Search Results

Search found 27979 results on 1120 pages for 'network drive'.

Page 145/1120 | < Previous Page | 141 142 143 144 145 146 147 148 149 150 151 152  | Next Page >

  • mdadm: Replacing array with entirely new drives

    - by hellfur
    I have a server with three 500GB drives, with most of my data in a RAID5 configuration spanning the three of them. I just purchased and installed four 1TB drives, and the intention is to move off of the old drives and onto the new ones. I have enough SATA ports and power connectors to power all seven of my drives at once, so I've kept the old RAID running while I figure out what to do with the new drives. My question is: Should I create a whole new array on the 1TB drives, then move everything over and reconfigure linux to boot from the new md arrays? Or should I just expand the array, swapping out each of the three 500GBs with the 1TB, then adding the final drive? I've read up on the mdadm extending drive setup, and it makes sense, but I imagine I would use one of the drives as a full backup while I move things over, then add that drive back into the array once things are up and running on three of the 1TB drives, so there's some complication in going that route as well... I'm just not sure which is safer/recommended.

    Read the article

  • Corsair SSD appears completely blank and does not retain written data

    - by ebanders
    I have a 180GB Corsair SSD (model# CSSD-F180GB2-BRKT) as the primary drive in a Windows laptop. Recently the machine became unbootable after installing Windows updates. Windows installed updates before the machine shut down and the next time the machine boot up it complained about not being able to find a bootable device. After finding fixmbr unsuccessful at making the machine unbootable, I investigated a little within knoppix. Fdisk revealed an empty partition table. A scan by Testdisk came up empty. And finally 'head -c 1024 | hd' reveals all zeros. Creating a primary partition spanning the whole disk completes successfully, but after a reboot the disk appears empty again. dmesg reveals no read or write errors. smartctl indicates that the drive is healthy- although the SMART attribute values do not appear to be read properly. "Data Page | WARNING: PREVIOUS ATTRIBUTE HAS TWO" and "Threshold Page | INCONSISTENT IDENTITIES IN THE DATA" messages appear within the table of values. I don't have much experience with SSDs. Is this drive dead or something? Can anyone recommend any diagnostic tools that may be suited for diagnosing SSDs?

    Read the article

  • No network connectivity (not wired or wireless) - RT5390

    - by Ben Udy
    I am starting to think I simply need to accept a small loss and sell my new ASUS K73E. Because I really don't enjoy computing when I have to deal with Windough$ and this windows 7 64 bit on my new ASUS is even worse than the old machines with XP. I have written to ASUS and they simply say "We don't support Linux" and while Ralink's website says they do support Linux I can't get anyone to tell me what model Ralink card might be in my machine. Is anyone out there who might be able to give me some useful advice???? Here is the answer to command lspci nn && lsusb && lsmod && rfkill list all: di,snd_seq snd 54244 16 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device uvcvideo 57374 0 videodev 34361 1 uvcvideo v4l1_compat 13251 2 uvcvideo,videodev soundcore 6620 1 snd snd_page_alloc 7076 2 snd_hda_intel,snd_pcm psmouse 63677 0 serio_raw 3978 0 lp 7028 0 parport 32635 2 ppdev,lp fbcon 35102 71 tileblit 1999 1 fbcon font 7557 1 fbcon bitblit 4707 1 fbcon softcursor 1189 1 bitblit video 17375 0 output 1871 1 video vga16fb 11385 1 vgastate 8961 1 vga16fb ahci 32360 2 di,snd_seq snd 54244 16 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device uvcvideo 57374 0 videodev 34361 1 uvcvideo v4l1_compat 13251 2 uvcvideo,videodev soundcore 6620 1 snd snd_page_alloc 7076 2 snd_hda_intel,snd_pcm psmouse 63677 0 serio_raw 3978 0 lp 7028 0 parport 32635 2 ppdev,lp fbcon 35102 71 tileblit 1999 1 fbcon font 7557 1 fbcon bitblit 4707 1 fbcon softcursor 1189 1 bitblit video 17375 0 output 1871 1 video vga16fb 11385 1 vgastate 8961 1 vga16fb ahci 32360 2 Edit #2 lspci 00:00.0 Host bridge: Intel Corporation Device 0104 (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Device 0116 (rev 09) 00:16.0 Communication controller: Intel Corporation Cougar Point HECI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation Cougar Point High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 2 (rev b5) 00:1c.5 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 6 (rev b5) 00:1d.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation Device 1c49 (rev 05) 00:1f.2 SATA controller: Intel Corporation Cougar Point 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation Cougar Point SMBus Controller (rev 05) 02:00.0 Network controller: RaLink Device 5390 03:00.0 Ethernet controller: Atheros Communications Device 1083 (rev c0) lsusb Bus 002 Device 002: ID 8087:0024 Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 13d3:5710 IMC Networks Bus 001 Device 002: ID 8087:0024 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Thanks for the suggestion because this gave me a model for Ralink RT5390. I have now gone to Ralink.com and downloaded (via Windows 7) the driver package (it is a bz2 file). I hope I can figure out how to install it. And FYI - I was not able to run su (not authorized?) and dmidecode didn't exist (probably needs to be downloaded BUT no internet yet in Ubuntu)

