Search Results

Search found 18911 results on 757 pages for 'device manager'.

Page 148/757 | < Previous Page | 144 145 146 147 148 149 150 151 152 153 154 155  | Next Page >

• Ubuntu 14.04:LTS , HPLIP loses USB connection to HP laserjet

  - by Gareth

  This is my first post, so please let me know if i have inadvertanly broken any rules. Problem There seems to be a problem with HPLIP and USB connections in ubuntu 14.04LTS. After upgrading i managed to get the printing to work but today it has broken. Initial Issue (Solved) After upgrading to unbutntu 14.04 LTS my printer lHP LaserJet 1018 stopped printing (code=12) Looking through the Forumsthere are several issues with printitng and HPLIP so I was able to troubleshoot this. The steps I took were : Reran HPdoctor Ran hp-check Un-installed and installed the latest version of HPLIP (3.14.4) Checked the USB connections lsusb and lsusb-v Re-ran hpcheck Removed the printer from HPLIP Re-ran hpcheck Manually configued HPLIP to the printer hp-setup-g <xxx:yyy> And this worked HPLIP was able to see the printer in the USB , test page printed and was happily working for a few weeks. Current Issue Printer Not working However today my wife complains the printer is not working and checking see that although HPLIP has the same error code and did not seem to be able to see the printer although running lsusb could see the printer. Initially thought this may be due to usb given a new bus/device after being turned on and off and went to repeat the steps above at the moment still seeing an error in that the HPLIP is complaining that it cannot see the device **error: Device not found. Please make sure your printer is properly connected and powered-on.** current Observations lsusb output ## Bus 002 Device 007: ID 03f0:4117 Hewlett-Packard LaserJet 1018 sudo hp-check output *> "duan@duan-Lenovo-B550:~$ sudo hp-check [sudo] password for duan: Saving output in log file: /home/duan/hp-check.log HP Linux Imaging and Printing System (ver. 3.14.4) Dependency/Version Check Utility ver. 15.1 Copyright (c) 2001-13 Hewlett-Packard Development Company, LP This software comes with ABSOLUTELY NO WARRANTY. This is free software, and you are welcome to distribute it under certain conditions. See COPYING file for more details. Note: hp-check can be run in three modes: 1. Compile-time check mode (-c or --compile): Use this mode before compiling the HPLIP supplied tarball (.tar.gz or .run) to determine if the proper dependencies are installed to successfully compile HPLIP. Run-time check mode (-r or --run): Use this mode to determine if a distro supplied package (.deb, .rpm, etc) or an already built HPLIP supplied tarball has the proper dependencies installed to successfully run. Both compile- and run-time check mode (-b or --both) (Default): This mode will check both of the above cases (both compile- and run-time dependencies). Full Output output of hp-setup -g 002:007 window box "device not found please make sure your printer is properly connected and powered on" duan@duan-Lenovo-B550:~$ sudo hp-setup -g 002:007 [sudo] password for duan: > HP Linux Imaging and Printing System (ver. 3.14.4) Printer/Fax Setup > Utility ver. 9.0 > > Copyright (c) 2001-13 Hewlett-Packard Development Company, LP This > software comes with ABSOLUTELY NO WARRANTY. This is free software, and > you are welcome to distribute it under certain conditions. See COPYING > file for more details. > > hp-setup[18461]: debug: param=002:007 hp-setup[18461]: debug: > selected_device_name=None Fontconfig error: > "/etc/fonts/conf.d/65-khmer.conf", line 14: out of memory Fontconfig > error: "/etc/fonts/conf.d/65-khmer.conf", line 23: out of memory > Fontconfig error: "/etc/fonts/conf.d/65-khmer.conf", line 32: out of > memory hp-setup[18461]: debug: Sys.argv=['/usr/bin/hp-setup', '-g', > '002:007'] printer_name=None param=002:007 jd_port=1 device_uri=None > remove=False Searching for device... hp-setup[18461]: debug: Trying > USB with bus=002 dev=007... hp-setup[18461]: debug: Not found. > hp-setup[18461]: debug: Trying serial number 002:007 hp-setup[18461]: > debug: Probing bus: usb hp-setup[18461]: debug: Probing bus: par > error: Device not found. Please make sure your printer is properly > connected and powered-on. hp-setup[18461]: debug: Starting GUI loop. .. USB lead Works with the Windows 7 laptop Printer Works with windows 7 laptop Questions Is this a Bug with HPLIP or an issue with laptop/printer? Supplementary question if it is a bug what information is needed and where should it be sent ? Any suggestions on how to get the printer to work correctly with Ubuntu 14.04LTS/HPLIP 13.4.3 so that it stays working ?

  Read the article

• Qt: how to build QML apps for Symbian devices?

  - by DaveJohnston

  I am pretty new to Qt and I have just started looking at QML. There are some sample applications included with the Nokia Qt SDK for Symbian and I have managed to load them into Qt Creator and run them using the QML Viewer application on the desktop. I would like to try some of the samples out on a device, but I am totally clueless as to how I would go about getting the qml files to run on a device. Are they first packaged into a sis file and installed or is the folder simply copied over? If so how is the app started on the device? Having done some googling the only information I seem to be able to find says that the Qt libraries available for Symbian devices at the moment is only 4.6.3 whereas version 4.7.0 is required for QML apps? Does this mean that I won't be able to run QML apps on a device at the moment? (Device is S60 5th Edition) Any help or pointers in the right direction for more information would be much appreciated.

