Search Results

Search found 27501 results on 1101 pages for 'power view'.

Page 14/1101 | < Previous Page | 10 11 12 13 14 15 16 17 18 19 20 21  | Next Page >

  • On a dual-GPU laptop, is using the discrete GPU ever more power efficient?

    - by Mahmoud Al-Qudsi
    Given a laptop with a dual integrated/discrete GPU configuration, is it ever more power efficient to use the discrete GPU instead of the integrated? Obviously when writing an email or working on a spreadsheet, the integrated GPU will always use less power. But let's say you're doing something graphics-medium but not graphics-intensive/heavy - is there a point where it actually makes sense to fire up the discrete GPU, not for performance but for power-saving reasons? Off the top of my head, I can think of a scenario where the external GPU supports hardware decoding of a particular video codec - I'd imagine there is a "price point" where using the GPU saves more energy than decoding that fully in software would. But I think most GPUs, integrated or discrete, pretty much decode just the plain-Jane h264. But maybe there is something more complicated, perhaps if you're doing something like desktop/windowing animations or a flash animation on a website (not an embedded flash video) - maybe the discrete GPU will use enough less power to make up for switching to it? I guess this question can be summed up as to whether or not you can say beyond doubt that if you don't care for performance on a laptop with two GPUs, always use the integrated GPU for maximum battery life.

    Read the article

  • High Power Consumption and Wakeups on my Asus X54H with 12.04

    - by Marogian
    So I've been using powertop to try and reduce the power consumption on my laptop as I only seem to get about 3 hours of battery. From reading other threads on here it seems my power consumption and wakeups are strangely high, here's a summary: The battery reports a discharge rate of 10.2 W Summary: 651.8 wakeups/second, 0.0 GPU ops/second and 0.0 VFS ops/sec The things which stand out as odd: 1.31 W 4.0 ms/s 166.7 Interrupt PS/2 Touchpad / Keyboard / Mouse So more than 10% of my battery is being consumed by my touchpad/keyboard? That doesn't seem right. 548 mW 34.3 ms/s 45.9 Process compiz 5% from Compiz. Is this correct? 376 mW 1.8 ms/s 47.5 Interrupt [51] i915 298 mW 1.4 ms/s 37.7 Timer tick_sched_timer Another few percent from these things- not quite sure what they are. For reference I've installed Laptop Mode Tools, Jupiter (on power save), the CPU governor is definitely on powersave and brightness is on minimum. What else can I do/Any ideas? I've seen other posts on here reporting laptop battery lives of ~8 hours and power consumption of 4W rather than my 10W... Thanks!

    Read the article

  • django/python: is one view that handles two sibling models a good idea?

