Search Results

Search found 16902 results on 677 pages for 'trade off'.

Page 153/677 | < Previous Page | 149 150 151 152 153 154 155 156 157 158 159 160  | Next Page >

• Computer making strange sound when turned on, ever since power outage

  - by Dot NET

  Recently we experienced a power outage, and the PC was off. However, once the power came back, I switched on the PC and heard a strange noise - almost as if the hard disk or fans were struggling to work. I can't really describe the sound, but it's a laboured, loud sound almost like a jack-hammer. This has been persisting ever since the power outage, however the noise stops after around 10 minutes or so, and doesn't start again until the computer is turned off and on again. At first I thought it had something to do with the HDD, but all my files are intact, chkdsk did not report any issues and performance is 100% unchanged, even in games (so the gfx card is fine, and so is the HDD most likely). My PC setup basically has around 3 cooling fans, but I'm not sure if it's one of these either as the noise actually stops after 10 minutes or so, and if I leave the PC on for 4 hours (for example) the noise never starts again. It's there solely when turning on the PC. I haven't got a UPS, and it's important to note that the computer was not on when the power went out - it was merely plugged in. I then promptly unplugged the PC once the power was out, and only plugged it in again when the power came back. Could it be the power supply? Unfortunately I can't open my tower as I would void the warranty. Are there any tests which I could carry out without voiding the warranty?

  Read the article

• ASUS laptop doesn't charge/use the battery after reinstalling Windows 7

  - by Stan

  I've done a clean install of Windows 7 x64 on an ASUS X501A laptop. The battery is detected and shows in the system tray as "plugged in, charging". However the charge level stays at 76% and if the AC cord is plugged out the laptop turns off. The laptop does not turn on without being plugged in either. Everything worked perfectly prior to reinstall. I've tried: Downloading and installing all the ASUS drivers, including the ATK ACPI driver Checking the BIOS - there do not seem to be any battery-related settings Flashing the BIOS to the latest version Uninstalling Microsoft ACPI-Compliant Control Method Battery in device manager as suggested on the internet Full power discharge/ATX reset as suggested by ASUS support: remove mains power charger, remove battery, press and hold power button for 10 seconds, reconnect battery and mains and turn on I have a feeling all this may have something to do with the EFI BIOS that comes on the laptop. During the reinstall I had to delete all partitions and start anew, because the Windows installer complained about the improper order of GPT partitions. The EFI System Partition was recreated by the installer, and I am guessing that it may be missing the particular ACPI driver needed to make the battery work. I've tried researching this, but could not come up with any useful info. I am hoping someone here may know a bit more about this and maybe help me understand what's going on and how to fix it. Barring that, I'll have to re-image the drive off an identical ASUS laptop with stock install and hope it fixes things.

  Read the article

• Dell laptop keyboard doesn't work

  - by Tam

  I'm trying to fix my in-laws laptop, it's a Dell Studio 1745 that's running Windows 7 64 bit. The problem is that most of the keys on the keyboard do not work. The function keys work and the caps lock and numpad keys work, but no other keys do. If I hit the F2 key enough times when starting up, I can get to the BIOS, but after that even the function keys stop working. If I let it go all the way to the Windows login screen, I can see that the caps lock and num lock work - little images on screen actually appear, but they don't toggle the state of the key, i.e.,capslock is always off, numlock is always off. Using the fn+function combo works, so changing the brightness, etc. works fine. I'm stumped. I've tried disconnecting power and battery and leaving it for an hour or so before starting up but that hasn't helped either. Also - this might be a red herring - the touchpad is failing as well, the MS Device Manager says that it's failing with status 10, "unable to start device"

  Read the article

• reverse proxying with NGINX to two back-end servers

  - by aag

  I am trying to learn how to configure the Nginx proxy. All requests from external (www.external.com) should go to internal server 10.10.10.16:2080, except for www.external.com/nagios requests, which should go to internal 10.10.10.18. My location block looks as follows: location ~* / { proxy_buffers 16 4k; proxy_buffer_size 2k; proxy_buffering off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header Accept-Encoding ""; proxy_pass http://10.10.10.16:2080; } # # nagios server location ~* /nagios/ { proxy_buffers 16 4k; proxy_buffer_size 2k; proxy_buffering off; # proxy_set_header Host $host; # proxy_set_header X-Real-IP $remote_addr; # proxy_set_header Accept-Encoding ""; proxy_pass http://10.10.10.18; } The first location seems to work fine. However, any request to www.external.com/nagios sends the browser into the eternal pastures. Of course, 10.10.10.18/nagios was tested and works fine. What am I missing?

