Search Results

Search found 9137 results on 366 pages for 'pc bsd'.

Page 149/366 | < Previous Page | 145 146 147 148 149 150 151 152 153 154 155 156  | Next Page >

• Everytime i am trying to connect to my box using SSH, its failing not connecting

  - by YumYumYum

  From any other PC doing SSH to my Ubuntu 11.10,is failing. My network setup: Telenet ISP (Belgium) Fiber cable < RJ45 cable straight to Ubuntu PC Even the SSH is running: Other PC: retrying over and over $ ping 192.168.0.128 PING 192.168.0.128 (192.168.0.128) 56(84) bytes of data. From 192.168.0.226 icmp_seq=1 Destination Host Unreachable From 192.168.0.226 icmp_seq=2 Destination Host Unreachable From 192.168.0.226 icmp_seq=3 Destination Host Unreachable From 192.168.0.226 icmp_seq=4 Destination Host Unreachable $ sudo service iptables stop Stopping iptables (via systemctl): [ OK ] $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] Connection closed by 192.168.0.128 $ ssh [email protected] [email protected]'s password: Connection closed by UNKNOWN $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host Follow up: -- checked cable -- using cable tester and other detectors -- no problem found in cable -- used random 10 cables -- adapter is not broken -- checked it using circuit tester by opening the system (card is new so its not network adapter card problem) -- leds are OK showing -- used LiveCD and did same ping test was having same problem -- disabled ipv6 100% to make sure its not the cause -- disabled iptables 100% so its also not the issue -- some more info $ nmap 192.168.0.128 Starting Nmap 5.50 ( http://nmap.org ) at 2012-06-08 19:11 CEST Nmap scan report for 192.168.0.128 Host is up (0.00045s latency). All 1000 scanned ports on 192.168.0.128 are closed (842) or filtered (158) Nmap done: 1 IP address (1 host up) scanned in 6.86 seconds ubuntu@ubuntu:~$ netstat -aunt | head Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN tcp 0 1 192.168.0.128:58616 74.125.132.99:80 FIN_WAIT1 tcp 0 0 192.168.0.128:56749 199.7.57.72:80 ESTABLISHED tcp 0 1 192.168.0.128:58614 74.125.132.99:80 FIN_WAIT1 tcp 0 0 192.168.0.128:49916 173.194.65.113:443 ESTABLISHED tcp 0 1 192.168.0.128:45699 64.34.119.101:80 SYN_SENT tcp 0 0 192.168.0.128:48404 64.34.119.12:80 ESTABLISHED tcp 0 0 192.168.0.128:54161 67.201.31.70:80 TIME_WAIT $ sudo killall dnsmasq -- did not solved the problem -- -- like many other Q/A was suggesting this same --- $ iptables --list Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination $ netstat -nr Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 $ ssh -vvv [email protected] OpenSSH_5.6p1, OpenSSL 1.0.0j-fips 10 May 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 192.168.0.128 [192.168.0.128] port 22. debug1: Connection established. debug3: Not a RSA1 key file /home/sun/.ssh/id_rsa. debug2: key_type_from_name: unknown key type '-----BEGIN' debug3: key_read: missing keytype debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug2: key_type_from_name: unknown key type '-----END' debug3: key_read: missing keytype debug1: identity file /home/sun/.ssh/id_rsa type 1 debug1: identity file /home/sun/.ssh/id_rsa-cert type -1 debug1: identity file /home/sun/.ssh/id_dsa type -1 debug1: identity file /home/sun/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.8p1 Debian-7ubuntu1 debug1: match: OpenSSH_5.8p1 Debian-7ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.6 debug2: fd 3 setting O_NONBLOCK debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: [email protected],[email protected],[email protected],[email protected],ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: kex_parse_kexinit: ecdh-sha2-nistp256,ecdh-sha2-nistp384,ecdh-sha2-nistp521,diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss,ecdsa-sha2-nistp256 debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: mac_setup: found hmac-md5 debug1: kex: server->client aes128-ctr hmac-md5 none debug2: mac_setup: found hmac-md5 debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug2: dh_gen_key: priv key bits set: 118/256 debug2: bits set: 539/1024 debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug3: check_host_in_hostfile: host 192.168.0.128 filename /home/sun/.ssh/known_hosts debug3: check_host_in_hostfile: host 192.168.0.128 filename /home/sun/.ssh/known_hosts debug3: check_host_in_hostfile: match line 139 debug1: Host '192.168.0.128' is known and matches the RSA host key. debug1: Found key in /home/sun/.ssh/known_hosts:139 debug2: bits set: 544/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /home/sun/.ssh/id_rsa (0x213db960) debug2: key: /home/sun/.ssh/id_dsa ((nil)) debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-keyex,gssapi-with-mic,publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering RSA public key: /home/sun/.ssh/id_rsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug1: Authentications that can continue: publickey,password debug1: Trying private key: /home/sun/.ssh/id_dsa debug3: no such identity: /home/sun/.ssh/id_dsa debug2: we did not send a packet, disable method debug3: authmethod_lookup password