Search Results

Search found 16902 results on 677 pages for 'trade off'.

Page 148/677 | < Previous Page | 144 145 146 147 148 149 150 151 152 153 154 155  | Next Page >

• Some URLs fail to load on Windows web portal

  - by jpolache

  I’m working in a large data center and have been assigned to troubleshoot and issue with a windows (IIS) web server that acts as a portal for a customer of the data center. This portal server is on a DMZ at the local data center. I don’t have access to the portal desktop and am relying on an off-site administrator to work with me to do testing and report the condition of the portal. He tells me there are no software firewalls or other filtering configured. While most of the remote web pages work fine, several of the URSs the portal is suppose to serve up fail to load. I had wireshark installed on the portal system and had a capture taken of one of the failures. I used IE to access one of the remote web servers at issue. I could see the TCP SYN-ACK coming back from the remote server, but after several HTTP GETs fail to get a response the portal server sends a reset. The webmaster of the remote web server assures me that no sites are being blocked. I had a capture taken outside the local firewall, so there should be no issue there. Another tech set up a laptop and used the IP address of the portal (we took the portal off-line for the test). The laptop loads the URL as expected. I tried having Firefox loaded to make sure that the HTTP GET was not mal-formed. Same failure as with IE. So, it seems it is not the remote web server or the network, because there was no problem with the laptop. At this point, I’m not sure what other questions to ask or tests to do.

  Read the article

• How can adding a server to a domain cause Remote Desktop to stop working?

  - by Adrian Grigore

  I have two dedicated with Windows 2008 R2 servers which I am using for Web hosting. One Server A is a domain controller, Server B should simply be added to the domain controlled by Server A. So I RDP'd into Server B and changed the system settings so that Server B is part of that domain. I entered my domain admin credentials, was welcomed to the domain and asked to reboot the server. So far everything seemed to work smoothly After rebooting, I could not open an RDP connection to Server B anymore: Remote Desktop can’t connect to the remote computer for one of these reasons: 1) Remote access to the server is not enabled 2) The remote computer is turned off 3) The remote computer is not available on the network Make sure the remote computer is turned on and connected to the network, and that remote access is enabled. I restored an older backup of Server B and switched off the firewall before adding the server to my domain. But the problem reoccurred just the same. What could be the reason for this? The domain is brandnew and I did not change any of the default settings. Could this be some kind of domain-wide default policy that shuts down RDP on any domain clients? Or perhaps it has to do with the fact that Server B is virtual? Thanks for your help, Adrian

  Read the article

• Rsync when run in cron doesnt work. Rsync between Mac Os x Server and Linux Centos

  - by Brady

  I have a working rsync setup between Mac OS X Server and Linux Centos when run manually in a terminal. I enter the rsync command, it asks for the password, I enter it and off it goes, runs and completes. Now I know thats working I set out to fully automate it via cron. First off I create an SSH authorized key by running this command on the Mac server: ssh-keygen -t dsa -b 1024 -f /Users/admin/Documents/Backup/rsync-key Entering the password and then confirming it. I then copy the rsync-key.pub file accross to the linux server and place in the rsync user .ssh folder and rename to authorized_keys: /home/philosophy/.ssh/authorized_keys I then make sure that the authorized_keys file is chmod 600 in the folder chmod 700. I then setup a shell script for cron to run: #!/bin/bash RSYNC=/usr/bin/rsync SSH=/usr/bin/ssh KEY=/Users/admin/Documents/Backup/rsync-key RUSER=philosophy RHOST=example.com RPATH=data/ LPATH="/Volumes/G Technology G Speed eS/Backup" $RSYNC -avz --delete --progress -e "$SSH -i $KEY" "$LPATH" $RUSER@$RHOST:$RPATH Then give the shell file execute permissions and then add the following to the crontab using crontab -e: 29 12 * * * /Users/admin/Documents/Backup/backup.sh I check my crontab log file after the above command should run and I get this in the log and nothing else: Feb 21 12:29:00 fileserver /usr/sbin/cron[80598]: (admin) CMD (/Users/admin/Documents/Backup/backup.sh) So I asume everything has run as it should. But when I check the remote server no files have been copied accross. If I run the backup.sh file in a terminal as normal it still prompts for a password but this time its through the Mac Key chain system rather than typing into the console window. With the Mac Key Chain I can set it to save the password so that it doesnt ask for it again but Im sure when run with cron this password isnt picked up. This is where I'm asuming where rsync in cron is failing because it needs a password to connect but I thought the whole idea of making the SSH keys was to prevent the use of a password. Have I missed a step or done something wrong here? Thanks Scott

  Read the article

• What are useful .screenrc settings?

