Search Results

Search found 25790 results on 1032 pages for 'information theory'.

Page 141/1032 | < Previous Page | 137 138 139 140 141 142 143 144 145 146 147 148  | Next Page >

• Why VM snapshots are affecting performance?

  - by Samselvaprabu

  I read in one of the VMware KB article says that snapshots will directly proportional to VM performance. But my team keep asking me how snapshots can affect performance. I would like to give them solid reason behind the statement that snapshots are performance killers. Can any one explain a little bit theory behind why actually snapshots are affecting the performance? Is it just because Disk I/O rate of hard disk would be slow?

  Read the article

• GRE Tunnel over IPsec with Loopback

  - by Alek

  Hello, I'm having a really hard time trying to estabilish a VPN connection using a GRE over IPsec tunnel. The problem is that it involves some sort of "loopback" connection which I don't understand -- let alone be able to configure --, and the only help I could find is related to configuring Cisco routers. My network is composed of a router and a single host running Debian Linux. My task is to create a GRE tunnel over an IPsec infrastructure, which is particularly intended to route multicast traffic between my network, which I am allowed to configure, and a remote network, for which I only bear a form containing some setup information (IP addresses and phase information for IPsec). For now it suffices to estabilish a communication between this single host and the remote network, but in the future it will be desirable for the traffic to be routed to other machines on my network. As I said this GRE tunnel involves a "loopback" connection which I have no idea of how to configure. From my previous understanding, a loopback connection is simply a local pseudo-device used mostly for testing purposes, but in this context it might be something more specific that I do not have the knowledge of. I have managed to properly estabilish the IPsec communication using racoon and ipsec-tools, and I believe I'm familiar with the creation of tunnels and addition of addresses to interfaces using ip, so the focus is on the GRE step. The worst part is that the remote peers do not respond to ping requests and the debugging of the general setup is very difficult due to the encrypted nature of the traffic. There are two pairs of IP addresses involved: one pair for the GRE tunnel peer-to-peer connection and one pair for the "loopback" part. There is also an IP range involved, which is supposed to be the final IP addresses for the hosts inside the VPN. My question is: how (or if) can this setup be done? Do I need some special software or another daemon, or does the Linux kernel handle every aspect of the GRE/IPsec tunneling? Please inform me if any extra information could be useful. Any help is greatly appreciated.

  Read the article

• Excel 2007 - "The macro may not be available in this workbook" Error

  - by Psycho Bob

  We use an Excel sheet that has been protected to prevent modification of it from end users. All in all they are only able to edit certain tabs to add information that will then be used to generate information on other tabs using equations and such. On the tab with the equations, a button is present called "Prep for Internal Hard Copy Print." This button runs a macro that selects the information on the tab, unprotects it, then sends a print job to the user's default printer that contains the unprotected content. Normally this works like a champ. This time around, however, the macro is throwing the following error: Cannot run the macro "FILENAME.xlsx'!MacroName'. The macro may not be available in this workbook or all macros may be disabled. As far as I can tell, the macros are still present within the workbook. This sheet is normally a .xlsm though the user saved it with a different filename as a .xlsx. Also, the macros appear only as MacroName in the .xlsm file and not "FILENAME.xlsx'!MacroName' as it does in the .xlsx. Finally, when I open the .xlsm it asks if I want to enable the macro content while the .xlsx does not prompt for this. Can anyone tell me what's going on with this sheet or know of a way that I can get the macros working in the .xlsx without having to start over with a different sheet?

  Read the article

• Collect temperature and fan speed with munin from Windows 7 PC?

  - by mfn

  Hi, I'm quite fond of munin and using it also at home to monitor my PCs. What was super-duper easy under Linux is pretty much unsolvable for me under Windows: I'd like to monitor CPU and Motherboard temperatures as well as fan speed. On Linux I'm using lm-sensors and the plugin for munin was basically there. I access already some information from my Windows machine via SNMP (disk space, CPU usage, memory usage); the graphs are simple as is the information exposed via SNMP, but they do their job. But when it comes to temperature and fan speed I'm running against a wall. My research so far resulted in that Windows does not by default provide out of the box ability to retrieve temperature/fan speed data. Third party applications are necessary which have know-how how to communicate with the Motherboard chips. The best I cam up with is that SpeedFan exposes a shared memory interface and there exists a library which hooks into Windows SNMP facility and bridges over to SpeedFans shared memory interface; it's called SFSNMP (site currently down). Unfortunately the library doesn't work, there's a bug report at SpeedFan open about it, but it's currently not moving (although the SFSNMP author is active there) . So, unless that's going to work like anytime soon, are there any alternatives? I'm not found of buying any software to get that feature, given that I take it as granted that my system exposes me the information to properly monitor it, but anyway don't just not answer because of this.

