Search Results

Search found 4287 results on 172 pages for 'frame'.

Page 140/172 | < Previous Page | 136 137 138 139 140 141 142 143 144 145 146 147  | Next Page >

• Intel NIC X540-T1 non-functional in Ubuntu Server 12.04

  - by Jeff Carr

  I have installed three Intel X540-T1's in servers running Ubuntu Server 12.04, but all are non-functional, no link lights, no packets sent or received, and no connection on ip4 or ip6 whether set up as dhcp or static. Also, dmesg doesn't detect cable connection or disconnection. I updated the default ixgbe driver to Intel's latest version (3.11.33) with no change. The ethernet controller is being reported as X540-AT2 (which might be a problem that I can't figure out how to fix), but the subsystem is X540-T1 so I believe that might be intended. Does anyone have any experience with this that could assist? ifconfig eth2 eth2 Link encap:Ethernet HWaddr a0:36:9f:14:5f:ea inet addr:192.168.101.1 Bcast:192.168.101.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1<br> RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ethtool -i eth2 driver: ixgbe version: 3.11.33 firmware-version: 0x8000037c bus-info: 0000:08:00.0 supports-statistics: yes supports-test: yes supports-eeprom-access: yes supports-register-dump: yes lspci -vvnns 08:00.0 08:00.0 Ethernet controller [0200]: Intel Corporation Ethernet Controller 10 Gigabit X540-AT2 [8086:1528] (rev 01) Subsystem: Intel Corporation Ethernet Converged Network Adapter X540-T1 [8086:0002] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at e8000000 (64-bit, prefetchable) [size=2M] Region 4: Memory at e8200000 (64-bit, prefetchable) [size=16K] [virtual] Expansion ROM at e8280000 [disabled] [size=512K] Capabilities: <access denied> Kernel driver in use: ixgbe Kernel modules: ixgbe

  Read the article

• Change authentication wifi WPA to WEP on Windows 8

  - by Kites

  I use netsh wlan set hostednetwork mode=allow ssid=Kites key=phambaoViet netsh wlan start hostednetwork To share WiFi from LAN network on laptop (Windows 8) to my other device. When I show information netsh wlan show hostednetwork the supported authentication is WPA. My device support authentication WEP only. How can I change the authentication to WEP? Infomation: Interface name: Wi-Fi Driver : Qualcomm Atheros AR9002WB-1NG Wireless Network A dapter Vendor : Qualcomm Atheros Communications Inc. Provider : Microsoft Date : 03/07/2012 Version : 3.0.0.130 INF file : C:\Windows\INF\netathrx.inf Files : 2 total C:\Windows\system32\DRIVERS\athrx.sys C:\Windows\system32\drivers\vwifibus.sys Type : Native Wi-Fi Driver Radio types supported : 802.11b 802.11g 802.11n FIPS 140-2 mode supported : Yes 802.11w Management Frame Protection supported : Yes Hosted network supported : Yes Authentication and cipher supported in infrastructure mode: Open None Open WEP-40bit Open WEP-104bit Open WEP WPA-Enterprise TKIP WPA-Personal TKIP WPA2-Enterprise TKIP WPA2-Personal TKIP Vendor defined TKIP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA-Enterprise CCMP WPA-Personal CCMP WPA2-Enterprise CCMP Vendor defined CCMP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA2-Personal CCMP Vendor defined Vendor defined Authentication and cipher supported in ad-hoc mode: Open None Open WEP-40bit Open WEP-104bit Open WEP WPA2-Personal CCMP Vendor defined Vendor defined

  Read the article

• Natting trafic from a tunnel to internet

  - by mezgani

  I'm trying to set up a GRE tunnel between a linux box and a router (LAN), and I'm having a few problems which seem to depend to my iptables configuration. Watching with tcpdump on linux box, I can see packets coming with flags GREv0, all i need right know is forwarding this data to internet, found here some trace : iptables -F iptables -X iptables -P INPUT ACCEPT iptables -P FORWARD ACCEPT iptables -P OUTPUT ACCEPT iptables -t nat -F iptables -t nat -X iptables -t nat -P PREROUTING ACCEPT iptables -t nat -P POSTROUTING ACCEPT iptables -t nat -P OUTPUT ACCEPT iptables -t mangle -F iptables -t mangle -X iptables -t mangle -P PREROUTING ACCEPT iptables -t mangle -P OUTPUT ACCEPT iptables -A INPUT -p 47 -j ACCEPT iptables -A FORWARD -i ppp0 -o cloud -j ACCEPT iptables -A FORWARD -i cloud -o ppp0 -j ACCEPT iptables -A FORWARD -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -t nat -A POSTROUTING -o ppp0 -j MASQUERADE echo "1" /proc/sys/net/ipv4/ip_forward cloud Link encap:UNSPEC HWaddr C4-CE-7A-2E-F2-BF-DD-C0-00-00-00-00-00-00-00-00 inet adr:10.3.3.3 P-t-P:10.3.3.3 Masque:255.255.255.255 UP POINTOPOINT RUNNING NOARP MTU:1476 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:124 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:0 RX bytes:0 (0.0 B) TX bytes:10416 (10.1 KiB) Table de routage IP du noyau Destination Passerelle Genmask Indic MSS Fenêtre irtt Iface 196.206.120.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.3.3.0 0.0.0.0 255.255.255.0 U 0 0 0 cloud 0.0.0.0 196.206.120.1 0.0.0.0 UG 0 0 0 ppp0 root@aldebaran:~# ip route 196.206.120.1 dev ppp0 proto kernel scope link src 196.206.122.46 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.18 10.3.3.0/24 dev cloud scope link default via 196.206.120.1 dev ppp0

