Search Results

Search found 3942 results on 158 pages for 'stick it to the man'.

Page 140/158 | < Previous Page | 136 137 138 139 140 141 142 143 144 145 146 147  | Next Page >

• Windows 7 x64 installation freezes on new PC build

  - by jhsowter

  Symptoms While attempting to install Windows 7 (64 bit) on my new PC build, it freezes usually at the point where it is expanding the windows image, but has frozen as early as accepting the licence agreement, and as late as just after the first restart. My specs are at the bottom of the post. So far I have tried the following to identify the problem, in rough chronological order: Tried different hard drives with different sata cables. Same symptoms. I later used a different computer to install windows on the same hard drive with no problems. Tried the RAM in different slots, and tried one RAM stick instead of two. Same symptoms. Updated the BIOS to 1.60. Same symptoms. Ran Memtest86+ with RAM in dual channel. It passed about 6 times when I left it running overnight. Used USB to install windows instead of an optical drive. Same symptoms. Change SATA configuration from AHCI to IDE. Same symptoms. Tried various different SATA ports. Same symptoms. Updated BIOS to 1.70. Same symptoms. I saw the RAM did not list my motherboard as being supported even though the motherboard did list the RAM as being supported. So I tried some Kingston DDR3 1333MHz RAM instead. Same symptoms. Other (possibly) pertinent information My CPU idles at about 30 °C. I can't tell what it gets to when it's working. When I installed the CPU, the lever which locks the CPU in place took quite a bit of force to pull down. Now I didn't just yank it down without rechecking the CPU was seated properly about 5 times, but it does seems unusual, and I wonder if the CPU was seated badly if I would see these symptoms? I am out of ideas and don't know how to diagnose any further. I suppose either the motherboard or CPU must be the problem. I am on the verge of taking it to a specialist. The Question How should I proceed from here? Is there anything I can rule out as being the source of the symptoms I am seeing? My Specs CPU: Intel i5 3570k RAM: G.Skill RipjawsX 8GB kit HDD: single 3.5" 500GB SATA or 160GB 2.5" SATA (at different times and sometime together. But no RAID or anything). MB: ASRock Extreme4 Z77 PSU: Silverstone Strider Plus 600W ST60F-P

  Read the article

• radvd is not assigning prefix

  - by Samik

  I'm currently trying to setup IPv6 address auto-configuration with router advertisement daemon (radvd) on a virtual machine running CentOS 6.5. But the eth0 interface is not obtaining that prefix. I've obtained the ULA prefix from here. Contents of /etc/sysctl.conf # Kernel sysctl configuration file for Red Hat Linux # # For binary values, 0 is disabled, 1 is enabled. See sysctl(8) and # sysctl.conf(5) for more details. # Controls IP packet forwarding net.ipv4.ip_forward = 0 net.ipv6.conf.all.forwarding = 1 # Controls source route verification net.ipv4.conf.default.rp_filter = 1 # Do not accept source routing net.ipv4.conf.default.accept_source_route = 0 # Controls the System Request debugging functionality of the kernel kernel.sysrq = 0 # Controls whether core dumps will append the PID to the core filename. # Useful for debugging multi-threaded applications. kernel.core_uses_pid = 1 # Controls the use of TCP syncookies net.ipv4.tcp_syncookies = 1 # Disable netfilter on bridges. net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-call-arptables = 0 # Controls the default maxmimum size of a mesage queue kernel.msgmnb = 65536 # Controls the maximum size of a message, in bytes kernel.msgmax = 65536 # Controls the maximum shared segment size, in bytes kernel.shmmax = 68719476736 # Controls the maximum number of shared memory segments, in pages kernel.shmall = 4294967296 Contents of /etc/radvd.conf # NOTE: there is no such thing as a working "by-default" configuration file. # At least the prefix needs to be specified. Please consult the radvd.conf(5) # man page and/or /usr/share/doc/radvd-*/radvd.conf.example for help. # # interface eth0 { AdvSendAdvert on; MinRtrAdvInterval 3; MaxRtrAdvInterval 10; AdvDefaultPreference low; AdvHomeAgentFlag off; prefix fd8a:8d9d:808f:1::/64 { AdvOnLink on; AdvAutonomous on; AdvRouterAddr on; }; }; Contents of /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 HWADDR=52:54:00:74:d7:46 TYPE=Ethernet UUID=af5db1cb-e809-4098-be1a-5a74dbb767b1 ONBOOT=yes NM_CONTROLLED=no BOOTPROTO=dhcp IPV6INIT=yes IPV6_AUTOCONF=yes I've also enabled radvd at startup through chkconfig. Though I noticed that radvd is starting after interfaces are brought up. I've tried restarting the network service afterwards but still I get the following link-local address only #ip -6 addr show 1: lo: mtu 16436 inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: mtu 1500 qlen 1000 inet6 fe80::5054:ff:fe74:d746/64 scope link valid_lft forever preferred_lft forever Edit: Based on the answer given by Sander Steffann I still need clarification on some points but I'm posting here what worked. Contents of /etc/sysconfig/network NETWORKING=yes HOSTNAME=syslog-ng-server NETWORKING_IPV6=yes IPV6FORWARDING=yes Contents of /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 HWADDR=52:54:00:74:d7:46 TYPE=Ethernet UUID=af5db1cb-e809-4098-be1a-5a74dbb767b1 ONBOOT=yes NM_CONTROLLED=no BOOTPROTO=dhcp IPV6INIT=yes IPV6_AUTOCONF=yes IPV6FORWARDING=no Removed following line from /etc/sysctl.conf net.ipv6.conf.all.forwarding = 1 Contents of /etc/radvd.conf is as previous.

  Read the article

• Clonezilla restore from Samba - no 'restoredisk' option

  - by MT_Head

  I used a CloneZilla LiveCD to back up a couple of Windows machines to a Samba share. Now I'm trying to restore those images, and CloneZilla won't even give me the 'restoredisk' or 'restorepart' options on the menu. I'm guessing that this is because CZ isn't recognizing a valid image... but why? Here's a listing of the folder on the Samba share: -rwxrwxrwx 1 marc users 319 May 31 03:45 blkdev.list -rwxrwxrwx 1 marc users 5307 May 31 04:41 clonezilla-img -rwxrwxrwx 1 marc users 4 May 31 04:31 disk -rwxrwxrwx 1 marc users 16091 May 31 04:31 Info-dmi.txt -rwxrwxrwx 1 marc users 11029 May 31 04:31 Info-lshw.txt -rwxrwxrwx 1 marc users 1502 May 31 04:31 Info-lspci.txt -rwxrwxrwx 1 marc users 170 May 31 04:31 Info-packages.txt -rwxrwxrwx 1 marc users 80 May 31 04:41 Info-saved-by-cmd.txt -rwxrwxrwx 1 marc users 10 May 31 04:31 parts -rwxrwxrwx 1 marc users 2097152000 May 31 04:06 sda1.ntfs-ptcl-img.gz.aa -rwxrwxrwx 1 marc users 247361656 May 31 04:08 sda1.ntfs-ptcl-img.gz.ab -rwxrwxrwx 1 marc users 823182034 May 31 04:31 sda2.ntfs-ptcl-img.gz.aa -rwxrwxrwx 1 marc users 36 May 31 03:45 sda-chs.sf -rwxrwxrwx 1 marc users 31744 May 31 03:45 sda-hidden-data-after-mbr -rwxrwxrwx 1 marc users 512 May 31 03:45 sda-mbr -rwxrwxrwx 1 marc users 315 May 31 03:45 sda-pt.parted -rwxrwxrwx 1 marc users 285 May 31 03:45 sda-pt.parted.compact -rwxrwxrwx 1 marc users 259 May 31 03:45 sda-pt.sf (I've been experimenting with various permissions trying to get this to work; that's why they're currently all "rwxrwxrwx"...) I've got my CZ LiveCD stuck in a (different) machine with a 160GB SATA disk that I'm fine with overwriting; although CZ doesn't show a directory listing, it does show that the correct folder is mounted as /home/partimag. But a moment later, after selecting either Beginner or Expert, I'm only presented with the "savedisk", "saveparts", and "exit" options. What am I doing wrong? I am confident that the initial backup was successful; I can post the log if desired, or any other information that might be germane. Edit: I've copied the contents of the folder onto a 16GB USB stick and set THAT as /home/partimag. Still nothing. What the hell is CZ looking for?

