Search Results

Search found 16902 results on 677 pages for 'trade off'.

Page 152/677 | < Previous Page | 148 149 150 151 152 153 154 155 156 157 158 159  | Next Page >

• USB seems to pause system

  - by Marco van de Voort

  I've an application that does some simple measuring, for which it polls a few 100kbs several times a second (8-25 times) The behaviour is not really dependant on chipset (happens on several mobo's intel 965- P55) and OSes (XPsp3 and win7). Also the make of the USB keyboard doesn't seem to matter. I notice that sometimes when an USB kbd is plugged in, the system pauses for say 500-1000ms. (about 900-1000ms on disconnect, and 400-500 on the subsequent connect) It also happens for other USB devices (most notably mice and massstorage devices), but only the first time such device is connected to an installation. This disrupts the measurement and I really would like to get rid on this. I already tried to disable as much as possible. (powersave, teletubby mode (*) etc), and while this helped with the non-USB related disruptions of the measurement, it doesn't help with the USB related ones. (*) fyi, turning off themes (to resp. classic/non-aero), and turning off effects in system solved problems that occured when minimizing/maximizing the app. Any pointers to look into? I'm a bit stuck with this.

  Read the article

• How to calibrate ASUS k52f battery on Ubuntu?

  - by cutalion

  I'm not sure if the problem is in software or my battery is dying, I'll move my question to another forum if it's not a SO question I have a problem with the battery on my laptop - ASUS K52F. It shows incorrect information about capacity. When I unplug the charger it can work some time, but then it will power off without any warnings. Sometimes it will power off right after I unplug the charger. Here is some info I could get: > uname -a Linux alligator 3.5.0-18-generic #29-Ubuntu SMP Fri Oct 19 10:26:51 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux > acpi -i Battery 0: Charging, 99%, 18:25:15 until charged Battery 0: design capacity 5235 mAh, last full capacity 69964 mAh = 100% > cat /sys/class/power_supply/BAT0/uevent POWER_SUPPLY_NAME=BAT0 POWER_SUPPLY_STATUS=Charging POWER_SUPPLY_PRESENT=1 POWER_SUPPLY_TECHNOLOGY=Li-ion POWER_SUPPLY_CYCLE_COUNT=0 POWER_SUPPLY_VOLTAGE_MIN_DESIGN=10800000 POWER_SUPPLY_VOLTAGE_NOW=9246000 POWER_SUPPLY_POWER_NOW=176000 POWER_SUPPLY_ENERGY_FULL_DESIGN=**48400000** POWER_SUPPLY_ENERGY_FULL=**646822000** POWER_SUPPLY_ENERGY_NOW=**643588000** POWER_SUPPLY_MODEL_NAME=K52F-44 POWER_SUPPLY_MANUFACTURER=ASUSTek POWER_SUPPLY_SERIAL_NUMBER= I noticed, that POWER_SUPPLY_ENERGY_NOW and POWER_SUPPLY_ENERGY_FULL are greater than POWER_SUPPLY_ENERGY_FULL_DESIGN. I don't think it's ok :) I can run any additional commands.

  Read the article

• Configure Nginx to render static files and rewrite file extension or proxy_pass

  - by Pardoner

  I've set up Nginx to handle all my static files else proxy_pass to a Node.js server. It's working fine but I'm having difficulty rewriting the url so that it remove the .html file extension. upstream my_upstream { server 127.0.0.1:8000; keepalive 64; } server { listen 80; server_name staging.mysite.com; root /var/www/staging.mysite.org/public; access_log /var/logs/staging.mysite.org.access.log; error_log /var/logs/staging.mysite.org.error.log; location ~ ^/(images/|javascript/|css/|robots.txt|humans.txt|favicon.ico) { rewrite (.*)\.html $1 permanent; try_files $uri.html $uri/ /index.html; access_log off; expires max; } location / { proxy_redirect off; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header X-Forwarded-Proto $scheme; proxy_set_header Host $http_host; proxy_set_header X-NginX-Proxy true; proxy_set_header Connection ""; proxy_http_version 1.1; proxy_cache one; proxy_cache_key sfs$request_uri$scheme; proxy_pass http://my_upstream; } }

  Read the article

• Borked ubuntu uninstall - need to delete boot partition (i think)