  Read the article

• can't load IA 32-bit .dll on a AMD 64 bit platform

  - by user101425

  I have a Windows 2003 64 bit terminal server which we run a Java application from. The application has always worked up until 2 days ago. No new updates have been installed to the server in that time frame. I have tried re-installing java 64 bit but still have the following error. Unexpected exception: java.lang.reflect.InvocationTargetException java.lang.reflect.InvocationTargetException at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(Unknown Source) at java.lang.reflect.Method.invoke(Unknown Source) at com.sun.javaws.Launcher.executeApplication(Unknown Source) at com.sun.javaws.Launcher.executeMainClass(Unknown Source) at com.sun.javaws.Launcher.doLaunchApp(Unknown Source) at com.sun.javaws.Launcher.run(Unknown Source) at java.lang.Thread.run(Unknown Source) **Caused by: java.lang.UnsatisfiedLinkError: C:\Documents and Settings\administrator\Application Data\Sun\Java\Deployment\cache\6.0\19\625835d3-5826d302-n\swt-win32-3116.dll: Can't load IA 32-bit .dll on a AMD 64-bit platform** at java.lang.ClassLoader$NativeLibrary.load(Native Method) at java.lang.ClassLoader.loadLibrary0(Unknown Source) at java.lang.ClassLoader.loadLibrary(Unknown Source) at java.lang.Runtime.loadLibrary0(Unknown Source) at java.lang.System.loadLibrary(Unknown Source) at org.eclipse.swt.internal.Library.loadLibrary(Library.java:100) at org.eclipse.swt.internal.win32.OS.<clinit>(OS.java:18) at org.eclipse.swt.graphics.Device.init(Device.java:563) at org.eclipse.swt.widgets.Display.init(Display.java:1784) at org.eclipse.swt.graphics.Device.<init>(Device.java:99) at org.eclipse.swt.widgets.Display.<init>(Display.java:363) at org.eclipse.swt.widgets.Display.<init>(Display.java:359) at com.ko.StartKO.main(StartKO.java:57) ... 9 more

  Read the article

• Sound out of sync after merging multiple mp4 files with Avidemux

  - by Goto10

  I am trying to join (merge) two or more .mp4 files together, without re-encoding. Here is what I did: Started Avidemux 2.5.5. With File-Open, selected Input1.mp4. I received this message - "H.264 detected. If the file is using B-frames as reference it can lead to a crash or stuttering. Avidemux can use another mode which is safe but YOU WILL LOOSE SOME FRAME ACCURACY. Do you want to use that mode?". I chose "No". With File-Append, selected Input2.mp4. I received the same "H.264 detected" message again and chose "No". Selected the Format to MP4 (from AVI). Saved the output file (called Output.mp4) with File-Save-Save Video. Unfortunately, when I play the Output.mp4 video in VLC, the sound is out of sync with the second video. How can I correct this?

  Read the article

• Ubuntu second static IP, ifconfig, /etc/network/interfaces

  - by Schmoove

  I would like to add a second static IP to my local Ubuntu 11.10 desktop machine and have it automatically available after rebooting. So far I am successfully using ifconfig to to temporarily set up an alias for my primary network interface: # ifconfig eth1:0 192.168.178.3 up # ifconfig eth1 Link encap:Ethernet HWaddr c8:60:00:ef:a3:d9 inet addr:192.168.178.2 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::ca60:ff:feef:a3d9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:61929 errors:0 dropped:0 overruns:0 frame:0 TX packets:64034 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:45330863 (45.3 MB) TX bytes:28175192 (28.1 MB) Interrupt:42 Base address:0x4000 eth1:0 Link encap:Ethernet HWaddr c8:60:00:ef:a3:d9 inet addr:192.168.178.3 Bcast:192.168.178.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:42 Base address:0x4000 However, when I add the following to /etc/network/interfaces, the alias is not up and running as expected after a reboot: # vi /etc/network/interfaces auto eth1:0 iface eth1:0 inet static address 192.168.178.3 netmask 255.255.255.0 I would like to know what to configure to get this to work. As a side note, I am running gnome shell.

  Read the article

• How does Windows 7 DNS client work?

