Search Results

Search found 11111 results on 445 pages for 'c mode'.

Page 143/445 | < Previous Page | 139 140 141 142 143 144 145 146 147 148 149 150  | Next Page >

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• Windows Service with Logon a user

  - by David.Chu.ca

  I have a service running in a box with Windows XP and a box of Server (2003). There is one service running in autmactic mode. If I set the log on with a local user, the service will stop running if the user logs off the account from the Windows? In other words, in order to keep the service running, have I to keep the user as login mode? I understand that the service can be set as local system which will not need any one to login as long as the box is powered on. However, the service I need to run has to be running as a local user with the required permissions. The problem I have right now is that the box may reboot itself. If that happens, no one is logged in yet until some one has to log in as the required user. I want to make sure if the required user has to be as a log on user first. If that's the case, any suggestion to deal with unexpected reboot issue?

  Read the article

• (13) Permission denied on Apache CGI attempt

  - by ncv

  I have recently upgraded my Apache2 server, and am now unable to run a CGI app. My logs are showing (13) Permission denied unable to connect to cgi deamon after multiple tries I understand that the error message means Apache is being denied some permission to some file, and I'm stumped as to how to track down and solve the problem. Is the file mentioned in the error message truly the blocked file? Or might the problem be caused by some other needed file? The .cgi file is right where it has always been, under /usr/share. The file ownership (root) and permissions (world readable/executable) are the same as they have always been for the file and its ancestors. The SELinux file labels are unchanged. The SELinux audit log shows no denial associated with Apache nor the CGI program. In case of a donotaudit condition, I enabled audit, but still saw nothing. I switched SELinux into permissive mode briefly, to no avail. I even tried restarting Apache while in permissive mode. This did not solve the problem. Any suggestions on how to solve this problem? I'm tempted to just revert to the older Apache.

  Read the article

• Outlook sends uninvited images as attachments

  - by serhio

  Outlook is always sending along 2 pictures (image001.png and image002.gif) with my mails. Even if I don't attach any images. How do I fix this? Thanks. EDIT - SIGNATURE The HTML of my signature: <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN"> <HTML xmlns:o = "urn:schemas-microsoft-com:office:office"><HEAD><TITLE>Company default Signature</TITLE> <META content="text/html; charset=windows-1252" http-equiv=Content-Type> <META name=GENERATOR content="MSHTML 8.00.6001.18854"></HEAD> <BODY> <DIV align=left><FONT color=navy size=2 face=Arial><SPAN style="FONT-FAMILY: Arial; COLOR: navy; FONT-SIZE: 10pt"> <P class=MsoNormal align=left><BR>Cordialement,&nbsp;</SPAN></FONT><FONT color=navy size=2 face=Arial><SPAN style="FONT-FAMILY: Arial; COLOR: navy; FONT-SIZE: 10pt"><o:p>&nbsp;</o:p></SPAN></FONT></P> <P class=MsoNormal><FONT color=navy size=2 face=Arial><SPAN style="FONT-FAMILY: Arial; COLOR: navy; FONT-SIZE: 10pt">Firstname LASTNAME<BR></SPAN></FONT><FONT color=navy size=2 face=Arial><SPAN style="FONT-FAMILY: Arial; COLOR: navy; FONT-SIZE: 10pt">COMPANY Name<o:p></o:p></SPAN></FONT></P></DIV></BODY></HTML> EDIT 2 - STATIONERY I don't use stationery format: EDIT 3 - HTML If I delete the signature (Ctrl+A, Del) in the HTML mode the images always appear. If I use the signature in text only mode, the images disappears...