    Read the article

  • How do I restore a non-system hard drive using Time Machine under OSX?

    - by richardtallent
    I dropped one of the external drives on my Mac Pro and it started making noises... so I bought a replacement drive. No biggie, that's why I have Time Machine, right? So now that I have the new drive up and initialized, how do I actually restore the drive from backup? Time Machine is intuitive when it comes to restoring the system drive or restoring individual folders/files on the same literal device, but I'm a bit stuck in how to properly restore an entire drive that is not the boot drive. I saw one suggestion to use the same volume name as the old drive and then go into Time Machine. Haven't tried that since the information is unconfirmed. For now, I just went to the Time Machine volume, found the latest backup folder for that volume, and I'm copying the files via Finder. Of couse, I expect this to work just fine, but I feel like I'm missing something if that's the "proper" way to do this.

    Read the article

  • Network attached external harddrive from another computer.

    - by Paul Knopf
    I have a server that is setup in raid. It is on the same network as my main computer. I would like to have some of the memory on my server to act as a network attached drive on my main computer. Basically, I want it to be a new data drive (similar two C:\, but 2nd drives are mostly E:). That way, I can reformat my main computer without loosing any important data. And the data that is saved (on server E:\ drive) is secured via raid mirroring.

    Read the article

  • How to Recover HDD Formatted by "Create a Recovery Drive" Tool of Windows 8.1?

    - by ide
    I have 2 TB USB HDD which had these drives F: about 1 TB with 750 GB data H: about 120 GB with 60 GB data I: about 780 GB with 250 GB data (For TV: It was raw in Windows but visible in the Smart TV) I took 521 MB from last part of H to get new G drive. Then I run "Create a Recovery Drive" tool of Windows 8.1 and chose G drive. It said all data in the drive will be deleted. I thought it is just G drive but it deleted my whole HDD. It created 32 GB new F drive with writing 337 MB on it and rest of HDD is unallocated. I tried these programs to get my first 3 drives but non of them helped for getting 1st partition. TestDisk MiniTool Partition Wizard Home Edition EaseUS Partition Master 9.2.2 (I deleted new F drive volume because it scans only unallocated part) Recuva PC Inspector File Recovery

    Read the article

  • How many hours of use before I need to clean a tape drive?

    - by codeape
    I do backups to a HP Ultrium 2 tape drive (HP StorageWorks Ultrium 448). The drive has a 'Clean' LED that supposedly will light up or blink when the drive needs to be cleaned. The drive has been in use since october 2005, and still the 'Clean' light has never been lit. The drive statistics are: Total hours in use: 1603 Total bytes written: 19.7 TB Total bytes read: 19.3 TB My question is: How many hours of use can I expect before I need to clean the drive? Edit: I have not encountered any errors using the drive. I do restore tests every two months, and every backup is verified. Edit 2: The user manual says: "HP StorageWorks Ultrium tape drives do not require regular cleaning. An Ultrium universal cleaning cartridge should only be used when the orange Clean LED is flashing." Update: It is now May 2010 (4.5 years of use), and the LED is still off, I have not cleaned, backups verify and regular restore tests are done.

    Read the article

  • Network backup for Macs and PCs - formatting question

    - by neilfein
    I'm trying to use a LaCie 2TB drive as an AirPort drive, for backup on a home network. We have one mac and two PC laptops. My plan is to create a Mac partition and a Windows partition. However, Disk Utility won't let me set the windows partition to Windows format; there's no option in the menu for it in the partition tab. Am I doing something wrong? Alternatively, is there a way to partition the drive with one partition that all three machines can see? We have a Mac G5 with 10.4 and two laptops with Windows 7. Thanks!