  Read the article

• Super Joybox 5 HID 0925:8884 not recognized as joystick in Ubuntu 12.04 LTS

  - by Tim Evans

  Problem: When using the "Super JoyBox 5" 4 port playstation 2 to USB adapter, the device is not recognized as a joystick. there is no js0 created, but instead another input eventX and mouseX are created in /dev/input. When using the directional buttons (up down left right) on a Playstation 1 controller attached to the device, the mouse cursor moves to the top, bottom, left, and right edges of the screen respectively. Buttons are unresponsive. The joypads attached to the device cannot be used in any games or other programs. Attempted remedies: Creating a symlink from the eventX to js0 does not solve the problem. Addl Info: joydev is loaded and running peroperly according to LSMOD. evtest can be run on the created eventX (sudo evtest /dev/input/event14 in my case) and the buttons and axes all register inputs. Here is a paste of EVTEST's diagnostic and the first couple button events. [code] sudo evtest /dev/input/event14 Input driver version is 1.0.1 Input device ID: bus 0x3 vendor 0x925 product 0x8884 version 0x100 Input device name: "HID 0925:8884" Supported events: Event type 0 (EV_SYN) Event type 1 (EV_KEY) Event code 288 (BTN_TRIGGER) Event code 289 (BTN_THUMB) Event code 290 (BTN_THUMB2) Event code 291 (BTN_TOP) Event code 292 (BTN_TOP2) Event code 293 (BTN_PINKIE) Event code 294 (BTN_BASE) Event code 295 (BTN_BASE2) Event code 296 (BTN_BASE3) Event code 297 (BTN_BASE4) Event code 298 (BTN_BASE5) Event code 299 (BTN_BASE6) Event code 300 (?) Event code 301 (?) Event code 302 (?) Event code 303 (BTN_DEAD) Event code 304 (BTN_A) Event code 305 (BTN_B) Event code 306 (BTN_C) Event code 307 (BTN_X) Event code 308 (BTN_Y) Event code 309 (BTN_Z) Event code 310 (BTN_TL) Event code 311 (BTN_TR) Event code 312 (BTN_TL2) Event code 313 (BTN_TR2) Event code 314 (BTN_SELECT) Event code 315 (BTN_START) Event code 316 (BTN_MODE) Event code 317 (BTN_THUMBL) Event code 318 (BTN_THUMBR) Event code 319 (?) Event code 320 (BTN_TOOL_PEN) Event code 321 (BTN_TOOL_RUBBER) Event code 322 (BTN_TOOL_BRUSH) Event code 323 (BTN_TOOL_PENCIL) Event code 324 (BTN_TOOL_AIRBRUSH) Event code 325 (BTN_TOOL_FINGER) Event code 326 (BTN_TOOL_MOUSE) Event code 327 (BTN_TOOL_LENS) Event code 328 (?) Event code 329 (?) Event code 330 (BTN_TOUCH) Event code 331 (BTN_STYLUS) Event code 332 (BTN_STYLUS2) Event code 333 (BTN_TOOL_DOUBLETAP) Event code 334 (BTN_TOOL_TRIPLETAP) Event code 335 (BTN_TOOL_QUADTAP) Event type 3 (EV_ABS) Event code 0 (ABS_X) Value 127 Min 0 Max 255 Flat 15 Event code 1 (ABS_Y) Value 127 Min 0 Max 255 Flat 15 Event code 2 (ABS_Z) Value 127 Min 0 Max 255 Flat 15 Event code 3 (ABS_RX) Value 127 Min 0 Max 255 Flat 15 Event code 4 (ABS_RY) Value 127 Min 0 Max 255 Flat 15 Event code 5 (ABS_RZ) Value 127 Min 0 Max 255 Flat 15 Event code 6 (ABS_THROTTLE) Value 127 Min 0 Max 255 Flat 15 Event code 7 (ABS_RUDDER) Value 127 Min 0 Max 255 Flat 15 Event code 8 (ABS_WHEEL) Value 127 Min 0 Max 255 Flat 15 Event code 9 (ABS_GAS) Value 127 Min 0 Max 255 Flat 15 Event code 10 (ABS_BRAKE) Value 127 Min 0 Max 255 Flat 15 Event code 11 (?) Value 127 Min 0 Max 255 Flat 15 Event code 12 (?) Value 127 Min 0 Max 255 Flat 15 Event code 13 (?) Value 127 Min 0 Max 255 Flat 15 Event code 14 (?) Value 127 Min 0 Max 255 Flat 15 Event code 15 (?) Value 127 Min 0 Max 255 Flat 15 Event code 16 (ABS_HAT0X) Value 0 Min -1 Max 1 Event code 17 (ABS_HAT0Y) Value 0 Min -1 Max 1 Event code 18 (ABS_HAT1X) Value 0 Min -1 Max 1 Event code 19 (ABS_HAT1Y) Value 0 Min -1 Max 1 Event code 20 (ABS_HAT2X) Value 0 Min -1 Max 1 Event code 21 (ABS_HAT2Y) Value 0 Min -1 Max 1 Event code 22 (ABS_HAT3X) Value 0 Min -1 Max 1 Event code 23 (ABS_HAT3Y) Value 0 Min -1 Max 1 Event type 4 (EV_MSC) Event code 4 (MSC_SCAN) Testing ... (interrupt to exit) Event: time 1351223176.126127, type 4 (EV_MSC), code 4 (MSC_SCAN), value 90001 Event: time 1351223176.126130, type 1 (EV_KEY), code 288 (BTN_TRIGGER), value 1 Event: time 1351223176.126166, -------------- SYN_REPORT ------------ Event: time 1351223178.238127, type 4 (EV_MSC), code 4 (MSC_SCAN), value 90001 Event: time 1351223178.238130, type 1 (EV_KEY), code 288 (BTN_TRIGGER), value 0 Event: time 1351223178.238167, -------------- SYN_REPORT ------------ Event: time 1351223180.422127, type 4 (EV_MSC), code 4 (MSC_SCAN), value 90002 Event: time 1351223180.422129, type 1 (EV_KEY), code 289 (BTN_THUMB), value 1 Event: time 1351223180.422163, -------------- SYN_REPORT ------------ Event: time 1351223181.558099, type 4 (EV_MSC), code 4 (MSC_SCAN), value 90002 Event: time 1351223181.558102, type 1 (EV_KEY), code 289 (BTN_THUMB), value 0 Event: time 1351223181.558137, -------------- SYN_REPORT ------------ Event: time 1351223182.486137, type 4 (EV_MSC), code 4 (MSC_SCAN), value 90003 Event: time 1351223182.486140, type 1 (EV_KEY), code 290 (BTN_THUMB2), value 1 Event: time 1351223182.486172, -------------- SYN_REPORT ------------ Event: time 1351223183.302130, type 4 (EV_MSC), code 4 (MSC_SCAN), value 90003 Event: time 1351223183.302132, type 1 (EV_KEY), code 290 (BTN_THUMB2), value 0 Event: time 1351223183.302165, -------------- SYN_REPORT ------------ Event: time 1351223184.030133, type 4 (EV_MSC), code 4 (MSC_SCAN), value 90004 Event: time 1351223184.030136, type 1 (EV_KEY), code 291 (BTN_TOP), value 1 Event: time 1351223184.030166, -------------- SYN_REPORT ------------ Event: time 1351223184.558135, type 4 (EV_MSC), code 4 (MSC_SCAN), value 90004 Event: time 1351223184.558138, type 1 (EV_KEY), code 291 (BTN_TOP), value 0 Event: time 1351223184.558168, -------------- SYN_REPORT ------------ [/code] The directional buttons on the pad are being identified as HAT0Y and HAT0X axes, thats zero, not the letter O. Aparently, this device used to work flawlessly on kernel 2.4.x systems, and even as late as ubunto 10.04. Perhaps the Joydev rules for identifying joypads has changed? Currently, this kind of bug is affecting a few different type of controller adapters, but since this is the one that i PERSONALLY have (and has been driving me my own special brand of crazy), its the one im documenting. What i think should be happening instead: The device should be registering js0 through js3, one for each port, or JS0 that will handle all of the connected devices with different numbered axes for each connected joypad. Either way, it should work as a joystick and stop controlling the mouse cursor. Please help!

  Read the article

• C# SerialPort.GetPortNames() behavior

  - by Gunner

  In my C# 2008 application, I use the SerialPort.GetPortNames() function to retrieve the list of currently available ports. What I have noticed is, when ever I plug in a USB device, it's port number i s shown in the list on my Application and when I unplug it and refresh the list, the port number is no longer there. One phase of the application involves reading/writing data from/to the device continuously. Now, my expectation is, If I unplug the device during the operation and get the current Port list using SerialPort.GetPortNames(), the Port Name will not be there and I can use that to make the decision that the device has been unplugged. To my surprise, the Port name is still found despite having it removed Why is the program behaving like this? The port name isn't listed when in no-communication mode. Does it have something to do with the device being removed when it's communicating?

  Read the article

• Unicenter Software Delivery 4 not able to connect to MS SQL 2000 Database after W2003 SP2 upgrade