  - by gyaresu

  Basically like some of my own that I've posted below. I'm looking for added functionality to the programme 'screen'. At the very least have a look at the last line for a fantastic 'menu bar' at the bottom of a screen session. ## gyaresu's .screenrc 2008-03-25 # http://delicious.com/search?p=screenrc # Don't display the copyright page startup_message off # tab-completion flash in heading bar vbell off # keep scrollback n lines defscrollback 1000 # Doesn't fix scrollback problem on xterm because if you scroll back # all you see is the other terminals history. # termcapinfo xterm|xterms|xs|rxvt ti@:te@ # These will let you use bind -c selectHighs 0 select 10 #these three commands are bind -c selectHighs 1 select 11 #added to the command-class bind -c selectHighs 2 select 12 #selectHighs bind -c selectHighs 3 select 13 bind -c selectHighs 4 select 14 bind -c selectHighs 5 select 15 bind - command -c selectHighs #bind the hyphen to #command-class selectHighs screen -t rtorrent 0 rtorrent #screen -t tunes 1 ncmpc --host=192.168.1.4 --port=6600 #was for connecting to MPD music server. screen -t stuff 1 screen -t irssi 2 irssi screen -t dancing 4 screen -t python 5 python screen -t giantfriend 6 these_are_ssh_to_server_scripts.sh screen -t computerrescue 7 these_are_ssh_to_server_scripts.sh screen -t BMon 8 bmon -p eth0 screen -t htop 9 htop screen -t hellanzb 10 hellanzb screen -t watching 3 #screen -t interactive.fiction 8 #screen -t hellahella 8 paster serve --daemon /home/gyaresu/downloads/hellahella/hella.ini shelltitle "$ |bash" # THIS IS THE PRETTY BIT #change the hardstatus settings to give an window list at the bottom of the ##screen, with the time and date and with the current window highlighted hardstatus alwayslastline #hardstatus string '%{= mK}%-Lw%{= KW}%50>%n%f* %t%{= mK}%+Lw%< %{= kG}%-=%D %d %M %Y %c:%s%{-}' hardstatus string '%{= kG}[ %{G}%H %{g}][%= %{= kw}%?%-Lw%?%{r}(%{W}%n*%f%t%?(%u)%?%{r})%{w}%?%+Lw%?%?%= %{g}][%{B} %d/%m %{W}%c %{g}]'

  Read the article

• Webmin ADSL module

  - by expatcm

  I was wondering if the Webmin ADSL module is going to help me solve a problem .... but I cannot find any documentation telling me what the module does ..... Any ideas? What I am hoping is that it will solve a problem .... I am just in the process of setting up a Debian server. I will use the DHCP server as part of the Debian setup to manage the lan IP addresses. I want to turn off the external DHCP server which is part of the Linksys ADSL modem / router and use just the modem. The challenge I have is knowing what I need to do in order to get the public DNS on the eth1. When I turn off the DHCP on the modem / router not a lot happens apart from no longer being able to access the settings .......... So I am looking at this Webmin module and wondering if it is to manage the ADSL connection and find the public DNS address .... The local DHCP server is working well for the lan, I am just stuck for the external DNS.

  Read the article

• Use one NIC to create multiple interfaces for Linux KVM

  - by Phanto

  I am working on a thesis research project, and I am having some difficulty figuring out how to make one NIC spawn several "bridge" interfaces such that each KVM VM can be seen on the local network. I am very new to KVM, and am still exploring what it can do. Below is the scenario that I am attempting to make (on a CentOS/RHEL 6 system): Linux KVM Host has 1 NIC (eth0) connected to a switch. Create multiple "bridge" or equivalent interfaces that are spawned off of eth0 that would provide a unique IP for each VM. This is so that each VM can communicate with other hosts on the network, and that other hosts on the network can communicate with the VM. IMPORTANT: I would like iptables on the KVM host to be able to manipulate/control/restrict the traffic that would be sent on those "bridge" interfaces. I would like to create a minimum of three VM's, each using their own unique "bridge" interfaces. I have previously made a br0 interface off of eth0, but unfortunately, I am unable to add any more to it. It appears that you can only bridge 1 interface to the NIC. I would like to bridge many to one. Would a tap device be able to do this? If so, how would it be set up? Effectively, I am attempting to replicate what can easily be created with VirtualBox on Windows, where each VM is given a "bridged" interface, and can live on the network. I want to achieve this very same thing with Linux KVM. Thank You EDIT: To be more descriptive, I want to achieve something that looks like this: This can be found on this page: http://en.gentoo-wiki.com/wiki/KVM#Networking_2 HOST +---------------+ | | KVM GUEST1 | | +--------------+ | +------+ | | | LAN ---+--- eth0 | +--+---+---- nic0 | KVM GUEST2 | | tap0----+ | |192.168.1.13 | +--------------+ | | tap1----+ | +--------------+ | | | +------+ | | | | | br0 +--+----------------------+---- nic0 | |192.168.1.12 | |192.168.1.14 | +---------------+ +--------------+