  Read the article

• JVM system time runs faster than HP UNIX OS system time

  - by winston

  Hello I have the following output from a simple debug jsp: Weblogic Startup Since: Friday, October 19, 2012, 08:36:12 AM Database Current Time: Wednesday, December 12, 2012, 11:43:44 AM Weblogic JVM Current Time: Wednesday, December 12, 2012, 11:45:38 AM Line 1 was a recorded variable during WebLogic webapp startup. Line 2 was output from database query select sysdate from dual; Line 3 was output from java code new Date() I have checked from shell date command that line 2 output conforms with OS time. The output of line 3 was mysterious. I don't know how it comes from Java VM. On another machine with same setting, the same jsp output like this: Weblogic Startup Since: Tuesday, December 11, 2012, 02:29:06 PM Database Current Time: Wednesday, December 12, 2012, 11:51:48 AM Weblogic JVM Current Time: Wednesday, December 12, 2012, 11:51:50 AM Another machine: Weblogic Startup Since: Monday, December 10, 2012, 05:00:34 PM Database Current Time: Wednesday, December 12, 2012, 11:52:03 AM Weblogic JVM Current Time: Wednesday, December 12, 2012, 11:52:07 AM Findings: the pattern shows that the longer Weblogic startup, the larger the discrepancy of OS time with JVM time. Anybody could help on HP JVM? On HP UNIX, NTP was done daily. Anyway here comes the server versions: HP-UX machinex B.11.31 U ia64 2426956366 unlimited-user license java version "1.6.0.04" Java(TM) SE Runtime Environment (build 1.6.0.04-jinteg_28_apr_2009_04_46-b00) Java HotSpot(TM) Server VM (build 11.3-b02-jre1.6.0.04-rc2, mixed mode) WebLogic Server Version: 10.3.2.0 Java properties java.runtime.name=Java(TM) SE Runtime Environment java.runtime.version=1.6.0.04-jinteg_28_apr_2009_04_46-b00 java.vendor=Hewlett-Packard Co. java.vendor.url=http\://www.hp.com/go/Java java.version=1.6.0.04 java.vm.name=Java HotSpot(TM) 64-Bit Server VM java.vm.info=mixed mode java.vm.specification.vendor=Sun Microsystems Inc. java.vm.vendor="Hewlett-Packard Company" sun.arch.data.model=64 sun.cpu.endian=big sun.cpu.isalist=ia64r0 sun.io.unicode.encoding=UnicodeBig sun.java.launcher=SUN_STANDARD sun.jnu.encoding=8859_1 sun.management.compiler=HotSpot 64-Bit Server Compiler sun.os.patch.level=unknown os.name=HP-UX os.version=B.11.31

  Read the article

• VPN issue: SSTP Service service started and then stopped

  - by Ampersand

  When I was trying to set up a VPN connect on my laptop running Windows 7 Ultimate, I got this error: Network Connections Cannot load the Remote Access Connection Manager service. Error 711: The operation could not finish because it could not start the Remote Access Connection Manager service in time. Please try the operation again. I traced through some service dependencies and discovered that Secure Socket Tunneling Protocol Service was set to Manual. However, when I try to manually start the service, I get: Services The Secure Socket Tunneling Protocol Service on Local Computer started and then stopped. Some services stop automatically if they are not in use by other services or programs. Setting all the services involved to Automatic did not help. SSTP just showed Automatic and Stopped in the Services panel. I found a solution that involved booting in Safe Mode and deleting the contents of C:\Windows\System32\LogFiles\WMI\RtBackup. This solution worked, and I could set up a vpn connection, but only until I rebooted again. TL;DR I'm looking for a way to permanently enable Secure Socket Tunneling Protocol Service and other vpn-related services permanently so I don't have to reboot into safe mode and delete files every time I need to connect to a vpn.

  Read the article

• MacBook Pro (OSX Lion) - shutdown automatically before reaching login screen

  - by mkk

  When I try to lunch my MacBook Pro I can see a progress bar on loading screen. It goes to 1/15 or something like this and then it shut downs - I cannot reach even login screen. It happened to me 2 months ago, I have 'fixed' this by formatting my hard drive and installing OSX (Lion) again. This time I think that situation is a little bit different - I am able to enter single-user mode by pressing cmd + s. I then type /sbin/fsck -yf, I get the error: ** Checking Journaled HFS Plus volume. The volume name is Macintosh HD ** Checking extents overflow file. ** Checking catalog file. Invalid node structure (4, 24704) ** The volume Macintosh HD could not be verified completely. /dev/rdisk0s2 (hfs) EXITED WITH SIGNAL 8 but when I type exit, I can the login screen and I can log in. I tried a lot of things, booting from recovery partition and choosing disk utility to repair the disc, but I get error that it cannot be repaired. I have googled for hours and the only real solution I have found was to buy Disc warrior that might fix the issue. Any other suggestions? Secondary question is what causes this issue? I thought the reason are bad sectors, but Smart Utility haven't found any. I found suggestion that RAM could cause this kind of issue as well, so I downloaded rember and made memory test - all tests passed. Right now I have used my solution of entering single-mode user and then typing exit, however I am not sure how long it will 'work'. Of course I have back-uped what I considered important. Thanks for the help in advance! UPDATE: I guess Smart Utility was not very useful, I mnaged to get input/output error, which I believe is equivalent to bad sector.