    - by clime
    I am using django multi-table inheritance: Video and Image are models derived from Media. I have implemented two views: video_list and image_list, which are just proxies to media_list. media_list returns images or videos (based on input parameter model) for a certain object, which can be of type Event, Member, or Crag. The view alters its behaviour based on input parameter action (better name would be mode), which can be of value "edit" or "view". The problem is that I need to ask whether the input parameter model contains Video or Image in media_list so that I can do the right thing. Similar condition is also in helper method media_edit_list that is called from the view. I don't particularly like it but the only alternative I can think of is to have separate (but almost the same) logic for video_list and image_list and then probably also separate helper methods for videos and images: video_edit_list, image_edit_list, video_view_list, image_view_list. So four functions instead of just two. That I like even less because the video functions would be very similar to the respective image functions. What do you recommend? Here is extract of relevant parts: http://pastebin.com/07t4bdza. I'll also paste the code here: #urls url(r'^media/images/(?P<rel_model_tag>(event|member|crag))/(?P<rel_object_id>\d+)/(?P<action>(view|edit))/$', views.image_list, name='image-list') url(r'^media/videos/(?P<rel_model_tag>(event|member|crag))/(?P<rel_object_id>\d+)/(?P<action>(view|edit))/$', views.video_list, name='video-list') #views def image_list(request, rel_model_tag, rel_object_id, mode): return media_list(request, Image, rel_model_tag, rel_object_id, mode) def video_list(request, rel_model_tag, rel_object_id, mode): return media_list(request, Video, rel_model_tag, rel_object_id, mode) def media_list(request, model, rel_model_tag, rel_object_id, mode): rel_model = tag_to_model(rel_model_tag) rel_object = get_object_or_404(rel_model, pk=rel_object_id) if model == Image: star_media = rel_object.star_image else: star_media = rel_object.star_video filter_params = {} if rel_model == Event: filter_params['event'] = rel_object_id elif rel_model == Member: filter_params['members'] = rel_object_id elif rel_model == Crag: filter_params['crag'] = rel_object_id media_list = model.objects.filter(~Q(id=star_media.id)).filter(**filter_params).order_by('date_added').all() context = { 'media_list': media_list, 'star_media': star_media, } if mode == 'edit': return media_edit_list(request, model, rel_model_tag, rel_object_id, context) return media_view_list(request, model, rel_model_tag, rel_object_id, context) def media_view_list(request, model, rel_model_tag, rel_object_id, context): if request.is_ajax(): context['base_template'] = 'boxes/base-lite.html' return render(request, 'media/list-items.html', context) def media_edit_list(request, model, rel_model_tag, rel_object_id, context): if model == Image: get_media_edit_record = get_image_edit_record else: get_media_edit_record = get_video_edit_record media_list = [get_media_edit_record(media, rel_model_tag, rel_object_id) for media in context['media_list']] if context['star_media']: star_media = get_media_edit_record(context['star_media'], rel_model_tag, rel_object_id) else: star_media = None json = simplejson.dumps({ 'star_media': star_media, 'media_list': media_list, }) return HttpResponse(json, content_type=json_response_mimetype(request)) def get_image_edit_record(image, rel_model_tag, rel_object_id): record = { 'url': image.image.url, 'name': image.title or image.filename, 'type': mimetypes.guess_type(image.image.path)[0] or 'image/png', 'thumbnailUrl': image.thumbnail_2.url, 'size': image.image.size, 'id': image.id, 'media_id': image.media_ptr.id, 'starUrl':reverse('image-star', kwargs={'image_id': image.id, 'rel_model_tag': rel_model_tag, 'rel_object_id': rel_object_id}), } return record def get_video_edit_record(video, rel_model_tag, rel_object_id): record = { 'url': video.embed_url, 'name': video.title or video.url, 'type': None, 'thumbnailUrl': video.thumbnail_2.url, 'size': None, 'id': video.id, 'media_id': video.media_ptr.id, 'starUrl': reverse('video-star', kwargs={'video_id': video.id, 'rel_model_tag': rel_model_tag, 'rel_object_id': rel_object_id}), } return record # models class Media(models.Model, WebModel): title = models.CharField('title', max_length=128, default='', db_index=True, blank=True) event = models.ForeignKey(Event, null=True, default=None, blank=True) crag = models.ForeignKey(Crag, null=True, default=None, blank=True) members = models.ManyToManyField(Member, blank=True) added_by = models.ForeignKey(Member, related_name='added_images') date_added = models.DateTimeField('date added', auto_now_add=True, null=True, default=None, editable=False) class Image(Media): image = ProcessedImageField(upload_to='uploads', processors=[ResizeToFit(width=1024, height=1024, upscale=False)], format='JPEG', options={'quality': 75}) thumbnail_1 = ImageSpecField(source='image', processors=[SmartResize(width=178, height=134)], format='JPEG', options={'quality': 75}) thumbnail_2 = ImageSpecField(source='image', #processors=[SmartResize(width=256, height=192)], processors=[ResizeToFit(height=164)], format='JPEG', options={'quality': 75}) class Video(Media): url = models.URLField('url', max_length=256, default='') embed_url = models.URLField('embed url', max_length=256, default='', blank=True) author = models.CharField('author', max_length=64, default='', blank=True) thumbnail = ProcessedImageField(upload_to='uploads', processors=[ResizeToFit(width=1024, height=1024, upscale=False)], format='JPEG', options={'quality': 75}, null=True, default=None, blank=True) thumbnail_1 = ImageSpecField(source='thumbnail', processors=[SmartResize(width=178, height=134)], format='JPEG', options={'quality': 75}) thumbnail_2 = ImageSpecField(source='thumbnail', #processors=[SmartResize(width=256, height=192)], processors=[ResizeToFit(height=164)], format='JPEG', options={'quality': 75}) class Crag(models.Model, WebModel): name = models.CharField('name', max_length=64, default='', db_index=True) normalized_name = models.CharField('normalized name', max_length=64, default='', editable=False) type = models.IntegerField('crag type', null=True, default=None, choices=crag_types) description = models.TextField('description', default='', blank=True) country = models.ForeignKey('country', null=True, default=None) #TODO: make this not null when db enables it latitude = models.FloatField('latitude', null=True, default=None) longitude = models.FloatField('longitude', null=True, default=None) location_index = FixedCharField('location index', length=24, default='', editable=False, db_index=True) # handled by db, used for marker clustering added_by = models.ForeignKey('member', null=True, default=None) #route_count = models.IntegerField('route count', null=True, default=None, editable=False) date_created = models.DateTimeField('date created', auto_now_add=True, null=True, default=None, editable=False) last_modified = models.DateTimeField('last modified', auto_now=True, null=True, default=None, editable=False) star_image = models.ForeignKey('Image', null=True, default=None, related_name='star_crags', on_delete=models.SET_NULL) star_video = models.ForeignKey('Video', null=True, default=None, related_name='star_crags', on_delete=models.SET_NULL)

