Search Results

Search found 11240 results on 450 pages for 'partition boot sector'.

Page 138/450 | < Previous Page | 134 135 136 137 138 139 140 141 142 143 144 145  | Next Page >

• Ubuntu Lucid: Erratic screen behaviour after boot

  - by fgysin

  In short: about 50% of the time I have a screwed up monitor setup after reboot. About 50% it is totally correct. Now the longer version: I updated my machine from 9.04 to 10.04 (via 9.10). At first I run into some monitor problems (I have a 3-monitor setup) because of the known bug in the new xserver driver for xinerama. This messes up behaviour if the mouse goes either left or above the screen number 0, i.e. I had to make my left-most monitor screen 0. Everything worked out fine finally, I got my 3-monitor setup back with xinerama enabled to get one big desktop streched over 3 screens. Now the fun part: Every time I start up my machine only one of the 3 monitors gets a signal and is woken up: it only recognizes the left-most monitor (screen 0) and crams all the desktop stuff into this one screen. If I go into nvidia settings I only see one physical device although all 3 are connected and have power. When I look into the xorg.conf I can still see my old setup with 3 devices, 3 screens, xinerama active etc... But I was totally unable to get 3 montitors to work. (I tried unplugging monitors, reconfiguring whole nvidia setup, ...) But it gets even better: When I restart my machine (i.e. choose the restart option from the Ubuntu menu) it shuts down and tries to restart. The restart then gets stuck after showing the Ubuntu splash screen with the 'loading bar' (the moving dots thingy) and I am forced to kill the machine by cutting power. But after the power cut the machine boots up normally and suddenly I get my 3 monitor setup back up working. That is until the next time I shut down and start up, where it all starts over again and I only have one monitor... (see above) I really have a hard time seeing where the error is. It must be that the restart boot somehow differs from the 'normal' boot. But the fact that it gets stuck and I need to cut power which then basically triggers a 'normal' boot does not really support this theory... My setup (please tell me if you need further info): 3 monitors as 3 screens as one desktop (with xinerama) 2 nvidia cards where screen 0 and 1 are on card 0 and screen 2 is on card 1 Ubuntu 10.04 Lucid Lynx (updated from 9.10, 9.04, ....) I would appreciate every idea on the subject, at the moment I really don't have any clue what to do...

