Search Results

Search found 19446 results on 778 pages for 'network printer'.

Page 141/778 | < Previous Page | 137 138 139 140 141 142 143 144 145 146 147 148  | Next Page >

• Upgrade Fiber Optics from 100Base-FX to 1000Base-SX

  - by Byron Wilcox

  We currently have two HP Procurve 2312s connected using two 100-FX-SC transceivers. I am looking to upgrade to new managed Cisco Catalyst switches that use 1000Base-SX transceivers, will the same cabling I have now work or what will I need to upgrade to make it work?

  Read the article

• Configure BL-C111A IP Camera

  - by csmba

  I am an ATT DSL customer. I want the camera to send an email when motion detection is triggered. Can anyone tell me how he managed to do that using: GMail (I cannot because I don't think it supports SSL) other alternatives if GMail is not supported

  Read the article

• IPMI not fucntioning with Network Bonding

  - by muhammed sameer

  Hey, I am having problems with running IPMI on my servers that have network bonding enabled. Platform: CentOS release 5.3 (Final) Kernel: 2.6.18-92.el5 64bit Dell PowerEdge 1950 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet I have bonded the interface eth0 and eth1 as active passive, with eth0 as the active interface, below is conf description from /proc Bonding Mode: fault-tolerance (active-backup) Primary Slave: eth0 Currently Active Slave: eth0 MII Status: up MII Polling Interval (ms): 30 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth0 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:22:19:56:b9:cd Slave Interface: eth1 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:22:19:56:b9:cf My IPMI device is as follows IPMI Device Information Interface Type: KCS (Keyboard Control Style) Specification Version: 2.0 I2C Slave Address: 0x10 NV Storage Device: Not Present Base Address: 0x0000000000000CA8 (I/O) Register Spacing: 32-bit Boundaries I Have used openIPMI as well as freeipmi both to control the chassis via the IPMI card, but on servers which have bonding enabled, the command times out, below is the full run of the command with debug info. ipmi_lan_send_cmd:opened=[0], open=[4482848] IPMI LAN host 70.87.28.115 port 623 Sending IPMI/RMCP presence ping packet ipmi_lan_send_cmd:opened=[1], open=[4482848] No response from remote controller Get Auth Capabilities command failed ipmi_lan_send_cmd:opened=[1], open=[4482848] No response from remote controller Get Auth Capabilities command failed Error: Unable to establish LAN session Failed to open LAN interface Unable to get Chassis Power Status On the other hand I configured IPMI on a box with the same specs as mentioned above without bonding and IPMI works perfectly. Has anyone faced this problem with IPMI + Bonding ? I would be thankful is someone helps circumvent this issue. Muhammed Sameer

  Read the article

• Virutal Machine loses network connectivity on Hyper V Cluster

  - by Chris W

  We're running a number of VMs on a 6 node failover cluster of blades using Hyper V. We have an intermittent issue (every few days at different times - not a fixed frequency) of VMs losing network connectivity. Console access to the VM suggests all is fine and the underlying blade has normal connectivity. To resolve the problem we either have to re-start the VM or, more usually, we do a live migration to another blade which fires up connectivity and we then migrate it back to the original blade. I've had 3 instances of this happen with a specific VM running on a particular blade however it has happened once with a different VM running on a different blade. All VMs and blades have the same basic setup and are running Windows 2008 R2. Any ideas where I should be looking to diagnose the possible causes of this problem as the event logs provide no help? Edit: I've checked that each blade is running the latest NIC drivers and all seem to be fine. Something that is confusing me - a failover or restart of the VM resolves the issue. Whilst I need to work out the underlying issue that is causing the NICs to hang I'm also concerned that the VM didn't failover to another node which would have solved the outage for me. Is there a way to configure the cluster so that it can tell that the VM guest has lost connectivity and fail it over? As things stand the cluster is assuming that the VM is running happily as I presume Hyper V says everything is great even though there is a problem.

  Read the article

• What device can create wireless network while connecting to an ethernet router

  - by Nicolo

  Hi, I have access to an ethernet port of a wireless router. I simply connect my laptop to it via an ethernet cable. There are a total of four such ports on the wireless router. Now I want to connect a device (a wireless access point? wireless bridge? wireless switch?) via an ethernet cable to one of the other ethernet ports of the router. I want this device to act as a kind of wireless switch - it should "split" the ethernet connection coming from the router to two or more computers that connect to this device via a wireless. Basically, I have a wireless router with its wireless function switched off. I don't know the password for that router so can't activate the wireless function. Don't know the password of the ISP either. The only thing I can do is to connect via ethernet cable to the wireless router and this does not require a password. Now I want to use that connection and build a wireless upon it. What kind of device do I need? I am not really very well informed about network management and find the descriptions "wireless access point", "wireless bridge", "wireless switch" confusing. I know what an ethernet switch is - what I need is a device which would do the same but by allowing the clients to connect to it via a wireless. What kind of device would do that? Any recommendations about specific products?