  Read the article

• Auto-rebuild RAID6 with MDADM

  - by user65632

  Hello everybody, i'm new in this forum, and because I see that a lot of people get helped here, i'll ask my question here! I have a openSUSE 11.3 Linux computer with 5 disks of 1TB (WD enterprise disks) in it. with mdadm I configured an RAID6 device. Now, after a lot of thorough testing, i've noticed that when the computer goes down unsuspectedly it could happen (1 time out of 10) that while booting, the md0 device isn't recognised, and then the machine goes in "recovery mode", which means that i have to 'CTRL + C' it so it can boot to openSUSE. Once in openSUSE i have to readd the drive manually with 'mdadm /dev/md0 --add /dev/sdX'. After this everything works back fine (after resynching). So my question is: Is there a way to auto-rebuild the RAID6 device when there are problems? and how can I stop this "recovery mode" from happening. Because the computer will be in a place I can't go to, to connect a keyboard, 'CTRL + C' it just to get in openSUSE. If you could help me, I would be a very very very! happy man! :-) thanks in advance! Mikhail

  Read the article

• Is there a Windows 7 compatible IPSec VPN client that allows protocol and port specific rules?

  - by Sani Huttunen

  As the title says, I need to find a IPSec VPN client for Windows 7. On XP and Vista we've used SafeNet SoftRemote in which you can set up rules for specific protocols and ports. But SoftRemote isn't compatible with Windows 7. 172.xxx.xxx.1 TCP 1433 172.xxx.xxx.2 TCP 1433 172.xxx.xxx.10 ALL ... Since the VPN gateway is configured this way the client must mirror these settings. I've tried TheGreenBow, NCP Secure Entry, Cisco VPN Client and Shrew Soft VPN but none of these allows you to configure by protocol and port. Does anyone have any other suggestions? EDIT: Forgot to mention that agressive mode is also a requirement. --UPDATE-- I've got some news... I've managed to get SoftRemote to work on Windows 7 x64 through Windows XP Mode. After scouring all corners of the Internet for idéas I had enough information to construct a working solution. This solution will probably benefit other clients as well! You'll find a post here with detailed instructions of how I went about.

  Read the article

• Appears to be "randomly" switching between the acl matched backend and the default backend

  - by Xoor

  I have HAProxy acting as a proxy in front of: An NGinx instance An in-house load balancer in front of multiple dynamic services exposed with socket.io (websockets) My problem is that from time to time my connections are proxied correctly to my socket.io cluster, and then randomly it fallsback to routing to NGinx which obviously is annoying and meaningless since NGinx isn't mean't to handle the request. This happens when requesting for URLs of the format : http://mydomain.com/backends/* There's an ACL in the HAProxy config to match the '/backends/*' path. Here's a simplified version of my HAProxy config (removed extra unrelated entries and changed names): global daemon maxconn 4096 user haproxy group haproxy nbproc 4 defaults mode http timeout server 86400000 timeout connect 5000 log global #this frontend interface receives the incoming http requests frontend http-in mode http #process all requests made on port 80 bind *:80 #set a large timeout for websockets timeout client 86400000 # Default Backend default_backend www_backend # Loadfire (socket cluster) acl is_loadfire_backends path_beg /backends use_backend loadfire_backend if is_loadfire_backends # NGinx backend backend www_backend server www_nginx localhost:12346 maxconn 1024 # Loadfire backend backend loadfire_backend option forwardfor # This sets X-Forwarded-For option httpclose server loadfire localhost:7101 maxconn 2048 It's really quite confusing for me why the behaviour appears to be "random", since being hard to reproduce it's hard to debug. I appreciate any insight on this.