    Read the article

  • Adaptec 2020SA RAID controller Set up in RAID5, one drive went down, can I still get data?

    - by SJaguar13
    I have 6 1tb drives in a RAID5. 1 drive went down. On the RAID was 2 virtual machines that I really need back up and running. The spare drive I have to put in the server is a 1.5tb drive, which exceeds the physical per drive limit of the 2020SA. The drive is found in the disk utility, but it is not found in the array management section. I cannot add the drive to the array to have it rebuild. I have a replacement drive along with some spares on their way from Newegg, but I am still looking at a few days of downtime. Is it possible to use the 5 working drives to get the VMs copied off and on to another server or do I just have to wait for the drives to get here?

    Read the article

  • Why do we still have to use drive letters to identify file systems?

    - by Charles E. Grant
    A friend has run into a problem where they installed Windows 7 from an external drive, and the internal boot drive is now assigned to H:. Theoretically this shouldn't cause problems because there are programming interfaces for getting the drive letter for the system drive. In practice though, there are quite a few programs that assume that C: is the only possible location for the system directories, and they refuse to run with the system directories on H:. That's not Microsoft's fault, but it's a pain none-the-less. The general consensus seems to be that a re-install, setting the internal boot drive to C:, is the only way to avoid fix these problems. UNIX-like systems display all file systems in a single unified directory tree and mostly seem to avoid problems like this. Is it possible to configure a Windows system without reference to drive letters, or does the importance of backwards compatibility mean that Windows will be working with drive letters from now until doomsday?

    Read the article

  • How can I prevent JungleDisk/MacOS X (10.6) creating a local volume for a removed external drive?

    - by Rew
    Ok, here is situation: I use JungleDisk to sync an online folder on to a external drive connected to my Mac. If I right click Finder, click Go to Folder... then type /Volumes/ I see the drive linked here. Once I remove the external drive, an actual folder is created here in the name of the external drive, JungleDisk continues to copy files to this folder, rather than stop. Is this a feature of Mac OS X? Can I turn if off? After I re-connect my external drive, the link to the drive is appended with a 1 (so if I called the drive SpareDrive it becomes SpareDrive 1 as the newly created folder is called SpareDrive. I realise my explanation isn't very clear, but anyone understand this, and knows how to prevent it happening please let me know. PS: I have a low reputation as I don't use this often, I tend to use stackoverflow, but will check back here for answers.

    Read the article

  • How many hours of use before I need to clean a tape drive?

    - by codeape
    I do backups to a HP Ultrium 2 tape drive (HP StorageWorks Ultrium 448). The drive has a 'Clean' LED that supposedly will light up or blink when the drive needs to be cleaned. The drive has been in use since october 2005, and still the 'Clean' light has never been lit. The drive statistics are: Total hours in use: 1603 Total bytes written: 19.7 TB Total bytes read: 19.3 TB My question is: How many hours of use can I expect before I need to clean the drive? Edit: I have not encountered any errors using the drive. I do restore tests every two months, and every backup is verified. Edit 2: The user manual says: "HP StorageWorks Ultrium tape drives do not require regular cleaning. An Ultrium universal cleaning cartridge should only be used when the orange Clean LED is flashing." Update: It is now May 2010 (4.5 years of use), and the LED is still off, I have not cleaned, backups verify and regular restore tests are done.

    Read the article

  • Sharing a Win7 Mappable Network Drive in Server 2008 R2

    - by Jason
    I have a ghetto windows server 2008 r2 server that I basically run as a file server. I would like to create a share that can be mapped as a network drive by a Windows 7 Pro PC. How can I do this? I've gathered that I probably need to setup a VPN network on my Server 2008 R2 box and then grant my Win7 PC access. Is there anything else I am overlooking or is there a better way to do this? I basically just want to be able to edit xml files on my Win7 PC without having to ftp them back and forth.