  - by grub

  Hello Everyone Yesterday I installed the Windows Server 2003 Service Pack 2 on a Windows Server 2003 which has Unicenter Software Delivery 4 installed. Prior to the installation I disabled every CA service on the server (Brightstor, SDO , RCO, TNG) and the MS SQL 2000 service. After the installation of the SP2 I enabled the services again but the Unicenter Service is not able to connect to the MS SQL 2000 Database anymore. The database itself is up and running and I can connect to it with the Enterprise Manager. A dbcc checkdb doesnt return any errors on the Unicenter database. The Unicenter service throws the following error messages during startup: IM[1] 27/05 10:38:31,272 Installation Manager in init phase IM[1] 27/05 10:38:31,694 Process IM(L) - [004152] failed to open database SDDATA. dbopen() call failed. IM[1] 27/05 10:38:31,694 sqls error details: IM[1] 27/05 10:38:31,694 (null) IM[1] 27/05 10:38:32,069 ##EXCEPTION## TableError T@:PS_SQLS\isam_db.cxx:744. IM[1] 27/05 10:38:32,069 ##EXCEPTION## TableError C@:TaskmgrL\ASMTML.CXX:596. IM[1] 27/05 10:38:32,069 ##EXCEPTION## ErrorCode: 4711 in SDDATA:Isam::Isam. Process IM(L) - [004152] failed to open database SDDATA. dbopen() call failed. IM[1] 27/05 10:38:32,069 sqls error details: IM[1] 27/05 10:38:32,069 (null) IM[1] 27/05 10:38:32,069 returned 0. IM[1] 27/05 10:38:32,084 Persistent Storage could not be opened. Error cause is found in the ASM Event Log. Restart Task Manager. IM[1] 27/05 10:38:32,084 Failed to open database. IM[1] 27/05 10:38:32,084 Installation Manager ends> If I check the Unicenter configutation with *chkmib_l* the tool throws an exception and creates a small dump file. An Exception Occurred: Time: 27/05 09:49:38,928 Reason: ChkMIB_l.exe caused an UNKNOWN_EXCEPTION in module kernel32.dll at 7C82001B:77E4BEE7 Registers: EAX=0012F908 EBX=00000000 ECX=00000000 EDX=02410004 ESI=0012F998 EDI=0012F998 EBP=0012F958 ESP=0012F904 EIP=77E4BEE7 FLG=00000206 CS =7C82001B DS =B90023 SS =120023 ES =120023 FS =7C82003B GS =3F0000 Call Stack: 7C82001B:77E4BEE7 (0xE06D7363 0x00000001 0x00000003 0x0012F98C) kernel32.dll 7C82001B:77BB3259 (0x0012F9B8 0x2B017C50 0x2B024404 0x00B68C98) MSVCRT.dll 7C82001B:2B010C42 (0x00020003 0x010C00FE 0x003F0190 0x00B69050) PS.dll << SOFTWARE DELIVERY INSTANCE INFO >> TRIGGER 0(1) instances: JCE 0(1) instances: TM 0(1) instances: IM 0(1) instances: DM 0(1) instances: DPU 0(71) instances: NATF 0(1) instances: MIBCONV 0(0) instances: API 0(4) instances: DTSFT 0(0) instances: TNGPOP 0(0) instances: DGATE 0(0) instances: << FLUSHING MEMORY TRACES >> << STOP FLUSHING MEMORY TRACES >> I compared the configuration of the SDO service and the system configuration with another server on which the Windows Server 2003 SP2 is installed and SDO is working. The configuration is the same and the same driver and software versions are used. Do you have any idea what causes the connection issue? Should I deinstall the unicenter service and make a fresh installation on the server or should I remove the Windows Server 2003 SP2? I don't want to remove the SP2 because it's a requirement for WSUS3 SP2 and I really don't want to know how many possible exploits are possible in such an old system ;-) Thank you very much and have a nice day. Below you can find more detailed information about the system and the SDO service. psinfo output (system information) System information for \\CZZAAS1003: Uptime: 0 days 14 hours 38 minutes 50 seconds Kernel version: Microsoft Windows Server 2003, Multiprocessor Free Product type: Standard Edition Product version: 5.2 Service pack: 2 Kernel build number: 3790 Install date: 23.9.2004, 11:16:11s IE version: 6.0000 System root: C:\WINDOWS Processors: 2 Processor speed: 2.3 GHz Processor type: Intel(R) Xeon(TM) CPU Physical memory: 1024 MB Video driver: RAGE XL PCI Family (Microsoft Corporation) sdver output (Unicenter Software delivery version) Unicenter Software Delivery 4.0 SP1 I2 ENU [2901] Copyright 2004 Computer Associates International, Incorporated ms sql 2000 version and odbc driver version MS SQL 2000 Server Standard Edition Product Version: 8.00.760 (SP3) ODBC Driver: SQL Server - Version 2000.86.3959.00 complete Unicenter Software delivery service log file TRIGGER[1] 27/05 10:38:28,366 SD Trigger Agent has started NATF[1] 27/05 10:38:28,928 Initiation phase finished IM[1] 27/05 10:38:31,272 Installation Manager in init phase IM[1] 27/05 10:38:31,694 Process IM(L) - [004152] failed to open database SDDATA. dbopen() call failed. IM[1] 27/05 10:38:31,694 sqls error details: IM[1] 27/05 10:38:31,694 (null) IM[1] 27/05 10:38:32,069 ##EXCEPTION## TableError T@:PS_SQLS\isam_db.cxx:744. IM[1] 27/05 10:38:32,069 ##EXCEPTION## TableError C@:TaskmgrL\ASMTML.CXX:596. IM[1] 27/05 10:38:32,069 ##EXCEPTION## ErrorCode: 4711 in SDDATA:Isam::Isam. Process IM(L) - [004152] failed to open database SDDATA. dbopen() call failed. IM[1] 27/05 10:38:32,069 sqls error details: IM[1] 27/05 10:38:32,069 (null) IM[1] 27/05 10:38:32,069 returned 0. IM[1] 27/05 10:38:32,084 Persistent Storage could not be opened. Error cause is found in the ASM Event Log. Restart Task Manager. IM[1] 27/05 10:38:32,084 Failed to open database. IM[1] 27/05 10:38:32,084 Installation Manager ends TM[1] 27/05 10:38:32,116 Task Manager in init phase TM[1] 27/05 10:38:32,334 Process TM(L) - [006132] failed to open database SDDATA. dbopen() call failed. TM[1] 27/05 10:38:32,334 sqls error details: TM[1] 27/05 10:38:32,334 (null) TM[1] 27/05 10:38:32,381 ##EXCEPTION## TableError T@:PS_SQLS\isam_db.cxx:744. TM[1] 27/05 10:38:32,381 ##EXCEPTION## TableError C@:TaskmgrL\ASMTML.CXX:596. TM[1] 27/05 10:38:32,381 ##EXCEPTION## ErrorCode: 4711 in SDDATA:Isam::Isam. Process TM(L) - [006132] failed to open database SDDATA. dbopen() call failed. TM[1] 27/05 10:38:32,381 sqls error details: TM[1] 27/05 10:38:32,381 (null) TM[1] 27/05 10:38:32,381 returned 0. TM[1] 27/05 10:38:32,381 Persistent Storage could not be opened. Error cause is found in the ASM Event Log. Restart Task Manager. TM[1] 27/05 10:38:32,381 Failed to open database. TM[1] 27/05 10:38:32,381 Task Manager ends DM[1] 27/05 10:38:33,272 Dialogue Manager is now active API[1] 27/05 10:38:34,397 API Server Process in init phase API[1] 27/05 10:38:34,397 API - SDNLS_Init API[1] 27/05 10:38:34,397 API - connectEM API[1] 27/05 10:38:34,412 API - apiServ.init DM[1] 27/05 10:38:34,678 **AND** 1 Agents triggered API[1] 27/05 10:38:34,709 Process API(L) - [005680] failed to open database SDDATA. dbopen() call failed. API[1] 27/05 10:38:34,709 sqls error details: API[1] 27/05 10:38:34,709 (null) API[1] 27/05 10:38:34,756 ##EXCEPTION## TableError T@:PS_SQLS\isam_db.cxx:744. API[1] 27/05 10:38:34,756 ##EXCEPTION## TableError C@:MainAPIL\APISERVL.CXX:246. API[1] 27/05 10:38:34,756 ##EXCEPTION## ErrorCode: 4711 in SDDATA:Isam::Isam. Process API(L) - [005680] failed to open database SDDATA. dbopen() call failed. API[1] 27/05 10:38:34,756 sqls error details: API[1] 27/05 10:38:34,756 (null) API[1] 27/05 10:38:34,756 returned 0. API[1] 27/05 10:38:34,756 Open of the database failed. API[1] 27/05 10:38:34,756 API - apiServ.init complete API[1] 27/05 10:38:34,756 API - start_APIServer DM[1] 27/05 10:38:34,803 CZZAAR1037 DPU[1:CZZAAR1037] 27/05 10:38:35,772 DPU in init phase DPU[1:CZZAAR1037] 27/05 10:38:36,100 >> GetManagerData DPU[1:CZZAAR1037] 27/05 10:38:36,287 >> SetCompInfo DPU[1:CZZAAR1037] 27/05 10:38:36,334 >> GetContainerList DPU[1:CZZAAR1037] 27/05 10:38:36,350 getJobState 3 from 5b6ad DPU[1:CZZAAR1037] 27/05 10:38:36,350 getJobState 3 from 5b6ad DPU[1:CZZAAR1037] 27/05 10:38:36,350 getJobState 3 from 5b6b7 DPU[1:CZZAAR1037] 27/05 10:38:36,350 getJobState 3 from 5b6b7 DPU[1:CZZAAR1037] 27/05 10:38:36,350 getJobState 3 from 5b6c1 DPU[1:CZZAAR1037] 27/05 10:38:36,350 getJobState 3 from 5b6c1 DPU[1:CZZAAR1037] 27/05 10:38:36,366 getJobState 3 from 5b6cb DPU[1:CZZAAR1037] 27/05 10:38:36,366 getJobState 3 from 5b6cb DPU[1:CZZAAR1037] 27/05 10:38:36,366 getJobState 3 from 5b6f9 DPU[1:CZZAAR1037] 27/05 10:38:36,366 getJobState 3 from 5b6f9 DPU[1:CZZAAR1037] 27/05 10:38:36,366 getJobState 3 from 5b71a DPU[1:CZZAAR1037] 27/05 10:38:36,366 getJobState 3 from 5b71a DPU[1:CZZAAR1037] 27/05 10:38:36,366 getJobState 3 from 5b724 DPU[1:CZZAAR1037] 27/05 10:38:36,381 getJobState 3 from 5b724 DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b72e DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b72e DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b738 DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b738 DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b742 DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b742 DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b74c DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b74c DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b756 DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b756 DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b78a DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b78a DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b7af DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b7af DPU[1:CZZAAR1037] 27/05 10:38:36,522 >> SetCompAttr DPU[1:CZZAAR1037] 27/05 10:38:36,569 >> SetDetected DPU[1:CZZAAR1037] 27/05 10:38:36,584 disconnect DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b6ad DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b6b7 DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b6c1 DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b6cb DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b6f9 DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b71a DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b724 DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b72e DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b738 DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b742 DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b74c DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b756 DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b78a DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b7af DPU[1:CZZAAR1037] 27/05 10:38:36,584 DPU ends DM[1] 27/05 10:38:38,006 **AND** 0 Agents triggered JCE[1] 27/05 10:38:38,053 JCE starts DM[1] 27/05 10:38:38,287 CZZAAS1003 DPU[2:CZZAAS1003] 27/05 10:38:38,412 DPU in init phase DPU[2:CZZAAS1003] 27/05 10:38:38,647 >> GetManagerData DPU[2:CZZAAS1003] 27/05 10:38:38,756 >> SetCompInfo DPU[2:CZZAAS1003] 27/05 10:38:38,787 >> GetContainerList DM[1] 27/05 10:38:38,850 **AND** 1 Agents triggered DM[1] 27/05 10:38:38,928 CZZAAR1124 DPU[3:CZZAAR1124] 27/05 10:38:39,053 DPU in init phase DPU[3:CZZAAR1124] 27/05 10:38:39,272 >> GetManagerData DM[1] 27/05 10:38:39,334 **AND** 1 Agents triggered DPU[3:CZZAAR1124] 27/05 10:38:39,381 >> SetCompInfo DPU[3:CZZAAR1124] 27/05 10:38:39,412 >> GetContainerList DM[1] 27/05 10:38:39,412 CZZAAR1125 DPU[3:CZZAAR1124] 27/05 10:38:39,428 getJobState 3 from 5b88e DPU[3:CZZAAR1124] 27/05 10:38:39,428 getJobState 3 from 5b88e DPU[2:CZZAAS1003] 27/05 10:38:39,491 >> SetCompAttr DPU[3:CZZAAR1124] 27/05 10:38:39,522 >> SetCompAttr DPU[4:CZZAAR1125] 27/05 10:38:39,522 DPU in init phase DPU[3:CZZAAR1124] 27/05 10:38:39,584 >> SetDetected DPU[2:CZZAAS1003] 27/05 10:38:39,584 >> SetDetected DPU[3:CZZAAR1124] 27/05 10:38:39,584 disconnect DPU[3:CZZAAR1124] 27/05 10:38:39,600 getJobState 3 from 5b88e DPU[3:CZZAAR1124] 27/05 10:38:39,600 DPU ends DPU[2:CZZAAS1003] 27/05 10:38:39,631 disconnect DPU[2:CZZAAS1003] 27/05 10:38:39,631 DPU ends DPU[4:CZZAAR1125] 27/05 10:38:39,756 >> GetManagerData DPU[4:CZZAAR1125] 27/05 10:38:39,850 >> SetCompInfo DPU[4:CZZAAR1125] 27/05 10:38:39,881 >> GetContainerList DPU[4:CZZAAR1125] 27/05 10:38:39,897 getJobState 3 from 5b8a9 DPU[4:CZZAAR1125] 27/05 10:38:39,897 getJobState 3 from 5b8a9 DPU[4:CZZAAR1125] 27/05 10:38:39,991 >> SetCompAttr DPU[4:CZZAAR1125] 27/05 10:38:40,100 >> SetDetected DPU[4:CZZAAR1125] 27/05 10:38:40,116 disconnect DPU[4:CZZAAR1125] 27/05 10:38:40,116 getJobState 3 from 5b8a9 DPU[4:CZZAAR1125] 27/05 10:38:40,116 DPU ends DM[1] 27/05 10:38:40,741 **AND** 0 Agents triggered JCE[1] 27/05 10:38:42,756 JCE ends DM[1] 27/05 10:38:47,475 **AND** 0 Agents triggered DM[1] 27/05 10:38:54,241 **AND** 0 Agents triggered