  Read the article

• lenovo x1 carbon windows 8 frequent wifi disconnect issue

  - by hIpPy

  I'm having frequent wifi disconnects on my Lenovo X1 Carbon Touch laptop. I got this laptop 2 months back and it has been happening ever since about 3-5 times a day and 10 times a week on average. I've Frontier Fios internet. Power connected or not does not matter. Once I get disconnected, I try below to connect again in that order: turn Airplane mode on and off, troubleshoot network problems windows troubleshooter), restart the laptop I'd find that the WiFi adapter would get disabled and sometimes windows troubleshooting would help but more than often I'd end up restarting the laptop. A week back, I upgraded my wifi network adapter drivers (now Intel, version 15.5.6.48, 10/3/2012). I still get disconnected frequently but turning Airplane mode on and off gets me connected again. So the driver update did help. Windows 8 is updated. None of the other devices (nexus, iphone phones, nexus7, ipad tablets) would have wifi issues when my laptop would get disconnected. config: Intel(R) Centrino(R) Advanced-N 6205 (WiFi network adapter) Microsoft Windows 8 Pro Microsoft Windows [Version 6.2.9200] x64-based PC LENOVO System Model: 3443CTO X1 Carbon Touch I recently noticed this log message When I got disconnected in event viewer: Your computer was not assigned an address from the network (by the DHCP Server) for the Network Card with network address 0x[XXXXXXXXXXXX]. The following error occurred: 0x79. Your computer will continue to try and obtain an address on its own from the network address (DHCP) server. Any idea?

  Read the article

• Httpd and LDAP Authentication not working for sub-pages

  - by DavisTasar

  I just recently installed a Nagios implementation, and I'm trying to get LDAP authentication working for httpd on Red Hat. (nagios.conf for Apache config below, sanitized of course) ScriptAlias /nagios/cgi-bin "/usr/local/nagios/sbin" <Directory "/usr/local/nagios/sbin"> #SSLRequireSSL Options ExecCGI AllowOverride none AuthType Basic AuthName "LDAP Authentication" AuthLDAPURL "ldap://my.domain.controller:389/OU=Users,DC=my,DC=domain,DC=controller?sAMAccountName?sub?(objectClass=user)" NONE AuthzLDAPAuthoritative off AuthLDAPBindDN "CN=NagiosAdmin,DC=my,DC=domain,DC=controller" AuthLDAPBindPassword "myPassword" require valid-user </Directory> Alias /nagios "/usr/local/nagios/share" <Directory /usr/local/nagios/share> #SSLRequireSSL Options None AllowOverride none AuthBasicProvider ldap AuthType Basic AuthName "LDAP Authentication" AuthzLDAPAuthoritative off AuthLDAPURL "ldap://my.domain.controller:389/OU=Users,DC=my,DC=domain,DC=controller?sAMAccountName?sub?(objectClass=user)" NONE AuthLDAPBindDN "CN=NagiosAdmin,DC=my,DC=domain,DC=controller" AuthLDAPBindPassword "myPassword" require valid-user </Directory> Now, the initial authentication works, so when you first hit the page you can log in just fine. However, when you go anywhere else, it prompts you for authentication, fails (asking for a re-prompt), and gives this error message: [Mon Oct 21 14:46:23 2013] [error] [client 172.28.9.30] access to /nagios/cgi-bin/statusmap.cgi failed, reason: verification of user id '<myuseraccount>' not configured, referer: http://<nagiosserver>/nagios/side.php I'm almost certain its a simple flag or option, but I just can't find it, and I don't have a lot of experience working with Apache. Any assistance or help would be greatly appreciated.

