Search Results

Search found 87901 results on 3517 pages for 'exchange server'.

Page 144/3517 | < Previous Page | 140 141 142 143 144 145 146 147 148 149 150 151  | Next Page >

• Multihomed Windows server and DNS resolution

  - by mpkilroy

  I have a Windows 2008 server with two IP addresses assigned to a single NIC. The DNS settings are setup to register the connections's addresses on the DNS server. nslookup shows both IP addresses for the server name. How is name resolution done in this case, i.e. which IP address does the DNS server return for a host lookup? Or does it return both, and the client selects one of the addresses?

  Read the article

• "Sent on behalf" not appearing when delegates sending mails

  - by New Steve

  Ringo is a delegate of Paul's mailbox in Exchange, but when Ringo sends mail from Paul's mailbox, the recipient sees "Paul" in the sender field, rather than "Paul Sent On Behalf Of Ringo" Paul has set "Editor" permissions for Ringo to his mailbox, and Ringo has been granted "Send on behalf of" permissions in Exchange. Ringo did at one time have "Send As" permissions for Paul's mailbox in Exchange, but this has since been removed. This is also the case for all other delegates to Paul's mailbox. How do I make it so that emails sent by Paul's delegates show the "Sent On Behalf Of" information in the Sender field? Using Exchange Server 2007 and Microsoft Office Outlook 2007

  Read the article

• Peforming an Audit for SQL Server 2008

  - by Nai

  Hi all, Do you guys have any good step by step type links for performing an SQL Server 2008 Performance Audit? I know Brad McGehee has written extensively on this but for SQL Server 2005 over at http://www.sql-server-performance.com. But are any such articles for SQL Server 2008? Thanks!