  Read the article

• way to access Win networked folder on Mac like one can with Run box on Win

  - by Nik

  I was wondering if there is a way to access a deeply nested shared networked Windows folder on Mac (Lion) like you can on windows with the Run box. say I know the folder I want is on the computer Homer-PC, the G drive, the folder ABC/234/CDE on Windows I can Win+R then \Homer-PC\G\ABC\234\CDE return and it should open that folder directly, Is there something similar on the Mac? Or is there some tiny apps that I can use to do that? Thank You

  Read the article

• A network-related or instance-specific error occurred while establishing a connection to SQL Server

  - by sf

  Hi, I'm getting the following error when trying to load an Asp.NET MVC App on IIS 7 with Sql Server 2008 Express. The App uses Linq to SQL. A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) I've done some searching and all answers point to enabling TCP connections in Sql Server Configuration which I have done to no avail. The connection string I am using is: Server=SERVERNAME\SQLEXPRESS;Database=DBName;Integrated Security=true The catch. I have another app that already could talk to the Sql Server just fine. Even before playing around with the Sql Server Configuration Settings. The other app uses the following connectionstring: Data Source=SERVERNAME\SQLEXPRESS;Initial Catalog=OtherDbName;Integrated Security=True;Persist Security Info=False;Connect Timeout=120 I've tried this connectionstring on the app that isn't working and it still doesn't work. Please help. I think i'm about to go crazy

  Read the article

• Hyper-V server 2012 nic teaming setup and virtual switch configuration

  - by Calvin

  I have a server with 2 nics. I installed Hyper-v 2012 server (not windows server 2012, no gui) I am trying to set up load balancing. I have both nics in the same switch currently in trunk mode and no native vlan. I use the new-netlbfoteam command to create a team with both nics, I can then "set-netlbfoteamnic "Nic Team" -vlanid 4" so that its available to me with a DHCP or static address but as soon as I try to create a virtual switch it becomes unresponsive. My guess is that is due to it removing the vlan tagging I setup. if I add-netlbfoteamnic and set it for vlan 4, then set the IP I can ping it from my management computer but I just get an error "an error occurred while attempting to connect to server "xxxxxx" Check that the Virtual Machine Management service is running and that you are authorized to connect to the server."

  Read the article

• How can I ping a range of IPs simultaneously

  - by Jon Cage

  I have a bunch of machines on an IP range which I want to ping simultaneously as a quick and dirty way of telling which ones are switched on. What (free) software can I use to do this? [Edit] I should add that I'm using Windows (Vista)

  Read the article

• Even googling not allowed ? Why ?

  - by sagar

  Please read message bellow. Access has been denied 127.0.0.1! Access to the page: http://www.google.co.in/search?hl=en&client=firefox-a&hs=F58&rls=org.mozilla%3Aen-US%3Aofficial&q=email+us&meta=&aq=f&aqi=g10&aql=&oq=&gs_rfai= ... has been denied for the following reason: Weighted phrase limit exceeded. By reading above message, you can easily understand that - it's a firewall message. I also know that. The problem is "Firewall" is allowing any kind of googling. But when I google "email us" - above message is displayed. My question is why does this happen ? ( means - why googling not allowed on this words ? ) ( Please don't tell that - contact your system administrator. ) What does this mean - Weighted phrase limit exceeded. ? sagar.

  Read the article

• Nagios plug-in check_snmp receives NO SNMP data from a CISCO Router

  - by Shehryar

  I have tried setting up Nagios on Ubuntu 10.10, successfully installed and can login to web interface, I am however stuck on configuring snmp or I am doing something wrong here, i have followed various sites / nagios wiki to setup configuration (cfg) files. When I check on the web interface, it gives the following error on one of my cisco router: Current Status: UNKNOWN (for 0d 2h 55m 56s) Status Information: SNMP problem - No data received from host CMD: /usr/bin/snmpget -t 1 -r 5 -m RFC1213-MIB -v 1 [authpriv] 192.168.1.1:161 ifOperStatus.1 On the command-line itself, when I type the following, it just sits there waiting and waiting : sudo /usr/local/nagios/libexec/check_snmp -H 192.168.1.1 -C Routers -o sysUpTime.0 When I type the following command : I get an OK /usr/bin/snmpget -v1 192.168.1.1:161 1.3.6.1.2.1.1.5.0 -c "Routers" I have configured SNMP properly on our cisco device as we can collect SNMP Data via two other monitoring tool (SolarWinds and Manage Engine), we are tempted towards Nagios as its opensource. Will be grateful if someone could assist in rectifying this situation and guide me with setting up nagios to monitor Cisco Routers, Switches and a Few Servers. We want to monitor Bandwidth, cpu utilization, uptime and other necessary counters. Will be grateful for your assistance Thanks for reading Shehryar

  Read the article

• Network cabling with multiple patch panels?