  - by Mark Allison

  I am using a local DHCP and DNS server on my home network on a linux machine. It is running CentOS 6.3 with dnsmasq 2.48. It's all working fine except for local DNS lookups for Windows machines only. I have a mix of Ubuntu, CentOS and Windows machines on the network, some virtual, some physical. I have a machine called boron and the domain is called localdomain If I ping boron from any linux machine, I get [root@lithium lists]# ping -c3 boron PING boron.localdomain (10.0.0.5) 56(84) bytes of data. 64 bytes from boron.localdomain (10.0.0.5): icmp_seq=1 ttl=64 time=0.740 ms 64 bytes from boron.localdomain (10.0.0.5): icmp_seq=2 ttl=64 time=0.478 ms 64 bytes from boron.localdomain (10.0.0.5): icmp_seq=3 ttl=64 time=0.458 ms --- boron.localdomain ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2000ms rtt min/avg/max/mdev = 0.458/0.558/0.740/0.131 ms If I do it from my Windows 7 machine, I get: Ping request could not find host boron. Please check the name and try again. If I try ping boron.localdomain I get: Pinging boron.localdomain [67.215.65.132] with 32 bytes of data: Reply from 67.215.65.132: bytes=32 time=16ms TTL=57 Reply from 67.215.65.132: bytes=32 time=188ms TTL=57 Reply from 67.215.65.132: bytes=32 time=15ms TTL=57 Reply from 67.215.65.132: bytes=32 time=14ms TTL=57 Ping statistics for 67.215.65.132: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 14ms, Maximum = 188ms, Average = 58ms which is clearly wrong. Why is it going out to the internet? Why can't my windows machine resolve the boron hostname to a FQDN? My Windows machines and linux machines get their network config from DHCP. UPDATE If I do ipconfig /all in Windows, it looks as I would expect: Windows IP Configuration Host Name . . . . . . . . . . . . : lanthanum Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : .localdomain Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : .localdomain Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : 50-E5-49-38-FC-A2 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 10.0.0.57(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 23 August 2012 13:58:45 Lease Expires . . . . . . . . . . : 24 August 2012 07:58:48 Default Gateway . . . . . . . . . : 10.0.0.6 DHCP Server . . . . . . . . . . . : 10.0.0.6 DNS Servers . . . . . . . . . . . : 10.0.0.6 208.67.222.222 208.67.220.220 NetBIOS over Tcpip. . . . . . . . : Enabled When I do an nslookup I get: Server: carbon.localdomain Address: 10.0.0.6 *** carbon.localdomain can't find boron: Unspecified error However if I do ifconfig -a in Linux I get: [root@nitrogen ~]# ifconfig -a eth0 Link encap:Ethernet HWaddr 00:0C:29:AF:EC:2A inet addr:10.0.0.7 Bcast:10.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:187687 errors:0 dropped:0 overruns:0 frame:0 TX packets:5857 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:23910700 (22.8 MiB) TX bytes:712964 (696.2 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:329894 errors:0 dropped:0 overruns:0 frame:0 TX packets:329894 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:67153143 (64.0 MiB) TX bytes:67153143 (64.0 MiB) and nslookup: [root@nitrogen ~]# nslookup boron Server: 10.0.0.6 Address: 10.0.0.6#53 Name: boron Address: 10.0.0.5 Both machines are on the same network using the same DHCP server. UPDATE 2 I thought the issue was resolved but I am getting intermittent DNS resolving issues but only on my Windows 7 machine. All my linux boxes are fine. This is what happens when I ping and nslookup from Windows to a Windows 2008 Server: C:\Users\mark>nslookup magnesium Server: carbon.localdomain Address: 10.0.0.6 Name: magnesium.localdomain Address: 10.0.0.12 C:\Users\mark>ping magnesium Pinging magnesium.localdomain [67.215.65.132] with 32 bytes of data: Reply from 67.215.65.132: bytes=32 time=267ms TTL=57 Reply from 67.215.65.132: bytes=32 time=162ms TTL=57 Reply from 67.215.65.132: bytes=32 time=510ms TTL=57 Reply from 67.215.65.132: bytes=32 time=146ms TTL=57 Ping statistics for 67.215.65.132: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 146ms, Maximum = 510ms, Average = 271ms And from Linux: [root@beryllium ~]# ping -c4 magnesium PING magnesium.localdomain (10.0.0.12) 56(84) bytes of data. 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=1 ttl=128 time=0.176 ms 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=2 ttl=128 time=0.634 ms 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=3 ttl=128 time=0.685 ms 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=4 ttl=128 time=0.263 ms --- magnesium.localdomain ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3002ms rtt min/avg/max/mdev = 0.176/0.439/0.685/0.223 ms [root@beryllium ~]# nslookup magnesium Server: 10.0.0.6 Address: 10.0.0.6#53 Name: magnesium.localdomain Address: 10.0.0.12 UPDATE 3 I stopped the Windows DNS client on my Windows 7 machine with net stop dnscache and it is now working fine. It would be nice to get DNS working with the DNS client on, but I might be OK without it, what do you think?

  Read the article

• SSH sometimes screws up connection when terminal overflows?

  - by SeveQ

  I've got a problem with SSH on a Debian Lenny based server (it's a vHost within a Xen environment, booted on a Xen kernel). I hope someone can help me with this. The SSH connection seems somehow getting screwed up frequently when the terminal overflows (new lines beyond the bottom of the terminal, usually forcing it to scroll). The connection gets lost but not regularly disconnected. It nearly always happens when I do the following: an existing SSH connection gets disconnected (regularly) I order putty to reestablish the connection login-prompt appears at the very bottom of the putty terminal window I enter my login-name, press the enter key I'm asked for the password, I enter it, press the enter key and BOOM! Nothing more happens. I have to reconnect again. So it is reproducable. I'm not totally sure if the connection crashes before or after I enter the password. Furthermore it also happens when there is much text to be displayed (for example when I compile something or do an ls -l on a directory with many entries). Using 'screen', however, helps to reduces the frequency of occurence but doesn't solve the problem completely. It's occurence is independent from which terminal software I use. I mostly use putty but it also happens with other clients. I certainly hope somebody can help me solving this problem. Thanks in advance! //edit: I've just made a Wireshark trace of the ssh connection and there is nothing, I repeat, nothing different between the working and the failing connection (at least aside from frame numbers, ports and times that obviously can't be equal). This leads me to the assumption that the error has to happen on the server's side.