  Read the article

• How to configure IIS 7.5 to allow special chars in Url for ASP.NET 3.5?

  - by Sebastian P.R. Gingter

  I'm trying to configure my IIS 7.5 to allow specials chars in the url for ASP.NET. This is important to support wide-spread legacy url's on a new system. Sample url: http://mydomain.com/FileWith%inTheName.html This would be encoded in the url and requested as http://mydomain.com/FileWith25%inTheName.html This simply works, when creating a new web in IIS 7.5, placing a file with the percentage sign in the file name in the web root and pointing the browser to it. This does not work, however, when the web site is an ASP.NET application. ASP.NET always returns a 400.0 - Bad Request error in the WindowsAuthentication module from the StaticFile handler, when pointing to that url. It however displays the requested url correctly and also resolves correctly to the correct physical file (the information from the field 'Physical Path' from the Server error page points to the physically available file). There are hints on how to enable this, so I followed the instructions on these websites step by step: http://dirk.net/2008/06/09/ampersand-the-request-url-in-iis7/ http://adorr.net/2010/01/configure-iis-to-accept-url-with-special-characters.html The second one actually sums up the information from the first post and adds some more information about x64 systems (we're running x64) and on an additional web.config change for this. I tried all that, and still can't get this running from an asp.net web application. And yes: I rebooted after applying the registry changes. So, what do I have to do in addition to the settings described in above posts, to support the legacy url's which contain percentage characters? Additional info: Application Pool mode is integrated. Push after some days. No idea anyone?

  Read the article

• Mysql - innoDb - is in the future! Current system log sequence number

  - by Ward Loockx

  I have this error in my syslog. I restored an older dump to solve this problem, after some reading. Now The errors in syslog are far less than before. But still a few times an hour I get Sep 1 14:23:29 homer mysqld: 120901 14:23:29 InnoDB: Error: page 96637 log sequence number 7 1223357717 Sep 1 14:23:29 homer mysqld: InnoDB: is in the future! Current system log sequence number 6 647303887. Sep 1 14:23:29 homer mysqld: InnoDB: Your database may be corrupt or you may have copied the InnoDB Sep 1 14:23:29 homer mysqld: InnoDB: tablespace but not the InnoDB log files. See Sep 1 14:23:29 homer mysqld: InnoDB: http://dev.mysql.com/doc/refman/5.1/en/forcing-recovery.html Sep 1 14:23:29 homer mysqld: InnoDB: for more information. Sep 1 14:23:29 homer mysqld: 120901 14:23:29 InnoDB: Error: page 96638 log sequence number 8 150027924 Sep 1 14:23:29 homer mysqld: InnoDB: is in the future! Current system log sequence number 6 647303887. Sep 1 14:23:29 homer mysqld: InnoDB: Your database may be corrupt or you may have copied the InnoDB Sep 1 14:23:29 homer mysqld: InnoDB: tablespace but not the InnoDB log files. See Sep 1 14:23:29 homer mysqld: InnoDB: http://dev.mysql.com/doc/refman/5.1/en/forcing-recovery.html Sep 1 14:23:29 homer mysqld: InnoDB: for more information. Sep 1 14:23:29 homer mysqld: 120901 14:23:29 InnoDB: Error: page 96639 log sequence number 7 4208567151 Sep 1 14:23:29 homer mysqld: InnoDB: is in the future! Current system log sequence number 6 647303887. Sep 1 14:23:29 homer mysqld: InnoDB: Your database may be corrupt or you may have copied the InnoDB Sep 1 14:23:29 homer mysqld: InnoDB: tablespace but not the InnoDB log files. See Sep 1 14:23:29 homer mysqld: InnoDB: http://dev.mysql.com/doc/refman/5.1/en/forcing-recovery.html Sep 1 14:23:29 homer mysqld: InnoDB: for more information. Anybody that knows how I can track what database is causing this issue? And how to fix?

  Read the article

• Domain workstation acting up and I can't track it down.