  Read the article

• Stack-based keyboard delay using Logitech MX3100 keyboard

  - by Mark S. Rasmussen

  I've been using a Logitech Cordless Desktop MX3100 keyboard for quite a while. I've never really had any problems, except for the occasional typo. I noticed however that I tended make the typo "Laod" instead of "Load", quite a bit more often than any other typos. As it started to get on my nerves, I decided to do some testing. What I found out was than when I write lowercase "load", I'd never make the typo. All uppercase, or just uppercase L, I'd make the typo quite often. My actual (very scientific) testing is probably best described by showing the output: moatmoatmoat MoatMoatMoat loatloatloat LaotLaotLaot loafloafloaf LaofLaofLaof hoathoathoat HoatHoatHoat hoadhoadhoad HoadHoadHoad lortlortlort LrotLrotLrot What i found out was that whenever shift was depressed, typing an uppercase "L" would induce a significant lag if the next character was an "o", compared to the lag of the any other key: High "o" lag: LoLoLoLoLoLo No "a" lag: LaLaLaLaLaLa No lag for neither "o" nor "a": lolololololo lalalalalala By realizing this I regained a slight bit of sanity as I knew I wasn't coming down with a case of Parkinsons. I was actually typing correctly, the lag just interpreted it wrongly. Now, what really bugs me is that I can't fathom how this is occurring. What I'm actually typing, in physical order, is this: L - o - a - d, and yet, the "a" is output before the "o", even though "o" was pressed before "a". So while the keyboard is processing the "Lo" combo, the "a" gets prioritized and is inserted before the "o" is done processing, resulting in Laod instead of Load. And this only happens when typing "Lo", not when typing lowercase "lo". This problem could stem from the keyboard hardware, the receiver hardware or the keyboard software driver. No matter the fault location however, I can't imagine how this could be implemented as anything but a FIFO queue. A general delay, sure, I could live with that, albeit I'd be irritated. But a lag affecting different keys differently, and even resulting in unpredictable outcome - that just doesn't make any sense. I've solved the problem by just switching to a wired keyboard. I just can't shake it off me though; what kind of bug/error/scenario would result in a case like this? Edit: It's been suggested that I stop drinking Red Bull and stick to water instead. While that may actually help solve the issue, I'm really not looking for a solution as such. I'm more interested in an explanation of how this could happen, as I can't imagine any viable technical solution that could result in this behavior.

  Read the article

• shell script to start multiple Java programs from a directory at boot

  - by zcourts

  I'm not sure if this is the best approach to this, It's my first time doing all of this (including writing shell scripts). OS: Centos My problem: I want to start multiple shell scripts at boot. One of the shell scripts is to start my own services and 3 others are for third party services. The shell script to start my own services will be looking for jar files. I currently have two services (will change), written in Java. All services are named under convention prefix-service-servicename What I've done: I created the following directory structure /home/username/scripts init.sh boot/ boot/startthirdprtyservice1.sh boot/startthirdprtyservice2.sh boot/startthirdprtyservice3.sh boot/startmyservices.sh /home/username/services prefix-lib-libraryname.jar prefix-lib-libraryname.jar prefix-service-servicename.jar prefix-service-servicename.jar prefix-service-servicename.jar In init.sh I have the following: #!/bin/sh #This scripts run all executable scripts in the boot directory at boot #done by adding this script to the file /etc/rc.d/rc.local #nohup #run-parts /home/username/scripts/boot/* #for each file in the boot dir... # ignore the HUP (hangup) signal for s in ./boot/*;do if [ -x $s ]; then echo "Starting $s" nohup $s & fi done echo "Done starting bootup scripts " echo "\n" In the script boot/startmyservices.sh I have #!/bin/sh fnmatch () { case "$2" in $1) return 0 ;; esac ; return 1 ; } ##sub strin to match for SUBSTRING="prefix-service" for s in /home/username/services/*;do if [ -x $s ]; then #match service in the filename , i.e. only services are started if fnmatch "$SUBSTRING" "$s" ; then echo "Starting $s " nohup $s & fi fi done echo "Done starting Services" echo "\n" Finally: Usually you can stick a program in /etc/rc.d/rc.local for it to be run at boot but I don't think this works in this case, or rather I don't know what to put in there I've just learnt how to do this by reading up a bit so I'm not sure its particularly the best thing to do so any advice is appreciated. When I run init.sh nohup.out contains Starting the thirdparty daemon... thirdparty started... .... but nothing from myservices.sh and my Java services aren't running I'm not sure where to start debugging or what could be going wrong. Edit Found some issues and got it to work, used -x instead of -n to check if the string is none zero, needed the sub string check to also be if [[ $s = $SUBSTRING ]] ; then and this last one was just stupid, missing java -jar in front of $s Still unsure of how to get init.sh to run at boot though

  Read the article

• USB mouse disconnecting and reconnecting randomly and often

  - by Marc

  Specs: Q6600, evga 780I sli mobo, 4gig RAM, logitech MX518, windows 7 64bit, evga gtx 260, 650W power supply (single rail) The problem I am having is my mouse will reconnect/disconnect (will even hear the sounds from windows) and the light on the bottom of the mouse will turn off/turn on as it starts working again. It really sucks to be playing a game (and happens on desktop as well) for the mouse to just die out for a few seconds and come back. Sometimes it will not happen for days and other times it will do it 2 or more times within 15 seconds. I have tried two different wired mice, have tried multiple USB ports (on front of computer, back of computer, have also used a USB hub and have also plugged in a card that connects to the USB connectors on the motherboard and adds a few usb ports to the back of the computer, and I also bought a USB 2.0 PCI card and that did not help). Nothing else seems to reconnect like this, my usb keyboard has never once cut out like the mouse does and neither have any of the other devices I have connected (webcam, usb hub, various devices sometimes connected through usb cables, and IR reciever for windows media center remote). I have disconnected all usb devices except for my keyboard and mouse and the problem still occurs. I guess it could be something wrong with my motherboard but since no other devices behave similarly I'm just hoping that it is some kind of driver conflict. Installing logitech's drivers has had no effect. It seemed at first that if I go to device manager and uninstall HID-compliant mouse (that and logitech mx518 are listed) that would fix it but it doesn't seem to work anymore or at least not every time (it keeps reinstalling). I have googled "usb mouse disconnects and reconnects" and it seems to be fairly common but none of those were resolved. To stick some easy steps: It happens with or without the drivers installed It has happened with multiple mice on the same computer Bios is the latest version (P08) Motherboard drivers are the latest version Device manager is listing no problems on any USB devices Happens with every usb port, even addon usb cards Happens when all usb devices aside from mouse and keyboard are unplugged I read that maybe it is an IRQ conflict and I tried to look into that but did not really know what was going on, but didn't see anything obviously wrong. Thanks for any help guys, its driving me crazy!

