Search Results

Search found 8185 results on 328 pages for 'capture card'.

Page 147/328 | < Previous Page | 143 144 145 146 147 148 149 150 151 152 153 154  | Next Page >

• Expresscard Not Detected in PCI-E Adapter

  - by maxpower47

  I'm trying to put an expresscard TV tuner (Avermedia HC82) into my HTPC using this expresscard to PCI-E adapter. I've verified that the tuner works fine in my laptop. The motherboard is a Biostar TF7050-M2. When I install it and turn it on, the light on the back of the adapter comes on fine (there are two indicator lights on the back to show if it is using PCI-E or USB communication, USB communication goes through a USB cable connected between the card and a header on the motherboard) showing that it is working in PCI-E mode. However, the device is never detected in Windows 7 Professional x64. The auto detect never happens, it doesn't show up in the device manager, and I can have it rescan for new hardware and nothing is found. I tested the whole setup (tuner + adapter) in another PC (also using Win 7 Pro x64) and it worked fine. I also tried: Plugging the adapter in to the PCI-E x16 slot on the motherboard (I verified first that the x16 slot worked by installing a video card in it) Booting into safe mode and rescanning Updating the chipset drivers Installing the tuner drivers first Using a different USB cable, plugged in to one of the known good ports on the back of the board Trying it without the USB cable plugged in Removing the other PCI cards that were installed on the board Looking through the BIOS for any setting that might be disabling it somehow to no avail. I'm at a loss for what else to try. I really don't want to RMA it (the shipping back to newegg will be almost as much as it cost to buy in the first place. Any ideas?

  Read the article

• Linux Mint Constantly freezing on Dell XPS L502X

  - by Josh

  I recently partitioned my hard drive to dual boot the existing Windows 7 with Linux Mint because I am tired of using Windows, especially the lack of terminal. I want to eventually remove Windows 7 and just run it from a VM within Linux Mint, but I want to make sure that I like the Mint before going all in. I ran Linux Mint on a VM inside Windows for a while, enjoyed it, and never had any issues with it. Since installing on my hard drive it has started freezing every 5-10 minutes, and the only way to get it back is to either power down, or close the lid and reopen once it sleeps. I've also tried running Ubuntu on dual boot in the past, and while it never froze, the battery life was terrible, and the fan was constantly running. I'm experiencing the same battery/fan problem with Mint, which doesn't make sense to me, as Linux should be lighter on the CPU than windows. If I had to guess I'd say it's probably a driver thing, with my video card or fan or something. My battery life in Windows is ~2 hours and its about 40 minutes in Linux. At this point, that is even if my laptop doesn't freeze before then. On a less important note, I also have an intel Centrino 6150 WiMax card that I'd like to be able to use, but that won't register on the Linux system either. I have tried downloading drivers for both of these, but neither have solved my problems. I'm definitely getting frustrated and am getting close to giving up on Linux even though I dread working on a Windows machine.

  Read the article

• Flickering dual screens in Virtual Box Ubuntu 13.10 Guest

  - by alexleonard

  I have Ubuntu 13.10 x64 installed as a guest in VirtualBox (under a Windows 8.1 host) and have the settings for the virtual machine setup to run with a monitor count of 2, 128MB video memory and 3D acceleration enabled. In my guest I have the virtual box additions installed (which allowed me to have two 1920x1080 screens). Here's a screenshot of my VM settings. My laptop is an Asus N550JV which has both Intel's HD Graphics 4600 GPU and Nvidia's GeForce GT 750M. By default though I believe the Intel GFX card is being used to render the VM. When I boot up the VM it loads perfectly on dual screens, however whenever I move the mouse from one screen to the other (I have a Dell S2340L running over a HDMI connection as a second screen) the screen flickers. I've tried a variety of settings changes in both Ubuntu and the VM settings, but cannot seem to stop this screen flicker. I also used the NVidia control panel in Windows to force the dedicated graphics card to always be used but found that the display driver sometimes crashed whilst working in the VM, resulting in my VM session being destroyed, so I figured it's better to stick with the Intel GFX as that appears to be more stable. I also tried without 3D acceleration but that was much worse, and if I ran the VM with a low amount of graphics memory it really struggled. Here's my dmesg output: http://pastebin.com/1LJuYWMj (not sure if this is helpful in this situation). I read some posts suggesting changes to /etc/X11/xorg.conf but I don't appear to have an xorg.conf file. There were also a few posts (though related to Synergy) suggesting running xset -dpms but this command doesn't appear to have had any effect for me. As an additional note, I'm finding that window drawing in the guest is a little laggy/glitchy. For example, quickly scrolling through a web page may result in parts of the viewport displaying original content. Certainly I notice drawing issues most in the web browser, but it also impacts other software with parts of the window not being drawn when, say, switching between accounts in thunderbird. Any suggestions greatly appreciated!