  Read the article

• Deployment Workbench no longer available after PXE boot

  - by Patrick

  Our build process revolves around windows Deployment Workbench. Unfortunately this was setup by someone who is no longer with the company, and no-one has ever dared/needed to make any changes. The other day it stopped working. It turns out that one of our build guys started thinking about changing some stuff in it, clicked something and now it no longer works (He is saying now that he right clicked on the 'LAB' entry in 'Deployment points' and hit 'Update', which took some time to run through apparently). The job has fallen on me to resolve and frankly I'm not sure what I'm doing. I was wondering if someone with more experience than me can provide some pointers as to troubleshooting cos I'm feeling quite a lot in the dark here. On the server I have Deployment Workbench up and running (MMC snapin) version 3.0. There is a WDS service that appears to be running ok, as does the tFTPd service. Nothing specific to this in event logs. From the client side; PXE boot works and gets you to the Win PE launch, and it has the correct company logo as the background (proving to me that its loading win PE from the network). WPEINIT runs, and asks for domain credentials, here the team simply put User/Pass/Domain in the boxes and click ok. Normally the build would kick off. Instead they get an error message saying that the \NATBLU01\Distribution$ share isn't available. Checking \NATBLU01\Distribution$ shows that its there and accessible over the network. Security/permissions seem ok, even 'ANONYMOUS LOGON' has read access to that share so I don't see that being a problem. Digging the trace files from C:\MININT\SMSOSD\OSDLOGS\ after an attempt to run the build I can see an error saying much the same - <![LOG[Validating connection to \\NATBLU01\Distribution$]LOG]!><time="16:42:14.000+000" date="03-15-2012" component="LiteTouch" context="" type="1" thread="" file="LiteTouch"> <![LOG[FindFile: The file OSDConnectToUNC.exe could not be found in any standard locations.]LOG]!><time="16:42:14.000+000" date="03-15-2012" component="LiteTouch" context="" type="1" thread="" file="LiteTouch"> <![LOG[The network location cannot be reached. For information about network troubleshooting, see Windows Help.]LOG]!><time="16:42:24.000+000" date="03-15-2012" component="LiteTouch" context="" type="3" thread="" file="LiteTouch"> <![LOG[ERROR - Unable to map a network drive to \\NATBLU01\Distribution$.]LOG]!><time="16:42:24.000+000" date="03-15-2012" component="LiteTouch" context="" type="3" thread="" file="LiteTouch"> BDD.LOG shows much the same. Full copies of the .LOG files can both files be found here : BDD.LOG LITETOUCH.LOG I can get to a command prompt from the Win PE that boots from PXE, however there isn't any network stuff there. IPCONFIG returns nothing so none of the tests I would usually run resolve anything. I'm at a loss frankly. I did wonder if I could perhaps start a new build process but if the change to the DeploymentWorkbench has knocked it offline I don't think I'm going to be able to create a new deployment. Failing that; we do have a deployment point labeled type 'Media' which appears to be a DVD ISO image of one of the builds, but its dated 2008, is it possible to export the network build to .ISO and build from DVD? We are looking at new hardware to run this from anyway (for the impending Windows 7 roll out) so a temporary work round isn't going to be too much of a problem. All assistance is appreciated! EDIT : OK. Got it working again. Solution was close to Newmanth's idea. The problem was that our PE image didn't appear to be connecting the network. I had an older copy of the PE boot.WIM on a stick that I had been using for other purposes. I booted that and correctly got a network connection. Showed a correct internal IP and could ping out etc etc. However I was still getting the same errors in all the logs and in when wpeinit was running. What I did seperately was to update the PE image that DeploymentWorkbench was pushing out to display a different back ground. I wanted to prove that I was working in the correct place. Turns out that I wasn't. I went and looked at the other deployment stuff we had on this machine, Windows Deployment Services was installed and although all the install images are off line the boot image was online, so I uploaded the copy from my stick to that. Booted straight off. And fixed. Working. Yay! For anyone stumbling across this in the future you may find that although your deployment images are located in the DeploymentWorkbench, the Win PE boot image you are launching from is located in the associated Windows Deployment Services images.

  Read the article

• Bridging a Windows 7 and Ubuntu dual boot inside an OS

  - by matsko

  I have Windows 7 and Ubuntu installed on my local PC. They're both installed on separate partitions on the same machine, and when the computer boots up the user is given the option to choose which one they want to boot use as the OS. This all works fine, but I want to use Windows 7 instead of Ubuntu, I am required to restart the computer and boot up the other OS. Is is possible to use an "inline" tool that will allow to change between both OSs as if they were windows in Windows 7? Which tool would that be? Does anyone know of anything else than Parallels? Also are there any free tools that would do this?. Many Thanks.

  Read the article

• Will I be abled to access 2nd HDD from dual-boot

  - by Ruben

  I'm planning to have a dual-boot on my computer. I have 2 physical hard drives, one 500GB and one 2TB. What I want to do, is have a dual-boot setup (2 partitions, both 50 GB) for Windows 8 and Windows 7. But will I be able to access the 3rd partition on the disk, or the other disk from both OSs? In this case, it would be really useful to access files and install programs, because I could use them on both OSs, as long as I have the same registry keys.

  Read the article

• Home Server restore fails cannot find boot device

  - by Tim Heuer

  I am using Windows Home Server to backup my PCs. I recently had a hard drive failure on one of my WHS connected PCs and obtained an identical sized/speed drive for my laptop. I used the latest home server restore CD and did the restore. It said it completed successfully. Upon reboot, it says 'cannot find boot device' and lists all my drives (hard drive, cd, network book) indicating no valid operating system was found. I boot using the Win7 repair disk and while it doesn't see the operating system, it sees the drive and if I go into a command prompt, I can see all my data on the drive. My laptop is Windows 7 64-bit Ultimate. I've tried most everything I can think of. I'm a technical user (software developer) so I'm pretty aware of how things work (or should). I don't feel like I'm missing a simple step here.