  Read the article

• Windows Server 2008 R2 network adapter stops working, requires hard reboot

  - by Geoff Dalgas

  TL;DR version: Turns out this was a Windows Server 2008 R2 kernel networking bug. After siccing Microsoft support on it, we (eventually) got an unpublished kernel hotfix from Microsoft to address it. If you, too, are experiencing mysterious low-level network driver failures requiring a reboot/bluescreen cycle, you might want that hotfix (or maybe Service Pack 1 whenever it is released, too.) We have been using HAProxy along with heartbeat from the Linux-HA project. We are using two linux instances to provide a failover. Each server has with their own public IP and a single IP which is shared between the two using a virtual interface (eth1:1) at IP: 69.59.196.211 The virtual interface (eth1:1) IP 69.59.196.211 is configured as the gateway for the windows servers behind them and we use ip_forwarding to route traffic. We are experiencing an occasional network outage on one of our windows servers behind our linux gateways. HAProxy will detect the server is offline which we can verify by remoting to the failed server and attempting to ping the gateway: Pinging 69.59.196.211 with 32 bytes of data: Reply from 69.59.196.220: Destination host unreachable. Running arp -a on this failed server shows that there is no entry for the gateway address (69.59.196.211): Interface: 69.59.196.220 --- 0xa Internet Address Physical Address Type 69.59.196.161 00-26-88-63-c7-80 dynamic 69.59.196.210 00-15-5d-0a-3e-0e dynamic 69.59.196.212 00-21-5e-4d-45-c9 dynamic 69.59.196.213 00-15-5d-00-b2-0d dynamic 69.59.196.215 00-21-5e-4d-61-1a dynamic 69.59.196.217 00-21-5e-4d-2c-e8 dynamic 69.59.196.219 00-21-5e-4d-38-e5 dynamic 69.59.196.221 00-15-5d-00-b2-0d dynamic 69.59.196.222 00-15-5d-0a-3e-09 dynamic 69.59.196.223 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 225.0.0.1 01-00-5e-00-00-01 static On our linux gateway instances arp -a shows: peak-colo-196-220.peak.org (69.59.196.220) at <incomplete> on eth1 stackoverflow.com (69.59.196.212) at 00:21:5e:4d:45:c9 [ether] on eth1 peak-colo-196-215.peak.org (69.59.196.215) at 00:21:5e:4d:61:1a [ether] on eth1 peak-colo-196-219.peak.org (69.59.196.219) at 00:21:5e:4d:38:e5 [ether] on eth1 peak-colo-196-222.peak.org (69.59.196.222) at 00:15:5d:0a:3e:09 [ether] on eth1 peak-colo-196-209.peak.org (69.59.196.209) at 00:26:88:63:c7:80 [ether] on eth1 peak-colo-196-217.peak.org (69.59.196.217) at 00:21:5e:4d:2c:e8 [ether] on eth1 Why would arp occasionally set the entry for this failed server as <incomplete>? Should we be defining our arp entries statically? I've always left arp alone since it works 99% of the time, but in this one instance it appears to be failing. Are there any additional troubleshooting steps we can take help resolve this issue? THINGS WE HAVE TRIED I added a static arp entry for testing on one of the linux gateways which still didn't help. root@haproxy2:~# arp -a peak-colo-196-215.peak.org (69.59.196.215) at 00:21:5e:4d:61:1a [ether] on eth1 peak-colo-196-221.peak.org (69.59.196.221) at 00:15:5d:00:b2:0d [ether] on eth1 stackoverflow.com (69.59.196.212) at 00:21:5e:4d:45:c9 [ether] on eth1 peak-colo-196-219.peak.org (69.59.196.219) at 00:21:5e:4d:38:e5 [ether] on eth1 peak-colo-196-209.peak.org (69.59.196.209) at 00:26:88:63:c7:80 [ether] on eth1 peak-colo-196-217.peak.org (69.59.196.217) at 00:21:5e:4d:2c:e8 [ether] on eth1 peak-colo-196-220.peak.org (69.59.196.220) at 00:21:5e:4d:30:8d [ether] PERM on eth1 root@haproxy2:~# arp -i eth1 -s 69.59.196.220 00:21:5e:4d:30:8d root@haproxy2:~# ping 69.59.196.220 PING 69.59.196.220 (69.59.196.220) 56(84) bytes of data. --- 69.59.196.220 ping statistics --- 7 packets transmitted, 0 received, 100% packet loss, time 6006ms Rebooting the windows web server solves this issue temporarily with no other changes to the network but our experience shows this issue will come back. Swapping network cards and switches I noticed the link light on the port of the switch for the failed windows server was running at 100Mb instead of 1Gb on the failed interface. I moved the cable to several other open ports and the link indicated 100Mb for each port that I tried. I also swapped the cable with the same result. I tried changing the properties of the network card in windows and the server locked up and required a hard reset after clicking apply. This windows server has two physical network interfaces so I have swapped the cables and network settings on the two interfaces to see if the problem follows the interface. If the public interface goes down again we will know that it is not an issue with the network card. (We also tried another switch we have on hand, no change) Changing network hardware driver versions We've had the same problem with the latest Broadcom driver, as well as the built-in driver that ships in Windows Server 2008 R2. Replacing network cables As a last ditch effort we remembered another change that occurred was the replacement of all of the patch cords between our servers / switch. We had purchased two sets, one green of lengths 1ft - 3ft for the private interfaces and another set of red cables for the public interfaces. We swapped out all of the public interface patch cables with a different brand and ran our servers without issue for a full week ... aaaaaand then the problem recurred. Disable checksum offload, remove TProxy We also tried disabling TCP/IP checksum offload in the driver, no change. We're now pulling out TProxy and moving to a more traditional x-forwarded-for network arrangement without any fancy IP address rewriting. We'll see if that helps. Switch Virtualization providers On the off chance this was related to Hyper-V in some way (we do host Linux VMs on it), we switched to VMWare Server. No change. Switch host model We've reached the end of our troubleshooting rope and are now formally involving Microsoft support. They recommended changing the host model: http://en.wikipedia.org/wiki/Host_model http://technet.microsoft.com/en-us/magazine/2007.09.cableguy.aspx We did that, and.. we'll see.

  Read the article

• How do I delay email delivery using Entourage 2008 with Exchange, e.g. using the X.400 Deferred-Delivery header?