  Read the article

• DVI splitter not working as expected/confusion between DVI-D and -I

  - by Freakishly

  Hey guys, thanks for looking. I have an ATI FirePro™ V3700 in my desktop machine, and I have been running a dual-monitor setup quite effortlessly, thanks to the two DVI ports on the card. I came upon a third monitor, and wanted to extend my desktop to 3 screens, so I purchased a DVI splitter from Amazon. Now, I can only duplicate the second monitor onto the third, not extend it. I've tried all possible combinations of input to no avail. Here's the setup: The ATI FirePro™ V3700 has two Dual-Link DVI-I outputs The splitter splits a single Dual-Link DVI-I port into two Dual-Link DVI-I outputs Two of the monitors are NEC E222W, and the third monitor is a Dell 2001FP. Each monitor has one D-Sub and one Dual-Link DVI-D input. Cables going from the video card to the monitors are two Dual-Link DVI-D to the NECs and one Single-Link DVI-D to the Dell. Is the problem likely with the DVI-D/DVI-I mismatch? Or is it with the cable on the Dell that is only a Single-Link? The cables are easily replaceable, the monitors not so much. Thanks for your time, I really appreciate it. http://www.amd.com/us/products/workstation/graphics/ati-firepro-3d/v3700/Pages/v3700-specs.aspx http://www.amazon.com/Cables-Unlimited-DVI-D-Splitter-PCM-2260/product-reviews/B000H09RFM/ref=dp_top_cm_cr_acr_txt?ie=UTF8&showViewpoints=1 www dot newegg dot com/Product/Product.aspx?Item=N82E16824002495 accessories dot us dot dell dot com/sna/PopupProductDetail.aspx?cs=19&l=en&c=us&sku=320-1578 Apologies for the fudged links, I'm new here and they won't let me post more than two :P

  Read the article

• How to convert JPEG JFIF files to JPEG Exif format?

  - by tigrou

  I recently put the SD card of my camera in a Windows 7 PC and start browsing pictures on it. I noticed some were not aligned correctly and use rotate feature included in Windows Photo Viewer in order to view them as I wanted. What I didn't know is that when rotate feature is used, it also overwrite the picture when pressing next or previous button resulting in a possible loss of quality (which is in my opinion a bad idea, app should at least warn user of what will happened when using such a feature). After that, I re-inserted the SD card back in my camera and bad surprise happened : the rotated picture could not be previewed anymore. Instead, i got a black screen saying "Incompatible JPEG format". Other files (untouched) are still working ok. To try to understand what happened I opened a JPEG file from camera and one generated on windows 7 in a hex editor. Here is the difference : The camera JPEG files have a Exif tag in them (with 0xE1 in header). Other JPEG files (Windows 7) have first a JFIF tag in it, followed by a Exif tag (with 0xE0 in header). So if i understand it well, both are JPEG files, but using a different internal format. Here is my question : is it possible (using some tool) to convert JFIF files to Exif format ? I understand that original camera files have been reencoded and thus lose some quality (getting originals back is impossible). What i want know if convert them from JFIF back to Exif (without a second loss of quality if possible...)

  Read the article

• Performance decrease in every game and application

  - by Márk Vincze

  When I start a game, initially it runs smoothly, but after a couple of minutes, the performance gradually decreases to the point of being unplayable (1-2 FPS). The sound also starts to lag at this point. This does not happen every time I start my PC, usually exiting the game, rebooting, then starting the game again solves the problem, and I can play with perfect FPS for as long as I want. I could not find any deterministic reason when this happens and when doesn't. It happens in every game I tried (SWTOR, Diablo 3, Skyrim), and not even games, but simple applications like a browser or the Control Panel can get unusably slow. This is a brand new PC I bought three months ago, and this problem occurs since the first day I've been using it. Could you provide any advice how to further diagnose the problem? I tried to reinstall Windows, and tried different video card drivers, but it did not help. It would be important to know whether this is a hardware or software problem, because I can use the warranty if it is a hardware issue. (I did not want to return the PC yet, because I can't reproduce the issue deterministically.) Spec of the pc: Motherboard: ASROCK H61M-HVS CPU: INTEL Core i3-2120 3.30GHz 1155 BOX Memory: KINGMAX 4096MB DDR3 1333MHz KIT Video card: GIGABYTE GV-R685OC-1GD HD6850 1GB GDDR5 PCIE HDD: SEAGATE 500GB Barracuda 7200rpm 16MB SATA3 ST500DM002 I am using Windows 7 64 bit. Thanks a lot in advance!