  Read the article

• Connecting a network printer via a Thecus N2100 - works in Vista, not in Windows 7

  - by Jon Skeet

  I have a Lexmark E250d printer attached to a Thecus N2100 NAS. On Windows Vista I've managed to configure this using an "Internet" printer port with the URL of http://thecus:631/printers/usb-printer. I can add a printer in a similar way in Windows 7, but it never manages to print the test page. If I go to "Configure Port" in Vista, it just has "Security Options" - on Windows 7 it's asking about Raw mode vs LPR mode etc. On Vista I'm using an E250d-specific driver from Lexmark; on Windows 7 there's a Microsoft E250d driver, or a Universal PCL XL driver from Lexmark... I wouldn't expect this different to be related to the problem, but I thought I'd mention it anyway. (Lexmark doesn't have a Windows 7 E250d-specific driver as far as I can see.) Any suggestions? I was thinking of upgrading my main laptop from Vista to Windows 7, but I'd really like to get this sorted first... EDIT: If I connect to http://thecus:631/printers/usb-printer via Chrome while capturing with Wireshark, I get this response: HTTP/1.1 200 OK Date: Wed, 06 Jan 2010 16:47:23 GMT Connection: Keep-Alive Keep-Alive: timeout=60 Content-Language: C Transfer-Encoding: chunked Content-Type: text/html;charset=iso-8859-1 0 No idea what that's meant to be doing... EDIT: On further consultation, this would appear to be the Internet Printing Protocol which is layered on HTTP. Printing a test page successfully from Vista posts to that URL. Will attempt the same on Windows 7...

  Read the article

• How do hdparm's -S and -B options interact?

  - by user697683

  These two options seem confusing. For example: according to the man page -B 254 "does not permit spin-down". However, testing with -B 254 -S 1 the drive does spin down after 5 seconds. -B Query/set Advanced Power Management feature, if the drive supports it. A low value means aggressive power management and a high value means better performance. Possible settings range from values 1 through 127 (which permit spin-down), and values 128 through 254 (which do not permit spin-down). The highest degree of power management is attained with a setting of 1, and the highest I/O performance with a setting of 254. A value of 255 tells hdparm to disable Advanced Power Management altogether on the drive (not all drives support disabling it, but most do). -S Put the drive into idle (low-power) mode, and also set the standby (spindown) timeout for the drive. This timeout value is used by the drive to determine how long to wait (with no disk activity) before turning off the spindle motor to save power. Under such circumstances, the drive may take as long as 30 seconds to respond to a subsequent disk access, though most drives are much quicker. The encoding of the timeout value is somewhat peculiar. A value of zero means "timeouts are disabled": the device will not automatically enter standby mode. Values from 1 to 240 specify multiples of 5 seconds, yielding timeouts from 5 seconds to 20 minutes. Values from 241 to 251 specify from 1 to 11 units of 30 minutes, yielding timeouts from 30 minutes to 5.5 hours. A value of 252 signifies a timeout of 21 minutes. A value of 253 sets a vendor-defined timeout period between 8 and 12 hours, and the value 254 is reserved. 255 is interpreted as 21 minutes plus 15 seconds. Note that some older drives may have very different interpretations of these values.

  Read the article

• Server nearly unusable when doing disk writes

  - by Wikser

  My question closely relates to my last question here on serverfault. I was copying about 5GB from a 10 year old desktop computer to the server. The copy was done in Windows Explorer. In this situation I would assume the server to be bored by the dataflow. But as usual with this server, it really slowed down. At least I could work with the remote session, even there was some serious latency. The copy took its time (20min?). In this time I went to a colleague and he tried to log in in the same server via remote desktop (for some other reason). It took about a minute to get to the login screen, a minute to open the control panel, a minute to open the performance monitor, ... Icons were loading maybe one per second. We saw the following (from memory): CPU: 2% Avg. Queue Length: 50 Pages/sec: 115 (?) There was no other considerable activity on the server. The server seldom serves some ASP.NET pages, which became also very slow in this time. The relevant configuration is as follows: Windows 2003 SEAGATE ST3500631NS (7200 rpm, 500 GB) LSI MegaRAID based RAID 5 4 disks, 1 hot spare Write Through No read-ahead Direct Cache Mode Harddisk-Cache-Mode: off Is this normal behaviour for such a configuration? What measurements could give further clues? Is it reasonable to reduce the priority of such copy I/O and favour other processes like the remote desktop? How would you do that? Many thanks!