  - by Matt McClure

  I'd like to delay the delivery of email that I send so that I can time delivery when the recipient is unlikely to be reading email and I can reduce the likelihood of getting into a chat-like conversation. I'm using Entourage 2008 and Exchange hosted by Rackspace. I tried naively adding a Deferred-Delivery header after reading http://www.faqs.org/rfcs/rfc2156.html and www.itu.int/rec/T-REC-F.400-199906-I/en , but my mail was delivered immediately. Ideally the delay would occur on the MTA instead of my MUA so that delivery would still occur even if my laptop were disconnected from the network at the delivery time I specify. My best workaround at the moment is to habitually use Entourage's Send Later button when composing mail and then click Send/Receive at the end of the day. This is less than ideal because recipients are often reading mail at the end of my day, and I often get immediate replies. Matt

  Read the article

• "Sent on behalf" not appearing when delegates sending mails

  - by New Steve

  Ringo is a delegate of Paul's mailbox in Exchange, but when Ringo sends mail from Paul's mailbox, the recipient sees "Paul" in the sender field, rather than "Paul Sent On Behalf Of Ringo" Paul has set "Editor" permissions for Ringo to his mailbox, and Ringo has been granted "Send on behalf of" permissions in Exchange. Ringo did at one time have "Send As" permissions for Paul's mailbox in Exchange, but this has since been removed. This is also the case for all other delegates to Paul's mailbox. How do I make it so that emails sent by Paul's delegates show the "Sent On Behalf Of" information in the Sender field? Using Exchange Server 2007 and Microsoft Office Outlook 2007

  Read the article

• Would an invalid certificate cause an 0x8004010F sync error?

  - by hydroparadise

  We just migrated from Exchange 2003 to 2007 which was a combo primary AD/DNS server and it has not gone smoothly. We are now down to getting a new certificate (a bureaucratic process thats out of my hands) and users getting the 0x8004010F sync issue. We are only using Outlook 2007 as our email client and the sync error appears exactly as so: 9:21:44 Synchronizer Version 12.0.6562 9:21:44 Synchronizing Mailbox '<User>' 9:21:44 Done 9:21:44 Microsoft Exchange offline address book 9:21:44 0X8004010F Now, I have read a number of technet articles on this issue anywhere from adding an A record in the DNS for autodiscover.domain.com to syncing the old OAD to the new OAD. In otherwords, theres lots of thing to try, but trial and error at this point might be hazardous to ther server's health and I am trying to narrow down the list of things to try. What has me thinking that the sync error could be related to the certificate is an event error message that says the following: Microsoft Exchange could not find a certificate that contains the domain name mail.ccufl.org in the personal store on the local computer. Therefore, it is unable to support the STARTTLS SMTP verb for the connector Internet Mail with a FQDN parameter of mail.ccufl.org. If the connector's FQDN is not specified, the computer's FQDN is used. Verify the connector configuration and the installed certificates to make sure that there is a certificate with a domain name for that FQDN. If this certificate exists, run Enable-ExchangeCertificate -Services SMTP to make sure that the Microsoft Exchange Transport service has access to the certificate key. I am not fully clear on how the Exchange Transport Service is related to Syncronization, but my hunch is that it probably not related to there not being a valid certificate. So to recap, would an invalid certificate cause an 0x8004010F sync error?

  Read the article

• VPN clients under PROXY SERVER

  - by Kumar P

  I want to set proxy server for my windows xp desktops. Currently using Windows 2003 as server. But client machines using VPN clients for our work. I installed and run FREEPROXY for proxy connections. But after i installed proxy, i can't connect VPN. What can i do here for setup proxy server with vpn connection. If change server from windows to linux, i am ready for it too.

  Read the article

• Email hosting on home's Windows server 2003

  - by klay

  Hi guys, I am new to Server management, I have a static Ip address and I bought recently a domain name, I configure the domain name to target my Ip address. I am running windows server 2003 standard. what are the steps to host my email adresses? Do I need to buy anything else, or what I have is enough (static ip address, domain name, win server 2003, exchange server 2003) ?? thanks Guys