  Read the article

• realtek lan driver problem - win 7

  - by tango _123

  Hi, my new notebook (ACER TM 8371) with Win 7(x32) professional as OS, has strage behaviour with respect to LAN. when I plug or unplug my charger cable, or my notebook goes in stad-by, or just a do nothing, the netwrok connection is lost. All the energy savings functionbality have been in-activated. if i check the network adapter information, it says "a network cabel is unplugged or corrupted", but it is not true.....the cable is in and it is not corrupted (i tried several which works on other machines). if a tried to di-habilitate and hence re-habilitate, it allows di-habilitation and not to further re-habilitate (it says "no driver for the network card" are available). in some cases, also, the driver disappears (i cannot see it anylonger). if i restart the notebook, everything comes back to normality, but.....today in 3 hours i had to restart 6 times!!! can anyone help me? win 7 says the driver is the last one, so no need to update it. here are some techinical information aboiut network card and driver: Name [00000015] Realtek PCIe GBE Family Controller Adapter type Ethernet 802.3 Product type Realtek PCIe GBE Family Controller Installated YES ID device PNP PCI\VEN_10EC&DEV_8168&SUBSYS_02831025&REV_02\4&266E4C4F&0&00E2 last reset 20/11/2009 11:27 Index 15 Service name RTL8167 I/O Port 0x0000FF00-0x0000FFFF Memory address 0xE2500000-0xE2500FFF Memory address 0xE1400000-0xE140FFFF IRQ Channel IRQ 18 Driver c:\windows\system32\drivers\rt86win7.sys (7.3.522.2009, 164,00 KB (167.936 Byte), 28/08/2009 22:12)

  Read the article

• How to configure network on Windows Server 2008

  - by Gokhan Ozturk

  I have a IBM x3400 Server Machine with Windows Server 2008 R2 installed on it. But, since I am not expert on networking I have some problems. These roles installed on my server: Active Directory DNS File Sharing Hyper-V ISS VPN There is two network card on them. I configured them like this: Local Connection 1: 192.168.30.3 255.255.255.0 192.168.30.2 127.0.0.1 Local Connection 2: 192.168.30.101 255.255.255.0 192.168.30.6 127.0.0.1 My problem is, when I use this Ip gateways, It is sharing internet to all computers. This is not I want. I want to use Local Connection 1 for internal network. I am giving all computers gateway and DNS IP as 192.168.30.3 The Local Connection 2 is for Hyper-V and VPN connections. 192.168.30.2 and 192.168.30.6 are my modem's gateways. I am using 192.168.30.6 external IP for VPN connections. There is two 24 port switches. There is a connection between them and this two ethernet card connected directly to them. And modems are connected to switches as well (Morems are not near the server. They are somewhere in the building). I disabled network Bridge and removed all ethernet cards from it. With this configuration, all computers can ping my server's IP (192.168.30.3) but on server I cannot ping any clients (Request timeout). What is the best way to configure my network? Thank you. Redgards

  Read the article

• Flash Backed Write Cache (FBWC) without capacitor pack

  - by Martyn

  I brought a HP Smart Array P410 controller and it is installed and working fine in a HP Prolient Microserver with 4 drives in two RAID 1 arrays. I didn’t realise however that it came without any cache so would only work by directly writing straight to the disk, and the performance was horrible. So I then brought the 512MB Flash Backed Write Cache (FBWC) memory module as I was under the impression that with FBWC I would not need a battery. I got this idea from a forum post. "What do you guys think of the choice between 'BBWC' (battery backed write cache) and 'FBWC' (flash backed write cache)? The flashed based ones use non-volitile memory so need no battery." After installing the cache module however the server pretty much won’t boot. The P410 has a flashing amber light on it, and from the manual that doesn’t sound good. I’ve managed to get to the on board BIOS once and even managed to get to boot to the HP Array Configuration Utility (ACU) CD once, but every other time the Server continuingly reboots once it get to the POST screen and reads ARRAY INITILIZING %%%. The one time I reached the ACU, it reported a problem with the Cache Module. To me, it seems like the cache module is faulty, however the supplier tells me “Do you have an FBWC battery pack, p/n 587324-001, because that is required for the cache to work. If you have it, please complete an RMA form and we'll send a replacement / credit.” Does this sound right to you? I’ve been ordering the parts from the US and I don’t want to spend $77 + $40 p&p on a battery, wait a week for the shipping to find the card is faulty, and I don’t want to send back a working card?