  Read the article

• I/O intensive MySql server on Amazon AWS

  - by rhossi

  We recently moved from a traditional Data Center to cloud computing on AWS. We are developing a product in partnership with another company, and we need to create a database server for the product we'll release. I have been using Amazon Web Services for the past 3 years, but this is the first time I received a spec with this very specific hardware configuration. I know there are trade-offs and that real hardware will always be faster than virtual machines, and knowing that fact forehand, what would you recommend? 1) Amazon EC2? 2) Amazon RDS? 3) Something else? 4) Forget it baby, stick to the real hardware Here is the hardware requirements This server will be focused on I/O and MySQL for the statistics, memory size and disk space for the images hosting. Server 1 I/O The very main part on this server will be I/O processing, FusionIO cards have proven themselves extremely efficient, this is currently the best you can have in this domain. o Fusion ioDrive2 MLC 365GB (http://www.fusionio.com/load/-media-/1m66wu/docsLibrary/FIO_ioDrive2_Datasheet.pdf) CPU MySQL will use less CPU cores than Apache but it will use them very hard, the E7 family has 30M Cache L3 wichi provide boost performance : o 1x Intel E7-2870 will be ok. Storage SAS will be good enough in terms of performance, especially considering the space required. o RAID 10 of 4 x SAS 10k or 15k for a total available space of 512 GB. Memory o 64 GB minimum is required on this server considering the size of the statistics database. Warning: the statistics database will grow quickly, if possible consider starting with 128 GB directly, it will help. This server will be focused on I/O and MySQL for the statistics, memory size and disk space for the images hosting. Server 2 I/O The very main part on this server will be I/O processing, FusionIO cards have proven themselves extremely efficient, this is currently the best you can have in this domain. o Fusion ioDrive2 MLC 365GB (http://www.fusionio.com/load/-media-/1m66wu/docsLibrary/FIO_ioDrive2_Datasheet.pdf) CPU MySQL will use less CPU cores than Apache but it will use them very hard, the E7 family has 30M Cache L3 wichi provide boost performance : o 1x Intel E7-2870 will be ok. Storage SAS will be good enough in terms of performance, especially considering the space required. o RAID 10 of 4 x SAS 10k or 15k for a total available space of 512 GB. Memory o 64 GB minimum is required on this server considering the size of the statistics database. Warning: the statistics database will grow quickly, if possible consider starting with 128 GB directly, it will help. Thanks in advance. Best,

  Read the article

• Specifying network settings during SLES 11 auto installation

  - by banjer

  I'm setting up an autoinst.xml file for auto-installing SLES 11. I get prompted for the various interface settings per below, but they don't seem to stick once the server reboots. I don't think I have the xml defined correctly. I'm hoping someone has experience with this. <ask-list> <ask> <path>networking,dns,hostname</path> <question>Enter Hostname (server name)</question> <stage>initial</stage> <default>merkin</default> </ask> <ask> <path>networking,interfaces,interface,0,device</path> <question>Enter the primary ethernet device:</question> <stage>initial</stage> <default>eth0</default> </ask> <ask> <path>networking,interfaces,interface,0,ipaddr</path> <question>Enter the primary IP Address:</question> <stage>initial</stage> </ask> <ask> <path>networking,interfaces,interface,0,netmask</path> <question>Enter the Netmask Address:</question> <stage>initial</stage> </ask> <ask> <path>networking,routing,routes,route,0,gateway</path> <question>Enter the primary Gateway Address:</question> <stage>initial</stage> </ask> </ask-list> The first one for hostname seems to be sticking just fine, but the rest do not. As an alternative, is there a way to stop the autoinstall at the section where you configure the network devices so that the user can take over? I was able to show the partition proposal, but not sure how to do the same with the networking setup.

  Read the article

• Best Processor for MediaSmart Server?

  - by Kent Boogaart

  I'm trying to figure out what the best possible processor is that I can stick in my HP MediaSmart server. I'm clueless when it comes to correlating CPUs to motherboards. I suspect it's the socket type I care about, but I worry that there's more to it. CPU-Z gives me (excerpt): Processors Information ------------------------------------------------------------------------- Processor 1 ID = 0 Number of cores 1 (max 1) Number of threads 1 (max 1) Name AMD Sempron LE-1150 Codename Sparta Specification AMD Sempron(tm) Processor LE-1150 Package Socket AM2 (940) CPUID F.F.1 Extended CPUID F.7F Brand ID 1 Core Stepping DH-G1 Technology 65 nm Core Speed 1000.0 MHz Multiplier x FSB 5.0 x 200.0 MHz HT Link speed 800.0 MHz Stock frequency 2000 MHz Instructions sets MMX (+), 3DNow! (+), SSE, SSE2, SSE3, x86-64 L1 Data cache 64 KBytes, 2-way set associative, 64-byte line size L1 Instruction cache 64 KBytes, 2-way set associative, 64-byte line size L2 cache 256 KBytes, 16-way set associative, 64-byte line size FID/VID Control yes Max FID 10.0x Max VID 1.350 V P-State FID 0x2 - VID 0x12 (5.0x - 1.100 V) P-State FID 0xA - VID 0x0C (9.0x - 1.250 V) P-State FID 0xC - VID 0x0A (10.0x - 1.300 V) K8 Thermal sensor yes K8 Revision ID 6.0 Attached device PCI device at bus 0, device 24, function 0 Attached device PCI device at bus 0, device 24, function 1 Attached device PCI device at bus 0, device 24, function 2 Attached device PCI device at bus 0, device 24, function 3 Chipset ------------------------------------------------------------------------- Northbridge SiS 761GX rev. 02 Southbridge SiS 966 rev. 59 Graphic Interface AGP AGP Revision 3.0 AGP Transfer Rate 8x AGP SBA supported, enabled Memory Type DDR2 Memory Size 2048 MBytes Channels Single Memory Frequency 200.0 MHz (CPU/5) CAS# latency (CL) 5.0 RAS# to CAS# delay (tRCD) 5 RAS# Precharge (tRP) 5 Cycle Time (tRAS) 15 Bank Cycle Time (tRC) 21 Command Rate (CR) 1T DMI ------------------------------------------------------------------------- DMI BIOS vendor Phoenix Technologies, LTD version R03 date 05/08/2008 DMI System Information manufacturer HP product MediaSmart Server version unknown serial CN68330DGH UUID A482007B-B0CC7593-DD11736A-407B7067 DMI Baseboard vendor Wistron model SJD4 revision A.0 serial unknown DMI System Enclosure manufacturer HP chassis type Desktop chassis serial unknown DMI Processor manufacturer AMD model AMD Sempron(tm) Processor LE-1150 clock speed 2000.0 MHz FSB speed 200.0 MHz multiplier 10.0x DMI Memory Controller correction 64-bit ECC Max module size 4096 MBytes DMI Memory Module designation A0 size 2048 MBytes (double bank) DMI Memory Module designation A1 DMI Memory Module designation A2 DMI Memory Module designation A3 DMI Port Connector designation PS/2 Mouse (internal) port type Mouse Port connector PS/2 connector PS/2 DMI Port Connector designation USB0 (external) port type USB DMI Physical Memory Array location Motherboard usage System Memory correction None max capacity 16384 MBytes max# of devices 4 DMI Memory Device designation A0 format DIMM type unknown total width 64 bits data width 64 bits size 2048 MBytes DMI Memory Device designation A1 format DIMM type unknown total width 64 bits data width 64 bits DMI Memory Device designation A2 format DIMM type unknown total width 64 bits data width 64 bits DMI Memory Device designation A3 format DIMM type unknown total width 64 bits data width 64 bits How do I figure out what options I have for an upgrade?

