Search Results

Search found 33477 results on 1340 pages for 'static vs non static'.

Page 136/1340 | < Previous Page | 132 133 134 135 136 137 138 139 140 141 142 143  | Next Page >

  • UPS vs Solar Power in case of power failure for a server [on hold]

    - by Zen 8000k
    I am looking for a low power, low end pc able to run 24/7 without overheating and a way to support it in case of power failure. Power failures can be up to 72 hours. The pc dosen't need a monitor or keyboard. A modem must also be protected in case of power failure. When i say low end, i don't mean crap. The cpu needs to be x86 and have at least 1k cpu in this chart: http://www.cpubenchmark.net/index.php What's the best way to do this? EDIT: more info. I need to run a home server. The server will perform light tasks mainly. A x86 cpu sadly is the only route for my use. I want to be able to run the server and the router/modem in case of power failure. Now, regarding how long the power will fail: 1) 1 hours is OK for most situations. (say 90%) 2) 3 hours is OK (say 98%) 3) 6 hours is more thank OK. (say 99.5%) 4) On extreme cases the power might fail days. I believe this is very unlikely to happen. More is great but, really, how ofter power will fail more than 3 hours? I believe once every year at best. Well, that's too rare to care about. Given the above, I am looking for a cost effective way to archive 1-3 hour power or 6 hour if possible. Solutions: You guys give me great ideas. 1) Power generator: no good as power will fail for 10 seconds before returning. Also I read online, "clean" power generators cost 1.5k+, so it's out of budged. Non clean generator might damage electronics, right? 2) Solar power: i don't know for sure about this. Sounds like a great idea, too good to be true, honestly. For only 200$ i get 100+w? What are the drawbacks here? 3) UPS: This seems to be the best. The only problem is the cost. Cost < 200$ = great 400$ = budged limit

    Read the article

  • Samsung i780 networking problem

    - by Infinity
    Hello guys! Maybe this is not the right place to ask this, but I give a try for it. Please don't rate it down, just ignore it if you don't like. So I have a Samsung i780 mobile phone and I would like to use the internet through my wireless router. I have connected to it. I got an IP address. My laptop is also connected to the same wireless network and I can ping the mobile phone and I get answer. When I open the internet explorer and enter an address it says that it cannot connect to the internet. I have googled very much, but can't find the problem. What do you think, what is the solution?

    Read the article

  • Website deployment - managing user-uploaded content?

    - by Legion
    I'm a programmer by trade, "server administrator" by company necessity. We're looking at dumping the old painful "update site by FTP upload" style of deployment. Having the webserver check out the latest code base from version control into a folder and having a "current" symlink point to the latest checkout (allowing for easily stepping back to an older version by changing the symlink) seems to be the way we want to go. But I have a question: what's a good practice for dealing with user-uploaded content? This stuff isn't in version control. I have a couple of ideas for dealing with this, but what is the smart, accepted practice?

    Read the article

  • Tunneling a public IP to a remote machine

    - by Jim Paris
    I have a Linux server A with a block of 5 public IP addresses, 8.8.8.122/29. Currently, 8.8.8.122 is assigned to eth0, and 8.8.8.123 is assigned to eth0:1. I have another Linux machine B in a remote location, behind NAT. I would like to set up an tunnel between the two so that B can use the IP address 8.8.8.123 as its primary IP address. OpenVPN is probably the answer, but I can't quite figure out how to set things up (topology subnet or topology p2p might be appropriate. Or should I be using Ethernet bridging?). Security and encryption is not a big concern at this point, so GRE would be fine too -- machine B will be coming from a known IP address and can be authenticated based on that. How can I do this? Can anyone suggest an OpenVPN config, or some other approach, that could work in this situation? Ideally, it would also be able to handle multiple clients (e.g. share all four of spare IPs with other machines), without letting those clients use IPs to which they are not entitled.

    Read the article

  • SQL Server 2008 R2 Express permet de gérer 10 Go de données et non plus 4, comme dans les précédente

    Mise à jour du 27/04/10 SQL Server 2008 R2 Express permet de gérer 10Go de données Et non plus 4Go, comme dans les précédentes versions gratuites Encore une nouvelle sur la version 2008 R2 de SQL Server ! Celle-ci concerne l'édition Express : autrement dit la version gratuite. Nouveauté principale de l'édition Express, elle permet à présent de gérer 10Go de données et non plus 4Go pour les précédentes versions. Plus d'informations sur SQL Server 2008 R2 Express et le lien vers le téléchargement

    Read the article

  • How to make sure clients update their browser cache when my website is updated?

    - by user64204
    I am using the HTTP 1.1 Cache-Control header to implement client-side caching. Since I update my website only once a month I would like the CSS and JS files to be cached for 30 days with Cache-Control: max-age=2592000. The problem is that the 30-day period defined by Cache-Control doesn't coincide with the website update cycle, it starts from the moment the users visit the site and ends 30 days later, which means an update could occur in the meantime and users would be running with outdated content for a while, which could break the rendering of the website if for instance the HTML and CSS no longer match. How can I perform client-side caching of content for periods of several days but somehow get users to refresh their CSS/JS files after the website has been updated? One solution I could think of is that if website updates can be schedule, the max-age returned by the server could be decreased every day accordingly so that no matter when people visit the website, the end of caching period would coincide with the update of the website, but changing the server configuration every day goes against one of my sysadmin principles (once it's running, don't touch it).

    Read the article

  • Could a singleton type replace static methods and classes?