  - by Max Williams

  I just got a new pc laptop with windows 7 and wanted to install Ubuntu on it. Which i did, no problem there, by downloading the installer, burning it to dvd then booting off the dvd and installing. Then, i realised that the new Ubuntu 12.04 uses the Unity desktop, which i immediately disliked, and after some research, began to hate. So, i decided (after a little googling) to install Linux Mint instead. So, thinking i'd better start from scratch, i went to the Windows 7 disk manager and wiped the Ubuntu partition that had been created. Now, when i start up, i get an error from grub, the ubuntu boot manager: error: unknown filesystem grub rescue> _ and a blinking cursor where i can enter commands. I suspect that what i've done is deleted the main ubuntu partition but NOT deleted another partition which is a boot partition, or something like that? Can anyone tell me how i can rescue or unbork this? I'd like to either a) get back to my original windows-only setup OR b) install linux mint off dvd (which i have), into the empty partition, fixing any grub confusion in the process. Any suggestions? Thanks, max BTW please don't answer if you're just going to tell me to stick with 12.04, or install a different distro or something. I definitely want Mint and just want to fix this mess - thanks :)

  Read the article

• Retrieve a user's Exchange database in powershell

  - by Paul

  Hey Everyone, I've scoured the interwebs for a few days now off and on to find this. I am creating a powershell script for email-enabling new user's(Exchange 2007). To give you a little background when we have a new hire, their AD account is created at our off-site helpdesk, but they don't create their email account. I'm trying to automate the process of mail-enabling the user which involves putting them in the same database as an existing user, disable imap pop activesync, and lastly email the requester of the ticket. I would like to just get prompted for the New User's name, User to Replicate(mailbox, storage group, database), and the person to email after it's been created. So if someone could just help with a command to Retrieve a user's Exchange database in powershell that would be great, but if people also want to help with my hacked up script please do so as well!!! Here is what I have so far: Write-output “ENTER THE FOLLOWING DETAILS” $DName = Read-Host “User Diplay Name" $RUser = Read-Host "Replicate User(Database Grab)" ***$RData = #get the Replicate user's mailbox database here*** $REmail = #either just use a Read-Host “Requester's Email address" or ask for Requester's name and pipe through their email address by digging for it w/ powershell Enable-Mailbox -Identity "$DName" -Database "$RData" Send-MailMessage -From "John Doe <[email protected]>" -To (put $REmail here which is the Requester's email) -Subject "Test Person's email account" -Body "Test Person's email account has been setup.`n`n`nJohn Doe`nGeneric Company`nSystems Administrator`nOffice: 123.456.7890`[email protected]" -SmtpServer genericexchange.exchange.com

  Read the article

• Apache proxy: Why is one vhost returning Forbidden while the other one works?

  - by Stefan Majewsky

  I have a Java application that needs to talk to another intranet website using HTTPS in both directions. After fighting with Java's SSL implementations for some time, I gave up on that, and have now set up an Apache that's supposed to act as a bidirectional reverse proxy: external app ---(HTTPS request)---> Apache ---(local HTTP request)---> Java app This direction works just fine, however the other direction does not: Java app ---(local HTTP request)---> Apache ---(HTTPS request)---> external app This is the configuration for the vhost implementing the second proxy: Listen 127.0.0.1:8081 <VirtualHost appgateway:8081> ServerName appgateway.local SSLProxyEngine on ProxyPass / https://externalapp.corp:443/ ProxyPassReverse / https://externalapp.corp:443/ ProxyRequests Off AllowEncodedSlashes On # we do not need to apply any more restrictions here, because we listened on # local connections only in the first place (see the Listen directive above) <Proxy https://externalapp.corp:443/*> Order deny,allow Allow from all </Proxy> </VirtualHost> A curl http://127.0.0.1:8081/ should serve the equivalent of https://externalapp.corp, but instead results in 403 Forbidden, with the following message in the Apache error log: [Wed Jun 04 08:57:19 2014] [error] [client 127.0.0.1] Directory index forbidden by Options directive: /srv/www/htdocs/ This message completely puzzles me: Yes, I have not set up any permissions on the DocumentRoot of this vhost, but everything works fine for the other proxy direction where I haven't. For reference, here's the other vhost: Listen this_vm_hostname:443 <VirtualHost javaapp:443> ServerName javaapp.corp SSLEngine on SSLProxyEngine on # not shown: SSLCipherSuite, SSLCertificateFile, SSLCertificateKeyFile SSLOptions +StdEnvVars ProxyPass / http://localhost:8080/ ProxyPassReverse / http://localhost:8080/ ProxyRequests Off AllowEncodedSlashes On # Local reverse proxy authorization override <Proxy http://localhost:8080/*> Order deny,allow Allow from all </Proxy> </VirtualHost>

  Read the article

• Wake on Lan Remote not waking PC while the PC does receive the packet.