    Read the article

  • Social Network Updates: While You Were Busy Marketing 2

    - by Mike Stiles
    Since social moves at the speed of data, it’s already time for another update, as we did back in April, on the changes the various social networks have made or gone through while you were busy marketing. Facebook There’s a lot of talk Facebook’s developing a mobile product to act like Flipboard and surface news, from both users and media outlets. The biggest news was Facebook/Instagram’s introduction of 15-second videos, enhanced with with filters, to take some of Vine’s candy. You can also delete parts of videos and rerecord them, and there’s image stabilization. Facebook’s ad revenue is coming along just fine, thank you very much. 35% quarter-to-quarter growth in Q2. And it looks like new formats like Mobile App Install Ads and Unpublished Page Posts are adding to the mix. If you don’t already, you’ll soon see a little camera in comment boxes letting you insert photos right into the comments you make. The drive toward “more visual” continues. The other big news is Facebook’s adoption of our Twitter friend, the hashtag. Adding # sets apart the post topic so it can be easily found or discovered. It’s also being added to Google Plus, Tumblr, and Pinterest. Twitter Want to send someone a promoted tweet when they’re in range of your store? That could be happening by the end of this year. Some users have been seeing automatic in-stream previews of images on Twitter.com. Right now it’s images in your own tweets, but we can assume all tweets are next. Get your followers organized! Twitter raised the limit on the number of lists you can create from 20 to 1,000. They also raised the number of accounts you can have in a list from 500 to 5,000. Twitter started notifying you when someone favorites a tweet you’re mentioned in or re-tweets a tweet you re-tweeted. Anyway, it’s the first time Twitter’s notified you about indirect interactions like that. Who’s afraid of Instagram? A study shows 6-second Vine videos are being posted to Twitter at the rate of 9/second, up from 5/second 2 months ago. Vine has over 13 million users and branded Vines are 4x more likely to be shared than video ads. Google Plus Now featuring a 3-column redesigned stream, and images that take up a whole column. And photo filters Auto Highlight and Auto Awesome work to turn your photos into a real show. Google Hangouts is the workhorse for all Google messaging now, it’s not just an online chat with 9 people anymore. Google Plus Dashboard improves the connection between your company’s Google Plus business page and your Google Plus Local. Updates go out across all Google properties and you can do your managing from the dashboard. With Google Plus’ authorship system, you can build “Author Rank” based on what you write and put on the web. If your stuff is +1’ed and shared a lot, you’re the real deal and there are search result benefits. LinkedIn "Who's Viewed Your Updates" shows you what you’ve shared recently, who saw it and what they did about it in real-time. “Influencers” is, well, influential. Traffic to all LI news products has gone up 8x since it was introduced. LinkedIn is quickly figuring out how to get users to stick around awhile. You and your brand can post images and documents in status updates now. In fact, that whole “document posting” thing is making some analysts wonder if LinkedIn will drift on over to the Dropboxes and YouSendIts of the world. C’mon, admit it. Your favorite part of LinkedIn is being able to see who’s viewed your profile. Now you’ve got even more info and can see what/who you have in common. Premium users get even deeper insights about how people are finding them. If you’re a big fan of security, you’ll love that LinkedIn started offering two-factor authentication (2FA). It’s optional, but step 2 is a one-time code texted to your registered mobile. Pinterest A study showed pins have a looong shelf life compared to other social net posts. “Clicks kept coming for 30 days and beyond.” Most pins are timeless, and the infinite scroll causes people to see older pins. Is it a keeper? Pinterest jumped 82% to 54 million users in the past year. It’s valued at $2.5 billion and is one of the biggest sources of referral traffic there is. That said, CEO Ben Silbermann adds, "Right now, we don't make money." A new search feature stops you from having to endlessly scroll through your own pins looking for that waterfall picture you posted. Simply select “just my pins” in the search bar. New "Rich Pins" lets brands add info like price and availability to pins that can be updated daily via a data feed from your merchant site. Not so fast, you have to apply to Pinterest for it first. Like other social nets, Pinterest does not allow sexual content, nudity, or even partial nudity. However…some art contains nudity, and Pinterest wants to allow art. What constitutes “art” will be judged by…what we have to assume are Pinterest employees who love their job. @mikestilesPhoto: stock.xchng, Tim Marmon