  Read the article

• Database-as-a-Service on Exadata Cloud

  - by Gagan Chawla

  Note – Oracle Enterprise Manager 12c DBaaS is platform agnostic and is designed to work on Exadata/non-Exadata, physical/virtual, Oracle/non Oracle platforms and it’s not a mandatory requirement to use Exadata as the base platform. Database-as-a-Service (DBaaS) is an important trend these days and the top business drivers motivating customers towards private database cloud model include constant pressure to reduce IT Costs and Complexity, and also to be able to improve Agility and Quality of Service. The first step many enterprises take in their journey towards cloud computing is to move to a consolidated and standardized environment and Exadata being already a proven best-in-class popular consolidation platform, we are seeing now more and more customers starting to evolve from Exadata based platform into an agile self service driven private database cloud using Oracle Enterprise Manager 12c. Together Exadata Database Machine and Enterprise Manager 12c provides industry’s most comprehensive and integrated solution to transform from a typical silo’ed environment into enterprise class database cloud with self service, rapid elasticity and pay-per-use capabilities.   In today’s post, I’ll list down the important steps to enable DBaaS on Exadata using Enterprise Manager 12c. These steps are chalked down based on a recent DBaaS implementation from a real customer engagement - Project Planning - First step involves defining the scope of implementation, mapping functional requirements and objectives to use cases, defining high availability, network, security requirements, and delivering the project plan. In a Cloud project you plan around technology, business and processes all together so ensure you engage your actual end users and stakeholders early on in the project right from the scoping and planning stage. Setup your EM 12c Cloud Control Site – Once the project plan approval and sign off from stakeholders is achieved, refer to EM 12c Install guide and these are some important tips to follow during the site setup phase - Review the new EM 12c Sizing paper before you get started with install Cloud, Chargeback and Trending, Exadata plug ins should be selected to deploy during install Refer to EM 12c Administrator’s guide for High Availability, Security, Network/Firewall best practices and options Your management and managed infrastructure should not be combined i.e. EM 12c repository should not be hosted on same Exadata where target Database Cloud is to be setup Setup Roles and Users – Cloud Administrator (EM_CLOUD_ADMINISTRATOR), Self Service Administrator (EM_SSA_ADMINISTRATOR), Self Service User (EM_SSA_USER) are the important roles required for cloud lifecycle management. Roles and users are managed by Super Administrator via Setup menu –> Security option. For Self Service/SSA users custom role(s) based on EM_SSA_USER should be created and EM_USER, PUBLIC roles should be revoked during SSA user account creation. Configure Software Library – Cloud Administrator logs in and in this step configures software library via Enterprise menu –> provisioning and patching option and the storage location is OMS shared filesystem. Software Library is the centralized repository that stores all software entities and is often termed as ‘local store’. Setup Self Update – Self Update is one of the most innovative and cool new features in EM 12c framework. Self update can be accessed via Setup -> Extensibility option by Super Administrator and is the unified delivery mechanism to get all new and updated entities (Agent software, plug ins, connectors, gold images, provisioning bundles etc) in EM 12c. Deploy Agents on all Compute nodes, and discover Exadata targets – Refer to Exadata discovery cookbook for detailed walkthrough to ensure successful discovery of Exadata targets. Configure Privilege Delegation Settings – This step involves deployment of privilege setting template on all the nodes by Super Administrator via Setup menu -> Security option with the option to define whether to use sudo or powerbroker for all provisioning and patching operations. Provision Grid Infrastructure with RAC Database on Compute Nodes – Software is provisioned in this step via a provisioning profile using EM 12c database provisioning. In case of Exadata, Grid Infrastructure and RAC Database software is already deployed on compute nodes via OneCommand from Oracle, so SSA Administrator just needs to discover Oracle Homes and Listener as EM targets. Databases will be created as and when users request for databases from cloud. Customize Create Database Deployment Procedure – the actual database creation steps are "templatized" in this step by Self Service Administrator and the newly saved deployment procedure will be used during service template creation in next step. This is an important step and make sure you have locked all the required variables marked as locked as ‘Y’ in this table. Setup Self Service Portal – This step involves setting up of zones, user quotas, service templates, chargeback plan. The SSA portal is setup by Self Service Administrator via Setup menu -> Cloud -> Database option and following guided workflow. Refer to DBaaS cookbook for details. You also have an option to customize SSA login page via steps documented in EM 12c Cloud Administrator’s guide Final Checks – Define and document process guidelines for SSA users and administrators. Get your SSA users trained on Self Service Portal features and overall DBaaS model and SSA administrators should be familiar with Self Service Portal setup pieces, EM 12c database lifecycle management capabilities and overall EM 12c monitoring framework. GO LIVE – Announce rollout of Database-as-a-Service to your SSA users. Users can login to the Self Service Portal and request/monitor/view their databases in Exadata based database cloud. Congratulations! You just delivered a successful database cloud implementation project! In future posts, we will cover these additional useful topics around database cloud – DBaaS Implementation tips and tricks – right from setup to self service to managing the cloud lifecycle ‘How to’ enable real production databases copies in DBaaS with rapid provisioning in database cloud Case study of a customer who recently achieved success with their transformational journey from traditional silo’ed environment on to Exadata based database cloud using Enterprise Manager 12c. More Information – Podcast on Database as a Service using Oracle Enterprise Manager 12c Oracle Enterprise Manager 12c Installation and Administration guide, Cloud Administration guide DBaaS Cookbook Exadata Discovery Cookbook Screenwatch: Private Database Cloud: Set Up the Cloud Self-Service Portal Screenwatch: Private Database Cloud: Use the Cloud Self-Service Portal Stay Connected: Twitter |  Face book |  You Tube |  Linked in |  Newsletter

  Read the article

• Passing Activity to non-activity object properly

  - by rayman

  In my app ive got a non-activity object which it's role is being a manager class. many times i need to pass "source activity" to methods as parameter to that manager class in order to make some operations on that activity. for exaple let's assume we have MyActivity which gotta do some toast. so i have this manager class called MyManager, and i have this method in it raiseToast(Activity sourceActivity) { Toast.makeText(sourceActivity, demo, Toast.LENGTH_LONG).show(); } and from Myactivity class we calling that method this way: MyManager manager=new MyManager(); manager.raitetoast(MyActivity.this); it works fine. what I'm asking here, is this a proper way to pass an Activity as parameter to a non-activity object? I'm having a memory leaks on real device(not the emulator), I wonder if this could also causing any reason for that? Thanks Idan.