  - by Nycrea

  Over the last couple of weeks, I have been trying to set up WOL from a remote location. When I use my laptop to wake the machine locally, it works just fine. (for some reason, when I try to wake from my phone with an app called "WOL wake on lan" it does not work locally either, but I'll get to that later) Anyway, when the machine is turned on, and I let it 'listen' for incoming magic packets (with a program called "WOL magic packet sender") on my specified port, it does receive them, though when turned off, the machine does not wake. When sending from phone, either locally or via 3G remotely, it does receive but does not wake as well. Because the machine does receive them when turned on and listening, but does not wake when turned off, I am convinced the cause of the problem is my receiving PC, rather than the router or the sender. Some extra info: The receiving machine is a PC running Windows 7 64bit. My router is the Netgear JWNR2000v2. I have the port I use forwarded to my PC's static IP in the router. If anyone could help, or just share your own story with the same problem, maybe we can work this out. Thanks a lot in advance.

  Read the article

• iTunes copy just metadata (song and album ratings, playlists) from iPod

  - by Jared Updike

  I have an iPod touch that I synched with my Windows computer (iTunes 9.0 I think) until my harddrive failed and I lost my entire library. I rebuilt the library (songs) from a year old backup (and various other source for songs) but my playlists and ratings are of course a year old. My iPod itself has most of the playlists and ratings I care most about (favorite songs and albums, rated 4 and 5, for example). I have a catch 22 situation where I feel nervous that I haven't backed up my iPod in around 4 months (when my drive failed) so I'd like to back it up as soon as possible... but if I back it up I have to clear all the songs and playlists and copy them back, which I can't really do since I need to rebuild my playlists on my computer first (using the data only available on my iPod!) The question: is there a better way to READ the information off my iPod than doing it manually, song by song and album by album and playlist by playlist (XML, text dump, database, spreadsheet, anything). In other words, mostly I want the information (metadata like ratings and playlists, not songs) copied off the iPod so I can more quickly get my iTunes library ratings and playlists re-built (manually) so I can finally wipe the music and back up my apps, etc. Then I'd like to copy the music back immediately. The part I'd like to avoid is manually navigating everything on my iPod to read through all the playlists and ratings (50 GB, 6,000+ songs) as I re-enter all of that data by hand. I've done a few dozen albums and it's pretty time consuming having to tap around on the iPod. Reading from a spreadsheet (for example, or XML which I could write a script to get into spreadsheet form) would probably help tremendously, plus then I'd have a backup of that information somewhere besides just my iPod.

  Read the article

• I think my laptop just died

  - by Joel Coehoorn

  I have a Dell 1330M that as of about 15 minutes ago will no longer POST. What happened was I was working, stepped away for a moment, and when I came back it was turned off. I thought that was odd, but turned it on and things seemed fine. About 1/2 hour later it crashed and restarted, but came up fine again. It did this once more. At this point I was starting to get worried, but I hadn't had any problems with the laptop before and every crash was after doing some work in a virtual machine that I don't often use, so I at put the blame there. It didn't feel like it was overheating anywhere and there's no ozone smell of overheated electronics. Then it crashed a final time and now when I turn it on all I see is a bright screen with a bunch of vertical lines (noise). I've tried removing the memory sticks one at a time, but I get the same result with either memory stick in either slot. With no memory at all it stops earlier in the POST process and the screen is completely blank (black, no backlight). As I type this, I hear a double beep from the system about once every 10 minutes. I'm pretty sure the hard drive is fine because it fails during post, before anything off the drive is needed. The power supply seems good because the screen is nice and bright. It's not the RAM because swapping that around made no difference. The leaves motherboard (which I doubt and can replace) and CPU (which just might be changable). Any ideas? Is there any hope for this laptop? I'm rather fond of it and I'd have a hard time replacing it with anything near as nice.