  Read the article

• Remote Desktop *from* Windows 2008 R2 Server

  - by freefaller

  Summary: how do I create an RDC connection from a Windows 2008 server to another server? Our client will only allow us to connect to their server via a static IP address (which is fair enough), but unfortunately as we're a very small company we don't have one in the office. As a work around, we had the connection working through our old Windows 2003 server (dynamic-cloud from 1and1). .. however we have just rebuilt the server to run under Windows 2008 R2 (don't ask, but it was necessary), and now I simply cannot get the connection working. I have added an "Outbound Rule" to Windows Firewall with Advanced Security (TCP, All local ports, 3389 remote port - I have also tried the other way around). I have added a packet filter IP security rule with the same details. The 1and1 firewall rules (through their online control panel) allows for 3389 TCP and UDP. But it is simply not connecting (yes, the server is definitely on and able to accept connections) with the general error of... Remote Desktop can’t connect to the remote computer for one of these reasons: 1) Remote access to the server is not enabled 2) The remote computer is turned off 3) The remote computer is not available on the network Is there anything obvious I've missed - or something I can use to find out where the request is being blocked? The new server is using the exact same IP address as before, so I don't believe that would be an issue. Unless it's trying to use an IPv6 address rather than the old IPv4 address that it was before? I apologise that I am not a network person by trade, but I know more than anybody else in my office!!

  Read the article

• apache2 mysql authentication module and SHA1 encryption

  - by Luca Rossi

  I found myself in a setup on where I need to enable some authentication method using mysql. I already have an user scheme. That user scheme is working like a charm with MD5 password and CRYPT, but when I turn to SHA1sum it says: [Fri Oct 26 00:03:20 2012] [error] Unsupported encryption type: Sha1sum No useful debug informations on log files. This is my setup and some info: debian6 apache and ssl installed packages: root@sistemichiocciola:/etc/apache2/mods-available# dpkg --list | grep apache ii apache2 2.2.16-6+squeeze8 Apache HTTP Server metapackage ii apache2-mpm-prefork 2.2.16-6+squeeze8 Apache HTTP Server - traditional non-threaded model ii apache2-utils 2.2.16-6+squeeze8 utility programs for webservers ii apache2.2-bin 2.2.16-6+squeeze8 Apache HTTP Server common binary files ii apache2.2-common 2.2.16-6+squeeze8 Apache HTTP Server common files ii libapache2-mod-auth-mysql 4.3.9-13+b1 Apache 2 module for MySQL authentication ii libapache2-mod-php5 5.3.3-7+squeeze14 server-side, HTML-embedded scripting language (Apache 2 module) root@sistemichiocciola:/etc/apache2/sites-enabled# dpkg --list | grep ssl ii libssl-dev 0.9.8o-4squeeze13 SSL development libraries, header files and documentation ii libssl0.9.8 0.9.8o-4squeeze13 SSL shared libraries ii openssl 0.9.8o-4squeeze13 Secure Socket Layer (SSL) binary and related cryptographic tools ii openssl-blacklist 0.5-2 list of blacklisted OpenSSL RSA keys ii ssl-cert 1.0.28 simple debconf wrapper for OpenSSL my vhost setup: AuthMySQL On Auth_MySQL_Host localhost Auth_MySQL_User XXX Auth_MySQL_Password YYY Auth_MySQL_DB users AuthName "Sistemi Chiocciola Sezione Informatica" AuthType Basic # require valid-user require group informatica Auth_MySQL_Encryption_Types Crypt Sha1sum AuthBasicAuthoritative Off AuthUserFile /dev/null Auth_MySQL_Password_Table users Auth_MYSQL_username_field email Auth_MYSQL_password_field password AuthMySQL_Empty_Passwords Off AuthMySQL_Group_Table http_groups Auth_MySQL_Group_Field user_group Have I missed a package/configuration or something?

  Read the article

• Application to automate Windows software installation in a test lab

  - by Marc

  I have several test environments (hyper-V) which contain a variety of windows servers. Each machine needs periodically rolling back to a given snapshot and then re-installing with the latest version of our software to test. The software installs are quite complex MSI's with a fair few option screens. I know that the installs can be driven from the command line, passing in parameters to override the wizard options. At the simplest level I suppose I could just write a batch file to kick off each install with the required parameters, however the values that are passed in do need to change from time to time (and environment to environment) so a tool with a config file and simple GUI seems like a better idea. I think what makes it slightly more painful is the multiple environments. For example one environment might contain 4 servers and need a config file with all the server names, service endpoints etc. Another environment might be a 1-box install with all names and endpoints set to localhost. So, ideally I want to be able to store different setup configurations and use them to run all the required installers with the relevant settings against the relevant machines. Before I go off to write the thing, does anyone know of an existing, simple, free tool that will let me achieve this?