    Read the article

  • Using pfSense, OpenVPN Connects but Still Can't See the Network

    - by nicorellius
    I am having an OpenVPN issue. I have a pfSense box at home configured to allow traffic through a VPN tunnel. The client computer is Windows XP Home, behind a standard Comcast connection and a Netgear wireless router. I use OpenVPN to access my work network (from where I am trying to get out of in this post) from home (with an XP Pro machine behind pfSense), and this works fine. The client config is similar but has the changes specific to my setup... Here is my XP Home config: client dev tun proto tcp remote pfsense.*.org 1194 (starred out by me) resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert client.crt key client.key ns-cert-type server comp-lzo verb 3 When I launch the OpenVPN GUI, the Tunnel TAP network connection turns red, and I can right-click that to connect to the server. Everything seems to work fine until I browse for the actual network. The Tunnel TAP connection turns green and it says connected to 10.1.1.6 (I have tried different IP pools here too with no luck). I can see the internal network fine, but my home network behind pfSense is not there. I have tried browsing there by using Tools Map Network Drive, using the browser, with no success. When I open the command line on the client and use the ipconfig -all command, I get the following: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : TAP-Win32 Adapter V9 Physical Address. . . . . . . . . : *** (starred out by me) Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 10.1.1.6 Subnet Mask . . . . . . . . . . . : 255.255.255.252 Default Gateway . . . . . . . . . : DHCP Server . . . . . . . . . . . : 10.1.1.5 Lease Obtained. . . . . . . . . . : Monday, March 15, 2010 1:18:37 PM Lease Expires . . . . . . . . . . : Tuesday, March 15, 2011 1:18:37 PM I noticed that the default gateway is not present. Could this be my problem? I am still relatively new to firewalls, VPN, and network configuration so I'm sure I am messing up something simple. Oh yah, I should note that I have firewall rules configured for pfSense to allow traffic through the WAN and the LAN. At first there was just the WAN firewall rule, because that is what I got from the literature I was reading. I then created a LAN rule as well, but I'm not sure if this was correct. Neither way works, though. Screen shots below: Any help is much appreciated.

    Read the article

  • Drive XML returning Windows Volume Shadow Service Error

    - by Ssvarc
    I'm trying to image a SATA laptop hard drive, using DriveImageXML, that is attached to my computer via a USB adapter. I'm running Win7 Ultimate 64 bit. DriveXML is returning: Could not initialize Windows Volume Shadow Service (VSS). ERROR C:\Program Files (x86)\Runtime Software\Drivelmage XML\vss64.exe failed to start. ERROR TIMEOUT Make sure VSSVC.EXE is running in your task manager. Click Help for more information. VSSVC.EXE is running in Task Manager, as is VSS64.exe. Looking at the FAQ on the Runtime webpage this turned up: Please verify in Settings-Control Panel-Administrative Tools-Services that the following services are enabled: MS Software Shadow Copy Provider Volume Shadow Copy Also make sure you are able to stop and start these services. Possible reasons for VSS failures: For VSS to work, at least one volume in your computer must be NTFS. If you use only FAT drives, VSS will not function. The required NTFS volume does not need to be identical with the volume you want to image. You should make sure that VSSVC.EXE is running in your task manager. If the problems persist, registering "oleaut.dll" and "oleaut32.dll" using "regsvr32" might help. Both of those services are running and can be started and stopped without issue. Using "regsvr32" to register ""oleaut32.dll" returns successful, but "oleaut.dll" returns: The module "oleaut.dll" failed to load. Make sure the binary is stored at the specified path or debug it to check for problems with the binary or dependent .DLL files. The specified module could not be found. Some other information that might be relevant. Browsing to the drive is successful, but accessing certain folders returns an "access" error. Windows runs a permissions adder that adds the current user profile to the NFTS permissions. Could this be the cause of the issue? DriveImage XML is running as Administrator. Thoughts?