  Read the article

• Toshiba A205-5804 freezes when plugged in

  - by heron

  Well I have a Toshiba A205-5804 and the problem is that the screen freezes anytime I plug the pc into the external power supply, not as most of the computers having the same issue, my computer DOES freeze in safe mode, and I really can't bear this problem for much longer... It's not an overheating problem, the computer is not getting hot or anything related, I've already tried changing the AC adapter, booting only with AC and no battery, and also all of these suggestions: Try changing the following setting in the bios setup, under the 'Advanced' tab Dynamic CPU Frequency: Mode = Always Low (NOT DYNAMIC) My laptop has been running on AC power without a problem for 24hours, including many restarts, and when I went back to the original bios setting, the problem returned almost straight away. EDIT Other suggestions I found on the web from here and here: Set the power plan to high performance Set the power plan to "Minimal Power Management" (1 and 2 do conflict) Start - Control Panel - Device Manager -- Processor - disable one of two processors - reboot normally 4.Do this: Only plug battery into laptop Turn on the laptop and start Windows normally Plug AC adapter into laptop, the screen will freeze Leave the laptop the way it is for 12-24 hours After 12-24 hours, turn it off the hard way Once it is turned off, turn it back on. The laptop is working now. I have no idea of what can it be...

  Read the article

• IBM BladeCenter S: Disk Configuration

  - by gravyface

  Have just the one storage bay right now (SAS 15K 600GB x 6) and have configured one storage pool in RAID 10 with 4 disks (and two global spares). For each blade, I've created a volume and mapped accordingly: Blade #1 400 GB Blade #2 200 GB Blade #3 100 GB Blade #4 100 GB When I boot up Blade 1 and enter into the UEFI Setup (F1) followed by the Adapters and UEFI Drivers LSI Logic Fusion MPT SAS Driver Utility, I see 4 disks: two are the on-board 73GB drives, the other two are 200GB each and assume I'm being presented with two logical disks from the volume I created and mapped to this blade. I was a bit surprised by this: I figured I would've been presented with one logical drive per volume, not two. I'm assuming I can just configure whatever RAID level I wish that supports two disks, but not really sure what the benefits/trade-offs here. Should I go with RAID 10 on top of RAID 10? RAID 0? Software RAID 0/1/10? Does it even matter? If this is "normal" to see two disks, then I'm going to likely just do some benchmarking and see if it makes a difference changing the RAID levels (my guess is no); if this is not normal, well, please let me know. :)

  Read the article

• Windows Not Honoring DHCP Scope

  - by jerhinesmith

  Please bear with me as I'm not a networking person by trade. Our current configuration at work includes two Windows Servers serving as DHCP/Active Directory servers (if that makes sense) -- one replicating from the other. On both machines, the DNS resolution is set up as: Main Windows Box (10...* address) Public IP Address (for Verizon) Public IP Address (secondary Verizon) Secondary Windows Box (10...* address) Assuming our domain is foo.com, we maintain the foo.com website on a hosted VPS with it's own IP address. The problem is that even though bar.foo.com is an internal server and is defined in DNS on the Primary Windows machine, when I ping bar or even bar.foo.com it resolves to the hosted IP address instead of the 10.* address. I tried taking both of the Public IP addresses out of the DHCP scope, and that seemed to work, but it completely slowed down access to any external sites, so that wasn't acceptable. I also tried adding the two Windows machine as the DNS servers on my desktop. That too worked, but I'd rather not have everything enter their DNS servers, as the above setup should theoretically be working. Is there anything I could check to see why pinging bar.foo.com isn't resolving to the DNS entry on the Windows machines? Here's a summary of the ping results, if they help: Pinging from servers with static IP bar.foo.com resolves with correct IP address Pinging from linux machines not joined to the domain bar.foo.com resolves with correct IP address Pinging from user's desktop machines, joined to the domain, but dynamic IP bar.foo.com resolves with incorrect IP address This is driving me crazy!