  Read the article

• Reduce power consumption of gaming computer while idle

  - by White Phoenix

  This is my current build: EVGA X58 (first generation) motherboard Intel i7 965 clocked @ 3.3 Ghz 3x DDR3-1600 Corsair RAM at stock timings and voltages Corsair AX750 80 Plus Gold PSU 1 Optical Drive 1 Seagate 7200.10 500 GB drive 2x Western Digital Caviar Black 1 TB drives OCZ Vertex 1 60 GB EVGA GTX 460 oc'd at 800/1600/1850 Antec 1200 case HT-Omega Striker 7.1 Sound Card Windows 7 32-bit Professional (PAE Enabled) I've already seen this post Reduce power use on computer and this post How do I lower power consumption of my computer and while useful, I'm looking for answers specific to my build and OS. I'm pretty sure this build is a energy-intensive build by default, but I want to try to reduce the amount of energy my build uses when I leave it idle (when I go to bed or go out, etc). The first requirement for this machine is that I need to leave it on, so I cannot turn it off while it's being unused. I run it as a file server for personal reasons and I also leave it on in case people leave me messages on various IM services and chat clients (IRC, MSN, Steam, XFire, Pidgin, etc). I'm also unable to replace the parts in my computer with a cheaper "greener" part. What are some ways to minimize the amount of power the machine uses? I'm already using a high efficiency power supply (80 Plus Gold), but I imagine there's other things that can be done in the BIOS and Windows' power settings to reduce power usage while I'm not using the computer. From what I can tell, I can't use Sleep since that'll disable network access (whole reason why I leave the computer on in the first place). I already turn off my monitor when it's not in use. I enabled Intel SpeedStep within the BIOS (I know, I have a 965 and why am I enabling SpeedStep?) Should I bring the graphics card back to stock speeds and lower the clock on the processor even more? Main reason why I'm asking is I think this computer alone is the reason why my power bill is high, so I want to reduce its consumption to as low as possible without having to shut the thing down.

  Read the article

• Cannot access domain from windows 2003 client

  - by Peuge

  Hey all, First off I am a novice at AD and DNS so please bear with me. This is my current situation: I have one server which is a DC and DNS server (win2k3) - Machine 1. I have another machine which is trying to join this domain - Machine2. This machine is also a win2k3 server. This is what I have done so far: I have setup DNS on the DC and its tcp/ip dns is pointing to itself. On machine2 I have set its dns to point to the dc. The DNS has been setup with a forward lookup zone with the same name as the domain (accdirect.com). I can ping machine1 from the machine2 by its FQDN and ip. I have set up forwarders on the DC for our ISP dns and can browse the internet on both machines. In the DNS mmc on the DC I can see a host (A) has been created for machine2. The problem is I still cannot join the domain. When I try join the domain via my computer - properties then it brings up the username/password box and after I go "ok" it says cannot find domain accdirect.com If I run this from machine2 dcdiag /s:accdirect.com /u:accdirect.com\admin /p: then I get the following: Performing initial setup: ** Warning: could not confirm the identity of this server in the directory versus the names returned by DNS servers. If there are problems accessing this directory server then you may need to check that this server is correctly registered with DNS [accdirect.com] Directory Binding Error 1722: Win32 Error 1722 This may limit some of the tests that can be performed. Done gathering initial info. On the dc all dcdiag and netdiag results pass. If anyone could help me I would really appreciate this! Sorry if any of my terminology is a bit off, I have only been doing this for two days. thanks Peuge

  Read the article

• filesystem compatible with freenas and windows

  - by Daniel

  Hi all, I'm planning on using FreeNAS (was considering openfiler but freenas seems simpler) for my home NAS box running off ESXI. I have managed to get local sata drives to mount in ESXI (http://serverfault.com/questions/216902/esxi-add-datastore-without-partitioning). I've had one of the drives fail on my before and I was able to retrieve most of the data off it using windows tools (I'm not much of a linux guy I know enough to be dangerous!). If I go the freenas route in the event that something goes bad what would be the best file system to use so that I could pop the drive out of the freenas box (vm) and put it in another pc running windows so I could try and run various recovery tools to get the data back. All in all its not a major problem if I lose the data just would be a bit annoying, so I'm not looking for suggestions around backing up etc. I was considering using NTFS that the drives are already formatted as but it appears that while freenas does support NTFS that its a bit buggy and not 100% reliable, anyone know if this is still true? Read that on a forum somewhere.