  Read the article

• Scripted forwarding for Outlook 2003

  - by John Gardeniers

  We have a staff member in sales who has gone onto a 4 day week (getting ready for retirement), so each Thursday afternoon her email needs to be forwarded to another user and each Friday afternoon it needs to be set back. I'm using the VBS script below to do this, run via the Task Scheduler. Although the script appears to do it's job, based on what I see when I view the user's Exchange settings, Exchange doesn't always recognise that the setting has changed. e.g. Last Thursday the forwarding was a enabled and worked correctly. On Friday the script did it's thing to clear the forwarding but Exchange continued to forward messages all weekend. I found that I can force Exchange to honour the changed setting be merely opening and closing the user's properties in ADUC. Of course I don't want to have to do that. Is there a non-manual way I can have Exchange read and honour the setting? The script (VBS): ' Call this script with the following parameters: ' ' SrcUser - The logon ID of the suer who's account is to be modified ' DstUser - The logon account of the person to who mail is to be forwarded ' Use "reset" to clear the email forwarding SrcUser = WScript.Arguments.Item(0) DstUser = WScript.Arguments.Item(1) SourceUser = SearchDistinguishedName(SrcUser) 'The user login name Set objUser = GetObject("LDAP://" & SourceUser) If DstUser = "reset" then objUser.PutEx 1, "altRecipient", "" Else ForwardTo = SearchDistinguishedName(DstUser)' The contact common name objUser.Put "AltRecipient", ForwardTo End If objUser.SetInfo Public Function SearchDistinguishedName(ByVal vSAN) Dim oRootDSE, oConnection, oCommand, oRecordSet Set oRootDSE = GetObject("LDAP://rootDSE") Set oConnection = CreateObject("ADODB.Connection") oConnection.Open "Provider=ADsDSOObject;" Set oCommand = CreateObject("ADODB.Command") oCommand.ActiveConnection = oConnection oCommand.CommandText = "<LDAP://" & oRootDSE.get("defaultNamingContext") & ">;(&(objectCategory=User)(samAccountName=" & vSAN & "));distinguishedName;subtree" Set oRecordSet = oCommand.Execute On Error Resume Next SearchDistinguishedName = oRecordSet.Fields("DistinguishedName") On Error GoTo 0 oConnection.Close Set oRecordSet = Nothing Set oCommand = Nothing Set oConnection = Nothing Set oRootDSE = Nothing End Function

  Read the article

• How to recover a MySQL InnoDB table?

  - by Kau-Boy

  When I try to launch the Plesk administration page of you server I get the following error: ERROR: PleskMainDBException MySQL query failed: MySQL server has gone away The MySQL Server is working well. Although it seems that the plesk database is somehow corrupt and any action on this database results in a restart of the mysql process, so even queries to other databases on the same MySQL server will be lost. If I try to connect to the plesk database using phpMyAdmin, I can only see the number of tables, the database had originally. But I am not able to open the tables listing. As soon as I try it, the mysql process crashes again. Trying to connect to the database using ssh works. I can even run a SELECT statement against any table an get a result. I don't know if it is an plesk error or an error of the psa database or even the MySQL server. Can you give me any tips on how to recover the plesk system. Should I try to repair the Plesk installation before. And if so, how can I do it and will all my settings get lost doing it? EDIT: Trying to dump the database, I get the following error: mysqldump: Got error: 2013: Lost connection to MySQL server during query when using LOCK TABLES EDIT: I could find out, that the table 'data_bases' is responsible for the crash of the MySQL server process. But trying to repair it using a REPAIR TABLE statement doesn't work. EDIT: I now dropped the whole database and restored it from a dump. But why I try to recover the data_bases table I get the following error: ERROR 1005 (HY000) at line 24: Can't create table './psa/data_bases.frm' (errno: 121) I am not able to create the table again. Somewhere in the MySQL system there is still some information about this table. I tested the same thing locally. If I just delete the table files and then try to create the table again I get the same error. If I drop the table through MySQL, I can create the table again afterwards. But trying to drop the table using MySQL the whole MySQL system crashed. Is there any way to solve that issue?

  Read the article

• Host a subdomain from an IIS7 server on another server

  - by brennanmur

  I am running a network with two server, one running SBS 2008 which hosts a majority of the network services (DNS, DHCP, Exchange, IIS, DC, AD...), including the primary webpage at mydomain.com. The other server is a linux box running an apache web server. I'm trying to set the apache server to host the site site2.mydomain.com. I have changed the DNS settings on the first server so that site2.mydomain.com can be accessed from the internal network, but I cannot access site2.mydomain.com from the internet. I have tried using server farms and application request routing cache, as described on this page, http://forums.iis.net/t/1156458.aspx, but I still can't access site2.mydomain.com from the internet. I don't have much experience with web servers, I usually just administer local networks, so I'm not sure if I'm going about this the right way. Any help or suggestions would be much appreciated.