  Read the article

• Recommendations for handling Directory Harvesting spam on Exchange 2003

  - by Aaron Alton

  Our Exchange server is getting slammed with anywhere between 450,000 and 700,000 spam messages per day. We receive about 1700 legitimate messages in the same time frame. Roughly 75% of the spam is directory harvesting. We currently have GFI MailEssentials installed. To it's credit, it's doing a very good job, but the sheer volume of spam that we're receiving, and the number of connections that our exchange server is making is preventing legitimate email from being delivered in a timely manner. GFI is set up to check for directory harvesting at the SMTP level, which I presume intercepts the mail before it hits the Exchange services , or goes through SMSE. This "module" is ordered at the top of the list, so (hopefully) dealing with the harvesting is consuming a minimum amount of server resources and bandwidth. My question is, is there anything I can do to prevent our Exchange server's connection pool from being eaten up by these spam hosts? We had to limit the number of concurrent connections being made by Exchange, because it was consuming all of our bandwidth. Thanks, in advance.

  Read the article

• How do I convert a video to GIF using ffmpeg, with reasonable quality?

  - by Kamil Hismatullin

  I'm converting .flv movie to .gif file with ffmpeg. ffmpeg -i input.flv -ss 00:00:00.000 -pix_fmt rgb24 -r 10 -s 320x240 -t 00:00:10.000 output.gif It works great, but output gif file has a very law quality. Any ideas how can I improve quality of converted gif? Output of command: $ ffmpeg -i input.flv -ss 00:00:00.000 -pix_fmt rgb24 -r 10 -s 320x240 -t 00:00:10.000 output.gif ffmpeg version 0.8.5-6:0.8.5-0ubuntu0.12.10.1, Copyright (c) 2000-2012 the Libav developers built on Jan 24 2013 14:52:53 with gcc 4.7.2 *** THIS PROGRAM IS DEPRECATED *** This program is only provided for compatibility and will be removed in a future release. Please use avconv instead. Input #0, mov,mp4,m4a,3gp,3g2,mj2, from 'input.flv': Metadata: major_brand : mp42 minor_version : 0 compatible_brands: isommp42 creation_time : 2013-02-14 04:00:07 Duration: 00:00:18.85, start: 0.000000, bitrate: 3098 kb/s Stream #0.0(und): Video: h264 (High), yuv420p, 1280x720, 2905 kb/s, 25 fps, 25 tbr, 50 tbn, 50 tbc Metadata: creation_time : 1970-01-01 00:00:00 Stream #0.1(und): Audio: aac, 44100 Hz, stereo, s16, 192 kb/s Metadata: creation_time : 2013-02-14 04:00:07 [buffer @ 0x92a8ea0] w:1280 h:720 pixfmt:yuv420p [scale @ 0x9215100] w:1280 h:720 fmt:yuv420p -> w:320 h:240 fmt:rgb24 flags:0x4 Output #0, gif, to 'output.gif': Metadata: major_brand : mp42 minor_version : 0 compatible_brands: isommp42 creation_time : 2013-02-14 04:00:07 encoder : Lavf53.21.1 Stream #0.0(und): Video: rawvideo, rgb24, 320x240, q=2-31, 200 kb/s, 90k tbn, 10 tbc Metadata: creation_time : 1970-01-01 00:00:00 Stream mapping: Stream #0.0 -> #0.0 Press ctrl-c to stop encoding frame= 101 fps= 32 q=0.0 Lsize= 8686kB time=10.10 bitrate=7045.0kbits/s dup=0 drop=149 video:22725kB audio:0kB global headers:0kB muxing overhead -61.778676% Thanks.

  Read the article

• How can I make Internet Explorer 6 render Web pages like Internet Explorer 11?

  - by gparyani

  Now, I know that this may seem like a bad question in that I can just upgrade to Internet Explorer 8, but I am sticking with IE6 in that IE8 removes valuable features, like the ability to save favorites offline and the fact that a file path turns into a Windows Explorer window and typing a Web address into Windows Explorer changes it into an IE window. I know that Internet Explorer 6 does a really bad job at rendering some pages. I know of the Google Chrome Frame extension that brings Chrome-style rendering into IE, but that will soon be discontinued. So, I tried another thing: I know that C:\Windows\System32\mshtml.dll contains the Trident rendering engine that is used by IE, so I tried something: I first backed up the original file by renaming it on Windows XP to mshtml-old.dll, then I tried to copy in the DLL from a computer running Windows 7 with Internet Explorer 10. I noticed that, after copying, the system had replaced the new DLL with the old one, but left the one I backed up intact. Is there any way I can get the system to not replace the DLL like that so that I can transfer in IE11's mshtml.dll into Windows XP and make IE6 render like IE11? I'm looking for an answer that describes how to tweak my system to make IE6 render like IE11 (or IE10), not one that tells me to upgrade IE or install another browser. I don't care how tedious the method is, just as long as it works.