    - by MKO
    In C# Static methods has long served a purpose allowing us to call them without instantiating classes. Only in later year have we became more aware of the problems of using static methods and classes. They can’t use interfaces They can’t use inheritance They are hard to test because you can’t make mocks and stubs Is there a better way ? Obviously we need to be able to access library methods without instantiated classes all the time otherwise our code would become pretty cluttered One possibly solution is to use a new keyword for an old concept: the singleton. Singleton’s are global instances of a class, since they are instances we can use them as we would normal classes. In order to make their use nice and practical we'd need some syntactic sugar however Say that the Math class would be of type singleton instead of an actual class. The actual class containing all the default methods for the Math singleton is DefaultMath, which implements the interface IMath. The singleton would be declared as singleton Math : IMath { public Math { this = new DefaultMath(); } } If we wanted to substitute our own class for all math operations we could make a new class MyMath that inherits DefaultMath, or we could just inherit from the interface IMath and create a whole new Class. To make our class the active Math class, you'd do a simple assignment Math = new MyMath(); and voilá! the next time we call Math.Floor it will call your method. Note that for a normal singleton we'd have to write something like Math.Instance.Floor but the compiler eliminates the need for the Instance property Another idea would be to be able to define a singletons as Lazy so they get instantiated only when they're first called, like lazy singleton Math : IMath What do you think, would it have been a better solution that static methods and classes? Is there any problems with this approach?

    Read the article

  • Microsoft souhaiterait vendre 100 millions de Windows Phone en 2012, les raisons de la non-prise en charge du dual-core par l'OS divulguées

    Microsoft a pour objectif de vendre 100 millions de Windows Phone en 2012 Les raisons de la non-prise en charge des processeurs dual-core par l'OS divulguées Microsoft aurait pour objectif interne de commercialiser plus de 100 millions de terminaux Windows Phone en 2012 d'après WMPowerUser, d'une source non divulguée. L'éditeur pourrait atteindre cet objectif ambitieux, si le constructeur Nokia amplifie sa production de terminaux Windows Phone à travers le monde avec des modèles différents. Selon WMPowerUser, les opérateurs s'attendraient à voir Windows Phone prendre 30% de parts de marché de smartphones en 2012. Une estimation qui rejoint celle

    Read the article

  • Problem with GCC calling static templates functions in templated parent class.

    - by Adisak
    I have some code that compiles and runs on MSVC++ but will not compile on GCC. I have made a test snippet that follows. My goal was to move the static method from BFSMask to BFSMaskSized. Can someone explain what is going on with the errors (esp. the weird 'operator<' error)? Thank you. In the case of both #defines are 0, then the code compiles on GCC. #define DOESNT_COMPILE_WITH_GCC 0 #define FUNCTION_IN_PARENT 0 I get errors if I change either #define to 1. Here are the errors I see. #define DOESNT_COMPILE_WITH_GCC 0 #define FUNCTION_IN_PARENT 1 Test.cpp: In static member function 'static typename Snapper::BFSMask<T>::T_Parent::T_SINT Snapper::BFSMask<T>::Create_NEZ(TCMP)': Test.cpp(492): error: 'CreateMaskFromHighBitSized' was not declared in this scope #define DOESNT_COMPILE_WITH_GCC 1 #define FUNCTION_IN_PARENT 0 Test.cpp: In static member function 'static typename Snapper::BFSMask<T>::T_Parent::T_SINT Snapper::BFSMask<T>::Create_NEZ(TCMP) [with TCMP = int, T = int]': Test.cpp(500): instantiated from 'TVAL Snapper::BFWrappedInc(TVAL, TVAL, TVAL) [with TVAL = int]' Test.cpp(508): instantiated from here Test.cpp(490): error: invalid operands of types '<unresolved overloaded function type>' and 'unsigned int' to binary 'operator<' #define DOESNT_COMPILE_WITH_GCC 1 #define FUNCTION_IN_PARENT 1 Test.cpp: In static member function 'static typename Snapper::BFSMask<T>::T_Parent::T_SINT Snapper::BFSMask<T>::Create_NEZ(TCMP) [with TCMP = int, T = int]': Test.cpp(500): instantiated from 'TVAL Snapper::BFWrappedInc(TVAL, TVAL, TVAL) [with TVAL = int]' Test.cpp(508): instantiated from here Test.cpp(490): error: invalid operands of types '<unresolved overloaded function type>' and 'unsigned int' to binary 'operator<' Here is the code namespace Snapper { #define DOESNT_COMPILE_WITH_GCC 0 #define FUNCTION_IN_PARENT 0 // MASK TYPES // NEZ - Not Equal to Zero #define BFSMASK_NEZ(A) ( ( A ) | ( 0 - A ) ) #define BFSELECT_MASK(MASK,VTRUE,VFALSE) ( ((MASK)&(VTRUE)) | ((~(MASK))&(VFALSE)) ) template<typename TVAL> TVAL BFSelect_MASK(TVAL MASK,TVAL VTRUE,TVAL VFALSE) { return(BFSELECT_MASK(MASK,VTRUE,VFALSE)); } //----------------------------------------------------------------------------- // Branch Free Helpers template<int BYTESIZE> struct BFSMaskBase {}; template<> struct BFSMaskBase<2> { typedef UINT16 T_UINT; typedef SINT16 T_SINT; }; template<> struct BFSMaskBase<4> { typedef UINT32 T_UINT; typedef SINT32 T_SINT; }; template<int BYTESIZE> struct BFSMaskSized : public BFSMaskBase<BYTESIZE> { static const int SizeBytes = BYTESIZE; static const int SizeBits = SizeBytes*8; static const int MaskShift = SizeBits-1; typedef typename BFSMaskBase<BYTESIZE>::T_UINT T_UINT; typedef typename BFSMaskBase<BYTESIZE>::T_SINT T_SINT; #if FUNCTION_IN_PARENT template<int N> static T_SINT CreateMaskFromHighBitSized(typename BFSMaskBase<N>::T_SINT inmask); #endif }; template<typename T> struct BFSMask : public BFSMaskSized<sizeof(T)> { // BFSMask = -1 (all bits set) typedef BFSMask<T> T_This; // "Import" the Parent Class typedef BFSMaskSized<sizeof(T)> T_Parent; typedef typename T_Parent::T_SINT T_SINT; #if FUNCTION_IN_PARENT typedef T_Parent T_MaskGen; #else typedef T_This T_MaskGen; template<int N> static T_SINT CreateMaskFromHighBitSized(typename BFSMaskSized<N>::T_SINT inmask); #endif template<typename TCMP> static T_SINT Create_NEZ(TCMP A) { //ReDefineType(const typename BFSMask<TCMP>::T_SINT,SA,A); //const typename BFSMask<TCMP>::T_SINT cmpmask = BFSMASK_NEZ(SA); const typename BFSMask<TCMP>::T_SINT cmpmask = BFSMASK_NEZ(A); #if DOESNT_COMPILE_WITH_GCC return(T_MaskGen::CreateMaskFromHighBitSized<sizeof(TCMP)>(cmpmask)); #else return(CreateMaskFromHighBitSized<sizeof(TCMP)>(cmpmask)); #endif } }; template<typename TVAL> TVAL BFWrappedInc(TVAL x,TVAL minval,TVAL maxval) { const TVAL diff = maxval-x; const TVAL mask = BFSMask<TVAL>::Create_NEZ(diff); const TVAL incx = x + 1; return(BFSelect_MASK(mask,incx,minval)); } SINT32 currentsnap = 0; SINT32 SetSnapshot() { currentsnap=BFWrappedInc<SINT32>(currentsnap,0,20); return(currentsnap); } }

