Search Results

Search found 14745 results on 590 pages for 'setting'.

Page 141/590 | < Previous Page | 137 138 139 140 141 142 143 144 145 146 147 148  | Next Page >

• Routing Traffic With OpenVPN

  - by user224277

  Few minutes ago i configured my VPN server, and actually I can connect to my VPN but all trafic is going through my normal home network. On my OpenVPN application I've got an information : Server IP: **.185.***.*10 Client IP: 10.8.0.6 Traffic: 7.3 KB in, 5.6 KB out Connected: 10 June 2014 19:21:59 So everything is connected but how I can setup on windows 7 that all trafic have to go through OpenVPN network card ?? Client setting : client dev tun proto udp # enter the server's hostname # or IP address here, and port number remote **.185.***.*10 1194 resolv-retry infinite nobind persist-key persist-tun # Use the full filepaths to your # certificates and keys ca ca.crt cert user1.crt key user1.key ns-cert-type server comp-lzo verb 6 Server setting : port 1194 proto udp dev tun # the full paths to your server keys and certs ca /etc/openvpn/keys/ca.crt cert /etc/openvpn/keys/server.crt key /etc/openvpn/keys/server.key dh /etc/openvpn/keys/dh2048.pem cipher BF-CBC # Set server mode, and define a virtual pool of IP # addresses for clients to use. Use any subnet # that does not collide with your existing subnets. # In this example, the server can be pinged at 10.8.0.1 server 10.8.0.0 255.255.255.0 # Set up route(s) to subnet(s) behind # OpenVPN server push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" ifconfig-pool-persist /etc/openvpn/ipp.txt keepalive 10 120 status openvpn-status.log verb 6 and sysctl : net.ipv4.ip_forward=1 Thank you for your time and help.

  Read the article

• Connect from Mac OS X to Windows 7 Desktop

  - by jrn

  I am trying to connect from my MacBook to my Windows 7 machine within my own network - if it will work from outside my network that's a plus but no need to have. My Windows 7 machine is freshly installed with Windows 7 Home Premium. It runs the built-in firewall with no settings changed so far as well as Microsoft Security Essentials. So far I tried CoRD and Microsofts Remote Desktop Connections to connect from my Mac to my Windows machine without any success. I did try and disabled the firewall on my Windows machine but could not connect either. The reason I did this was to check wether there is a Windows firewall setting preventing me from connecting. On top of that I manually started the Remote Desktop Services and Remote Desktop Configuration within services.msc. Is there anything else I have to enable for a remote desktop connection? Could there be any router setting I have to tweak? Since I do not want to connect from outside my own network I thought I don't have to do any port forwarding. The error messages I retrieve are all connection timeouts. I can however ping the hostname and/or IP address. Any help would be greatly appreciated. Thanks a lot, jrn

  Read the article

• Using Openfire for distributed XMPP-based video-chat

  - by Yitzhak

  I have been tasked with setting up a distributed video-chat system built on XMPP. Currently my setup looks like this: Openfire (XMPP server) + JingleNodes plugin for video chat OpenLDAP (LDAP server) for storing user information and allowing directory queries Kerberos server for authentication and passwords In testing with one set of machines (i.e. only three), everything works as expected: I can log in to Openfire and it looks up the user information in the OpenLDAP database, which in turn authenticates my user with Kerberos. Now, I want to have several clusters, so that there is a cluster on each continent. A typical cluster will probably contain 2-5 servers. Users logging in will be directed to the closest cluster based on geographical location. Something that concerns me particularly is the dynamic maintenance of contact lists. If a user is using a machine in Asia, for example, how would contact lists be updated around the world to reflect the current server he is using? How would that work with LDAP? Specific questions: How do I direct users based on geographical location? What is the best architecture for a cluster? -- would all traffic need to come into a load-balancer on each one, for example? How do I manage the update of contact lists across all these servers? In general, how do I go about setting this up? What are the pitfalls in doing this? I am inexperienced in this area, so any advice and suggestions would be appreciated.

  Read the article

• How to turn off the display in Windows 8 without locking or making computer go to sleep?

  - by darshshah

  How to turn of the display in Windows 8 without locking or making computer go to sleep ? The problem is that when I enable ‘Turn off display after x minutes’ feature from control panel, the device goes into sleep after ‘x’ minutes. It seems that both the options – turn off display/put computer to sleep are connected. It devices goes automatically to sleep mode as soon as the display is turned off. So, is there any method to turn off the display of the device without it going into sleep mode ? Someone wrote in the microsoft forum " The whole key to this problem seems to be the "Turn off the Display" setting. If you have that set to 5 minutes, 10 minutes, 15 minutes, etc...the computer will go to sleep one minute after you lock the screen. With this setting set to "Never", it doesn't do it. So something is wrong there." I want to turnoff the display but don't want to lock the device. Is that also possible ? Thanks

  Read the article

• Configure Web app for external access (IIS7), allowing only certain users via AD group. All users need internal access

  - by White Island

  We have a Web app running in IIS7 (Server 2008 R2). I now need to allow external access with an SSL certificate, so certain users (e.g. the owner of the company) can use it remotely without VPN. They want to roll out the external access only to those specific users at first (thinking: a Windows credential prompt), BUT everyone will still need access internally (HTTP), without the prompt. I have the SSL cert installed on the server and public DNS configured. I've been trying to figure out how to work the authentication/authorization. I was thinking I need to disable Anonymous authn and set Windows authn, then I keep coming back to 'URL Authorization' in my research for the group setting; however, when I tried URL authz, (removed allow all, added allow rule for the special group), it broke the site internally (403.2 Forbidden, I believe it was). I thought maybe setting up a second site in IIS pointing to the same program would work, but the exact same thing happened (and again with a new app pool, just for kicks). So I guess my question is, how would you do this: allow external access, limited to users in a specific AD group, while still allowing internal access without a credentials prompt? How do I separate the external HTTPS and internal HTTP authorization requirements? Will I need to just copy the entire contents of the app in Windows Explorer to a new folder and create my external site from that? Is Windows authentication the correct option for this? I did come across this, which refers to creating a custom module. While it sounds like a solution, it's not one I'm familiar with, and I just wondered if there is a simpler way to get it to work: http://forums.iis.net/p/1182792/2000775.aspx Thanks!

  Read the article

• ?Exadata??????DBFS

  - by Liu Maclean(???)

  ?Exadata???DBFS ??????? 1. ??fuse RPM  [root@dm01db01 ~]# yum install fuse Loaded plugins: rhnplugin, security This system is not registered with ULN. ULN support will be disabled. Setting up Install Process Resolving Dependencies --> Running transaction check ---> Package fuse.x86_64 0:2.7.4-8.0.1.el5 set to be updated --> Finished Dependency Resolution Dependencies Resolved ========================================================================================================================================================================  Package                            Arch                                 Version                                         Repository                                Size ======================================================================================================================================================================== Installing:  fuse                               x86_64                               2.7.4-8.0.1.el5                                 el5_latest                                85 k Transaction Summary ======================================================================================================================================================================== Install       1 Package(s) Upgrade       0 Package(s) Total download size: 85 k Is this ok [y/N]: y Downloading Packages: fuse-2.7.4-8.0.1.el5.x86_64.rpm                                                                                                                  |  85 kB     00:00      Running rpm_check_debug Running Transaction Test Finished Transaction Test Transaction Test Succeeded Running Transaction   Installing     : fuse                                                                                                                                             1/1  Installed:   fuse.x86_64 0:2.7.4-8.0.1.el5                                                                                                                                          [root@dm01db01 ~]# yum install fuse-libs Loaded plugins: rhnplugin, security This system is not registered with ULN. ULN support will be disabled. Setting up Install Process Resolving Dependencies --> Running transaction check ---> Package fuse-libs.i386 0:2.7.4-8.0.1.el5 set to be updated ---> Package fuse-libs.x86_64 0:2.7.4-8.0.1.el5 set to be updated --> Finished Dependency Resolution Dependencies Resolved ========================================================================================================================================================================  Package                                Arch                                Version                                       Repository                               Size ======================================================================================================================================================================== Installing:  fuse-libs                              i386                                2.7.4-8.0.1.el5                               el5_latest                               71 k  fuse-libs                              x86_64                              2.7.4-8.0.1.el5                               el5_latest                               70 k Transaction Summary ======================================================================================================================================================================== Install       2 Package(s) Upgrade       0 Package(s) Total download size: 141 k Is this ok [y/N]: y Downloading Packages: (1/2): fuse-libs-2.7.4-8.0.1.el5.x86_64.rpm                                                                                                      |  70 kB     00:00      (2/2): fuse-libs-2.7.4-8.0.1.el5.i386.rpm                                                                                                        |  71 kB     00:00      ------------------------------------------------------------------------------------------------------------------------------------------------------------------------ Total                                                                                                                                    71 kB/s | 141 kB     00:01      Running rpm_check_debug Running Transaction Test Finished Transaction Test Transaction Test Succeeded Running Transaction   Installing     : fuse-libs                                                                                                                                        1/2    Installing     : fuse-libs                                                                                                                                        2/2  Installed:   fuse-libs.i386 0:2.7.4-8.0.1.el5                                                  fuse-libs.x86_64 0:2.7.4-8.0.1.el5                                                  Complete! [root@dm01db01 ~]# yum install fuse-devel Loaded plugins: rhnplugin, security This system is not registered with ULN. ULN support will be disabled. Setting up Install Process Resolving Dependencies --> Running transaction check ---> Package fuse-devel.i386 0:2.7.4-8.0.1.el5 set to be updated ---> Package fuse-devel.x86_64 0:2.7.4-8.0.1.el5 set to be updated --> Finished Dependency Resolution Dependencies Resolved ========================================================================================================================================================================  Package                                 Arch                                Version                                      Repository                               Size ======================================================================================================================================================================== Installing:  fuse-devel                              i386                                2.7.4-8.0.1.el5                              el5_latest                               28 k  fuse-devel                              x86_64                              2.7.4-8.0.1.el5                              el5_latest                               28 k Transaction Summary ======================================================================================================================================================================== Install       2 Package(s) Upgrade       0 Package(s) Total download size: 57 k Is this ok [y/N]: y Downloading Packages: (1/2): fuse-devel-2.7.4-8.0.1.el5.x86_64.rpm                                                                                                     |  28 kB     00:00      (2/2): fuse-devel-2.7.4-8.0.1.el5.i386.rpm                                                                                                       |  28 kB     00:00      ------------------------------------------------------------------------------------------------------------------------------------------------------------------------ Total                                                                                                                                    21 kB/s |  57 kB     00:02      Running rpm_check_debug Running Transaction Test Finished Transaction Test Transaction Test Succeeded Running Transaction   Installing     : fuse-devel                                                                                                                                       1/2    Installing     : fuse-devel                                                                                                                                       2/2  Installed:   fuse-devel.i386 0:2.7.4-8.0.1.el5                                                 fuse-devel.x86_64 0:2.7.4-8.0.1.el5                                                 Complete! 2. ?? DBFS??? ?????? cd $ORACLE_HOME/rdbms/admin sqlplus / as sysdba Oracle Database 11g Enterprise Edition Release 11.2.0.3.0 - 64bit Production With the Partitioning, Real Application Clusters, Automatic Storage Management, OLAP, Data Mining and Real Application Testing options SQL> @prvtfspi.plb Package body created. No errors. Package body created. No errors. ?????dbms_dbfs_sfs package  SQL> create tablespace dbfstbs datafile size 20g; Tablespace created. SQL> create user maclean_dbfs identified by oracle; User created. SQL> grant dba to maclean_dbfs; Grant succeeded. @@!!! SQL> grant  dbfs_role to maclean_dbfs; Grant succeeded. 3. ??DBFS SQL> conn maclean_dbfs/oracle Connected. SQL> @?/rdbms/admin/dbfs_create_filesystem.sql  dbfstbs mac_dbfs   No errors. -------- CREATE STORE: begin dbms_dbfs_sfs.createFilesystem(store_name => 'FS_MAC_DBFS', tbl_name => 'T_MAC_DBFS', tbl_tbs => 'dbfstbs', lob_tbs => 'dbfstbs', do_partition => false, partition_key => 1, do_compress => false, compression => '', do_dedup => false, do_encrypt => false); end; -------- REGISTER STORE: begin dbms_dbfs_content.registerStore(store_name=> 'FS_MAC_DBFS', provider_name => 'sample1', provider_package => 'dbms_dbfs_sfs'); end; -------- MOUNT STORE: begin dbms_dbfs_content.mountStore(store_name=>'FS_MAC_DBFS', store_mount=>'mac_dbfs'); end; -------- CHMOD STORE: declare m integer; begin m := dbms_fuse.fs_chmod('/mac_dbfs', 16895); end; No errors. 4.  ??mount point  [root@dm01db01 ~]# mkdir /dbfs [root@dm01db01 ~]# chown oracle:oinstall /dbfs 5. ??library path ?OS  # echo "/usr/local/lib" >> /etc/ld.so.conf.d/usr_local_lib.conf 6. ?????? export ORACLE_HOME=/s01/orabase/product/11.2.0/dbhome_1 [root@dm01db01 ~]# ln -s $ORACLE_HOME/lib/libclntsh.so.11.1 /usr/local/lib/libclntsh.so.11.1 [root@dm01db01 ~]#  ln -s $ORACLE_HOME/lib/libnnz11.so /usr/local/lib/libnnz11.so [root@dm01db01 ~]#  ln -s /lib64/libfuse.so.2 /usr/local/lib/libfuse.so.2 7. ??ldconfig  [root@dm01db01 ~]# ldconfig [root@dm01db01 ~]#  8. ??fusermount??????? [root@dm01db01 ~]#  chmod +x /usr/bin/fusermount [root@dm01db01 ~]#  ls -l /usr/bin/fusermount lrwxrwxrwx 1 root root 15 Sep  7 03:06 /usr/bin/fusermount -> /bin/fusermount [root@dm01db01 ~]#  ls -l /bin/fusermount -rwsr-x--x 1 root fuse 27072 Oct 17  2011 /bin/fusermount 9. ???????OS  dbfs_client maclean_dbfs@dm01db01:1521/orcl  /dbfs 10. ????nohup + &?????mount DBFS,???????????? [oracle@dm01db01 ~]$ echo "oracle"  >> dbfs_pw [oracle@dm01db01 ~]$ nohup dbfs_client maclean_dbfs@dm01db01:1521/orcl /dbfs < dbfs_pw & [oracle@dm01db01 ~]$ df -h Filesystem            Size  Used Avail Use% Mounted on /dev/mapper/VGExaDb-LVDbSys1                        30G   15G   14G  53% / /dev/sda1             502M   30M  447M   7% /boot /dev/mapper/VGExaDb-LVDbOra1                        99G   20G   75G  21% /u01 tmpfs                  81G     0   81G   0% /dev/shm dbfs-maclean_dbfs@orcl:/                        20G  120K   20G   1% /dbfs [oracle@dm01db01 ~]$ mount /dev/mapper/VGExaDb-LVDbSys1 on / type ext3 (rw) proc on /proc type proc (rw) sysfs on /sys type sysfs (rw) devpts on /dev/pts type devpts (rw,gid=5,mode=620) /dev/sda1 on /boot type ext3 (rw,nodev) /dev/mapper/VGExaDb-LVDbOra1 on /u01 type ext3 (rw,nodev) tmpfs on /dev/shm type tmpfs (rw,size=82052m) none on /proc/sys/fs/binfmt_misc type binfmt_misc (rw) dbfs-maclean_dbfs@orcl:/ on /dbfs type fuse (rw,nosuid,nodev,max_read=1048576,default_permissions,user=oracle) [oracle@dm01db01 ~]$ ls -l /dbfs/ total 0 drwxrwxrwx 3 root root 0 Sep 14 05:11 mac_dbfs [oracle@nas ~]$ dbfs_client  --------MOUNT mode: usage: dbfs_client <db_user>@<db_server> [options] <mountpoint>   db_user:              Name of Database user that owns DBFS content repository filesystem(s)   db_server:            A valid connect string for Oracle database server                         (for example, hrdb_host:1521/hrservice)   mountpoint:           Path to mount Database File System(s)                         All the file systems owned by the database user will be seen at the mountpoint. DBFS options:   -o direct_io          Bypass the Linux page cache. Gives much better performance for large files.                         Programs in the file system cannot be executed with this option.                         This option is recommended when DBFS is used as an ETL staging area.   -o wallet             Run dbfs_client in background.                         Wallet must be configured to get credentials.   -o failover           dbfs_client fails over to surviving database instance with no data loss.                         Some performance cost on writes, especially for small files.   -o allow_root         Allows root access to the filesystem.                         This option requires setting 'user_allow_other' parameter in '/etc/fuse.conf'.   -o allow_other        Allows other users access to the file system.                         This option requires setting 'user_allow_other' parameter in '/etc/fuse.conf'.   -o rw                 Mount the filesystem read-write. [Default]   -o ro                 Mount the filesystem read-only. Files cannot be modified.   -o trace_file=STR     Tracing <filename> | 'syslog'   -o trace_level=N      Trace Level: 1->DEBUG, 2->INFO, 3->WARNING, 4->ERROR, 5->CRITICAL [Default: 4]   -h                    help   -V                    version --------COMMAND mode: Usage:     dbfs_client <db_user>@<db_server> --command command [switches] [arguments]             command:          Command to be executed, e.g., ls, cp, mkdir, rm            switches:         Switches are described below for each command.            arguments:        File names or directory names NOTE:      All database pathnames must be absolute and preceded by dbfs:/ Commands   ls            dbfs_client <db_user>@<db_server> --command ls [switches] target      Switches:              -a         Show all files including those starting with '.'            -l         Use a long listing format. In addition to the name of each file                       print the file type, permissions, size, user and group information            -R         List subdirectories recursively cp                     dbfs_client <db_user>@<db_server> --command cp [switches] source destination      Switches:              -r, -R      Copy a directory and its contents recursively into the destination directory rm                     dbfs_client <db_user>@<db_server> --command rm [switches] target      Switches:              -r, -R      Removes a directory and its contents recursively mkdir                  dbfs_client <db_user>@<db_server> --command mkdir directory_name Examples                     dbfs_client ETLUser@DBConnectString --command ls -l -a dbfs:/staging_area/directory1            dbfs_client ETLUser@DBConnectString --command cp -R  /tmp/1-Jan-2009-dump dbfs:/staging_area            dbfs_client ETLUser@DBConnectString --command rm dbfs:/staging_area/hello.txt            dbfs_client ETLUser@DBConnectString --command mkdir dbfs:/staging_area/directory2 [oracle@dm01db01 ~]$ ls -lh /tmp/largefile -rw-r--r-- 1 oracle oinstall 2.0G Sep 14 08:50 /tmp/largefile [oracle@dm01db01 ~]$ time dbfs_client  maclean_dbfs@dm01db01:1521/orcl --command cp /tmp/largefile dbfs:/mac_dbfs Password: /tmp/largefile -> dbfs:/mac_dbfs/largefile real    0m11.802s user    0m0.580s sys     0m2.375s ?Exadata?????2G?????? DBFS???11s => 200MB/s 