  Read the article

• Hylafax / Capi4hylafax: faxgetty does not recognize number of lines

  - by Wrikken

  We've got a T.30 card, 30 working lines on it, but for some reason, if I add more then 30 faxes in the queue at any time (and we're busy enough at peak times that this happens a lot), faxgetty sends faxes to non-existent lines and they appear in the error queue as a 'busy' signal on the line, which results in a lot of failed faxes because the counter of max 3 tries increases rapidly. This is using faxgetty (USE_FAXGETTY="y" in /etc/default/hylafax). I've inherited this thing, so I'm not entirely sure how faxgetty is supposed to know the number of lines. However, if I alter the script to faxmodem (USE_FAXGETTY="n" in /etc/default/hylafax and manually enabling 30 modems), this behavior goes away (new faxes 'wait' for a line to be available before trying to send, so each try / fail is a valid one on a working line, majorly descreasing the amount of failed faxes. However, when researching this almost anyone talks about faxgetty being the preferred, more robust, method, and on top of that for some unexplained reason all FIFO's disappeared for some reason after several errorless hours with faxmodem, forcing a hylafax restart using faxgetty until we figured out why this faxmodem solution failed (which is another question, and somewhat out of scope here). Environment: Debian 2.6.26-2-amd64 capi4hylafax 1:01.03.00.99.svn.300-12 hylafax-client 2:4.4.4-10.1 hylafax-server 2:4.4.4-10.1 Config --hfaxd.conf-- LogFacility: daemon ServerTracing: 0x1ff --hyla.conf-- Host: localhost Verbose: No VRes: 196 TimeZone: local DialRules: "/etc/hylafax/dialrules.europe" --/etc/hylafax/config -- InternationalPrefix: 00 LongDistancePrefix: 0 AreaCode: 99999 CountryCode: 31 DialStringRules: "etc/dialrules.europe" ModemGroup: any:faxCAPI SendFaxCmd: "/usr/bin/wrapc2faxsend" --/etc/hylafax/config.faxCAPI -- SpoolDir: /var/spool/hylafax FaxRcvdCmd: /var/spool/hylafax/bin/faxrcvd PollRcvdCmd: /var/spool/hylafax/bin/pollrcvd FaxReceiveUser: uucp FaxReceiveGroup: dialout LogFile: /var/spool/hylafax/log/capi4hylafax #no, checking this log did not yield anything interesting LogTraceLevel: 4 LogFileMode: 0600 ModemGroup: any:faxCAPI #repeats of faxCAPI2 = faxCAPI30, with of course another devicename/local ident: { HylafaxDeviceName: faxCAPI RecvFileMode: 0600 FAXNumber: ****redacted**** LocalIdentifier: ****some-ident-per-device*** MaxConcurrentRecvs: 0 OutgoingController: 1 OutgoingMSN: SuppressMSN: 0 NumberPrefix: NumberPlusReplacer: "00" UseISDNFaxService: 0 RingingDuration: 0 { Controller: 1 AcceptSpeech: 0 UseDDI: 0 DDIOffset: DDILength: 0 IncomingDDIs: IncomingMSNs: AcceptGlobalCall: 1 } } So in short: How does faxgetty determine the number of lines available? (the man page isn't terribly revealing, and I can't find an appropriate setting in hylafax-config. And how can I get a capi4hylafax/hylafax setup which queues more faxes then lines are available correctly without immediately incrementing the fail count? We will not be receiving any faxes on this machine b.t.w. As I said, I've inherited this thing, so if there are important configuration options I'm not including, please let me know.

  Read the article

• xen-create-image does not create inird or initramfs image and domU does not starts with system image

  - by user219372

  I have Fedora 19 as Dom0. To create image I run # xen-create-image --hostname=debian-wheezy --memory=512Mb --dhcp --size=20Gb --swap=512Mb --dir=/xen --arch=amd64 --dist=wheezy After generation finished I start vm and see: # xl create /etc/xen/debian-wheezy.cfg Parsing config from /etc/xen/debian-wheezy.cfg libxl: error: libxl_dom.c:409:libxl__build_pv: xc_dom_ramdisk_file failed: No such file or directory libxl: error: libxl_create.c:919:domcreate_rebuild_done: cannot (re-)build domain: -3 In the /etc/xen/debian-wheezy.cfg i have # # Kernel + memory size # kernel = '/boot/vmlinuz-3.11.2-201.fc19.x86_64' ramdisk = '/boot/initrd.img-3.11.2-201.fc19.x86_64' and ls -1 /boot/*201* shows /boot/config-3.11.2-201.fc19.x86_64 /boot/initramfs-3.11.2-201.fc19.x86_64.img /boot/System.map-3.11.2-201.fc19.x86_64 /boot/vmlinuz-3.11.2-201.fc19.x86_64 Then if I fix ramdisk directive in .cfg file to /boot/initramfs-3.11.2-201.fc19.x86_64.img vm will start but os inside will not boot. In a tail of xl console I get [ OK ] Reached target Basic System. dracut-initqueue[130]: Warning: Could not boot. dracut-initqueue[130]: Warning: /dev/disk/by-uuid/085883ad-73ca-45cc-8bc5-e6249f869b26 does not exist dracut-initqueue[130]: Warning: /dev/fedora/root does not exist dracut-initqueue[130]: Warning: /dev/fedora/swap does not exist dracut-initqueue[130]: Warning: /dev/mapper/fedora-root does not exist dracut-initqueue[130]: Warning: /dev/mapper/fedora-swap does not exist dracut-initqueue[130]: Warning: /dev/xvda2 does not exist Starting Dracut Emergency Shell... Warning: /dev/disk/by-uuid/085883ad-73ca-45cc-8bc5-e6249f869b26 does not exist Warning: /dev/fedora/root does not exist Warning: /dev/fedora/swap does not exist Warning: /dev/mapper/fedora-root does not exist Warning: /dev/mapper/fedora-swap does not exist Warning: /dev/xvda2 does not exist Generating "/run/initramfs/sosreport.txt" Entering emergency mode. Exit the shell to continue. Type "journalctl" to view system logs. You might want to save "/run/initramfs/sosreport.txt" to a USB stick or /boot after mounting them and attach it to a bug report. dracut:/# .img files in /xen/domains/debian-wheezy exists and listed in disk section of debian-wheezy.cfg So what should i do? Update: I've found that xl does not mount images. In debian-wheezy.cfg I have that: root = '/dev/xvda2 ro' disk = [ 'file:/xen/domains/debian-wheezy/disk.img,xvda2,w', 'file:/xen/domains/debian-wheeze/swap.img,xvda1,w', ] And there is no /dev/xvda* or /dev/sda* or /dev/hda* files in VM.

  Read the article

• Windows cannot find the host name "download.microsoft.com" using DNS

  - by joedotnot

  When trying to download a file found on the Microsoft downloads center that starts with, for example, http://download.microsoft.com/download/6/8/7/(some_GUID)/(some_file_name.ext) i get a timeout with "Internet Explorer cannot display the webpage". More information says: Internet connectivity has been lost. The website is temporarily unavailable. The Domain Name Server (DNS) is not reachable. The Domain Name Server (DNS) does not have a listing for the website's domain. If this is an HTTPS (secure) address, click Tools, click Internet Options, click Advanced, and check to be sure the SSL and TLS protocols are enabled under the security section. Diagnose Connection problems says: Windows cannot find the host name "download.microsoft.com" using DNS Bear with me while i expand on the problem: It all started when i tried to download Windows XP mode for my Windows 7 machine. I went to the virtual PC site, then thru the motions of Windows Genuine Advantage which validated ok, but when it redirects to grab the file just times out with above error. (NB: i also tried with the latest Chrome and Firefox but no use due to the Genuine Advantage stuff, so i decided to stick with IE). I am behind an ADSL2+ modem router connecting via wireless (Win 7 Pro laptop); so i hop over to the desktop connected via ethernet (Vista Business), and same result; begin to think site download.microsoft.com site is down. So i give it a break an read up on EDNS, flushing the cache, hosts file, etc... Try again an hour later on the Win 7 machine, still no go; so i turn off the Win 7 (software) firewall, and lo and behold, i can connect and grab any files from download.microsoft.com; (...nice, so we have a Micro$0ft firewall preventing access to a Micro$0ft website, no wonder my auto-updates kept failing but that's another story). But i still am not happy that the desktop connected via ethernet still cannot get to download.microsoft.com, even though i turned off all firewalls, defenders, anti-virus, etc. What is so special / specific about the url download.microsoft.com, any other site is ok, including www.microsoft.com. Any networking guru know what's REALLY going on, and how can i get the desktop to connect? Ping download.microsoft.com - Ping request could not find host download.microsoft.com. Please check the name and try again. Ping google.com or even www.microsoft.com works gives me an IP address. NB: On the wireless laptop ping download.microsoft.com works, i get xxxx.ms.akamai.net [202.7.177.33].