  Read the article

• Mac creating files w/ wrong perms on samba share

  - by geoffjentry

  In my group, which is very heterogeneous in terms of machines, we use a samba share to collaborate on files and such. In all but one case, it works as expected (or at least close enough). The one exception is my boss' laptop, a snow leopard macbook air. On his desktop (also snow leopard), if he creates a file it ends up serverside with perms of 774, but when he creates it with the Air, the perms are 644. The key problem is the lack of group write permission on the laptop created files. What's really confusing is that everything that I've looked at on the two machines are identical - same version of OS X, same version of samba (3.0.25b-apple), same settings for the same software, etc. I can't imagine why one machine would be different than the other, but it is. To try to be complete w/ the description, here is the relevant portion of my smb.conf file: comment = my Share path = /path/to/share public = no writeable = yes printable = no force group = myshare directory mask = 0770 create mask = 0770 force create mode = 0770 force directory mode = 0770 EDIT: I looked at three more Macs and all of them worked as expected which leaves this one laptop the true oddball. This wasn't as good as a test as the others though, as they were all leopard.

  Read the article

• Will these instructions work when turning of journaling on a n ext4 SSD?

  - by snowlord

  I have an Acer Aspire One with an SSD for storage. I recently installed Ubuntu on it and chose ext4 for my filesystem. Then I read that journaling on an SSD isn't the best idea, so I will try to disable journaling and I have found these intstructions (from http://fenidik.blogspot.com/2010/03/ext4-disable-journal.html): # Create ext4 fs on /dev/sda10 disk mkfs.ext4 /dev/sda10 # Enable writeback mode. This mode will typically provide the best ext4 performance. tune2fs -o journal_data_writeback /dev/sda10 # Delete has_journal option tune2fs -O ^has_journal /dev/sda10 # Required fsck e2fsck -f /dev/sda10 # Check fs options dumpe2fs /dev/sda10 |more For more performance add fstab opions: data=writeback,noatime,nodiratime i.e: /dev/sda10 /opt ext4 defaults,data=writeback,noatime,nodiratime 0 0 I will use them on my boot partition. Are there any particularly bad parts here, or are there any missing steps? Will my boot partition be fit for being on an SSD after this? Or should I consider switching to ext2, or even reinstall it all and choose ext2 at partitioning time (I'd rather not though, since I've configured quite some stuff already)?

  Read the article

• Ruckus wireless AP and Dell PowerConnect configuration problems

  - by DanielJay

  We are working on trying to get some Ruckus Access Points to work correctly on our network. Currently our network is as follows: VLAN 10 - Servers VLAN 11 – Computers/DHCP VLAN 12 – Voice VLAN 13 – Guest We use Dell PowerConnect 6248P switches for our switches. Port settings are as follows: ZoneDirector 1100 is plugged into this port. Should be accessing the server VLAN and then allowing all other traffic. interface ethernet 1/g2 classofservice trust ip-dscp description 'Ruckus ZoneDirector 1100' switchport mode general switchport general pvid 10 switchport general allowed vlan add 10 switchport general allowed vlan add 11-13 tagged exit Access point is plugged into this port. The port has to be on VLAN 11 in order to get DHCP. interface ethernet 1/g16 classofservice trust ip-dscp description 'Ruckus - IT' switchport mode general switchport general pvid 11 switchport general allowed vlan add 10-12 switchport general allowed vlan add 13 tagged exit If we tag the traffic from the SSID as VLAN 11 data fails. If we leave the SSID tagged as 1 the data flows correctly. Are there problems with passing tagged traffic to untagged ports? We are looking to see what we can do to get the SSID tagged as 11 instead of 1. Any suggestions?

  Read the article

• Broken filesystem on Windows XP / 7 virtual machine

  - by Pekka

  I created a virtual machine with Windows XP as the guest system in Microsoft's Virtual PC that ships along with Windows 7. I then installed Virtualbox and began running the MS machine in it. It worked fine. Then, I accidentally started the machine in Microsoft's Virtual PC again. The screen stayed blank, so after a while, realizing my mistake, I closed the Machine. Since then, the VM won't start any more, claiming massive file system problems. Starting Windows in normal mode results in a SOMETHING_FILESYSTEM blue screen; I can start in protected mode and run a checkdisk. That will fix something on every run, but every time I restart, it will start again. I tried re-booting the VM with the Windows CD and doing a repair install. I didn't watch whether that worked out, but I'm caught in the reset / check disk / reset cycle again. Is there anything VM specific that can still be done? On a physical machine, I would say reformat. Is there any way to get hold of the data on the virtual machine through either Virtual PC or Virtualbox? It was an experimental machine, but I had started entering some data on it that would be nice to recover.