  Read the article

• Connecting to SQL Server in Php - Extension Err

  - by John Doe

  <html> <head> <title>Connecting </title> </head> <body> <?php $host = "*.*.*.*"; $username = "xxx"; $password = "xxx"; $db_name = "xxx"; $db = mssql_connect($host, $username,$password) or die("Couldnt Connect"); $selected = mssql_select_db($db_name, $db) or die("Couldnt open database"); ?> </body> </html> My error message is: Fatal error: Call to undefined function mssql_connect() in C:\wamp\www\php\dbase.php on line 12 I am using WampServer 2.0 on Php 5.3.0 When I check the extensions, php_mssql is Checked. I also checked the php.ini file to make sure it is not commented out. I have my file dbase.php saved in C:\wamp\www\php. I have tried stopping the service, closing everything, and running it again. I know the problem is that the extension file is not being included somehow. The below is copied from my php.ini file. Note I made all http = /http to avoid posting Links. ;;;;;;;;;;;;;;;;;;;;;;;;; ; Paths and Directories ; ;;;;;;;;;;;;;;;;;;;;;;;;; ; UNIX: "/path1:/path2" ;include_path = ".:/php/includes" ; Windows: "\path1;\path2" include_path = "C:\wamp\bin\php\php5.3.0\ext" ; ; PHP's default setting for include_path is ".;/path/to/php/pear" ; /http://php.net/include-path ; The root of the PHP pages, used only if nonempty. ; if PHP was not compiled with FORCE_REDIRECT, you SHOULD set doc_root ; if you are running php as a CGI under any web server (other than IIS) ; see documentation for security issues. The alternate is to use the ; cgi.force_redirect configuration below ; /http://php.net/doc-root doc_root = ; The directory under which PHP opens the script using /~username used only ; if nonempty. ; /http://php.net/user-dir user_dir = ; Directory in which the loadable extensions (modules) reside. ; /http://php.net/extension-dir ; extension_dir = "./" ; On windows: ; extension_dir = "ext" extension_dir = "c:/wamp/bin/php/php5.3.0/ext/" ; Whether or not to enable the dl() function. The dl() function does NOT work ; properly in multithreaded servers, such as IIS or Zeus, and is automatically ; disabled on them. ; /http://php.net/enable-dl enable_dl = Off ; cgi.force_redirect is necessary to provide security running PHP as a CGI under ; most web servers. Left undefined, PHP turns this on by default. You can ; turn it off here AT YOUR OWN RISK ; You CAN safely turn this off for IIS, in fact, you MUST. ; /http://php.net/cgi.force-redirect ;cgi.force_redirect = 1 ; if cgi.nph is enabled it will force cgi to always sent Status: 200 with ; every request. PHP's default behavior is to disable this feature. ;cgi.nph = 1 ; if cgi.force_redirect is turned on, and you are not running under Apache or Netscape ; (iPlanet) web servers, you MAY need to set an environment variable name that PHP ; will look for to know it is OK to continue execution. Setting this variable MAY ; cause security issues, KNOW WHAT YOU ARE DOING FIRST. ; /http://php.net/cgi.redirect-status-env ;cgi.redirect_status_env = ; ; cgi.fix_pathinfo provides real PATH_INFO/PATH_TRANSLATED support for CGI. PHP's ; previous behaviour was to set PATH_TRANSLATED to SCRIPT_FILENAME, and to not grok ; what PATH_INFO is. For more information on PATH_INFO, see the cgi specs. Setting ; this to 1 will cause PHP CGI to fix its paths to conform to the spec. A setting ; of zero causes PHP to behave as before. Default is 1. You should fix your scripts ; to use SCRIPT_FILENAME rather than PATH_TRANSLATED. ; /http://php.net/cgi.fix-pathinfo ;cgi.fix_pathinfo=1 ; FastCGI under IIS (on WINNT based OS) supports the ability to impersonate ; security tokens of the calling client. This allows IIS to define the ; security context that the request runs under. mod_fastcgi under Apache ; does not currently support this feature (03/17/2002) ; Set to 1 if running under IIS. Default is zero. ; /http://php.net/fastcgi.impersonate ;fastcgi.impersonate = 1; ; Disable logging through FastCGI connection. PHP's default behavior is to enable ; this feature. ;fastcgi.logging = 0 ; cgi.rfc2616_headers configuration option tells PHP what type of headers to ; use when sending HTTP response code. If it's set 0 PHP sends Status: header that ; is supported by Apache. When this option is set to 1 PHP will send ; RFC2616 compliant header. ; Default is zero. ; /http://php.net/cgi.rfc2616-headers ;cgi.rfc2616_headers = 0 ;;;;;;;;;;;;;;;; ; File Uploads ; ;;;;;;;;;;;;;;;; ; Whether to allow HTTP file uploads. ; /http://php.net/file-uploads file_uploads = On ; Temporary directory for HTTP uploaded files (will use system default if not ; specified). ; /http://php.net/upload-tmp-dir upload_tmp_dir = "c:/wamp/tmp" ; Maximum allowed size for uploaded files. ; /http://php.net/upload-max-filesize upload_max_filesize = 2M Also, my php.ini file is saved in: C:\wamp\bin\apache\Apache2.2.11\bin

  Read the article

• Connecting to mssql in Php - Extension Err

  - by John Doe

  <html> <head> <title>Connecting </title> </head> <body> <?php $host = "*.*.*.*"; $username = "xxx"; $password = "xxx"; $db_name = "xxx"; $db = mssql_connect($host, $username,$password) or die("Couldnt Connect"); $selected = mssql_select_db($db_name, $db) or die("Couldnt open database"); ?> </body> </html> My error message is: Fatal error: Call to undefined function mssql_connect() in C:\wamp\www\php\dbase.php on line 12 I am using WampServer 2.0 on Php 5.3.0 When I check the extensions, php_mssql is Checked. I also checked the php.ini file to make sure it is not commented out. I have my file dbase.php saved in C:\wamp\www\php. I have tried stopping the service, closing everything, and running it again. I know the problem is that the extension file is not being included somehow. The below is copied from my php.ini file. Note I made all http = /http to avoid posting Links. ;;;;;;;;;;;;;;;;;;;;;;;;; ; Paths and Directories ; ;;;;;;;;;;;;;;;;;;;;;;;;; ; UNIX: "/path1:/path2" ;include_path = ".:/php/includes" ; Windows: "\path1;\path2" include_path = "C:\wamp\bin\php\php5.3.0\ext" ; ; PHP's default setting for include_path is ".;/path/to/php/pear" ; /http://php.net/include-path ; The root of the PHP pages, used only if nonempty. ; if PHP was not compiled with FORCE_REDIRECT, you SHOULD set doc_root ; if you are running php as a CGI under any web server (other than IIS) ; see documentation for security issues. The alternate is to use the ; cgi.force_redirect configuration below ; /http://php.net/doc-root doc_root = ; The directory under which PHP opens the script using /~username used only ; if nonempty. ; /http://php.net/user-dir user_dir = ; Directory in which the loadable extensions (modules) reside. ; /http://php.net/extension-dir ; extension_dir = "./" ; On windows: ; extension_dir = "ext" extension_dir = "c:/wamp/bin/php/php5.3.0/ext/" ; Whether or not to enable the dl() function. The dl() function does NOT work ; properly in multithreaded servers, such as IIS or Zeus, and is automatically ; disabled on them. ; /http://php.net/enable-dl enable_dl = Off ; cgi.force_redirect is necessary to provide security running PHP as a CGI under ; most web servers. Left undefined, PHP turns this on by default. You can ; turn it off here AT YOUR OWN RISK ; You CAN safely turn this off for IIS, in fact, you MUST. ; /http://php.net/cgi.force-redirect ;cgi.force_redirect = 1 ; if cgi.nph is enabled it will force cgi to always sent Status: 200 with ; every request. PHP's default behavior is to disable this feature. ;cgi.nph = 1 ; if cgi.force_redirect is turned on, and you are not running under Apache or Netscape ; (iPlanet) web servers, you MAY need to set an environment variable name that PHP ; will look for to know it is OK to continue execution. Setting this variable MAY ; cause security issues, KNOW WHAT YOU ARE DOING FIRST. ; /http://php.net/cgi.redirect-status-env ;cgi.redirect_status_env = ; ; cgi.fix_pathinfo provides real PATH_INFO/PATH_TRANSLATED support for CGI. PHP's ; previous behaviour was to set PATH_TRANSLATED to SCRIPT_FILENAME, and to not grok ; what PATH_INFO is. For more information on PATH_INFO, see the cgi specs. Setting ; this to 1 will cause PHP CGI to fix its paths to conform to the spec. A setting ; of zero causes PHP to behave as before. Default is 1. You should fix your scripts ; to use SCRIPT_FILENAME rather than PATH_TRANSLATED. ; /http://php.net/cgi.fix-pathinfo ;cgi.fix_pathinfo=1 ; FastCGI under IIS (on WINNT based OS) supports the ability to impersonate ; security tokens of the calling client. This allows IIS to define the ; security context that the request runs under. mod_fastcgi under Apache ; does not currently support this feature (03/17/2002) ; Set to 1 if running under IIS. Default is zero. ; /http://php.net/fastcgi.impersonate ;fastcgi.impersonate = 1; ; Disable logging through FastCGI connection. PHP's default behavior is to enable ; this feature. ;fastcgi.logging = 0 ; cgi.rfc2616_headers configuration option tells PHP what type of headers to ; use when sending HTTP response code. If it's set 0 PHP sends Status: header that ; is supported by Apache. When this option is set to 1 PHP will send ; RFC2616 compliant header. ; Default is zero. ; /http://php.net/cgi.rfc2616-headers ;cgi.rfc2616_headers = 0 ;;;;;;;;;;;;;;;; ; File Uploads ; ;;;;;;;;;;;;;;;; ; Whether to allow HTTP file uploads. ; /http://php.net/file-uploads file_uploads = On ; Temporary directory for HTTP uploaded files (will use system default if not ; specified). ; /http://php.net/upload-tmp-dir upload_tmp_dir = "c:/wamp/tmp" ; Maximum allowed size for uploaded files. ; /http://php.net/upload-max-filesize upload_max_filesize = 2M Also, my php.ini file is saved in: C:\wamp\bin\apache\Apache2.2.11\bin

  Read the article

• Remotely Schedule and Stream Recorded TV in Windows 7 Media Center

  - by DigitalGeekery

  Have you ever been away from home and suddenly realized you forgot to record your favorite program? Now Windows 7 Media Center, users can schedule recordings remotely from their phones or mobile devices with Remote Potato. How it Works Remote Potato installs server software on the host computer running Windows 7 Media Center. Once the software is installed, we’ll need to do some port forwarding on the router and setup an optional dynamic DNS address. When setup is completed, we will access the application through a web based interface. Silverlight is required for Streaming recorded TV, but scheduling recordings can be done through an HTML interface. Installing Remote Potato Download and install Remote Potato on the Media Center PC. (See download link below) If you plan to stream any Recorded TV, you’ll also want to install the streaming pack located on the same page. It isn’t required to stream all shows, only shows that require the AC3 audio codec. Click Yes to allow Remote Potato to add rules to the Windows Firewall for remote access. You’ll likely need to accept a few UAC prompts. When notified that the rules were added, click OK. Remote Potato will then prompt you to allow administrator privileges to reserve a URL for it’s web server. Click Yes. Remote Potato server will start. Click on the configuration button at the right to to reveal the settings tabs.   One the General tab, you’ll have the option to run Remote Potato on startup and minimized in the System Tray. If you’re running Media Center on a dedicated HTPC, you’ll probably want to enable both startup options. Forwarding Ports on Your Router You’ll need to forward a couple ports on your router. By default, these will be ports 9080 and 9081. In this example we’re using a Linksys WRT54GL router, however, the steps for port forwarding will vary from router to router. On the Linksys configuration page, click on the Applications & Gaming Tab, and then the Port Range Forward tab. Under Application, type in a name of your choosing. In both the Start and End boxes, type the port number 9080. Enter the local IP address of your Media Center computer in the IP address column. Click the check box under Enable. Repeat the process on the next line, but this time use port 9081. When finished, click the Save Settings button. Note: It’s highly recommended that you configure the home computer running Media Center & Remote Potato with a static IP address.   Find your IP Address You’ll need to find the IP address assigned to your router from your ISP. There are many ways to do this but a quick and easy way is to visit a site like checkip.dyndns.org (link available below) The current external IP address of your router will be displayed in the browser.   Dynamic DNS This is an optional step, but  it’s highly recommended. Many routers, such as the Linksys WRT54GL we are using, support Dynamic DNS (DDNS). What Dynamic DNS allows you to do is affiliate your home router’s external IP address to a domain name. Every time your home router is assigned a a new IP address by your ISP, the domain name is updated to point to your new IP address. Remote Potato’s user interface is accessed over the Internet is by connecting to your router’s IP address followed by a colon and the port number. (Ex: XXX.XXX.XXX.XXX:9080) Instead of constantly having to look up and remember an IP address, you can use DDNS along with a 3rd party provider like DynDNS.com, to sign up for a free domain name and configure it to be updated each time your router is assigned a new IP address. Go to the DynDNS.com website (See link at the end of the article) and sign up for a free Domain name. You’ll need to register and confirm by email.   Once you’ve signed in and selected your domain name click Activate Services. You’ll get a confirmation message that your domain name has been activated.    On the Linksys WRT54GL click on the Setup tab an then DDNS. Select DynDNS.org, or TZO.com if you prefer to use their service, from the drop down list.   With DynDNS, you’ll need to fill in your username and password you signed up with at the DynDNS website and the hostname you chose. Note: You can connect over your local network with the IP Address of the computer running Remote Potato followed by a colon and the port number. Ex: 192.168.1.2:9080 Logging in Remote Potato and Recording a Show Once you connect, you’ll see the start page. To view the TV listings, click on TV Guide. You’ll then see your guide listings. There are a few ways to navigate the listings. At the top left, you can click on any of the preset time buttons to jump to  the listings at that time of the day.  Click on the arrows to the right and left of the day and date at the top center to proceed to the previous or next day. Or, jump to a specific day with the date and date buttons at the top right.   To setup a recording, click on a program.   You can choose to record the individual show or the entire series by clicking on Record Show or Record Series.   Remote Potato on Mobile Devices Perhaps the coolest feature of Remote Potato is the ability to schedule recording from your phone or mobile device. Note: For any devices or computers without Silverlight, you will be prompted to view the HTML page. Select Browse Listings. Select your program to record. In the Program Details, select Record Show to record the single episode or Record Series to record all instances of the series. You will then see a red dot on the program listing to indicate that the show is scheduled for recording.   Streaming Recorded TV Click on Recorded TV from the home screen to access your previously recorded TV programs. Click on the selection you wish to stream. Click on Play. If you receive this error message, you’ll need to install the streaming pack for Remote Potato. This is found on the same download page as installation files. (See link below) The Begin from slider allows you to start playback from the start (by default) or a different time of the program by moving the slider. The Quality (bitrate) setting  allows you to choose the quality of the playback. We found the video quality on the Normal setting to be pretty lousy, and Low was just pointless. High was the best overall viewing experience as it provided smooth quality video playback. We experienced significant stuttering during playback using the Ultra High setting.   Click Start when you are ready to begin. When playback begins you’ll see a slider at the top right.   Move the slider left or right to increase or decrease the size of the video. There’s also a button to switch to full screen.   Media Center users who travel frequently or are always on the go will likely find Remote Potato to be a blessing. Since being released earlier this year, updates for Remote Potato have come fast and furious. The latest beta release includes support for streaming music and photos. If you like those nice network TV logos, check out our article on adding TV channel logos to Windows Media Center. Downloads and Links Download Remote Potato and Streaming Pack Find your IP address Sign Up for a Domain Name at DynDNS.com Similar Articles Productive Geek Tips Schedule Updates for Windows Media CenterUsing Netflix Watchnow in Windows Vista Media Center (Gmedia)Add a Sleep Timer to Windows 7 Media CenterStartup Customizations for Media Center in Windows 7Enable Media Streaming in Windows Home Server to Windows Media Player TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 FoxClocks adds World Times in your Statusbar (Firefox) Have Fun Editing Photo Editing with Citrify Outlook Connector Upgrade Error Gadfly is a cool Twitter/Silverlight app Enable DreamScene in Windows 7 Microsoft’s “How Do I ?” Videos

  Read the article

• Creating a dynamic proxy generator with c# – Part 4 – Calling the base method

  - by SeanMcAlinden

  Creating a dynamic proxy generator with c# – Part 1 – Creating the Assembly builder, Module builder and caching mechanism Creating a dynamic proxy generator with c# – Part 2 – Interceptor Design Creating a dynamic proxy generator with c# – Part 3 – Creating the constructors   The plan for calling the base methods from the proxy is to create a private method for each overridden proxy method, this will allow the proxy to use a delegate to simply invoke the private method when required. Quite a few helper classes have been created to make this possible so as usual I would suggest download or viewing the code at http://rapidioc.codeplex.com/. In this post I’m just going to cover the main points for when creating methods. Getting the methods to override The first two notable methods are for getting the methods. private static MethodInfo[] GetMethodsToOverride<TBase>() where TBase : class {     return typeof(TBase).GetMethods().Where(x =>         !methodsToIgnore.Contains(x.Name) &&                              (x.Attributes & MethodAttributes.Final) == 0)         .ToArray(); } private static StringCollection GetMethodsToIgnore() {     return new StringCollection()     {         "ToString",         "GetHashCode",         "Equals",         "GetType"     }; } The GetMethodsToIgnore method string collection contains an array of methods that I don’t want to override. In the GetMethodsToOverride method, you’ll notice a binary AND which is basically saying not to include any methods marked final i.e. not virtual. Creating the MethodInfo for calling the base method This method should hopefully be fairly easy to follow, it’s only function is to create a MethodInfo which points to the correct base method, and with the correct parameters. private static MethodInfo CreateCallBaseMethodInfo<TBase>(MethodInfo method) where TBase : class {     Type[] baseMethodParameterTypes = ParameterHelper.GetParameterTypes(method, method.GetParameters());       return typeof(TBase).GetMethod(        method.Name,        BindingFlags.Instance | BindingFlags.Public | BindingFlags.NonPublic,        null,        baseMethodParameterTypes,        null     ); }   /// <summary> /// Get the parameter types. /// </summary> /// <param name="method">The method.</param> /// <param name="parameters">The parameters.</param> public static Type[] GetParameterTypes(MethodInfo method, ParameterInfo[] parameters) {     Type[] parameterTypesList = Type.EmptyTypes;       if (parameters.Length > 0)     {         parameterTypesList = CreateParametersList(parameters);     }     return parameterTypesList; }   Creating the new private methods for calling the base method The following method outline how I’ve created the private methods for calling the base class method. private static MethodBuilder CreateCallBaseMethodBuilder(TypeBuilder typeBuilder, MethodInfo method) {     string callBaseSuffix = "GetBaseMethod";       if (method.IsGenericMethod || method.IsGenericMethodDefinition)     {                         return MethodHelper.SetUpGenericMethod             (                 typeBuilder,                 method,                 method.Name + callBaseSuffix,                 MethodAttributes.Private | MethodAttributes.HideBySig             );     }     else     {         return MethodHelper.SetupNonGenericMethod             (                 typeBuilder,                 method,                 method.Name + callBaseSuffix,                 MethodAttributes.Private | MethodAttributes.HideBySig             );     } } The CreateCallBaseMethodBuilder is the entry point method for creating the call base method. I’ve added a suffix to the base classes method name to keep it unique. Non Generic Methods Creating a non generic method is fairly simple public static MethodBuilder SetupNonGenericMethod(     TypeBuilder typeBuilder,     MethodInfo method,     string methodName,     MethodAttributes methodAttributes) {     ParameterInfo[] parameters = method.GetParameters();       Type[] parameterTypes = ParameterHelper.GetParameterTypes(method, parameters);       Type returnType = method.ReturnType;       MethodBuilder methodBuilder = CreateMethodBuilder         (             typeBuilder,             method,             methodName,             methodAttributes,             parameterTypes,             returnType         );       ParameterHelper.SetUpParameters(parameterTypes, parameters, methodBuilder);       return methodBuilder; }   private static MethodBuilder CreateMethodBuilder (     TypeBuilder typeBuilder,     MethodInfo method,     string methodName,     MethodAttributes methodAttributes,     Type[] parameterTypes,     Type returnType ) { MethodBuilder methodBuilder = typeBuilder.DefineMethod(methodName, methodAttributes, returnType, parameterTypes); return methodBuilder; } As you can see, you simply have to declare a method builder, get the parameter types, and set the method attributes you want.   Generic Methods Creating generic methods takes a little bit more work. /// <summary> /// Sets up generic method. /// </summary> /// <param name="typeBuilder">The type builder.</param> /// <param name="method">The method.</param> /// <param name="methodName">Name of the method.</param> /// <param name="methodAttributes">The method attributes.</param> public static MethodBuilder SetUpGenericMethod     (         TypeBuilder typeBuilder,         MethodInfo method,         string methodName,         MethodAttributes methodAttributes     ) {     ParameterInfo[] parameters = method.GetParameters();       Type[] parameterTypes = ParameterHelper.GetParameterTypes(method, parameters);       MethodBuilder methodBuilder = typeBuilder.DefineMethod(methodName,         methodAttributes);       Type[] genericArguments = method.GetGenericArguments();       GenericTypeParameterBuilder[] genericTypeParameters =         GetGenericTypeParameters(methodBuilder, genericArguments);       ParameterHelper.SetUpParameterConstraints(parameterTypes, genericTypeParameters);       SetUpReturnType(method, methodBuilder, genericTypeParameters);       if (method.IsGenericMethod)     {         methodBuilder.MakeGenericMethod(genericArguments);     }       ParameterHelper.SetUpParameters(parameterTypes, parameters, methodBuilder);       return methodBuilder; }   private static GenericTypeParameterBuilder[] GetGenericTypeParameters     (         MethodBuilder methodBuilder,         Type[] genericArguments     ) {     return methodBuilder.DefineGenericParameters(GenericsHelper.GetArgumentNames(genericArguments)); }   private static void SetUpReturnType(MethodInfo method, MethodBuilder methodBuilder, GenericTypeParameterBuilder[] genericTypeParameters) {     if (method.IsGenericMethodDefinition)     {         SetUpGenericDefinitionReturnType(method, methodBuilder, genericTypeParameters);     }     else     {         methodBuilder.SetReturnType(method.ReturnType);     } }   private static void SetUpGenericDefinitionReturnType(MethodInfo method, MethodBuilder methodBuilder, GenericTypeParameterBuilder[] genericTypeParameters) {     if (method.ReturnType == null)     {         methodBuilder.SetReturnType(typeof(void));     }     else if (method.ReturnType.IsGenericType)     {         methodBuilder.SetReturnType(genericTypeParameters.Where             (x => x.Name == method.ReturnType.Name).First());     }     else     {         methodBuilder.SetReturnType(method.ReturnType);     }             } Ok, there are a few helper methods missing, basically there is way to much code to put in this post, take a look at the code at http://rapidioc.codeplex.com/ to follow it through completely. Basically though, when dealing with generics there is extra work to do in terms of getting the generic argument types setting up any generic parameter constraints setting up the return type setting up the method as a generic All of the information is easy to get via reflection from the MethodInfo.   Emitting the new private method Emitting the new private method is relatively simple as it’s only function is calling the base method and returning a result if the return type is not void. ILGenerator il = privateMethodBuilder.GetILGenerator();   EmitCallBaseMethod(method, callBaseMethod, il);   private static void EmitCallBaseMethod(MethodInfo method, MethodInfo callBaseMethod, ILGenerator il) {     int privateParameterCount = method.GetParameters().Length;       il.Emit(OpCodes.Ldarg_0);       if (privateParameterCount > 0)     {         for (int arg = 0; arg < privateParameterCount; arg++)         {             il.Emit(OpCodes.Ldarg_S, arg + 1);         }     }       il.Emit(OpCodes.Call, callBaseMethod);       il.Emit(OpCodes.Ret); } So in the main method building method, an ILGenerator is created from the method builder. The ILGenerator performs the following actions: Load the class (this) onto the stack using the hidden argument Ldarg_0. Create an argument on the stack for each of the method parameters (starting at 1 because 0 is the hidden argument) Call the base method using the Opcodes.Call code and the MethodInfo we created earlier. Call return on the method   Conclusion Now we have the private methods prepared for calling the base method, we have reached the last of the relatively easy part of the proxy building. Hopefully, it hasn’t been too hard to follow so far, there is a lot of code so I haven’t been able to post it all so please check it out at http://rapidioc.codeplex.com/. The next section should be up fairly soon, it’s going to cover creating the delegates for calling the private methods created in this post.   Kind Regards, Sean.