  Read the article

• Windows 7 Taskbar resets on every login

  - by Arne Mertz

  I like to reorder my Taskbar a bit, other than the Windows 7 default is. I use two "rows", the lower is for quicklaunch and other toolbars: This works perfectly, as long as I don't log off from the computer. Every time I log in, Windows 7 has messed up/reset the toolbar positions like this: So I have to drag them into position again and again, every morning. Fixing the taskbar positions won't help, I tried to google for the problem but it does not seem to be very common. Does anyone recognize that problem and has a solution? Update: This is not the AutoLogon bug. AutoLogon is off. We have installed Novell at our company, and it does not matter wether I log directly onto the Novell network or only to the computer first and to Novell later. Update2: I get the same issue when I logon without Novell, i.e. when I log on only to the computer. When I boot in safe mode, the taskbar looks essentially the same: Update3: KB979155 says it's "not applicable to my system". Creating a neew user is not an option since I don't have the admin privileges to do that - I have almost any other local admin privileges, though.

  Read the article

• Apache using 100% CPU, once again

  - by CBenni

  Recently, apache2 started using 100% of CPU power: top gives me From other, similar threads, I took the tip to use mod_status. Aside from HUGE amounts of NULL requests, it gives: CPU Usage: u2.16 s1.32 cu0 cs0 - .0835% CPU load 1.2 requests/sec - 17.6 kB/second - 14.6 kB/request 8 requests currently being processed, 42 idle workers The access and error logs do not show anything surprising or intriguing at all. Note the .8% CPU usage. Another tip was to use strace: root@server:~# strace -p 1956 Process 1956 attached - interrupt to quit restart_syscall(<... resuming interrupted call ...> And remains like this for at least half an hour, without producing any additional output. Restarting apache fixed the problem for less than a second The server runs a few custom python scripts aswell as a django-powered website on apache2 (up-to-date), but even turning the scripts off (or not having them active in the first place) did not change anything. After I stopped apache and powered my server off, powered it on a few minutes afterwards and restarted all my services, the CPU usage remained low for several hours, just in order to pop up again randomly (?) The DigitalOcean CPU stats on my server are: You can see how the CPU usage was super high for almost half a day until I restarted the bot - just to remain stable for several hours and then pop up again. I am completely at a loss of words and don't know what I could do to find out what piece of my code is giving me these problems or if apache itself is the cause... Therefore I would greatly appreciate any hints to the questions: What else can I try to do? Which things might I not have checked? Is this definitely in my own code? How do you find what part of python code crashes an app via a infinite loop or similar?

  Read the article

• Audio server with best API?

  - by Wintermute

  I'm a web dev, working in a small studio with a couple of other devs and some crayon-munchers (or, "designers"). Like all the best and trendiest creative studios, we have tunes. Our tunes consists of a set of speakers that whoever wants to can plug into their machine, and DJ their little socks off via iTunes, Spotify, VLC or whatever their music player of choice happens to be. Obviously, this lacks finesse. What we WANT is this: a single, dedicated machine running some sort of audio player (ideally Win-based, but a Linux flavour isn't impossible), that exposes an API. We (ie: me and the other devs) want to write a web-based client onto it, that'll let us remotely do all sorts of funky stuff like generating on-the-fly genre-based playlists, and voting for tracks, and making tea. My question - and please forgive me if this isn't the place for such a question, I was going to ask on Stackoverflow but that didn't seem right either - is this: what's the best player to start with? What can do all of this? I know VLC can function as a streaming server, but know nothing of any API it may have. I'd rather chop my pinky off than use iTunes, but if it does what we want, then... Anyhow, thanks for reading. All comments and suggestions gratefully received.

  Read the article

• Dual hard drive Windows 7 system, modified the registry to get programs to install on second drive, now IE doesn't work

  - by paul

  I have a dual hard drive Windows 7 system, Windows is installed on an SSD (C:) and I modified the registry to try to force programs to install on second HDD drive (another letter). The registry edits are pretty simple, just a few keys in HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion to change the drive letter. For the most part the system is very fast and works great, but IE doesn't work anymore. With IE10, it opens for a flash with a white window then closes. I tried installed IE11 which opens a white window for a few seconds, doesn't respond, then crashes. I've tried all the solutions I could find. This includes resetting the IE settings, "uninstalling" and re-installing IE, which is just turning it on and off in "Turn Windows Features on or off", copying the Program Files\Internet Explorer files onto both/either drives, changing the registry keys back to use C:, lots of rebooting, and safe mode. Nothing has worked. I don't see errors in the event viewer, but I might not know what to look for. Any ideas on how to get IE running? I don't need IE for daily browsing, I just need it for cross-browser testing on sites I build and on the rare occasion a page only works in IE. I don't really want to use a virtual machine, but would be ok with something standalone like tredosoft's, but I'm not aware of something like that for current versions of IE.