  Read the article

• Adding a Network Loopback Adapter to Windows 8

  - by Greg Low

  I have to say that I continue to be frustrated with finding out how to do things in Windows 8. Here's another one and it's recorded so it might help someone else. I've also documented what I tried so that if anyone from the product group ever reads this, they'll understand how I searched for it and might try to make it easier.I wanted to add a network loopback adapter, to have a fixed IP address to work with when using an "internal" network with Hyper-V. (The fact that I even need to do this is also painful. I don't know why Hyper-V can't make it easy to work with host system folders, etc. as easily as I can with VirtualPC, VirtualBox, etc. but that's a topic for another day).In the end, what I needed was a known IP address on the same network that my guest OS was using, via the internal network (which allows connectivity from the host OS to/from guest OS's).I started by looking in the network adapters areas but there is no "add" functionality there. Realising that this was likely to be another unexpected challenge, I resorted to searching for info on doing this. I found KB article 2777200 entitled "Installing the Microsoft Loopback Adapter in Windows 8 and Windows Server 2012". Aha, I thought that's what I'd need. It describes the symptom as "You are trying to install the Microsoft Loopback Adapter, but are unable to find it." and that certainly sounded like me. There's a certain irony in documenting that something's hard to find instead of making it easier to find. Anyway, you'd hope that in that article, they'd then provide a step by step example of how to do it, but what they supply is this: The Microsoft Loopback Adapter was renamed in Windows 8 and Windows Server 2012. The new name is "Microsoft KM-TEST Loopback Adapter". When using the Add Hardware Wizard to manually add a network adapter, choose Manufacturer "Microsoft" and choose network adapter "Microsoft KM-TEST Loopback Adapter".The trick with this of course is finding the "Add Hardware Wizard". In Control Panel -> Hardware and Sound, there are options to "Add a device" and for "Device Manager". I tried the "Add a device" wizard (seemed logical to me) but after that wizard tries it's best, it just tells you that there isn't any hardware that it thinks it needs to install. It offers a link for when you can't find what you're looking for, but that leads to a generic help page that tells you how to do things like turning on your printer.In Device Manager, I checked the options in the program menus, and nothing useful was present. I even tried right-clicking "Network adapters", hoping that would lead to an option to add one, also to no avail.So back to the search engine I went, to try to find out where the "Add Hardware Wizard" is. Turns out I was in the right place in Device Manager, but I needed to right-click the computer's name, and choose "Add Legacy Hardware". No doubt that hasn't changed location lately but it's a while since I needed to add one so I'd forgotten. Regardless, I'm left wondering why it couldn't be in the menu as well.Anyway, for a step by step list, you need to do the following:1. From Control Panel, select "Device Manager" under the "Devices and Printers" section of the "Hardware and Sound" tab.2. Right-click the name of the computer at the top of the tree, and choose "Add Legacy Hardware".3. In the "Welcome to the Add Hardware Wizard" window, click Next.4. In the "The wizard can help you install other hardware" window, choose "Install the hardware that I manually select from a list" option and click Next.5. In the "The wizard did not find any new hardware on your computer" window, click Next.6. In the "From the list below, select the type of hardware you are installing" window, select "Network Adapters" from the list, and click Next.7. In the "Select Network Adapter" window, from the Manufacturer list, choose Microsoft, then in the Network Adapter window, choose "Microsoft KM-TEST Loopback Adapter", then click Next.8. In the "The wizard is ready to install your hardware" window, click Next.9. In the "Completing the Add Hardware Wizard" window, click Finish.Then you need to continue to set the IP address, etc.10. Back in Control Panel, select the "Network and Internet" tab, click "View Network Status and Tasks".11. In the "View your basic network information and set up connections" window, click "Change adapter settings".12. Right-click the new adapter that has been added (find it in the list by checking the device name of "Microsoft KM-TEST Loopback Adapter"), and click Properties.   

  Read the article

• How do I turn on wireless adapter on HP Envy dv6 7200 under Ubuntu (any version)?

  - by Dave B.

  I have a new HP Envy dv6 7200 with dual boot Windows 8 / Ubuntu 12.04. In windows, the F12 key in Windows activates the "airplane mode" switch which enables/disables both on-board (mini PCIe) and USB wireless adapters. In Ubuntu, however, the wireless adapter is turned off by default and cannot be turned back on via the F12 key (or any other combination of F12 and Ctrl, Fn, Shift, etc.). Let me explain the "fixes" I've seen in various forums and explain what did or did not happen. These are listed in no particular order. (Spoiler alert: wireless is still broke). Solution 1? Use HP's "Wireless Assistant" utility to permanently activate the wireless card in Windows, then boot into Ubuntu to happily find it working. Unfortunately, this utility works in Windows 7 but not Windows 8. On the other hand, hardware drivers from HP are only available for Windows 8 for this model. Catch 22 (I could not find a comparable utility for Windows 8). Solution 2? Use a USB wireless adapter to sidestep the on-board device. I purchased such a device from thinkpenguin.com to be sure that it would be Linux-friendly. However, the wireless switch enables / disables all wireless devices including USB. So, there's my $50 donation to the nice folks at thinkpenguin.com, but still no solution. Solution 3? Following the Think Penguin folk's suggestion, modify the mini PCI express adapter following instructions here: http://www.notebookforums.com/t/225429/broken-wireless-hardware-switch-fix Tempting, but I then violate the terms of my warranty mere days after opening the box. This might be a good solution for an older machine that you want to get your geek on with, but not for a new box. Solution 4? rfkill unblock all No effect whatsoever. ubuntu@ubuntu-hp-evny:~$ rfkill unblock all ubuntu@ubuntu-hp-evny:~$ rfkill list all 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Solution 5? Re-install drivers. Done and done. Ubuntu recognizes the device - perhaps even without re-installing the drivers? - but cannot turn it on. How do I know this? In the Network Manager drop-down menu, the wireless option is blacked out and a message reads something like: "wireless network is disabled by a hardware switch". Solution 6? Identify a physical switch on the laptop and flip it. There is no such switch on this machine. In fact, walking through Best Buy yesterday, I checked and not a single new laptop PC had a physical switch on it. All of the wireless switches are either the F2 or F12 key ... I wonder if askubuntu will not be plagued by this exact issue in the near future? Additional info - lspci ubuntu@ubuntu-hp-evny:~$ lspci 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Ivy Bridge PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.2 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 3 (rev c4) 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 4 (rev c4) 00:1c.5 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 6 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 RAID bus controller: Intel Corporation 82801 Mobile SATA Controller [RAID mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation Device 0de9 (rev a1) 08:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device 5229 (rev 01) 0a:00.0 Network controller: Ralink corp. Device 539b 0b:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) Any suggestions would be much appreciated!

  Read the article

• Using accelerometer to detect iPad lock switch trigger?

  - by DevDevDev

  So for complicated reasons I am managing view rotations myself, and am only implementing UIDeviceOrientationPortrait as the autorotating orientation. Anyway, when one clicks the screen lock on the iPad, the device will rotate to UIDeviceOrientationPortrait, which will cause my code to rotate, which I do not want to happen. For instance of the user is holding the device in "landscape mode", i.e. I have already manually rotated the UI to landscape mode, and he/she clicks the screen lock, it will rotate the UI to portrait mode, even though the user did not move the device at all. So somehow I need a way to differentiate between rotations to portrait mode occuring from the screen lock, and those occuring from device rotation. As such, I would like somehow to use the accelerometer to detect whether or not the device was actually 'rotated' or whether the button was clicked. Thanks!

  Read the article

• Windows XP Home Edition SP3 cant recognise PCMIA SD Card

  - by Pozo

  System Specifications: Laptop : Dell Inspiron 6000 OS: Windows Home Edition SP3 SD Adapter: Hagiwara Smart Media Adapter I inserted the card into the slot, windows xp recognises the device, lists the pcmia controller on the device manager list, an entry appears under the IDE ATA/ATAPI category on the device manager as well. However, the device does not show under my computer and the driver does not get assigned a letter number. I checked the system logs from the device manager and there were no logged errors. Checking the Hagiwara support website, the manufacturer indicates that the adapter driver is the same as the windows xp pcmia controller. Checking Dell's website, no specific drivers were listed for that either. General Search on the web indicates that multiple people face similar problems with their SD cards, yet none actually spell out the route issue that causes this. Please let me know if you have any suggestions for further debugging. Thanks in advance

  Read the article

• Specs, Form and Function – What am I Missing?

  - by Barry Shulam

  0 0 1 628 3586 08041 29 8 4206 14.0 Normal 0 false false false EN-US JA X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:12.0pt; font-family:Cambria; mso-ascii-font-family:Cambria; mso-ascii-theme-font:minor-latin; mso-hansi-font-family:Cambria; mso-hansi-theme-font:minor-latin;} Friday October 26th the Microsoft Surface RT arrived at the office.  I was summoned to my boss’s office for the grand unpacking.  If I had planned ahead I could have used my iPhone 4 to film the event and post it on YouTube however the desire to hold the device and turn it ON was more inviting than becoming a proxy reviewer for Engadget’s website.  1980 was the first time we had a personal computer in our house.  It was a  Kaypro computer. It weighed 29 pounds more than any persons lap could hold.  Then the term “portable computer” meant you could remove it from the building and take it else where.  Today I am typing on this entry on a Macbook Air which weighs 2.38 pounds. This morning Amazons front page main title is: “Much More for Much Less” I was born at the right time to start with the CPM operating system on the Kaypro thru the DOS, Windows, Linux, Mac OSX and mobile phone operating systems and languages.  If you are not aware Technology is moving at a rapid pace.  The New iPad (those who are keeping score – iPad4) is replacing a 7 month old machine the New iPad (iPad 3) I have used and owned many technology devices in my life.  The main point that most of the reader who are in the USA overlook is the fact that we are in the USA.  The devices we purchase have a great digital garden to support them.  The Kaypro computer had a 7-inch screen.  It was a TV tube with two colors – Black and Green.  You could see the 80-column screen flicker with characters – have you every played Pac-Man emulated on the screen with the ABC characters. Traveling across the world you will find that not all apps on your device will function as they did back home because they are not offered outside of your country of origin. I think the main question a buyer of technology should be asking is Function.  The greatest Specs with out function limit you.  The most beautiful form with out function is the same as a crystal vase on your shelf – not a good cereal bowl in the morning. Microsoft Surface RT, Amazon Kindle Fire and Apple iPad all great devices in their respective customers hands. My advice for those looking to purchase on this year:  If the device is your only technology device you buy what you WANT and LIKE. Consider this parallel universe if its not your only device?  Ever go shopping for clothing, shoes, and accessories with your wife, girlfriend, sister or mother?  If you listen carefully you will hear the little voices coming out of there heads saying:  “This goes well with that and I can use it also with that outfit” ”Do you think this clashes with that?”  “Ohh I love how that combination looks on you”.  Portable devices such as tablets and computers can offer a whole lot more when they are combined with the digital echo system you have at home and the manufacturer offers online. Pros of each Device: Microsoft Surface RT: There is a new functionality named SmartGlass which will let you share the content off your tablet to your XBOX 360.  Microsoft office is loaded on the tablet.  You can have more than one user profile on the tablet if you share it with others.   Amazon Kindle or Kindle HD: If you are an Amazon consumer with an annual Amazon Prime service you can consume videos and read books off the Amazon site.  Its the cheapest device.  Its a step up from the kindle reader in many ways.   Apple Ipad or Ipad mini: Over 270 Thousand applications.  Airplay permits you the ability to share to your TV screen. If you are a cord cutter (a person who gets their entertainment content over the web or air vs Cable Providers) the Airplay or Smart glass are a huge bonus.  iPad mini or not: The mini will fit in a purse where the larger one will not.  Its lighter which makes it nice to hold for prolonged periods.  It has an option for LTE wireless which non of the other sub 9 inch tables offer.  The screen is non retina which means the applications are smaller.  Speaking with individuals who are above 50 in age that wear glasses they retina does not make a difference for them however they prefer the larger iPad over the new mini.   Happy Shopping this Channuka Season.   The Kosher Coder.   Follow me on twitter @KosherCoder