  Read the article

• Custom built machine has much higher power consumption than expected

  - by foraidt

  I built a machine according to the specs of a computer magazine (c't, Germany). According to the magazine, the power consumption should be at around 10W. I don't want to go into the specifics of the hardware but rather ask for general advice on where to look: I updated the BIOS/UEFI version to the latest version, installed all the recommended drivers and unplugged all hardware that's not necessary to boot into Windows. All that was left is the power supply, mainboard, cpu, cpu cooler and one SSD drive. But still I measured a power consumption of 50W, which is 40W more than it should be. I tried booting Linux Mint from a USB stick, so I don't think it's some Windows-related problem.. Where else could I look? Update 1 I dind't want the question to get closed for being too localized but if more details are necessary, here they are: The system is a desktop PC. The power consumption is measured using a Brennenstuhl PM 231 device, which was tested also by c't and they found it quite accurate. The PSU is an Enermax ETL300AWT, the mainboard Intel DH87RL (Socket 1150) and the CPU Intel G3220 (Haswell). Update 2 There is no online version of the article*. The most details I found can be read on its project page (in German, though...) (*)You can pay for downloadable PDFs, however. English translation of that project page Update 3 Regarding the sceptics: It may sound ridiculous but apparently 10W idle consumption is possible with Intel's Haswell architecture. As a kind of proof, there's an additional Blog article explicitly listing the steps needed to reduce the idle consumption to 10W. Additional hardware: I measured the consumption without the HDD, and as expected the usage dropped by around 10W. I have no chassis fans and the CPU fan is a "Scythe Mugen 4" model. It runs at around 600rpm so I think it won't draw much. When stripping off all my extra components I should be at 10W. But I'm not getting anywhere near that. I would be happy to see "just" 15W in the stripped down version but currently I'm not getting below 50W no matter which component I remove. As I see it this cannot be explained by the PSU being less efficient at lower consumption. I also waited half an hour or so (also checked that no Windows updates were running in the background) and the consumption dind't drop by more than a few watts.

  Read the article

• Compiling PHP with GD crashes with EXC_BREAKPOINT (SIGTRAP) on PPC Mac

  - by Ömer

  First of all, I should say that I have searched the whole Internet for this problem but I couldn't find any solution yet. I have a Mac mini PowerPC (PPC) and I run Apache webserver (httpd-2.2.22) with PHP (5.4.0) and I do all the configure & compilation jobs by myself. If configure with: './configure' '--prefix=/usr/local/php5' '--mandir=/usr/share/man' '--infodir=/usr/share/info' '--sysconfdir=/etc' '--with-config-file-path=/etc' '--with-zlib' '--with-zlib-dir=/usr' '--with-openssl=/usr' '--without-iconv' '--enable-exif' '--enable-ftp' '--enable-mbstring' '--enable-mbregex' '--enable-sockets' '--with-mysql=/usr/local/mysql' '--with-pdo-mysql=/usr/local/mysql' '--with-mysqli=/usr/local/mysql/bin/mysql_config' '--with-apxs2=/usr/local/apache2/bin/apxs' '--with-mcrypt' then the PHP works flawlessly. But if I add the GD module by adding these to the script above: '--with-gd' '--with-jpeg-dir=/usr/local/lib' '--with-freetype-dir=/usr/X11R6' '--with-png-dir=/usr/X11R6' '--with-xpm-dir=/usr/X11R6' the PHP gets configured and compiled without any errors but it causes EXC_BREAKPOINT (SIGTRAP) (see the Crash Reporter log below) when I request a page which calls PHP module. It's obvious that something related to the GD module is causing this, probably FreeType module because it's present in the log but it may not be definite of course. When the PHP crashes (or more accurately, httpd) the CPU goes 100% for 10 to 15 seconds until it recovers. I need to use the GD module and keep the Mac mini PowerPC. So, what should I do to solve this problem? Process: httpd [79852] Path: /usr/local/apache2/bin/httpd Identifier: httpd Version: ??? (???) Code Type: PPC (Native) Parent Process: httpd [79846] Date/Time: 2013-11-04 15:44:28.444 +0200 OS Version: Mac OS X 10.5.8 (9L31a) Report Version: 6 Anonymous UUID: 0178B7F8-2241-43F7-A651-9E7234D41A37 Exception Type: EXC_BREAKPOINT (SIGTRAP) Exception Codes: 0x0000000000000001, 0x0000000093c11e0c Crashed Thread: 0 Application Specific Information: *** single-threaded process forked *** Thread 0 Crashed: 0 com.apple.CoreFoundation 0x93c11e0c __CFRunLoopFindMode + 328 1 com.apple.CoreFoundation 0x93c13d88 CFRunLoopAddSource + 276 2 com.apple.DiskArbitration 0x901a6e8c DAApprovalSessionScheduleWithRunLoop + 52 3 ...ple.CoreServices.CarbonCore 0x9512e67c _FSGetDiskArbSession(__DASession**, __DAApprovalSession**) + 540 4 ...ple.CoreServices.CarbonCore 0x9512e420 CreateDiskArbDiskForMountPath(char const*) + 84 5 ...ple.CoreServices.CarbonCore 0x9512d2c8 FSCacheableClient_GetVolumeCachedInfo(char const*, statfs const*, CachedVolumeInfo*, __DADisk*, __DADisk**) + 280 6 ...ple.CoreServices.CarbonCore 0x9512cca4 MountVolume(char const*, statfs*, unsigned char, unsigned char, __DADisk*, short*) + 352 7 ...ple.CoreServices.CarbonCore 0x9512ca48 MountInitialVolumes() + 172 8 ...ple.CoreServices.CarbonCore 0x9512c4d4 INIT_FileManager() + 164 9 ...ple.CoreServices.CarbonCore 0x9512c390 GetRetainedVolFSVCBByVolumeID(unsigned long) + 48 10 ...ple.CoreServices.CarbonCore 0x9512adf4 PathGetObjectInfo(char const*, unsigned long, unsigned long, VolumeInfo**, unsigned long*, unsigned long*, char*, unsigned long*, unsigned char*) + 184 11 ...ple.CoreServices.CarbonCore 0x9512acc4 FSPathMakeRefInternal(unsigned char const*, unsigned long, unsigned long, FSRef*, unsigned char*) + 64 12 libfreetype.6.dylib 0x0070a0fc FT_New_Face_From_Resource + 56 13 libfreetype.6.dylib 0x0070a3b0 FT_New_Face + 48 14 libphp5.so 0x0118d1a8 fontFetch + 824 15 libphp5.so 0x0118edac php_gd_gdCacheGet + 220 16 libphp5.so 0x0118d6d8 php_gd_gdImageStringFTEx + 360 17 libphp5.so 0x011763c0 php_imagettftext_common + 1504 18 libphp5.so 0x01176494 zif_imagefttext + 20 19 libphp5.so 0x014b9c68 zend_do_fcall_common_helper_SPEC + 1048 20 libphp5.so 0x01452898 _ZEND_DO_FCALL_SPEC_CONST_HANDLER + 440 21 libphp5.so 0x014ba878 execute + 776 22 libphp5.so 0x013f190c zend_execute_scripts + 316 23 libphp5.so 0x013779f4 php_execute_script + 596 24 libphp5.so 0x014bbe64 php_handler + 1972 25 httpd 0x000020c0 ap_run_handler + 96 26 httpd 0x00006ae0 ap_invoke_handler + 224 27 httpd 0x000305c4 ap_process_request + 116 28 httpd 0x0002c768 ap_process_http_connection + 104 29 httpd 0x00012d30 ap_run_process_connection + 96 30 httpd 0x00012ecc ap_process_connection + 92 31 httpd 0x000373e4 child_main + 1220 32 httpd 0x000376a8 make_child + 296 33 httpd 0x000377e4 startup_children + 100 34 httpd 0x000387d4 ap_mpm_run + 3988 35 httpd 0x0000a320 main + 3280 36 httpd 0x000019c0 start + 64