  Read the article

• ubuntu suspend works, but then immediately starts

  - by Yoav Aner

  Having a strange problem after upgrading from Ubuntu 11.04 to 12.04. Previously I could suspend just fine, the computer will switch itself off. Pressing the ON button will switch it on and it will resume. After upgrading to 12.04 however, when I suspend it does (almost) the same, turns itself off, but about 2 seconds later, the computer turns itself on again, and it goes back to life from suspend. I haven't changed any of the hardware or BIOS and it was working before just fine. Also tried every possible switch of pm-suspend ; setting acpi_sleep=nonvs in /etc/default/grub and also this suggestion but nothing seems to make a difference... UPDATE: just tested suspend using the 12.04 liveCD and it was working perfectly fine... but when I boot normally it doesn't. ANOTHER UPDATE: After re-installing I noticed that I can suspend. However, after restoring my home folder - the strange suspend problem happens again. I then created a new user account. When I login to the other account I can suspend without a problem... So This seems specific to my account only. How/What can cause this in my own user settings?

  Read the article

• Getting dwl-g122 to work on ubuntu

  - by User1

  I have a USB WiFi adapter, D-Link dwl-g122. I'm running Ubuntu 10.4. My laptop has a built-in wireless card that is connecting fine to the router. I plug in the usb and it never really connects. Here are some details: iwconfig wlan1 IEEE 802.11bg ESSID:"\x0B\xE1..." Mode:Managed Frequency:2.457 GHz Access Point: Not-Associated Tx-Power=19 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on lshw -c network: *-network:1 description: Wireless interface physical id: 3 logical name: wlan1 serial: 00:13:46:8b:xx:xx capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=IEEE 802.11bg dmesg [ 1096.814176] wlan1: direct probe to AP xxx (try 1) [ 1096.820960] wlan1: direct probe responded [ 1096.820969] wlan1: authenticate with AP xxx (try 1) [ 1096.823790] wlan1: authenticated [ 1096.823869] wlan1: associate with AP xxx (try 1) [ 1096.827667] wlan1: RX AssocResp from xxx (capab=0x411 status=0 aid=1) [ 1096.827674] wlan1: associated [ 1142.590912] wlan1: deauthenticating from xxx by local choice (reason=3) lsmod|rt2 rt2500usb 19643 0 rt2x00usb 11260 1 rt2500usb rt2x00lib 32133 2 rt2500usb,rt2x00usb mac80211 238896 3 ath5k,rt2x00usb,rt2x00lib cfg80211 148725 4 ath5k,ath,rt2x00lib,mac80211 led_class 3764 3 ath5k,rt2x00lib,sdhci It looks like the driver loads but it doesn't feel like connecting. The behavior is identical even if I blacklist the other wifi card (using an ath5k driver). It's almost like it is using the wrong password or something. Does anyone know what is happening? Is anyone using Ubuntu successful?

  Read the article

• Allowing directory view/traversal for a specific VirtualHost in Apache 2.2

  - by warren

  I have the following vhost configured: <VirtualHost *:80> DocumentRoot /var/www/myvhost ServerName myv.host.com ServerAlias myv.host.com ErrorLog logs/myvhost-error_log CustomLog logs/myvhost-access_log combined ServerAdmin [email protected] <Directory /var/www/myvhost> AllowOverride All Options +Indexes </Directory> </VirtualHost> The configuration appears to be correct from the apachectl tool's perspective. However, I cannot get a directory listing on that vhost: Forbidden You don't have permission to access / on this server. Additionally, a 403 Forbidden error was encountered while trying to use an ErrorDocument to handle the request. The error log shows the following: [Wed Mar 07 19:23:33 2012] [error] [client 66.6.145.214] Directory index forbidden by Options directive: /var/www/****** update2 More recently, the following is now kicking-into the error.log: [Wed Mar 07 20:16:10 2012] [error] [client 192.152.243.233] Options FollowSymLinks or SymLinksIfOwnerMatch is off which implies that RewriteRule directive is forbidden: /var/www/error/noindex.html update3 Today, the following is getting kicked-out: [Thu Mar 08 14:05:56 2012] [error] [client 66.6.145.214] Directory index forbidden by Options directive: /var/www/<mydir> [Thu Mar 08 14:05:56 2012] [error] [client 66.6.145.214] Options FollowSymLinks or SymLinksIfOwnerMatch is off which implies that RewriteRule directive is forbidden: /var/www/error/noindex.html [Thu Mar 08 14:05:57 2012] [error] [client 66.6.145.214] Request exceeded the limit of 10 internal redirects due to probable configuration error. Use 'LimitInternalRecursion' to increase the limit if necessary. Use 'LogLevel debug' to get a backtrace. This is after modifying the vhosts.conf file thusly: <VirtualHost *:80> DocumentRoot /var/www/<mydir> ServerName myhost ServerAlias myhost ErrorLog logs/myhost-error_log CustomLog logs/myhost-access_log combined ServerAdmin admin@myhost <Directory "/var/www/<mydir>"> Options All +Indexes +FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> What is missing? update 4 All subdirectories of the root directory do directory listings properly - it is only the root which cannot.