    Read the article

  • MIPS: removing non alpha-numeric characters from a string

    - by Kron
    I'm in the process of writing a program in MIPS that will determine whether or not a user entered string is a palindrome. It has three subroutines which are under construction. Here is the main block of code, subroutines to follow with relevant info: .data Buffer: .asciiz " " # 80 bytes in Buffer intro: .asciiz "Hello, please enter a string of up to 80 characters. I will then tell you if that string was a palindrome!" .text main: li $v0, 4 # print_string call number la $a0, intro # pointer to string in memory syscall li $v0, 8 #syscall code for reading string la $a0, Buffer #save read string into buffer li $a1, 80 #string is 80 bytes long syscall li $s0, 0 #i = 0 li $t0, 80 #max for i to reach la $a0, Buffer jal stripNonAlpha li $v0, 4 # print_string call number la $a0, Buffer # pointer to string in memory syscall li $s0, 0 jal findEnd jal toUpperCase li $v0, 4 # print_string call number la $a0, Buffer # pointer to string in memory syscall Firstly, it's supposed to remove all non alpha-numeric characters from the string before hand, but when it encounters a character designated for removal, all characters after that are removed. stripNonAlpha: beq $s0, $t0, stripEnd #if i = 80 end add $t4, $s0, $a0 #address of Buffer[i] in $t4 lb $s1, 0($t4) #load value of Buffer[i] addi $s0, $s0, 1 #i = i + 1 slti $t1, $s1, 48 #if ascii code is less than 48 bne $t1, $zero, strip #remove ascii character slti $t1, $s1, 58 #if ascii code is greater than 57 #and slti $t2, $s1, 65 #if ascii code is less than 65 slt $t3, $t1, $t2 bne $t3, $zero, strip #remove ascii character slti $t1, $s1, 91 #if ascii code is greater than 90 #and slti $t2, $s1, 97 #if ascii code is less than 97 slt $t3, $t1, $t2 bne $t3, $zero, strip #remove ascii character slti $t1, $s1, 123 #if ascii character is greater than 122 beq $t1, $zero, strip #remove ascii character j stripNonAlpha #go to stripNonAlpha strip: #add $t5, $s0, $a0 #address of Buffer[i] in $t5 sb $0, 0($t4) #Buffer[i] = 0 #addi $s0, $s0, 1 #i = i + 1 j stripNonAlpha #go to stripNonAlpha stripEnd: la $a0, Buffer #save modified string into buffer jr $ra #return Secondly, it is supposed to convert all lowercase characters to uppercase. toUpperCase: beq $s0, $s2, upperEnd add $t4, $s0, $a0 lb $s1, 0($t4) addi $s1, $s1, 1 slti $t1, $s1, 97 #beq $t1, $zero, upper slti $t2, $s1, 123 slt $t3, $t1, $t2 bne $t1, $zero, upper j toUpperCase upper: add $t5, $s0, $a0 addi $t6, $t6, -32 sb $t6, 0($t5) j toUpperCase upperEnd: la $a0, Buffer jr $ra The final subroutine, which checks if the string is a palindrome isn't anywhere near complete at the moment. I'm having trouble finding the end of the string because I'm not sure what PC-SPIM uses as the carriage return character. Any help is appreciated, I have the feeling most of my problems result from something silly and stupid so feel free to point out anything, no matter how small.