    Read the article

  • Opposite method of math power adding numbers

    - by adopilot
    I have method for converting array of Booleans to integer. It looks like this class Program { public static int GivMeInt(bool[] outputs) { int data = 0; for (int i = 0; i < 8; i++) { data += ((outputs[i] == true) ? Convert.ToInt32(Math.Pow(2, i)) : 0); } return data; } static void Main(string[] args) { bool[] outputs = new bool[8]; outputs[0] = false; outputs[1] = true; outputs[2] = false; outputs[3] = true; outputs[4] = false; outputs[5] = false; outputs[6] = false; outputs[7] = false; int data = GivMeInt(outputs); Console.WriteLine(data); Console.ReadKey(); } } Now I want to make opposite method returning array of Booleans values As I am short with knowledge of .NET and C# until now I have only my mind hardcoding of switch statement or if conditions for every possible int value. public static bool[] GiveMeBool(int data) { bool[] outputs = new bool[8]; if (data == 0) { outputs[0] = false; outputs[1] = false; outputs[2] = false; outputs[3] = false; outputs[4] = false; outputs[5] = false; outputs[6] = false; outputs[7] = false; } //After thousand lines of coed if (data == 255) { outputs[0] = true; outputs[1] = true; outputs[2] = true; outputs[3] = true; outputs[4] = true; outputs[5] = true; outputs[6] = true; outputs[7] = true; } return outputs; } I know that there must be easier way.

    Read the article

  • MVC: Model View Controller -- does the View call the Model?

    - by Gary Green
    I've been reading about MVC design for a while now and it seems officially the View calls objects and methods in the Model, builds and outputs a view. I think this is mainly wrong. The Controller should act and retrieve/update objects inside the Model, select an appropriate View and pass the information to it so it may display. Only crude and rudiementary PHP variables/simple if statements should appear inside the View. If the View gets the information it needs to display from the Model, surely there will be a lot of PHP inside the View -- completely violating the point of seperating presentation logic.

    Read the article

  • refresh table view iphone

    - by Florent
    Hi all !! So i've set a table view, i have set a system which set if the row have been already selected, i set checkmarck acessory for a row which have been seen, i write the row in a plist to an int value. It work good but only when i restart the app or reload the table view in my navigation controller. I mean when i select a row it pushes a view controller, then when i go back to the table view checkmark disappear and we do not know if the row have already been selected only when the app restart. So is there a way to refresh the table view ? ? in the view will appear for example ? ? thanks to all !!!!

    Read the article

  • How to use Eclipse's Display View for Debug?

    - by jzd
    At the link below it explains that the "display view allows you to manipulate live code in a scrapbook type fashion (see Figure 8). To manipulate a variable, simply type the name of the variable in the Display view, and you'll be greeted with a familiar content assist." http://www.ibm.com/developerworks/library/os-ecbug/ However, I am having trouble getting it to work. I have the view open but all the buttons are disabled. I have tried putting code in the view, selecting code in the view, selecting code in other views, while running and while not running debug, but the only button that is ever enabled on the view is "clear console". Suggestions on what I am doing wrong?