  - by DevNULL

  I have a developer with a Windows XP (SP2) 64 bit machine. If the machine is left on overnight (or any period of time longer than 5-6 hours) it takes 2-3 minutes to open any local drive and his network drives are no longer accessible. Here's what the system logs report... Any Help BTW: The problem just started a week ago and nothing has changed on the domain controller / AD or his machine. --- ERROR 1 Event Type: Error Event Source: NETLOGON Event Category: None Event ID: 5719 Date: 6/8/2010 Time: 9:17:26 AM User: N/A Computer: BFC1 Description: This computer was not able to set up a secure session with a domain controller in domain UR due to the following: There are currently no logon servers available to service the logon request. This may lead to authentication problems. Make sure that this computer is connected to the network. If the problem persists, please contact your domain administrator. ADDITIONAL INFO If this computer is a domain controller for the specified domain, it sets up the secure session to the primary domain controller emulator in the specified domain. Otherwise, this computer sets up the secure session to any domain controller in the specified domain. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: 5e 00 00 c0 ^..A --- ERROR 2 The machine-default permission settings do not grant Local Activation permission for the COM Server application with CLSID {555F3418-D99E-4E51-800A-6E89CFD8B1D7} to the user NT AUTHORITY\LOCAL SERVICE SID (S-1-5-19). This security permission can be modified using the Component Services administrative tool. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. --- ERROR 3 Event Type: Error Event Source: RemoteAccess Event Category: None Event ID: 20106 Date: 6/8/2010 Time: 10:12:18 AM User: N/A Computer: BFC1 Description: Unable to add the interface {E76F0A78-7A0B-4EBB-A081-BA3BD452FC4C} with the Router Manager for the IP protocol. The following error occurred: Cannot complete this function. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: eb 03 00 00 e...

  Read the article

• Terminal Server 2008 Login: Access Denied

  - by user1236435

  When I try to RDP into a Server 2008 Terminal Server, I get a message that says "Access Denied" and an OK button. I setup the licensing mode correctly (per user) and also have setup to allow all remote connections. I get the following in the security event log: Log Name: Security Source: Microsoft-Windows-Security-Auditing Date: 28/06/2012 12:01:16 Event ID: 4656 Task Category: File System Level: Information Keywords: Audit Failure User: N/A Computer: 0BraApps1.brenntagLA.hou Description: A handle to an object was requested. Subject: Security ID: BRENNTAGLA\jaadmin Account Name: jaadmin Account Domain: BRENNTAGLA Logon ID: 0xbbe3f Object: Object Server: Security Object Type: File Object Name: C:\Windows\System32\ServerManager.msc Handle ID: 0x0 Process Information: Process ID: 0x60c Process Name: C:\Windows\System32\mmc.exe Access Request Information: Transaction ID: {00000000-0000-0000-0000-000000000000} Accesses: READ_CONTROL SYNCHRONIZE WriteData (or AddFile) AppendData (or AddSubdirectory or CreatePipeInstance) WriteEA ReadAttributes WriteAttributes Access Reasons: READ_CONTROL: Granted by D:(A;;0x1200a9;;;BA) SYNCHRONIZE: Granted by D:(A;;0x1200a9;;;BA) WriteData (or AddFile): Not granted AppendData (or AddSubdirectory or CreatePipeInstance): Not granted WriteEA: Not granted ReadAttributes: Granted by ACE on parent folder D:(A;;0x1301bf;;;BA) WriteAttributes: Not granted Access Mask: 0x120196 Privileges Used for Access Check: - Restricted SID Count: 0 Event Xml: 4656 1 0 12800 0 0x8010000000000000 1535565 Security 0BraApps1.brenntagLA.hou S-1-5-21-205301047-3902605089-2438454170-21511219 jaadmin BRENNTAGLA 0xbbe3f Security File C:\Windows\System32\ServerManager.msc 0x0 {00000000-0000-0000-0000-000000000000} %%1538 %%1541 %%4417 %%4418 %%4420 %%4423 %%4424 %%1538: %%1801 D:(A;;0x1200a9;;;BA) %%1541: %%1801 D:(A;;0x1200a9;;;BA) %%4417: %%1805 %%4418: %%1805 %%4420: %%1805 %%4423: %%1811 D:(A;;0x1301bf;;;BA) %%4424: %%1805 0x120196 - 0 0x60c C:\Windows\System32\mmc.exe Any ideas?

  Read the article

• What does this diagnostic output mean?