  Read the article

• Debian/Ubuntu - No network connection

  - by leviathanus

  I have a very weird situation on my Ubuntu 12.04 LTS Server. I can not access (ping) my gateway, although I believe my config is ok - I attach the outputs. Any hints where to look? (I changed the beginning of the IP to something different, just obfuscation) ping 5.9.10.129 PING 5.9.10.129 (5.9.10.129) 56(84) bytes of data. From 5.9.10.129 (5.9.10.129) icmp_seq=2 Destination Host Unreachable From 5.9.10.129 (5.9.10.129) icmp_seq=3 Destination Host Unreachable From 5.9.10.129 (5.9.10.129) icmp_seq=4 Destination Host Unreachable uname -r 3.2.0-29-generic ifconfig eth0 eth0 Link encap:Ethernet HWaddr 3c:97:0e:0e:54:d7 inet addr:5.9.10.142 Bcast:5.9.10.159 Mask:255.255.255.224 inet6 addr: fe80::8e70:5aff:feda:c4ac/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1216 errors:0 dropped:0 overruns:0 frame:0 TX packets:490 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:107470 (107.4 KB) TX bytes:34344 (34.3 KB) Interrupt:17 Memory:d2500000-d2520000 ip route default via 5.9.10.129 dev eth0 metric 100 5.9.10.128/27 via 5.9.10.129 dev eth0 5.9.10.128/27 dev eth0 proto kernel scope link src 5.9.10.142 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 5.9.10.129 0.0.0.0 UG 1000 0 0 eth0 5.9.10.128 5.9.10.129 255.255.255.224 UG 0 0 0 eth0 5.9.10.128 0.0.0.0 255.255.255.224 U 0 0 0 eth0 iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination UPD: Eric, this is how routing information looks on a working server: 0.0.0.0 78.47.198.49 0.0.0.0 UG 100 0 0 eth0 78.47.198.48 78.47.198.49 255.255.255.240 UG 0 0 0 eth0 78.47.198.48 0.0.0.0 255.255.255.240 U 0 0 0 eth0 As I understand it, Hetzner tries to ensure security by this, so I can not take over an IP by changing my MAC. But this is another server, which has another netmask (255.255.255.240) UPD2: BatchyX, on the working server: 78.47.198.49 dev eth0 src 78.47.198.60 cache on the broken: 5.9.10.129 dev eth0 src 5.9.10.142 cache

  Read the article

• Routing subnet over GRE tunnel

  - by eMgz

  Hi, Im trying to configure a GRE over IPSec connection between two subnets. The IPSec tunnel is opened and now I want to add a GRE tunnel over it: ip tunnel add GRE01 mode gre remote 10.244.0.1 local 10.244.245.32 ttl 255 ip link set GRE01 up ip addr add 10.244.248.126 dev GRE01 ip route add 10.244.248.125 dev GRE01 Now I have an interface GRE01 (ifconfig): GRE10 Link encap:UNSPEC HWaddr <h_addr> inet addr:10.244.248.126 P-t-P:10.244.248.126 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MTU:1476 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) And the following routes (ip route list): 10.244.248.125 dev GRE10 scope link <pub_subnet> dev eth0 proto kernel scope link src <pub_ip> default via <pub_gw> dev eth0 metric 100 As a last step, I need now to route my subnet over the tunnel: ip route add 10.245.1.224/28 10.244.248.125 However, I am getting the error Error: either "to" is duplicate, or "10.244.248.125" is a garbage. So, what I didn't understand is why I can't route my subnet over the tunnel, once the only route I have there says that it should route the tunnel IP over the GRE01 interface. Any hint? Thanks.

  Read the article

• Debian can't connect to internet using LAN

  - by tampe125

  I have a headless Raspberry Pi using Debian Wheezy. I have a wifi dongle and if I connect my Raspberry using it, everything works fine: I can connect to the Internet, I can ping, I can update. However, if I get down my wifi and set up the lan interface, I lost my internet connection. I still can connect locally, using my laptop, but the connection doesn't exit (ie ping is not working). Some useful info: cat /etc/network/interfaces auto lo auto eth0 iface eth0 inet static address 192.168.0.105 netmask 255.255.255.0 gateway 192.168.0.1 ping www.google.com (nothing request timed out) ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:a2:b5:20 inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1130 errors:0 dropped:0 overruns:0 frame:0 TX packets:1116 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:97223 (94.9 KiB) TX bytes:146140 (142.7 KiB) ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. ^C --- 192.168.0.1 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18007ms cat /etc/resolv.conf nameserver 8.8.8.8 netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 well, I think that's all... Any ideas?

  Read the article

• Debian can't connect to internet using LAN

  - by tampe125

  I have a headless Raspberry Pi using Debian Wheezy. I have a wifi dongle and if I connect my Raspberry using it, everything works fine: I can connect to the Internet, I can ping, I can update. However, if I get down my wifi and set up the lan interface, I lost my internet connection. I still can connect to it locally, using my laptop, but the connection doesn't exit (ie ping is not working). Some useful info: cat /etc/network/interfaces auto lo auto eth0 iface eth0 inet static address 192.168.0.105 netmask 255.255.255.0 gateway 192.168.0.1 ping www.google.com (nothing request timed out) ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:a2:b5:20 inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1130 errors:0 dropped:0 overruns:0 frame:0 TX packets:1116 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:97223 (94.9 KiB) TX bytes:146140 (142.7 KiB) ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. ^C --- 192.168.0.1 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18007ms cat /etc/resolv.conf nameserver 8.8.8.8 netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 well, I think that's all... Any ideas?