    Read the article

  • trying to get the most accurate device location from GPS or Network in Android

    - by arc
    I am trying to determine the most accurate location of a device, in the shortest time possible. I am storing the data as a geopoint, and have it displayed on a mapview. The last time I activated the GPS on my device and let it get a location lock, i was approx 80 miles from where I am now. I have a location manager setup and a location listener. If I do this, I get NULL. myLocOverlay = new MyLocationOverlay(this, mapView); GeoPoint test = myLocOverlay.getMyLocation(); but in the next couple of lines; myLocOverlay.enableMyLocation(); mapView.getOverlays().add(myLocOverlay); With this, the overlay on the map shows the current location. It is using the Network provider, but is also attempting to get a GPS fix (it can't as I am indoors and no where near the top floor). If I construct the geopoint like this; if(lm.getLastKnownLocation("gps") != null) { test = new GeoPoint( (int) (lm.getLastKnownLocation("gps").getLatitude() * 1E6), (int) (lm.getLastKnownLocation("gps").getLongitude() * 1E6)); } else { if(lm.getLastKnownLocation("network") != null) { test = new GeoPoint( (int) (lm.getLastKnownLocation("network").getLatitude() * 1E6), (int) (lm.getLastKnownLocation("network").getLongitude() * 1E6)); } //bad things } Then I get confusing results. If I disable the devices GPS provider then the code moves onto the Network Provider and gives me a fairly accurate result. If I enable the GPS provider, then the geopoint comes back as the last place I allowed the device to get a GPS lock. I want to avoid the above results, and so was looking at using; GeoPoint test = myLocOverlay.getMyLocation(); BUT as I said above, I just get NULL from that. Short of getting the geopoints from both GPS and Network and then comparing them, and disregarding the GPS result if it is say 1 mile out of the Network location - i'm a bit stuck. why doesn't getMyLocation() work, shouldnt that return the GeoPoint of what myLocOverlay is showing on the mapview?

    Read the article

  • why does Integrated Windows Authentication fail when clients access off the network

    - by Bryan
    My background is not with web applications so this problem is hard for me to explain easily. First I'll try to describe the setup. Client setup:-Only browser that is effected is IE 6-8 (Firefox, chrome, opera, and safari all work fine) -A user will try to access our web application from a company laptop that is not connected to our network. -This machine will be a member of our workgroup and have the company DNS listed as a trusted intranet site. (to which the application in question would be a member) -The security logon mode is set to Automatic Logon only in intranet zone only, and IWA authentication is enabled on the clients browser.Server setup:-Windows server 2003 fp2-The application will first redirect to an Authorization asp page which has anonymous access disabled and IWA enabled in IIS.what should happen is that, since the client is not currently on the network, when this page is called it should prompt the user for network credentials. But with IE, instead of prompting, the user gets a page cannot be displayed error because the IIS manager is denying access to the asp page. If the company DNS is removed from the trusted intranet site list then it prompts correctly but disables single sign on the next time that computer is connected to the network or vpn. My assumption is that since IE uses IWA and the site is listed as an internal site, when no network is found IE just sends nulls to the server attempting to authenticate which is swiftly punted back. Other browsers do not have security zones so when network credentials are not present the server prompts for them. Is there a way to get around this so that our clients can keep the company DNS in the intranet zone but still have the server prompt for credentials when not on the network? Any attempt to allow for anonymous access on the asp page, as far as I know, will cause AUTH_USER to return null and again break SSO. I realize this is slightly rambling so I will do my best to clarify and questions you guys might have. Thanks in advance.

    Read the article

  • Internet Explorer / Windows 7 does not want to show HTML file from local network drive

    - by Jaanus
    Setup: I have Windows 7 running inside VirtualBox on Mac OS X host. I have a shared drive with some HTML files, that I am mounting as a local drive W: in Windows, from the VirtualBox server \VBOXSVR. I want to look at them with a browser in Windows. Chrome in Windows 7 opens and shows those HTML files just fine (file:///W:/welcome.html). But Internet Explorer does not, and shows this error instead of the files: Internet Explorer cannot display the web page What you can try: [button Diagnose Connection Problems] More information This problem can be caused by a variety of issues, including: Internet connectivity has been lost. The website is temporarily unavailable. The Domain Name Server (DNS) is not reachable. The Domain Name Server (DNS) does not have a listing for the website's domain. If this is an HTTPS (secure) address, click Tools, click Internet Options, click Advanced, and check to be sure the SSL and TLS protocols are enabled under the security section. For the internet zone in the status bar, it shows: Internet | Protected Mode: On IE settings are a mystery to me, and I could possibly get it to work by tweaking IE settings, but I don't know which ones. How do I make IE show the same files that Chrome is happy to show? (Chrome showing them means that the files themselves are fine, there is something about the setup that just makes IE be a diva.)