  - by ChrisF

  I recently had a fault with my broadband connection. It turned out to be a fault with the ISP's or teleco's equipment. My ISP posted this diagnostic, but while I understand it in general, I'd like to to know more about the details. I'm assuming that ATM means Asynchronous Transfer Mode and PPP means Point to Point Protocol. It was this that my router was indicating as the fault. xDSL Status Test Summary Sync Status: Circuit In Sync General Information NTE Status: NTE Power Status: Unknown Bypass Status: Upstream DSL Link Information Downstream DSL Link Information Loop Loss: 9.0 17.0 SNR Margin: 25 15 Errored Seconds: 0 0 HEC Errors: 0 Cell Count: 0 0 Speed: 448 8128 TAM Status: Successfully executed operation Network Test: Sub-Test Results Layer Name Value Status Modem pass Transmitter Power (Upstream) 12.4 dBm Transmitter Power (Downstream) 8.8 dBm Upstream psd -38 dBm/Hz Downstream psd -51 dBm/Hz DSL pass Equipment Vendor Name TSTC Equipment Vendor Id n/a Equipment Vendor Revision n/a Training Time 8 s Num Syncs 1 Upstream bit rate 448 kbps Downstream bit rate 8128 kbps Upstream maximum bit rate 1108 kbps Downstream maximum bit rate 11744 kbps Upstream Attenuation 3.5 dB Downstream Attenuation 0.0 dB Upstream Noise Margin 20.0 dB Downstream Noise Margin 19.0 dB Local CRC Errors 0 Remote CRC Errors 0 Up Data Path interleaved Down Data Path interleaved Standard Used G_DMT INP INP Upstream Symbols n/a INP Upstream Delay 4 ms INP Upstream Depth 4 INP Downstream Symbols n/a INP Downstream Delay 5 ms INP Downstream Depth 32 ATM Reason: No ATM cells received fail Number of cells transmitted 30 Number of cells received 0 number of Near end HEC errors 0 number of Far end HEC errors n/a PPP Reason: No response from peer fail PAP authentication nottested CHAP authentication nottested (I'm not sure that Super User is the best place to ask this, but two people have suggested I ask it here so here I am).

  Read the article

• Are swapped in hot-swap drives allocated the same Windows drive letter each time?

  - by Margaret

  We are intending on purchasing a dedicated machine to perform the company's backups. We were considering buying the Dell T310, with the theory that we could swap the drives in and out for offsite backup. (As in, take out a drive, put a version a couple of days' old in its place, the old backup is updated to the current version.) One thing that may stymie this, though, is the system changing drive letters as things get moved in and out. Does anyone know whether this happens?

  Read the article

• Diagnosing Logon Audit Failure event log entries

  - by Scott Mitchell

  I help a client manage a website that is run on a dedicated web server at a hosting company. Recently, we noticed that over the last two weeks there have been tens of thousands of Audit Failure entries in the Security Event Log with Task Category of Logon - these have been coming in about every two seconds, but interesting stopped altogether as of two days ago. In general, the event description looks like the following: An account failed to log on. Subject: Security ID: SYSTEM Account Name: ...The Hosting Account... Account Domain: ...The Domain... Logon ID: 0x3e7 Logon Type: 10 Account For Which Logon Failed: Security ID: NULL SID Account Name: david Account Domain: ...The Domain... Failure Information: Failure Reason: Unknown user name or bad password. Status: 0xc000006d Sub Status: 0xc0000064 Process Information: Caller Process ID: 0x154c Caller Process Name: C:\Windows\System32\winlogon.exe Network Information: Workstation Name: ...The Domain... Source Network Address: 173.231.24.18 Source Port: 1605 The value in the Account Name field differs. Above you see "david" but there are ones with "john", "console", "sys", and even ones like "support83423" and whatnot. The Logon Type field indicates that the logon attempt was a remote interactive attempt via Terminal Services or Remote Desktop. My presumption is that these are some brute force attacks attempting to guess username/password combinations in order to log into our dedicated server. Are these presumptions correct? Are these types of attacks pretty common? Is there a way to help stop these types of attacks? We need to be able to access the desktop via Remote Desktop so simply turning off that service is not feasible. Thanks

  Read the article

• Does putting the XFS log on an SSD significantly improve performance?

  - by Paul Wagland

  I have a five disk array running XFS in RAID5, and I would like to improve it's performance. I have seen some hints that putting the log onto a separate device can help, does putting the log onto an SSD help dramtically? In theory, it should, but I have not been able to find any case studies where someone has actually done this, and buying an SSD and then having it not work well would be inconvenient at best…

  Read the article

• Which type RAM support Our Servers?