  Read the article

• Debian: Should I add vlan interface into bridge for KVM?

  - by javano

  I am setting up a Debian Squeeze box as a KVM host. I want to add multiple interfaces to each KVM guest so I want them to be on different VLANs. After reading about this, I believe the best method is to add multiple logical VLAN (sub)-interfaces to the physical NICs and then create a bridge adapter for each VLAN interace, and assign each bridge as a NIC for KVM guests. Does this make good sense, or madness? Do I have to use bridged interfaces with KVM like this? Can't I just add eth1.xx and eth1.yy to my interfaces config below and then configure those directly as bridged KVM guest NICs? If so, how should this look in the interfaces config file below? user@host:~$ cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # Management Interface auto eth0 iface eth0 inet static address 172.22.0.31 netmask 255.255.255.0 gateway 172.22.0.1 # Interface for guest VMs auto eth1 # Guest1 : Use VLAN 117 auto eth1.117 iface eth1.117 inet manual # Set up br1 for guest 1, bridging with vlan 117 auto br1.117 iface br1.117 inet manual bridge_ports eth1.117 bridge_stp off user@host:~$ uname -a Linux hostname 3.4.9 #1 SMP Wed Aug 22 19:08:46 BST 2012 x86_64 GNU/Linux UPDATE I would really like it if someone could clarify the config for me, as I have also seen the above configured with this syntax, so I don't see why one would be preferred over the other; # Interface for guest VMs auto eth1 allow-hotplug eth1 iface eth1 inet static # Vlan 117 for guest 1 auto vlan 117 iface vlan111 inet static vlan_raw_device eth1 # Guest 1 : NIC 1 auto br1.117 iface br1.117 inet manual bridge_ports vlan117 bridge_stp off

  Read the article

• Blinking power button

  - by Mike Ramsey

  A friend asked me to look at his Gateway DX4640 desktop. When he presses the power button, power goes to the mobo (NVIDIA nForce 630i MCP73PV, GeForce 7100 chipset) and the CPU fan starts spinning. The power button slowely blinks on and off (blue) and the screen briefly says no signal and then goes black. And nothing else; no post code beeps. My initial two conjectures were: 1. Vista was stuck in sleep/hibernation mode, or 2. A power off had left the mobo in a bad state. The fix for both is to: a) Unplug the AC power cord b) hold the power button for 30 second to fully discharge the mobo It didn't help. I left the system unplugged from AC power for an hour. No change. I am out of ideas. Has anybody seen anything like this before? What does a blinking blue power button mean? How can I get more data points to guide trouble shooting? --Thank you, --Mike

  Read the article

• Google Chrome doesn't delete my browsing history correctly

  - by Derfder

  I have deleted everything that I could from my browser history: chrome://settings/clearBrowserData I checked everything and select the begining of time Then when I access browsing history: chrome://history/ There is nothing (as I expected), or to be precise No history entries found. The problem is that I still see my specific search url with very specific query I have made a month ago, when I start typing the url of the website into chrome address bar. How is that possible? Where is Google stroing these data. How to get rid off them completely? I want to mention that my autosuggestion options look like this: So, what else should I delete to remove everything from autosuggestions? Right now it has some specific URLs (subpages, pages with very specific search query I have made in a month or so). I have tried restarting Chrome and restarting my computer, but the urls are still in the autosuggestion. Also I am unable to turn off the autosuggestion, even I have unchecked that option in settings. My Google Chrome version is: Version 27.0.1453.116 m (probably the latest) Btw. in Firefox deleting the history works as expected. So, I guess that this has nothing to do with the operating system I am using (Windows 7), but only it's an issue with Chrome itself.