    Read the article

  • how to apply the center of image view for another image view center

    - by maddy
    hi, I am developing image redraw app. i know the center of one image view which is having scaling property. i.e it can change it frame and center . that to be applied to another view center. when i apply center to newly formed Image view it giving wrong center because of the previous image view is having scaling property. so how can i get exact center to my new image view from previous imageview

    Read the article

  • Selection on table view causes parent view to change

    - by Tereno
    Hi there, I'm working on an iPad app and here's my scenario: I have a view which contains a table view inside of it. When the user selects an item on the table view, I would like the parent's view to change in a navigational manner. For those of you that have an iPad, this would be akin to the "Settings" app. But I guess in the "Settings" app, the right pane is composed of a grouped table view right? Is what I'm trying to do possible? Thanks

    Read the article

  • Inserting code to HTML view from a pop up initiated from visual view

    - by objectiveME
    I am trying to insert html into the HTML view.What i have done is to have tinymce advanced(a wordpress plugin) button that throws a popup and in it is all the necessary things to insert the html.The tinymce buttons are however only visible on the visual view. Question 1: Is it a plugin or hack that can allow one to parse html inside the visual view Question 2: Is it possible to insert html code to the html view from a popup initiated from the visual view

    Read the article

  • Which part of the computer needs all the power from the PSU?

    - by Xeoncross
    A couple years ago I was building a new Core 2 Quad system and after reading all the reviews was convinced that I would need at least a 400 watt power supply unit (PSU). I bought a 500W Antec EarthWatts However, last year I bought a Kill-A-Watt power meter to test some things around our house and found that my PC was only using 80W of power while idle! (C2Q, 4GB RAM, SATA HD, & DVD burner) Well, here I am building another computer with a 65watt Core 2 CPU in it and I'm wondering if I can skimp out this time and get a 300watt or so unit since my usage doesn't seem to be what everyone claims it is. I'm sure that the people in the reviews who exhausted 500watt PSU weren't lying - so what is it that uses all that? The high-end dual SLI video cards? Lots of SATA drives? Overclocking?

    Read the article

  • Can a power failure or forceful shutdown damage hardware?

    - by Vilx-
    In an unrelated Internet forum I got into a discussion about hardware damage from forceful shutdowns (holding the power button for 5 seconds) and power failures. I was in the opinion that normal PC hardware does not suffer from this - after all, it's not much different than what they experience under a standard shutdown. But another person thought that it could do physical harm to the hard drive and possibly other components as well. He also said that the journaling features of filesystems are useless in face of power failures and were intended to help mitigate damage from system crashes. Now... I think this is nonsense, but then again I lack the experience and knowledge to say it with certainty. Perhaps someone else is more knowledgeable in this area and can shed light on this burning issue? :)

    Read the article

  • Problem with Graphics Card, Power Supply or Mother Board?

    - by Rick Siegert
    I have a problem that is driving me to the edge. My graphics card periodically looses power for a moment, then comes back. Once in a while it takes much longer, like 5 minutes. I have always tried rebooting during that period, since I don't know then. Black screen, with a no power message across my monitor. All equipment is only a few months old. The Motherboard is a few months old, MSI N9A2 Platinum Revision 1 (AMD). The Video Card is a Gigabyte Radeon HD 4850 1GB. The power supply is an Ultra 700w My OS is Xp Pro, sp3 Any ideas or suggestions how to solve this

    Read the article

  • Does a Samsung G3 Station external hard drive stop working when power supply is too high?

    - by Cacovsky
    I have a Samsung G3 Station 2TB external hard drive (link to PDF specs here). It was working perfectly when I accidentally plugged it in my notebook's power source. The notebook's power source is 19V/3.42A. The hard drive's is 12V/2A and I know that, inside its case, there is regular 2TB SATA drive, along with some sort of adapter. Does this adapter has some kind of power protection? I opened the case and the hard drive board smells bad. Does my data is forever lost or can I replace its board?

    Read the article

  • Can a power failure or forceful shutdown damage hardware?

    - by Vilx-
    Can computer hardware suffer damage from forceful shutdowns (holding the power button for five (5) seconds) or power failures? I believe that normal PC hardware does not suffer from this - after all, it's not much different than what they experience under a standard shutdown. But elsewhere I've read tht another person thought that it could do physical harm to the hard drive and possibly other components as well. He also said that the journaling features of filesystems are useless in face of power failures and were intended to help mitigate damage from system crashes. I think this is nonsense, but then again I lack the experience and knowledge to say it with certainty.

    Read the article

  • How can I guess if a USB cable will power my devices?