  Read the article

• Stop Windows 7 from accessing or writing to hard drive unless "told" to by me? (More info inside...)

  - by Jeff

  A confusing question, perhaps, but bear with me. I have two internal HDDs set up in a RAID0 array which I use as mass storage. I access the drive very infrequently (once a day at most) and so I have set up Windows 7's power options to turn off idle disks after only 1 minute. This is fine, and the disks are turned off most of the time. However, I notice that Windows sometimes spins up the drives when I really, really don't want or need it to. This causes a 30 second delay as both drives spin up and lock up my system. Some examples of when this happens: 1) When I'm installing something using Windows Installer or Installshield; it seems to me as if they're using the drive with most available free space as the installer cache location... so my big RAID drive has to spin up! Most annoying. 2) Apparently, when I open a Java-based program which resides on my system drive and has nothing to do with my RAID drive! 3) At boot-up and shut-down time. At shutdown the drive spin up only for the computer to immediately shut down! Incredibly frustrating! I've already tried changing the letter of the drive, and at some points have removed the drive letter entirely, which solves the first two issues above. So my question (FINALLY!) is this: is there any way I can mark this drive as being for "storage only", so Windows basically does not see it at all until I actually invoke it somehow? Or is there any way I could set it up so that only specific programs have write access to it? For example, download managers, TeraCopy, etc. etc.? Basically I want it to be a "ghost drive" until I'm ready to use it and to stop Windows from spinning it up all the damn time! Thank you. :)

  Read the article

• Slower/cached Linux file system required

  - by Chopper3

  I know it sounds odd but I need a slower or cached filesystem. I have a lot of firewalls that are syslog'ing their data to a pair of Linux VMs which write these files to their 'local' (actually FC SAN attached) ext3-formatted disks and also forward the messages to our Splunk servers. The problem is that the syslog server is writing these syslog messages as hundreds, sometimes thousands, of tiny ~4k writes per second back to our FC SAN - which can handle this workload right now but our FW traffic's going to be growing by at least a factor of 5000% (really) in coming months and that'll be a pain for the SAN, I want to fix the root cause before it's a problem. So I need some help figuring out a way of getting these writes cached or held-off in some way from the 'physical' disks so that the VMs fire off larger, but less frequent, writes - there's no way of avoiding these writes but there's no need for it to do so many tiny ones. I've looked at the various ext3 options, setting noatime and nodiratime but that's not made much of a dent in the problem. Obviously I'm investigating other file systems but thought I'd throw this out in case others have the same problem in the future. Oh and I can't just forward these messages to Splunk, our firewall team insist they're in their original format for diag purposes.