    Read the article

  • Erase just the free space on my hard drive

    - by Patriot
    I'm about to give away an older computer with just the Windows XP operating system intact and all other programs uninstalled. However, upon peeking at the "free space" with software called "Recuva", I notice lots of deleted things that could be recoverable. Some of these include sensitive data files, pdfs, and other personal items that I would not want retrieved. I ran a program called "Eraser" to try and overwrite that data, but it failed to do an adequate job. I also tried to do the job with "Glary Utilities" but it failed too. Short of installing a new, very cheap hard drive and re-installing the bare bones operating system, I'm out of ideas. EDIT - WOW!!! I was not really expecting this many GREAT ideas. My next question is this. If I go the DBAN route and truely wipe the hard drive, then restore my disc image (I use Acronis True Image) will it also restore the free space data? Does imaging just copy readable data? I have an old image of when the OS was first installed.

    Read the article

  • Making sense of S.M.A.R.T

    - by James
    First of all, I think everyone knows that hard drives fail a lot more than the manufacturers would like to admit. Google did a study that indicates that certain raw data attributes that the S.M.A.R.T status of hard drives reports can have a strong correlation with the future failure of the drive. We find, for example, that after their first scan error, drives are 39 times more likely to fail within 60 days than drives with no such errors. First errors in re- allocations, offline reallocations, and probational counts are also strongly correlated to higher failure probabil- ities. Despite those strong correlations, we find that failure prediction models based on SMART parameters alone are likely to be severely limited in their prediction accuracy, given that a large fraction of our failed drives have shown no SMART error signals whatsoever. Seagate seems like it is trying to obscure this information about their drives by claiming that only their software can accurately determine the accurate status of their drive and by the way their software will not tell you the raw data values for the S.M.A.R.T attributes. Western digital has made no such claim to my knowledge but their status reporting tool does not appear to report raw data values either. I've been using HDtune and smartctl from smartmontools in order to gather the raw data values for each attribute. I've found that indeed... I am comparing apples to oranges when it comes to certain attributes. I've found for example that most Seagate drives will report that they have many millions of read errors while western digital 99% of the time shows 0 for read errors. I've also found that Seagate will report many millions of seek errors while Western Digital always seems to report 0. Now for my question. How do I normalize this data? Is Seagate producing millions of errors while Western digital is producing none? Wikipedia's article on S.M.A.R.T status says that manufacturers have different ways of reporting this data. Here is my hypothesis: I think I found a way to normalize (is that the right term?) the data. Seagate drives have an additional attribute that Western Digital drives do not have (Hardware ECC Recovered). When you subtract the Read error count from the ECC Recovered count, you'll probably end up with 0. This seems to be equivalent to Western Digitals reported "Read Error" count. This means that Western Digital only reports read errors that it cannot correct while Seagate counts up all read errors and tells you how many of those it was able to fix. I had a Seagate drive where the ECC Recovered count was less than the Read error count and I noticed that many of my files were becoming corrupt. This is how I came up with my hypothesis. The millions of seek errors that Seagate produces are still a mystery to me. Please confirm or correct my hypothesis if you have additional information. Here is the smart status of my western digital drive just so you can see what I'm talking about: james@ubuntu:~$ sudo smartctl -a /dev/sda smartctl version 5.38 [x86_64-unknown-linux-gnu] Copyright (C) 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: WDC WD1001FALS-00E3A0 Serial Number: WD-WCATR0258512 Firmware Version: 05.01D05 User Capacity: 1,000,204,886,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Thu Jun 10 19:52:28 2010 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 179 175 021 Pre-fail Always - 4033 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 270 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 1468 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 262 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 46 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 223 194 Temperature_Celsius 0x0022 105 102 000 Old_age Always - 42 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0

    Read the article

  • New XPC: No video, no ethernet link, but drive spins

    - by Mike Pennington
    I bought a Shuttle XPC SH67H3 with integrated video. I installed: An Intel i5 2450P 16GB DDR3 RAM A SATA hard drive from my old linux server that still is bootable I have both power connectors plugged into the motherboard. I realize that the Intel i5-2450P doesn't have video capabilities; however, the drive spins like it's doing something useful. It seems like I should get an ethernet link light when I fire this up. I plan to run this headless anyway, so it would be really nice if I could figure out how to run this without a video card at all. I know the IP address and login info for the linux install on the disk. I plugged in speakers, but get no bios beeps when I power it up. Shuttle's bios manual has nothing in there that indicates I should have problems in this configuration. My questions: Is there a reason that the missing video card would block usage of the ethernet port? Are there settings on the motherboard / bios I can change to get this working?