    - by rsanchez
    I've had problems with one long (4 meter) USB Mini-B to USB Type-A cable not being able to boot a 2.5'' external hard disc due to not supplying enough current. On top of that, the cable used a Type-A to Mini-B adapter for the Mini-B part, which probably made things worse. Three different shorter cables I got around made the hard disk work without extra current, so it was definitively the cable's fault. However, if I plugged the hard disk to the power, and used the long cable just for data it worked. Here is some related information on powering through USB cables: http://www.girr.org/mac_stuff/usb_stuff.html I have not any long cables that don't have an intermediary Type-A to Mini-B adapter to try them out. My question is: is there a way to guess if a cable will provide enough power for charge/disk drive power? Is it related to the length of the cable, to the build quality of the cable, or the fact that uses intermediary adapters?

    Read the article

  • Power supply issue? New Radeon5850's fan runs at full speed and PC doesn't boot.

    - by Kris
    I recently bought a new ASUS EAH5850 graphics board. I installed it a custom PC which had an ASUS p5n-e SLI mobo along with a 500w Thermaltake W0093RU power supply. Sometimes when doing a cold boot the 5850's fan will run at full speed and the PC will not boot. Powering off by holding down the power button and powering back on sometimes remedies the situation and everything boots normally. Warm reboots also never seem to have problems. For some reason though cold boots almost always do. Another issue I notice is that when the PC does boot normally it takes longer (+30 secs) to POST than with my last video card. I flashed the mobo with the latest available BIOS but it had no effect. Is my problem a power issue or incompatible motherboard or something else I'm missing?

    Read the article

  • Power outage during disk wipe. What do I do now?

    - by Mark Trexler
    I was using Roadkil Diskwipe on an external hard drive and the power went out. I had removed it from any outlet connection by the time power was restored to prevent power-spike damage (it's on a surge protector, but I didn't want to rely on that). My question is, where do I go from here? Obviously I don't care about preserving any data currently on it, I just want to make sure the drive itself is not terminally damaged. I'm running chkdsk (full), but I don't know if that's the correct step to assessing any damage. If it makes any difference, the hard drive was unallocated at the time of the outage, as Diskwipe requires that for it to run. Also, could something like this cause latent problems with the drive itself (i.e. serious issues that I won't be aware of when testing it now). I'd appreciate any program recommendations if chkdsk is not the most appropriate diagnostic route. Thank you.

    Read the article

  • Suspend only works once after full power cycle with ASUS P7P55D-E Pro

    - by John Chadwick
    This one is strange. I can't seem to get suspend working more than once per power cycle. When I say "power cycle," I mean the only way to get one proper suspend is to cut power from the power supply and boot back up cold. After the proper suspend, I get a failed suspend, and after all reboots or cold boots until power is cut, suspends fail. I'm using an ASUS P7P55D-E Pro with a Sandy Bridge Core i7, running on Ubuntu Precise repositories and UEFI. I'm running Nouveau from repository (And Gallium3d compiled from git, but that does not come into this since I can avoid OpenGL and it still happens the same way) with a GTX 285 (nv50.) I had to build a custom kernel (3.3) in order for ACPI 5.0 to be supported and make suspend work at all. I compiled it using the latest Ubuntu kernel's config file with the additional entries set to the default options. All packages are up to date. I know these are relatively exotic settings, but I'm hoping maybe I can get some help anyways. The behavior when suspend fails is strange. Upon a proper suspend, all fans turn off and the only led left on, the power led, is blinking. Upon a failed suspend, 1. USB power remains. 2. The power led stays on solid. 3. All fans seem to still be on. 4. I can hear what I believe is the primary harddrive shutting off. 5. Despite USB power remaining, the USB powered keyboard does not respond to anything, and the indicator leds on it shut off. Pressing the power button does nothing, and of course I have not to date found a way to wake it up. When trouble shooting the first round of issues I got with suspend not too long ago, I ended up building a list of modules to disable upon sleeping. Here's my config file for them: In /etc/pm/config.d/01modules: SUSPEND_MODULES="uhci_hd ehci_hd button" All of my other pm configuration files are stock. In case it's any help, here are my relevant BIOS settings. Thanks.