  Read the article

• Computer keeps restarting [closed]

  - by Joris

  I have a strange problem with my desktop pc, when I start it, it just restarts immediately, it displays the bios/motherboard logo and then restarts. I can't access the bios to edit settings because it restarts to fast. Then I tried different things to fix it with mixed success. (I also tried to reset the bios without success) I noticed that a capacity from the graphics card was broken (it looked exploded) so I ordered a new graphics card & plugged it in the computer. It didn't change much, still the same problem. Then I unplugged everything that's not necessary and put only 1Gig RAM in the motherboard (usually it has 4 x 1Gig RAM) and the computer started, then I putted another gig of RAM and the computer still started. (starting=booting windows) When I putted in the 3th RAM it didn't boot anymore (again restarting all the time) so I removed this 3th gig of RAM and this is where it gets weird. I expected the computer to boot again because it is exactly the same configuration as before - which worked - but the computer didn't want to start. It just gave the same problem as before (restarting all the time.. ) Anyone an idea what might be wrong?

  Read the article

• Display issue with fresh install of windows server 2012

  - by Tony

  I installed windows server 2012 last night on my home "server". I use server loosely. From the get go I had display and graphic issues. The image was fuzzy and jumbled up during the install. This continued once booted into the install. I did installed Server 2012 twice now as the first time, I only installed "core". I know this is not a busted graphics card because it worked fine in Win7, during boot, and fine in "core" mode. Once booted into "GUI" install of Server 2012, the image was messed up again. To make things even more weird, the windows "loading" screen looks fine. Once the login screen appears the image is fuzzy and jumbled. My guess was that it was a driver issue. I did try to install the win8 x64 drivers from nvidia. This caused the system to become unbootable and I had to restore to a previous working point and uninstall the driver. I did try two different monitors and cables. Also both ports on the back of the video card. I did manage to get RDP running and that works fine. I rarely work directly on this machine but it would be nice to have the option back. Geforce 210, AMD 4600+, 4 gigs of ram.

  Read the article

• Slow, choppy video playback with nVidia 8600GT

  - by user5351

  I have an nVidia 8600GT card (made by EVGA) on a machine with Windows Vista (AMD Athlon X2 processors) and four gigs of ram. It runs pretty good, but I have had some slow/choppy/stuterring video playback issues whenever watching flash videos on Youtube or other sites. The problem is there with both Firefox and IE flash videos, but is maybe worse with Firefox. I also tried Linux with nVidia's binary drivers and it was about the same. I downloaded EVGA precision which allows me to control stuff like the fan and clock speed. The card's temp (in both Vista and Linux) is usually at 66C when idle (not playing a game or watching anything). It goes up a little when watching a video (maybe 68-72C). Any ideas on how to fix this? UPDATE: The issues are both with full screen and embedded flash videos. I have Flash 10.0.32.18 (always make sure I use most recent for security), and the CPU is an AMD Athlon 64 X2 Dual Core Processor 4000+ at 2.11 GHZ. The current GPU driver installed is the most recent GeForce one from last July.