  - by Mikunos

  I need to increase the RAM in our DELL servers but with the lshw I cannot see if the RAM installed is a UDIMM or RDIMM. Handle 0x1100, DMI type 17, 28 bytes Memory Device Array Handle: 0x1000 Error Information Handle: Not Provided Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: DIMM Set: 1 Locator: DIMM_A1 Bank Locator: Not Specified Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 1333 MHz (0.8 ns) Manufacturer: 00CE00B380CE Serial Number: 8244850B Asset Tag: 02103961 Part Number: M393B5773CH0-CH9 Handle 0x1101, DMI type 17, 28 bytes Memory Device Array Handle: 0x1000 Error Information Handle: Not Provided Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: DIMM Set: 1 Locator: DIMM_A2 Bank Locator: Not Specified Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 1333 MHz (0.8 ns) Manufacturer: 00CE00B380CE Serial Number: 8244855D Asset Tag: 02103961 Part Number: M393B5773CH0-CH9 Handle 0x1102, DMI type 17, 28 bytes Memory Device Array Handle: 0x1000 Error Information Handle: Not Provided Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: DIMM Set: 2 Locator: DIMM_A3 Bank Locator: Not Specified Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 1333 MHz (0.8 ns) Manufacturer: 00CE00B380CE Serial Number: 8244853E Asset Tag: 02103961 Part Number: M393B5773CH0-CH9 how have we do to know which is the right RAM memory to buy? thanks

  Read the article

• Accidentally dd'ed an image to wrong drive / overwrote partition table + NTFS partition start

  - by Kento Locatelli

  I screwed up and set the wrong output for dd when trying to copy a freenas iso, overwriting the wrong external hard drive. Ironically, I was trying to setup a freenas server for data backup... External drive is only used for data storage, system is entirely intact Drive had a single NTFS partition filing the entire device (2TB WD elements) Drive originally had an MBR partition table. Drive now shows as having a GPT, presumably from the freenas image. Drive was mounted at the time, with maybe a couple kB of data written/read after running dd Drive is just a few months old and healthy (regular SMART / fs checks) I have not reboot the OS (crunchbang) /proc/partition still holds the correct information (and has been stored) Have dd's output (records in / out / bytes) testdrive did not find any partitions on quick or deep search running photorec to recover the more important data (a couple recent plaintext files that hadn't been backed up yet). Vast majority of disk content ( 80%) is unnecessary media files. My current plan is to let photorec do it's thing, then recreate the mbr with gparted and use cfdisk to create another NTFS partition using the sector information from /sys/block/.../. Is that a good course of action (that is, a chance of success)? Or anything else I should try first? Possibly relevant information: dd if=FreeNAS-8.0.4-RELEASE-p3-x86.iso of=/dev/sdc: 194568+0 records in 194568+0 records out 99618816 bytes (100 MB) copied grep . /sys/block/sdc/sdc*/{start,size}: /sys/block/sdc/sdc1/start:2048 /sys/block/sdc/sdc1/size:3907022848 cat /proc/partitions: major minor #blocks name ** Snipped ** 8 32 1953512448 sdc 8 33 1953511424 sdc1 current fdisk -l output: WARNING: GPT (GUID Partition Table) detected on '/dev/sdc'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sdc: 2000.4 GB, 2000396746752 bytes 255 heads, 63 sectors/track, 243201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sdc doesn't contain a valid partition table

  Read the article

• Collect temperature and fan speed with munin from Windows 7 PC?

  - by nfm

  Hi, I'm quite fond of munin and using it also at home to monitor my PCs. What was super-duper easy under Linux is pretty much unsolvable for me under Windows: I'd like to monitor CPU and Motherboard temperatures as well as fan speed. On Linux I'm using lm-sensors and the plugin for munin was basically there. I access already some information from my Windows machine via SNMP (disk space, CPU usage, memory usage); the graphs are simple as is the information exposed via SNMP, but they do their job. But when it comes to temperature and fan speed I'm running against a wall. My research so far resulted in that Windows does not by default provide out of the box ability to retrieve temperature/fan speed data. Third party applications are necessary which have know-how how to communicate with the Motherboard chips. The best I cam up with is that SpeedFan exposes a shared memory interface and there exists a library which hooks into Windows SNMP facility and bridges over to SpeedFans shared memory interface; it's called SFSNMP (site currently down). Unfortunately the library doesn't work, there's a bug report at SpeedFan open about it, but it's currently not moving (although the SFSNMP author is active there) . So, unless that's going to work like anytime soon, are there any alternatives? I'm not found of buying any software to get that feature, given that I take it as granted that my system exposes me the information to properly monitor it, but anyway don't just not answer because of this.

  Read the article

• How can I set up a touchscreen as the non-primary monitor in a dual monitor situation?