  Read the article

• Best Practices - Dynamic Reconfiguration

  - by jsavit

  This post is one of a series of "best practices" notes for Oracle VM Server for SPARC (formerly named Logical Domains) Overview of dynamic Reconfiguration Oracle VM Server for SPARC supports Dynamic Reconfiguration (DR), making it possible to add or remove resources to or from a domain (virtual machine) while it is running. This is extremely useful because resources can be shifted to or from virtual machines in response to load conditions without having to reboot or interrupt running applications. For example, if an application requires more CPU capacity, you can add CPUs to improve performance, and remove them when they are no longer needed. You can use even use Dynamic Resource Management (DRM) policies that automatically add and remove CPUs to domains based on load. How it works (in broad general terms) Dynamic Reconfiguration is done in coordination with Solaris, which recognises a hypervisor request to change its virtual machine configuration and responds appropriately. In essence, Solaris receives a message saying "you now have 16 more CPUs numbered 16 to 31" or "8GB more RAM starting at address X" or "here's a new network or disk device - have fun with it". These actions take very little time. Solaris then can start using the new resource. In the case of added CPUs, that means dispatching processes and potentially binding interrupts to the new CPUs. For memory, Solaris adds the new memory pages to its "free" list and starts using them. Comparable actions occur with network and disk devices: they are recognised by Solaris and then used. Removing is the reverse process: after receiving the DR message to free specific CPUs, Solaris unbinds interrupts assigned to the CPUs and stops dispatching process threads. That takes very little time. primary # ldm list NAME STATE FLAGS CONS VCPU MEMORY UTIL UPTIME primary active -n-cv- SP 16 4G 1.0% 6d 22h 29m ldom1 active -n---- 5000 16 8G 0.9% 6h 59m primary # ldm set-core 5 ldom1 primary # ldm list NAME STATE FLAGS CONS VCPU MEMORY UTIL UPTIME primary active -n-cv- SP 16 4G 0.2% 6d 22h 29m ldom1 active -n---- 5000 40 8G 0.1% 6h 59m primary # ldm set-core 2 ldom1 primary # ldm list NAME STATE FLAGS CONS VCPU MEMORY UTIL UPTIME primary active -n-cv- SP 16 4G 1.0% 6d 22h 29m ldom1 active -n---- 5000 16 8G 0.9% 6h 59m Memory pages are vacated by copying their contents to other memory locations and wiping them clean. Solaris may have to swap memory contents to disk if the remaining RAM isn't enough to hold all the contents. For this reason, deallocating memory can take longer on a loaded system. Even on a lightly loaded system it took several 7 or 8 seconds to switch the domain below between 8GB and 24GB of RAM. primary # ldm set-mem 24g ldom1 primary # ldm list NAME STATE FLAGS CONS VCPU MEMORY UTIL UPTIME primary active -n-cv- SP 16 4G 0.1% 6d 22h 36m ldom1 active -n---- 5000 16 24G 0.2% 7h 6m primary # ldm set-mem 8g ldom1 primary # ldm list NAME STATE FLAGS CONS VCPU MEMORY UTIL UPTIME primary active -n-cv- SP 16 4G 0.7% 6d 22h 37m ldom1 active -n---- 5000 16 8G 0.3% 7h 7m What if the device is in use? (this is the anecdote that inspired this blog post) If CPU or memory is being removed, releasing it pretty straightforward, using the method described above. The resources are released, and Solaris continues with less capacity. It's not as simple with a network or I/O device: you don't want to yank a device out from underneath an application that might be using it. In the following example, I've added a virtual network device to ldom1 and want to take it away, even though it's been plumbed. primary # ldm rm-vnet vnet19 ldom1 Guest LDom returned the following reason for failing the operation: Resource Information ---------------------------------------------------------- ----------------------- /devices/virtual-devices@100/channel-devices@200/network@1 Network interface net1 VIO operation failed because device is being used in LDom ldom1 Failed to remove VNET instance That's what I call a helpful error message - telling me exactly what was wrong. In this case the problem is easily solved. I know this NIC is seen in the guest as net1 so: ldom1 # ifconfig net1 down unplumb Now I can dispose of it, and even the virtual switch I had created for it: primary # ldm rm-vnet vnet19 ldom1 primary # ldm rm-vsw primary-vsw9 If I had to take away the device disruptively, I could have used ldm rm-vnet -f but that could disrupt whoever was using it. It's better if that can be avoided. Summary Oracle VM Server for SPARC provides dynamic reconfiguration, which lets you modify a guest domain's CPU, memory and I/O configuration on the fly without reboot. You can add and remove resources as needed, and even automate this for CPUs by setting up resource policies. Taking things away can be more complicated than giving, especially for devices like disks and networks that may contain application and system state or be involved in a transaction. LDoms and Solaris cooperative work together to coordinate resource allocation and de-allocation in a safe and effective way. For best practices, use dynamic reconfiguration to make the best use of your system's resources.

  Read the article

• How do I rotate my monitor using xorg?

  - by user1106405

  I have just installed KUbuntu 12.10, and I am attempting to rotate my monitor 90 deg to the left. When I add the option to rotate, the monitor seems to ignore the directive. I'm currently using dual 02:00.0 VGA compatible controller: NVIDIA Corporation GF104 [GeForce GTX 460] (rev a1) 03:00.0 VGA compatible controller: NVIDIA Corporation GF104 [GeForce GTX 460] (rev a1) and NVidia driver version 310 My xorg.conf is as follows: # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 304.51 (buildd@komainu) Fri Oct 12 12:53:49 UTC 2012 # nvidia-xconfig: X configuration file generated by nvidia-xconfig # nvidia-xconfig: version 310.14 ([email protected]) Tue Oct 9 13:04:01 PDT 2012 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" 1280 0 Screen 1 "Screen1" RightOf "Screen0" Screen 2 "Screen2" 0 0 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "1" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "Samsung SyncMaster" HorizSync 30.0 - 81.0 VertRefresh 56.0 - 60.0 Option "DPMS" EndSection Section "Monitor" Identifier "Monitor1" VendorName "Unknown" ModelName "DELL 1908WFP" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 75.0 EndSection Section "Monitor" Identifier "Monitor2" VendorName "Unknown" ModelName "DELL 1907FP" HorizSync 30.0 - 81.0 VertRefresh 56.0 - 76.0 EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GTX 460" BusID "PCI:2:0:0" Screen 0 EndSection Section "Device" Identifier "Device1" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GTX 460" BusID "PCI:2:0:0" Screen 1 EndSection Section "Device" Identifier "Device2" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GTX 460" BusID "PCI:3:0:0" EndSection Section "Screen" # Removed Option "metamodes" "DFP-0: nvidia-auto-select +0+0; DFP-0: nvidia-auto-select +0+0; DFP-0: 1920x1200 +0+0; DFP-0: 1920x1200_60 +0+0; DFP-0: 1600x1200 +0+0; DFP-0: 1600x1200_60 +0+0; DFP-0: 1280x1024 +0+0; DFP-0: 1280x1024_60 +0+0; DFP-0: 1280x960 +0+0; DFP-0: 1280x960_60 +0+0; DFP-0: 1024x768 +0+0; DFP-0: 1024x768_60 +0+0; DFP-0: 800x600 +0+0; DFP-0: 800x600_60 +0+0; DFP-0: 800x600_56 +0+0; DFP-0: 640x480 +0+0; DFP-0: 640x480_60 +0+0; DFP-0: nvidia-auto-select @1920x1080 +0+0; DFP-0: nvidia-auto-select @1920x720 +0+0" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "Stereo" "0" Option "metamodes" "DFP-0: nvidia-auto-select +0+0; DFP-0: nvidia-auto-select +0+0; DFP-0: 1920x1200 +0+0; DFP-0: 1920x1200_60 +0+0; DFP-0: 1600x1200 +0+0; DFP-0: 1600x1200_60 +0+0; DFP-0: 1280x1024 +0+0; DFP-0: 1280x1024_60 +0+0; DFP-0: 1280x960 +0+0; DFP-0: 1280x960_60 +0+0; DFP-0: 1024x768 +0+0; DFP-0: 1024x768_60 +0+0; DFP-0: 800x600 +0+0; DFP-0: 800x600_60 +0+0; DFP-0: 800x600_56 +0+0; DFP-0: 640x480 +0+0; DFP-0: 640x480_60 +0+0; DFP-0: nvidia-auto-select +0+0; DFP-0: nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 Option "Stereo" "0" Option "metamodes" "DFP-2: nvidia-auto-select +0+0" Option "Rotate" "left" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen2" Device "Device2" Monitor "Monitor2" DefaultDepth 24 Option "Stereo" "0" Option "metamodes" "nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Extensions" Option "Composite" "Enable" EndSection Edit: If I delete the xorg.conf and reboot, I am able to rotate my monitor, however, my third monitor is not recognized: Screen 0: minimum 8 x 8, current 3360 x 1200, maximum 16384 x 16384 DVI-I-0 disconnected (normal left inverted right x axis y axis) DVI-I-1 disconnected (normal left inverted right x axis y axis) DVI-I-2 connected 1920x1200+0+0 (normal left inverted right x axis y axis) 518mm x 324mm 1920x1200 60.0*+ 1600x1200 60.0 1280x1024 60.0 1280x960 60.0 1024x768 60.0 800x600 60.3 56.2 640x480 59.9 HDMI-0 disconnected (normal left inverted right x axis y axis) DVI-I-3 connected 1440x900+1920+0 (normal left inverted right x axis y axis) 408mm x 255mm 1440x900 59.9*+ 75.0 1280x1024 75.0 60.0 1280x800 59.8 1152x864 75.0 1024x768 75.0 70.1 60.0 800x600 75.0 72.2 60.3 56.2 640x480 75.0 72.8 59.9