  Read the article

• Supermicro MBD-X9DRL-IF-B and 8 X Hynix 4Gb DDR3 ECC dont boot

  - by Avi Keinan

  I have a custom build server with 2 Xeon E5-2609 and Supermicro MBD-X9DRL-IF-B. Right now the server has 4X Hynix 4Gb 2Rx8 PC3L-10600R-9-10-B0 HMT351R7BFR8A. and its working great. We baught another 4 from the same series of memory, when we installed all the ram (4 sticks already installed and we added 4 new sticks) the server didn't boot. When we replaced the current memory with the new memory - the server did boot. Right now we are in a problem because we need to extend this server ram but the motherboard don't run with 8X4Gb. Any ideas why? I have attached a picture with one of the current memory stick and one of the new memory stick. Thanks in advence.

  Read the article

• Fedora Core 11 won't boot without a monitor

  - by feihtthief

  I have a P4 system that I installed Fedora 11 on. It will not boot without a monitor attached. The monitor can be off (not even have power plugged in), but must be attached. Without a monitor the hard disk thrashes around a bit like it's starting up services, but does not get to the point where I can ssh into the box. I have set the default runlevel to 3 and removed the rhgb entry from grub. Any suggestions welcome. Edit: I have already set the run-level to 3. The machine boots up fine with the monitor plugged in to the point where I can SSH into it. as soon as i unplug the monitor and reboot, it will not boot to that point.

  Read the article

• CentOS 5 - Unable to resolve addresses for NFS mounts during boot

  - by sagi

  I have a few servers running CentOS 5.3, and am trying to get 2 NFS mount-points to mount automatically on boot. I added 2 lines similar to the following to fstab: server1:/path1 /path1 nfs soft 0 0 server2:/path2 /path2 nfs soft 0 0 When I run 'mount -a' manually, the mount points are properly mounted as expected. However, when I reboot the machine, only /path2 is mounted. For /path1 I get the following error: mount: can't get address for server1 It obviously looks like a DNS issue, but the record is properly configured in all the DNS servers and is mounted properly if I re-try the mount after the reboot is completed. I could properly fix this by using IP address instead of hostnames in /etc/fstab or adding server1 to /etc/hosts but I would rather not do that. What might be the reason for failing to resolve this specific address during boot time? Why the problem is only with the 1st mount point and the 2nd is properly mounted despite having identical configuration?

  Read the article

• IDE Motherboard to Boot from a SATA 1T Hdd

  - by JavaMan

  I want to use my SATA HDD in my very old ASUS A7V8X-X motherboard (made in 2003). I intended to buy a cheap adapter for this. Say something similar to this one: http://www.cooldrives.com/satoidecofor.html But would there be any issue if I want to boot from this SATA drive? My impression is that these kind of adapters convert SATA signal and commands to PATA directly and such a low level conversion should be transparent to the motherboard and BIOS - in case the BIOS doesn't support SATA. And, for my motherboard, it sure doesn't. Does anyone ever used such a kind of adapter to support a boot drive? Any success sorry?

  Read the article

• Dell Latitude E6420 dual-boot Ubuntu + Windows 7 Optimus graphics problems

  - by Ryan

  I have a Dell Latitude E6420 laptop with Ubuntu 12.04 alongside Windows 7 (dual-boot) docked in a docking station with 2 DVI outputs. It took me a week of tinkering to get the dual external monitors to work in Ubuntu, and I had to disabled the "Optimus" feature in the BIOS. But now neither external monitor is detected in Windows, and the resolution is also very low. Do you know how I can successfully dual-boot Windows 7 and Ubuntu on this machine using my 2 external DVI monitors? I have an open question here too, trying to resolve this same issue: http://askubuntu.com/questions/146933/dock-with-dual-external-dvi-monitors-with-intel-nvidia-optimus

  Read the article

• How set default Kernal boot in Ubuntu

  - by Daniel

  I want to default boot an older Kernal of Ubuntu, what is the best way to do this?

  Read the article

• Ubuntu hangs on boot when NFS-mounting entries in /etc/fstab, but they mount cleanly otherwise

  - by lorin

  I'm managing several Ubuntu 9.10 servers that NFS mount several folders (including /home). I'd like these folders to be mounted at boot time. I would like to have several entries in my /etc/fstab to accomplish this, e.g. 192.168.1.100:/home /home nfs rw 0 0 192.168.1.100:/usr/ansys_inc /ansys_inc nfs ro 0 0 Unfortunately, with this configuration, the servers usually (although not always) hang during the bootup sequence when trying to do the NFS mount. if I comment out these fstab entries, reboot the machine, uncomment them and mount them manually using the shell, the folders mount cleanly. I'm not sure how to go about debugging this problem. It seems like it has something to do with the boot sequence, that some relevant process hasn't been started by the time the OS tries to mount the folders.