debug3: remaining preferred: ,password debug3: authmethod_is_enabled password debug1: Next authentication method: password [email protected]'s password: debug3: packet_send2: adding 64 (len 60 padlen 4 extra_pad 64) debug2: we sent a password packet, wait for reply debug1: Authentication succeeded (password). Authenticated to 192.168.0.128 ([192.168.0.128]:22). debug1: channel 0: new [client-session] debug3: ssh_session2_open: channel_new: 0 debug2: channel 0: send open debug1: Requesting [email protected] debug1: Entering interactive session. debug2: callback start debug2: client_session2_setup: id 0 debug2: channel 0: request pty-req confirm 1 debug1: Sending environment. debug3: Ignored env ORBIT_SOCKETDIR debug3: Ignored env XDG_SESSION_ID debug3: Ignored env HOSTNAME debug3: Ignored env GIO_LAUNCHED_DESKTOP_FILE_PID debug3: Ignored env IMSETTINGS_INTEGRATE_DESKTOP debug3: Ignored env GPG_AGENT_INFO debug3: Ignored env TERM debug3: Ignored env HARDWARE_PLATFORM debug3: Ignored env SHELL debug3: Ignored env DESKTOP_STARTUP_ID debug3: Ignored env HISTSIZE debug3: Ignored env XDG_SESSION_COOKIE debug3: Ignored env GJS_DEBUG_OUTPUT debug3: Ignored env WINDOWID debug3: Ignored env GNOME_KEYRING_CONTROL debug3: Ignored env QTDIR debug3: Ignored env QTINC debug3: Ignored env GJS_DEBUG_TOPICS debug3: Ignored env IMSETTINGS_MODULE debug3: Ignored env USER debug3: Ignored env LS_COLORS debug3: Ignored env SSH_AUTH_SOCK debug3: Ignored env USERNAME debug3: Ignored env SESSION_MANAGER debug3: Ignored env GIO_LAUNCHED_DESKTOP_FILE debug3: Ignored env PATH debug3: Ignored env MAIL debug3: Ignored env DESKTOP_SESSION debug3: Ignored env QT_IM_MODULE debug3: Ignored env PWD debug1: Sending env XMODIFIERS = @im=none debug2: channel 0: request env confirm 0 debug1: Sending env LANG = en_US.utf8 debug2: channel 0: request env confirm 0 debug3: Ignored env KDE_IS_PRELINKED debug3: Ignored env GDM_LANG debug3: Ignored env KDEDIRS debug3: Ignored env GDMSESSION debug3: Ignored env SSH_ASKPASS debug3: Ignored env HISTCONTROL debug3: Ignored env HOME debug3: Ignored env SHLVL debug3: Ignored env GDL_PATH debug3: Ignored env GNOME_DESKTOP_SESSION_ID debug3: Ignored env LOGNAME debug3: Ignored env QTLIB debug3: Ignored env CVS_RSH debug3: Ignored env DBUS_SESSION_BUS_ADDRESS debug3: Ignored env LESSOPEN debug3: Ignored env WINDOWPATH debug3: Ignored env XDG_RUNTIME_DIR debug3: Ignored env DISPLAY debug3: Ignored env G_BROKEN_FILENAMES debug3: Ignored env COLORTERM debug3: Ignored env XAUTHORITY debug3: Ignored env _ debug2: channel 0: request shell confirm 1 debug2: fd 3 setting TCP_NODELAY debug2: callback done debug2: channel 0: open confirm rwindow 0 rmax 32768 debug2: channel_input_status_confirm: type 99 id 0 debug2: PTY allocation request accepted on channel 0 debug2: channel 0: rcvd adjust 2097152 debug2: channel_input_status_confirm: type 99 id 0 debug2: shell request accepted on channel 0 Welcome to Ubuntu 11.10 (GNU/Linux 3.0.0-12-generic x86_64) * Documentation: https://help.ubuntu.com/ 297 packages can be updated. 92 updates are security updates. New release '12.04 LTS' available. Run 'do-release-upgrade' to upgrade to it. Last login: Fri Jun 8 07:45:15 2012 from 192.168.0.226 sun@SystemAX51:~$ ping 19<--------Lost connection again-------------- Tail follow: -- dmesg is showing a very abnormal logs, like Ubuntu is automatically bringing the eth0 up, where eth0 is getting also auto down. [ 2025.897511] r8169 0000:02:00.0: eth0: link up [ 2029.347649] r8169 0000:02:00.0: eth0: link up [ 2030.775556] r8169 0000:02:00.0: eth0: link up [ 2038.242203] r8169 0000:02:00.0: eth0: link up [ 2057.267801] r8169 0000:02:00.0: eth0: link up [ 2062.871770] r8169 0000:02:00.0: eth0: link up [ 2082.479712] r8169 0000:02:00.0: eth0: link up [ 2285.630797] r8169 0000:02:00.0: eth0: link up [ 2308.417640] r8169 0000:02:00.0: eth0: link up [ 2480.948290] r8169 0000:02:00.0: eth0: link up [ 2824.884798] r8169 0000:02:00.0: eth0: link up [ 3030.022183] r8169 0000:02:00.0: eth0: link up [ 3306.587353] r8169 0000:02:00.0: eth0: link up [ 3523.566881] r8169 0000:02:00.0: eth0: link up [ 3619.839585] r8169 0000:02:00.0: eth0: link up [ 3682.154393] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 3899.866854] r8169 0000:02:00.0: eth0: link up [ 4723.978269] r8169 0000:02:00.0: eth0: link up [ 4807.415682] r8169 0000:02:00.0: eth0: link up [ 5101.865686] r8169 0000:02:00.0: eth0: link up How do i fix it? -- http://ubuntuforums.org/showthread.php?t=1959794 $ apt-get install openipml openhpi-plugin-ipml $ openipmish > help redisp_cmd on|off > redisp_cmd on redisp set Final follow up: Step 1: BUG for network card driver r8169 Step 2: get the latest build version http://www.realtek.com/downloads/downloadsView.aspx?Langid=1&PNid=4&PFid=4&Level=5&Conn=4&DownTypeID=3&GetDown=false&Downloads=true#RTL8110SC(L) Step 3: build / make $ cd /var/tmp/driver $ tar xvfj r8169.tar.bz2 $ make clean modules && make install $ rmmod r8169 $ depmod $ cp src/r8169.ko /lib/modules/3.xxxx/kernel/drivers/net/r8169.ko $ modprobe r8169 $ update-initramfs -u $ init 6 Voila!!