  Read the article

• CUPS causes printer to click and doesn't print

  - by Pez Cuckow

  I'm suffering a strange problem with my Cannon iP4850 when trying to use CUPS on a Raspberry Pi (this is not RPi specific, please do not vote to move it). When I plug the printer into my Laptop (OSX) or my Desktop W7 it identifies as a iP4800 and prints perfectly. So I plug it into the Pi (running debian), set it up in CUPS enable sharing and can now see the iP4800 series shared on the network. However if I print to it (using AirPrint etc...); the file gets to CUPS safely (shows in the queue) but when it tries to print the printer clicks (like a loud thunk) 3/4 times and then gives in, with a double amber flashing light. In cups it shows as job completed. Do you know why using the pi and cups would cause what appears to be a hardware fault and what I can do to fix the problem or to provide further debug info? Thanks for your time! Description: Canon iP4800 series Location: Lounge Driver: Canon PIXMA iP4800 - CUPS+Gutenprint v5.2.9 (color, 2-sided printing) Connection: usb://Canon/iP4800%20series?serial=2239B2 Note: I've tried deleting and re-adding the printer to the Laptop, Desktop and PI and the results are always the same Log for plugging in printer and printing (attempting to) something until the printer turned off again pi@pezpi /var/log $ dmesg [ 7284.176336] usb 1-1.2: new high speed USB device number 8 using dwc_otg [ 7284.279703] usb 1-1.2: New USB device found, idVendor=04a9, idProduct=10d5 [ 7284.279750] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7284.279771] usb 1-1.2: Product: iP4800 series [ 7284.279786] usb 1-1.2: Manufacturer: Canon [ 7284.279800] usb 1-1.2: SerialNumber: 2239B2 Setting cups to verbose: Change loglevel in cupsd.conf to debug (or debug2) pi@pezpi /var/log $ sudo vim /etc/cups/cupsd.conf pi@pezpi /var/log $ sudo /etc/init.d/cups restart [ ok ] Restarting Common Unix Printing System: cupsd. pi@pezpi /var/log $ Log from $ /var/log/cups/error_log is at http://pastebin.com/7VZMRMrG (too large to post here) The log contains - in order (deleted the log and then did the beneath) Restarting the cups server Attempting to print a test page x2 Printing from 192.168.1.90 via AirPrint Printing from 192.168.1.90 via Network Print Turning the printer off and on again

  Read the article

• Building a PC for Work and play? [closed]

  - by Derek Organ

  Ok, Its been a long time since I build my own PC so I'm looking to get back into it again and build a new one. First off budget is about €800 excluding the monitor and windows 7 licence and mouse. (just bought a new g500) I plan on using my computer for work, lots of applications open at once but none particularly excessive (photoshop being the most demanding, mostly coding tools) I also use it for some gaming, e.g. COD, Starcraft etc. One thing I do want to do eventually is get a really good monitor with hight resolution and maybe 27" so the graphics card needs to be able to make best use of that. So a few questions 1) Is the bottle neck in performance mostly still the harddrives? 2) Aren't most processors e.g. i5 etc even i3 so far a head of other bottlenecks it makes litte difference the higher you go. Isn't the Graphics card dealing with heavy graphics so what really slows because of a slow CPU? So from this my thinking is to get a SSD drive as my primary drive for OS etc and have loads of memory e.g. 6-8GB and a decent mid level graphics card? It doesn't seem at my level worth spending much on CPU and any other parts really. I basic parts off the top of my head Case, Motherboard CPU SSD Drive SATA Drive Power Supply Memory Cooling (fan?) Graphics Card Network Card Keyboard DVD drive Mouse Windows Monitor Am I missing anything? Any helpful tips or general education much appreciated. Thanks, Derek

  Read the article

• bond0 and xen = crash

  - by Rajat

  Bonding with xen 1 - Stop all guests. Reboot dom0 after running "chkconfig xend off" and "chkconfig xendomains off". 2 - Configure bond0 by enslaving eth0 and eth1 to it. I added the below two entries to /etc/modprobe.conf. alias bond0 bonding options bond0 mode=6,miimon=100 Content of /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 USERCTL=no ONBOOT=yes MASTER=bond0 SLAVE=yes BOOTPROTO=none Content of /etc/sysconfig/network-scripts/ifcfg-eth1 DEVICE=eth1 USERCTL=no ONBOOT=yes MASTER=bond0 SLAVE=yes BOOTPROTO=none Content of /etc/sysconfig/network-scripts/ifcfg-bond0 DEVICE=bond0 IPADDR= NETMASK= ONBOOT=yes BOOTPROTO=static USERCTL=no Did "modprobe bond0" and "service network restart" after that. 3 - Edit /etc/xen/xend-config.sxp Change (network-script network-bridge) To (network-script 'network-bridge netdev=bond0') 4 - Start xend. "service xend start". 5 - chkconfig xend on. 6 - modprode bond0 7 - more /proc/net/bonding/bond0 8 - Create guest images as usual and bridge it to xenbr0. about config i did for my xen kernel rhel 5.3 after i reboot the host server i get in place bond0 get pbond0 and its get disconnect from network only i ping to my vm's on the host server any one have any idea why xen bond0 is acting like that or what is solutions to come out of pbond0 to bond0.

  Read the article

• TV won't go into standby

  - by Robert

  When I select Start-Turn off computer-Standby the 'turn off computer' option window closes, and then nothing else happens. I can start new applications, and Windows acts like I never selected standby. I ran it for several hours after that. If I have a TV program scheduled to record when I select standby I get a window (the Pinnacle TV software) asking if I'm sure, there are programs scheduled to record - and the computer just keeps running after I select yes, never going into standby. I added that detail as it shows the standby process is starting. [This problem also happens if a TV program is not scheduled, so the scheduler task in not running/in memory. This problem happens regardless of whether I'm not watching TV. This problem happens regardless of whether Media Center is running (it usually isn't, I'm using Pinnacle to watch TV).] I looked at "How to troubleshoot hibernation and standby issues in Windows XP" http://support.microsoft.com/kb/907477 - ACPI is enabled, and "standby" is an option in "Power Options Properties." So it appears to be setup correctly. Windows XP SP3 Media Center Edition, all current updates installed.