  Read the article

• SQL Server and Hyper-V Dynamic Memory Part 2

  - by SQLOS Team

  Part 1 of this series was an introduction and overview of Hyper-V Dynamic Memory. This part looks at SQL Server memory management and how the SQL engine responds to changing OS memory conditions.   Part 2: SQL Server Memory Management As with any Windows process, sqlserver.exe has a virtual address space (VAS) of 4GB on 32-bit and 8TB in 64-bit editions. Pages in its VAS are mapped to pages in physical memory when the memory is committed and referenced for the first time. The collection of VAS pages that have been recently referenced is known as the Working Set. How and when SQL Server allocates virtual memory and grows its working set depends on the memory model it uses. SQL Server supports three basic memory models:   1. Conventional Memory Model   The Conventional model is the default SQL Server memory model and has the following properties: - Dynamic - can grow or shrink its working set in response to load and external (operating system) memory conditions. - OS uses 4K pages – (not to be confused with SQL Server “pages” which are 8K regions of committed memory).- Pageable - Can be paged out to disk by the operating system.   2. Locked Page Model The locked page memory model is set when SQL Server is started with "Lock Pages in Memory" privilege*. It has the following characteristics: - Dynamic - can grow or shrink its working set in the same way as the Conventional model.- OS uses 4K pages - Non-Pageable – When memory is committed it is locked in memory, meaning that it will remain backed by physical memory and will not be paged out by the operating system. A common misconception is to interpret "locked" as non-dynamic. A SQL Server instance using the locked page memory model will grow and shrink (allocate memory and release memory) in response to changing workload and OS memory conditions in the same way as it does with the conventional model.   This is an important consideration when we look at Hyper-V Dynamic Memory – “locked” memory works perfectly well with “dynamic” memory.   * Note in “Denali” (Standard Edition and above), and in SQL 2008 R2 64-bit (Enterprise and above editions) the Lock Pages in Memory privilege is all that is required to set this model. In 2008 R2 64-Bit standard edition it also requires trace flag 845 to be set, in 2008 R2 32-bit editions it requires sp_configure 'awe enabled' 1.   3. Large Page Model The Large page model is set using trace flag 834 and potentially offers a small performance boost for systems that are configured with large pages. It is characterized by: - Static - memory is allocated at startup and does not change. - OS uses large (>2MB) pages - Non-Pageable The large page model is supported with Hyper-V Dynamic Memory (and Hyper-V also supports large pages), but you get no benefit from using Dynamic Memory with this model since SQL Server memory does not grow or shrink. The rest of this article will focus on the locked and conventional SQL Server memory models.   When does SQL Server grow? For “dynamic” configurations (Conventional and Locked memory models), the sqlservr.exe process grows – allocates and commits memory from the OS – in response to a workload. As much memory is allocated as is required to optimally run the query and buffer data for future queries, subject to limitations imposed by:   - SQL Server max server memory setting. If this configuration option is set, the buffer pool is not allowed to grow to more than this value. In SQL Server 2008 this value represents single page allocations, and in “Denali” it represents any size page allocations and also managed CLR procedure allocations.   - Memory signals from OS. The operating system sets a signal on memory resource notification objects to indicate whether it has memory available or whether it is low on available memory. If there is only 32MB free for every 4GB of memory a low memory signal is set, which continues until 64MB/4GB is free. If there is 96MB/4GB free the operating system sets a high memory signal. SQL Server only allocates memory when the high memory signal is set.   To summarize, for SQL Server to grow you need three conditions: a workload, max server memory setting higher than the current allocation, high memory signals from the OS.    When does SQL Server shrink caches? SQL Server as a rule does not like to return memory to the OS, but it will shrink its caches in response to memory pressure. Memory pressure can be divided into “internal” and “external”.   - External memory pressure occurs when the operating system is running low on memory and low memory signals are set. The SQL Server Resource Monitor checks for low memory signals approximately every 5 seconds and it will attempt to free memory until the signals stop.   To free memory SQL Server does the following: ·         Frees unused memory. ·         Notifies Memory Manager Clients to release memory o   Caches – Free unreferenced cache objects. o   Buffer pool - Based on oldest access times.   The freed memory is released back to the operating system. This process continues until the low memory resource notifications stop.    - Internal memory pressure occurs when the size of different caches and allocations increase but the SQL Server process needs to keep its total memory within a target value. For example if max server memory is set and certain caches are growing large, it will cause SQL to free memory for re-use internally, but not to release memory back to the OS. If you lower the value of max server memory you will generate internal memory pressure that will cause SQL to release memory back to the OS.    Memory pressure handling has not changed much since SQL 2005 and it was described in detail in a blog post by Slava Oks.   Note that SQL Server Express is an exception to the above behavior. Unlike other editions it does not assume it is the most important process running on the system but tries to be more “desktop” friendly. It will empty its working set after a period of inactivity.   How does SQL Server respond to changing OS memory?    In SQL Server 2005 support for Hot-Add memory was introduced. This feature, available in Enterprise and above editions, allows the server to make use of any extra physical memory that was added after SQL Server started. Being able to add physical memory when the system is running is limited to specialized hardware, but with the Hyper-V Dynamic Memory feature, when new memory is allocated to a guest virtual machine, it looks like hot-add physical memory to the guest. What this means is that thanks to the hot-add memory feature, SQL Server 2005 and higher can dynamically grow if more “physical” memory is granted to a guest VM by Hyper-V dynamic memory.   SQL Server checks OS memory every second and dynamically adjusts its “target” (based on available OS memory and max server memory) accordingly.   In “Denali” Standard Edition will also have sqlserver.exe support for hot-add memory when running virtualized (i.e. detecting and acting on Hyper-V Dynamic Memory allocations).   How does a SQL Server workload in a guest VM impact Hyper-V dynamic memory scheduling?   When a SQL workload causes the sqlserver.exe process to grow its working set, the Hyper-V memory scheduler will detect memory pressure in the guest VM and add memory to it. SQL Server will then detect the extra memory and grow according to workload demand. In our tests we have seen this feedback process cause a guest VM to grow quickly in response to SQL workload - we are still working on characterizing this ramp-up.    How does SQL Server respond when Hyper-V removes memory from a guest VM through ballooning?   If pressure from other VM's cause Hyper-V Dynamic Memory to take memory away from a VM through ballooning (allocating memory with a virtual device driver and returning it to the host OS), Windows Memory Manager will page out unlocked portions of memory and signal low resource notification events. When SQL Server detects these events it will shrink memory until the low memory notifications stop (see cache shrinking description above).    This raises another question. Can we make SQL Server release memory more readily and hence behave more "dynamically" without compromising performance? In certain circumstances where the application workload is predictable it may be possible to have a job which varies "max server memory" according to need, lowering it when the engine is inactive and raising it before a period of activity. This would have limited applicaability but it is something we're looking into.   What Memory Management changes are there in SQL Server “Denali”?   In SQL Server “Denali” (aka SQL11) the Memory Manager has been re-written to be more efficient. The main changes are summarized in this post. An important change with respect to Hyper-V Dynamic Memory support is that now the max server memory setting includes any size page allocations and managed CLR procedure allocations it now represents a closer approximation to total sqlserver.exe memory usage. This makes it easier to calculate a value for max server memory, which becomes important when configuring virtual machines to work well with Hyper-V Dynamic Memory Startup and Maximum RAM settings.   Another important change is no more AWE or hot-add support for 32-bit edition. This means if you're running a 32-bit edition of Denali you're limited to a 4GB address space and will not be able to take advantage of dynamically added OS memory that wasn't present when SQL Server started (though Hyper-V Dynamic Memory is still a supported configuration).   In part 3 we’ll develop some best practices for configuring and using SQL Server with Dynamic Memory. Originally posted at http://blogs.msdn.com/b/sqlosteam/

  Read the article

• Cleaner HTML Markup with ASP.NET 4 Web Forms - Client IDs (VS 2010 and .NET 4.0 Series)

  - by ScottGu

  This is the sixteenth in a series of blog posts I’m doing on the upcoming VS 2010 and .NET 4 release. Today’s post is the first of a few blog posts I’ll be doing that talk about some of the important changes we’ve made to make Web Forms in ASP.NET 4 generate clean, standards-compliant, CSS-friendly markup.  Today I’ll cover the work we are doing to provide better control over the “ID” attributes rendered by server controls to the client. [In addition to blogging, I am also now using Twitter for quick updates and to share links. Follow me at: twitter.com/scottgu] Clean, Standards-Based, CSS-Friendly Markup One of the common complaints developers have often had with ASP.NET Web Forms is that when using server controls they don’t have the ability to easily generate clean, CSS-friendly output and markup.  Some of the specific complaints with previous ASP.NET releases include: Auto-generated ID attributes within HTML make it hard to write JavaScript and style with CSS Use of tables instead of semantic markup for certain controls (in particular the asp:menu control) make styling ugly Some controls render inline style properties even if no style property on the control has been set ViewState can often be bigger than ideal ASP.NET 4 provides better support for building standards-compliant pages out of the box.  The built-in <asp:> server controls with ASP.NET 4 now generate cleaner markup and support CSS styling – and help address all of the above issues.  Markup Compatibility When Upgrading Existing ASP.NET Web Forms Applications A common question people often ask when hearing about the cleaner markup coming with ASP.NET 4 is “Great - but what about my existing applications?  Will these changes/improvements break things when I upgrade?” To help ensure that we don’t break assumptions around markup and styling with existing ASP.NET Web Forms applications, we’ve enabled a configuration flag – controlRenderingCompatbilityVersion – within web.config that let’s you decide if you want to use the new cleaner markup approach that is the default with new ASP.NET 4 applications, or for compatibility reasons render the same markup that previous versions of ASP.NET used:   When the controlRenderingCompatbilityVersion flag is set to “3.5” your application and server controls will by default render output using the same markup generation used with VS 2008 and .NET 3.5.  When the controlRenderingCompatbilityVersion flag is set to “4.0” your application and server controls will strictly adhere to the XHTML 1.1 specification, have cleaner client IDs, render with semantic correctness in mind, and have extraneous inline styles removed. This flag defaults to 4.0 for all new ASP.NET Web Forms applications built using ASP.NET 4. Any previous application that is upgraded using VS 2010 will have the controlRenderingCompatbilityVersion flag automatically set to 3.5 by the upgrade wizard to ensure backwards compatibility.  You can then optionally change it (either at the application level, or scope it within the web.config file to be on a per page or directory level) if you move your pages to use CSS and take advantage of the new markup rendering. Today’s Cleaner Markup Topic: Client IDs The ability to have clean, predictable, ID attributes on rendered HTML elements is something developers have long asked for with Web Forms (ID values like “ctl00_ContentPlaceholder1_ListView1_ctrl0_Label1” are not very popular).  Having control over the ID values rendered helps make it much easier to write client-side JavaScript against the output, makes it easier to style elements using CSS, and on large pages can help reduce the overall size of the markup generated. New ClientIDMode Property on Controls ASP.NET 4 supports a new ClientIDMode property on the Control base class.  The ClientIDMode property indicates how controls should generate client ID values when they render.  The ClientIDMode property supports four possible values: AutoID—Renders the output as in .NET 3.5 (auto-generated IDs which will still render prefixes like ctrl00 for compatibility) Predictable (Default)— Trims any “ctl00” ID string and if a list/container control concatenates child ids (example: id=”ParentControl_ChildControl”) Static—Hands over full ID naming control to the developer – whatever they set as the ID of the control is what is rendered (example: id=”JustMyId”) Inherit—Tells the control to defer to the naming behavior mode of the parent container control The ClientIDMode property can be set directly on individual controls (or within container controls – in which case the controls within them will by default inherit the setting): Or it can be specified at a page or usercontrol level (using the <%@ Page %> or <%@ Control %> directives) – in which case controls within the pages/usercontrols inherit the setting (and can optionally override it): Or it can be set within the web.config file of an application – in which case pages within the application inherit the setting (and can optionally override it): This gives you the flexibility to customize/override the naming behavior however you want. Example: Using the ClientIDMode property to control the IDs of Non-List Controls Let’s take a look at how we can use the new ClientIDMode property to control the rendering of “ID” elements within a page.  To help illustrate this we can create a simple page called “SingleControlExample.aspx” that is based on a master-page called “Site.Master”, and which has a single <asp:label> control with an ID of “Message” that is contained with an <asp:content> container control called “MainContent”: Within our code-behind we’ll then add some simple code like below to dynamically populate the Label’s Text property at runtime:   If we were running this application using ASP.NET 3.5 (or had our ASP.NET 4 application configured to run using 3.5 rendering or ClientIDMode=AutoID), then the generated markup sent down to the client would look like below: This ID is unique (which is good) – but rather ugly because of the “ct100” prefix (which is bad). Markup Rendering when using ASP.NET 4 and the ClientIDMode is set to “Predictable” With ASP.NET 4, server controls by default now render their ID’s using ClientIDMode=”Predictable”.  This helps ensure that ID values are still unique and don’t conflict on a page, but at the same time it makes the IDs less verbose and more predictable.  This means that the generated markup of our <asp:label> control above will by default now look like below with ASP.NET 4: Notice that the “ct100” prefix is gone. Because the “Message” control is embedded within a “MainContent” container control, by default it’s ID will be prefixed “MainContent_Message” to avoid potential collisions with other controls elsewhere within the page. Markup Rendering when using ASP.NET 4 and the ClientIDMode is set to “Static” Sometimes you don’t want your ID values to be nested hierarchically, though, and instead just want the ID rendered to be whatever value you set it as.  To enable this you can now use ClientIDMode=static, in which case the ID rendered will be exactly the same as what you set it on the server-side on your control.  This will cause the below markup to be rendered with ASP.NET 4: This option now gives you the ability to completely control the client ID values sent down by controls. Example: Using the ClientIDMode property to control the IDs of Data-Bound List Controls Data-bound list/grid controls have historically been the hardest to use/style when it comes to working with Web Form’s automatically generated IDs.  Let’s now take a look at a scenario where we’ll customize the ID’s rendered using a ListView control with ASP.NET 4. The code snippet below is an example of a ListView control that displays the contents of a data-bound collection — in this case, airports: We can then write code like below within our code-behind to dynamically databind a list of airports to the ListView above: At runtime this will then by default generate a <ul> list of airports like below.  Note that because the <ul> and <li> elements in the ListView’s template are not server controls, no IDs are rendered in our markup: Adding Client ID’s to Each Row Item Now, let’s say that we wanted to add client-ID’s to the output so that we can programmatically access each <li> via JavaScript.  We want these ID’s to be unique, predictable, and identifiable. A first approach would be to mark each <li> element within the template as being a server control (by giving it a runat=server attribute) and by giving each one an id of “airport”: By default ASP.NET 4 will now render clean IDs like below (no ctl001-like ids are rendered):   Using the ClientIDRowSuffix Property Our template above now generates unique ID’s for each <li> element – but if we are going to access them programmatically on the client using JavaScript we might want to instead have the ID’s contain the airport code within them to make them easier to reference.  The good news is that we can easily do this by taking advantage of the new ClientIDRowSuffix property on databound controls in ASP.NET 4 to better control the ID’s of our individual row elements. To do this, we’ll set the ClientIDRowSuffix property to “Code” on our ListView control.  This tells the ListView to use the databound “Code” property from our Airport class when generating the ID: And now instead of having row suffixes like “1”, “2”, and “3”, we’ll instead have the Airport.Code value embedded within the IDs (e.g: _CLE, _CAK, _PDX, etc): You can use this ClientIDRowSuffix approach with other databound controls like the GridView as well. It is useful anytime you want to program row elements on the client – and use clean/identified IDs to easily reference them from JavaScript code. Summary ASP.NET 4 enables you to generate much cleaner HTML markup from server controls and from within your Web Forms applications.  In today’s post I covered how you can now easily control the client ID values that are rendered by server controls.  In upcoming posts I’ll cover some of the other markup improvements that are also coming with the ASP.NET 4 release. Hope this helps, Scott

