In under 30 seconds, I am automatically jumped back to \\CoputerName.OtherDomain.in\c$\Inetpub\Testing\ In less time it then jumps back to \\CoputerName.OtherDomain.in\c$\Inetpub\ Then it jumps back to c$ for its final resting place. \\CoputerName.OtherDomain.in\c$\ At first I thought this had to with a faulty keyboard, but this behaviour also occurs when the window does not have focus. It's as if windows thinks that the folder no longer exists (as in someone else has deleted or moved it). This behaviour is not specific to my PC either, it occurs from other machines in the office. Edit: It looks like this issue only occurs from other Windows 7 machines. There are no issues accessing the path from XP.

  Read the article

• How do I access my samba drive through several layers of network topology?

  - by stephenmm

  I have a new windows 7 Home Premium machine that is in a different room than my main computer area. As such I have to use a bridge and another router. Everything is working wonderfully except I cannot access the SAMBA drive with the new machine. I know that SAMBA is accessible as an older WinXP machine can access it. A picture of my network would probably be helpfull: To ISP | | +---------------------------+ | WAN | | Cable Modem | | (2WIRE678) | | | | | +---------------------------+ | +---------------------------+ | | (|) (|) +-----------+ | Belkin Router | | | | Wireless | | (F5D) |--+ +--| WinXP | | | |SAMBA USER | | | +-----------+ +---------------------------+ | | | | +------------+ | | Ubuntu | | | Apache + | | |SAMBA Server| | +------------+ | | +---------------------------+ | | | Netgear Bridge | | (XET1001) | | | +---------------------------+ # # +---------------------------+ | | | Netgear Bridge | | (XET1001) | | | +---------------------------+ | +---------------------------+ | | | D-Link Router | | (DI-524) | | | | | +---------------------------+ | | | | +-----------+ | | | Win7 | |SAMBA USER?| +-----------+ More interesting data points: 1. I can ping the SAMBA server from the Win7 machine locally (Ie. 192.168.2.2) 2. I can access the webserver from the Win7 machine locally (Ie. 192.168.2.2) 3. I followed the advice to get Win7 and SAMBA to play nice: http://www.tannerwilliamson.com/2009/09/windows-7-seven-network-file-sharing-fix-samba-smb/ Sorry for being so long winded but it is kind of complex and I am really at a loss as to how to fix it. If any of you have some suggestions I would love to hear it!

  Read the article

• Latency in TCP/IP-over-Ethernet networks

  - by aix

  What resources (books, Web pages etc) exist out there that: explain the causes of latency in TCP/IP-over-Ethernet networks; mention tools for looking out for things that cause latency (e.g. certain entries in netstat -s); suggest ways to tweak the Linux TCP stack to reduce TCP latency (Nagle, socket buffers etc). The closest I am aware of is this document, but it's rather brief. Alternatively, you're welcome to answer the above questions directly.

  Read the article

< Previous Page | 132 133 134 135 136 137 138 139 140 141 142 143  | Next Page >