  Read the article

• Why can't I connect to remote Microsoft SQL Server through SSH tunnel?

  - by Alexander

  I have at home a D-Link DIR-615 C1 router with DD-WRT. I set up the SSH server on the router, and log on through an SSH2-RSA passphrase-protected key. That router is the gateway between the local network and the internet. One of the computers on that network has Microsoft SQL Server 2008 installed, with TCP/IP protocol enabled through port 1433. I've set up port forwarding on the router, so that remote connections are possible and are, in fact, working (some developers log on remotely without problems). I am part of another network, that has internet access through a proxy server, which only has ports 80 and 443 opened. I can't connect to that MSSQL server on that remote server because 1433 port is closed on this network. I connected (using Putty) through 443 port to my router's SSH server, and set up 2 tunnels. One is for RDP (3389), and it's working. The other is for 1433 port, to connect to the server. I can't connect through the SSH tunnel to the MS SQL Server, neither through telnet, or through GUI clients. Am I missing something? Additional details: on connect, I get this error from SQL Server Management Studio: TITLE: Connect to Server Cannot connect to localhost:14330. ADDITIONAL INFORMATION: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (Microsoft SQL Server, Error: 3) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&EvtSrc=MSSQLServer&EvtID=3&LinkId=20476 BUTTONS: OK The tunnel is configured like this: L14330 192.168.0.103:1433 192.168.0.103 is the permanent address of the SQL Server on the LAN. I also successfully forwarded TCP traffic of 3389 port to that IP, so tunneling is working to that IP address. When connecting without tunnel, through Microsoft SQL Server Management Studio, using the same method the connection establishes. Too bad my proxy doesn't allow 1433 port traffic, I wouldn't have this headache.

  Read the article

• Outlook items suddenly disapears from inbox after synchronization

  - by Jan Šotola

  We had some disk problems on Exchange server. We had to fix the Exchange 2007 using eseutil. Everything works fine excpet of following problem with one e-mail account: All inbox messages of mentioned e-mail account are fully accessible through the OWA. When any user creates new Outlook profile (using .OST mode) and starts synchronizing, all inbox messages are visible in the Outlook's inbox folder untill the Inbox synchronizing is completed. Once the synchronizing progress bar reaches 100% (and the Outlook starts synchronizing Sent items or another folder), most of messages disappears from the inbox view of the Outlook. The .OST file size does not reduce. New mails (delivered after Exchange server crash) remains all in the inbox. There is no special view or filter applied in the Outlook. The problem has been reproduced on two different computers (Vista+Office2007, Win7+Office2010). We assume there is some problem on the Exchange server but we don't know how to fix it. Can anybody give us some advice?

  Read the article

• Port forwarding with Windows Server 2008

  - by uttt

  I have Windows 2008 server. It works as a mail, ftp, web server. In my LAN there is other server and i want to reach this server with RDC from outside my lan, (example: domail.com:5555 - 192.168.0.2:3389). Is there any solution to forward this port using Windows Firewall?

  Read the article

• Why can't I connect to remote Microsoft SQL Server through SSH tunnel?

  - by Alexander

  I have at home a D-Link DIR-615 C1 router with DD-WRT. I set up the SSH server on the router, and log on through an SSH2-RSA passphrase-protected key. That router is the gateway between the local network and the internet. One of the computers on that network has Microsoft SQL Server 2008 installed, with TCP/IP protocol enabled through port 1433. I've set up port forwarding on the router, so that remote connections are possible and are, in fact, working (some developers log on remotely without problems). I am part of another network, that has internet access through a proxy server, which only has ports 80 and 443 opened. I can't connect to that MSSQL server on that remote server because 1433 port is closed on this network. I connected (using Putty) through 443 port to my router's SSH server, and set up 2 tunnels. One is for RDP (3389), and it's working. The other is for 1433 port, to connect to the server. I can't connect through the SSH tunnel to the MS SQL Server, neither through telnet, or through GUI clients. Am I missing something? Additional details: on connect, I get this error from SQL Server Management Studio: TITLE: Connect to Server Cannot connect to localhost:14330. ADDITIONAL INFORMATION: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (Microsoft SQL Server, Error: 3) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&EvtSrc=MSSQLServer&EvtID=3&LinkId=20476 BUTTONS: OK The tunnel is configured like this: L14330 192.168.0.103:1433 192.168.0.103 is the permanent address of the SQL Server on the LAN. I also successfully forwarded TCP traffic of 3389 port to that IP, so tunneling is working to that IP address. When connecting without tunnel, through Microsoft SQL Server Management Studio, using the same method the connection establishes. Too bad my proxy doesn't allow 1433 port traffic, I wouldn't have this headache.