    Read the article

  • CastClassException on Custom View

    - by tuxGurl
    When I try to findViewById() on my custom view I keep getting a ClassCastException. I've tried so many things that I'm sure I've botched the code now! To make sure I'm not going insane I stripped down the classes to their bare minimum inorder to find what was wrong. I'm new to android programming and I'm sure I'm missing something basic. This is BaseImageView an extended view class. package com.company.product.client.android.gui.views; import android.content.Context; import android.graphics.Canvas; import android.graphics.Color; import android.view.View; public class BaseImageView extends View { public BaseImageView(Context context) { super(context); } @Override protected void onDraw(Canvas canvas) { super.onDraw(canvas); canvas.drawColor(Color.GREEN); } } This is LiveImageView an extension of the BaseImageView class. package com.company.product.client.android.gui.views; import android.content.Context; import android.util.AttributeSet; public class LiveImageView extends BaseImageView { public LiveImageView(Context context, AttributeSet attrs) { super(context); } } Here is the Layout my_view.xml. <LinearLayout xmlns:android="http://schemas.android.com/apk/res/android" android:orientation="vertical" android:layout_width="fill_parent" android:layout_height="fill_parent" android:gravity="center"> <View class="com.company.product.client.android.gui.views.LiveImageView" android:id="@+id/lvImage" android:layout_width="wrap_content" android:layout_height="wrap_content" /> </LinearLayout> And here is the onCreate in my Activity LiveViewActivity. @Override public void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); try { setContentView(R.layout.my_view); final LiveImageView lvImage = (LiveImageView) findViewById(R.id.lvImage); } catch (final Exception e) { Log.e(TAG, "onCreate() Exception: " + e.toString()); e.printStackTrace(); } Finally, this is stack trace. 02-11 17:25:24.829: ERROR/LiveViewActivity(1942): onCreate() Exception: java.lang.ClassCastException: android.view.View 02-11 17:25:24.839: WARN/System.err(1942): java.lang.ClassCastException: android.view.View 02-11 17:25:24.839: WARN/System.err(1942): at com.company.product.client.android.gui.screen.LiveViewActivity.onCreate(LiveViewActivity.java:26) 02-11 17:25:24.839: WARN/System.err(1942): at android.app.Instrumentation.callActivityOnCreate(Instrumentation.java:1047) 02-11 17:25:24.849: WARN/System.err(1942): at android.app.ActivityThread.performLaunchActivity(ActivityThread.java:2459) 02-11 17:25:24.849: WARN/System.err(1942): at android.app.ActivityThread.handleLaunchActivity(ActivityThread.java:2512) 02-11 17:25:24.849: WARN/System.err(1942): at android.app.ActivityThread.access$2200(ActivityThread.java:119) 02-11 17:25:24.849: WARN/System.err(1942): at android.app.ActivityThread$H.handleMessage(ActivityThread.java:1863) 02-11 17:25:24.859: WARN/System.err(1942): at android.os.Handler.dispatchMessage(Handler.java:99) 02-11 17:25:24.859: WARN/System.err(1942): at android.os.Looper.loop(Looper.java:123) 02-11 17:25:24.859: WARN/System.err(1942): at android.app.ActivityThread.main(ActivityThread.java:4363) 02-11 17:25:24.869: WARN/System.err(1942): at java.lang.reflect.Method.invokeNative(Native Method) 02-11 17:25:24.869: WARN/System.err(1942): at java.lang.reflect.Method.invoke(Method.java:521) 02-11 17:25:24.869: WARN/System.err(1942): at com.android.internal.os.ZygoteInit$MethodAndArgsCaller.run(ZygoteInit.java:860) 02-11 17:25:24.869: WARN/System.err(1942): at com.android.internal.os.ZygoteInit.main(ZygoteInit.java:618) 02-11 17:25:24.879: WARN/System.err(1942): at dalvik.system.NativeStart.main(Native Method)

    Read the article

  • Aggregate SharePoint Event/Items into your Calendar view using Calendar Overlay