  - by dannymcc

  I am in the very early stages of planning a network cabling upgrade in our office, mainly to upgrade the old cables from Cat5 to either 5e or 6. I am also planning on upgrading all of our 10/100 switches to 10/100/1000 switches. I would like to have three small wall mounted cabinets spread around the building, each with a patch panel and switch. These would all lead back to our server room. The question is; should I have two patch panels in each wall cabinet, one with 24 or 48 ports that are connected to a matching patch panel in the server room. The second patch panel would then link to each device in that cabinets area. Then I wouldn't put a switch in the small cabinets. All switching would be done in the server room. Or, should I have one main cable from the server room to each of the cabinets - plugged straight into the switch and the patch panel is for devices in the cabinets area? I hope that makes sense!

  Read the article

• Recommendations for a Surveillance Camera Kit that I can remotely access

  - by dr dork

  Hello! I just saw a deal on Newegg for this surveillance camera kit and it got me to thinking about installing a setup in my house. Can anyone recommend a decent surveillance camera kit, nothing fancy, that will allow me to access it from any computer (whether it's through a webpage or client program I need to install)? Thanks so much in advance for your help, I'm going to start researching this question right now.

  Read the article

• Can't view other computers on Network

  - by Darkart

  Systems: My Machine: Windows 7 Ultimate connected through ethernet into router Her Machine--Other Machine: Windows 7 Ultimate connected through wireless Router:F5D8236-4 N Wireless Router Version 1 Firmware: 2.01.03 (Apr 28 2009) ISP: Comcast Problem: I can not view the "Other Machine" on the network at all. I opened command prompt and ran net view and saw the pc name. I tried pinging the pc and it times out. Went inside the router and tried viewing the computer on the DHCP list and it can not be seen. I restored the router back to default settings and firmware and completely reset the modem and router, and created home group. I went to the other machine to configure home group settings and made sure that both PC's had identical settings. She was able to see my machine but I could not see hers. I restarted both machines and now we cant see each other at all. Also her PC ("Other Machine") had exclamation mark in the wireless icon but was connected just fine. There is no firewalls on currently or anti-virus enabled, and still can not see each other. Right now I am checking for updated drivers for the wireless card, but my question is could it be the router or something hardware related? I have went through all the settings in the Home group and visited most FAQ's and still no luck. Also as it stands I can not view her machine inside the router DHCP Client List :(

  Read the article

• Show both routers SSID with Wireless bridge [closed]

  - by Valter Henrique

  I have two router 'GVT-1' (the main router) and 'GVT-2' (the second router), this seconds router is used as a repeater only, so I setup a wireless bridge but after I did that it only show 'GVT-2' and if I go closer the 'GVT-1' the signal gets weak cause I'm far from the second router. What I wish is to had the same connection with a wide signal, there's something that I cand do about it ? Thanks.

  Read the article

• Dual NIC internet access

  - by JavaRocky

  Q1. If a computer had two NICs, lets say windows, on which interface would HTTP traffic (or any for that matter) go out on. Not sure how the routes table would look like. Q2. If one of the NICs link becomes unresponsive, would traffic be automatically routed to the other NIC? Thanks.

  Read the article

• Our wi-fi at work is ridiculously slow, will adding more range extenders improve it?

  - by john

  At work, we have two wireless networks (e.g., Work1 Work2); the Work2 is used downstairs and Work1 is used upstairs. However, both are notoriously slow. The connection is better when we are wired in, but unfortunately due to our building being very old and our company growing very fast, most employees are not seated near the walls where the ethernet cables are. I had Cox, our ISP, run a bandwidth utilization test and it doesn't seem like we are capping out on upstream/downstream, which leads me to believe that it's strictly an issue with the wireless networks (which were implemented before I got there). The wireless networks are both Apple Airport Extremes. Is there anything I can do to improve the situation for everyone? Speeds are extremely slow, and sometimes drops out.

  Read the article

• scheduled task share permissions

  - by Enriquev

  Hello, I would like to know if there is a way I can share : \\server\Scheduled Tasks On server 2003 with normal users, cause as far as I can tell it seems only administrators can see this share, is there anyway I can change this share's permission and add users or groups? I know I can change permission on the jobs themselves, but normal users don't see the folder at all, so they cant access the jobs... Thank You.