  Read the article

• How to check database has not been unmounted/ marked for overwrite

  - by RPS

  Hi When restoring Exchange with use of VSS API try to catch errors in cases: 1) when restoring database has not been unmounted Exchange 2010 generate error on PreRestore call and write error to Windows Application log -all ok , but for Exchange2007 PreRestore succeded and write error toWindows Application log only 2)when restored database has been unmounted but has not been marked for overwrite Exchange 2007/2010 generate error to Windows Application log but PreRestore call succeded How can I know from application (via VSS API - not from Windows Application log) that error has happend (database has not been unmounted and has not been marked for overwrite. ) Thanks

  Read the article

• Remote script execution on Windows 2003 server - alternatives to PSEXEC

  - by chickeninabiscuit

  We are wanting to deploy our application to our Test server from our Hudson server. I'd like to be able to have hudson copy the application files and start a script that would run locally on our Test server. We can't use psexec because of a cross domain policy. Currently we are doing this manually, by RDPing to the Test server and checking out the code from subversion manually. Are there alternatives to PSExec that can bypass the cross domain policy problem?

  Read the article

• Trouble creating FTP in Server 2008

  - by Saariko

  I have been trying to create an FTP server on my new Server 2008. I have been following both (very detailed and highly published here guides) For setting up using IIS Manager http://learn.iis.net/page.aspx/321/configure-ftp-with-iis-7-manager-authentication/ and For anonymous FTP http://www.trainsignaltraining.com/windows-server-2008-ftp-iis7 I am able to log as an anonymous user. My need is to use a named user, so I need to use the IIS Manager. I get error 530 when trying to log as a user. Connected to 127.0.0.1. 220 Microsoft FTP Service User (127.0.0.1:(none)): ftpmanager 331 Password required for ftpmanager. Password: 530-User cannot log in. Win32 error: Logon failure: unknown user name or bad password. Error details: Filename: Error: 530 End Login failed. ftp> I can not learn from this message anything. My password is set to: 1234 (so I don't think I make a mistake here - testing purposes only ofc) Thank you. Note - I went over other posts on SE that I read, and couldn't get the result: IIS7 Windows Server 2008 FTP -> Response: 530 User cannot log in. FTP Error 530, User cannot log in, home directory inaccessible. Having trouble setting up FTP server on Windows Server 2008 EDIT I think I found some errors with the physical path. Going to Basic settings, and Test Connection on the physical path, gave me the following error: The server is configured to use pass-through authentication with a built-in account to access the specified physical path. However, IIS Manager cannot verify whether the built-in account has access. Make sure that the application pool identity has Read access to the physical path. If this server is joined to a domain, and the application pool identity is NetworkService or LocalSystem, verify that \$ has Read access to the physical path. Then test these settings again. I am not sure which/whom should get access to the Root folder !? I want to point out, I managed to login with a domain user (change authorization and authentication methods) but this is NOT the requested solution. I checked to make sure that the FTP, folders, access is working properly. I am bit lost here. ==== More tries: I have enabled another Allow rule for ALL Users. I still get the same error. It seems that it doesn't matter if i use a correct or wrong password, I still get Error 530.