    - by eJugnoo
    One of the most common features I have seen in common use for SharePoint (prior to 2010) in Intranet environments for Team site is Calendar’s. Not only the Calendar list type, but also the ability to add a Calendar view to any list that has the desired columns to construct a Calendar – such as Start, End, Title etc. While this was all great for a single site/calendar, the problem of having to track numerous calendar’s remained. With introduction of Outlook 2007 bi-directional integration with SharePoint, and particularly the ability of Outlook to overlay calendar helped bridge the gap. Now one could connect to number of team sites, and setup Calendar overlays in Outlook using varying colours, to easily identify event source and yet benefit from the plotting of events on single Calendar view. This was all good, but each user in your Enterprise was supposed to setup in a “pull” fashion. This is good for flexibility, not so good when you need to “push” consistency and productivity (re-use). So, what was missing on SharePoint is the ability to have server-side overlay’s that everyone can see – in a single place, aggregating multiple sources. Until SharePoint 2010 arrived! Calendars Overlay in SharePoint 2010 There are Calendar lists and Calendar views. View can be created for almost all lists, as far as you have desired column’s in a list like Start, End, Title etc. to be able to describe and plot an item in a Calendar format. In SharePoint 2010, create a new Calendar list. Go to Calendar ribbon tab, and click Calendar Overlay. You get the screen with list of existing Overlay’s associated with current Calendar (list – in our case). Click on “New Calendar”… Notice the breadcrumb! You are adding Overlay to existing list (Team Calendar – in our case). You have choice of “pulling” Calendar info from an existing Calendar (list/view) in SharePoint or even from Exchange! Set standard info like a name, description and decide the colour you want for the items in aggregated Calendar overlay. Select the source site/list/view, anywhere in farm. When you select Exchange as source of Calendar, you get option to add OWA and Exchange Web Service url. I will cover details of connecting with Exchange in another post, and focus on Overlay’s with SharePoint for this one. Once you have added a new Calendar overlay to existing Calendar veiw, you get something like below for Day view, Week view, and Month view respectively Notice the Overlay colours: Now, if you decide to connect this Calendar to Outlook to sync the items, it will only sync items from main view, and not from Overlay source. So such Overlay of calendar’s is server-side aggregation only. That increases my curiosity, so I try adding the Calendar list view as a web-part on a new page. As you see, this instance of view didn’t include item from source that we had added to default Calendar view. This is – probably – due to the fact that this is a new web-part view for the page. If you want to add overlay to this one, you have to redo that from Ribbon. This also means, subject to purpose and context you get the flexibility to decide what overlay is suited. Also you can only add 10 Overlay’s to an existing view instance. Conclusion Calendar Overlay is clearly a very useful feature that fills a gap of not being able to aggregate information from multiple sources into a Calendar view within context of current items. Source of items can be existing SharePoint calendar views on any site, or even Exchange (via OWA/Exchange web services). List type for source doesn’t matter, it just need a Calendar view type available. You can have 10 overlays. Overlays are for the specific view only, and are server-side only – which means they do not get synced in Outlook. While you can drag-drop current list items, you cannot edit overlay items as they are read-only within scope of current Calendar view. You can of course click on source Overlay item to edit at the source. I’d like to hear, how you think Overlay’s will help you in your case, or how you are already using them... Enjoy SharePoint! --Sharad

    Read the article

  • Hard Disk Spins Down as long as Battery is in Laptop

    - by Brock Dute
    Hi, I just figured out today that as long as the battery is in my laptop, it doesn't matter if it's fully charged while plugged in, Ubuntu always spins down my hard drive. I noticed this because there was a huge difference in speed when I removed the batteries. My settings for power management is basically: on AC power, don't spin down harddrive, dont suspend or anything on battery power, basically save as much power as possible I assumed that if I plug in my laptop, it'll use the On AC Power settings no matter what but apparently, this isn't so. Is there a way to "fix" this?

    Read the article

  • Power button missing

    - by Christophe De Troyer
    An almost clean install of Ubuntu 13.10 keeps hiding the power button. I noticed before that my clock and power button were missing in the right top corner. I rebooted my system and they were back. Now I see my power button only is missing. How do I go about fixing this? I can't keep rebooting, can I? The latest thing I did was removing Ubuntu One: Removing Ubuntu One I don't think I did something that might've tinkered with these settings though.

    Read the article

  • Sudo Non-Password access to /sys/power/state

    - by John
    On my computer, pm-hibernate appears to be broken, however using the command echo disk > /sys/power/state appears to work perfectly. Now I just need regular user access to it, using sudo. How do I do this? The command sudo echo disk > /sys/power/state simply returns bash: /sys/power/state: Permission denied. Also, I need this in a regularly used script, how can I make it so that I don't have to type in my password for it to work???

    Read the article

< Previous Page | 10 11 12 13 14 15 16 17 18 19 20 21  | Next Page >