  Read the article

• xrandr fails when 3rd monitor has higher resolution

  - by Pi3cH

  I tried many combinations with xrandr command under lubuntu 12.04 to setup my three monitors DVI (DELL 1) left detected as HDMI1 HDMI (LG E2290) middle detected as HDMI2 VGA (DELL 2) right detected as VGA1 I can get the display with fix 1280x1024 on all the monitors. But once I setup 1280x1024 + 1920x1080 + 1280x1024, I get blank screen on all the monitors. Sometimes it throws crts fail error instead of blanking out. Anyone have similar issues? any solutions/workarounds? P.S. I can setup two monitors using 1280x1280 and 1920x1080 P.S.S. HDMI2 required at least 1920x1080 to display sharp picture. Outputs (it seems graphic card supports up to 8192x8192): xrandr Screen 0: minimum 320 x 200, current 3840 x 1024, maximum 8192 x 8192 VGA1 connected 1280x1024+2560+0 (normal left inverted right x axis y axis) 338mm x 270mm 1280x1024 60.0*+ 75.0 1152x864 75.0 1024x768 75.1 60.0 800x600 75.0 60.3 640x480 75.0 60.0 720x400 70.1 HDMI1 connected 1280x1024+0+0 (normal left inverted right x axis y axis) 376mm x 301mm 1280x1024 60.0*+ 75.0 1152x864 75.0 1024x768 75.1 60.0 800x600 75.0 60.3 640x480 75.0 60.0 720x400 70.1 HDMI2 connected 1280x1024+1280+0 (normal left inverted right x axis y axis) 477mm x 268mm 1920x1080 60.0 + 1680x1050 60.0 1280x1024 75.0 60.0* 1152x864 75.0 1024x768 75.1 60.0 800x600 75.0 60.3 640x480 75.0 60.0 720x400 70.1 DP1 disconnected (normal left inverted right x axis y axis) DP2 disconnected (normal left inverted right x axis y axis) 3 CRTs (0,1 VGA, 0,1,2 for other HDMI) xrandr --verbose VGA1 connected 1280x1024+2560+0 (0x47) normal (normal left inverted right x axis y axis) 338mm x 270mm Identifier: 0x42 Timestamp: 51324 Subpixel: unknown Gamma: 1.0:1.0:1.0 Brightness: 1.0 Clones: CRTC: 0 CRTCs: 0 1 ... HDMI1 connected 1280x1024+0+0 (0x47) normal (normal left inverted right x axis y axis) 376mm x 301mm Identifier: 0x43 Timestamp: 51324 Subpixel: unknown Gamma: 1.0:1.0:1.0 Brightness: 1.0 Clones: CRTC: 1 CRTCs: 0 1 2 ... HDMI2 connected 1280x1024+1280+0 (0x47) normal (normal left inverted right x axis y axis) 477mm x 268mm Identifier: 0x44 Timestamp: 51324 Subpixel: unknown Gamma: 1.0:1.0:1.0 Brightness: 1.0 Clones: CRTC: 2 CRTCs: 0 1 2 Below command fails: xrandr --output VGA1 --auto --output HDMI2 --auto --left-of VGA1 --output HDMI1 --auto --left-of HDMI2 Below command passes: xrandr --output VGA1 --auto --output HDMI2 --mode 1280x1024 --rate 60.0 --left-of VGA1 --output HDMI1 --auto --left-of HDMI2 Graphic card VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09)

  Read the article

• Win 7 Media Center - TV - No audio on HD channels

  - by Chuzein Part II

  I wonder if you can help. I have recently purchased a PCTV Nanostick DVD-T2 290e I am running Windows 7 Home Premium 64bit and I use Windows media center for almost everything. I run a media center machine in my lounge through my Sony AV Amp onto my HD TV. I bought the Nanostick to watch ‘Freeview HD’ programmes when watching the TV through the Media Center – I also have a Sony Freeview Plus system that the Mrs uses. I installed the Nanostick with relatively no issues and as described by many user reviews Media Center picked up the new USB tuner and scanned all the new channels and I was presented with all the HD channels. The issue I have is that there is no audio sound from the HD channels but perfect video. SD works fine. The software that comes with the Nanostick works fine – both sound and vision are perfect for the HD channels. As mentioned, I run my Media Centre lots. I have an extensive DVD and BD collection stored on a server and DVD and BD all play perfectly through Arcsoft Total Media Theatre 5 – with no issues on either SD or HD. My sound card is built into my motherboard and that sends the audio signal to my gfx card and that in turn passes it through to my Sony AV Amp that decodes the audio to be heard on my 5.1 set up. Does anyone have any ideas. I have searched lots on the net and I cant find anyone else with the same issue. I am aware of codecs etc but I don’t really understand it. It also puzzles me that when I read the user/buyer reviews for this product so many people tell the story of faultless installations on the same kind of set up as me.

  Read the article

• 85 Hz on old/new driver looks the same like 75 Hz on previous one?