  Read the article

• Tab widget example not running

  - by michbeck

  I'm trying to reproduce the tabwidget example (http://developer.android.com/resources/tutorials/views/hello-tabwidget.html). I'm not really sure what's the problem, I got no errors while compiling, but i cannot see the application on the emulators screen. It would be excellent if maybe anyone could have a look at my classes and tell me what's my mistake? I've packed my project here: http://etanto.com/TabTest.zip here's the console dump while the run: [2010-06-10 09:18:34 - TabTest] Launching a new emulator with Virtual Device 'Virtual1' [2010-06-10 09:18:35 - TabTest] New emulator found: emulator-5554 [2010-06-10 09:18:35 - TabTest] Waiting for HOME ('android.process.acore') to be launched... [2010-06-10 09:19:05 - TabTest] WARNING: Application does not specify an API level requirement! [2010-06-10 09:19:05 - TabTest] Device API version is 8 (Android 2.2) [2010-06-10 09:19:05 - TabTest] HOME is up on device 'emulator-5554' [2010-06-10 09:19:05 - TabTest] Uploading TabTest.apk onto device 'emulator-5554' [2010-06-10 09:19:05 - TabTest] Installing TabTest.apk... [2010-06-10 09:19:22 - TabTest] Success! [2010-06-10 09:19:22 - TabTest] \TabTest\bin\TabTest.apk installed on device [2010-06-10 09:19:22 - TabTest] Done!

  Read the article

• Installing app on Devices(iPhone/iPod)

  - by Shakti

  Hi, I have developed an application for iPhone and iPod touch. Now i want to install that app on the device. I have created a provisioning profile for the particular device. My query is that, now to install the app on a device I have to add the provisioning profile of that device to xcode and after selecting the developer in build option in project info pane i build the project and send the build and provisioning profile to the user. Is there any to install the app without doing the above task of building the project with the provisioning profile. Means i have a build of an app and a newly downloaded provisioning profile. I will send the user both build and profile in a zip file. will the user be able to install the app on his/her device?

  Read the article

• UIWebView goBack method acts differently on different devices

  - by maxpower

  First Device: 8gb 2nd gen Version: 3.1.3 (7E18) Model: MB528LL Second Device: 32gb 3rd gen Version: 3.1.3 (7E18) Model: MC008LL When I call goBack on the 8gb device, shouldStartLoadWithRequest:navigationType: is called When I call goBack on the 32gb device, shouldStartLoadWithRequest:navigationType: is not called I am not doing any caching (not like it works anyway). To make sure it wasn't caching I removed any possible caching via the request object's cache policy and removing all cache whenever webViewDidFinishLoading is called. Same app, same url, everything is the same but the device itself. Why? FYI: shouldStartLoadWithRequest:navigationType: is called on the simulator when goBack is called

  Read the article

• JDO Exception in google app engine transaction

  - by Mariselvam

  I am getting the following exception while trying to use transation in app engine datastore. javax.jdo.JDOUserException: Transaction is still active. You should always close your transactions correctly using commit() or rollback(). FailedObject:org.datanucleus.store.appengine.jdo.DatastoreJDOPersistenceManager@12bbe6b at org.datanucleus.jdo.JDOPersistenceManager.close(JDOPersistenceManager.java:277) The following is the code snippet I used : List<String> friendIds = getFriends(userId); Date currentDate = new Date(); PersistenceManager manager = pmfInstance.getPersistenceManager(); try { Transaction trans = manager.currentTransaction(); trans.begin(); for(String friendId : friendIds) { User user = manager.getObjectById(User.class, friendId); if(user != null) { user.setRecoCount(user.getRecoCount() + 1); user.setUpdatedDate(currentDate); manager.makePersistent(user); } } trans.commit(); } finally { manager.close(); }

  Read the article

• Noob tab widget example not running

  - by michbeck

  hey all, i'm trying to reproduce the tabwidget example (http://developer.android.com/resources/tutorials/views/hello-tabwidget.html). i'm not really sure what's the problem, i've git no errors while compiling, but i cannot see the application on emulators screen :-/ would be excellent if maybe anyone could have a look at my classes and tell me what's my mistake? I've packed my project here: http://etanto.com/TabTest.zip thanx a lot in advance, folks! michbeck here's the console dump while the run: [2010-06-10 09:18:34 - TabTest] Launching a new emulator with Virtual Device 'Virtual1' [2010-06-10 09:18:35 - TabTest] New emulator found: emulator-5554 [2010-06-10 09:18:35 - TabTest] Waiting for HOME ('android.process.acore') to be launched... [2010-06-10 09:19:05 - TabTest] WARNING: Application does not specify an API level requirement! [2010-06-10 09:19:05 - TabTest] Device API version is 8 (Android 2.2) [2010-06-10 09:19:05 - TabTest] HOME is up on device 'emulator-5554' [2010-06-10 09:19:05 - TabTest] Uploading TabTest.apk onto device 'emulator-5554' [2010-06-10 09:19:05 - TabTest] Installing TabTest.apk... [2010-06-10 09:19:22 - TabTest] Success! [2010-06-10 09:19:22 - TabTest] \TabTest\bin\TabTest.apk installed on device [2010-06-10 09:19:22 - TabTest] Done!

  Read the article

• crtmqm give no response

  - by Willy

  Hi all, I try to create a WebSphere queue manager in production env. Before this I manage to create the queue manager in the development env with no problem. I'm using this script to create the queue manager: crtmqm -u SYSTEM.DEAD.LETTER.QUEUE test1.qm But it give no response (no error or success message). When I try to start the queue manager (strmqm test1.qm) it give "AMQ8118: WebSphere MQ queue manager does not exist." Then I notice lots of strange thing that supposed not happen: I can run the "crtmqm -u SYSTEM.DEAD.LETTER.QUEUE test1.qm" several times without any error I can just type crtmqm and got no response I can type crtmqm -y (which is not possible since there is no -y argument) and still no response Can anyone tell me what is wrong?

  Read the article

• Multiple column Union Query without duplicates

  - by Adam Halegua

  I'm trying to write a Union Query with multiple columns from two different talbes (duh), but for some reason the second column of the second Select statement isn't showing up in the output. I don't know if that painted the picture properly but here is my code: Select empno, job From EMP Where job = 'MANAGER' Union Select empno, empstate From EMPADDRESS Where empstate = 'NY' Order By empno The output looks like: EMPNO JOB 4600 NY 5300 MANAGER 5300 NY 7566 MANAGER 7698 MANAGER 7782 MANAGER 7782 NY 7934 NY 9873 NY Instead of 5300 and 7782 appearing twice, I thought empstate would appear next to job in the output. For all other empno's I thought the values in the fields would be (null). Am I not understanding Unions correctly, or is this how they are supposed to work? Thanks for any help in advance.

  Read the article

• Not able to run my first program on anroid tablet

  - by misguided

  I am not able to run on my android tablet. I have been following the Android training link It says To run the app from Eclipse: Open one of your project's files and click Run from the toolbar. In the Run as window that appears, select Android Application and click OK. But when I do the same , I do not see anything on my Mototola xoom Tablet. I have checke dthe following link for Setting up USB drivers.As per the link , I have confirmed that device is connected When plugged in over USB, you can verify that your device is connected by executing adb devices from your SDK platform-tools/ directory. If connected, you'll see the device name listed as a "device." C:\Android\sdk\platform-tools>adb devices List of devices attached 0380610842bf5157 device Can anyone please advise where I am going wrong. What should I do to make my eclipse code run on android tablet.