  Read the article

• xen + debian network after upgrade squeeze to wheeze

  - by rush

  I've got a Debian + Xen server. After a system upgrade to the stable version the network doesn't come up after boot. Every time after reboot I need to bring it up manually. The network configuration was not changed during upgrade. Here is /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 11.22.33.44 netmask 255.255.255.0 gateway 11.22.33.1 nameserver 8.8.8.8 After boot ip r shows no route and eth0 has no ip address. Manually ip and route setup goes fine and network starts working. Messages from dmesg about network I've found (looks like nothing interesting) [ 3.894401] ACPI: Fan [FAN3] (off) [ 3.894444] ACPI: Fan [FAN4] (off) [ 4.178348] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c9 [ 4.178351] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection [ 4.178392] e1000e 0000:00:19.0: eth0: MAC: 10, PHY: 11, PBA No: 0100FF-0FF [ 4.178413] e1000e 0000:02:00.0: Disabling ASPM L0s L1 [ 4.178432] xen: registering gsi 16 triggering 0 polarity 1 -- [ 4.223667] ata5: DUMMY [ 4.223668] ata6: DUMMY [ 4.289153] e1000e 0000:02:00.0: eth1: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c8 [ 4.289155] e1000e 0000:02:00.0: eth1: Intel(R) PRO/1000 Network Connection [ 4.289245] e1000e 0000:02:00.0: eth1: MAC: 3, PHY: 8, PBA No: 1000FF-0FF [ 4.506908] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 4.542920] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) -- [ 10.362999] EXT4-fs (dm-23): mounted filesystem with ordered data mode. Opts: (null) [ 10.419103] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null) [ 10.988255] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 13.175533] Event-channel device installed. [ 13.287555] XENBUS: Unable to read cpu state -- [ 13.288670] XENBUS: Unable to read cpu state [ 13.965939] Bridge firewalling registered [ 14.134048] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 14.283862] ADDRCONF(NETDEV_UP): peth0: link is not ready [ 14.284543] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 17.800627] e1000e: peth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 17.801377] ADDRCONF(NETDEV_CHANGE): peth0: link becomes ready [ 18.307278] device peth0 entered promiscuous mode [ 24.538899] eth1: no IPv6 routers present [ 28.570902] peth0: no IPv6 routers present I've upgraded two servers and I've such behaviour on two of them. How to fix this and get network starts automatically on boot?

  Read the article

• Disappeared graphics card

  - by lenovo user

  I have a Lenovo T520 with two graphics cards, an nVidia quadro and an intel graphics card. I'm running a Ubuntu and Windows 7 dual boot. I can no longer find any trace of my intel graphics card. In my linux boot: > lspci | grep VGA > 01:00.0 VGA compatible controller: nVidia Corporation GF106 [Quadro 2000M] (rev a1) In Windows in control panel display- advanced settings, I only see the NVIDIA Quadro 2000M. In the BIOS there is no mention of the intel graphics card, no where I can find to try and turn it on or off. I thought I was going crazy, but then I found a post I made on ask ubuntu I made 3 months ago where I listed the output of lspci on this same machine: lspci | grep VGA 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 01:00.0 VGA compatible controller: nVidia Corporation GF106 [Quadro 2000M] (rev a1) What is going on? How could my intel graphics card have been disabled or turned off somehow without my knowledge? I've been in the BIOS 3 times now, each time convinced the last time I must have missed something, but I always find nothing. Am I missing something there? Could a thief have opened my computer and stolen my graphics card?

  Read the article

• Computer does not boot, often

  - by tam

  I've ran into a issue with my computer that it does no longer reach POST, but simply powers on for a fraction of a second and powers off. But this is not always, some times it boots just normally and it works as it should, no issues with not enough power or anything. But as soon as I turn it of, I can not turn it back on, but then again at some random point it just powers up again, and resumes normal operation. If I disconnect the 8pin ATX connector from the motherboard, it powers up, fans and disks spinning normally until I power it off again. So this problem only happens when ATX is connected, which seems odd, I normally always saw this kind of an error if ATX was not connected, but here it's the exact opposite. It also does not emit any sound on the buzzer, except the normal beep, when it powers up normally. I have already tried: Remove graphics card Remove one and/or all RAM sticks Disconnect everything non-essential, even hard drives Clear CMOS I have not yet tried to remove all components and tried to boot everything outside of the case, because I did not have the time to disassemble and bleed the water loop. However, I can confirm that nothing is stuck underneath the motherboard, not is any of those brass raisers touching the board where it should not. Specs: Gigabyte GA-970A-UD3 AMD FX6300 ATI HD7850 I think this should be enough for this issue.

  Read the article

• I want to replace a number with successive numbers, starting at 1 and going up.

  - by Pär-Magnus Green

  I'm aware that this is something people can easily program, but I'm not familiar with those things, so I was hoping there was an easier solution. I've edited a large database of questions, including sorting, and ended up getting all the question ID's mixed up. I'm trying to do this in Notepad++, but any other suggestions are welcome. I'm wondering if there's a way to search for a string (ex. "Question[any number]") and replace the numbers with first 1, then 2, et.c. For clarification, this is how one question looks like: TriviaBot_Questions[3]['Question'][63] = "Acronyms: What does WTT stand for?"; TriviaBot_Questions[3]['Answers'][63] = {"Want To Trade"}; TriviaBot_Questions[3]['Category'][63] = 7; TriviaBot_Questions[3]['Points'][63] = 1; TriviaBot_Questions[3]['Hints'][63] = {}; and the next question, as is now, is not followed by 64. It might be 245 or 1029, and regardless of which number it is, I want it replaced with "previous number + 1", basically.