  Read the article

• Add Free Windows Live Apps to Your Website or Blog

  - by Matthew Guay

  Would you like to use Hotmail, Office Web Apps, Messenger, and more on your website domain?  Here’s how you can add Windows Live to your website for free. Microsoft offers a popular suite of online communications products including Hotmail and Messenger.  Although Hotmail hasn’t been as popular in recent years as Gmail, it is getting a refresh this summer that might make it an even better email solution.  Additionally, the new Office Web Apps offer great compatibility with Office documents. While Skydrive offers 25Gb of free online file storage for all users, so Windows Live can make a great communications solution for your domain. Note: To signup for Windows Live for your domain, you will need to be able to add info to your WordPress.com blog or change Domain settings manually. Getting Started Open the Windows Live Custom Domains page (Link below) to get started adding Windows Live to your domain.  Your free Windows Live account will let you create up to 500 accounts, so it’s great for teams and groups that want to have customized email addresses in addition to those who just want an email account for their website. Enter your domain or subdomain you want to add to Windows Live in the box, and then select whether you want to setup Hotmail with this or now.  We want to add email to our domain, so select Set up Windows Live Hotmail for my domain and click Continue. You’ll need to sign in with a Windows Live ID to create the account, or choose to create a new Windows Live account associated with your domain.   Sign in with your Windows Live ID…this can be a Hotmail, Live Messenger, XBOX Live, Zune ID, or Microsoft.com account. Or, enter your information to create a new Windows Live ID if you selected the second option. Now, review your settings and make sure everything looks correct.  Click the I Accept button to setup your account.   Your account is now fully setup, but you’ll need to add or edit DNS information on your site.  The steps are slightly different depending if your site is hosted on WordPress.com, on your own server, or hosting service. We’ll show you how to do it on either one. First, though, note the information below this box.  You’ll see settings for your Mail setup…   Security settings…   And Messenger integration.  Make note of the settings, especially the circled ones, as we’ll need them in the next step. Integrate Windows Live with Your WordPress Blog If the domain you added to Windows Live is for your WordPress blog, login to your WordPress dashboard in a separate browser window or tab.  Click the arrow beside Upgrades, and select Domains from the menu. Click the Edit DNS link beside the domain name you’re adding to Windows Live. In the text box on this page, enter the following, replacing Your_info with your code from the Mail Setup box in your Windows Live Dashboard.  Note that this is the blurred section in our screenshots.  It should be a numerical code like 1234567890.pamx1.hotmail.com. MX 10 Your_info.pamx1.hotmail.com. TXT v=spf1 include:hotmail.com ~all CNAME Your_info domains.live.com. Click Save DNS records, and your settings are saved to WordPress.  Note that this will only integrate email with your WordPress account; you cannot integrate Messenger with a domain hosted on WordPress.com. Finally, return to your Windows Live Settings page and click Refresh.  If your settings are correct, you’ll now be ready to use Windows Live on your WordPress.com domain. Integrate Windows Live with Your Own Server If your website is hosted on your own server or hosting account, you’ll need to take a few more steps to add Windows Live to your domain.  This is fairly easy, but the steps may be different depending on your hosting company or registrar.  With some hosts, you may have to contact support to have them add the MX records for you.  Our site’s host uses the popular cPanel for website administration, so here’s how we added the MX Entries through cPanel. Login to your website’s cPanel, and select MX Entry under the Mail section. In the text box on this page, enter the following, replacing Your_info with your code from the Mail Setup box in your Windows Live Dashboard.  Note that this is the blurred section in our screenshots.  It should be a numerical code like 1234567890.pamx1.hotmail.com. MX 10 Your_info.pamx1.hotmail.com. Now, go back to your cPanel home, and select Advanced DNS Zone Editor under Domains. Here, add a TXT record with the following info: Name: yoursite.com. TTL: 3600 TXT Data: v=spf1 include:hotmail.com ~all Click Add Record and your Mail integration data is all configured. To integrate Messenger with your own domain, you’ll have to add an SRV entry to your DNS settings.  cPanel doesn’t have an option for this, so we had to contact our site’s hosting company and they added the entry for us.  Copy all of the information in the Messenger box and send it to your domain support, and they should be able to add this for you.  Alternately, if you don’t want or need Messenger, then you can simply skip this step. Once all of your settings are in place, return to your Windows Live Settings page and click Refresh.  If your settings are correct, you’ll now be ready to use Windows Live on your WordPress.com domain. Create a New Email Account On Your Domain Welcome to your new Windows Live admin page!  Now you can add email accounts so you and anyone else you want can access Hotmail and the other Windows Live apps with your domain.  Click Add to add an account. Enter an account name, which will be the email address of the account, e.g. [email protected].  Then enter the user’s name and a password for the account.  By default this will be a temporary password, and the user will have to change it on first log-in, but if you’re setting up this account for yourself, you can uncheck the box and keep this as your standard password. Now, go to www.mail.live.com, and sign in with your new email address and password.  Remember, your email address is your username previously entered followed by @yourdomain.com. To finish setting up the email account, enter your password, secret question and answer, alternate email, and location information.  Click I accept to finish setting up your new email account. Enter the characters in the Captcha to confirm you’re a human, and click Continue. Your new Hotmail inbox will now load, and you’ll have a welcome email in your inbox.  This works the same as normal Hotmail, except this time, your email address is with your own domain. You can now access any of the Windows Live services from the top-level menu. Here’s an Excel Spreadsheet open in the new Office Web Apps via SkyDrive on our new Windows Live account. If you setup Messenger access previously, you can now sign in to Windows Live Messenger using your new @yourdomain.com account as well. Important Links Accessing your Windows Live accounts is easy.  Simply go to any Windows Live site, such as www.hotmail.com or www.skydrive.com, and sign in with your new Windows Live ID from your domain as normal.  You don’t need a special address to access your account; it works just like the standard public Hotmail accounts. To administer your Windows Live for your domain, go to https://domains.live.com/ and sign in with the Windows Live ID you used to create the account.  Here you can add more users, change settings, and view usage details for the Windows Live accounts on your domain. Conclusion Windows Live is easy to add to your domain, and lets you create up to 500 email address for it.  With the upcoming updates to Hotmail and Office Web Apps coming this summer, this can be a nice way to make your domain even more useful.  And with 500 email accounts, you can easily let your team take advantage of your unique address as well. If you’d rather use Google’s online applications with your domain, check out our article on how to add free Google apps to your website or blog. Link Signup for Windows Live for Your Domain Similar Articles Productive Geek Tips Tools to Help Post Content On Your WordPress BlogBackup Your Windows Live Writer SettingsInstall Windows Live Essentials In Windows 7Add Your Gmail To Windows Live MailMysticgeek Blog: A Look at Internet Explorer 8 Beta 1 on Windows XP TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips HippoRemote Pro 2.2 Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Backup Drivers With Driver Magician TubeSort: YouTube Playlist Organizer XPS file format & XPS Viewer Explained Microsoft Office Web Apps Guide Know if Someone Accessed Your Facebook Account Shop for Music with Windows Media Player 12

  Read the article

• Add Free Google Apps to Your Website or Blog

  - by Matthew Guay

  Would you like to have an email address from your own domain, but prefer Gmail’s interface and integration with Google Docs?  Here’s how you can add the free Google Apps Standard to your site and get the best of both worlds. Note: To signup for Google Apps and get it setup on your domain, you will need to be able to add info to your WordPress blog or change Domain settings manually. Getting Started Head to the Google Apps signup page (link below), and click the Get Started button on the right.  Note that we are signing up for the free Google Apps which allows a max of 50 users; if you need more than 50 email addresses for your domain, you can choose Premiere Edition instead for $50/year. Select that you are the Administrator of the domain, and enter the domain or subdomain you want to use with Google Apps.  Here we’re adding Google Apps to the techinch.com site, but we could instead add Apps to mail.techinch.com if needed…click Get Started. Enter your name, phone number, an existing email address, and other Administrator information.  The Apps signup page also includes some survey questions about your organization, but you only have to fill in the required fields. On the next page, enter a username and password for the administrator account.  Note that the user name will also be the administrative email address as [email protected]. Now you’re ready to authenticate your Google Apps account with your domain.  The steps are slightly different depending on whether your site is on WordPress.com or on your own hosting service or server, so we’ll show how to do it both ways.   Authenticate and Integrate Google Apps with WordPress.com To add Google Apps to a domain you have linked to your WordPress.com blog, select Change yourdomain.com CNAME record and click Continue. Copy the code under #2, which should be something like googleabcdefg123456.  Do not click the button at the bottom; wait until we’ve completed the next step.   Now, in a separate browser window or tab, open your WordPress Dashboard.  Click the arrow beside Upgrades, and select Domains from the menu. Click the Edit DNS link beside the domain name you’re adding to Google Apps. Scroll down to the Google Apps section, and paste your code from Google Apps into the verification code field.  Click Generate DNS records when you’re done. This will add the needed DNS settings to your records in the box above the Google Apps section.  Click Save DNS records. Now, go back to the Google Apps signup page, and click I’ve completed the steps above. Authenticate Google Apps on Your Own Server If your website is hosted on your own server or hosting account, you’ll need to take a few more steps to add Google Apps to your domain.  You can add a CNAME record to your domain host using the same information that you would use with a WordPress account, or you can upload an HTML file to your site’s main directory.  In this test we’re going to upload an HTML file to our site for verification. Copy the code under #1, which should be something like googleabcdefg123456.  Do not click the button at the bottom; wait until we’ve completed the next step first. Create a new HTML file and paste the code in it.  You can do this easily in Notepad: create a new document, paste the code, and then save as googlehostedservice.html.  Make sure to select the type as All Files or otherwise the file will have a .txt extension. Upload this file to your web server via FTP or a web dashboard for your site.  Make sure it is in the top level of your site’s directory structure, and try visiting it at yoursite.com/googlehostedservice.html. Now, go back to the Google Apps signup page, and click I’ve completed the steps above. Setup Your Email on Google Apps When this is done, your Google Apps account should be activated and ready to finish setting up.  Google Apps will offer to launch a guide to step you through the rest of the process; you can click Launch guide if you want, or click Skip this guide to continue on your own and go directly to the Apps dashboard.   If you choose to open the guide, you’ll be able to easily learn the ropes of Google Apps administration.  Once you’ve completed the tutorial, you’ll be taken to the Google Apps dashboard. Most of the Google Apps will be available for immediate use, but Email may take a bit more setup.  Click Activate email to get your Gmail-powered email running on your domain.    Add Google MX Records to Your Server You will need to add Google MX records to your domain registrar in order to have your mail routed to Google.  If your domain is hosted on WordPress.com, you’ve already made these changes so simply click I have completed these steps.  Otherwise, you’ll need to manually add these records before clicking that button.   Adding MX Entries is fairly easy, but the steps may depend on your hosting company or registrar.  With some hosts, you may have to contact support to have them add the MX records for you.  Our site’s host uses the popular cPanel for website administration, so here’s how we added the MX Entries through cPanel. Add MX Entries through cPanel Login to your site’s cPanel, and click the MX Entry link under Mail. Delete any existing MX Records for your domain or subdomain first to avoid any complications or interactions with Google Apps.  If you think you may want to revert to your old email service in the future, save a copy of the records so you can switch back if you need. Now, enter the MX Records that Google listed.  Here’s our account after we added all of the entries to our account. Finally, return to your Google Apps Dashboard and click the I have completed these steps button at the bottom of the page. Activating Service You’re now officially finished activating and setting up your Google Apps account.  Google will first have to check the MX records for your domain; this only took around an hour in our test, but Google warns it can take up to 48 hours in some cases. You may then see that Google is updating its servers with your account information.  Once again, this took much less time than Google’s estimate. When everything’s finished, you can click the link to access the inbox of your new Administrator email account in Google Apps. Welcome to Gmail … at your own domain!  All of the Google Apps work just the same in this version as they do in the public @gmail.com version, so you should feel right at home. You can return to the Google Apps dashboard from the Administrative email account by clicking the Manage this domain at the top right. In the Dashboard, you can easily add new users and email accounts, as well as change settings in your Google Apps account and add your site’s branding to your Apps. Your Google Apps will work just like their standard @gmail.com counterparts.  Here’s an example of an inbox customized with the techinch logo and a Gmail theme. Links to Remember Here are the common links to your Google Apps online.  Substitute your domain or subdomain for yourdomain.com. Dashboard https://www.google.com/a/cpanel/yourdomain.com Email https://mail.google.com/a/yourdomain.com Calendar https://www.google.com/calendar/hosted/yourdomain.com Docs https://docs.google.com/a/yourdomain.com Sites https://sites.google.com/a/yourdomain.com Conclusion Google Apps offers you great webapps and webmail for your domain, and let’s you take advantage of Google’s services while still maintaining the professional look of your own domain.  Setting up your account can be slightly complicated, but once it’s finished, it will run seamlessly and you’ll never have to worry about email or collaboration with your team again. Signup for the free Google Apps Standard Similar Articles Productive Geek Tips Mysticgeek Blog: Create Your Own Simple iGoogle GadgetAccess Your Favorite Google Services in Chrome the Easy WayRevo Uninstaller Pro [REVIEW]Mysticgeek Blog: A Look at Internet Explorer 8 Beta 1 on Windows XPFind Similar Websites in Google Chrome TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Snagit 10 Video preview of new Windows Live Essentials 21 Cursor Packs for XP, Vista & 7 Map the Stars with Stellarium Use ILovePDF To Split and Merge PDF Files TimeToMeet is a Simple Online Meeting Planning Tool Easily Create More Bookmark Toolbars in Firefox