  - by bazzjedi

  I have been looking for information about using a second monitor, and thought of using a touchscreen. Will a touchscreen monitor work in a dual setup if it is not the main monitor? I haven't found any information on this; I've only found information about the touchscreen being the main monitor. That is, except at this SU question (snippet below): If you mean do the touch screen features still work on the other machine, the answer is yes. Past that, you can even see some of the touch screen features on a non touch screen monitor (just not the multi touch features!) For example, on the taskbar, click (without releasing) on any icon and then drag the mouse up, and you will see that it does the same as using your finger and dragging up. I have a HP 2510 for the main monitor. I'm thinking of adding a HP 2310ti (the touchscreen) as the secondary. My graphics card is a geforce gtx 295. I'm running Windows 7 Professional.

  Read the article

• How can I change the apache config for a virtual host, from the shell on a whm/cpanel system?

  - by Chiggsy

  I wanted to change the setting for a virtual host in a hurry I knew how to "just do it" but I'm not very familiar with the restrictions of the cpanel system. I read the theory of the config system and regardless of my feelings on the matter I understand where they are coming from. However in that world view, there must be a way to interact with the system from a command line interface, not just for httpd.conf but for the virtual host containers as well EDIT: reworded this question a bit to show I was talking about a virtual host container.

  Read the article

• Patch management on multiple systems

  - by Pierre

  I'm in charge of auditing the security configuration of an important farm of Unix servers. So far, I came up with a way to assess the basic configuration but not the installed updates. The very problem here is that I just can't trust the package management tools on those machine. Indeed some of them did not sync with the repository for a long time (So I can't do a "yum check-updates" on Redhat for example). Some of those servers are not even connected to the internet and use an company repository. Another problem is that I have multiple target systems: AIX, Debian, Centos/Redhat, etc... So the version could be different (AIX) and the tools available will be different. And, last but not least, I can't install anything on the target system. So I need to use a script to retrieve the information and either: process it directly or save the information to be able to process it later on a server (Which may happen to run a different distribution than the one on which the information have been retrieved). The best ideas I could come up with were: either retrieve the list of installed packages on the machine (dpkg -l for example on debian) and process it on a dedicated server (Directly parsing the "Packages" file of debian repositories). Still, the problem remains the same for AIX and Redhat... or use Nessus' scripts to assess vulnerability on the installed packages, but I find this a bit dirty. Does anyone know any better/efficient way of doing this ? P.S: I already took time to review some answers to similar problems. Unfortunately Chef, puppet, ... don't meet the requirements I have to meet. Edit: Long story short. I need to have the list of missing updates on a Unix system just like MBSA on Windows. I'm not authorized to install anything on this system as it's not mine. All I have are scripts languages. Thanks.

  Read the article

• iTunes copy just metadata (song and album ratings, playlists) from iPod

  - by Jared Updike

  I have an iPod touch that I synched with my Windows computer (iTunes 9.0 I think) until my harddrive failed and I lost my entire library. I rebuilt the library (songs) from a year old backup (and various other source for songs) but my playlists and ratings are of course a year old. My iPod itself has most of the playlists and ratings I care most about (favorite songs and albums, rated 4 and 5, for example). I have a catch 22 situation where I feel nervous that I haven't backed up my iPod in around 4 months (when my drive failed) so I'd like to back it up as soon as possible... but if I back it up I have to clear all the songs and playlists and copy them back, which I can't really do since I need to rebuild my playlists on my computer first (using the data only available on my iPod!) The question: is there a better way to READ the information off my iPod than doing it manually, song by song and album by album and playlist by playlist (XML, text dump, database, spreadsheet, anything). In other words, mostly I want the information (metadata like ratings and playlists, not songs) copied off the iPod so I can more quickly get my iTunes library ratings and playlists re-built (manually) so I can finally wipe the music and back up my apps, etc. Then I'd like to copy the music back immediately. The part I'd like to avoid is manually navigating everything on my iPod to read through all the playlists and ratings (50 GB, 6,000+ songs) as I re-enter all of that data by hand. I've done a few dozen albums and it's pretty time consuming having to tap around on the iPod. Reading from a spreadsheet (for example, or XML which I could write a script to get into spreadsheet form) would probably help tremendously, plus then I'd have a backup of that information somewhere besides just my iPod.

  Read the article

• Hide/Replace Nginx Location Header?