  Read the article

• Western Digital HDD disappears and reappears in BIOS

  - by tbkn23

  I know many people asked about similar problems, but I have a very specific case where I can't understand what's going on... I have a 3TB Western Digital Caviar Green disk connected in my Desktop, that also has a seagate 1.5TB disk and 2 SSD drives (OCZ and Sandisk). After working fine for quite some time (probably more than a year), suddenly my Caviar Green drive disappeared from windows. I checked the BIOS, and it wasn't there either. I opened my PC, played with the connectors, power, etc, but nothing helped. Even tried switching connectors with those of the 1.5TB disk, and nothing changed, the 1.5TB seagate was there, but the 3TB WD was not. Ok, now for the strange part. I have another desktop at home, so I took out my 3TB drive, connected it there, and it worked fine! I copied the most important files out of it, and then made another attempt in the original desktop. Surprise! It now appeared in the BIOS and worked fine! I even ran the SMART test with the WD tools and it said everything was intact. It doesn't end here. After leaving it overnight in the original desktop, it disappeared again in the morning. I repeated the entire process, connecting it to the second desktop, and there it is again working fine. Now for my question... Whats going on? The disk seems to be appearing on/off in my original Desktop, while other drives there work fine. SMART test says the disk is fine. Any ideas? Is the disk defective and should be replaced? Or maybe there's a problem with the controller in the desktop? I'm using a Gigabyte GA-880GA-UD3H motherboard and tried connecting the drive to both bridges (SATA2 and SATA3 bridges). Thanks EDIT: Power options are set never to turn off hard drives:

  Read the article

• I just got a virus 6 mins ago, how? Situation.

  - by acidzombie24

  -Edit- for the people who say it isn't a virus. Norton does detect it as a virus, an icon was placed on my system tray and rkpg.exe is in my C: which was placed 6 min ago around the time my computer rebooted on its own causing me to lose data :@. Situation I on Windows XP, behind a Linksys router, I don't have DMZ on so nothing should be connecting to me. I had Firefox, MSN and Visual Studio opened. With C# I programmed a quick application to scan some pages with Internet Explorer. The site it was scanning was deviantART (which is pretty trustworthy), I doubt any banners there would hold a virus. I went to a suspicious site called freetxt.com but that was on Firefox and it didn't load the site. With an extra check I ping it and got this message "Ping request could not find host freetxt.com." The virus seems to be called braviax. Right now it brought up a message saying my computer may be infected? How on earth did it get in? I don't have uTorrent installed or any torrent or p2p applications. Nothing is installed on my computer that I haven't installed before and I know the exact time it installed because I see rkpg.exe on my C drive and my computer restarted on its own around the same time. For the previous 30 minutes actually the previous hour all I did was talk on MSN, not click any links (I went to freetxt on my own) and had that Internet Explorer thing running (which I programmed). How did it get in? I really doubt it came from a banner on deviantART and installed when I loaded the page with the webbrowser-control so something else may have happened? Is there any system defaults I should turn off? I have remote assistance off but even if it was on I shouldn't be infected due to the router not forwarding any ports?

  Read the article

• Gigabit network limited to 25MB/s by CPU. How to make it faster?

  - by netvope

  I have a Acer Aspire R1600-U910H with a nForce gigabit network adapter. The maximum TCP throughput of it is about 25MB/s, and apparently it is limited by the single core Intel Atom 230; when the maximum throughput is reached, the CPU usage is about 50%-60%, which corresponds to full utilization considering this is a Hyper-threading enabled CPU. The same problem occurs on both Windows XP and on Ubuntu 8.04. On Windows, I have installed the latest nForce chipset driver, disabled power saving features, and enabled checksum offload. On Linux, the default driver has checksum offload enabled. There is no Linux driver available on Nvidia's website. ethtool -k eth0 shows that checksum offload is enabled: Offload parameters for eth0: rx-checksumming: on tx-checksumming: on scatter-gather: on tcp segmentation offload: on udp fragmentation offload: off generic segmentation offload: off The following is the output of powertop when the network is idle: Wakeups-from-idle per second : 61.9 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 90.9% (101.3) <interrupt> : eth0 4.5% ( 5.0) iftop : schedule_timeout (process_timeout) 1.8% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.9% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.5% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) And when the maximum throughput of about 25MB/s is reached: Wakeups-from-idle per second : 11175.5 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 99.9% (22097.4) <interrupt> : eth0 0.0% ( 5.0) iftop : schedule_timeout (process_timeout) 0.0% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.0% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.0% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) Notice the 20000 interrupts per second. Could this be the cause for the high CPU usage and low throughput? If so, how can I improve the situation? The other computers in the network can usually transfer at 50+MB/s without problems. And a minor question: How can I find out what is the driver in use for eth0?