  Read the article

• Windows 7 doesn't start anymore

  - by 0xFF

  I've experienced some BSOD on windows 7 RC, and some freezing when startup, but today was big surprise, it doesn't start anymore. I tried to start on safe mode and no results too, it shows the starting animation, then a blue screen for less than a second and turns off immediately. The only thing I remember did today is update flash player under Firefox, then chrome stopped working even after logging off, and once restarting, it doesn't start anymore. Anyone experienced the same issue? any hints? [EDIT 3] Solved : Windows 7 have a very smart repair strategy, it works automatically, and it tried every possible fix, what fixed my problem was the system restore to a previous date, all this happened automatically. [EDIT2] these are the last lines in the ntbtlog.txt file Did not load driver \SystemRoot\System32\drivers\vga.sys Loaded driver \SystemRoot\System32\Drivers\NDProxy.SYS Did not load driver \SystemRoot\System32\Drivers\NDProxy.SYS Did not load driver \SystemRoot\System32\Drivers\NDProxy.SYS Did not load driver \SystemRoot\System32\Drivers\NDProxy.SYS Did not load driver \SystemRoot\System32\Drivers\NDProxy.SYS Loaded driver \SystemRoot\system32\drivers\CHDRT32.sys Loaded driver \SystemRoot\system32\DRIVERS\VSTAZL3.SYS Loaded driver \SystemRoot\system32\DRIVERS\VSTDPV3.SYS Loaded driver \SystemRoot\system32\DRIVERS\VSTCNXT3.SYS Loaded driver \SystemRoot\system32\drivers\modem.sys Loaded driver \SystemRoot\system32\DRIVERS\usbccgp.sys Loaded driver \SystemRoot\System32\Drivers\usbvideo.sys [edit] this is the BSOD I get : http://twitpic.com/i87cx Thank you.

  Read the article

• Hibernation fails; The system cannot find the file specified

  - by GMMan

  Recently I installed Ubuntu 12.04.1 LTS on my Lenovo Y480. Hibernation was working properly after the Ubuntu install, but I was making sure all of the operating systems on my system worked, including OneKey Recovery (recovery partition). It is of note that I installed Windows 7 from scratch with a disk image I downloaded off of my university's DreamSpark program, and further to that I had to image the partition with Paragon Backup & Recovery, repartition to convert the Windows partition to extended, install Ubuntu, and then restore the image. During that process I also used the Windows disc to edit the BCD as to reuse the existing entry for the restored partition. I also used the automated "repair your computer" option. With verification, I noticed that the "repair your computer" option actually wrote to the wrong BCD (the recovery partition), and I mounted the partition and restored the original BCD (from a copy I made earlier), and rebooted. At this point my GRUB broke, and I was able to restore it. At this point hibernation broke. I tried powercfg /h off and powercfg /h on, rebooted, and nothing. Also tried increasing the hibernation file size as directed on this post, but it still doesn't work. Executing shutdown /h yields The system cannot find the file specified.(2). What file? It seems that mounting the system partition sometimes works, but I don't want to keep it mounted in case it gets written to accidentally. How do I permanently fix this?

  Read the article

• 100% CPU when doing 4 or more concurrent requests with Magento

  - by pancake

  Currently I'm having trouble with a server running Magento, it's unbelievably slow. It's a VPS with a few Magento installations on it used for development, so I'm the only one using them. When I do 4 request all 2 seconds after each other I'm finished in 10 seconds. Slow, but still within the limits of my patience. When I do 4 "concurrent" requests, however (opening 4 tabs in a row, very quickly) all four cores go to 100% and stay there for like a minute. How is this possible? I know that there are a lot of possibilities here, so any tips on how to make an Apache/PHP server go faster are also welcome. It used to go a lot faster before, and I've also tried APC, but it kept causing problems (PHP errors, something with memory pools) so I've disabled it. By the way, the Magento cache is off and compiling is also off. I know this makes Magento slower than usual, but I don't think a 60 second response time is normal for any Magento installation. Virtual hardware: 4 Cores and 4096MB RAM Swap is never used (checked with htop) 100GB disk space, of which 10% is in use Software: Debian 6 DirectAdmin and apache custombuild PHP 5.2.17 (CLI) If you need more info, please tell me how to get it, because I probably don't know how. I do know how to use the command line in linux and the usage of quite a few commands, but my experience with managing a server is limited.

  Read the article

• Embedded Windows XP

  - by Kyle

  My company acquired a brake press for bending large structural steel plates. We received it second hand and it came with an embedded copy of windows XP. Now for the part that's driving me nuts: plug and play has been turned off, also accessibility options has been disabled. What does this mean for me? Keyboards will not work! Nothing that plugs into a USB port will work and it does not have a CD ROM drive. I have tried to turn on plug and play using the on screen keyboard but it is not there since accessibility options is turned off. I would just get an updated copy of the the embedded OS but they come from Sweden and are extremely expensive. I assume there has got to be a way to get a USB devices to work. We need to get a wifi adapter on it so I can use team viewer and remotely configure it for our needs. Things to keep in mind: There is no keyboard so everything has to be done with the mouse There is no PS2 port for a keyboard just a mouse. Odd. I am 5 states away from this location and have been working with a tech who is physically installing the machine. System 32 seems to be missing A LOT of files, the tech told me there is only 8 folders in there and no other files (I don't even understand how Windows is running like this). If anyone has ANY ideas I would appreciate it, I am unsure where to go from here.