  Read the article

• How to create RPM for 32-bit arch from a 64-bit arch server?

  - by Gnanam

  Our production server is running CentOS5 64-bit arch. Because there are no RPM available currently for SQLite latest version (v3.7.3), I created RPM using rpmbuild the very first time by following the instructions given here. I was able to successfully create RPM for 64-bit (x86_64) architecture. But am not able to create RPM for 32-bit (i386) architecture. It failed with the following errors: ... ... ... + ./configure --build=x86_64-redhat-linux-gnu --host=x86_64-redhat-linux-gnu --target=i386-redhat-linux-gnu --program-prefix= --prefix=/usr --exec-prefix=/usr --bindir=/usr/bin --sbindir=/usr/sbin --sysconfdir=/etc --datadir=/usr/share --includedir=/usr/include --libdir=/usr/lib64 --libexecdir=/usr/libexec --localstatedir=/var --sharedstatedir=/usr/com --mandir=/usr/share/man --infodir=/usr/share/info --enable-threadsafe checking for a BSD-compatible install... /usr/bin/install -c checking whether build environment is sane... yes checking for gawk... gawk checking whether make sets $(MAKE)... yes checking for style of include used by make... GNU checking for x86_64-redhat-linux-gnu-gcc... no checking for gcc... gcc checking for C compiler default output file name... configure: error: C compiler cannot create executables See `config.log' for more details. error: Bad exit status from /var/tmp/rpm-tmp.73141 (%build) RPM build errors: Bad exit status from /var/tmp/rpm-tmp.73141 (%build) This is the command I called: rpmbuild --target i386 -ba sqlite.spec My question is, how do I create RPM for 32-bit arch from a 64-bit arch server?