    Read the article

  • Get non-overlapping dates ranges for prices history data

    - by Anonymouse
    Hello, Let's assume that I have the following table: CREATE TABLE [dbo].[PricesHist]( [Product] varchar NOT NULL, [Price] [float] NOT NULL, [StartDate] [datetime] NOT NULL, [EndDate] [datetime] NOT NULL ) INSERT [dbo].[PricesHist] ([Product], [Price], [StartDate], [EndDate]) VALUES (N'Apples', 4.9, CAST(0x00009D2C00000000 AS DateTime), CAST(0x00009D2C00000000 AS DateTime)) INSERT [dbo].[PricesHist] ([Product], [Price], [StartDate], [EndDate]) VALUES (N'Apples', 4.9, CAST(0x00009D2D00000000 AS DateTime), CAST(0x00009D2D00000000 AS DateTime)) INSERT [dbo].[PricesHist] ([Product], [Price], [StartDate], [EndDate]) VALUES (N'Apples', 2.5, CAST(0x00009D2E00000000 AS DateTime), CAST(0x00009D2E00000000 AS DateTime)) INSERT [dbo].[PricesHist] ([Product], [Price], [StartDate], [EndDate]) VALUES (N'Apples', 4.9, CAST(0x00009D3000000000 AS DateTime), CAST(0x00009D3000000000 AS DateTime)) INSERT [dbo].[PricesHist] ([Product], [Price], [StartDate], [EndDate]) VALUES (N'Apples', 4.9, CAST(0x00009D3100000000 AS DateTime), CAST(0x00009D3100000000 AS DateTime)) INSERT [dbo].[PricesHist] ([Product], [Price], [StartDate], [EndDate]) VALUES (N'Apples', 4.9, CAST(0x00009D3400000000 AS DateTime), CAST(0x00009D3400000000 AS DateTime)) INSERT [dbo].[PricesHist] ([Product], [Price], [StartDate], [EndDate]) VALUES (N'Apples', 2.5, CAST(0x00009D3500000000 AS DateTime), CAST(0x00009D3500000000 AS DateTime)) INSERT [dbo].[PricesHist] ([Product], [Price], [StartDate], [EndDate]) VALUES (N'Apples', 4.9, CAST(0x00009D3600000000 AS DateTime), CAST(0x00009D3600000000 AS DateTime)) INSERT [dbo].[PricesHist] ([Product], [Price], [StartDate], [EndDate]) VALUES (N'Apples', 4.9, CAST(0x00009D3700000000 AS DateTime), CAST(0x00009D3700000000 AS DateTime)) INSERT [dbo].[PricesHist] ([Product], [Price], [StartDate], [EndDate]) VALUES (N'Apples', 4.9, CAST(0x00009D3800000000 AS DateTime), CAST(0x00009D3800000000 AS DateTime)) INSERT [dbo].[PricesHist] ([Product], [Price], [StartDate], [EndDate]) VALUES (N'Apples', 4.9, CAST(0x00009D3A00000000 AS DateTime), CAST(0x00009D3A00000000 AS DateTime)) INSERT [dbo].[PricesHist] ([Product], [Price], [StartDate], [EndDate]) VALUES (N'Apples', 4.9, CAST(0x00009D3B00000000 AS DateTime), CAST(0x00009D3B00000000 AS DateTime)) INSERT [dbo].[PricesHist] ([Product], [Price], [StartDate], [EndDate]) VALUES (N'Apples', 2.5, CAST(0x00009D3C00000000 AS DateTime), CAST(0x00009D3C00000000 AS DateTime)) INSERT [dbo].[PricesHist] ([Product], [Price], [StartDate], [EndDate]) VALUES (N'Apples', 4.9, CAST(0x00009D3D00000000 AS DateTime), CAST(0x00009D3D00000000 AS DateTime)) INSERT [dbo].[PricesHist] ([Product], [Price], [StartDate], [EndDate]) VALUES (N'Apples', 4.9, CAST(0x00009D3E00000000 AS DateTime), CAST(0x00009D3E00000000 AS DateTime)) INSERT [dbo].[PricesHist] ([Product], [Price], [StartDate], [EndDate]) VALUES (N'Apples', 4.9, CAST(0x00009D3F00000000 AS DateTime), CAST(0x00009D3F00000000 AS DateTime)) INSERT [dbo].[PricesHist] ([Product], [Price], [StartDate], [EndDate]) VALUES (N'Apples', 4.9, CAST(0x00009D4100000000 AS DateTime), CAST(0x00009D4100000000 AS DateTime)) INSERT [dbo].[PricesHist] ([Product], [Price], [StartDate], [EndDate]) VALUES (N'Apples', 4.9, CAST(0x00009D4200000000 AS DateTime), CAST(0x00009D4200000000 AS DateTime)) INSERT [dbo].[PricesHist] ([Product], [Price], [StartDate], [EndDate]) VALUES (N'Apples', 2.5, CAST(0x00009D4300000000 AS DateTime), CAST(0x00009D4300000000 AS DateTime)) INSERT [dbo].[PricesHist] ([Product], [Price], [StartDate], [EndDate]) VALUES (N'Apples', 4.9, CAST(0x00009D4400000000 AS DateTime), CAST(0x00009D4400000000 AS DateTime)) INSERT [dbo].[PricesHist] ([Product], [Price], [StartDate], [EndDate]) VALUES (N'Apples', 4.9, CAST(0x00009D4500000000 AS DateTime), CAST(0x00009D4500000000 AS DateTime)) INSERT [dbo].[PricesHist] ([Product], [Price], [StartDate], [EndDate]) VALUES (N'Apples', 4.9, CAST(0x00009D4600000000 AS DateTime), CAST(0x00009D4600000000 AS DateTime)) INSERT [dbo].[PricesHist] ([Product], [Price], [StartDate], [EndDate]) VALUES (N'Apples', 4.9, CAST(0x00009D4800000000 AS DateTime), CAST(0x00009D4800000000 AS DateTime)) INSERT [dbo].[PricesHist] ([Product], [Price], [StartDate], [EndDate]) VALUES (N'Apples', 2.5, CAST(0x00009D4A00000000 AS DateTime), CAST(0x00009D4A00000000 AS DateTime)) As you can see, there are two prices on that month for Apples. 4.90 and 2.50. In order to tidy this table up, I need to get this information as a date range rather than a row per day as it currently is. I can obviously do this with Min and Max aggregates easily but the ranges overlap and other business code expect non-overlapping ranges. I also tried to achieve this with self joins and row_number(), but without much success... Here is what I'm trying to achieve as the output: Product | StartDate | EndDate | Price ------------------------------------------- Apples | 01 Mar 2010 | 02 Mar 2010 | 4.90 Apples | 03 Mar 2010 | 03 Mar 2010 | 2.50 Apples | 05 Mar 2010 | 09 Mar 2010 | 4.90 Apples | 10 Mar 2010 | 10 Mar 2010 | 2.50 Apples | 11 Mar 2010 | 16 Mar 2010 | 4.90 Apples | 17 Mar 2010 | 17 Mar 2010 | 2.50 Apples | 18 Mar 2010 | 23 Mar 2010 | 4.90 Apples | 24 Mar 2010 | 24 Mar 2010 | 2.50 Apples | 25 Mar 2010 | 30 Mar 2010 | 4.90 Apples | 31 Mar 2010 | 31 Mar 2010 | 2.50 What would please be the best approach to get this done? Thanks a lot in advance,