  Read the article

• How do I prevent my computer from freezing when it starts to swap?

  - by cdauth

  I work as a Java programmer, so I often have to run several programs at the same time that consume a lot of memory. When my memory is full and Linux starts swapping, my computer almost completely freezes. I can see that it is heavily writing on the hard-disk and everything reacts really slowly, often not at all. Moving the mouse in X sometimes doesn’t work at all, sometimes it has a delay of several seconds, clicking usually has a delay of several minutes. Sometimes it is possible to change to the TTY (with a long delay), there I can usually type without delay, but when I try to log in, it takes several minutes after typing in the user name until the password prompt appears, and usually an error message appears that tells me that the login timed out. So the only possibility is usually to restart the computer. I noticed that other intensive writing to the hard disk also significantly slows down my computer. Sometimes, I used rsync to limit the bandwidth when I copied files around on my own computer, as else the system would be almost unusable. How can this be? At the moment it seems more useful to me to completely turn off swapping. That might crash some processes, which is unfortunate, but the alternative at the moment is to crash all processes by turning off my computer. I am using Gentoo Linux with kernel 3.6.2-gentoo, I have a 10 GB swap partition on a HDD.

  Read the article

• Are there any other causes of this error that are NOT related to initial setup?

  - by LordScree

  I'm trying to diagnose an issue at a customer site. They are receiving the following error: A network-related or instance-specific error occurred while establishing a connection to SQL Server I've seen this a few times, but only during the initial setup - it's often caused by one of the following: The database server is turned off The network connection between the database server and the application is closed or somehow blocked (e.g. a firewall) The SQL Server instance is not set up to receive remote connections from the application server (e.g. TCP is turned off, remote connections are disabled, or the "SQL Server Browser" service is stopped/disabled) However, if I assume that no configuration changes have been made, I'm trying to postulate on what the reason might be for getting this error at a random point after the initial setup. My initial thought is: SQL Server machine has run out of resources (e.g. RAM) and is unable to accept new requests from the application server Is this a valid theory? What other possible causes are there of this error that are not related to the initial setup of the server / application connection? Or is it simply impossible that this error could occur without a configuration change having been made (either on the SQL Server side, application side, or somewhere in-between (network))? NOTE: I believe this question differs from the plethora of questions related to this error message because the application and server have been talking to each other quite happily until now (most, if not all, other questions seem to relate to initial setup).

  Read the article

• Windows 7 automatically logs out when logging in

  - by Luke

  A Windows 7 HP x64 computer is set to automatically log in (no password), but once it starts logging in, it starts to load the desktop after the welcome screen, but before icons or background images are loaded, it goes to the Welcome screen saying 'Logging Off'. I can log in with Safe Mode, and I ran a couple different virus scans, with no detections. I also tried checking the userinit.exe file in System32 (as suggested by MANY users for Windows XP), but it's the same version as a working system. I also checked the registry under HKLM\Software\Microsoft\Windows NT\CurrentVersion\Winlogon for the SHELL and UserInit values, but they look normal. I tried to disable all startup items (through MSCONFIG) to select Diagnostic boot, but then I get a blue screen about the video driver not loading. Any other ideas? EDIT I created a new user, and it could log in no problems. I am thinking it's the NTUSER.DAT file. I just renamed it to NTUSER.DAT.old, then tried logging in as the problem user. I could log in, but as a TEMP profile. His profile folder is now C:\Users\TEMP, and his old folder is still accessible but in the wrong location. EDIT 2 I can't seem to turn off the TEMP profile, so I'm open to other suggestions. Copying the folders (i.e. Documents, Music, etc) does not work, as it creates an additional TEMP.000 then TEMP.001 folder each time the user logs in.