  Read the article

• NTOP gives warnings on startup

  - by FR6

  I just installed ntop 1.4.4 and when I start it, it give me infinite warnings "packet truncated": ... RRD_DEBUG: umask 0066 RRD_DEBUG: DirPerms 0700 THREADMGMT: RRD: Started thread (t2992630672) for data collection THREADMGMT[t2992630672]: RRD: Data collection thread starting [p30923] INIT: Created pid file (/var/run/ntop.pid) THREADMGMT[t3086329552]: ntop RUNSTATE: INITNONROOT(3) Now running as requested user 'nobody' (99:99) Note: Reporting device initally set to 0 [eth0] (merged) THREADMGMT[t3086329552]: ntop RUNSTATE: RUN(4) THREADMGMT[t2982140816]: NPS(1): Started thread for network packet sniffing [eth0] THREADMGMT[t2982140816]: NPS(eth0): pcapDispatch thread starting [p30923] THREADMGMT[t2982140816]: NPS(eth0): pcapDispatch thread running [p30923] THREADMGMT[t3047009168]: SIH: Idle host scan thread running [p30923] THREADMGMT[t3057499024]: SFP: Fingerprint scan thread running [p30923] **WARNING** packet truncated (8814->8232) **WARNING** packet truncated (10274->8232) **WARNING** packet truncated (8814->8232) **WARNING** packet truncated (8814->8232) ... Do I need to configure something? I tried to access the web interface (http://localhost:3000) but it does not work. Note: I'm on CentOS. EDIT: Not sure if it helps but there is my "ifconfig": eth0 Link encap:Ethernet HWaddr 00:16:76:BC:7E:77 inet addr:192.168.0.221 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::216:76ff:febc:7e77/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15496640 errors:0 dropped:0 overruns:0 frame:0 TX packets:19256813 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:836230629 (797.4 MiB) TX bytes:608496148 (580.3 MiB) Memory:dffe0000-e0000000

  Read the article

• Why Wireshark does not recognize this HTTP response?

  - by Alois Mahdal

  I have a trivial CGI script that outputs simple text content. It's written in Perl and using CGI module and it specifies only the most basic headers: print $q->header( -type => 'text/plain', -Content_length => $length, ); print $stuff; There's no apparent issue with functionality, but I'm confused about the fact that Wireshark does not recognize the HTTP response as HTTP--it's marked as TCP. Here is request and response: GET /cgi-bin/memfile/memfile.pl?mbytes=1 HTTP/1.1 Host: 10.6.130.38 User-Agent: Mozilla/5.0 (Windows NT 6.1; WOW64; rv:11.0) Gecko/20100101 Firefox/11.0 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: cs,en-us;q=0.7,en;q=0.3 Accept-Encoding: gzip, deflate Connection: keep-alive HTTP/1.1 200 OK Date: Thu, 05 Apr 2012 18:52:23 GMT Server: Apache/2.2.15 (Win32) mod_ssl/2.2.15 OpenSSL/0.9.8m Content-length: 1048616 Keep-Alive: timeout=5, max=100 Connection: Keep-Alive Content-Type: text/plain; charset=ISO-8859-1 XXXXXXXX... And here is the packet overview (Full packet is here on pastebin) No. Time Source srcp Destination dstp Protocol Info tcp.stream abstime 5 0.112749 10.6.130.38 80 10.6.130.53 48072 TCP [TCP segment of a reassembled PDU] 0 20:52:23.228063 Frame 5: 1514 bytes on wire (12112 bits), 1514 bytes captured (12112 bits) Ethernet II, Src: Dell_97:29:ac (00:1e:4f:97:29:ac), Dst: Dell_3b:fe:70 (00:24:e8:3b:fe:70) Internet Protocol Version 4, Src: 10.6.130.38 (10.6.130.38), Dst: 10.6.130.53 (10.6.130.53) Transmission Control Protocol, Src Port: http (80), Dst Port: 48072 (48072), Seq: 1, Ack: 330, Len: 1460 Now when I see this in Wireshark: there's usual TCP handshake then the GET request shown as HTTP with preview then the next packet contains the response, but is not marked as an HTTP response--just a generic "[TCP segment of a reassembled PDU]", and is not caught by "http.response" filter. Can somebody explain why Wireshark does not recognize it? Is there something wrong with the response?

  Read the article

• Any program to help me check whether an ethernet channel can support full-length VLAN packet?

  - by Jimm Chen

  Sometimes, I have to face such a situation that I need to quickly and explicitly know whether a full length VLAN packet can traverse between two RJ45 ports. Yes, I mean 802.1Q ethernet frame with Etype=81 00 (diagram below). What I can do now is: Get two Windows PCs, for each PC, intall Intel Gigabit NIC and Intel specific driver to create a virtual NIC, with VLAN ID=3 assigned. Then connect the two PCs to each of the two RJ45 port. Finally execute ping to generate a full-length ethernet packet. ping -f -l 1472 <dest-IP> This way, I can be sure that the sent packet has the maximum "IP data payload" of 1500 bytes(8 bytes of ICMP header and 1472 bytes of ICMP data). If the ping gets reply, I know that the ethernet channel support full-length VLAN packet. From my experiment, some home switch or broad band routers(e.g. Linksys WRT54G) does not support full-length VLAN packet switching, so only ping -f -l 1468 succeeds. You see, I have to use an expensive Intel NIC to carry on that test, quite inconvenient. You know, for most laptop today, they do not equip an Intel NIC, and, even it is an Intel NIC, Intel VLAN driver, Intel has limitations on the models on which VLAN driver can be installed. So, my question is: Is there a small program that can let me send a full-length VLAN packet without installing a dedicated VLAN driver? Or better, the program has a stock feature that does the very job for my situation. Windows programs preferred, Linux solution welcome. Simpler the program, the better. Thank you.