    Read the article

  • WCF errors in VS 2010/.Net 4 using sample publish/subscribe app from IDesign website

    - by Bill
    I am attempting to compile/run a sample WCF application from Juval Lowy's website (author of Programming WCF Services & founder of IDesign). The application is an example of a publish/subscribe 'traffic-light' application that requires using VS 2010/.Net 4. This is my first attempt at using anything other than VS 2008/Net 3.5. Initially I recieved the following binding error: "Configuration binding extension 'system.serviceModel/bindings/ netOnewayRelayBinding' could not be found." This error appeared to be resolved by amending the .Net 4 machine.config file, to incorporate the following references from the .Net 2 machine.config file. <xml> <bindingElementExtensions> <add name="tcpRelayTransport" type="Microsoft.ServiceBus.Configuration.TcpRelayTransportElement, Microsoft.ServiceBus, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" /> <add name="httpRelayTransport" type="Microsoft.ServiceBus.Configuration.HttpRelayTransportElement, Microsoft.ServiceBus, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" /> <add name="httpsRelayTransport" type="Microsoft.ServiceBus.Configuration.HttpsRelayTransportElement, Microsoft.ServiceBus, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" /> <add name="onewayRelayTransport" type="Microsoft.ServiceBus.Configuration.RelayedOnewayTransportElement, Microsoft.ServiceBus, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" /> <add name="webMessageEncoding" type="System.ServiceModel.Configuration.WebMessageEncodingElement, System.ServiceModel.Web, Version=4.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35"/> <add name="context" type="System.ServiceModel.Configuration.ContextBindingElementExtensionElement, System.ServiceModel, Version=4.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089"/> <add name="byteStreamMessageEncoding" type="System.ServiceModel.Configuration.ByteStreamMessageEncodingElement, System.ServiceModel.Channels, Version=4.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35"/> <add name="discoveryClient" type="System.ServiceModel.Discovery.Configuration.DiscoveryClientElement, System.ServiceModel.Discovery, Version=4.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35"/> </bindingElementExtensions> <bindingExtensions> <add name="webHttpBinding" type="System.ServiceModel.Configuration.WebHttpBindingCollectionElement, System.ServiceModel.Web, Version=4.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35"/> <add name="basicHttpContextBinding" type="System.ServiceModel.Configuration.BasicHttpContextBindingCollectionElement, System.ServiceModel, Version=4.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089"/> <add name="basicHttpRelayBinding" type="Microsoft.ServiceBus.Configuration.BasicHttpRelayBindingCollectionElement, Microsoft.ServiceBus, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" /> <add name="webHttpRelayBinding" type="Microsoft.ServiceBus.Configuration.WebHttpRelayBindingCollectionElement, Microsoft.ServiceBus, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" /> <add name="ws2007HttpRelayBinding" type="Microsoft.ServiceBus.Configuration.WS2007HttpRelayBindingCollectionElement, Microsoft.ServiceBus, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" /> <add name="netTcpRelayBinding" type="Microsoft.ServiceBus.Configuration.NetTcpRelayBindingCollectionElement, Microsoft.ServiceBus, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" /> <add name="netOnewayRelayBinding" type="Microsoft.ServiceBus.Configuration.NetOnewayRelayBindingCollectionElement, Microsoft.ServiceBus, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" /> <add name="netEventRelayBinding" type="Microsoft.ServiceBus.Configuration.NetEventRelayBindingCollectionElement, Microsoft.ServiceBus, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35"/> <add name="wsHttpContextBinding" type="System.ServiceModel.Configuration.WSHttpContextBindingCollectionElement, System.ServiceModel, Version=4.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089"/> <add name="netTcpContextBinding" type="System.ServiceModel.Configuration.NetTcpContextBindingCollectionElement, System.ServiceModel, Version=4.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089"/> </bindingExtensions> Unfortunately running the application results in the following security error: An error occurred creating the configuration section handler for system.serviceModel/client: That assembly does not allow partially trusted callers. (\TrafficLights\TrafficController\bin\Debug\TrafficController.vshost.exe.Config line 4) The sample source code is available for download at the following link: http://www.idesign.net/idesign/DesktopDefault.aspx?tabindex=-1&tabid=19&download=226 I know that Juval's code is not at fault here and that it must be something I'm doing wrong with my VS 2010 configuration. I have not been able to find a solution online. Could someone please steer me in the right direction as to how best to deal with this issue?

    Read the article

  • Xcode 3.2: Build & Analyze never finds any issues

    - by GamingHorror
    I've used the Clang Static Analyzer from the command line before. I wanted to try Xcode's built-in version via Build & Analyze. I never get any negative results even though i specially prepared my code with very obvious issues Clang was always able to point out: // over-releasing an object: [label release]; [label release]; // uninitialized vars, allocating but not freeing an object NSString* str; int number; CCLabel* newLabel = [[CCLabel alloc] initWithString:str fontName:str fontSize:number]; [newLabel setPosition:CGPointZero]; The result is always the same: a green checkbox, no issues. I read that C++ code can cause issues. I'm running this with cocos2d that includes box2d. Could this be a cause? Did anyone get results from Build & Analyze with the cocos2d engine? What else could it be? I also tried enabling the Static Analyzer Build Settings and then Build but the result was the same. I have restarted Xcode, cleaned all targets and emptied Xcode caches to no avail.