  Read the article

• Select multiple unique lines in MySQL

  - by MartinW

  Hi, I've got a table with the following columns: ID, sysid, x, y, z, timereceived ID is a unique number for each row. sysid is an ID number for a specific device (about 100 different of these) x, y and z is data received from the device. (totally random numbers) timereceived is a timestamp for when the data was received. I need a SQL query to show me the last inserted row for device a, device b, device c and so on. I've been playing around with a lot of different Select statements, but never got anything that works. I manage to get unique rows by using group by, but the rest of the information is random (or at least it feels very random). Anyone able to help me? There could be hundreds of thousands records in this table.

  Read the article

• BizTalk and IBM WebSphere MQ Errors

  - by Christopher House

  The project I'm currently working on is going to make heavy use of IBM WebShere MQ to send messages from BizTalk to the client's iSeries box.  I'd never previously worked with WebSphere MQ, so I didn't really have any idea what it would take to get this to work.  I was pleasantly surprised that it wasn't too difficult to configure a send port and pass messages through it to a queue.  Or so I thought... A couple of weeks ago, the client gave me the name of a host, queue manager and queue that I'd been using for my development.  Everything was going great, I was able to put messages onto the queue, I was happy, the client was happy.  Life was good.  Then the client tells me that the host I've been connecting to is actually a Solaris box and that in prod, we'll actually be sending to an iSeries.  We both agree that it would behoove us to start pointing my dev environment to their dev iSeries box in order to flush out any weirdness there might be.  As it turns out, it was a good thing we made the change.  As soon as I reconfigured my BRE policy that sets endpoint information to point to the iSeries queue, we started seeing failures in the event log.  An example from the event log: Event Type: Error Event Source: BizTalk Server 2009 Event Category: BizTalk Server 2009 Event ID: 5754 Date:  6/9/2010 Time:  10:16:41 AM User:  N/A Computer: WINDOWS2003 Description: A message sent to adapter "MQSC" on send port "<my dynamic sendport name>" with URI "mqsc://client/tcp/<hostname>(1414)/<queue manager name>/<queue name>" is suspended.  Error details: Failure encountered while attempting to open queue. queue = <queue name> queueManager = <queue manager name>, reasonCode = 6124  MessageId:  {76825C7C-611A-4A56-8A6F-35E1124BDB5C}  InstanceID: {BA389103-DF9B-493F-8C61-44574822AAD6} The key piece of information in the event entry is the reasonCode, 6124.  A quick Google search shows that reasonCode 6124 is the code for MQRC_NOT_CONNECTED.  According to IBM's docs, this means that you've tried to send a message without first opening a connection to the queue manager.  Obviously, in the context of BizTalk, this is an unexpected error, since this sort of thing should be managed entirely by the send adapter. Perusing IBM's documentation a bit more, I came across some info on how to turn on tracing for MQ.  With tracing enabled, I tried sending a message again, then went and reviewed the trace files.  The bulk of the information in the trace files didn't mean a thing to me, but at the end of one of the files, I did notice this: 00006257 15:40:20.327795   3500.4      RSESS:000009 ------{  reqReleaseConn 00006258 15:40:20.328714   3500.4      RSESS:000009 ------}  reqReleaseConn (rc=OK) 00006259 15:40:20.328727   3500.4      RSESS:000009 ------{  xcsClearTraceIdent 0000625A 15:40:20.328739   3500.4           :       ------}  xcsClearTraceIdent (rc=OK) 0000625B 15:40:20.328752   3500.4           :       -----}! trmzstMQCONNX (rc=MQRC_NOT_AUTHORIZED) 0000625C 15:40:20.328765   3500.4           :       ----}! MQCONNX (rc=MQRC_NOT_AUTHORIZED) 0000625D 15:40:20.328766   3500.4           :       ---}! ImqQueueManager::connect (rc=MQRC_NOT_AUTHORIZED) 0000625E 15:40:20.328767   3500.4           :       --}! ImqObject::open (rc=MQRC_NOT_CONNECTED) 0000625F 15:40:20.328768   3500.4           :       --{  ImqQueue::lock 00006260 15:40:20.328769   3500.4           :       --}! ImqQueue::lock (rc=Unknown(1)) 00006261 15:40:20.328769   3500.4           :       --{  ImqQueue::unlock 00006262 15:40:20.328769   3500.4           :       --}! ImqQueue::unlock (rc=Unknown(1)) It seemed like the MQRC_NOT_CONNECTED error was being caused by a security related issue (MQRC_NOT_AUTHORIZED).  I did notice something earlier in the log where it appeared that MQ was passing a field named UID with a value equal to the account name that my BizTalk service was running under.  I ended up creating a new local account on the BizTalk server that had the same name as a user which had access to the queue manager on the iSeries.  I then created a new host instance that ran under this new account, created a send handler for the MQSC adapter on this new host instance and reconfigured my orchestration to run on the new host instance.  After bouncing all my host instances, I was now able to send messages to the iSeries. It's still not clear to me why we were able to connect to the Solaris server.  I ended up contacting IBM's support and they did confirm that the process sending to MQ does in fact pass the identity to the queue manager it's connecting to.

  Read the article

• SQLAuthority News – Guest Post – Performance Counters Gathering using Powershell

  - by pinaldave

  Laerte Junior Laerte Junior has previously helped me personally to resolve the issue with Powershell installation on my computer. He did awesome job to help. He has send this another wonderful article regarding performance counter for readers of this blog. I really liked it and I expect all of you who are Powershell geeks, you will like the same as well. As a good DBA, you know that our social life is restricted to a few movies over the year and, when possible, a pizza in a restaurant next to your company’s place, of course. So what we have to do is to create methods through which we can facilitate our daily processes to go home early, and eventually have a nice time with our family (and not sleeping on the couch). As a consultant or fixed employee, one of our daily tasks is to monitor performance counters using Perfmom. To be honest, IDE is getting more complicated. To deal with this, I thought a solution using Powershell. Yes, with some lines of Powershell, you can configure which counters to use. And with one more line, you can already start collecting data. Let’s see one scenario: You are a consultant who has several clients and has just closed another project in troubleshooting an SQL Server environment. You are to use Perfmom to collect data from the server and you already have its XML configuration files made with the counters that you will be using- a file for memory bottleneck f, one for CPU, etc. With one Powershell command line for each XML file, you start collecting. The output of such a TXT file collection is set to up in an SQL Server. With two lines of command for each XML, you make the whole process of data collection. Creating an XML configuration File to Memory Counters: Get-PerfCounterCategory -CategoryName "Memory" | Get-PerfCounterInstance  | Get-PerfCounterCounters |Save-ConfigPerfCounter -PathConfigFile "c:\temp\ConfigfileMemory.xml" -newfile Creating an XML Configuration File to Buffer Manager, counters Page lookups/sec, Page reads/sec, Page writes/sec, Page life expectancy: Get-PerfCounterCategory -CategoryName "SQLServer:Buffer Manager" | Get-PerfCounterInstance | Get-PerfCounterCounters -CounterName "Page*" | Save-ConfigPerfCounter -PathConfigFile "c:\temp\BufferManager.xml" –NewFile Then you start the collection: Set-CollectPerfCounter -DateTimeStart "05/24/2010 08:00:00" -DateTimeEnd "05/24/2010 22:00:00" -Interval 10 -PathConfigFile c:\temp\ConfigfileMemory.xml -PathOutputFile c:\temp\ConfigfileMemory.txt To let the Buffer Manager collect, you need one more counters, including the Buffer cache hit ratio. Just add a new counter to BufferManager.xml, omitting the new file parameter Get-PerfCounterCategory -CategoryName "SQLServer:Buffer Manager" | Get-PerfCounterInstance | Get-PerfCounterCounters -CounterName "Buffer cache hit ratio" | Save-ConfigPerfCounter -PathConfigFile "c:\temp\BufferManager.xml" And start the collection: Set-CollectPerfCounter -DateTimeStart "05/24/2010 08:00:00" -DateTimeEnd "05/24/2010 22:00:00" -Interval 10 -PathConfigFile c:\temp\BufferManager.xml -PathOutputFile c:\temp\BufferManager.txt You do not know which counters are in the Category Buffer Manager? Simple! Get-PerfCounterCategory -CategoryName "SQLServer:Buffer Manager" | Get-PerfCounterInstance | Get-PerfCounterCounters Let’s see one output file as shown below. It is ready to bulk insert into the SQL Server. As you can see, Powershell makes this process incredibly easy and fast. Do you want to see more examples? Visit my blog at Shell Your Experience You can find more about Laerte Junior over here: www.laertejuniordba.spaces.live.com www.simple-talk.com/author/laerte-junior www.twitter.com/laertejuniordba SQL Server Powershell Extension Team: http://sqlpsx.codeplex.com/ Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: SQL, SQL Add-On, SQL Authority, SQL Performance, SQL Query, SQL Server, SQL Tips and Tricks, SQL Utility, T SQL, Technology Tagged: Powershell

  Read the article

< Previous Page | 144 145 146 147 148 149 150 151 152 153 154 155  | Next Page >