  - by jon

  I have old philips 107T5 CRT and Nvidia graphics card. I used old Nvidia driver (but it wasn't 'legacy' one when I installed it) for few years but recently I decided to install other Linux distribution. I used 75 Hz refresh rate and 1024x768 resolution on my previous distribution. After I installed the new distribution I had to install a Nvidia driver so I downloaded one from the Nvidia site (this time only legacy supported my card so I downloaded legacy and installed it). It wasn't automatically updating xorg.conf but I had my previous xorg.conf copy and I used it. When I run X I could only choose 85 and 75 Hz, 85 was checked as default. And now what shocks me: that default 85 Hz looks identically like 75 Hz on previous driver looked (at least to me). I tried 75 Hz out of curiosity and it's too bright, hurts, etc. But on the previous driver 75 Hz wasn't hurting my eyes. Why is it different? It's the same number after all, so it should always give the same results, right? That's my first question. Second question: Is 85 Hz OK for that monitor model? Would it break it? I tried to find the optimal refresh rate for this model but couldn't find it.

  Read the article

• How to route between 2 networks with a server with 2 network cards?

  - by LumenAlbum

  This is the first time I am faced with routing and it seems I have hit a dead end. I have the following scenario: client1: 192.168.1.10 255.255.255.0 gateway: 192.168.1.100 DNS server: 192.168.1.100 client2: 192.168.1.20 255.255.255.0 gateway: 192.168.1.100 DNS server: 192.168.1.100 server (Windows Server 2008 R2 with enabled RAS & Routing Services) network card 1 (connected to a switch along with the clients) 192.168.1.100 255.255.255.0 DNS server: 127.0.0.1 network card 2 (connected to the router) 192.168.2.100 255.255.255.0 gateway: 192.168.2.1 DNS server: 127.0.0.1 (DNS forwarding to 192.168.2.1) ISP router (with connection to internet) 192.168.2.1 Now in this scenario I have tried to route traffic from the 192.168.1.0/24 network with the clients to the 192.168.2.0/24 network with the routers to connect them to the internet. However, no matter what I do I get no positive ping to the router 192.168.2.1. Ping from 192.168.168.1.10 to 192.168.1.20: Success to 192.168.1.100: Success to 192.168.2.100: Success to 192.168.2.1: not reachable The routing table contains the 2 routes 192.168.1.0 and 192.168.2.0 as directly connected. Does anyone know where the routing fails? I have searched different forums but mostly found nothing relevant. One post however pointed out that in a similar situation the problem was that the router doesn't know the way back and the internet router would need a static route back to the first router. If that really is the case, I take it there is no solution with my equipment, because the standart ISP router doesn't allow to set any static routes.

  Read the article

• Half of installed RAM is hardware reserved

  - by user968270

  After a rather arduous and convoluted series of problems that left me without a desktop for ~80 days, I've finally got the thing up and running, having replaced the power supply, motherboard, graphics card and CPU. Now, however, I'm experiencing the 'hardware reserved RAM' issue. Perhaps this is the exhaustion talking, but looking at the question that tends to get pointed to when this kind of topic gets locked as a duplicate hasn't helped. I have 16 GB of RAM installed in an MSi 970A-G46, which is spec'd for up to 32 GB of RAM. The BIOS recognizes that I have 16 GB installed, and the resource monitor also shows the whole 16 GB, only it shows 8 GB as hardware reserved. I've seen suggestions that it's an OS issue, but the particular installation of Windows 7 (64-bit) which I'm running on my boot drive is the same as the one that could actually access the 16 GB in my previous motherboard (MSi 870A-G54). I've updated my BIOS using the MSi Live Update tool and restarted the machine with no effect, and I cannot seem to locate any 'Memory Remapping' option as I've seen mentioned. I've physically swapped the RAM between the slots to no effect. I've unchecked the Maximum Memory box in the msconfig Boot tab's advanced options, also to no effect. These are my system's basic specifications OS: Windows 7 Home Premium (64-Bit) Motherboard: MSi 970A-G46 CPU: AMD FX-8150 Graphics Card: XFX Radeon HD 6870 Boot Drive: OCZ Agility 3 Storage Drive: Samsung Spinpoint F3 ST1000DM005/HD103SJ 1TB PSU: Thermaltake TR-2 TR600 600W ATX12V v2.3

  Read the article

• Windows-7 Ultimate 64 bit wont connect to my wired/wireless networks.

  - by A302

  Windows 7 Ultimate 64 bit. Everything was working fine & then just stopped working. The nic card Realtek PCIe GBE Family Controller is enabled but does not connect to my router (cables & router ports are good). Wireless Atheros AR5007EG is enabled but the connection is limited (encryption type / key have been verified). A laptop running XP can connect both wired / wireless. SSID is not being broadcast, connect to network if it is not broadcasting is checked. Have checked services.msc for Bonjour & did not see it listed. Network & sharing center does not list any active networks. Device manager lists both devices as functioning properly. Router configuration has not been changed. Virus scan has not found anything. I would like to fix this rather than using Acronis to do a system restore. Thanks in advance for any advice offered in solving this. 26 Jan, the nic card & wireless are working using PCLinux OS Live CD. It appears that the problem is Windows 7 related.