  Read the article

• Hard drive causing BSOD

  - by JoshIrving

  I've come across a problem after building my new PC and installing a clean Windows 7. I originally planed on a RAID 1 or 0 but after further research I decided against it. So I was left with two 1TB Western Digital Black SATA 6Gb/s hard drives. My plan now was to use my second hard drive as a backup (using Windows Backup or 3rd party software). I set both hard drives to AHCI in the BIOS and installed Windows 7. I went through the lengthy process of downloading and installing each driver manually (latest versions), using the motherboard disk for a list of what I need. After a few restarts and before installing any software, I took an image backup onto DVD and the second hard drive. First witnessed the problem during the first scheduled Windows backup. The progress bar froze at about 70% (doc backup done, image backup in progress). It stayed still for 2 hours until it blue screened. Next time the backup froze, I tried shutting down. It logged me out and got stuck at the last step ("Shutting down" and blue spinner) for an hour, until I hard shutdown. I later realised this hasn't got anything to do with the backup. I ended up blue screening on almost every shut down (same place). Turns out, it's because of the second hard drive spinning down or turning off. The computer will now shutdown properly, as long as I remember to read or write to the second drive before executing shutdown. I've now set "Turn off hard disk after: Never" - No problems, so far. Do I have dodgy hard drive(s) or should I investigate the POWER_STATE_DRIVER_FAILURE BSOD - can it be a driver issue? AHCI?

  Read the article

• Is my motherboard failing, or is there some other issue?

  - by ThatGuy

  So, several months ago I put together my own desktop PC. I set up a dual boot to Windows and Ubuntu. Recently, without changing any settings or installing anything new, the wifi stopped working on windows (I use a wifi adapter). It said it was connected, Network settings showed that it was working and running trouble shooting had no results. My internet still works on any other device. I found that removing the adapter from the motherboard and plugging it back in was the only thing that fixed the problem. Reinstalling the wifi drivers did not help. I purchased a new Wifi adapter, but the problem persists. More recently, I had a much more discouraging development. Sometimes, turning on the computer results in a boot loop: BIOS never starts. Instead, the monitor turns on as if it got a signal, then immediately turns off. This loops on it's own indefinitely until I hold down power, hard reset it, and try again. Sometimes it works, sometimes it doesn't. I haven't tested much on the Ubuntu side. It appears that wifi works at least some of the time, but since I've had issues just getting to BIOS I'm not confident the issue is on the software side. I've also noticed issues with some of the USB ports no longer working, but that seems to be off and on. Finally, as of a few minutes ago, I booted to windows to discover that everything was running very slowly. Slow here is a relative word, but I have a Samsung 840 pro SSD and I'm used to applications running nigh instantly, and it was a solid 3 minutes before any of my applications would load. Anyway, my question is this: Is it likely that my motherboard is failing? Either way, what steps can I take to try and pin down the problem and figure out what to do?

  Read the article

• Does Google sometimes ignore "special" characters, possibly depending on your location or font type settings? [closed]

  - by RLH

  TLDR Google tends to ignore special characters in my search strings. Is there anything that I can do about it and is it, possibly, happening because Google makes certain assumptions based off of my default text-encoding settings and my location? I just posted this question over at StackOverflow. I had found a C preprocessor that I'd never seen before. As I should have done, I Googled it and tried to find out further information. I attempted various search terms which were all variations of "C Operator ##" (some times with and some times without the double-quotes.) Google didn't bring back anything of use so I posted my question on SO. As you can see from the comments, someone mentioned a search string (ironically one which I did try to search) and stated that I could have even hit the "I'm feeling lucky" button and have gotten my answer. The problem is I did search that, and the results that I received were far more basic and even after following the top results and searching the resulting pages, I could find nothing referencing the string "##". I'm not posting this question to complain but it does provide an empirical example of something I've seen before that really bugs me-- Google often ignores special characters in my search strings and the results are often useless. As a developer I often need to search for string values containing non-alphanumeric characters. Some characters (like the underscore or hyphen) can be used without trouble. However, other characters (such as the ampersand, carat, tilde and pound sign) are often ignored in my query strings. Is there a way to prevent this from happening so that I can get meaningful results from Google? NOTE I stay logged into Google and I live in the US. I wonder if Google detects some form of text-encoding setting or derives my results based off of certain, localized text-based assumptions. Regardless, I would like to for Google to search for what I give it. Is there anything that I can do to improve my results?

  Read the article

< Previous Page | 149 150 151 152 153 154 155 156 157 158 159 160  | Next Page >