  Read the article

• CUPS Web Admin Error 500 Unknown

  - by Floyd Resler

  I keep getting a 500 Unknown error whenever I navigate off the home page of my CUPS web admin. I'm sure I have something misconfigured but I'm not sure what. Here's my configuration: # # "$Id: cupsd.conf.in 8805 2009-08-31 16:34:06Z mike $" # # Sample configuration file for the CUPS scheduler. See "man cupsd.conf" for a # complete description of this file. # # Log general information in error_log - change "warn" to "debug" # for troubleshooting... LogLevel warn # Administrator user group... SystemGroup lpadmin sys root # Only listen for connections from the local machine. Listen 192.168.6.101:631 Listen /var/run/cups/cups.sock ServerName 192.168.6.101 # Show shared printers on the local network. Browsing On BrowseOrder allow,deny BrowseAllow all BrowseLocalProtocols CUPS BrowseAddress 192.168.6.255 # Default authentication type, when authentication is required... DefaultAuthType Basic # Restrict access to the server... Order allow,deny Allow From All Allow From 127.0.0.1 # Restrict access to the admin pages... AuthType Default Require user @SYSTEM Order allow,deny Allow From All Allow From 127.0.0.1 # Restrict access to configuration files... AuthType Default Require user @SYSTEM Order allow,deny Allow From All Allow From 127.0.0.1 # Set the default printer/job policies... # Job-related operations must be done by the owner or an administrator... Require user @OWNER @SYSTEM Order deny,allow # All administration operations require an administrator to authenticate... AuthType Default Require user @SYSTEM Order deny,allow # All printer operations require a printer operator to authenticate... AuthType Default Require user @SYSTEM Order deny,allow # Only the owner or an administrator can cancel or authenticate a job... Require user @OWNER @SYSTEM Order deny,allow Order deny,allow # Set the authenticated printer/job policies... # Job-related operations must be done by the owner or an administrator... AuthType Default Order deny,allow AuthType Default Require user @OWNER @SYSTEM Order deny,allow # All administration operations require an administrator to authenticate... AuthType Default Require user @SYSTEM Order deny,allow # All printer operations require a printer operator to authenticate... AuthType Default Require user @SYSTEM Order deny,allow # Only the owner or an administrator can cancel or authenticate a job... AuthType Default Require user @OWNER @SYSTEM Order deny,allow Order deny,allow # # End of "$Id: cupsd.conf.in 8805 2009-08-31 16:34:06Z mike $". #

  Read the article

• 502 Bad Gateway with nginx + apache + subversion + ssl (SVN COPY)

  - by theplatz

  I've asked this on stackoverflow, but it may be better suited for serverfault... I'm having a problem running Apache + Subversion with SSL behind an Nginx proxy and I'm hoping someone might have the answer. I've scoured google for hours looking for the answer to my problem and can't seem to figure it out. What I'm seeing are "502 (Bad Gateway)" errors when trying to MOVE or COPY using subversion; however, checkouts and commits work fine. Here are the relevant parts (I think) of the nginx and apache config files in question: Nginx upstream subversion_hosts { server 127.0.0.1:80; } server { listen x.x.x.x:80; server_name hostname; access_log /srv/log/nginx/http.access_log main; error_log /srv/log/nginx/http.error_log info; # redirect all requests to https rewrite ^/(.*)$ https://hostname/$1 redirect; } # HTTPS server server { listen x.x.x.x:443; server_name hostname; passenger_enabled on; root /path/to/rails/root; access_log /srv/log/nginx/ssl.access_log main; error_log /srv/log/nginx/ssl.error_log info; ssl on; ssl_certificate server.crt; ssl_certificate_key server.key; add_header Front-End-Https on; location /svn { proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; set $fixed_destination $http_destination; if ( $http_destination ~* ^https(.*)$ ) { set $fixed_destination http$1; } proxy_set_header Destination $fixed_destination; proxy_pass http://subversion_hosts; } } Apache Listen 127.0.0.1:80 <VirtualHost *:80> # in order to support COPY and MOVE, etc - over https (443), # ServerName _must_ be the same as the nginx servername # http://trac.edgewall.org/wiki/TracNginxRecipe ServerName hostname UseCanonicalName on <Location /svn> DAV svn SVNParentPath "/srv/svn" Order deny,allow Deny from all Satisfy any # Some config omitted ... </Location> ErrorLog /var/log/apache2/subversion_error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/subversion_access.log combined </VirtualHost> From what I could tell while researching this problem, the server name has to match on both the apache server as well as the nginx server, which I've done. Additionally, this problem seems to stick around even if I change the configuration to use http only.

  Read the article

• Postfix flow/hook reference, or high-level overview?

  - by threecheeseopera

  The Postfix MTA consists of several components/services that work together to perform the different stages of delivery and receipt of mail; these include the smtp daemon, the pickup and cleanup processes, the queue manager, the smtp service, pipe/spawn/virtual/rewrite ... and others (including the possibility of custom components). Postfix also provides several types of hooks that allow it to integrate with external software, such as policy servers, filters, bounce handlers, loggers, and authentication mechanisms; these hooks can be connected to different components/stages of the delivery process, and can communicate via (at least) IPC, network, database, several types of flat files, or a predefined protocol (e.g. milter). An old and very limited example of this is shown at this page. My question: Does anyone have access to a resource that describes these hooks, the components/delivery stages that the hook can interact with, and the supported communication methods? Or, more likely, documentation of the various Postfix components and the hooks/methods that they support? For example: Given the requirement "if the recipient primary MX server matches 'shadysmtpd', check the recipient address against a list; if there is a match, terminate the SMTP connection without notice". My software would need to 1) integrate into the proper part of the SMTP process, 2) use some method to perform the address check (TCP map server? regular expressions? mysql?), and 3) implement the required action (connection termination). Additionally, there will probably be several methods to accomplish this, and another requirement would be to find that which best fits (ex: a network server might be faster than a flat-file lookup; or, if a large volume of mail might be affected by this check, it should be performed as early in the mail process as possible). Real-world example: The apolicy policy server (performs checks on addresses according to user-defined rules) is designed as a standalone TCP server that hooks into Postfix inside the smtpd component via the directive 'check_policy_service inet:127.0.0.1:10001' in the 'smtpd_client_restrictions' configuration option. This means that, when Postfix first receives an item of mail to be delivered, it will create a TCP connection to the policy server address:port for the purpose of determining if the client is allowed to send mail from this server (in addition to whatever other restrictions / restriction lookup methods are defined in that option); the proper action will be taken based on the server's response. Notes: 1)The Postfix architecture page describes some of this information in ascii art; what I am hoping for is distilled, condensed, reference material. 2) Please correct me if I am wrong on any level; there is a mountain of material, and I am just one man ;) Thanks!

  Read the article

• Looking for a NTP Server Software for Windows

  - by Simon

  I'm looking for a, preferably free, NTP Server for Windows Server 2003/2008. We have already tried the built in Windows Time Server, but our tests did show that it is not very accurate, we see time differences up to 500ms. The max time difference we can allow for our application is ~100ms. Now we have already used the Meinberg NTPd for Windows. It works great except we have one big issue with it: If there is a network connection problem between the client and server, the ntp server is in a panic state It won't give the client a new time until we restart the ntp service. This is a big issue which has caused us some trouble. It was working fine for months until there was a network problem we didn't notice, we only noticed it after a week when the time difference was already 30 sec. on the clients. So please suggest some alternative NTP Server for windows. I did Google but I get a lot of unrelated search results. Edit: So far the ntpd windows version was very accurate and I'd like to stick with it. The only problem is the "panic state" after a network disconnect. Maybe some knows here what the cause of this is and how to fix it. Also, I forgot to mention that we have a server/client setup like this: Server1 -- Server2 -- Server3 -- Client1 -- Client2 -- Client3 So Server2 gets its time from Server1, Server3 gets its time from Server2, and the Clients get their time from Server3. Also, there are clients connected directly to Server2. It is important that all Servers and Clients have the exact same time (within ~100ms) Now there was a network problem with Server3 and its clients. The servers run the ntpd port for Windows, which acts as NTP server and client. The clients have Dimension4 as NTP client. After the network problem, the error message in D4 was something like this (out the top of my head, don't have the exact error message): Server response: The server is in a panic state (could not sync clock) I read through the ntpd docs, and the only mention of "panic" is when the time difference is 10000 seconds which will cause to exit the ntpd server but this was not the case. Also there is a "-g" command line switch to disable the panic exit, but it is already set by default. Any ideas what could cause the panic state and how to get rid of it next time?