  Read the article

• IDE compatability with SATA image

  - by Ormis

  We had an old CNC machine's hard-drive fail recently. The hard-drive is an old 1275MB IDE (Seagate) and there were defiantly bad sectors on it. I was able to image the contents of the drive onto a drive in my computer before it became completely unusable (I used DD, replacing all bad sectors w/ 0s). After running a couple chdsks, the SATA drive will boot off of the image. This is great, but there's one problem. The CNC machine old and requires IDE, I've attempted to copy the currently booting image off of the SATA drive and onto IDE drives numerous times in numerous ways and every time I do so the machines return that a boot device cannot be found. Some other information: The file system is fat32, running windows 98 The SATA drive is an 80gb drive I have tried copying the image to three 20gb and two 80gb IDE drives I have checked the jumper on the back of the IDE drives when using them If anyone has any ideas, questions, suggestions, etc. please let me know. P.S. I would just put a fresh install of win98 on the machine if i had the installation media (so that's out of the question). And if it comes to it, this is my last week working here, so I'll leave that to my co-worker. EDIT: Also, I have tried using Clonezilla as well as straight up DD to copy the image to the IDE drives.

  Read the article

• Nginx load balancing and maintaining URLs

  - by Steve Klabnik

  I'm trying to use nginx as a load balancer, and it's working great. One problem, though. The load balancing box is at 123.123.123.123, and the backend box is 456.456.456.456. So I have this config: upstream backend { server 456.456.456.456; } server { listen 80; server_name 123.123.123.123; access_log off; error_log off; location / { proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_pass http://backend; } } This works great. I hit 123.123.123.123 in my browser, and the page comes up. But now the URL in the browser says http://456.456.456.456. Do I need to use a rewrite rule or something to keep the url correct? I don't want it to be different when going to different backed servers. None of the tutorials I've read have mentioned anything about this.

  Read the article

• computer fails to boot during/after POST for five or six boots, then works

  - by N13

  For the last few days, my computer has had issues booting. I've seen two different behaviors: The screen displays the graphics card information, then begins to list the RAM, hard drives, etc. At different points in this process (after the graphics info), the computer shuts off. After five or six attempts, it then boots normally. In roughly the same time frame, the computer freezes, and fails to boot. I think it boots successfully on the next attempt. I've also noticed that in some instances, the computer freezes on shutdown. It gets right to the point where it should shut off, but doesn't. I recently combined the best parts of two different machines into this one. I'm booting to GRUB, with Ubuntu 12.04, Linux Mint 11 and Windows Vista (unfortunately) as my OS options. It has an Enermax Modu82+ 525W power supply, and I've used an online calculator to determine that my load shouldn't exceed 400W. I even unplugged a hard drive, but that didn't help. I found the latest BIOS, patched it and checked the settings, but that didn't fix it. I'm fairly certain this issue didn't exist at first, but might have started when the power at my new apartment dropped for a second. The machine is plugged into a surge protector strip, but it's old and I've heard they lose effectiveness with age. Is a power dip as damaging as a spike? If something were damaged, why would it boot successfully after five or six attempts? It's almost like the BIOS or PSU need to be primed. The trouble with debugging is that there seems to be a "grace period" after shutdown where the issue doesn't present itself again. What should I try next?