  Read the article

• Basic IP address structure

  - by dannymcc

  We currently have a few servers, around 30-40 workstations and 16 phones. Each device has a static IP address. As an example the standard settings for a new workstation is; IP: 192.168.1.XXX Subnet: 255.255.255.0 Gateway: 192.168.1.99 DNS: 192.168.1.50 As I am slowly exploring new server OS's and virtualisation etc. I am getting close to wanting a wider range of IP addresses. What I would like to do is seperate the devices by IP as follows: Servers 192.168.1.XXX Workstations 192.168.2.XXX Printers 192.168.3.XXX Phones 192.168.4.XXX VM's 192.168.5.XXX Is this a bad idea, or is this a common way of doing things? My biggest concern is the phones and subnet masks. The phones are managed by our provider although I have access to the server that runs them. Would I need to change the subnet mask to 255.255.0.0 on all devices? Or only those that change? For example, the phones don't need to connect to any other devices other than other phones and the phone server. So if I have the phones on 192.168.1.XXX with a subnet mask of 255.255.255.0 and then moved everything I had complete ownership/control of to 192.168.X.XXX with a new subnet mask of 255.255.0.0. Would that work?

  Read the article

• Tor over IPSEC or IPSEC over Tor?

  - by StraightUp

  Do you think Tor should be run over IPsec, or IPsec over Tor? Please be specific as of why you made this decision. Thanks

  Read the article

• Why is Transmission constantly active?

  - by Dov

  I am using Transmission (1.92, the latest version) in Mac OS X 10.6.2 Snow Leopard, and have noticed that, without any torrents (at all, not even paused), Little Snitch reports constant activity from it. What's going on? I'd always assumed when I saw that with Torrents loaded but inactive, it had to do with the DHT, or some such kind of scanning activity. But what could it be doing when no torrents are loaded at all?

  Read the article

• Can I issue wireless clients with IP address on different subnet?

  - by Beanz

  We have a very standard setup with a Windows Server 2003 domain controller issuing IP addresses using DHCP. This works fine. Internet access is managed via Microsoft ISA Server 2006 Standard. Clients are required to authenticate and this works fine. We now need to provide wireless internet access to visitors for laptops, iPhones etc. We've bought a couple of Netgear access points so I was thinking we might be able to issue wireless clients connected to it with an IP address on a different subnet and then allow non-authenticated Internet access via the ISA Server for that IP range. Does that sound plausible? I'm not even sure if I can issue a different subnet to wireless clients.

  Read the article

• Permission denied when running Rails app in VirtualBox Ubuntu guest with files on Windows host

  - by Ola Tuvesson

  I think I'm close to having my dev environment set up exactly the way I want, but one final snag remains. I'm running VirtualBox on a Windows 7 64bit host, with my dev enviroment inside a Ubuntu 12.04 guest. I want to keep the files for my projects on the host filesystem - partly so I can access them when the Ubuntu guest is not running, but also so I can use Tortoise and other Windows based tools (cough Photoshop), and it also eases my backup scheme somewhat. So I've got a folder "Rails" on my NTFS drive, which I've shared (Samba) from the host with a user specifically created for the Ubuntu guest. The mount point has been set up and an entry added to fstab (cifs), using a credentials file and the options iocharset=utf8,mode=0777,dir_mode=07??77 This mounts fine and my Ubuntu user has both read and write permissions to the contents. But when I try to start my Rails app I get permission errors on any files the app needs to write to (e.g. the log file) - why is that? Are there any major conceptual flaws with this approach? Would I be better off using the VBox "shared folders" function?

  Read the article

• Problems accessing shared folder in Windows Server 2008

  - by Triynko

  In Windows Server 2008, I have a shared folder. For my username: NTFS permission (read/modify) Share Permissions (read/modify) Result when trying to access the share: I can traverse directory and read files, but I cannot write files. When I try to examine my effective permissions, it says "Windows can't calculate the effective permissions for [My Username]". The folder is owned by the Administrators group (the default), and NTFS read/write permissions are granted to my username, which is a member of the Administrators group. I notice that to make any changes to the folder locally require me to acknowledge a UAC prompt. Why does that prompt appear? I also tried creating a new group, giving it full NTFS permissions, and full control in the shared permissions, and added my username to the group. The result is even worse... I cannot even traverse the shared folder directories or read anything at all.

  Read the article

• Can't connect to a share.

  - by AngryHacker

  Hello, I have a laptop with a Windows XP Tablet Edition installed. I have several users setup on the laptop (mostly me and my kids). When I try to connect to its administrative share via \DadLaptop\c$ from a Windows 2000 Professional machine, it prompts me for a user name and password. However, after I enter it, it always tells me "incorrect password or unknown username". As a test I setup another share, called "test" and tried to connect to that. It worked fine, didn't even ask me for a password, just connected to it and that's that. All the networking is wireless. I am connecting with an admin account (admin on the target computer). What am I missing? Why can't I connect to an administrative share?

  Read the article

< Previous Page | 137 138 139 140 141 142 143 144 145 146 147 148  | Next Page >