  Read the article

• Installing WinPcap on Windows 8

  - by Dave Robinson

  I know there has been lots of discussion already on installing WinPcap on Windows 8. I'm running the RTM version. I was able to install WinPcap without a hitch by using the Windows 7 compatibility mode. Since then, I've noticed that WinPcap has stopped running and is actually no longer even installed. I tried installing it again, but now it continues to tell me that WinPcap does not work with my version of Windows. Compatibility modes and admin privileges make no difference. The only thing I remember doing to my system was installed 900MBs of Windows Updates. Does anyone have any ideas about what I might do to get WinPcap installed? I've already ensured that the compatibility mode settings I changed were in effect for all users. I've already ensured that "run this program as an administrator" is checked on the compatibility tab for all users. I've also tried installing WinPcap 4.1.2 and 4.1.1. No success with either.

  Read the article

• windows xp blue screen dumping physical memory

  - by dotnet-practitioner

  I get following blue screen after running my laptop for an hour... A problem has been detected and windows has been shut down to prevent damange to your computer. If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to be sure you have adequate disk space. If a driver is identified in the stop message, disable the driver or check with the manufacturer for driver updates. Try changing video adapters. Check with your hardware vendor for any BIOS updates. Disable BIOS memory options such as cashing or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select advanced startup options, and the select safe mode. Technical Information: * STOP 0x0000008E (0xc0000005, 0x805B03F5, 0xF703DC7C, 0x00000000) Beginning dump of physical memory Physical memory dump complete. Contact you system administrator or technical support group for further assistance. so.... if this is a faulty memory.... from where I could buy RAM for following laptop.... TOSHIBA SATELLITE A45-S250 My local Frys store does not carry memory for this laptop.

  Read the article

• How to debug slow queries in Django+Postgres

  - by lacker

  My database queries from Django are starting to take 1-2 seconds and I'm having trouble figuring out why. Not too big a site, about 1-2 requests per second (that hit Django; static files are just served from nginx.) The thing that confuses me is, I can replicate the slowness in the Django shell using debug mode. But when I issue the exact same queries at an sql prompt they are fast. It takes about a second for a query to return, but when I check connection.queries it reports the time as under 10 ms. Here's an example (from the Django shell): >>> p = PlayerData.objects.get(uid="100000521952372") >>> a = time.time(); p.save(); print time.time() - a 1.96812295914 >>> for d in connection.queries: print d["time"] ... 0.002 0.000 0.000 How can I figure out where this extra time is being spent? I'm using Apache+mod_wsgi in daemon mode, but this happens with just the django shell as well, so I figure it is not apache-related.

  Read the article

• Why is my filesystem being mounted read-only in linux?

  - by Tim

  I am trying to set up a small linux system based on Gentoo on a VirtualBox machine, as a step towards deploying the same system onto a low-spec Single Board Computer. For some reason, my filesystem is being mounted read-only. In my /etc/fstab, I have: /dev/sda1 / ext3 defaults 0 0 none /proc proc defaults 0 0 none /sys sysfs defaults 0 0 none /dev/shm tmpfs defaults 0 0 However, once booted /proc/mounts shows rootfs / rootfs rw 0 0 /dev/root / ext3 ro,relatime,errors=continue,barrier=0,data=writeback 0 0 proc /proc proc rw,nosuid,nodev,noexec,relatime 0 0 sysfs /sys sysfs rw,nosuid,nodev,noexec,relatime 0 0 udev /dev tmpfs rw,nosuid,relatime,size=10240k,mode=755 0 0 devpts /dev/pts devpts rw,nosuid,noexec,relatime,gid=5,mode=620 0 0 none /dev/shm tmpfs rw,relatime 0 0 usbfs /proc/bus/usb usbfs rw,nosuid,noexec,relatime,devgid=85,devmode=664 0 0 binfmt_misc /proc/sys/fs/binfmt_misc binfmt_misc rw,nosuid,nodev,noexec,relatime 0 0 (the above may contain errors: there's no practical way to copy and paste) The partition at /dev/hda1 is clearly being mounted OK, since I can read all the data, but it's not being mounted as described in fstab. How might I go about diagnosing / resolving this? Edit: I can remount with mount -o remount,rw / and it works as expected, except that /proc/mounts reports /dev/root mounted at / rather than /dev/sda1 as I'd expect. If I try to remount with mount -a I get mount: none already mounted or /sys busy mount: according to mtab, sysfs is already mounted on /sys Edit 2: I resolved the problem with mount -a (the same error was occuring during startup, it turned out) by changing the sysfs and proc lines to proc /proc proc [...] sysfs /sys sysfs [...] Now mount -a doesn't complain, but it doesn't result in a read-write root partition. mount -o remount / does cause the root partition to be remounted, however.