  Read the article

• Ubuntu on VPS becomes unresponsive: BUG: soft lockup - CPU#0 stuck for 22s

  - by Bhante Nandiya

  We have a VPS running Ubuntu, on Xen. The problem is this, about once a day, for about 20-50 minutes, at a random time, the server becomes completely unresponsive to the outside world. After this period, it becomes responsive again, as if nothing had happened, it doesn't lose uptime, it doesn't restart. It just starts responding again as if it had been in suspended animation. These outages occur under conditions of non-exceptional memory and cpu, for example 70% mem, 5% cpu. I have stopped all non-essential services so the usage is very even. These outages don't particularly occur during times of increased memory/cpu (during daily tasks), they sometimes occur at times of very low cpu use (<2%), but in the past also occured during swapping. These blackouts have been occurring both under Ubuntu 12.04 LTS, and Ubuntu 14.04 LTS - no change at all (I upgraded Ubuntu specifically to see if it helped this problem). It is possible to log into our webhosts site, and use their administration console to see error messages from during this time. Presumably, these messages are from the Xen virtualization, the main message goes like this: BUG: soft lockp - CPU#0 stuck for 22s! [ksoftireqd/0:3] (repeats many times) SysRq : Emergency Sync (Sometimes this is the only message in the console) Others seen previously under different load situations include: BUG: soft lockup - CPU#0 stuck for 22s! [swapper/0:0] (repeated many times) or: INFO: rcu_sched detected stall on CPU 0 (t=15000 jiffies) (repeated many times with t getting bigger) From googling around I've tried various kernel parameters such as nohz=off and acpi=off to no avail. All tech support has said is that other Ubuntu installations are not suffering the same problem. Anyone got any ideas or experience with this problem?

  Read the article

• 100% uptime for a web application

  - by Chris Lively

  We received an interesting "requirement" from a client today. They want 100% uptime with off-site failover on a web application. From our web application's viewpoint, this isn't an issue. It was designed to be able to scale out across multiple database servers, etc. However, from a networking issue I just can't seem to figure out how to make it work. In a nutshell, the application will live on servers within the client's network. It is accessed by both internal and external people. They want us to maintain an off-site copy of the system that in the event of a serious failure at their premises would immediately pick up and take over. Now we know there is absolutely no way to resolve it for internal people (carrier pigeon?), but they want the external users to not even notice. Quite frankly, I haven't the foggiest idea of how this might be possible. It seems that if they lose Internet connectivity then we would have to do a DNS change to forward traffic to the external machines... Which, of course, takes time. Ideas? UPDATE I had a discussion with the client today and they clarified on the issue. They stuck by the 100% number, saying the application should stay active even in the event of a flood. However, that requirement only kicks in if we host it for them. They said they would handle the uptime requirement if the application lives entirely on their servers. You can guess my response.

  Read the article

• How to I configure open_basedir parameter under my Centos VPS?

  - by deltanovember

  The parameter can be seen here http://wordswithfriends.net/test.php open_basedir /var/www/vhosts/wor.wordswithfriends.net/wordswithfriends.net/:/tmp I'm trying to add PHP pear directories /var/www/vhosts/wor.wordswithfriends.net/conf is as follows -rw-r----- 1 root apache 6461 Jan 25 08:56 12959674170.16899500_httpd.include -rw-r----- 1 root apache 6461 Jan 31 06:52 12960111810.31860800_httpd.include -rw-r----- 1 root apache 6532 Jan 31 06:55 12964785250.54523600_httpd.include -rw-r----- 1 root apache 6532 Jan 31 07:01 12964788880.47252600_httpd.include -rw-r----- 1 root apache 6532 Jan 31 15:54 12965108850.92819600_httpd.include -rw-r----- 1 root apache 6652 Jan 31 21:32 12965206700.32285200_httpd.include Currently configured as follows grep base 12965206700.32285200_httpd.include php_admin_value open_basedir /var/www/vhosts/wor.wordswithfriends.net/httpdocs/:/tmp/:/usr/share/pear/:/local/PEAR/ php_admin_value open_basedir /var/www/vhosts/wor.wordswithfriends.net/httpdocs/:/tmp/:/usr/share/pear/:/local/PEAR/ php_admin_value open_basedir /var/www/vhosts/wor.wordswithfriends.net/httpdocs/:/tmp/:/usr/share/pear/:/local/PEAR/ php_admin_value open_basedir /var/www/vhosts/wor.wordswithfriends.net/httpdocs/:/tmp/:/usr/share/pear/:/local/PEAR/ Configured vhost.conf as follows <Directory /var/www/vhosts/wor.wordswithfriends.net/wordswithfriends.net> <IfModule sapi_apache2.c> php_admin_flag engine on php_admin_flag safe_mode off php_admin_value open_basedir "/var/www/vhosts/wor.wordswithfriends.net:/tmp:/usr/share/pear/local/PEAR" </IfModule> <IfModule mod_php5.c> php_admin_flag engine on php_admin_flag safe_mode off php_admin_value open_basedir "/var/www/vhosts/wor.wordswithfriends.net:/tmp:/usr/share/pear:/local/PEAR" </IfModule> </Directory> Restarted apache and the parameter is still the same. I'm not sure why my pear directories are not showing up. I'm using Plesk. Any help appreciated

  Read the article

< Previous Page | 148 149 150 151 152 153 154 155 156 157 158 159  | Next Page >