    Read the article

  • TVirtualStringTree - resetting non-visual nodes and memory consumption

    - by Remy Lebeau - TeamB
    I have an app that loads records from a binary log file and displays them in a virtual TListView. There are potentially millions of records in a file, and the display can be filtered by the user, so I do not load all of the records in memory at one time, and the ListView item indexes are not a 1-to-1 relation with the file record offsets (List item 1 may be file record 100, for instance). I use the ListView's OnDataHint event to load records for just the items the ListView is actually interested in. As the user scrolls around, the range specified by OnDataHint changes, allowing me to free records that are not in the new range, and allocate new records as needed. This works fine, speed is tolerable, and the memory footprint is very low. I am currently evaluating TVirtualStringTree as a replacement for the TListView, mainly because I want to add the ability to expand/collapse records that span multiple lines (I can fudge it with the TListView by incrementing/decrementing the item count dynamically, but this is not as straight forward as using a real tree). For the most part, I have been able to port the TListView logic and have everything work as I need. I notice that TVirtualStringTree's virtual paradigm is vastly different, though. It does not have the same kind of OnDataHint functionality that TListView does (I can use the OnScroll event to fake it, which allows my memory buffer logic to continue working), and I can use the OnInitializeNode event to associate nodes with records that are allocated. However, once a tree node is initialized, it sees that it remains initialized for the lifetime of the tree. That is not good for me. As the user scrolls around and I remove records from memory, I need to reset those non-visual nodes without removing them from the tree completely, or losing their expand/collapse states. When the user scrolls them back into view, I can re-allocate the records and re-initialize the nodes. Basically, I want to make TVirtualStringTree act as much like TListView as possible, as far as its virtualization is concerned. I have seen that TVirtualStringTree has a ResetNode() method, but I encounter various errors whenever I try to use it. I must be using it wrong. I also thought of just storing a data pointer inside each node to my record buffers, and I allocate and free memory, update those pointers accordingly. The end effect does not work so well, either. Worse, my largest test log file has ~5 million records in it. If I initialize the TVirtualStringTree with that many nodes at one time (when the log display is unfiltered), the tree's internal overhead for its nodes takes up a whopping 260MB of memory (without any records being allocated yet). Whereas with the TListView, loading the same log file and all the memory logic behind it, I can get away with using just a few MBs. Any ideas?

    Read the article

  • Receiving data with Winsock

    - by Tamir
    Right now, I'm programming the networking for my online game, and I'm not really sure what to do about receiving data. The problem is that I can't really guess the packet's size, so I thought of reading just 4 bytes from the packet and converting them to an int to know what's the packet's size. Then I'll just create a buffer in that size and receive the rest of the packet, is that a good idea? For your information, I'm using non-blocking i/o.

    Read the article

  • Help finding longest non-repeating path through connected nodes - Python

    - by Jordan Magnuson
    I've been working on this for a couple of days now without success. Basically, I have a bunch of nodes arranged in a 2D matrix. Every node has four neighbors, except for the nodes on the sides and corners of the matrix, which have 3 and 2 neighbors, respectively. Imagine a bunch of square cards laid out side by side in a rectangular area--the project is actually simulating a sort of card/board game. Each node may or may not be connected to the nodes around it. Each node has a function (get_connections()), that returns the nodes immediately around it that it is connected to (so anywhere from 0 to 4 nodes are returned). Each node also has an "index" property, that contains it's position on the board matrix (eg '1, 4' - row 1, col 4). What I am trying to do is find the longest non-repeating path of connected nodes given a particular "start" node. I've uploaded a couple of images that should give a good idea of what I'm trying to do: In both images, the highlighted red cards are supposedly the longest path of connected cards containing the most upper-left card. However, you can see in both images that a couple of cards that should be in the path have been left out (Romania and Maldova in the first image, Greece and Turkey in the second) Here's the recursive function that I am using currently to find the longest path, given a starting node/card: def get_longest_trip(self, board, processed_connections = list(), processed_countries = list()): #Append this country to the processed countries list, #so we don't re-double over it processed_countries.append(self) possible_trips = dict() if self.get_connections(board): for i, card in enumerate(self.get_connections(board)): if card not in processed_countries: processed_connections.append((self, card)) possible_trips[i] = card.get_longest_trip(board, processed_connections, processed_countries) if possible_trips: longest_trip = [] for i, trip in possible_trips.iteritems(): trip_length = len(trip) if trip_length > len(longest_trip): longest_trip = trip longest_trip.append(self) return longest_trip else: print card_list = [] card_list.append(self) return card_list else: #If no connections from start_card, just return the start card #as the longest trip card_list = [] card_list.append(board.start_card) return card_list The problem here has to do with the processed_countries list: if you look at my first screenshot, you can see that what has happened is that when Ukraine came around, it looked at its two possible choices for longest path (Maldova-Romania, or Turkey, Bulgaria), saw that they were both equal, and chose one indiscriminantly. Now when Hungary comes around, it can't attempt to make a path through Romania (where the longest path would actually be), because Romania has been added to the processed_countries list by Ukraine. Any help on this is EXTREMELY appreciated. If you can find me a solution to this, recursive or not, I'd be happy to donate some $$ to you. I've uploaded my full source code (Python 2.6, Pygame 1.9 required) to: http://www.necessarygames.com/junk/planes_trains.zip The relevant code is in src/main.py, which is all set to run.

    Read the article

  • TVirtualStringTree - resetting non-visual nodes and memory comsumption

    - by Remy Lebeau - TeamB
    I have an app that loads records from a binary log file and displays them in a virtual TListView. There are potentially millions of records in a file, and the display can be filtered by the user, so I do not load all of the records in memory at one time, and the ListView item indexes are not a 1-to-1 relation with the file record offsets (List item 1 may be file record 100, for instance). I use the ListView's OnDataHint event to load records for just the items the ListView is actually interested in. As the user scrolls around, the range specified by OnDataHint changes, allowing me to free records that are not in the new range, and allocate new records as needed. This works fine, speed is tolerable, and the memory footprint is very low. I am currently evaluating TVirtualStringTree as a replacement for the TListView, mainly because I want to add the ability to expand/collapse records that span multiple lines (I can fudge it with the TListView by incrementing/decrementing the item count dynamically, but this is not as straight forward as using a real tree). For the most part, I have been able to port the TListView logic and have everything work as I need. I notice that TVirtualStringTree's virtual paridigm is vastly different, though. It does not have the same kind of OnDataHint functionality that TListView does (I can use the OnScroll event to fake it, which allows my memory buffer logic to continue working), and I can use the OnInitializeNode event to associate nodes with records that are allocated. However, once a tree node is initialized, it sees that it remains initialized for the lifetime of the tree. That is not good for me. As the user scrolls around and I remove records from memory, I need to reset those non-visual nodes without removing them from the tree completely, or losing their expand/collapse states. When the user scrolls them back into view, I can re-allocate the records and re-initialize the nodes. Basically, I want to make TVirtualStringTree act as much like TListView as possible, as far as its virtualization is concerned. I have seen that TVirtualStringTree has a ResetNode() method, but I encounter various errors whenever I try to use it. I must be using it wrong. I also thought of just storing a data pointer inside each node to my record buffers, and I allocate and free memory, update those pointers accordingly. The end effect does not work so well, either. Worse, my largest test log file has ~5 million records in it. If I initialize the TVirtualStringTree with that many nodes at one time (when the log display is unfiltered), the tree's internal overhead for its nodes takes up a whopping 260MB of memory (without any records being allocated yet). Whereas with the TListView, loading the same log file and all the memory logic behind it, I can get away with using just a few MBs. Any ideas?