  Read the article

• Ubuntu 64bit Xen DomU Issues after upgrade from Karmic to Lucid

  - by Shoaibi

  I was upgrading my servers today and it all went fine except the last machine which has the following issues: [Resolved using http://www.ndchost.com/wiki/server-administration/upgrade-ubuntu-pre-10.04#post-1004-upgradefinal-steps] No login prompt on console Done. Begin: Mounting root file system... ... Begin: Running /scripts/local-top ... Done. [ 0.545705] blkfront: xvda: barriers enabled [ 0.546949] xvda: xvda1 [ 0.549961] blkfront: xvde: barriers enabled [ 0.550619] xvde: xvde1 xvde2 Begin: Running /scripts/local-premount ... Done. [ 0.870385] kjournald starting. Commit interval 5 seconds [ 0.870449] EXT3-fs: mounted filesystem with ordered data mode. Begin: Running /scripts/local-bottom ... Done. Done. Begin: Running /scripts/init-bottom ... Done. Also tried by pressing ENTER and CTRL+C many times, no use. Resolved: [/tmp was mounted as noexec, changing that fix it]: I get errors when i try to re-install udev in single user mode: Unpacking replacement udev ... Processing triggers for ureadahead ... ureadahead will be reprofiled on next reboot Processing triggers for man-db ... Setting up udev (151-12.1) ... udev start/running, process 1003 Removing `local diversion of /sbin/udevadm to /sbin/udevadm.upgrade' update-initramfs: deferring update (trigger activated) Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-2.6.32-25-server /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/local-premount/fixrtc: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/local-premount/ntfs_3g: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/local-premount/resume: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/nfs-top/udev: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/panic/console_setup: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/init-top/all_generic_ide: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/init-top/blacklist: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/init-top/udev: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/init-bottom/udev: Permission denied /usr/sbin/mkinitramfs: 329: /tmp/mkinitramfs_yuuTSc/scripts/local-bottom/ntfs_3g: Permission denied

  Read the article

• What is the difference between the Linux and Linux LVM partition type?

  - by ujjain

  Fdisk shows multiple partition types. What is the difference between choosing 83) Linux and 8e) Linux LVM? Choosing 83) Linux also works fine for using LVM, even creating a physical volume on /dev/sdb without a partition table works. Does picking a partition type in fdisk really matter? What is the difference in picking Linux or Linux LVM as partition type? [root@tst-01 ~]# fdisk /dev/sdb WARNING: DOS-compatible mode is deprecated. It's strongly recommended to switch off the mode (command 'c') and change display units to sectors (command 'u'). Command (m for help): l 0 Empty 24 NEC DOS 81 Minix / old Lin bf Solaris 1 FAT12 39 Plan 9 82 Linux swap / So c1 DRDOS/sec (FAT- 2 XENIX root 3c PartitionMagic 83 Linux c4 DRDOS/sec (FAT- 3 XENIX usr 40 Venix 80286 84 OS/2 hidden C: c6 DRDOS/sec (FAT- 4 FAT16 <32M 41 PPC PReP Boot 85 Linux extended c7 Syrinx 5 Extended 42 SFS 86 NTFS volume set da Non-FS data 6 FAT16 4d QNX4.x 87 NTFS volume set db CP/M / CTOS / . 7 HPFS/NTFS 4e QNX4.x 2nd part 88 Linux plaintext de Dell Utility 8 AIX 4f QNX4.x 3rd part 8e Linux LVM df BootIt 9 AIX bootable 50 OnTrack DM 93 Amoeba e1 DOS access a OS/2 Boot Manag 51 OnTrack DM6 Aux 94 Amoeba BBT e3 DOS R/O b W95 FAT32 52 CP/M 9f BSD/OS e4 SpeedStor c W95 FAT32 (LBA) 53 OnTrack DM6 Aux a0 IBM Thinkpad hi eb BeOS fs e W95 FAT16 (LBA) 54 OnTrackDM6 a5 FreeBSD ee GPT f W95 Ext'd (LBA) 55 EZ-Drive a6 OpenBSD ef EFI (FAT-12/16/ 10 OPUS 56 Golden Bow a7 NeXTSTEP f0 Linux/PA-RISC b 11 Hidden FAT12 5c Priam Edisk a8 Darwin UFS f1 SpeedStor 12 Compaq diagnost 61 SpeedStor a9 NetBSD f4 SpeedStor 14 Hidden FAT16 <3 63 GNU HURD or Sys ab Darwin boot f2 DOS secondary 16 Hidden FAT16 64 Novell Netware af HFS / HFS+ fb VMware VMFS 17 Hidden HPFS/NTF 65 Novell Netware b7 BSDI fs fc VMware VMKCORE 18 AST SmartSleep 70 DiskSecure Mult b8 BSDI swap fd Linux raid auto 1b Hidden W95 FAT3 75 PC/IX bb Boot Wizard hid fe LANstep 1c Hidden W95 FAT3 80 Old Minix be Solaris boot ff BBT 1e Hidden W95 FAT1 Command (m for help):