  Read the article

• Intermittent wired network issues in 14.04

  - by Tommy Brunn

  Since yesterday, my wired network connection has been dropping for a couple of seconds every 30 seconds or so. To my knowledge, I had not made any changes to my network. Output of ifconfig -a: ? ~ ifconfig -a eth0 Link encap:Ethernet HWaddr 6c:f0:49:b9:b1:7f inet addr:192.168.0.16 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::6ef0:49ff:feb9:b17f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11597 errors:0 dropped:0 overruns:0 frame:0 TX packets:9783 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:10101682 (10.1 MB) TX bytes:1215142 (1.2 MB) Interrupt:48 Base address:0x8000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:96691 errors:0 dropped:0 overruns:0 frame:0 TX packets:96691 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:13594355 (13.5 MB) TX bytes:13594355 (13.5 MB) lspci |grep Ethernet: 04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 03) Pinging my router: ? ~ ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. 64 bytes from 192.168.0.1: icmp_seq=1 ttl=64 time=0.435 ms 64 bytes from 192.168.0.1: icmp_seq=2 ttl=64 time=0.571 ms ping: sendmsg: Network is unreachable ping: sendmsg: Network is unreachable ping: sendmsg: Network is unreachable ping: sendmsg: Network is unreachable ping: sendmsg: Network is unreachable 64 bytes from 192.168.0.1: icmp_seq=8 ttl=64 time=1.03 ms And the output of route: ? ~ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 1 0 0 eth0 Some messages from /var/logs/syslog: ? ~ tail -f /var/log/syslog Jun 6 10:37:34 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:37:34 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:37:37 lolbox dnsmasq[1138]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:37:37 lolbox dnsmasq[1362]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:37:39 lolbox dhclient: XMT: Solicit on eth0, interval 8660ms. Jun 6 10:37:39 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:37:39 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:37:47 lolbox dhclient: XMT: Solicit on eth0, interval 16820ms. Jun 6 10:37:47 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:37:47 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:04 lolbox dhclient: XMT: Solicit on eth0, interval 34410ms. Jun 6 10:38:04 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:04 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:16 lolbox NetworkManager[862]: <warn> (eth0): DHCPv6 request timed out. Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): canceled DHCP transaction, DHCP client pid 13045 Jun 6 10:38:16 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) scheduled... Jun 6 10:38:16 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) started... Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): device state change: activated -> failed (reason 'ip-config-unavailable') [100 120 5] Jun 6 10:38:16 lolbox NetworkManager[862]: <info> NetworkManager state is now DISCONNECTED Jun 6 10:38:16 lolbox NetworkManager[862]: <warn> Activation (eth0) failed for connection 'Wired connection 1' Jun 6 10:38:16 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) complete. Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): device state change: failed -> disconnected (reason 'none') [120 30 0] Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): deactivating device (reason 'none') [0] Jun 6 10:37:34 lolbox whoopsie[1133]: online Jun 6 10:38:16 lolbox whoopsie[1133]: offline Jun 6 10:38:16 lolbox dbus[485]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Jun 6 10:38:16 lolbox dbus[485]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): canceled DHCP transaction, DHCP client pid 13044 Jun 6 10:38:16 lolbox NetworkManager[862]: <warn> DNS: plugin dnsmasq update failed Jun 6 10:38:16 lolbox NetworkManager[862]: <info> Removing DNS information from /sbin/resolvconf Jun 6 10:38:16 lolbox avahi-daemon[619]: Withdrawing address record for fe80::6ef0:49ff:feb9:b17f on eth0. Jun 6 10:38:16 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:38:16 lolbox avahi-daemon[619]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 6 10:38:16 lolbox avahi-daemon[619]: Withdrawing address record for 192.168.0.16 on eth0. Jun 6 10:38:16 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv4 with address 192.168.0.16. Jun 6 10:38:16 lolbox avahi-daemon[619]: Interface eth0.IPv4 no longer relevant for mDNS. Jun 6 10:38:16 lolbox dnsmasq[1362]: setting upstream servers from DBus Jun 6 10:38:17 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:38:17 lolbox avahi-daemon[619]: New relevant interface eth0.IPv6 for mDNS. Jun 6 10:38:17 lolbox avahi-daemon[619]: Registering new address record for fe80::6ef0:49ff:feb9:b17f on eth0.*. Jun 6 10:38:18 lolbox dnsmasq[1138]: no servers found in /var/run/dnsmasq/resolv.conf, will retry Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Auto-activating connection 'Wired connection 1'. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) starting connection 'Wired connection 1' Jun 6 10:38:18 lolbox NetworkManager[862]: <info> (eth0): device state change: disconnected -> prepare (reason 'none') [30 40 0] Jun 6 10:38:18 lolbox NetworkManager[862]: <info> NetworkManager state is now CONNECTING Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) scheduled... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) started... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) scheduled... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) complete. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) starting... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> (eth0): device state change: prepare -> config (reason 'none') [40 50 0] Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) successful. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) scheduled. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) complete. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) started... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> (eth0): device state change: config -> ip-config (reason 'none') [50 70 0] Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Beginning DHCPv4 transaction (timeout in 45 seconds) Jun 6 10:38:18 lolbox NetworkManager[862]: <info> dhclient started with pid 13160 Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Beginning DHCPv6 transaction (timeout in 45 seconds) Jun 6 10:38:18 lolbox NetworkManager[862]: <info> dhclient started with pid 13161 Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) complete. Jun 6 10:38:18 lolbox avahi-daemon[619]: Withdrawing address record for fe80::6ef0:49ff:feb9:b17f on eth0. Jun 6 10:38:18 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:38:18 lolbox avahi-daemon[619]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 6 10:38:18 lolbox dhclient: Internet Systems Consortium DHCP Client 4.2.4 Jun 6 10:38:18 lolbox dhclient: Copyright 2004-2012 Internet Systems Consortium. Jun 6 10:38:18 lolbox dhclient: All rights reserved. Jun 6 10:38:18 lolbox dhclient: For info, please visit https://www.isc.org/software/dhcp/ Jun 6 10:38:18 lolbox dhclient: Jun 6 10:38:19 lolbox dhclient: Internet Systems Consortium DHCP Client 4.2.4 Jun 6 10:38:19 lolbox dhclient: Copyright 2004-2012 Internet Systems Consortium. Jun 6 10:38:19 lolbox dhclient: All rights reserved. Jun 6 10:38:19 lolbox dhclient: For info, please visit https://www.isc.org/software/dhcp/ Jun 6 10:38:19 lolbox dhclient: Jun 6 10:38:19 lolbox NetworkManager[862]: <info> (eth0): DHCPv4 state changed nbi -> preinit Jun 6 10:38:19 lolbox dhclient: Bound to *:546 Jun 6 10:38:19 lolbox dhclient: Listening on Socket/eth0 Jun 6 10:38:19 lolbox dhclient: Sending on Socket/eth0 Jun 6 10:38:19 lolbox NetworkManager[862]: <info> (eth0): DHCPv6 state changed nbi -> preinit6 Jun 6 10:38:19 lolbox dhclient: Listening on LPF/eth0/6c:f0:49:b9:b1:7f Jun 6 10:38:19 lolbox dhclient: Sending on LPF/eth0/6c:f0:49:b9:b1:7f Jun 6 10:38:19 lolbox dhclient: Sending on Socket/fallback Jun 6 10:38:19 lolbox dhclient: DHCPREQUEST of 192.168.0.16 on eth0 to 255.255.255.255 port 67 (xid=0x3fc9376d) Jun 6 10:38:19 lolbox dhclient: XMT: Solicit on eth0, interval 1020ms. Jun 6 10:38:19 lolbox dhclient: send_packet6: Cannot assign requested address Jun 6 10:38:19 lolbox dhclient: dhc6: send_packet6() sent -1 of 77 bytes Jun 6 10:38:20 lolbox dhclient: DHCPACK of 192.168.0.16 from 192.168.0.1 Jun 6 10:38:20 lolbox dhclient: bound to 192.168.0.16 -- renewal in 41481 seconds. Jun 6 10:38:20 lolbox NetworkManager[862]: <info> (eth0): DHCPv4 state changed preinit -> reboot Jun 6 10:38:20 lolbox NetworkManager[862]: <info> address 192.168.0.16 Jun 6 10:38:20 lolbox NetworkManager[862]: <info> prefix 24 (255.255.255.0) Jun 6 10:38:20 lolbox NetworkManager[862]: <info> gateway 192.168.0.1 Jun 6 10:38:20 lolbox NetworkManager[862]: <info> nameserver '83.255.245.11' Jun 6 10:38:20 lolbox NetworkManager[862]: <info> nameserver '193.150.193.150' Jun 6 10:38:20 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Configure Commit) scheduled... Jun 6 10:38:20 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) started... Jun 6 10:38:20 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.0.16. Jun 6 10:38:20 lolbox avahi-daemon[619]: New relevant interface eth0.IPv4 for mDNS. Jun 6 10:38:20 lolbox avahi-daemon[619]: Registering new address record for 192.168.0.16 on eth0.IPv4. Jun 6 10:38:20 lolbox dhclient: XMT: Solicit on eth0, interval 2110ms. Jun 6 10:38:20 lolbox dhclient: send_packet6: Cannot assign requested address Jun 6 10:38:20 lolbox dhclient: dhc6: send_packet6() sent -1 of 77 bytes Jun 6 10:38:20 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:38:20 lolbox avahi-daemon[619]: New relevant interface eth0.IPv6 for mDNS. Jun 6 10:38:20 lolbox avahi-daemon[619]: Registering new address record for fe80::6ef0:49ff:feb9:b17f on eth0.*. Jun 6 10:38:21 lolbox NetworkManager[862]: <info> (eth0): device state change: ip-config -> secondaries (reason 'none') [70 90 0] Jun 6 10:38:21 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) complete. Jun 6 10:38:21 lolbox NetworkManager[862]: <info> (eth0): device state change: secondaries -> activated (reason 'none') [90 100 0] Jun 6 10:38:21 lolbox NetworkManager[862]: <info> NetworkManager state is now CONNECTED_GLOBAL Jun 6 10:38:21 lolbox NetworkManager[862]: <info> Policy set 'Wired connection 1' (eth0) as default for IPv4 routing and DNS. Jun 6 10:38:21 lolbox NetworkManager[862]: <info> Writing DNS information to /sbin/resolvconf Jun 6 10:38:21 lolbox dnsmasq[1362]: setting upstream servers from DBus Jun 6 10:38:21 lolbox dnsmasq[1362]: using nameserver 127.0.0.1#53 Jun 6 10:38:21 lolbox dnsmasq[1362]: using nameserver 193.150.193.150#53 Jun 6 10:38:21 lolbox dnsmasq[1362]: using nameserver 83.255.245.11#53 Jun 6 10:38:21 lolbox NetworkManager[862]: <info> Activation (eth0) successful, device activated. Jun 6 10:38:21 lolbox whoopsie[1133]: message repeated 2 times: [ offline] Jun 6 10:38:21 lolbox whoopsie[1133]: online Jun 6 10:38:21 lolbox ntpdate[13217]: Can't find host ntp.ubuntu.com: Name or service not known (-2) Jun 6 10:38:21 lolbox ntpdate[13217]: no servers can be used, exiting Jun 6 10:38:22 lolbox dnsmasq[1138]: reading /var/run/dnsmasq/resolv.conf Jun 6 10:38:22 lolbox dnsmasq[1138]: using nameserver 127.0.1.1#53 Jun 6 10:38:22 lolbox dhclient: XMT: Solicit on eth0, interval 4080ms. Jun 6 10:38:22 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:22 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:26 lolbox dhclient: XMT: Solicit on eth0, interval 8450ms. Jun 6 10:38:26 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:26 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:35 lolbox dhclient: XMT: Solicit on eth0, interval 16630ms. Jun 6 10:38:35 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:35 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:51 lolbox dhclient: XMT: Solicit on eth0, interval 34860ms. Jun 6 10:38:51 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:51 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:58 lolbox dnsmasq[1138]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:38:58 lolbox dnsmasq[1362]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:39:04 lolbox NetworkManager[862]: <warn> (eth0): DHCPv6 request timed out. Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): canceled DHCP transaction, DHCP client pid 13161 Jun 6 10:39:04 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) scheduled... Jun 6 10:39:04 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) started... Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): device state change: activated -> failed (reason 'ip-config-unavailable') [100 120 5] Jun 6 10:39:04 lolbox NetworkManager[862]: <info> NetworkManager state is now DISCONNECTED Jun 6 10:39:04 lolbox NetworkManager[862]: <warn> Activation (eth0) failed for connection 'Wired connection 1' Jun 6 10:38:22 lolbox whoopsie[1133]: online Jun 6 10:39:04 lolbox whoopsie[1133]: offline Jun 6 10:39:04 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) complete. Jun 6 10:39:04 lolbox dbus[485]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): device state change: failed -> disconnected (reason 'none') [120 30 0] Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): deactivating device (reason 'none') [0] Jun 6 10:39:04 lolbox dbus[485]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): canceled DHCP transaction, DHCP client pid 13160 Jun 6 10:39:04 lolbox avahi-daemon[619]: Withdrawing address record for fe80::6ef0:49ff:feb9:b17f on eth0. Jun 6 10:39:04 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:39:04 lolbox avahi-daemon[619]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 6 10:39:04 lolbox avahi-daemon[619]: Withdrawing address record for 192.168.0.16 on eth0. Jun 6 10:39:04 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv4 with address 192.168.0.16. Jun 6 10:39:04 lolbox avahi-daemon[619]: Interface eth0.IPv4 no longer relevant for mDNS. Jun 6 10:39:04 lolbox NetworkManager[862]: <warn> DNS: plugin dnsmasq update failed Jun 6 10:39:04 lolbox NetworkManager[862]: <info> Removing DNS information from /sbin/resolvconf Jun 6 10:39:04 lolbox dnsmasq[1362]: setting upstream servers from DBus Jun 6 10:39:05 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:39:05 lolbox avahi-daemon[619]: New relevant interface eth0.IPv6 for mDNS. Jun 6 10:39:05 lolbox avahi-daemon[619]: Registering new address record for fe80::6ef0:49ff:feb9:b17f on eth0.*. Jun 6 10:39:06 lolbox dnsmasq[1138]: no servers found in /var/run/dnsmasq/resolv.conf, will retry Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Auto-activating connection 'Wired connection 1'. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) starting connection 'Wired connection 1' Jun 6 10:39:07 lolbox NetworkManager[862]: <info> (eth0): device state change: disconnected -> prepare (reason 'none') [30 40 0] Jun 6 10:39:07 lolbox NetworkManager[862]: <info> NetworkManager state is now CONNECTING Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) scheduled... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) started... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) scheduled... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) complete. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) starting... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> (eth0): device state change: prepare -> config (reason 'none') [40 50 0] Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) successful. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) scheduled. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) complete. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) started... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> (eth0): device state change: config -> ip-config (reason 'none') [50 70 0] Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Beginning DHCPv4 transaction (timeout in 45 seconds) Jun 6 10:39:07 lolbox NetworkManager[862]: <info> dhclient started with pid 13270 Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Beginning DHCPv6 transaction (timeout in 45 seconds) Jun 6 10:39:07 lolbox NetworkManager[862]: <info> dhclient started with pid 13271 Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) complete. Jun 6 10:39:07 lolbox avahi-daemon[619]: Withdrawing address record for fe80::6ef0:49ff:feb9:b17f on eth0. Jun 6 10:39:07 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:39:07 lolbox avahi-daemon[619]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 6 10:39:07 lolbox dhclient: Internet Systems Consortium DHCP Client 4.2.4 Jun 6 10:39:07 lolbox dhclient: Copyright 2004-2012 Internet Systems Consortium. Jun 6 10:39:07 lolbox dhclient: All rights reserved. Jun 6 10:39:07 lolbox dhclient: For info, please visit https://www.isc.org/software/dhcp/ Jun 6 10:39:07 lolbox dhclient: Jun 6 10:39:08 lolbox dhclient: Internet Systems Consortium DHCP Client 4.2.4 Jun 6 10:39:08 lolbox dhclient: Copyright 2004-2012 Internet Systems Consortium. Jun 6 10:39:08 lolbox dhclient: All rights reserved. Jun 6 10:39:08 lolbox dhclient: For info, please visit https://www.isc.org/software/dhcp/ Jun 6 10:39:08 lolbox dhclient: Jun 6 10:39:08 lolbox dhclient: Bound to *:546 Jun 6 10:39:08 lolbox dhclient: Listening on Socket/eth0 Jun 6 10:39:08 lolbox dhclient: Sending on Socket/eth0 Jun 6 10:39:08 lolbox kernel: [ 1446.098590] type=1400 audit(1402043948.002:75): apparmor="DENIED" operation="signal" profile="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=13273 comm="nm-dhcp-client." requested_mask="send" denied_mask="send" signal=term peer="/sbin/dhclient" Jun 6 10:39:08 lolbox kernel: [ 1446.098599] type=1400 audit(1402043948.002:76): apparmor="DENIED" operation="signal" profile="/sbin/dhclient" pid=13273 comm="nm-dhcp-client." requested_mask="receive" denied_mask="receive" signal=term peer="/usr/lib/NetworkManager/nm-dhcp-client.action" Jun 6 10:39:08 lolbox NetworkManager[862]: <info> (eth0): DHCPv4 state changed nbi -> preinit Jun 6 10:39:08 lolbox dhclient: Listening on LPF/eth0/6c:f0:49:b9:b1:7f Jun 6 10:39:08 lolbox dhclient: Sending on LPF/eth0/6c:f0:49:b9:b1:7f Jun 6 10:39:08 lolbox dhclient: Sending on Socket/fallback Jun 6 10:39:08 lolbox dhclient: DHCPREQUEST of 192.168.0.16 on eth0 to 255.255.255.255 port 67 (xid=0x3e0183b9) Jun 6 10:39:08 lolbox dhclient: XMT: Solicit on eth0, interval 1050ms. Jun 6 10:39:08 lolbox dhclient: send_packet6: Cannot assign requested address Jun 6 10:39:08 lolbox dhclient: dhc6: send_packet6() sent -1 of 77 bytes Jun 6 10:39:09 lolbox dhclient: DHCPACK of 192.168.0.16 from 192.168.0.1 Jun 6 10:39:09 lolbox dhclient: bound to 192.168.0.16 -- renewal in 35498 seconds. Jun 6 10:39:09 lolbox NetworkManager[862]: <info> (eth0): DHCPv4 state changed preinit -> reboot Jun 6 10:39:09 lolbox NetworkManager[862]: <info> address 192.168.0.16 Jun 6 10:39:09 lolbox NetworkManager[862]: <info> prefix 24 (255.255.255.0) Jun 6 10:39:09 lolbox NetworkManager[862]: <info> gateway 192.168.0.1 Jun 6 10:39:09 lolbox NetworkManager[862]: <info> nameserver '83.255.245.11' Jun 6 10:39:09 lolbox NetworkManager[862]: <info> nameserver '193.150.193.150' Jun 6 10:39:09 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Configure Commit) scheduled... Jun 6 10:39:09 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) started... Jun 6 10:39:09 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.0.16. Jun 6 10:39:09 lolbox avahi-daemon[619]: New relevant interface eth0.IPv4 for mDNS. Jun 6 10:39:09 lolbox avahi-daemon[619]: Registering new address record for 192.168.0.16 on eth0.IPv4. Jun 6 10:39:09 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:39:09 lolbox avahi-daemon[619]: New relevant interface eth0.IPv6 for mDNS. Jun 6 10:39:09 lolbox avahi-daemon[619]: Registering new address record for fe80::6ef0:49ff:feb9:b17f on eth0.*. Jun 6 10:39:10 lolbox dhclient: XMT: Solicit on eth0, interval 2180ms. Jun 6 10:39:10 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:39:10 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:39:10 lolbox NetworkManager[862]: <info> (eth0): device state change: ip-config -> secondaries (reason 'none') [70 90 0] Jun 6 10:39:10 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) complete. Jun 6 10:39:10 lolbox NetworkManager[862]: <info> (eth0): device state change: secondaries -> activated (reason 'none') [90 100 0] Jun 6 10:39:10 lolbox NetworkManager[862]: <info> NetworkManager state is now CONNECTED_GLOBAL Jun 6 10:39:10 lolbox NetworkManager[862]: <info> Policy set 'Wired connection 1' (eth0) as default for IPv4 routing and DNS. Jun 6 10:39:10 lolbox NetworkManager[862]: <info> Writing DNS information to /sbin/resolvconf Jun 6 10:39:10 lolbox dnsmasq[1362]: setting upstream servers from DBus Jun 6 10:39:10 lolbox dnsmasq[1362]: using nameserver 127.0.0.1#53 Jun 6 10:39:10 lolbox dnsmasq[1362]: using nameserver 193.150.193.150#53 Jun 6 10:39:10 lolbox dnsmasq[1362]: using nameserver 83.255.245.11#53 Jun 6 10:39:10 lolbox NetworkManager[862]: <info> Activation (eth0) successful, device activated. Jun 6 10:39:10 lolbox whoopsie[1133]: message repeated 2 times: [ offline] Jun 6 10:39:10 lolbox whoopsie[1133]: online Jun 6 10:39:10 lolbox ntpdate[13339]: Can't find host ntp.ubuntu.com: Name or service not known (-2) Jun 6 10:39:10 lolbox ntpdate[13339]: no servers can be used, exiting Jun 6 10:39:11 lolbox dnsmasq[1138]: reading /var/run/dnsmasq/resolv.conf Jun 6 10:39:11 lolbox dnsmasq[1138]: using nameserver 127.0.1.1#53 Jun 6 10:39:12 lolbox dhclient: XMT: Solicit on eth0, interval 4350ms. Jun 6 10:39:12 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:39:12 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:39:16 lolbox dhclient: XMT: Solicit on eth0, interval 8740ms. Jun 6 10:39:16 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:39:16 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:39:17 lolbox dnsmasq[1138]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:39:17 lolbox dnsmasq[1362]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:39:25 lolbox dhclient: XMT: Solicit on eth0, interval 17610ms. Jun 6 10:39:25 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:39:25 lolbox dhclient: IA_NA status code NoAddrsAvail.

  Read the article

• Communication Between Your PC and Azure VM via Windows Azure Connect

  - by Shaun

  With the new release of the Windows Azure platform there are a lot of new features available. In my previous post I introduced a little bit about one of them, the remote desktop access to azure virtual machine. Now I would like to talk about another cool stuff – Windows Azure Connect.   What’s Windows Azure Connect I would like to quote the definition of the Windows Azure Connect in MSDN With Windows Azure Connect, you can use a simple user interface to configure IP-sec protected connections between computers or virtual machines (VMs) in your organization’s network, and roles running in Windows Azure. IP-sec protects communications over Internet Protocol (IP) networks through the use of cryptographic security services. There’s an image available at the MSDN as well that I would like to forward here As we can see, using the Windows Azure Connect the Worker Role 1 and Web Role 1 are connected with the development machines and database servers which some of them are inside the organization some are not. With the Windows Azure Connect, the roles deployed on the cloud could consume the resource which located inside our Intranet or anywhere in the world. That means the roles can connect to the local database, access the local shared resource such as share files, folders and printers, etc.   Difference between Windows Azure Connect and AppFabric It seems that the Windows Azure Connect are duplicated with the Windows Azure AppFabric. Both of them are aiming to solve the problem on how to communication between the resource in the cloud and inside the local network. The table below lists the differences in my understanding. Category Windows Azure Connect Windows Azure AppFabric Purpose An IP-sec connection between the local machines and azure roles. An application service running on the cloud. Connectivity IP-sec, Domain-joint Net Tcp, Http, Https Components Windows Azure Connect Driver Service Bus, Access Control, Caching Usage Azure roles connect to local database server Azure roles use local shared files,  folders and printers, etc. Azure roles join the local AD. Expose the local service to Internet. Move the authorization process to the cloud. Integrate with existing identities such as Live ID, Google ID, etc. with existing local services. Utilize the distributed cache.   And also some scenarios on which of them should be used. Scenario Connect AppFabric I have a service deployed in the Intranet and I want the people can use it from the Internet.   Y I have a website deployed on Azure and need to use a database which deployed inside the company. And I don’t want to expose the database to the Internet. Y   I have a service deployed in the Intranet and is using AD authorization. I have a website deployed on Azure which needs to use this service. Y   I have a service deployed in the Intranet and some people on the Internet can use it but need to be authorized and authenticated.   Y I have a service in Intranet, and a website deployed on Azure. This service can be used from Internet and that website should be able to use it as well by AD authorization for more functionalities. Y Y   How to Enable Windows Azure Connect OK we talked a lot information about the Windows Azure Connect and differences with the Windows Azure AppFabric. Now let’s see how to enable and use the Windows Azure Connect. First of all, since this feature is in CTP stage we should apply before use it. On the Windows Azure Portal we can see our CTP features status under Home, Beta Program page. You can send the apply to join the Beta Programs to Microsoft in this page. After a few days the Microsoft will send an email to you (the email of your Live ID) when it’s available. In my case we can see that the Windows Azure Connect had been activated by Microsoft and then we can click the Connect button on top, or we can click the Virtual Network item from the left navigation bar.   The first thing we need, if it’s our first time to enter the Connect page, is to enable the Windows Azure Connect. After that we can see our Windows Azure Connect information in this page.   Add a Local Machine to Azure Connect As we explained below the Windows Azure Connect can make an IP-sec connection between the local machines and azure role instances. So that we firstly add a local machine into our Azure Connect. To do this we will click the Install Local Endpoint button on top and then the portal will give us an URL. Copy this URL to the machine we want to add and it will download the software to us. This software will be installed in the local machines which we want to join the Connect. After installed there will be a tray-icon appeared to indicate this machine had been joint our Connect. The local application will be refreshed to the Windows Azure Platform every 5 minutes but we can click the Refresh button to let it retrieve the latest status at once. Currently my local machine is ready for connect and we can see my machine in the Windows Azure Portal if we switched back to the portal and selected back Activated Endpoints node.   Add a Windows Azure Role to Azure Connect Let’s create a very simple azure project with a basic ASP.NET web role inside. To make it available on Windows Azure Connect we will open the azure project property of this role from the solution explorer in the Visual Studio, and select the Virtual Network tab, check the Activate Windows Azure Connect. The next step is to get the activation token from the Windows Azure Portal. In the same page there is a button named Get Activation Token. Click this button then the portal will display the token to me. We copied this token and pasted to the box in the Visual Studio tab. Then we deployed this application to azure. After completed the deployment we can see the role instance was listed in the Windows Azure Portal - Virtual Connect section.   Establish the Connect Group The final task is to create a connect group which contains the machines and role instances need to be connected each other. This can be done in the portal very easy. The machines and instances will NOT be connected until we created the group for them. The machines and instances can be used in one or more groups. In the Virtual Connect section click the Groups and Roles node from the left side navigation bar and clicked the Create Group button on top. This will bring up a dialog to us. What we need to do is to specify a group name, description; and then we need to select the local computers and azure role instances into this group. After the Azure Fabric updated the group setting we can see the groups and the endpoints in the page. And if we switch back to the local machine we can see that the tray-icon have been changed and the status turned connected. The Windows Azure Connect will update the group information every 5 minutes. If you find the status was still in Disconnected please right-click the tray-icon and select the Refresh menu to retrieve the latest group policy to make it connected.   Test the Azure Connect between the Local Machine and the Azure Role Instance Now our local machine and azure role instance had been connected. This means each of them can communication to others in IP level. For example we can open the SQL Server port so that our azure role can connect to it by using the machine name or the IP address. The Windows Azure Connect uses IPv6 to connect between the local machines and role instances. You can get the IP address from the Windows Azure Portal Virtual Network section when select an endpoint. I don’t want to take a full example for how to use the Connect but would like to have two very simple tests. The first one would be PING.   When a local machine and role instance are connected through the Windows Azure Connect we can PING any of them if we opened the ICMP protocol in the Filewall setting. To do this we need to run a command line before test. Open the command window on the local machine and the role instance, execute the command as following netsh advfirewall firewall add rule name="ICMPv6" dir=in action=allow enable=yes protocol=icmpv6 Thanks to Jason Chen, Patriek van Dorp, Anton Staykov and Steve Marx, they helped me to enable  the ICMPv6 setting. For the full discussion we made please visit here. You can use the Remote Desktop Access feature to logon the azure role instance. Please refer my previous blog post to get to know how to use the Remote Desktop Access in Windows Azure. Then we can PING the machine or the role instance by specifying its name. Below is the screen I PING my local machine from my azure instance. We can use the IPv6 address to PING each other as well. Like the image following I PING to my role instance from my local machine thought the IPv6 address.   Another example I would like to demonstrate here is folder sharing. I shared a folder in my local machine and then if we logged on the role instance we can see the folder content from the file explorer window.   Summary In this blog post I introduced about another new feature – Windows Azure Connect. With this feature our local resources and role instances (virtual machines) can be connected to each other. In this way we can make our azure application using our local stuff such as database servers, printers, etc. without expose them to Internet.   Hope this helps, Shaun All documents and related graphics, codes are provided "AS IS" without warranty of any kind. Copyright © Shaun Ziyan Xu. This work is licensed under the Creative Commons License.