  Read the article

• Is StoreJet Transcend (0x2329) an Advanced Format drive?

  - by Graham Perrin

  I use a 640 GB StoreJet Transcend (0x2329) with ZEVO Community Edition 1.1.1 on OS X 10.8.2. Question Is this drive Advanced Format? Background I submitted a request for technical support to Transcend but the first response was gibberish so I don't expect a reasonable follow-up. Models at http://www.transcend-info.com/Products/CatList.asp?LangNo=0&ModNo=293 are similar but different sizes (not 640 GB). Mine is probably 25M2 (TS640GSJ25M2): Unless I'm missing something, nothing currently in the Transcend support area tells me whether the drive is Advanced Format. From System Information in OS X 10.8.2: StoreJet Transcend: Capacity: 640.14 GB (640,135,028,736 bytes) Removable Media: Yes Detachable Drive: Yes BSD Name: disk3 Product ID: 0x2329 Vendor ID: 0x152d (JMicron Technology Corp.) Version: 0.00 Serial Number: 322549FBA004 Speed: Up to 480 Mb/sec Manufacturer: JMicron History for the ZFS pool shows creation in March 2012 –  macbookpro08-centrim:~ gjp22$ zpool history zhandy | grep create 2012-03-14.17:29:37 zpool create -f -O compression=off -O copies=1 -O casesensitivity=insensitive -O snapdir=visible zhandy /dev/dsk/GPTE_1928482A-7FE4-482D-B692-3EC6B03159BA 2012-06-22.15:51:16 zfs create zhandy/Pocket Time Machine At that time I almost certainly used ZEVO Setup Assistant to create the pool. macbookpro08-centrim:~ gjp22$ zpool get ashift zhandy NAME PROPERTY VALUE SOURCE zhandy ashift 0 default If I discover that the drive is Advanced Format, a different ashift value will be appropriate.

  Read the article

• What is the difference between the Linux and Linux LVM partition type?

  - by ujjain

  Fdisk shows multiple partition types. What is the difference between choosing 83) Linux and 8e) Linux LVM? Choosing 83) Linux also works fine for using LVM, even creating a physical volume on /dev/sdb without a partition table works. Does picking a partition type in fdisk really matter? What is the difference in picking Linux or Linux LVM as partition type? [root@tst-01 ~]# fdisk /dev/sdb WARNING: DOS-compatible mode is deprecated. It's strongly recommended to switch off the mode (command 'c') and change display units to sectors (command 'u'). Command (m for help): l 0 Empty 24 NEC DOS 81 Minix / old Lin bf Solaris 1 FAT12 39 Plan 9 82 Linux swap / So c1 DRDOS/sec (FAT- 2 XENIX root 3c PartitionMagic 83 Linux c4 DRDOS/sec (FAT- 3 XENIX usr 40 Venix 80286 84 OS/2 hidden C: c6 DRDOS/sec (FAT- 4 FAT16 <32M 41 PPC PReP Boot 85 Linux extended c7 Syrinx 5 Extended 42 SFS 86 NTFS volume set da Non-FS data 6 FAT16 4d QNX4.x 87 NTFS volume set db CP/M / CTOS / . 7 HPFS/NTFS 4e QNX4.x 2nd part 88 Linux plaintext de Dell Utility 8 AIX 4f QNX4.x 3rd part 8e Linux LVM df BootIt 9 AIX bootable 50 OnTrack DM 93 Amoeba e1 DOS access a OS/2 Boot Manag 51 OnTrack DM6 Aux 94 Amoeba BBT e3 DOS R/O b W95 FAT32 52 CP/M 9f BSD/OS e4 SpeedStor c W95 FAT32 (LBA) 53 OnTrack DM6 Aux a0 IBM Thinkpad hi eb BeOS fs e W95 FAT16 (LBA) 54 OnTrackDM6 a5 FreeBSD ee GPT f W95 Ext'd (LBA) 55 EZ-Drive a6 OpenBSD ef EFI (FAT-12/16/ 10 OPUS 56 Golden Bow a7 NeXTSTEP f0 Linux/PA-RISC b 11 Hidden FAT12 5c Priam Edisk a8 Darwin UFS f1 SpeedStor 12 Compaq diagnost 61 SpeedStor a9 NetBSD f4 SpeedStor 14 Hidden FAT16 <3 63 GNU HURD or Sys ab Darwin boot f2 DOS secondary 16 Hidden FAT16 64 Novell Netware af HFS / HFS+ fb VMware VMFS 17 Hidden HPFS/NTF 65 Novell Netware b7 BSDI fs fc VMware VMKCORE 18 AST SmartSleep 70 DiskSecure Mult b8 BSDI swap fd Linux raid auto 1b Hidden W95 FAT3 75 PC/IX bb Boot Wizard hid fe LANstep 1c Hidden W95 FAT3 80 Old Minix be Solaris boot ff BBT 1e Hidden W95 FAT1 Command (m for help):