  Read the article

• Windows Server 2008 R2 loses ability to connect to network share

  - by JamesB

  I could sure use some help with this one: I've got two Windows Server 2008 R2 x64 Terminal Servers, as well as several 2003 servers (DNS / Wins / AD / DC). On the two 2008 boxes, every now and then they will get in this mode where you can't map a drive to a random server. I say random server because it's not always the same server that you can't map to. Here is a summary of what I can and can't do: net view \\servername Sometimes this works, sometimes it does not. net view \\FQDN This always works. net view \\IPAddress This always works. ping servername Sometimes this works, sometimes it does not. ping FQDN This always works. ping IPAddress This always works. I've been looking all over for a solution to this. It sure seems like Microsoft would have a hotfix by now. The kicker to this is that it sometimes works great, especially after a reboot. It may run for 2 weeks just fine, but all of a sudden it will fail to resolve the remote server name. It will then be this way for a few days, then it might start working again. Also, while it's in the mode of not working, the other servers have no problem getting there. It's just these 2008 R2 Terminal Servers. Setting a static entry in the Hosts file and LMHosts does not make it work. All servers have static IPs and they are registered in DNS and Wins just fine. Here is a long thread on MS Technet of the exact same problem, but they don't have a good solution. Here is their workaround (It was from June of 2010): Good news - a hotfix is in the works and a workaround has been identified: Root cause is that since this is SMB1 all user sessions are on a single TCP connection to the remote server. The first user to initiate a connection to the remote SMB server has their logon-ID added to the structure defining the connection. If that user logs off all subsequent uses of that TCP session fail as the logon-id is no longer valid. As a workaround for now to keep the issue from happening you will want to have the user not logoff the Terminal Server only disconnect their sessions. Any word from anyone out there about a solution? Any help would sure be appreciated. Thanks, James

  Read the article

• Rolling back Server edition from GRUB List (Ubuntu)

  - by A.Rashad

  I seems i did some mistake, and installed Ubuntu server on my home based ubuntu box. and the problem is that GRUB places the server edition as a priority boot in the menu, especially when I upgrade the kernel or the release. How can I remove the server from the GRUB menu permanently? can I un-install Ubuntu server edition?

  Read the article

• WGet from one site on a server to another site on the same server

  - by JoshReedSchramm

  Hey all, I've recently been asked to administer a couple ubuntu boxes running web servers. I'm a dev by trade so if this question is fairly noob please forgive. We have about a dozen sites running on this box. 2 of our sites need to talk back and forth over a restful api. Unfortunately we are having issues with the sited connection to each other via wget. When we try and run wget manually from the command line from the server pointing to a site also on that server it hangs and eventually times out. If we do the same thing from outside the server to the same site on the server it works. Is there something that could be preventing sites on the same server from communicating with each other? The same thing happens pinging the site from the server.

  Read the article

• Unattended Install of Zend Server license

  - by Zoop - Josh

  I have a Zend Server 5.6 development license and I wanted to know if there is a way to apply the license during install, rather than via the web interface after it has installed. I ask because I administer our server environment via Rightscale and have automated the creation of the server, however it still requires manual input for the license details. We regularly fire up a staging server to do final tests before pushing to production and it would be great if it were completely hands off.

  Read the article

• NDR for meeting requests

  - by Adam

  We've got a mailbox for each department (e.g [email protected] and [email protected]) and everyone in that department has access to it, access is granted using Exchange Management Console. If I send a calendar invite to [email protected], I get a Undeliverable report: Delivery has failed to these recipients or groups: User_A The e-mail address you entered couldn't be found. Check the address and try resending the message. If the problem continues, please contact your helpdesk. User_B The e-mail address you entered couldn't be found. Check the address and try resending the message. If the problem continues, please contact your helpdesk. User_C The e-mail address you entered couldn't be found. Check the address and try resending the message. If the problem continues, please contact your helpdesk. The users are no longer in AD or Exchange but we cannot find any mention of them within any deligates or permissions anywhere. We only started to get this problem AFTER we upgraded our DCs from Windows Server 2003 to Windows Server 2008 and Exchange server from Windows Server 2003, with Exchange 2005 to Windows Server 2008, with exchange 2010.

  Read the article

• In-Place DC Upgrade from Server 2003R2 Standard to 2008 Enterprise

  - by Yadhu Tony

  We have a Domain controller in server 2008 Enterprise and Additional DC in server 2003 R2. Now I need to upgrade Additional Domain controller to Server 2008 Enterprise and raise the domain functional level to 2008. The DC is running with Active Directory, DNS and DHCP. The server is installed in VMware ESXi 4.0. Please guide me to carry out the upgrade. Also I want to know about the possible risk of in-place upgrade, if any.

  Read the article

< Previous Page | 140 141 142 143 144 145 146 147 148 149 150 151  | Next Page >