  Read the article

• Apache + PHP via FastCGI

  - by Wilco

  I'm running into some problems while attempting to run PHP via FastCGI in Apache. I have the FastCGI module loaded, but get the following error when attempting to load a page: The requested URL /fastcgi/php54.fcgi/index.php was not found on this server. Somewhere, it seems that the script to be executed is appended to the executable without any spaces. Is this where the problem likely is? Below I've included snippets from my Apache configuration (hopefully this is enough): LoadModule fastcgi_module libexec/apache2/mod_fastcgi.so FastCgiIpcDir /var/run/fastcgi AddHandler fastcgi-script .fcgi FastCgiConfig -autoUpdate -singleThreshold 100 -killInterval 300 AddType application/x-httpd-php .php ScriptAlias /fastcgi/ /Library/WebServer/FCGI-Executables/ <Directory "/Library/WebServer/FCGI-Executables"> Options +ExecCGI SetHandler fastcgi-script Order allow,deny Allow from all <VirtualHost *:80> ServerName www.somedomain.com ServerAdmin [email protected] DocumentRoot "/Web/www.somedomain.com" DirectoryIndex index.html index.php default.html CustomLog /var/log/apache2/access_log combinedvhost ErrorLog /var/log/apache2/error_log Action application/x-httpd-php /fastcgi/php54.fcgi <IfModule mod_ssl.c> SSLEngine Off SSLCipherSuite "ALL:!aNULL:!ADH:!eNULL:!LOW:!EXP:RC4+RSA:+HIGH:+MEDIUM" SSLProtocol -ALL +SSLv3 +TLSv1 SSLProxyEngine On SSLProxyProtocol -ALL +SSLv3 +TLSv1 </IfModule> <Directory "/Web/www.somedomain.com"> Options All -Indexes +ExecCGI +Includes +MultiViews AllowOverride All <IfModule mod_dav.c> DAV Off </IfModule> <IfDefine !WEBSERVICE_ON> Deny from all ErrorDocument 403 /customerror/websitesoff403.html </IfDefine> </Directory> </VirtualHost> ... and this is the executable: #!/bin/sh PHP_FCGI_CHILDREN=1 PHP_FCGI_MAX_REQUESTS=5000 export PHP_FCGI_CHILDREN export PHP_FCGI_MAX_REQUESTS exec /opt/local/bin/php-cgi54

  Read the article

• Measure Total Bandwidth for Billing

  - by TonyZ

  I am setting up a new network which customers will host their applications on. It needs to be able to scale out to a few hundred servers and each server will have several VMs on it. Right now in my test environment, after the telco router, we are using a Linux router/firewall which is then connected to a Layer 2 switch. Could be a layer 3 in the future. I need to track total bandwidth per VM for each machine, and I need to do it in a way that it is not part of the VM. Each VM will have a private class ip address which is Natted by the gateway, or we may eventually run more than firewall/reverse proxy off a layer 3 switch. So my thinking is that I can do it off of a promiscuous port on the switches, or at the gateway firewall. I would like to have an out of the box solution, preferably open source. Does anyone have suggestions on the easiest way to set this up, and the easiest tool to use. I have looked at the web sites for Nagios, Zenoss, Zabbix, ntops on the firewall, etc. It is hard to ascertain just from the web sites if they do exactly this or not. Obviously, performance is also somewhat key here. Anything running on the gateway should not drag it down doing traffic accounting. Thanks for any thoughts. Tony Zakula

  Read the article

• Dell XPS 17 Laptop USB SS Ports don't work until machine rebooted

  - by Matt

  I have a new Dell XPS 17 laptop and have an issue that the two USB SS ports on the rear of the machine are not recognising anything when I start-up. Have tried mouse, keyboard, headset, USB display. If I plug a USB hub in the power light on the hub lights (presume this is hard-wired) but a mouse plugged into the hub does not light up. If I restart the pc the ports work fine. Also the other two USB ports work fine all the time. I have switched off the power saving setting on the device manager (Power managementAllow the computer to turn off this device to save power) and also in the advanced power settings (USB Settings USB Selective suspend setting:disabled) I have also disabled USB powershare in the BIOS (not sure what this actually does!) This is becoming very annoying having to restart the machine every day before I can start work Running Win 7 Pro x64 EDIT: I have found that setting USB Emulation to Disabled has helped the devices to be recognised during start up but they keep dropping out completely when in use EDIT 2: I contacted Dell about this issue who told me to update the BIOS driver, when I asked if I should downgrade from the factory installed A13 to the A12 posted on the dell website they said no. However there is now an A14 available on the website has anyone tried this?