  Read the article

• nmap installation issue

  - by daasf

  vanilla centos with latest updates, installed gcc, and after ./configure:.... Configuration complete. Type make (or gmake on some *BSD machines) to compile. [root@winxp nmap-5.51]# make Makefile:375: makefile.dep: No such file or directory g++ -MM -I./liblua -I./libdnet-stripped/include -I./libpcre -I./libpcap -I./nbase - I./nsock/include -DHAVE_CONFIG_H -DNMAP_NAME=\"Nmap\" -DNMAP_URL=\"http://nmap.org\" - DNMAP_PLATFORM=\"x86_64-unknown-linux-gnu\" -DNMAPDATADIR=\"/usr/local/share/nmap\" - D_FORTIFY_SOURCE=2 main.cc nmap.cc targets.cc tcpip.cc nmap_error.cc utils.cc idle_scan.cc osscan.cc osscan2.cc output.cc payload.cc scan_engine.cc timing.cc charpool.cc services.cc protocols.cc nmap_rpc.cc portlist.cc NmapOps.cc TargetGroup.cc Target.cc FingerPrintResults.cc service_scan.cc NmapOutputTable.cc MACLookup.cc nmap_tty.cc nmap_dns.cc traceroute.cc portreasons.cc xml.cc nse_main.cc nse_utility.cc nse_nsock.cc nse_dnet.cc nse_fs.cc nse_nmaplib.cc nse_debug.cc nse_pcrelib.cc nse_binlib.cc nse_bit.cc > makefile.dep /bin/sh: g++: command not found make: *** [makefile.dep] Error 127 [root@winxp nmap-5.51]# yum install g++ -y Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * addons: mirror.ash.fastserv.com * base: centos.mirror.choopa.net * extras: mirror.trouble-free.net * updates: mirror.nexcess.net Setting up Install Process No package g++ available. Nothing to do [root@winxp nmap-5.51]#

  Read the article

• File system concepts (df command)

  - by mkab

  I'm finding it difficult to understand some stuffs about the df command. Suppose I type df and I have the following output Filesystem 1k-blocks Used Avail Capacity Mounted on /dev/da0s1 some number some number number percentage /win /dev/da0s2 some number some number number percentage /win/home /dev/da0s3a some number some number number percentage / devfs some number some number number percentage /dev /dev/da0s3g some number some number number percentage /local /dev/da0s3h some number some number -number 102% /reste /dev/da0s3d some number some number number percentage /tmp /dev/da1s3f some number some number number percentage /usr /dev/da1s3e some number some number number percentage /var /dev/da1s1a some number some number number percentage /public Are the answers to the following questions correct? How many physical drives do I have? Ans: 2. da0s1 and da1s1 How many physical partitions on each disk? Ans: 8 for da0s1 and 1 for da1s1 How many BSD partition on each physical partition Ans: Impossible to determine. We have to use the -T to determine its type How is it possible for the file system /dev/da0s3h filled at 102%? And where is this overflowed data written?Ans: I have no idea for this one Thanks.