  Read the article

• How to Use USER_DEFINED Activity in OWB Process Flow

  - by Jinggen He

  Process Flow is a very important component of Oracle Warehouse Builder. With Process Flow, we can create and control the ETL process by setting all kinds of activities in a well-constructed flow. In Oracle Warehouse Builder 11gR2, there are 28 kinds of activities, which fall into three categories: Control activities, OWB specific activities and Utility activities. For more information about Process Flow activities, please refer to OWB online doc. Most of those activities are pre-defined for some specific use. For example, the Mapping activity allows execution an OWB mapping in Process Flow and the FTP activity allows an interaction between the local host and a remote FTP server. Besides those activities for specific purposes, the User Defined activity enables you to incorporate into a Process Flow an activity that is not defined within Warehouse Builder. So the User Defined activity brings flexibility and extensibility to Process Flow. In this article, we will take an amazing tour of using the User Defined activity. Let's start. Enable execution of User Defined activity Let's start this section from creating a very simple Process Flow, which contains a Start activity, a User Defined activity and an End Success activity. Leave all parameters of activity USER_DEFINED unchanged except that we enter /tmp/test.sh into the Value column of the COMMAND parameter. Then let's create the shell script test.sh in /tmp directory. Here is the content of /tmp/test.sh (this article is demonstrating a scenario in Linux system, and /tmp/test.sh is a Bash shell script): echo Hello World! > /tmp/test.txt Note: don't forget to grant the execution privilege on /tmp/test.sh to OS Oracle user. For simplicity, we just use the following command. chmod +x /tmp/test.sh OK, it's so simple that we’ve almost done it. Now deploy the Process Flow and run it. For a newly installed OWB, we will come across an error saying "RPE-02248: For security reasons, activity operator Shell has been disabled by the DBA". See below. That's because, by default, the User Defined activity is DISABLED. Configuration about this can be found in <ORACLE_HOME>/owb/bin/admin/Runtime.properties: property.RuntimePlatform.0.NativeExecution.Shell.security_constraint=DISABLED The property can be set to three different values: NATIVE_JAVA, SCHEDULER and DISBALED. Where NATIVE_JAVA uses the Java 'Runtime.exec' interface, SCHEDULER uses a DBMS Scheduler external job submitted by the Control Center repository owner which is executed by the default operating system user configured by the DBA. DISABLED prevents execution via these operators. We enable the execution of User Defined activity by setting: property.RuntimePlatform.0.NativeExecution.Shell.security_constraint= NATIVE_JAVA Restart the Control Center service for the change of setting to take effect. cd <ORACLE_HOME>/owb/rtp/sql sqlplus OWBSYS/<password of OWBSYS> @stop_service.sql sqlplus OWBSYS/<password of OWBSYS> @start_service.sql And then run the Process Flow again. We will see that the Process Flow completes successfully. The execution of /tmp/test.sh successfully generated a file /tmp/test.txt, containing the line Hello World!. Pass parameters to User Defined Activity The Process Flow created in the above section has a drawback: the User Defined activity doesn't accept any information from OWB nor does it give any meaningful results back to OWB. That's to say, it lacks interaction. Maybe, sometimes such a Process Flow can fulfill the business requirement. But for most of the time, we need to get the User Defined activity executed according to some information prior to that step. In this section, we will see how to pass parameters to the User Defined activity and pass them into the to-be-executed shell script. First, let's see how to pass parameters to the script. The User Defined activity has an input parameter named PARAMETER_LIST. This is a list of parameters that will be passed to the command. Parameters are separated from one another by a token. The token is taken as the first character on the PARAMETER_LIST string, and the string must also end in that token. Warehouse Builder recommends the '?' character, but any character can be used. For example, to pass 'abc,' 'def,' and 'ghi' you can use the following equivalent: ?abc?def?ghi? or !abc!def!ghi! or |abc|def|ghi| If the token character or '\' needs to be included as part of the parameter, then it must be preceded with '\'. For example '\\'. If '\' is the token character, then '/' becomes the escape character. Let's configure the PARAMETER_LIST parameter as below: And modify the shell script /tmp/test.sh as below: echo $1 is saying hello to $2! > /tmp/test.txt Re-deploy the Process Flow and run it. We will see that the generated /tmp/test.txt contains the following line: Bob is saying hello to Alice! In the example above, the parameters passed into the shell script are static. This case is not so useful because: instead of passing parameters, we can directly write the value of the parameters in the shell script. To make the case more meaningful, we can pass two dynamic parameters, that are obtained from the previous activity, to the shell script. Prepare the Process Flow as below: The Mapping activity MAPPING_1 has two output parameters: FROM_USER, TO_USER. The User Defined activity has two input parameters: FROM_USER, TO_USER. All the four parameters are of String type. Additionally, the Process Flow has two string variables: VARIABLE_FOR_FROM_USER, VARIABLE_FOR_TO_USER. Through VARIABLE_FOR_FROM_USER, the input parameter FROM_USER of USER_DEFINED gets value from output parameter FROM_USER of MAPPING_1. We achieve this by binding both parameters to VARIABLE_FOR_FROM_USER. See the two figures below. In the same way, through VARIABLE_FOR_TO_USER, the input parameter TO_USER of USER_DEFINED gets value from output parameter TO_USER of MAPPING_1. Also, we need to change the PARAMETER_LIST of the User Defined activity like below: Now, the shell script is getting input from the Mapping activity dynamically. Deploy the Process Flow and all of its necessary dependees then run the Process Flow. We see that the generated /tmp/test.txt contains the following line: USER B is saying hello to USER A! 'USER B' and 'USER A' are two outputs of the Mapping execution. Write the shell script within Oracle Warehouse Builder In the previous section, the shell script is located in the /tmp directory. But sometimes, when the shell script is small, or for the sake of maintaining consistency, you may want to keep the shell script inside Oracle Warehouse Builder. We can achieve this by configuring these three parameters of a User Defined activity properly: COMMAND: Set the path of interpreter, by which the shell script will be interpreted. PARAMETER_LIST: Set it blank. SCRIPT: Enter the shell script content. Note that in Linux the shell script content is passed into the interpreter as standard input at runtime. About how to actually pass parameters to the shell script, we can utilize variable substitutions. As in the following figure, ${FROM_USER} will be replaced by the value of the FROM_USER input parameter of the User Defined activity. So will the ${TO_USER} symbol. Besides the custom substitution variables, OWB also provide some system pre-defined substitution variables. You can refer to the online document for that. Deploy the Process Flow and run it. We see that the generated /tmp/test.txt contains the following line: USER B is saying hello to USER A! Leverage the return value of User Defined activity All of the previous sections are connecting the User Defined activity to END_SUCCESS with an unconditional transition. But what should we do if we want different subsequent activities for different shell script execution results? 1.  The simplest way is to add three simple-conditioned out-going transitions for the User Defined activity just like the figure below. In the figure, to simplify the scenario, we connect the User Defined activity to three End activities. Basically, if the shell script ends successfully, the whole Process Flow will end at END_SUCCESS, otherwise, the whole Process Flow will end at END_ERROR (in our case, ending at END_WARNING seldom happens). In the real world, we can add more complex and meaningful subsequent business logic. 2.  Or we can utilize complex conditions to work with different results of the User Defined activity. Previously, in our script, we only have this line: echo ${FROM_USER} is saying hello to ${TO_USER}! > /tmp/test.txt We can add more logic in it and return different values accordingly. echo ${FROM_USER} is saying hello to ${TO_USER}! > /tmp/test.txt if CONDITION_1 ; then ...... exit 0 fi if CONDITION_2 ; then ...... exit 2 fi if CONDITION_3 ; then ...... exit 3 fi After that we can leverage the result by checking RESULT_CODE in condition expression of those out-going transitions. Let's suppose that we have the Process Flow as the following graph (SUB_PROCESS_n stands for more different further processes): We can set complex condition for the transition from USER_DEFINED to SUB_PROCESS_1 like this: Other transitions can be set in the same way. Note that, in our shell script, we return 0, 2 and 3, but not 1. As in Linux system, if the shell script comes across a system error like IO error, the return value will be 1. We can explicitly handle such a return value. Summary Let's summarize what has been discussed in this article: How to create a Process Flow with a User Defined activity in it How to pass parameters from the prior activity to the User Defined activity and finally into the shell script How to write the shell script within Oracle Warehouse Builder How to do variable substitutions How to let the User Defined activity return different values and in what way can we leverage

  Read the article

• Entity Framework v1 &hellip; Brief Synopsis and Tips &ndash; Part 2

  - by Rohit Gupta

  Using Entity Framework with ASMX Web sErvices and WCF Web Service: If you use ASMX WebService to expose Entity objects from Entity Framework... then the ASMX Webservice does not  include object graphs, one work around is to use Facade pattern or to use WCF Service. The other important aspect of using ASMX Web Services along with Entity Framework is that the ASMX Client is not aware of the existence of EF v1 since the client solely deals with C# objects (not EntityObjects or ObjectContext). Since the client is not aware of the ObjectContext hence the client cannot participate in change tracking since the client only receives the Current Values and not the Orginal values when the service sends the the Entity objects to the client. Thus there are 2 drawbacks to using EntityFramework with ASMX Web Service: 1. Object state is not maintained... so to overcome this limitation we need insert/update single entity at a time and retrieve the original values for the entity being updated on the server/service end before calling Save Changes. 2. ASMX does not maintain object graphs... i.e. Customer.Reservations or Customer.Reservations.Trip relationships are not maintained. Thus you need to send these relationships separately from service to client. WCF Web Service overcomes the object graph limitation of ASMX Web Service, but we need to insure that we are populating all the non-null scalar properties of all the objects in the object graph before calling Update. WCF Web service still cannot overcome the second limitation of tracking changes to entities at the client end. Also note that the "Customer" class in the Client is very different from the "Customer" class in the Entity Framework Model Entities. They are incompatible with each other hence we cannot cast one to the other. However the .NET Framework translates the client "Customer" Entity to the EFv1 Model "customer" Entity once the entity is serialzed back on the ASMX server end. If you need change tracking enabled on the client then we need to use WCF Data Services which is available with VS 2010. ====================================================================================================== In WCF when adding an object that has relationships, the framework assumes that every object in the object graph needs to be added to store. for e.g. in a Customer.Reservations.Trip object graph, when a Customer Entity is added to the store, the EFv1 assumes that it needs to a add a Reservations collection and also Trips for each Reservation. Thus if we need to use existing Trips for reservations then we need to insure that we null out the Trip object reference from Reservations and set the TripReference to the EntityKey of the desired Trip instead. ====================================================================================================== Understanding Relationships and Associations in EFv1 The Golden Rule of EF is that it does not load entities/relationships unless you ask it to explicitly do so. However there is 1 exception to this rule. This exception happens when you attach/detach entities from the ObjectContext. If you detach an Entity in a ObjectGraph from the ObjectContext, then the ObjectContext removes the ObjectStateEntry for this Entity and all the relationship Objects associated with this Entity. For e.g. in a Customer.Order.OrderDetails if the Customer Entity is detached from the ObjectContext then you cannot traverse to the Order and OrderDetails Entities (that still exist in the ObjectContext) from the Customer Entity(which does not exist in the Object Context) Conversely, if you JOIN a entity that is not in the ObjectContext with a Entity that is in the ObjContext then the First Entity will automatically be added to the ObjContext since relationships for the 2 Entities need to exist in the ObjContext. ========================================================= You cannot attach an EntityCollection to an entity through its navigation property for e.g. you cannot code myContact.Addresses = myAddressEntityCollection ========================================================== Cascade Deletes in EDM: The Designer does not support specifying cascase deletes for a Entity. To enable cascasde deletes on a Entity in EDM use the Association definition in CSDL for the Entity. for e.g. SalesOrderDetail (SOD) has a Foreign Key relationship with SalesOrderHeader (SalesOrderHeader 1 : SalesOrderDetail *) if you specify a cascade Delete on SalesOrderHeader Entity then calling deleteObject on SalesOrderHeader (SOH) Entity will send delete commands for SOH record and all the SOD records that reference the SOH record. ========================================================== As a good design practise, if you use Cascade Deletes insure that Cascade delete facet is used both in the EDM as well as in the database. Even though it is not absolutely mandatory to have Cascade deletes on both Database and EDM (since you can see that just the Cascade delete spec on the SOH Entity in EDM will insure that SOH record and all related SOD records will be deleted from the database ... even though you dont have cascade delete configured in the database in the SOD table) ============================================================== Maintaining relationships in Code When Setting a Navigation property of a Entity (for e.g. setting the Contact Navigation property of Address Entity) the following rules apply : If both objects are detached, no relationship object will be created. You are simply setting a property the CLR way. If both objects are attached, a relationship object will be created. If only one of the objects is attached, the other will become attached and a relationship object will be created. If that detached object is new, when it is attached to the context its EntityState will be Added. One important rule to remember regarding synchronizing the EntityReference.Value and EntityReference.EntityKey properties is that when attaching an Entity which has a EntityReference (e.g. Address Entity with ContactReference) the Value property will take precedence and if the Value and EntityKey are out of sync, the EntityKey will be updated to match the Value. ====================================================== If you call .Load() method on a detached Entity then the .Load() operation will throw an exception. There is one exception to this rule. If you load entities using MergeOption.NoTracking, you will be able to call .Load() on such entities since these Entities are accessible by the ObjectContext. So the bottomline is that we need Objectontext to be able to call .Load() method to do deffered loading on EntityReference or EntityCollection. Another rule to remember is that you cannot call .Load() on entities that have a EntityState.Added State since the ObjectContext uses the EntityKey of the Primary (Parent) Entity when loading the related (Child) Entity (and not the EntityKey of the child (even if the EntityKey of the child is present before calling .Load()) ====================================================== You can use ObjContext.Add() to add a entity to the ObjContext and set the EntityState of the new Entity to EntityState.Added. here no relationships are added/updated. You can also use EntityCollection.Add() method to add an entity to another entity's related EntityCollection for e.g. contact has a Addresses EntityCollection so to add a new address use contact.Addresses.Add(newAddress) to add a new address to the Addresses EntityCollection. Note that if the entity does not already exist in the ObjectContext then calling contact.Addresses.Add(myAddress) will cause a new Address Entity to be added to the ObjContext with EntityState.Added and it will also add a RelationshipEntry (a relationship object) with EntityState.Added which connects the Contact (contact) with the new address newAddress. Note that if the entity already exists in the Objectcontext (being part theOtherContact.Addresses Collection), then calling contact.Addresses.Add(existingAddress) will add 2 RelationshipEntry objects to the ObjectStateEntry Collection, one with EntityState.Deleted and the other with EntityState.Added. This implies that the existingAddress Entity is removed from the theOtherContact.Addresses Collection and Added to the contact.Addresses Collection..effectively reassigning the address entity from the theOtherContact to "contact". This is called moving an existing entity to a new object graph. ====================================================== You usually use ObjectContext.Attach() and EntityCollection.Attach() methods usually when you need to reconstruct the ObjectGraph after deserializing the objects as received from a ASMX Web Service Client. Attach is usually used to connect existing Entities in the ObjectContext. When EntityCollection.Attach() is called the EntityState of the RelationshipEntry (the relationship object) remains as EntityState.unchanged whereas when EntityCollection.Add() method is called the EntityState of the relationship object changes to EntityState.Added or EntityState.Deleted as the situation demands. ========================================================= LINQ To Entities Tips: Select Many does Inner Join by default.   for e.g. from c in Contact from a in c.Address select c ... this will do a Inner Join between the Contacts and Addresses Table and return only those Contacts that have a Address. ======================================================== Group Joins Do LEFT Join by default. e.g. from a in Address join c in Contact ON a.Contact.ContactID == c.ContactID Into g WHERE a.CountryRegion == "US" select g; This query will do a left join on the Contact table and return contacts that have a address in "US" region The following query : from c in Contact join a in Address.Where(a1 => a1.CountryRegion == "US") on c.ContactID  equals a.Contact.ContactID into addresses select new {c, addresses} will do a left join on the Address table and return All Contacts. In these Contacts only those will have its Address EntityCollection Populated which have a Address in the "US" region, the other contacts will have 0 Addresses in the Address collection (even if addresses for those contacts exist in the database but are in a different region) ======================================================== Linq to Entities does not support DefaultIfEmpty().... instead use .Include("Address") Query Builder method to do a Left JOIN or use Group Joins if you need more control like Filtering on the Address EntityCollection of Contact Entity =================================================================== Use CreateSourceQuery() on the EntityReference or EntityCollection if you need to add filters during deferred loading of Entities (Deferred loading in EFv1 happens when you call Load() method on the EntityReference or EntityCollection. for e.g. var cust=context.Contacts.OfType<Customer>().First(); var sq = cust.Reservations.CreateSourceQuery().Where(r => r.ReservationDate > new DateTime(2008,1,1)); cust.Reservations.Attach(sq); This populates only those reservations that are older than Jan 1 2008. This is the only way (in EFv1) to Attach a Range of Entities to a EntityCollection using the Attach() method ================================================================== If you need to get the Foreign Key value for a entity e.g. to get the ContactID value from a Address Entity use this :                                address.ContactReference.EntityKey.EntityKeyValues.Where(k=> k.Key == "ContactID")

  Read the article

• Following the Thread in OSB

  - by Antony Reynolds

  Threading in OSB The Scenario I recently led an OSB POC where we needed to get high throughput from an OSB pipeline that had the following logic: 1. Receive Request 2. Send Request to External System 3. If Response has a particular value   3.1 Modify Request   3.2 Resend Request to External System 4. Send Response back to Requestor All looks very straightforward and no nasty wrinkles along the way.  The flow was implemented in OSB as follows (see diagram for more details): Proxy Service to Receive Request and Send Response Request Pipeline   Copies Original Request for use in step 3 Route Node   Sends Request to External System exposed as a Business Service Response Pipeline   Checks Response to Check If Request Needs to Be Resubmitted Modify Request Callout to External System (same Business Service as Route Node) The Proxy and the Business Service were each assigned their own Work Manager, effectively giving each of them their own thread pool. The Surprise Imagine our surprise when, on stressing the system we saw it lock up, with large numbers of blocked threads.  The reason for the lock up is due to some subtleties in the OSB thread model which is the topic of this post.   Basic Thread Model OSB goes to great lengths to avoid holding on to threads.  Lets start by looking at how how OSB deals with a simple request/response routing to a business service in a route node. Most Business Services are implemented by OSB in two parts.  The first part uses the request thread to send the request to the target.  In the diagram this is represented by the thread T1.  After sending the request to the target (the Business Service in our diagram) the request thread is released back to whatever pool it came from.  A multiplexor (muxer) is used to wait for the response.  When the response is received the muxer hands off the response to a new thread that is used to execute the response pipeline, this is represented in the diagram by T2. OSB allows you to assign different Work Managers and hence different thread pools to each Proxy Service and Business Service.  In out example we have the “Proxy Service Work Manager” assigned to the Proxy Service and the “Business Service Work Manager” assigned to the Business Service.  Note that the Business Service Work Manager is only used to assign the thread to process the response, it is never used to process the request. This architecture means that while waiting for a response from a business service there are no threads in use, which makes for better scalability in terms of thread usage. First Wrinkle Note that if the Proxy and the Business Service both use the same Work Manager then there is potential for starvation.  For example: Request Pipeline makes a blocking callout, say to perform a database read. Business Service response tries to allocate a thread from thread pool but all threads are blocked in the database read. New requests arrive and contend with responses arriving for the available threads. Similar problems can occur if the response pipeline blocks for some reason, maybe a database update for example. Solution The solution to this is to make sure that the Proxy and Business Service use different Work Managers so that they do not contend with each other for threads. Do Nothing Route Thread Model So what happens if there is no route node?  In this case OSB just echoes the Request message as a Response message, but what happens to the threads?  OSB still uses a separate thread for the response, but in this case the Work Manager used is the Default Work Manager. So this is really a special case of the Basic Thread Model discussed above, except that the response pipeline will always execute on the Default Work Manager.   Proxy Chaining Thread Model So what happens when the route node is actually calling a Proxy Service rather than a Business Service, does the second Proxy Service use its own Thread or does it re-use the thread of the original Request Pipeline? Well as you can see from the diagram when a route node calls another proxy service then the original Work Manager is used for both request pipelines.  Similarly the response pipeline uses the Work Manager associated with the ultimate Business Service invoked via a Route Node.  This actually fits in with the earlier description I gave about Business Services and by extension Route Nodes they “… uses the request thread to send the request to the target”. Call Out Threading Model So what happens when you make a Service Callout to a Business Service from within a pipeline.  The documentation says that “The pipeline processor will block the thread until the response arrives asynchronously” when using a Service Callout.  What this means is that the target Business Service is called using the pipeline thread but the response is also handled by the pipeline thread.  This implies that the pipeline thread blocks waiting for a response.  It is the handling of this response that behaves in an unexpected way. When a Business Service is called via a Service Callout, the calling thread is suspended after sending the request, but unlike the Route Node case the thread is not released, it waits for the response.  The muxer uses the Business Service Work Manager to allocate a thread to process the response, but in this case processing the response means getting the response and notifying the blocked pipeline thread that the response is available.  The original pipeline thread can then continue to process the response. Second Wrinkle This leads to an unfortunate wrinkle.  If the Business Service is using the same Work Manager as the Pipeline then it is possible for starvation or a deadlock to occur.  The scenario is as follows: Pipeline makes a Callout and the thread is suspended but still allocated Multiple Pipeline instances using the same Work Manager are in this state (common for a system under load) Response comes back but all Work Manager threads are allocated to blocked pipelines. Response cannot be processed and so pipeline threads never unblock – deadlock! Solution The solution to this is to make sure that any Business Services used by a Callout in a pipeline use a different Work Manager to the pipeline itself. The Solution to My Problem Looking back at my original workflow we see that the same Business Service is called twice, once in a Routing Node and once in a Response Pipeline Callout.  This was what was causing my problem because the response pipeline was using the Business Service Work Manager, but the Service Callout wanted to use the same Work Manager to handle the responses and so eventually my Response Pipeline hogged all the available threads so no responses could be processed. The solution was to create a second Business Service pointing to the same location as the original Business Service, the only difference was to assign a different Work Manager to this Business Service.  This ensured that when the Service Callout completed there were always threads available to process the response because the response processing from the Service Callout had its own dedicated Work Manager. Summary Request Pipeline Executes on Proxy Work Manager (WM) Thread so limited by setting of that WM.  If no WM specified then uses WLS default WM. Route Node Request sent using Proxy WM Thread Proxy WM Thread is released before getting response Muxer is used to handle response Muxer hands off response to Business Service (BS) WM Response Pipeline Executes on Routed Business Service WM Thread so limited by setting of that WM.  If no WM specified then uses WLS default WM. No Route Node (Echo functionality) Proxy WM thread released New thread from the default WM used for response pipeline Service Callout Request sent using proxy pipeline thread Proxy thread is suspended (not released) until the response comes back Notification of response handled by BS WM thread so limited by setting of that WM.  If no WM specified then uses WLS default WM. Note this is a very short lived use of the thread After notification by callout BS WM thread that thread is released and execution continues on the original pipeline thread. Route/Callout to Proxy Service Request Pipeline of callee executes on requestor thread Response Pipeline of caller executes on response thread of requested proxy Throttling Request message may be queued if limit reached. Requesting thread is released (route node) or suspended (callout) So what this means is that you may get deadlocks caused by thread starvation if you use the same thread pool for the business service in a route node and the business service in a callout from the response pipeline because the callout will need a notification thread from the same thread pool as the response pipeline.  This was the problem we were having. You get a similar problem if you use the same work manager for the proxy request pipeline and a business service callout from that request pipeline. It also means you may want to have different work managers for the proxy and business service in the route node. Basically you need to think carefully about how threading impacts your proxy services. References Thanks to Jay Kasi, Gerald Nunn and Deb Ayers for helping to explain this to me.  Any errors are my own and not theirs.  Also thanks to my colleagues Milind Pandit and Prasad Bopardikar who travelled this road with me. OSB Thread Model Great Blog Post on Thread Usage in OSB