  - by Steven Ou

  I am trying to pass a PCI compliance test, and I'm getting a single "high risk vulnerability". The problem is described as: Information on the machine which a web server is located is sometimes included in the header of a web page. Under certain circumstances that information may include local information from behind a firewall or proxy server such as the local IP address. It looks like Nginx is responding with: Service: https Received: HTTP/1.1 302 Found Cache-Control: no-cache Content-Type: text/html; charset=utf-8 Location: http://ip-10-194-73-254/ Server: nginx/1.0.4 + Phusion Passenger 3.0.7 (mod_rails/mod_rack) Status: 302 X-Powered-By: Phusion Passenger (mod_rails/mod_rack) 3.0.7 X-Runtime: 0 Content-Length: 90 Connection: Close <html><body>You are being <a href="http://ip-10-194-73-254/">redirect ed</a>.</body></html> I'm no expert, so please correct me if I'm wrong: but from what I gathered, I think the problem is that the Location header is returning http://ip-10-194-73-254/, which is a private address, when it should be returning our domain name (which is ravn.com). So, I'm guessing I need to either hide or replace the Location header somehow? I'm a programmer and not a server admin so I have no idea what to do... Any help would be greatly appreciated! Also, might I add that we're running more than 1 server, so the configuration would need to be transferable to any server with any private address.

  Read the article

• ssh - "Connection closed by xxx.xxx.xxx.xxx" - using password

  - by Michael B

  I attempted to create an new user account that I wish to use to log in using ssh. I did this (in CentOs): /usr/sbin/adduser -d /home/testaccount -s /bin/bash user passwd testaccount This is the error I receive when trying to log in via ssh: ~/.ssh$ ssh -v [email protected] OpenSSH_5.1p1 Debian-5ubuntu1, OpenSSL 0.9.8g 19 Oct 2007 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to xxx.xxx.xxx [xxx.xxx.xxx.xxx] port 22. debug1: Connection established. debug1: identity file /home/user/.ssh/identity type -1 debug1: identity file /home/user/.ssh/id_rsa type 1 debug1: Checking blacklist file /usr/share/ssh/blacklist.RSA-2048 debug1: Checking blacklist file /etc/ssh/blacklist.RSA-2048 debug1: identity file /home/user/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_4.3 debug1: match: OpenSSH_4.3 pat OpenSSH_4* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.1p1 Debian-5ubuntu1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-cbc hmac-md5 none debug1: kex: client->server aes128-cbc hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'xxx.xxx.xxx.xxx' is known and matches the RSA host key. debug1: Found key in /home/user/.ssh/known_hosts:8 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,gssapi-with-mic,password debug1: Next authentication method: gssapi-with-mic debug1: Unspecified GSS failure. Minor code may provide more information No credentials cache found debug1: Unspecified GSS failure. Minor code may provide more information No credentials cache found debug1: Unspecified GSS failure. Minor code may provide more information debug1: Next authentication method: publickey debug1: Offering public key: /home/user/.ssh/id_rsa debug1: Authentications that can continue: publickey,gssapi-with-mic,password debug1: Trying private key: /home/user/.ssh/identity debug1: Trying private key: /home/user/.ssh/id_dsa debug1: Next authentication method: password testaccount@xxx's password: Connection closed by xxx.xxx.xxx.xxx The "connection closed" message appeared immediately after entering the password (if I enter the wrong password it waits and then prompts for another password) I am able to log in from the same computer using other accounts that had been setup previously. When logged into the remote machine I am able to do 'su testaccount' Thanks for your time.

  Read the article

• iTunes copy just metadata (song and album ratings, playlists) from iPod

  - by Jared Updike

  I have an iPod touch that I synched with my Windows computer (iTunes 9.0 I think) until my harddrive failed and I lost my entire library. I rebuilt the library (songs) from a year old backup (and various other source for songs) but my playlists and ratings are of course a year old. My iPod itself has most of the playlists and ratings I care most about (favorite songs and albums, rated 4 and 5, for example). I have a catch 22 situation where I feel nervous that I haven't backed up my iPod in around 4 months (when my drive failed) so I'd like to back it up as soon as possible... but if I back it up I have to clear all the songs and playlists and copy them back, which I can't really do since I need to rebuild my playlists on my computer first (using the data only available on my iPod!) The question: is there a better way to READ the information off my iPod than doing it manually, song by song and album by album and playlist by playlist (XML, text dump, database, spreadsheet, anything). In other words, mostly I want the information (metadata like ratings and playlists, not songs) copied off the iPod so I can more quickly get my iTunes library ratings and playlists re-built (manually) so I can finally wipe the music and back up my apps, etc. Then I'd like to copy the music back immediately. The part I'd like to avoid is manually navigating everything on my iPod to read through all the playlists and ratings (50 GB, 6,000+ songs) as I re-enter all of that data by hand. I've done a few dozen albums and it's pretty time consuming having to tap around on the iPod. Reading from a spreadsheet (for example, or XML which I could write a script to get into spreadsheet form) would probably help tremendously, plus then I'd have a backup of that information somewhere besides just my iPod.

  Read the article

• Is there a faster way to change default apps associated with file types on OS X?