  Read the article

• Connect linux server to VPN server via PPTP

  - by wowpatrick

  I'm trying to connect a Linux (Ubuntu 10.04 LST) server to a VPN server via the PPTP client to an VPN server. I configured the PPTP client as said in the documentation. The connection is correctly added as an interface, but somehow the connection dose not work. ping -I ppp0 google.com dose not return anything and traceroute -i ppp0 only shows the first hop, and then displays nothing. Any ideas of what is going wrong? Incorrect routing configuration? ifconfig output for the configured interface: ppp0 Link encap:Point-to-Point Protocol inet addr:xx.x.xxx.xxx P-t-P:10.0.0.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1496 Metric:1 RX packets:415 errors:0 dropped:0 overruns:0 frame:0 TX packets:468 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:31428 (31.4 KB) TX bytes:32394 (32.3 KB) route output Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface xx.x.x.1 * 255.255.255.255 UH 0 0 0 ppp0 xx.xxx.xxx.xx sp.ip 255.255.255.255 UGH 0 0 0 eth1 192.168.3.0 * 255.255.255.0 U 0 0 0 eth2 192.168.2.0 * 255.255.255.0 U 0 0 0 eth1 default sp.ip 0.0.0.0 UG 100 0 0 eth1

  Read the article

• Linux server: Dropped packets

  - by Lars

  I see dropped packets using ifconfig on my eth0 interface: eth0 Link encap:Ethernet HWaddr 00:15:17:0d:03:ca inet addr:10.0.1.2 Bcast:10.0.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:30268348 errors:0 dropped:70721 overruns:0 frame:0 TX packets:133076885 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8699434077 (8.6 GB) TX bytes:194937313025 (194.9 GB) Interrupt:16 Memory:feae0000-feb00000 When i use ethtool -S i dont see anything wrong: NIC statistics: rx_packets: 30267138 tx_packets: 133074510 rx_bytes: 8699356158 tx_bytes: 194934147340 rx_broadcast: 35296 tx_broadcast: 5435 rx_multicast: 0 tx_multicast: 0 rx_errors: 0 tx_errors: 0 tx_dropped: 0 multicast: 0 collisions: 0 rx_length_errors: 0 rx_over_errors: 0 rx_crc_errors: 0 rx_frame_errors: 0 rx_no_buffer_count: 0 rx_missed_errors: 0 tx_aborted_errors: 0 tx_carrier_errors: 0 tx_fifo_errors: 0 tx_heartbeat_errors: 0 tx_window_errors: 0 tx_abort_late_coll: 0 tx_deferred_ok: 0 tx_single_coll_ok: 0 tx_multi_coll_ok: 0 tx_timeout_count: 0 tx_restart_queue: 0 rx_long_length_errors: 0 rx_short_length_errors: 0 rx_align_errors: 0 tx_tcp_seg_good: 5757001 tx_tcp_seg_failed: 0 rx_flow_control_xon: 8649 rx_flow_control_xoff: 62072 tx_flow_control_xon: 0 tx_flow_control_xoff: 0 rx_long_byte_count: 8699356158 rx_csum_offload_good: 30212111 rx_csum_offload_errors: 0 rx_header_split: 10857552 alloc_rx_buff_failed: 0 tx_smbus: 0 rx_smbus: 0 dropped_smbus: 0 rx_dma_failed: 0 tx_dma_failed: 0 I am running Ubuntu 12.04 with kernel 3.2.0-30-generic #48-Ubuntu SMP I have pinged every device on my internal network for about 24 hours, without packet loss. Also checked my router and my interface to the WAN, also no errors there. Does anyone have any clue?

  Read the article

• KeePass lost password and/or corruption due to Dropbox/KeePassX

  - by GummiV

  I started using Keepass about a month ago to hold my passwords and online accounts info. Everything was stored in a single .kdb file, only protected with a password. I'm using Windows 7. Now Keepass can't open my .kdb file with the error "Invalid/wrong key". I'm fairly confident I have the right password. Altough I might have mixed up a few letters I've tried about two dozen different combinations to minimize that possibility - but can't rule it out though. My guess is however that the .kdb file got corrupted, either due to Dropbox syncing (only using it on one computer though) or because I edited the file using KeePassX on Ubuntu (dual boot on the same computer, accessing a mounted Win7 NTFS partition), or possibly a combination of both. I have tried restoring older versions(even the original one) from Dropbox and trying out all possible passwords without any luck. (which does seem to rule out KeePassX as the culprit, since oldest copies are before I edited the file from Ubuntu) I have tried opening the file with the "Repair KeePass Database file" which always gives the "0xA Invalid/corrupt file structure" (the same error for when a wrong password is typed). I was wondering if there was any way for me to salvage my hard-gathered data. I know generally that brute force cracking is not feasible, but since I can remember probably more than half of the usernames/passwords, any maybe the fact that one of them does come up fairly often (my go-to pass for trivial stuff), that might simplify the brute force process to a doable time frame. Maybe the brute-force thing might incorporate the fact that I know the password length and what characters it's made from. (If we assume corruption, not a password-blackout on my part) I could do some programming if there are any libraries or routines that I could use. Other people seem to have had a similar probem http://forums.dropbox.com/topic.php?id=6199 http://forums.dropbox.com/topic.php?id=9139 http://www.keepassx.org/forum/viewtopic.php?t=1967&f=1 So hopefully this question will become a suitible resource for people when searching the web. Feel free to tell me if you think this should rather be a community wiki.

  Read the article

• Acrobat 9 Pro - shortcut key failure

  - by Rick G

  I create numerous Acrobat PDF files from MS Word documents via Acrobat 9 Pro. I often need to print a single page from an Acrobat PDF file. I normally use the keyboard shortcut Control-P (Print Dialog) and ALT-U (current page). I recently set up a new PC with Windows 7, and this shortcut combination does not work. When I press ALT-U, it moves the highlight to the correct item, but does not select the radio button. If I press the Enter key, then I print the entire document instead of the current page - VERY annoying! It looks like there is an error in the design of the Print dialog for Acrobat. There are two items which have ALT-U as the keyboard shortcut. They are "Current page" in the Print range frame, and "Summarize comments". I have been able to use Control-P (Print Dialog) and ALT-U (current page) with no problems on virtual machines and older computers running Windows XP. Maybe I installed some software on the new PC that is messing up the keyboard shortcut. Is there any way to figure out the culprit - or is this a known problem with Acrobat?