    Read the article

  • Non RBAC User Roles and Permissions System: a role with properties

    - by micha12
    We are currently designing a User Roles and Permissions System in our web application (ASP.NET), and it seems that we have several cases that do no fit within the classical Role-Based Access Control (RBAC). I will post several questions, each devoted to a particular case. This is my second question (the first question is here: http://stackoverflow.com/questions/2839797/non-rbac-user-roles-and-permissions-system-checking-the-users-city). We have the following case: we need to implement a Manager role in our web application. However, a Manager can belong to one or several companies (within a big group of companies for which we are creating this web app). Say, there can be “Manager of companies A and B”, “Manager of company C”, etc. Depending on the companies that the Manager belongs, he has access to certain operations: for example, he can communicate with clients only of those companies that he belongs to. That is, “Manager of companies A and B” can only have contacts with clients of companies A and B, and not with those of company C. He can also view clients’ details pages of companies A and B and not of C, etc. It seems that this case falls within the RBAC. However, this is not really the case. We will need to create a ManagerRole class that will have a Companies property – that is, this will not be just a role as a collection of permissions (like in the classical RBAC), but a role with properties! This was just one example of a role having properties. There will be others: for example, an Administrator role that will also belong to a number of companies and will also have other custom properties. This means that we will a hierarchy or roles classes: class Role – base class class ManagerRole : Role List Companies class AdministratorRole : Role List Companies Other properties We investigated pure RBAC and its implementation in several systems, and found no systems featuring a hierarchy or roles, each having custom properties. In RBAC, roles are just collections of permissions. We could model our cases using permission with properties, like ManagerPermission, AdministratorPermission, but this has a lot of drawbacks, the main being that we will not be able to assign a role like “Manager of Companies A and B” to a user directly, but will have to create a role containing a ManagerPermission for companies A and B… Moreover, a "Manager" seems to be rather a "role" (position in the company) rather than a "permission" from the linguistic point of view. Would be grateful for any ideas on this subject, as well as any experience in this field! Thank you.

    Read the article

  • NPR GLSL Tutorials

    - by anon
    Anyone have a good list of tutorials on doing Non photo realistic rendering with GLSL ? I have seen books on GLSL, and books on NPR, but very few books/tutorials on doing NPR with GLSL. (I want to do it with GLSL as I want real time). Thanks!

    Read the article

  • Grails validateable not work for non-persistent domain class

    - by Hoàng Long
    I followed the instruction here: http://www.grails.org/doc/latest/guide/7.%20Validation.html and added into config.groovy: grails.validateable.classes = [liningtest.Warm'] Then added in src/groovy/Warm.groovy (it's a non-persistent domain class): package liningtest import org.codehaus.groovy.grails.validation.Validateable class Warm { String name; int happyCite; Warm(String n, int h) { this.name = n; this.happyCite = h; } static constraints = { name(size: 1..50) happyCite(min: 100) } } But it just doesn't work (both "blank false" & "size: 0..25") for the "hasErrors" function. It always returns false, even when the name is 25. Is this a Grails bug, if yes, is there any work-around? I'm using Grails 1.3.3 UPDATE: I have updated the simplified code. And now I know that constraint "size" can't be used with "blank", but still does not work. My test class in test/unit/liningtest/WarmTests.groovy package liningtest import grails.test.* class WarmTests extends GrailsUnitTestCase { protected void setUp() { super.setUp() } protected void tearDown() { super.tearDown() } void testSomething() { def w = new Warm('Hihi', 3) assert (w.happyCite == 3) assert (w.hasErrors() == true) } } And the error I got: <?xml version="1.0" encoding="UTF-8" ?> <testsuite errors="1" failures="0" hostname="evolus-50b0002c" name="liningtest.WarmTests" tests="1" time="0.062" timestamp="2010-12-16T04:07:47"> <properties /> <testcase classname="liningtest.WarmTests" name="testSomething" time="0.062"> <error message="No signature of method: liningtest.Warm.hasErrors() is applicable for argument types: () values: [] Possible solutions: hashCode()" type="groovy.lang.MissingMethodException">groovy.lang.MissingMethodException: No signature of method: liningtest.Warm.hasErrors() is applicable for argument types: () values: [] Possible solutions: hashCode() at liningtest.WarmTests.testSomething(WarmTests.groovy:18) </error> </testcase> <system-out><![CDATA[--Output from testSomething-- ]]></system-out> <system-err><![CDATA[--Output from testSomething-- ]]></system-err> </testsuite> UPDATE 2: When I don't use Unit test, but try to call hasErrors in the controller, it runs but return false value. (hasErrors return false with Warm('Hihi', 3) ). Does anyone has a clue?