  Read the article

• How can I disable Kerberos authentication for only the root of my site?

  - by petRUShka

  I have Kerberos-based authentication and I want to disable it on only root url: http://mysite.com/. And I want it to continue to work fine on any other page like http://mysite.com/page1. I have such things in my .htaccess: AuthType Kerberos AuthName "Domain login" KrbAuthRealms DOMAIN.COM KrbMethodK5Passwd on Krb5KeyTab /etc/httpd/httpd.keytab require valid-user I want to turn it off only for root URL. As workaround it is possible to turn off using .htaccess in virtual host config. Unfortunately I don't know how to do it. Part of my vhost.conf: <Directory /home/user/www/current/public/> Options -MultiViews +FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> UPD. I'm using Apache/2.2.3 (Linux/SUSE) I tried to use such version of .htaccess: SetEnvIf Request_URI ^/$ rootdir=1 Allow from env=rootdir Satisfy Any AuthType Kerberos AuthName "Domain login" KrbAuthRealms DOMAIN.COM KrbMethodK5Passwd on Krb5KeyTab /etc/httpd/httpd.keytab require valid-user Unfortunately such config turn Kerberos AuthType for all URLs. I tried to place first 3 lines SetEnvIf Request_URI ^/$ rootdir=1 Allow from env=rootdir Satisfy Any after main block, but it didn't help me.

  Read the article

• Is there a way to do something like LVM over NFS?

  - by warren

  I realize that since NFS is not block-level, LVM can't be used directly. However: is there a way to combine multiple NFS exports (from, say, 3 servers) into one mount point on a different server? Specifically, I'd like to be able to do this on RHEL 4 (or 5, and re-export the combined mount to my RHEL 4 server). expansion The reason I pegged lvm is that I want a bunch of exported mounts (servera:/mnt/export, serverb:/mnt/export, serverc:/mnt/export, etc) to all mount at /mnt/space so that my /mnt/space on this server (serverx) as one large filesystem. Yes, I know that re-exporting is generally a Bad Thing™ but thought it might work, if there was a way to accomplish this on a newer release as opposed to an older one From reading the unionfs docs, it appears that I can't use it over a remote connection - have I misread it? More accurately, since Union FS merges the contents of multiple branches, but makes them appear as one, it doesn't seem to go in reverse: I'm trying to mount a bunch of NFS points in a merged fashion, then write to them - not caring where data goes, a la LVM .

  Read the article

• Prevent outgoing traffic unless OpenVPN connection is active using pf.conf on Mac OS X

  - by Nick

  I've been able to deny all connections to external networks unless my OpenVPN connection is active using pf.conf. However, I lose Wi-Fi connectivity if the connection is broken by closing and opening the laptop lid or toggling Wi-Fi off and on again. I'm on Mac OS 10.8.1. I connect to the Web via Wi-Fi (from varying locations, including Internet cafés). The OpenVPN connection is set up with Viscosity. I have the following packet filter rules set up in /etc/pf.conf # Deny all packets unless they pass through the OpenVPN connection wifi=en1 vpn=tun0 block all set skip on lo pass on $wifi proto udp to [OpenVPN server IP address] port 443 pass on $vpn I start the packet filter service with sudo pfctl -e and load the new rules with sudo pfctl -f /etc/pf.conf. I have also edited /System/Library/LaunchDaemons/com.apple.pfctl.plist and changed the line <string>-f</string> to read <string>-ef</string> so that the packet filter launches at system startup. This all seems to works great at first: applications can only connect to the web if the OpenVPN connection is active, so I'm never leaking data over an insecure connection. But, if I close and reopen my laptop lid or turn Wi-Fi off and on again, the Wi-Fi connection is lost, and I see an exclamation mark in the Wi-Fi icon in the status bar. Clicking the Wi-Fi icon shows an "Alert: No Internet connection" message: To regain the connection, I have to disconnect and reconnect Wi-Fi, sometimes five or six times, before the "Alert: No Internet connection" message disappears and I'm able to open the VPN connection again. Other times, the Wi-Fi alert disappears of its own accord, the exclamation mark clears, and I'm able to connect again. Either way, it can take five minutes or more to get a connection again, which can be frustrating. Why does Wi-Fi report "No internet connection" after losing connectivity, and how can I diagnose this issue and fix it?

  Read the article

< Previous Page | 144 145 146 147 148 149 150 151 152 153 154 155  | Next Page >