  - by Lri

  Is there anything more convenient than using RCDefaultApp or Magic Launch, or just repeatedly pressing the Change All buttons in Finder's information panels? I thought about writing a shell script that would modify the CFBundleDocumentTypes arrays in Info.plist files. But each app has multiple keys (sometimes an icon) that would need to be changed. lsregister can't be used to make specific modifications to the Launch Services database. $ `locate lsregister` -h lsregister: [OPTIONS] [ <path>... ] [ -apps <domain>[,domain]... ] [ -libs <domain>[,domain]... ] [ -all <domain>[,domain]... ] Paths are searched for applications to register with the Launch Service database. Valid domains are "system", "local", "network" and "user". Domains can also be specified using only the first letter. -kill Reset the Launch Services database before doing anything else -seed If database isn't seeded, scan default locations for applications and libraries to register -lint Print information about plist errors while registering bundles -convert Register apps found in older LS database files -lazy n Sleep for n seconds before registering/scanning -r Recursive directory scan, do not recurse into packages or invisible directories -R Recursive directory scan, descending into packages and invisible directories -f force-update registration even if mod date is unchanged -u unregister instead of register -v Display progress information -dump Display full database contents after registration -h Display this help

  Read the article

• How to create an GUI that communicate with the USB Devices using win32 programming [migrated]

  - by VINAYAK

  I am doing my Project using win 32 programming.I am just learning about win32 programming and able to create an UI.I want to communicate with an USB Device with that UI.SO,How can i go for that?Is there any predefined functions will be there are we need to create the function for communicating with the OS and get the devices List and got the details about them. My purpose is to , 1.Creating an UI that tells about the Basic information about the device(We want to send a control request to the device to get the descriptors). 2.For that first of all i want to communicate with the OS for device attachment.That will lead to get the information about the device and Enumeration takes place and then only i request the device information through descriptors by using standard Requests. 3.And also i want to create the driver for my device.That will also need to achieve for communicating with OS(Windows). So,can anyone help me about this?How can i achieve this or approach this? Note: I am at the entry level now so anyone give response will be in a detailed format like step by step process would be appreciable.

  Read the article

• Kickstarting an Ubuntu Server 10.04 installation (DHCP fails)

  - by William

  I'm trying to automate the network installation of Ubuntu 10.04 LTS with an anaconda kickstart and everything seems to running except for the initial DHCP autoconfiguration. The installer attempts to configure the install via DHCP but fails on its first attempt. This brings me to a prompt where I can retry DHCP and it seems to always work on the second attempt. My issue is that this is not really automated if I have to hit retry for DHCP. Is there something I can add to the kickstart file so that it will automatically retry or better yet not fail the first time? Thanks. Kickstart: # System language lang en_US # Language modules to install langsupport en_US # System keyboard keyboard us # System mouse mouse # System timezone timezone America/New_York # Root password rootpw --iscrypted $1$unrsWyF2$B0W.k2h1roBSSFmUDsW0r/ # Initial user user --disabled # Reboot after installation reboot # Use text mode install text # Install OS instead of upgrade install # Use Web installation url --url=http://10.16.0.1/cobbler/ks_mirror/ubuntu-10.04-x86_64/ # System bootloader configuration bootloader --location=mbr # Clear the Master Boot Record zerombr yes # Partition clearing information clearpart --all --initlabel # Disk partitioning information part swap --size 512 part / --fstype ext3 --size 1 --grow # System authorization infomation auth --useshadow --enablemd5 %include /tmp/pre_install_ubuntu_network_config # Always install the server kernel. preseed --owner d-i base-installer/kernel/override-image string linux-server # Install the Ubuntu Server seed. preseed --owner tasksel tasksel/force-tasks string server # Firewall configuration firewall --disabled # Do not configure the X Window System skipx %pre wget "http://10.16.0.1/cblr/svc/op/trig/mode/pre/system/Test-D" -O /dev/null # Network information # Start pre_install_network_config generated code # Start of code to match cobbler system interfaces to physical interfaces by their mac addresses # Start eth0 # Configuring eth0 (00:1A:64:36:B1:C8) if ip -o link show | grep -i 00:1A:64:36:B1:C8 then IFNAME=$(ip -o link show | grep -i 00:1A:64:36:B1:C8 | cut -d" " -f2 | tr -d :) echo "network --device=$IFNAME --bootproto=dhcp" >> /tmp/pre_install_ubuntu_network_config fi # End pre_install_network_config generated code %packages openssh-server

  Read the article

< Previous Page | 137 138 139 140 141 142 143 144 145 146 147 148  | Next Page >