    Read the article

  • How to do a search from a list with non-prefix keywords

    - by aNui
    First of all, sorry if my english or my post got any mistakes. I am programming a program to search the name from the list and I need to find them if the keyword is not in front of the names (that's what I mean non-prefix) e.g. if I my list is the music instruments and I type "guit" to the search textbox. It should find the names "Guitar, Guitarrón, Acoustic Guitar, Bass Guitar, ..." or something like this Longdo Dictionary's search suggestion. here is my simple and stupid algorithm (that's all I can do) const int SEARCHROWLIMIT = 30; private string[] DoSearch(string Input, string[] ListToSearch) { List<string> FoundNames = new List<string>(); int max = 0; bool over = false; for (int k = 0; !over; k++) { foreach (string item in ListToSearch) { max = (max > item.Length) ? max : item.Length; if (k > item.Length) continue; if (k >= max) { over = true; break; } if (!Input.Equals("Search") && item.Substring(k, item.Length - k).StartsWith(Input, StringComparison.OrdinalIgnoreCase)) { bool exist = false; int i = 0; while (!exist && i < FoundNames.Count) { if (item.Equals(FoundNames[i])) { exist = true; break; } i++; } if (!exist && FoundNames.Count < SEARCHROWLIMIT) FoundNames.Add(item); else if (FoundNames.Count >= SEARCHROWLIMIT) over = true; } } } return FoundNames.ToArray(); } I think this algorithm is too slow for a large number of names and after several trial-and-error, I decided to add SEARCHROWLIMIT to breaks the operation And I also think there're some readymade methods that can do that. And another problem is I need to search music instruments by a category like strings, percussions, ... and by the country of origins. So I need to search them with filter by type and country. please help me. P.S. Me and my friends are just student from Thailand and developing the project to compete in Microsoft Imagine Cup 2010 and please become fan on our facebook page [KRATIB][3]. And we're so sorry we don't have much information in English but you can talk to us in English.

    Read the article

  • Non Document Centric SharePoint Workflow

    - by Dan Revell
    SharePoint workflows are document centric in that the base thing the workflow runs on has to be a thing; be it a document or just a list item. The workflow itself is task based, so stuff a user has to do. Now I can put any sort of code in these tasks that I want to and even put complex InfoPath forms in for the user to perform the task. This has been fine on all my previous workflows. But what if I want the tasks to be actual official forms themselves. The item that the workflow runs on is just some abstract concept like an event. An example could be an accident has happened. There isn't an accident form, but a whole set of forms that need to be completed by different people. Task forms aren't really a nice way to go, because it locks all the forms into the task list. You can only access the forms by not deleting the tasks when complete and going to the workflow summery and following the task links to the InfoPath forms or going straight to the tasks list and doing a filter on particular "accidents". These are official documents so ideally there would be a library for each type of document and the workflow would orchestrate the completion of the right forms. It would mean each task would have to create a new blank form and then link the user to that form. The user would go complete the form but then have to go back to the task form and click yes I've completed it until the workflow could progress. Well this is short of the workflow monitoring the forms library form for some completion trigger. But then it all gets messy with the user experience from clicking the link in the task email, to open the Infopath task form, to clicking the link in the subsequent Infopath library form and then return through these forms on completion. It just gets messy trying to retrofit this non document centric sort of workflow into SharePoint. I would really appreciate any input on what might be the best way to do this. Store the forms as task forms Store the forms as library forms and create/link from the task forms Store the forms as different infopath views, and use a forms library. The workflow would trigger variables that progress the view the infopath form shows. Using the same form template for both task forms and a forms library and when a task form is complete, copy the xml into the forms library to have a official record outside of the workflow. Thanks

    Read the article

  • How to do a search from a list with non-prefix keywords[Solved]

    - by aNui
    The Problem is Solved. Thanks for every answers. First of all, sorry if my english or my post got any mistakes. I am programming a program to search the name from the list and I need to find them even if the keyword is not in front of the names (that's what I mean non-prefix) e.g. if I my list is the music instruments and I type "guit" to the search textbox. It should find the names "Guitar, Guitarrón, Acoustic Guitar, Bass Guitar, ..." or something like this Longdo Dictionary's search suggestion. here is my simple and stupid algorithm (that's all I can do) const int SEARCHROWLIMIT = 30; private string[] DoSearch(string Input, string[] ListToSearch) { List<string> FoundNames = new List<string>(); int max = 0; bool over = false; for (int k = 0; !over; k++) { foreach (string item in ListToSearch) { max = (max > item.Length) ? max : item.Length; if (k > item.Length) continue; if (k >= max) { over = true; break; } if (!Input.Equals("Search") && item.Substring(k, item.Length - k).StartsWith(Input, StringComparison.OrdinalIgnoreCase)) { bool exist = false; int i = 0; while (!exist && i < FoundNames.Count) { if (item.Equals(FoundNames[i])) { exist = true; break; } i++; } if (!exist && FoundNames.Count < SEARCHROWLIMIT) FoundNames.Add(item); else if (FoundNames.Count >= SEARCHROWLIMIT) over = true; } } } return FoundNames.ToArray(); } I think this algorithm is too slow for a large number of names and after several trial-and-error, I decided to add SEARCHROWLIMIT to breaks the operation And I also think there're some readymade methods that can do that. And another problem is I need to search music instruments by a category like strings, percussions, ... and by the country of origins. So I need to search them with filter by type and country. please help me. P.S. Me and my friends are just student from Thailand and developing the project to compete in Microsoft Imagine Cup 2010 and please become fan on our facebook page [KRATIB][3]. And we're so sorry we don't have much information in English but you can talk to us in English.

    Read the article

  • Active Record/ORM vs Normal Forms?

    - by Arsenal
    Hello, I've been playing around with Active Record a bit, and I have noticed that A.C./ORM always uses the following database model when creating a one-to-one relationship Person id | country_id | name | ... Country id | tld | name | ... No I wondered, isn't this a violiation of the third Normal Form? This clearly states "Every non-prime attribute is non-transitively dependent on every key of the table". Well this country_id isn't dependent of personid is it? So is this wrong or am I just not getting the point?

    Read the article

< Previous Page | 132 133 134 135 136 137 138 139 140 141 142 143  | Next Page >