  Read the article

• What switch should we use for PCoIP?

  - by Jay R.

  We have a small lab space that seats 10 people and has 20 machines. Each machine is set to 1920x1200 resolution because the user apps are best used at that resolution. Currently the machines are all located close enough to montors that a DisplayPort cable will reach, but the pending lab remodel positions them around 80 feet or more away in racks. Our proposed solution is to use PCoIP. We purchased 10 PCoIP portals and 20 PCoIP host cards. We plan to set up a dedicated network to handle just the PCoIP traffic. After testing just one portal and one host card with a cheap 1G switch from a local office supply store, we were left with less than good impressions about the usefulness in our lab. The framerates were not spectacular and the mouse seemed jerky. Our concern is that we can't get away with the cheap 1G stuff from the store because adding more machines to the switch will just make the user experience worse. What switch would be recommended to best support our PCoIP situation? We will need to plug in at least 30 cables based on just those machines. Is there a particular feature to search for that makes a difference? Is there a switch that works best with PCoIP? Added Info: The reporting webapp for the host card shows maximum bandwidth usage to be 220000 kbps. The average appears to be around 180000 kbps. The reverse direction is much lower, like 15000 kbps.

  Read the article

• Onboard Ethernet suddenly stopped working to router

  - by AfterschoolHobbist

  Hey guys, yesterday I have a sudden problem of my Ethernet connection to my router. My computer is a Pendium 4 with Window XP SP3 running on it and it was working fine earlier in the day, but yesterday night was the start of the problem. My computer is unable to ping to the router and to any other website and unable to get internet connection. As beside it was connected to a hub, I directly connected it to the router directly and the same problem occurred, being unable to ping to the router (and connecting to it) and still no internet access. My directly connected to the modem and the problem still persisted. For each connection, I connected it to my computer and my laptop and my laptop was able to connect, while my desktop computer was unable. I wondered if it was a OS issue and ran a live Ubuntu CD to see if Ubuntu was able to connect to the internet, but the issue persisted and I was unable to get internet access. I then set my router's lease time to 1 hour and waited. After 1 hour, the lease for my computer was removed and I hoped this worked, but it didn't work, but something strange is acting up. My desktop computer is still unable to ping to the router or connect to the internet, but for some reason, my router and desktop computer is still able to contact each other by providing a lease of an local ip address. The router record of a lease to my desktop computer, and when I do ipconfig, my desktop also recognize that it has been provided a local ip address. I have concluded that this is a hardware issue and the only solution to fix this is to by a network card adapter, but I am wondering if anyone has any solutions that could explain why this happen, why my mac address is 01-23-45-67-89-ab, and is there any way to fix it without buying a new network card? Thanks in advance.

  Read the article

• Getting dwl-g122 to work on ubuntu

  - by User1

  I have a USB WiFi adapter, D-Link dwl-g122. I'm running Ubuntu 10.4. My laptop has a built-in wireless card that is connecting fine to the router. I plug in the usb and it never really connects. Here are some details: iwconfig wlan1 IEEE 802.11bg ESSID:"\x0B\xE1..." Mode:Managed Frequency:2.457 GHz Access Point: Not-Associated Tx-Power=19 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on lshw -c network: *-network:1 description: Wireless interface physical id: 3 logical name: wlan1 serial: 00:13:46:8b:xx:xx capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=IEEE 802.11bg dmesg [ 1096.814176] wlan1: direct probe to AP xxx (try 1) [ 1096.820960] wlan1: direct probe responded [ 1096.820969] wlan1: authenticate with AP xxx (try 1) [ 1096.823790] wlan1: authenticated [ 1096.823869] wlan1: associate with AP xxx (try 1) [ 1096.827667] wlan1: RX AssocResp from xxx (capab=0x411 status=0 aid=1) [ 1096.827674] wlan1: associated [ 1142.590912] wlan1: deauthenticating from xxx by local choice (reason=3) lsmod|rt2 rt2500usb 19643 0 rt2x00usb 11260 1 rt2500usb rt2x00lib 32133 2 rt2500usb,rt2x00usb mac80211 238896 3 ath5k,rt2x00usb,rt2x00lib cfg80211 148725 4 ath5k,ath,rt2x00lib,mac80211 led_class 3764 3 ath5k,rt2x00lib,sdhci It looks like the driver loads but it doesn't feel like connecting. The behavior is identical even if I blacklist the other wifi card (using an ath5k driver). It's almost like it is using the wrong password or something. Does anyone know what is happening? Is anyone using Ubuntu successful?