  Read the article

• Samba Public and "Dropbox" folder

  - by cb0

  I want to create a special Group Directory structure for my Users. /home/groupA <-- home folder for groupA where every user of groupA can create/edit/delete files /home/groupA/Public <-- Public Folder where every user can read files /home/groupA/Public/Dropbox <-- Folder where every user can write files but only users of groupA can access this directory and create/edit/delete files Now I have: 4 drwxrwx--t 10 nobody groupA 4096 Feb 18 15:44 /home/groupA 4 drwxrwxr-x 7 nobody groupA 4096 Feb 18 15:40 /home/groupA/Public/ 4 drwxrwx-w- 10 nobody groupA 4096 Feb 18 15:55 /home/groupA/Public/Dropbox My smc.confcontains the following entrys [groupA] path = /home/groupA comment = Folder for users of groupA browseable = yes read only = no create mask = 0770 directory mask = 0770 force group = groupA [groupA Public] path = /home/groupA/Public comment = Admins Public Browseable = yes write list = @groupA create mask = 0775 directory mask = 0775 [groupA DropBox] path = /home/groupA/Public/Dropbox comment = groupA Dropbox read only = no valid users = @groupA browseable = yes inherit owner = yes directory mode = 3770 force directory mode = 3770 The working part is: Users of groupA can access and fully use /home/groupA All Users can access /home/groupA/Public/ and read the files from there. My problem is that all users, even those who are not in groupA can access the /home/groupA/Public/Dropbox and see all files. I just want them to be able to put files in there but not see the content of the folder and prohibit them from deleting any files in there. Does anybody have a clue what could be the problem and how I can fix it ?

  Read the article

• .ashx cannot find type error on IIS7 , no problems on webdev server

  - by Aivan Monceller

  I am trying to make AspNetComet.zip work on IIS7 (a simple comet chat implementation) Here is a portion of my web.config. <system.web> <httpHandlers> <add verb="POST" path="DefaultChannel.ashx" type="Server.Channels.DefaultChannelHandler, Server"/> </httpHandlers> </system.web> <system.webServer> <handlers> <add name="DefaultChannelHandler" verb="POST" path="DefaultChannel.ashx" type="Server.Channels.DefaultChannelHandler, Server"/> </handlers> </system.webServer> When I publish the website on my localhost IIS7 I receive an error: POST http://localhost/DefaultChannel.ashx 500 Internal Server Error Could not load type 'Server.Channels.DefaultChannelHandler The target framework of this project is .Net 2.0 I tried the Classic and Integrated Mode application pool for .Net 2.0 with no luck. I also tried converting the project to 4.0 and tried the Classic and Integrated Mode application pool for .Net 4.0 with no luck. I also tried adding the managed handler through IIS Manager's Handler Mappings. If you have time please download the source (184kb) to reproduce the problem on your own machine. The zip contains a VS2010 solution (.Net 2.0). You could also try to convert this to .Net 4.0 I am using Windows 7 anyway if that matters. If you need more details, please drop your comments below. This is working fine by the way on my webdev server.

  Read the article

< Previous Page | 139 140 141 142 143 144 145 146 147 148 149 150  | Next Page >