  Read the article

• Hard freeze on new computer

  - by mphair

  OCZ Gold 3x2GB 240-Pin DDR3 SDRAM PC312800 Palit NE5T240SFHD01 GeForce GT240 1GB 128-bit GDDR5 ASUS P7P55D-E LGA 1156 P55 SATA 6Gb/s USB 3.0 ATX Intel Motherboard Intel Core i7-860 Lynnfield 2.8GHz 8MB L3 Cache LGA 1156 95W Quad-Core Processor SAMSUNG 22X Optical drive (DVD+-R/RW) CORSAIR CMPSU-620HX 620W ATX12V V2.2 Windows 7 Ultimate x64 Brand new system (got it from newegg two days ago) and it booted up and installed windows and ran for a day just fine. Yesterday, I boot it up in the afternoon and run various games at full graphics for most of the day. I turn on WoW and play for a few hours and it hard stalls. No numlock switching, no mouse feedback but nothing going wrong on the screen. No BSOD. I wait a bit to see if the stall is just a temporary one, but then force shutdown the computer. Upon reboot, everything seems fine, windows sees that it didn't shut down properly but I go into normal boot and restart WoW. I'm able to load it up and start running around when it freezes again. This time when I restart, it doesn't even get to BIOS. It starts (power goes on) and it just hangs with no output to the monitors. I shut it off and went to bed. This morning, I turned it on and went into BIOS setup. I'm not terribly experienced with messing with BIOS settings but I checked over them the best I could. Everything seems fine so I boot into windows and browse the internet for a bit looking for a solution, hard freeze within 10 minutes. I restart and go into BIOS and check the CPU temperature, 40c. I'm kinda stumped here. Some people say it might be a memory issue, but why would it take so long for it to come up? Could it have been slowly accessing one memory stick at a time and then it just got to a bad one and that's what is causing it to fail? It seems odd that I don't get a BSOD from a hardware failure. Having the screen just halt with no input or output change seems like a software thing to me. Any thoughts?

  Read the article

• filtering itunes library items by file location

  - by Cawas

  3 answers and unfortunately no solution yet. The Problem I've got way more than 1000 duplicated items in my iTunes Library pointing to a non-existant place (the "where" under "get info" window), along with other duplicated items and other MIAs (Missing In Action). Is there any simple way to just delete all of them and only them? From the library, of course. By that I mean some MIAs are pointing to /Volumes while some are pointing to .../music/Music/... or just .../music/.... I want to delete all pointing to /Volumes as to later I'll recover the rest. Check the image below. Some Background I tried searching for a specific key word on the path and creating smart play list, but with no result. Being able to just sort all library by path would be a perfect solution! I believe old iTunes could do that. PowerTunes can do it (sort by path) but I can't do anything with its list. I would also welcome any program able to handle this, then import and properly export back the iTunes library. Since this seems to just not be clear enough... AppleScript doesn't work That's because AppleScript just can't gather the missing info anywhere in iTunes Library. Maybe we could use AppleScript by opening the XML file, but that's a whole nother issue. Here's a quote from my conversation with Doug the man himself Adams last december: I don't think you do understand. There is no way to get the path to the file of a dead track because iTunes has "forgotten" it. That is, by definition, what a dead track is. Doug On Dec 21, 2010, at 7:08 AM, Caue Rego wrote: yes I understand that and have seem the script. but I'm not looking for the file. just the old broken path reference to it. Sent from my iPhone On 21/12/2010, at 10:00, Doug Adams wrote: You cannot locate missing files of dead tracks because, by definition, a dead track is one that doesn't have any file information. If you look at "Super Remove Dead Tracks", you will notice it looks for tracks that have "missing value" for the location property.

  Read the article

• load-causing processes disappearing from "top" ps -o pcpu shows bogus numbers

  - by Alec Matusis

  I administer a large number of servers, and I have this problem only with Ubuntu 10.04 LTS: I run a server under normal load (say load average 3.0 on an 8-core server). The "top" command shows processes taking certain % of CPU that cause this load average: say PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 11008 mysql 20 0 25.9g 22g 5496 S 67 76.0 643539:38 mysqld ps -o pcpu,pid -p11008 %CPU PID 53.1 11008 , everything is consistent. The all of the sudden, the process causing the load average disappears from "top", but the process continues to run normally (albeit with a slight performance decrease), and the system load average becomes somewhat higher. The output of ps -o pcpu becomes bogus: # ps -o pcpu,pid -p11008 %CPU PID 317910278 1587 This happened to at least 5 different severs (different brand new IBM System X hardware), each running different software: one httpd 2.2, one mysqld 5.1, and one Twisted Python TCP servers. Each time the kernel was between 2.6.32-32-server and 2.6.32-40-server. I updated some machines to 2.6.32-41-server, and it has not happened on those yet, but the bug is rare (once every 60 days or so). This is from an affected machine: top - 10:39:06 up 73 days, 17:57, 3 users, load average: 6.62, 5.60, 5.34 Tasks: 207 total, 2 running, 205 sleeping, 0 stopped, 0 zombie Cpu(s): 11.4%us, 18.0%sy, 0.0%ni, 66.3%id, 4.3%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 74341464k total, 71985004k used, 2356460k free, 236456k buffers Swap: 3906552k total, 328k used, 3906224k free, 24838212k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 805 root 20 0 0 0 0 S 3 0.0 1493:09 fct0-worker 982 root 20 0 0 0 0 S 1 0.0 111:35.05 fioa-data-groom 914 root 20 0 0 0 0 S 0 0.0 884:42.71 fct1-worker 1068 root 20 0 19364 1496 1060 R 0 0.0 0:00.02 top Nothing causing high load is showing on top, but I have two highly loaded mysqld instances on it, that suddenly show crazy %CPU: #ps -o pcpu,pid,cmd -p1587 %CPU PID CMD 317713124 1587 /nail/encap/mysql-5.1.60/libexec/mysqld and #ps -o pcpu,pid,cmd -p1624 %CPU PID CMD 2802 1624 /nail/encap/mysql-5.1.60/libexec/mysqld Here are the numbers from # cat /proc/1587/stat 1587 (mysqld) S 1212 1088 1088 0 -1 4202752 14307313 0 162 0 85773299069 4611685932654088833 0 0 20 0 52 0 3549 27255418880 5483524 18446744073709551615 4194304 11111617 140733749236976 140733749235984 8858659 0 552967 4102 26345 18446744073709551615 0 0 17 5 0 0 0 0 0 the 14th and 15th numbers according to man proc are supposed to be utime %lu Amount of time that this process has been scheduled in user mode, measured in clock ticks (divide by sysconf(_SC_CLK_TCK). This includes guest time, guest_time (time spent running a virtual CPU, see below), so that applications that are not aware of the guest time field do not lose that time from their calculations. stime %lu Amount of time that this process has been scheduled in kernel mode, measured in clock ticks (divide by sysconf(_SC_CLK_TCK). On a normal server, these numbers are advancing, every time I check the /proc/PID/stat. On a buggy server, these numbers are stuck at a ridiculously high value like 4611685932654088833, and it's not changing. Has anyone encountered this bug?