  Read the article

• add script on boot linux machine

  - by user1546679

  I have one script to start a service on my ubuntu. I added it on boot machine using "# update-rc.d projeto defaults". But it still doesn't start with the boot machine. I think is because I am using other user to start the script "su - www-data -c ...". But I am not sure, because I run the update-rc.d command as root. When I execute the script from a terminal, it asks the password of the user www-data. Does anyone know what is happening? Thanks a lot! Felipe #!/bin/bash # /var/www/boinc/projeto/bin/start function action { su - www-data -c "/var/www/boinc/projeto/bin/$1" } case $1 in start|stop|status) action $1 ;; *) echo "ERRO: usar $0 (start|stop|status)" exit 1 ;; esac

  Read the article

• GRUB2 Boot Configuration

  - by MA1

  Recently i installed GRUB2, everything is working fine. When my system is started my monitor is showing something like the following "Minimal BASH-Like line editing is supported. For the first word, TAB lists possible command completions. Anywhere else TAB lists the possible completions of a device/filename." Press "Esc" key to enter the menu. Boot windows... and when i press the Esc key it then shows the GRUB2 menu showing list of operating systems installed on my system How the remove "Minimal BASH-Like line editing ...." text. I only need this line Press "Esc" key to enter the menu. Boot windows... Note: Both my WindowsXP and Fedora12 are working fine and loading with no problem.

  Read the article

• Windows 7 strange boot issue

  - by JL

  Recently I installed an SSD drive, its now my primary boot drive (OCZ Vertex Turbo 60GB). I'm running Win 7 (64bit). Now I am not sure exactly where the fault lies, but when I do a restart from within Windows, the computer will boot and enter into the loading windows portion, however won't progress beyond there. My solution is to manually hit the reset switch, and then when it boots it enters into a windows menu that offers a start up repair or start windows normally. I select start windows normally, and then it boots fine. I am not entirely sure why I can't just restart the computer from windows normally though. The SSD drive works perfectly, and not even sure if it is the cause to this problem. Any ideas on this?

  Read the article

• Keyboard not responding during boot

  - by Peri

  My keyboard just stopped responding during boot. So I cannot go to BIOS or select system which I want to start. It is USB keyboard and it was working before. I borrowed PS2 keyboard and it also isn't working during boot. Lately I have been having problems with hard disk. Once every 2-5 minutes LED was on for 30 seconds and win7 wasn't responsive. I connected disk to another controller on motherboard and seems it is working now. All that suggests that to me that that motherboard is broken. What can I check? Or maybe you have some other suggestions?

  Read the article

• How can I determine the sector size on an external hard drive?

  - by sigint

  Hard drives are transitioning from 512 byte to 4096 byte sector sizes, and it looks like Windows XP won't support these newer drives without additional software (such as WDalign from Western Digital) My question is: how does this affect external hard drives? I'll be buying a 1TB USB external drive, and it'll be plugged into a mix of Windows 7 and XP machines. Is there an easy way to tell what the sector size on an external hard drive is?

  Read the article

• /etc/rc.local doesn't execute apache tomcat startup script on boot

  - by user119720

  I'm having some problem with my centOS machine.I want to insert a line inside the rc.local to execute apache tomcat on startup. Below are the configuration for /etc/rc.local #!/bin/sh # # This script will be executed *after* all the other init scripts. # You can put your own initialization stuff in here if you don't # want to do the full Sys V style init stuff. touch /var/lock/subsys/local /opt/apache-jakarta/bin/startup.sh Unfortunately,the apache tomcat does not start on the boot time. I've already execute the script manually and it is working without any issues. Is there any specific syntax to put script inside the rc.local?Or did I forgetting something?Please Advice.Thanks. EDIT: My boot.log only show this output: Dec 17 21:04:53 localhost NET[2969]: /sbin/dhclient-script : updated /etc/resolv.conf

  Read the article

• Master Boot Record

  - by Crystal

  I'm trying to understand what an MBR is. I know it is used to boot the device, like a compact flash card. If you had five 1GB CF card from SanDisk for a camera, would there be any reason for the manufacturer to have different MBRs? It seems like to me, if for some reason one CF card wouldn't boot, you could copy the MBR from a working CF card and write it to the non-working CF card. Would this MBR for a SanDisk card work on the same size Western Digital card for the same use? Thanks!