    Read the article

  • Unable to connect to shared (iscsitarget) dvd-rw drive on ubuntu karmic box

    - by develop7
    Preface: I have desktop with DVD-RW drive that runs primarily on Linux (namely Ubuntu 9.10). My wife has netbook that rins Windows XP with no cd/dvd drive. There's also LAN through our ADSL modem/router. I've "ported" (actually, I've just grabbed sources and ran dpkg-buildpackage) iscsitarget package from Ubuntu Lucid to Karmic (here are packages), installed it (sudo aptitude install iscsitarget; sudo m-a a-i iscsitarget) and configured it in the following way (/etc/ietd.conf): Target iqn.2020-01.local.develop7-desktop:storage.disc.dvdrw Lun 0 Path=/dev/sr0,Type=blockio #I've skipped commented lines Also, I've opened port 3260 with ufw: $ sudo ufw status | grep 3260 3260 ALLOW 192.168.1.0/24 But (here's the trouble) I still can't connect to this target from Windows box. Microsoft Software iSCSI Initiator tells "Logon failure" upon connect attempt. After unsuccessful connection attempt I've noticed this line in dmesg | tail's output: iscsi_trgt: ioctl(299) invalid ioctl cmd c078690d So the question is — what's wrong with my config/iSCSI target/whatever else? Or, in short — what I'm doing wrong? Thanks in advance.

    Read the article

  • Unable to connect to shared (iscsitarget) dvd-rw drive on ubuntu karmic box

    - by Develop7
    Intro I have desktop with DVD-RW drive that runs primarily on Linux (namely Ubuntu 9.10). My wife has netbook that rins Windows XP with no cd/dvd drive. There's also LAN through our ADSL modem/router. I've "ported" (actually, I've just grabbed sources and ran dpkg-buildpackage) iscsitarget package from Ubuntu Lucid to Karmic (here are packages), installed it (sudo aptitude install iscsitarget; sudo m-a a-i iscsitarget) and configured it in the following way (/etc/ietd.conf): Target iqn.2020-01.local.develop7-desktop:storage.disc.dvdrw Lun 0 Path=/dev/sr0,Type=blockio #I've skipped commented lines Also, I've opened port 3260 with ufw: $ sudo ufw status | grep 3260 3260 ALLOW 192.168.1.0/24 Problem But (here's the trouble) I still can't connect to this target from Windows box. Microsoft Software iSCSI Initiator screams "Logon failure" upon connect attempt, and, respectively, fails to connect. After unsuccessful connection attempt I've noticed this line in dmesg | tail's output: iscsi_trgt: ioctl(299) invalid ioctl cmd c078690d Question So the question is — what's wrong with my config/iSCSI target/whatever else? Or, in short — what I'm doing wrong? Thanks in advance.

    Read the article

  • How to make a huge ram drive?

    - by Brandon Moore
    At my old job when a report was needed I could sit down with someone and pull up results and get immediate feedback, and then refine my queries and ultimately have the data we needed, in the format we needed within 30-90 minutes. I just started working for a new company with a database containing millions of records and I spent my whole 8 hours making a report that I feel I could have made in less than 2 hours if it were not for the massive amount of data the queries are working with, and the fact that I couldn't ask the person needing the data to sit down with me and give me feedback as I pulled up results as I am used to. So I am trying to think of how we can make the server faster... much faster, so that I can have the same level of productivity I'm used to. One thought that just came to mind is that memory is so cheap these days, and by my calculations I could buy 10 8gig ram sticks for 1000 bucks. What I have never heard of though is a device that would let me combine these into a huge ram drive. So I'd like to know if any such device exists, and if not what is the largest ram drive I could realistically make and how would I go about doing so? EDIT: To you guys who are saying the database shema needs to be analyzed... you can't make a query such as "Select f1, f2, f3, etc from SomeTable" run any faster by normalizing or indexing the table. What I'm talking about IS ABSOLUTELY a need for improved performance at the hardware level. I am used to having results come back to me in a few seconds, not a few minutes or much less a half an hour. Maybe that's what you guys are used to who have 100 billion record tables and you feel like that's fast, but I'm looking for results back from tables with about 10 million records to come back to me withing less than half a minute TOPS.

    Read the article

< Previous Page | 141 142 143 144 145 146 147 148 149 150 151 152  | Next Page >