  Read the article

• IIS httpTracing setting has no effect

  - by digahill

  I'm trying to troubleshoot some performance issues we are having on a specific ASP.NET page with Microsoft's Perfecto Tool on IIS 7.5. Perfecto uses the ETW hooks build in to IIS to report on specific HTTP request, and is working quite well. However, I only want IIS to emit traces for one specific page, say "Default.aspx" in my TestApp Web Application. Following the instructions on the httpTracing man page, I should be able to add the traceUrls element to my root web.config file for TestApp. This doesn't seem to affect tracing whatsoever when I do so. For example, I've used the following settings in the web.config file and every request that hits the IIS server is sending tracing messages that are in turn picked up by Perfecto. (In the System.WebServer section) <httpTracing> <traceUrls> <add value="/Default.aspx" /> </traceUrls> </httpTracing> I then found that the applicationHost.config file on the server had an empty element. I tried removing this element, as well as the httpTracing element in the web.config. After a machine reboot, I was still getting tracing messages! My understanding is that the presense of the httpTracing element is what controlls whether ETW tracing is on or not. I ensured there was no reference to httpTracing in the machine.config, too. At a loss, I decided to remove the IIS Tracing feature with Server Manager. After a reboot, I no longer got ETW tracing. I then reinstalled IIS Tracing feature with Server Manager. As expected, the httpTracing element reappeared in the applicationhost.config file. Tracing messages began sending again for all sites and pages. I then tried to use the traceUrls element at the applicationhost.config level. This also didn't filter out and traces. I must be misunderstanting something key with how httpTracing works. There aren't many resources on the web to help me, either. Can anyone tell me if what I'm trying should work? Has anyone else had success filtering tracing message per page with traceUrls? I should note that I also tried changing with the following setting in applicationhost.config to "allow". It didn't seem to help. <section name="httpTracing" overrideModeDefault="Allow" />

  Read the article

• unable to install anything on ubuntu 9.10 with aptitude

  - by Srisa

  Hello, Earlier i could install software by using the 'sudo aptitude install ' command. Today when i tried to install rkhunter i am getting errors. It is not just rkhunter, i am not able to install anything. Here is the text output: user@server:~$ sudo aptitude install rkhunter ................ ................ 20% [3 rkhunter 947/271kB 0%] Get:4 http://archive.ubuntu.com karmic/universe unhide 20080519-4 [832kB] 40% [4 unhide 2955/832kB 0%] 100% [Working] Fetched 1394kB in 1s (825kB/s) Preconfiguring packages ... Selecting previously deselected package lsof. (Reading database ... ................ (Reading database ... 95% (Reading database ... 100% (Reading database ... 20076 files and directories currently installed.) Unpacking lsof (from .../lsof_4.81.dfsg.1-1_amd64.deb) ... dpkg: error processing /var/cache/apt/archives/lsof_4.81.dfsg.1-1_amd64.deb (--unpack): unable to create `/usr/bin/lsof.dpkg-new' (while processing `./usr/bin/lsof'): Permission denied dpkg-deb: subprocess paste killed by signal (Broken pipe) Selecting previously deselected package libmd5-perl. Unpacking libmd5-perl (from .../libmd5-perl_2.03-1_all.deb) ... Selecting previously deselected package rkhunter. Unpacking rkhunter (from .../rkhunter_1.3.4-5_all.deb) ... dpkg: error processing /var/cache/apt/archives/rkhunter_1.3.4-5_all.deb (--unpack): unable to create `/usr/bin/rkhunter.dpkg-new' (while processing `./usr/bin/rkhunter'): Permission denied dpkg-deb: subprocess paste killed by signal (Broken pipe) Selecting previously deselected package unhide. Unpacking unhide (from .../unhide_20080519-4_amd64.deb) ... dpkg: error processing /var/cache/apt/archives/unhide_20080519-4_amd64.deb (--unpack): unable to create `/usr/sbin/unhide-posix.dpkg-new' (while processing `./usr/sbin/unhide-posix'): Permission denied dpkg-deb: subprocess paste killed by signal (Broken pipe) Processing triggers for man-db ... Errors were encountered while processing: /var/cache/apt/archives/lsof_4.81.dfsg.1-1_amd64.deb /var/cache/apt/archives/rkhunter_1.3.4-5_all.deb /var/cache/apt/archives/unhide_20080519-4_amd64.deb E: Sub-process /usr/bin/dpkg returned an error code (1) A package failed to install. Trying to recover: Setting up libmd5-perl (2.03-1) ... Building dependency tree... 0% Building dependency tree... 50% Building dependency tree... 50% Building dependency tree Reading state information... 0% ........... .................... I have removed some lines to reduce the text. All the error messages are in here though. My experience with linux is limited and i am not sure what the problem is or how it is to be resolved. Thanks.

  Read the article

• How much did it cost our competitor to DDoS us at 50 Gbps for two weeks?

  - by MiniQuark

  I know that this question may sound like an invalid serverfault question, but I believe that it's quite valid: the amount of time and effort that a sysadmin should spend on DDoS protection is a direct function of typical DDoS prices. Let me rephrase this: protecting a web site against small attacks is one thing, but resisting 50 Gbps of UDP flood is another and requires time & money. Deciding whether or not to spend that time & money depends on whether such an attack is likely or not, and this in turn depends on how cheap and simple such an attack is for the attacker. So here's the full story: our company has been victim to a massive DDoS attack (over 50 Gbps of UDP traffic, full-time during 2 weeks). We are pretty sure that it's one of our competitors, and we actually know which one, because we were the only two remaining competitors on a very big request for proposal, and the DDoS attack magically stopped the day we won (double hurray, by the way)! These people have proved in the past that they are very dishonest, but we know that they are not technical at all, so we believe that they simply paid for some botnet DDoS service. I would like to know how much these services typically cost, for such a large scale attack. Please do not give any link to such services, I would really hate to give these people any publicity. I understand that a hacker could very well do this for free, but what's a typical price for such an attack if our competitors paid for it through some kind of botnet service? It is really starting to scare me (if we're talking thousands of dollars here, then I am really going to freak off: who knows, they might just hire a hit-man one day?). Of course we filed a complaint, but the police says that they cannot do much about it (DDoS attacks are virtually untraceable, so they say), and our suspicions are not enough to justify them raiding our competitor's offices to search for proofs. For your information, we now changed our infrastructure to be able to sustain such attacks: we now use a major CDN service so that our servers are not directly affected by DDoS attacks. Requests for dynamic pages do get proxied to our servers, but for low level attacks (UDP flood, or Syn floods, for example) we only receive legitimate trafic, so we're fine. If they decide to launch higher level attacks (HTTP flood or slowloris attacks for example), most of the load should be handled by the CDN... at least I hope so! Thank you very much for your help.

  Read the article

• libreadline history lines combine

  - by jettero

  This has been driving me crazy for about three years. I don't know how to fully describe the problem, but I think I can finally describe a way to recreate it. Your milage may vary. I have a mixture of ubuntu server and desktop machines of various versions and a few gentoo machines with various states of disrepair. They all seem to kindof do their own thing, although with similarities. Try this and let me know if you see the same thing. pop open two xterms (TERM=xterm) resize one so they're not the same issue screen -R test1 in one (TERM=screen) and screen -x test1 in the other hooray, typing in one shows up in the other; although notice that their different size produces artifacts and things issue a couple commands in your shell hit ^AF in the one that doesn't fit quite right, now it fits!! scroll back over the history a little goto 6 Eventually you'll notice a couple history lines combine. If you don't, then it's something unique to my setup, which spans various distributions and computers; so that's a confusing concept to me. If you see the thing I'm seeing then this: bash$ ls -al bash$ ps auxfw becomes this: bash$ ls -al; ps auxfw It doesn't happen every time. I have to really play with it — unless I don't want it to happen, then it always does. On some systems (or combinations), I get a line separator like the example above. On some systems, I do not. That I get the line separator on some systems seems to indicate to me that bash supports this behavior. Its history is entirely handled by libreadline and after perusing (ie, carefully reading) the man pages, I couldn't find a single readline setting for combining two history lines. Nor can I find anything in the bash manpage. So, how can I invoke this on purpose? Or, if I can't do that, how can I disable it completely? I would take either answer as a solution. Currently, I only see it when I don't want it.

  Read the article

< Previous Page | 136 137 138 139 140 141 142 143 144 145 146 147  | Next Page >