  Read the article

• CodePlex Daily Summary for Tuesday, September 18, 2012

  CodePlex Daily Summary for Tuesday, September 18, 2012Popular ReleasesfastJSON: v2.0.5: 2.0.5 - fixed number parsing for invariant format - added a test for German locale number testing (,. problems)????????API for .Net SDK: SDK for .Net ??? Release 4: 2012?9?17??? ?????，???????????????。 ?????Release 3??????，???????，???，??? ??????????????????SDK，????????。 ??，??????? That's all.VidCoder: 1.4.0 Beta: First Beta release! Catches up to HandBrake nightlies with SVN 4937. Added PGS (Blu-ray) subtitle support. Additional framerates available: 30, 50, 59.94, 60 Additional sample rates available: 8, 11.025, 12 and 16 kHz Additional higher bitrates available for audio. Same as Source Constant Framerate available. Added Apple TV 3 preset. Added new Bob deinterlacing option. Introduced process isolation for encodes. Now if HandBrake crashes, VidCoder will keep running and continue pro...DNN Metro7 style Skin package: Metro7 style Skin for DotNetNuke 06.02.01: Stabilization release fixed this issues: Links not worked on FF, Chrome and Safari Modified packaging with own manifest file for install and source package. Moved the user Image on the Login to the left side. Moved h2 font-size to 24px. Note : This release Comes w/o source package about we still work an a solution. Who Needs the Visual Studio source files please go to source and download it from there. Known 16 CSS issues that related to the skin.css. All others are DNN default o...Visual Studio Icon Patcher: Version 1.5.1: This fixes a bug in the 1.5 release where it would crash when no language packs were installed for VS2010.sheetengine - Isometric HTML5 JavaScript Display Engine: sheetengine v1.1.0: This release of sheetengine introduces major drawing optimizations. A background canvas is created with the full drawn scenery onto which only the changed parts are redrawn. For example a moving object will cause only its bounding box to be redrawn instead of the full scene. This background canvas is copied to the main canvas in each iteration. For this reason the size of the bounding box of every object needs to be defined and also the width and height of the background canvas. The example...VFPX: Desktop Alerts 1.0.2: This update for the Desktop Alerts contains changes to behavior for setting custom sounds for alerts. I have removed ALERTWAV.TXT from the project, and also removed DA_DEFAULTSOUND from the VFPALERT.H file. The AlertManager class and Alert class both have a "default" cSound of ADDBS(JUSTPATH(_VFP.ServerName))+"alert.wav" --- so, as long as you distribute a sound file with the file name "alert.wav" along with the EXE, that file will be used. You can set your own sound file globally by setti...MCEBuddy 2.x: MCEBuddy 2.2.15: Changelog for 2.2.15 (32bit and 64bit) 1. Added support for %originalfilepath% to get the source file full path. Used for custom commands only. 2. Added support for better parsing of Media Portal XML files to extract ShowName and Episode Name and download additional details from TVDB (like Season No, Episode No etc). 3. Added support for TVDB seriesID in metadata 4. Added support for eMail non blocking UI testCrashReporter.NET : Exception reporting library for C# and VB.NET: CrashReporter.NET 1.2: *Added html mail format which shows hierarchical exception report for better understanding.PDF Viewer Web part: PDF Viewer Web Part: PDF Viewer Web PartMicrosoft Ajax Minifier: Microsoft Ajax Minifier 4.67: Fix issue #18629 - incorrectly handling null characters in string literals and not throwing an error when outside string literals. update for Issue #18600 - forgot to make the ///#DEBUG= directive also set a known-global for the given debug namespace. removed the kill-switch for disregarding preprocessor define-comments (///#IF and the like) and created a separate CodeSettings.IgnorePreprocessorDefines property for those who really need to turn that off. Some people had been setting -kil...MPC-BE: Media Player Classic BE 1.0.1.0 build 1122: MPC-BE is a free and open source audio and video player for Windows. MPC-BE is based on the original "Media Player Classic" project (Gabest) and "Media Player Classic Home Cinema" project (Casimir666), contains additional features and bug fixes. Supported Operating Systems: Windows XP SP2, Vista, 7 32bit/64bit System Requirements: An SSE capable CPU The latest DirectX 9.0c runtime (June 2010). Install it regardless of the operating system, they all need it. Web installer: http://www.micro...Preactor Object Model: Visual Studio Template .NET 3.5: Visual Studio Template with all the necessary files to get started with POM. You will still need to Get the Preactor.ObjectModel and Preactor.ObjectModleExtensions libraries from Nuget though. You will also need to sign with assembly with a strong name key.Lakana - WPF Framework: Lakana V2: Lakana V2 contains : - Lakana WPF Forms (with sample project) - Lakana WPF Navigation (with sample project)myCollections: Version 2.3.0.0: New in this version : Added TheGamesDB.net API for games and nds Added Fast search options Added order by Artist/Album for music Fixed several provider Performance improvement New Splash Screen BugFixingMicrosoft SQL Server Product Samples: Database: OData QueryFeed workflow activity: The OData QueryFeed sample activity shows how to create a workflow activity that consumes an OData resource, and renders entity properties in a Microsoft Excel 2010 worksheet or Microsoft Word 2010 document. Using the sample QueryFeed activity, you can consume any OData resource. The sample activity uses LINQ to project OData metadata into activity designer expression items. By setting activity expressions, a fully qualified OData query string is constructed consisting of Resource, Filter, Or...F# 3.0 Sample Pack: FSharp 3.0 Sample Pack for Visual Studio 2012 RTM: F# 3.0 Sample Pack for Visual Studio 2012 RTMANPR MX: ANPR_MX Release 1: ANPR MX Release 1 Features: Correctly detects plate area for the average North American plate. (It won't work for the "European" plate size.) Provides potential values for the recognized plate. Allows images 800x600 and below (.jpg / .png). The example requires the VC 10 runtime & .NET 4 Framework to be already installed. The Source code project was made on Visual Studio 2010.Cocktail: Cocktail v1.0.1: PrerequisitesVisual Studio 2010 with SP1 (any edition but Express) Optional: Silverlight 4 or 5 Note: Install Silverlight 4 Tools and then the Silverlight 4 Toolkit. Likewise for Silverlight 5 Tools and the Silverlight 5 Toolkit DevForce Express 6.1.8.1 Included in the Cocktail download, DevForce Express requires registration) Important: Install DevForce after all other components. Download contentsDebug and release assemblies API documentation Source code License.txt Re...weber: weber v0.1: first release, creates a basic browser shell and allows user to navigate to web sites.New Projects.NET Code Editor & Compiler Component: .Net compiler component with integrated advanced text box, VisualStudio like highlightning, ability to intercept and show StandardOutput strings.NET Plugin Manager: Provides agnostic functionality for tiered plugin loading, unloading, and plugin collection management.Amazon Control Panel v2: Amazon Control Panel is a application that lets you control you Amazon Seller Central account using the Amazon MWS (Merchant Web Service) API.AutoSPSourceBuilder: AutoSPSourceBuilder: a utility for automatically building a SharePoint 2010 or 2013 install source including service packs, language packs & cumulative updates.CAOS: RBAC acess controllChat Forum: An Internet  forum,  or message  board,  is  an online discussion  site conversations  in  the  form  of  posted  messages.CRM 2011 - Many-To-Many Relationship Entity View: This Silverlight Web Resource for CRM 2011 will allow user to see N:N relationship entity data from single place.dardasim: dardasim gil and lior Tel Cabir DolphinsDBAManage: ???????ERP??，????！DimDate Generator: A SSIS project for generation a data dimansion table and data.DNL: eine grße .net bibliothek für entwicklerDouban FM for Metro: A music radio client for http://douban.fm running on Windows 8 / WinRTExtended WPF Control: Extended WPF Control for research and learning.FizzBuzzDaveC: Implements the classic FizzBuzz programmine exercise.HamStart: Nothing for now...Infopath XSN Modifier: A tool for editing the dataconnections of Infopath.KH Picture Resizer: Picture Resizer ermöglicht es Bilder per Drag and Dop zu verkleinern. Das Program wurde in C# geschrieben und nutzt Windows Forms.Korean String Extension for .NET: ?? ??? ??? ????? ???? string??? ??? ????? Extension library for "string" class that enhances "Hangul Jamo system" features Lucky Loot - Tattoo Shop Management Application: Lucky Loot - Tattoo Shop Management Application Por: Eric Gabriel Rodrigues Castoldi Objetivo: Trabalho de Conclusão de Curso de Sistemas de InformaçãoMagnOS - C# Cosmos Operating System: MagnOS is an Open Source operating system, made to learn how to make operating systems with Cosmos.Móa mày: Project m?iOData Samples: A collection of samples demonstrating solutions and functionality in WCF Data Services, ODataLib and EdmLib.Online Image Editor: Online Photo CanvasOptimuss Administración: La mejor aplicación de Gestión y Control EscolarOptimuss Obelix: La mejor aplicación de Gestión y Control EscolarPersonal Website: My personal websitePlanisoft: Proyecto de Planilla para clinica los fresnosPROYECTODT: ..................................................................................................................PtLibrary: PtLibrary stands for Peter Thönell's Delphi library. PtSettings and PtSettingsGUI make the management and use of settings extremely easy and powerful.RTS WebServer: A small lightweight, modern and fast webserver (template). with in the feature the newest technologies like SPDY and websocketsStandards: Standards is an Intranet application (using Windows authentication) designed to document and manage company standards. It is written in C#/MVC 4.Truttle OS: This is an OS I made with CosmosWfp System: zdgdsfgdsfgzpo: projekt na zaliczenie zpo???: ???

  Read the article

• CodePlex Daily Summary for Tuesday, October 15, 2013

  CodePlex Daily Summary for Tuesday, October 15, 2013Popular ReleasesFFXIV Crafting Simulator: Crafting Simulator 2.4.1: -Fixed the offset for the new patch (Auto Loading function)iBoxDB.EX - Fast Transactional NoSQL Database Resources: iBoxDB.net fast transactional nosql database 1.5.2: Easily process objects and documents, zero configuration. fast embeddable transactional nosql document database, includes CURD, QueryLanguage, Master-Master-Slave Replication, MVCC, etc. supports .net2, .net4, windows phone, mono, unity3d, node.js , copy and run. http://download-codeplex.sec.s-msft.com/Download?ProjectName=iboxdb&DownloadId=737783 Benchmark with MongoDB Compatibility more platforms for java versionneurogoody: slicebox: this is the slice box jsEvent-Based Components AppBuilder: AB3.AppDesigner.55: Iteration 55 (Feature): Moving of TargetEdge (simple wires only) by mouse.Sandcastle Help File Builder: SHFB v1.9.8.0 with Visual Studio Package: General InformationIMPORTANT: On some systems, the content of the ZIP file is blocked and the installer may fail to run. Before extracting it, right click on the ZIP file, select Properties, and click on the Unblock button if it is present in the lower right corner of the General tab in the properties dialog. This new release contains bug fixes and feature enhancements. There are some potential breaking changes in this release as some features of the Help File Builder have been moved into...SharpConfig: SharpConfig 1.2: Implemented comment parsing. Comments are now part of settings and setting categories. New properties: Setting: Comment PreComments SettingCategory: Comment PreCommentsC++ REST SDK (codename "Casablanca"): C++ REST SDK 1.3.0: This release fixes multiple customer reported issues as well as the following: Full support for Dev12 binaries and project files Full support for Windows XP New sample highlighting the Client and Server APIs : BlackJack Expose underlying native handle to set custom options on http_client Improvements to Listener Library Note: Dev10 binaries have been dropped as of this release, however the Dev10 project files are still available in the Source CodeAD ACL Scanner: 1.3.2: Minor bug fixed: Powershell 4.0 will report: Select—Object: Parameter cannot be processed because the parameter name p is ambiguous.Json.NET: Json.NET 5.0 Release 7: New feature - Added support for Immutable Collections New feature - Added WriteData and ReadData settings to DataExtensionAttribute New feature - Added reference and type name handling support to extension data New feature - Added default value and required support to constructor deserialization Change - Extension data is now written when serializing Fix - Added missing casts to JToken Fix - Fixed parsing large floating point numbers Fix - Fixed not parsing some ISO date ...RESX Manager: ResxManager 0.2.1: FIXED: Many critical bugs have been fixed. New Features Error logging for improved exception handling New toolbar Improvements of user interfaceFast YouTube Downloader: YouTube Downloader 2.2.0: YouTube Downloader 2.2.0VidCoder: 1.5.8 Beta: Added hardware acceleration options: Bicubic OpenCL scaling algorithm, QSV decoding/encoding and DXVA decoding. Updated HandBrake core to SVN 5834. Updated VidCoder setup icon. Fixed crash when choosing the mp4v2 container on x86 and opening on x64. Warning: the hardware acceleration features require specific hardware or file types to work correctly: QSV: Need an Intel processor that supports Quick Sync Video encoding, with a monitor hooked up to the Intel HD Graphics output and the lat...ASP.net MVC Awesome - jQuery Ajax Helpers: 3.5.2: version 3.5.2 - fix for setting single value to multivalue controls - datepicker min max date offset fix - html encoding for keys fix - enable Column.ClientFormatFunc to be a function call that will return a function version 3.5.1 - fixed html attributes rendering - fixed loading animation rendering - css improvements version 3.5 ========================== - autosize for all popups ( can be turned off by calling in js awe.autoSize = false ) - added Parent, Paremeter extensions ...Wsus Package Publisher: Release v1.3.1310.12: Allow the Update Creation Wizard to be set in full screen mode. Fix a bug which prevent WPP to Reset Remote Sus Client ID. Change the behavior of links in the Update Detail Viewer. Left-Click to open, Right-Click to copy to the Clipboard.TerrariViewer: TerrariViewer v7 [Terraria Inventory Editor]: This is a complete overhaul but has the same core style. I hope you enjoy it. This version is compatible with 1.2.0.3 Please send issues to my Twitter or https://github.com/TJChap2840WDTVHubGen - Adds Metadata, thumbnails and subtitles to WDTV Live Hubs: WDTVHubGen.v2.1.6.maint: I think this covers all of the issues. new additions: fixed the thumbnail problem for backgrounds. general clean up and error checking. need to get this put through the wringer and all feedback is welcome.BIDS Helper: BIDS Helper 1.6.4: This BIDS Helper release brings the following new features and fixes: New Features: A new Bus Matrix style report option when you run the Printer Friendly Dimension Usage report for an SSAS cube. The Biml engine is now fully in sync with the supported subset of Varigence Mist 3.4. This includes a large number of language enhancements, bugfixes, and project deployment support. Fixed Issues: Fixed Biml execution for project connections fixing a bug with Tabular Translations Editor not a...MoreTerra (Terraria World Viewer): MoreTerra 1.11.3: =========== =New Features= =========== New Markers added for Plantera's Bulb, Heart Fruits and Gold Cache. Markers now correctly display for the gems found in rock debris on the floor. =========== =Compatibility= =========== Fixed header changes found in Terraria 1.0.3.1Media Companion: Media Companion MC3.581b: Fix in place for TVDB xml issue. New* Movie - General Preferences, allow saving of ignored 'The' or 'A' to end of movie title, stored in sorttitle field. * Movie - New Way for Cropping Posters. Fixed* Movie - Rename of folders/filename. caught error message. * Movie - Fixed Bug in Save Cropped image, only saving in Pre-Frodo format if Both model selected. * Movie - Fixed Cropped image didn't take zoomed ratio into effect. * Movie - Separated Folder Renaming and File Renaming fuctions durin...SmartStore.NET - Free ASP.NET MVC Ecommerce Shopping Cart Solution: SmartStore.NET 1.2.0: HighlightsMulti-store support "Trusted Shops" plugins Highly improved SmartStore.biz Importer plugin Add custom HTML content to pages Performance optimization New FeaturesMulti-store-support: now multiple stores can be managed within a single application instance (e.g. for building different catalogs, brands, landing pages etc.) Added 3 new Trusted Shops plugins: Seal, Buyer Protection, Store Reviews Added Display as HTML Widget to CMS Topics (store owner now can add arbitrary HT...New ProjectsArtezio SharePoint 2013 Workflow Activities: SharePoint Workflow 2013 doesn’t provide activities to work with permissions, we've fixed it using HttpSend activity that makes REST API calls.Dependency.Injection: An attempt to write a really simple dependency injection framework. Does property-based and recursive dependency injection. Handles singletons. Yay!DHGMS SUO Killer: SUO Killer is a Visual Studio extension to deal with the removal of SUO file to mitigate SUO related issues in Visual Studio. This project is written in C#.dynamicsheet: dynamicsheetExcel Comparator: Excel Comparator is an add-in for Microsoft Excel that allows the user to compare a range between two sheets. FetchAIP: FetchAIP is a utility to download the various sections of the Aeronautical Information Publication (AIP) for New Zealand.Fluent Method and Type Builder: Still working on the summary.getboost: NuGet package for Boost framework.Goldstone Forum: WebForms Forum - TelerikAcademy Team ProjectGroupMe Software Development Kit: .NET Software Development Kit for http://groupme.com/ chat service.GSLMS: ----Import Excel Files Into SQL Server: Load Excel files into SQL Database without schema changes.Inaction: ?????????? jBegin: Learning ASP.net MVC from beginning, then here will be the source code for jbegin.comKDG's Statistical Quality Control Solver: This tool will include methods that can solve sample standard deviation, sample variance, median, mode, moving average, percentiles, margin of error, etc.kpi: Key Performance Indicator (KPI)????; visual studio 2010 with .NET 4.0 runtimeLECO Remote Control Client Application: Sample code and binaries are provided to demonstrate the remote control capability of a LECO Cornerstone instrument.LinkPad: My first Windows Store app intended for student to sketch up thoughts and concepts in quick diagrams.Modler.NET - Automating Graphical Data Model Co-Evolution: Modler.NET was the tool created for a Master's thesis project, which automates the co-evolution of graphical data models and the database that they represent.MyFileManager1: SummaryNever Lotto: Korean 465 Lotto Analyzer and Simulator. The real purpose of this project is to show that this kind of lotto things are just shit.NHibernate: The purpose of this project is to demo CRUD operations using NHibernate with Mono in Visual Studio 2012 using C# language. OAuth2 Authorizer: OAuth2 Authorizer helps you get the access code for a standard OAuth2 REST service that implements 3-legged authentication.Regular Expression for Excel: Regular Expression For Excel is an Excel Plugin. It provides a regular expressions EXCEL support. We can use it in the EXCEL function.Service Tester: Service Tester is an Azure Cloud based load testing application targeted at Soap Web Services which allows you to invoke your Web Service by random parameters.Simple TypeScript and C# Class Generator: Simple GUI application to generate compatible class source code for C# and TypeScript for communications between C# and TypeScript. Soccer team management: ---Spanner: No more stringly-typed web development! Build statically typed single page web applications in C#, automatically generating all HTML, JavaScript, and Knockout.