  Read the article

• ffmpeg cutting video duration

  - by Steve Spence

  When using ffmpeg on linux, my 4.3GB 2.21 second video is being chopped down to 1.56 duration. I'm trying to reduce file size, but not lose frames. steve@steve-OptiPlex-170L:~/Desktop$ ffmpeg -i microbe.avi microbe.mp4 ffmpeg version 0.8.3-4:0.8.3-0ubuntu0.12.04.1, Copyright (c) 2000-2012 the Libav developers built on Jun 12 2012 16:37:58 with gcc 4.6.3 * THIS PROGRAM IS DEPRECATED * This program is only provided for compatibility and will be removed in a future release. Please use avconv instead. Input #0, avi, from 'microbe.avi': Duration: 00:02:21.80, start: 0.000000, bitrate: 242311 kb/s Stream #0.0: Video: rawvideo, bgr24, 1280x960, 10 tbr, 10 tbn, 10 tbc Incompatible pixel format 'bgr24' for codec 'mpeg4', auto-selecting format 'yuv420p' [buffer @ 0x9f861e0] w:1280 h:960 pixfmt:bgr24 [avsink @ 0x9f86440] auto-inserting filter 'auto-inserted scaler 0' between the filter 'src' and the filter 'out' [scale @ 0x9f7d800] w:1280 h:960 fmt:bgr24 - w:1280 h:960 fmt:yuv420p flags:0x4 Output #0, mp4, to 'microbe.mp4': Metadata: encoder : Lavf53.21.0 Stream #0.0: Video: mpeg4, yuv420p, 1280x960, q=2-31, 200 kb/s, 10 tbn, 10 tbc Stream mapping: Stream #0.0 - #0.0 Press ctrl-c to stop encoding frame= 1164 fps= 6 q=31.0 Lsize= 3775kB time=116.40 bitrate= 265.7kbits/s video:3765kB audio:0kB global headers:0kB muxing overhead 0.272870% steve@steve-OptiPlex-170L:~/Desktop$

  Read the article

• Gifsicle: How to set it to not overwrite the original GIF file if the resulting modified GIF file is larger than the original?

  - by galacticninja

  About Gifsicle: Gifsicle is a command-line tool for creating, editing, and getting information about GIF images and animations. One of its features is (from its website): Optimize your animations! This stores only the changed portion of each frame, and can radically shrink your GIFs. You can also use transparency to make them even smaller. Gifsicle’s optimizer is pretty powerful, and usually reduces animations to within a couple bytes of the best commercial optimizers. I call Gifsicle through this .BAT file in the Right Click - 'Send to' Menu: @echo off :compressFile "C:\Programs\Compression Scripts\gifsicle\bin\gifsicle.exe" --batch -V -O3 %1% echo. echo. SHIFT if exist %1% goto compressFile PAUSE This animated GIF file, however: http://i.minus.com/i7WdodY5Zwot3.gif, when its compression is optimized with Gifsicle with the above commands, results in a larger-filesized GIF file. Gifsicle overwrites the original GIF file with the resulting larger-filesized GIF file. Initial filesize: 7.57 MiB (7,942,886 bytes). After running through the above commands with Gifsicle: 7.64 MiB (8,017,622 bytes). Is there a way to prevent Gifsicle from overwriting the original file if its output file is larger than the original file, while still overwriting the original file if the output file is smaller? Details: OS: Windows 7 Gifsicle version: 1.63, from the binary provided here: http://www.lcdf.org/gifsicle/ Gifsicle manual

  Read the article

• Only tunnel certain applications via OpenVPN

  - by jinjin

  Hi, I've purchased a VPN solution, it works correctly when I have "redirect-gateway def1" in the configuration file (routing all traffic through the VPN). However when I remove that line from the configuration file, I am still able to ping-out of the machine (ping -I tap0), however I cannot ping the IP assigned to the machine (it's a public ip), i get the error: Destination Host Unreachable. I only want to have certain applications sending traffic through the VPN tunnel (eg: ZNC, irssi), all of which i can select which IP they use. However they can't recieve any data, making the tunnel essentially useless to me when disabling redirect-gateway. Any ideas on how to allow specific applications use the tunnel, without of forcing everything to go through it? My configuration file is as follows: dev tap remote #.#.#.# float #.#.#.# port 5129 comp-lzo ifconfig #.#.#.# 255.255.255.128 route-gateway #.#.#.# #redirect-gateway def1 secret key.txt cipher AES-128-CBC The output of ifconfig -a when the tunnel is connected: tap0 Link encap:Ethernet HWaddr 00:ff:47:d3:6d:f3 inet addr:#.#.#.# Bcast:#.#.#.# Mask:255.255.255.255 inet6 addr: <snip> Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:612 errors:0 dropped:0 overruns:0 frame:0 TX packets:35 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:25704 (25.1 KiB) TX bytes:6427 (6.2 KiB) EDIT: the Bcast:#.#.#.# (ifconfig) is different from route-gateway #.#.#.# (openvpn) if that makes any difference.

  Read the article

< Previous Page | 136 137 138 139 140 141 142 143 144 145 146 147  | Next Page >