  Read the article

• what are these weird IP address connections in resource monitor?

  - by bill

  I decided to check out Resource Monitor (on the 'Performance' tab in Task Manager, Windows 7) and I noticed in the "Network" section that the 'System' image name kept making a bunch (~5 at a time) of connections to random IP addresses, it would show anywhere from 1-500 bytes/sec 'sent'. They would stay connected for 1-2 minutes. -All web browsers are closed So, first thing I did was run a trace from network-tools.com on some of these IP addresses. 8/10 were outside of US and did not resolve to any host name. Of the 10 IP addresses I traced, 2 were in US, 4 showed origins in China, and one each to Algeria, Russia, Pakistan, Korea. (!) So, the next thing I did was turn off my wireless card, watch the connections disappear, then turn the card back on, and within 30 seconds more random connections were created by System, with different IP addresses from the first time. The next thing I did was go open Task Manager, Show Processes From All Users, then I killed just about everything that wasn't (what appeared to be) a windows process. Turned on wi-fi, and again within 30 seconds, random IP addresses connect for ~ 1 min at a time, new ones coming and going. I occasionally use bit torrent on this machine, but there was definitely no process that seemed related to bt running after I went through task manager, and bt wasn't open to begin with. So, any ideas on what these connections might be for? I have been using Ad-Aware Free and AVG Free on this computer for a while now, always up to date..

  Read the article

• Dropbox picture sync: Skip RAW files?

  - by Steven Lu

  I like the convenience of having Dropbox keep track of my photos because it tends to work with my devices over 3G (I am often tethering to my phone with my iPad and Macbook) as well as Wifi, but it's a waste of network traffic to sync the raw files from my camera or memory card. It clutters up the dropbox list and the files are just huge. Is there a way to configure the Dropbox client so that it ignores a certain file extension for the picture sync? Also, I suspect that if I just go and delete the raw files, that the next time I plug in the memory card and tell Dropbox to sync, it will re-download the raw files. Which would be terribad. I could switch to iCloud for Photo Stream, I suppose, but there will be no access via 3G that way. And I've already got years of experience with Dropbox so I know it's going to just work. I think any method that works for filtering files to exclude from sync on Dropbox in general should work here too. Edit: Wow there are 19k votes for this exact request.

  Read the article

• How can I read PDFs with e-reader on a Lenovo tablet?

  - by Jack M

  This is my first time using a tablet and I'm totally lost - this must be what computers look like to old people. This is a Lenovo Thinkpad tablet. I don't see a specific model number on it (it was passed down to me second hand). What I'd like to do is read a PDF. I'm fairly certain I successfully transferred the PDF onto the tablet via an SD card, and I noticed this thing has an app called "eReader" on it, so I started that up. All I see are empty bookshelves, and no obvious buttons or settings anywhere. I saw in multiple places that you have to, as one site puts it: ...copy and paste the relevant files into the eBooks folder and they will appear on the eReader shelf for your consumption... But I have no idea how to: Access the file system. Locate the eBooks folder. Copy and paste files. Will I need a file explorer app? If so, how can I install that given that my only method of getting data onto this tablet is an SD card (no wireless internet).

  Read the article

• Disk operations in windows 7 are slow

  - by Skadlig

  My computer started lagging last Sunday. I tried to reboot it and it failed. Trying to boot into failsafe mode takes around two hours. It mainly freezes on two files: scsiport.sys and classpnp.sys When it finally has started all disc operations are really slow. When it has run for a while it goes faster, probably due to data moved into RAM instead. It froze on an other file before that was associated with Avast but uninstalling it didn't really help. A critical windows update was installed on Sunday but rolling back the update didn't help. I had a guess about the sound card but disabling the sound card drivers also didn’t help. I have an inkling of an idea that it might be Intel rapid storage technology that might be acting up but it doesn't allow me to reinstall it from failsafe mode and I haven't been able to log into normal mode for a while. I would appreciate suggestions regarding how to get into normal mode again and/or what can be the root cause.

  Read the article

< Previous Page | 143 144 145 146 147 148 149 150 151 152 153 154  | Next Page >