  Read the article

• OSX 10.6 Cisco IPSEC strange behavior

  - by tair

  I'm trying to connect to Cisco IPSEC VPN of my company over DSL Internet. I managed to successfully connect using Cisco VPN Client, now I'm trying to switch to OSX 10.6 native client, because of licensing issues. The problems is that the connection fails with a dialog box containing the message: The negotiation with the VPN server failed. Verify the server address and try reconnecting. I checked logs: Jun 29 13:10:39 racoon[4551]: Connecting. Jun 29 13:10:39 racoon[4551]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1). Jun 29 13:10:39 racoon[4551]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2). Jun 29 13:10:39 racoon[4551]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2). Jun 29 13:10:39 racoon[4551]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode). Jun 29 13:10:39 racoon[4551]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3). Jun 29 13:10:42 racoon[4551]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:10:42 racoon[4551]: IKEv1 XAUTH: success. (XAUTH Status is OK). Jun 29 13:10:42 racoon[4551]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:10:42 racoon[4551]: IKEv1 Config: retransmited. (Mode-Config retransmit). Jun 29 13:10:42 racoon[4551]: IKE Packet: receive success. (MODE-Config). Jun 29 13:10:42 configd[19]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.1.107), current interface setting (name: u92.168.54.147, subnet: 255.255.255.0, destination: 192.168.54.147). Jun 29 13:10:42 configd[19]: network configuration changed. Jun 29 13:10:42 vmnet-bridge[111]: Dynamic store changed Jun 29 13:10:42 named[62]: not listening on any interfaces Jun 29 13:10:58: --- last message repeated 1 time --- Jun 29 13:10:58 configd[19]: SCNCController: Disconnecting. (Connection tried to negotiate for, 16 seconds). Jun 29 13:10:58 racoon[4551]: IKE Packet: transmit success. (Information message). Jun 29 13:10:58 racoon[4551]: IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA). Jun 29 13:10:58 racoon[4551]: Disconnecting. (Connection tried to negotiate for, 19.113382 seconds). Jun 29 13:10:58 named[62]: not listening on any interfaces Jun 29 13:10:58 vmnet-bridge[111]: Dynamic store changed Jun 29 13:10:58 named[62]: not listening on any interfaces Jun 29 13:10:58 configd[19]: network configuration changed. Then I opened Terminal, started pinging a server behind VPN, and tried to connect again. Now connection is OK! Logs this time: Jun 29 13:46:53 racoon[8136]: Connecting. Jun 29 13:46:53 racoon[8136]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1). Jun 29 13:46:53 racoon[8136]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2). Jun 29 13:46:53 racoon[8136]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2). Jun 29 13:46:53 racoon[8136]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode). Jun 29 13:46:53 racoon[8136]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:46:56 racoon[8136]: IKEv1 XAUTH: success. (XAUTH Status is OK). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:46:56 racoon[8136]: IKEv1 Config: retransmited. (Mode-Config retransmit). Jun 29 13:46:56 racoon[8136]: IKE Packet: receive success. (MODE-Config). Jun 29 13:46:56 configd[19]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.1.107), current interface settinaddress: 192.168.54.149, subnet: 255.255.255.0, destination: 192.168.54.149). Jun 29 13:46:56 vmnet-bridge[111]: Dynamic store changed Jun 29 13:46:56 named[62]: not listening on any interfaces Jun 29 13:46:56 configd[19]: network configuration changed. Jun 29 13:46:56 named[62]: not listening on any interfaces Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1). Jun 29 13:46:56 racoon[8136]: IKE Packet: receive success. (Initiator, Quick-Mode message 2). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3). Jun 29 13:46:56 racoon[8136]: IKEv1 Phase2 Initiator: success. (Initiator, Quick-Mode). Jun 29 13:46:56 racoon[8136]: Connected. Jun 29 13:46:56 configd[19]: SCNCController: Connected. I tested it several times and it consistently behaves the same. What is the magic?

  Read the article

• OSX 10.6 Cisco IPSEC strange behavior

  - by tair

  I'm trying to connect to Cisco IPSEC VPN of my company over DSL Internet. I managed to successfully connect using Cisco VPN Client, now I'm trying to switch to OSX 10.6 native client, because of licensing issues. The problems is that the connection fails with a dialog box containing the message: The negotiation with the VPN server failed. Verify the server address and try reconnecting. I checked logs: Jun 29 13:10:39 racoon[4551]: Connecting. Jun 29 13:10:39 racoon[4551]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1). Jun 29 13:10:39 racoon[4551]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2). Jun 29 13:10:39 racoon[4551]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2). Jun 29 13:10:39 racoon[4551]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode). Jun 29 13:10:39 racoon[4551]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3). Jun 29 13:10:42 racoon[4551]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:10:42 racoon[4551]: IKEv1 XAUTH: success. (XAUTH Status is OK). Jun 29 13:10:42 racoon[4551]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:10:42 racoon[4551]: IKEv1 Config: retransmited. (Mode-Config retransmit). Jun 29 13:10:42 racoon[4551]: IKE Packet: receive success. (MODE-Config). Jun 29 13:10:42 configd[19]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.1.107), current interface setting (name: u92.168.54.147, subnet: 255.255.255.0, destination: 192.168.54.147). Jun 29 13:10:42 configd[19]: network configuration changed. Jun 29 13:10:42 vmnet-bridge[111]: Dynamic store changed Jun 29 13:10:42 named[62]: not listening on any interfaces Jun 29 13:10:58: --- last message repeated 1 time --- Jun 29 13:10:58 configd[19]: SCNCController: Disconnecting. (Connection tried to negotiate for, 16 seconds). Jun 29 13:10:58 racoon[4551]: IKE Packet: transmit success. (Information message). Jun 29 13:10:58 racoon[4551]: IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA). Jun 29 13:10:58 racoon[4551]: Disconnecting. (Connection tried to negotiate for, 19.113382 seconds). Jun 29 13:10:58 named[62]: not listening on any interfaces Jun 29 13:10:58 vmnet-bridge[111]: Dynamic store changed Jun 29 13:10:58 named[62]: not listening on any interfaces Jun 29 13:10:58 configd[19]: network configuration changed. Then I opened Terminal, started pinging a server behind VPN, and tried to connect again. Now connection is OK! Logs this time: Jun 29 13:46:53 racoon[8136]: Connecting. Jun 29 13:46:53 racoon[8136]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1). Jun 29 13:46:53 racoon[8136]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2). Jun 29 13:46:53 racoon[8136]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2). Jun 29 13:46:53 racoon[8136]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode). Jun 29 13:46:53 racoon[8136]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:46:56 racoon[8136]: IKEv1 XAUTH: success. (XAUTH Status is OK). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:46:56 racoon[8136]: IKEv1 Config: retransmited. (Mode-Config retransmit). Jun 29 13:46:56 racoon[8136]: IKE Packet: receive success. (MODE-Config). Jun 29 13:46:56 configd[19]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.1.107), current interface settinaddress: 192.168.54.149, subnet: 255.255.255.0, destination: 192.168.54.149). Jun 29 13:46:56 vmnet-bridge[111]: Dynamic store changed Jun 29 13:46:56 named[62]: not listening on any interfaces Jun 29 13:46:56 configd[19]: network configuration changed. Jun 29 13:46:56 named[62]: not listening on any interfaces Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1). Jun 29 13:46:56 racoon[8136]: IKE Packet: receive success. (Initiator, Quick-Mode message 2). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3). Jun 29 13:46:56 racoon[8136]: IKEv1 Phase2 Initiator: success. (Initiator, Quick-Mode). Jun 29 13:46:56 racoon[8136]: Connected. Jun 29 13:46:56 configd[19]: SCNCController: Connected. I tested it several times and it consistently behaves the same. What is the magic?

  Read the article

• Can't log in via SSH to any accounts set to use /bin/bash as a default shell

  - by Gui Ambros

  I'm trying to install bash as the default shell on a ARM Linux running on an embedded device (Synology DS212+ NAS). But there's something really wrong, and I can't figure out what it is. Symptoms: 1) Root has /bin/bash as default shell, and can log in normally via SSH: $ grep root /etc/passwd root:x:0:0:root:/root:/bin/bash $ ssh root@NAS root@NAS's password: Last login: Sun Dec 16 14:06:56 2012 from desktop # 2) joeuser has /bin/bash as default shell, and receives "Permission denied" when trying to log in via SSH: $ grep joeuser /etc/passwd joeuser:x:1029:100:Joe User:/home/joeuser:/bin/bash $ ssh joeuser@localhost joeuser@NAS's password: Last login: Sun Dec 16 14:07:22 2012 from desktop Permission denied, please try again. Connection to localhost closed. 3) changing joeuser's shell back to /bin/sh: $ grep joeuser /etc/passwd joeuser:x:1029:100:Joe User:/home/joeuser:/bin/sh $ ssh joeuser@localhost Last login: Sun Dec 16 15:50:52 2012 from localhost $ To make things even more strange, I can log in as joeuser using /bin/bash using the serial console (!). Also a su - joeuser as root works fine, so the bash binary itself is working fine. In an act of despair, I changed joeuser's uid to 0 on /etc/passwd, but also didn't work, so it doesn't seem to be anything permission related. Seems that bash is doing some extra checking that sshd didn't like, and blocking the connections for non-root users. Maybe some sort of sanity checking - or terminal emulation - that is triggering the SIGCHLD, but only when called via ssh. I already went through every single item on sshd_config, and also put SSHD in debug mode, but didn't find anything strange. Here's my /etc/ssh/sshd_config: LogLevel DEBUG LoginGraceTime 2m PermitRootLogin yes RSAAuthentication yes PubkeyAuthentication yes AuthorizedKeysFile %h/.ssh/authorized_keys ChallengeResponseAuthentication no UsePAM yes AllowTcpForwarding no ChrootDirectory none Subsystem sftp internal-sftp -f DAEMON -u 000 And here's the output from /usr/syno/sbin/sshd -d, showing the failed attempt of joeuser trying to log in, with /bin/bash as the shell: debug1: Config token is loglevel debug1: Config token is logingracetime debug1: Config token is permitrootlogin debug1: Config token is rsaauthentication debug1: Config token is pubkeyauthentication debug1: Config token is authorizedkeysfile debug1: Config token is challengeresponseauthentication debug1: Config token is usepam debug1: Config token is allowtcpforwarding debug1: Config token is chrootdirectory debug1: Config token is subsystem debug1: HPN Buffer Size: 87380 debug1: sshd version OpenSSH_5.8p1-hpn13v11 debug1: read PEM private key done: type RSA debug1: private host key: #0 type 1 RSA debug1: read PEM private key done: type DSA debug1: private host key: #1 type 2 DSA debug1: read PEM private key done: type ECDSA debug1: private host key: #2 type 3 ECDSA debug1: rexec_argv[0]='/usr/syno/sbin/sshd' debug1: rexec_argv[1]='-d' Set /proc/self/oom_adj from 0 to -17 debug1: Bind to port 22 on ::. debug1: Server TCP RWIN socket size: 87380 debug1: HPN Buffer Size: 87380 Server listening on :: port 22. debug1: Bind to port 22 on 0.0.0.0. debug1: Server TCP RWIN socket size: 87380 debug1: HPN Buffer Size: 87380 Server listening on 0.0.0.0 port 22. debug1: Server will not fork when running in debugging mode. debug1: rexec start in 6 out 6 newsock 6 pipe -1 sock 9 debug1: inetd sockets after dupping: 4, 4 Connection from 127.0.0.1 port 52212 debug1: HPN Disabled: 0, HPN Buffer Size: 87380 debug1: Client protocol version 2.0; client software version OpenSSH_5.8p1-hpn13v11 SSH: Server;Ltype: Version;Remote: 127.0.0.1-52212;Protocol: 2.0;Client: OpenSSH_5.8p1-hpn13v11 debug1: match: OpenSSH_5.8p1-hpn13v11 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.8p1-hpn13v11 debug1: permanently_set_uid: 1024/100 debug1: MYFLAG IS 1 debug1: list_hostkey_types: ssh-rsa,ssh-dss,ecdsa-sha2-nistp256 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: AUTH STATE IS 0 debug1: REQUESTED ENC.NAME is 'aes128-ctr' debug1: kex: client->server aes128-ctr hmac-md5 none SSH: Server;Ltype: Kex;Remote: 127.0.0.1-52212;Enc: aes128-ctr;MAC: hmac-md5;Comp: none debug1: REQUESTED ENC.NAME is 'aes128-ctr' debug1: kex: server->client aes128-ctr hmac-md5 none debug1: expecting SSH2_MSG_KEX_ECDH_INIT debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: KEX done debug1: userauth-request for user joeuser service ssh-connection method none SSH: Server;Ltype: Authname;Remote: 127.0.0.1-52212;Name: joeuser debug1: attempt 0 failures 0 debug1: Config token is loglevel debug1: Config token is logingracetime debug1: Config token is permitrootlogin debug1: Config token is rsaauthentication debug1: Config token is pubkeyauthentication debug1: Config token is authorizedkeysfile debug1: Config token is challengeresponseauthentication debug1: Config token is usepam debug1: Config token is allowtcpforwarding debug1: Config token is chrootdirectory debug1: Config token is subsystem debug1: PAM: initializing for "joeuser" debug1: PAM: setting PAM_RHOST to "localhost" debug1: PAM: setting PAM_TTY to "ssh" debug1: userauth-request for user joeuser service ssh-connection method password debug1: attempt 1 failures 0 debug1: do_pam_account: called Accepted password for joeuser from 127.0.0.1 port 52212 ssh2 debug1: monitor_child_preauth: joeuser has been authenticated by privileged process debug1: PAM: establishing credentials User child is on pid 9129 debug1: Entering interactive session for SSH2. debug1: server_init_dispatch_20 debug1: server_input_channel_open: ctype session rchan 0 win 65536 max 16384 debug1: input_session_request debug1: channel 0: new [server-session] debug1: session_new: session 0 debug1: session_open: channel 0 debug1: session_open: session 0: link with channel 0 debug1: server_input_channel_open: confirm session debug1: server_input_global_request: rtype [email protected] want_reply 0 debug1: server_input_channel_req: channel 0 request pty-req reply 1 debug1: session_by_channel: session 0 channel 0 debug1: session_input_channel_req: session 0 req pty-req debug1: Allocating pty. debug1: session_new: session 0 debug1: session_pty_req: session 0 alloc /dev/pts/1 debug1: server_input_channel_req: channel 0 request shell reply 1 debug1: session_by_channel: session 0 channel 0 debug1: session_input_channel_req: session 0 req shell debug1: Setting controlling tty using TIOCSCTTY. debug1: Received SIGCHLD. debug1: session_by_pid: pid 9130 debug1: session_exit_message: session 0 channel 0 pid 9130 debug1: session_exit_message: release channel 0 debug1: session_by_tty: session 0 tty /dev/pts/1 debug1: session_pty_cleanup: session 0 release /dev/pts/1 Received disconnect from 127.0.0.1: 11: disconnected by user debug1: do_cleanup debug1: do_cleanup debug1: PAM: cleanup debug1: PAM: closing session debug1: PAM: deleting credentials Here you have the full output of sshd -dd, together with ssh -vv. Bash: # bash --version GNU bash, version 3.2.49(1)-release (arm-none-linux-gnueabi) Copyright (C) 2007 Free Software Foundation, Inc. The bash binary was cross compiled from source. I also tried using a pre-compiled binary from the Optware distribution, but had the exact same problem. I checked for missing shared libraries using objdump -x, but they're all there. Any ideas what could be causing this "Permission denied, please try again."? I'm almost diving in the bash source code to investigate, but trying to avoid hours chasing something that may be silly.

  Read the article

• SSH as root using public key still prompts for password on RHEL 6.1

  - by Dean Schulze

  I've generated rsa keys with cygwin ssh-keygen and copied them to the server with ssh-copy-id -i id_rsa.pub [email protected] I've got the following settings in my /etc/ssh/sshd_config file RSAAuthentication yes PubkeyAuthentication yes AuthorizedKeysFile .ssh/authorized_keys PermitRootLogin yes When I ssh [email protected] it still prompts for a password. The output below from /usr/sbin/sshd -d says that a matching keys was found in the .ssh/authorized_keys file, but it still requires a password from the client. I've read a bunch of web postings about permissions on files and directories, but nothing works. Is it possible to ssh with keys in RHEL 6.1 or is this forbidden? The debug output from ssh and sshd is below. $ ssh -v [email protected] OpenSSH_6.1p1, OpenSSL 1.0.1c 10 May 2012 debug1: Connecting to my.ip.address [my.ip.address] port 22. debug1: Connection established. debug1: identity file /home/dschulze/.ssh/id_rsa type 1 debug1: identity file /home/dschulze/.ssh/id_rsa-cert type -1 debug1: identity file /home/dschulze/.ssh/id_dsa type 2 debug1: identity file /home/dschulze/.ssh/id_dsa-cert type -1 debug1: identity file /home/dschulze/.ssh/id_ecdsa type -1 debug1: identity file /home/dschulze/.ssh/id_ecdsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.3 debug1: match: OpenSSH_5.3 pat OpenSSH_5* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_6.1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA 9f:00:e0:1e:a2:cd:05:53:c8:21:d5:69:25:80:39:92 debug1: Host 'my.ip.address' is known and matches the RSA host key. debug1: Found key in /home/dschulze/.ssh/known_hosts:3 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic,password debug1: Next authentication method: publickey debug1: Offering RSA public key: /home/dschulze/.ssh/id_rsa debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic,password debug1: Offering DSA public key: /home/dschulze/.ssh/id_dsa debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic,password debug1: Trying private key: /home/dschulze/.ssh/id_ecdsa debug1: Next authentication method: password Here is the server output from /usr/sbin/sshd -d [root@ga2-lab .ssh]# /usr/sbin/sshd -d debug1: sshd version OpenSSH_5.3p1 debug1: read PEM private key done: type RSA debug1: private host key: #0 type 1 RSA debug1: read PEM private key done: type DSA debug1: private host key: #1 type 2 DSA debug1: rexec_argv[0]='/usr/sbin/sshd' debug1: rexec_argv[1]='-d' debug1: Bind to port 22 on 0.0.0.0. Server listening on 0.0.0.0 port 22. debug1: Bind to port 22 on ::. Server listening on :: port 22. debug1: Server will not fork when running in debugging mode. debug1: rexec start in 5 out 5 newsock 5 pipe -1 sock 8 debug1: inetd sockets after dupping: 3, 3 Connection from 172.60.254.24 port 53401 debug1: Client protocol version 2.0; client software version OpenSSH_6.1 debug1: match: OpenSSH_6.1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.3 debug1: permanently_set_uid: 74/74 debug1: list_hostkey_types: ssh-rsa,ssh-dss debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: client->server aes128-ctr hmac-md5 none debug1: kex: server->client aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST received debug1: SSH2_MSG_KEX_DH_GEX_GROUP sent debug1: expecting SSH2_MSG_KEX_DH_GEX_INIT debug1: SSH2_MSG_KEX_DH_GEX_REPLY sent debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: KEX done debug1: userauth-request for user root service ssh-connection method none debug1: attempt 0 failures 0 debug1: PAM: initializing for "root" debug1: userauth-request for user root service ssh-connection method publickey debug1: attempt 1 failures 0 debug1: test whether pkalg/pkblob are acceptable debug1: PAM: setting PAM_RHOST to "172.60.254.24" debug1: PAM: setting PAM_TTY to "ssh" debug1: temporarily_use_uid: 0/0 (e=0/0) debug1: trying public key file /root/.ssh/authorized_keys debug1: fd 4 clearing O_NONBLOCK debug1: matching key found: file /root/.ssh/authorized_keys, line 1 Found matching RSA key: db:b3:b9:b1:c9:df:6d:e1:03:5b:57:d3:d9:c4:4e:5c debug1: restore_uid: 0/0 Postponed publickey for root from 172.60.254.24 port 53401 ssh2 debug1: userauth-request for user root service ssh-connection method publickey debug1: attempt 2 failures 0 debug1: temporarily_use_uid: 0/0 (e=0/0) debug1: trying public key file /root/.ssh/authorized_keys debug1: fd 4 clearing O_NONBLOCK debug1: matching key found: file /root/.ssh/authorized_keys, line 1 Found matching RSA key: db:b3:b9:b1:c9:df:6d:e1:03:5b:57:d3:d9:c4:4e:5c debug1: restore_uid: 0/0 debug1: ssh_rsa_verify: signature correct debug1: do_pam_account: called Accepted publickey for root from 172.60.254.24 port 53401 ssh2 debug1: monitor_child_preauth: root has been authenticated by privileged process debug1: temporarily_use_uid: 0/0 (e=0/0) debug1: ssh_gssapi_storecreds: Not a GSSAPI mechanism debug1: restore_uid: 0/0 debug1: SELinux support enabled debug1: PAM: establishing credentials PAM: pam_open_session(): Authentication failure debug1: Entering interactive session for SSH2. debug1: server_init_dispatch_20 debug1: server_input_channel_open: ctype session rchan 0 win 1048576 max 16384 debug1: input_session_request debug1: channel 0: new [server-session] debug1: session_new: session 0 debug1: session_open: channel 0 debug1: session_open: session 0: link with channel 0 debug1: server_input_channel_open: confirm session debug1: server_input_global_request: rtype [email protected] want_reply 0 debug1: server_input_channel_req: channel 0 request pty-req reply 1 debug1: session_by_channel: session 0 channel 0 debug1: session_input_channel_req: session 0 req pty-req debug1: Allocating pty. debug1: session_pty_req: session 0 alloc /dev/pts/1 ssh_selinux_setup_pty: security_compute_relabel: Invalid argument debug1: server_input_channel_req: channel 0 request shell reply 1 debug1: session_by_channel: session 0 channel 0 debug1: session_input_channel_req: session 0 req shell debug1: Setting controlling tty using TIOCSCTTY. debug1: Received SIGCHLD. debug1: session_by_pid: pid 17323 debug1: session_exit_message: session 0 channel 0 pid 17323 debug1: session_exit_message: release channel 0 debug1: session_pty_cleanup: session 0 release /dev/pts/1 debug1: session_by_channel: session 0 channel 0 debug1: session_close_by_channel: channel 0 child 0 debug1: session_close: session 0 pid 0 debug1: channel 0: free: server-session, nchannels 1 Received disconnect from 172.60.254.24: 11: disconnected by user debug1: do_cleanup debug1: PAM: cleanup debug1: PAM: deleting credentials

  Read the article

< Previous Page | 137 138 139 140 141 142 143 144 145 146 147 148  | Next Page >