  Read the article

• Missing files when Windows 7 returns from hibernate w/ dual boot

  - by Arthur N

  I have a dual-boot setup with Ubuntu (lucid) and Windows 7. I have the Windows file system shared on Ubuntu through Samba. Occasionally, I am working on Windows and my machine will go into hibernate (i.e. when the battery level is critical). By default, my GRUB settings boot me into Ubuntu. So when I get back to my PC, sometimes I just hop into Ubuntu instead of going back to Windows. However, if I write any files to the Windows file system during that Ubuntu session, the next time I do go back to Windows (which resumes from hibernate), those files are missing. Obviously, the state of the actual file system and the hibernate snapshot become out of sync, and Windows chooses the hibernate snapshot, overriding any changes I may have made thru Ubuntu. For now, I've disabled the hibernate option in the Windows power settings, but is there any utility I can use to get back some of those missing files?

  Read the article

• Missing files when Windows 7 returns from hibernate w/ dual boot

  - by Arthur N

  I have a dual-boot setup with Ubuntu (lucid) and Windows 7. I have the Windows file system shared on Ubuntu through Samba. Occasionally, I am working on Windows and my machine will go into hibernate (i.e. when the battery level is critical). By default, my GRUB settings boot me into Ubuntu. So when I get back to my PC, sometimes I just hop into Ubuntu instead of going back to Windows. However, if I write any files to the Windows file system during that Ubuntu session, the next time I do go back to Windows (which resumes from hibernate), those files are missing. Obviously, the state of the actual file system and the hibernate snapshot become out of sync, and Windows chooses the hibernate snapshot, overriding any changes I may have made thru Ubuntu. For now, I've disabled the hibernate option in the Windows power settings, but is there any utility I can use to get back some of those missing files?

  Read the article

• Encrypt two drives with Truecrypt with password before boot

  - by Deshroom

  i'm using laptop and PC with single HDD with full disk encryption. I know how works truecrypt on single drive because i use it everyday. My second laptop has 2 HHDs. My question is how to encrypt first 128GB SSD and second 1TB HDD in same way. I have multiple applications installed on second drive so i want to have it accessible during boot in ex. Steam in installed on second drive and it starts with windows. How to do it? can i encrypt two drives in truecrypt and unlock it via password before boot? My main reason is i want to RMA laptop without removing disks or data - my data need to be encrypted. Thank you.

  Read the article

• Can I use PCI SATA Addon card and Boot from a HDD attached to the card

  - by POTHEN

  Can I boot from a HDD which is running from a PCI SATA expansion card.

  Read the article

• Converted VmWare Image does not boot in Virtual Box

  - by vBox Question

  I have a .vddx virtual image which boots in VmWare, but I'm having trouble getting it to work with Sun Virtual Box. In Sun Virtual Box, I created a new Virtual Machine and pointed it at the vddx file from VmWare. When I try to boot the virtual machine, Sun Virtual Box says that the volume is not bootable. VmWare is able to boot from this virtual machine. Does anyone have any suggestions about what might be causing the problem? Is there a conversion utility that I need to run? Any debugging options that I could turn on?

  Read the article

• Server refuses to boot when Raid5 disk is disconnected - /root/ missing

  - by Ronni

  I recently set up a NAS server running a Debian OS (6.0.4) It contains 4 disks, 3 of them are in a Raid5 array, while the last one is used for the OS. To simulate a disk-failure I unplugged one of the raid disks, which resulted in the OS being unable to boot. It started the boot, recognized that md0 (the raid array) was running on 2/3 disks, and then threw a few errors. It was unable to find the following directories: /dev/root on /root, /dev on /root/dev, /sys on /root/sys, /proc on /root/proc It appears this happens regardless of which raid disk is removed. These directories are supposed to be on /dev/sdd my system disk. Output from fstab and blkid : http://dl.dropbox.com/u/6017799/NASOutput.txt If you need additional info, please let me know.

  Read the article

< Previous Page | 134 135 136 137 138 139 140 141 142 143 144 145  | Next Page >