  Read the article

• Installing and running a guest OS on KVM-qemu with only serial console access

  - by nixnotwin

  I am trying to installing a bsd distro with virt-installer. With a Linux distro I used this: virt-install -n debian -r 1024 --vcpus=1 --accelerate -v --disk /var/kvm/installation-disks/debian.img,size=6--nographics --network=bridge:br0,model=ne2k_pci,mac=52:54:00:66:68:09 -l http://ftp.de.debian.org/debian/dists/squeeze/main/installer-amd64/current/images/ -x console=ttyS0,115200 This loads the installer directly from the online mirror. With Fedora I used this mirror: http://www.nic.funet.fi/pub/mirrors/fedora.redhat.com/pub/fedora/linux/releases/16/Fedora/x86_64/os/ Are there such mirrors for freebsd or openbsd? The reason I want direct installable ftp/http mirrors is because I can access my physical server only via ssh, and it doesn't have a X server or a window manager to give me a VNC GUI. When I tried installing centos 6 with an online mirror I was able to finish the installation via serial console, but after I rebooted it, the serial console never worked for me. I tried everything possible---editing menu.lst, inttab and securtty files. Fedora 16 booted fine from serial console, but got stuck when it loaded anaconda installer. I tried editing freebsd iso installation media by adding serial console option to boot option. And installation was successful. But couldn't boot into it becuase it wasn't giving console acess. I couldn't edit any files as ufs partition cannot be loaded with write access on my Ubuntu server 10.04. Only debian squeeze worked well, it worked for me even without editing a single configuration file. I want to have CLI versions of fedora/centos and freebsd/openbsd. But, looks like there isn't any hope for me to have them, as I have to depend on a serial console to do everything.

  Read the article

• Home Server: cpu virtualisation, what to choose?

  - by Huygens

  I'm looking for virtualisation solutions for storage and OS for a home server. A sort of private cloud where I manage the storage space independently of the VM one. This question focus on VM (or compute instance) management and what would best suit my needs. (I have another question related to the storage management). My use cases are: A backup server: rsync and other services running. A personal cloud server: a kind of owned dropbox system, à la ownCloud. " users foreseen. A media server: streaming videos and displaying photos. Here my environement and wishes: Server: HP Proliant MicroServer with 8 GB RAM (AMD Turion dual core with AMD-V technology) OS types: only Linux (perhaps a *BSD VM in the future) Linux distributions do not matter, I'm familiar with RHEL, Fedora, Suse, Ubuntu, but any other recommandation will be fine 2-3 VMs foreseen: backup server, owncloud server and media server (optional). Those are only servers, so no graphical console needed (I don't need VirtualBox) By VM I mean a virtualised environment like KVM, Xen, etc. or a compute instance like with OpenStack storage should be "virtualised/cloudified" see my other question. VM should be able to be migrated to another server in the future if performance cannot be fullfilled anymore by the current server It does not matter if installation of such setup is complicated as long as management tools allow for easy maintenance I don't have Windows at home, so solution should be Linux friendly and would be nice to be web based. But native apps are OK too. System should be easy to enhance: by adding a new server to migate some of the VMs to it. So it's really a kind of private cloud on which I could run some Linux OS. I would prefer free (libre, as in a free speach) and open source tools. But it does not have to be free as in a free beer. So Xen, KVM, VitualBox or OpenStack? What would you recommend?

  Read the article

• Linux drivers for laser printer Konica Minolta Magicolor 4750DN

  - by user51166

  I would like to install the konica minolta magicolor 4750DN in Linux (debian 64 bits, I know it's not really supported but that's not the issue right now) but all the manual says is "put the CD rom in and copy the drivers and PPD file". However I did not get the CD ! On their "fantastic" internet site (...) there are only available drivers for Windows and Mac OSX. I tried to extract the ppd file from the .dmg file for MacOSX 10.7 but, if the PPD file works, a compiled file (only mac compiled, MACH 4 architectures says the "file" command) does not (obviously "cannot execute binary file", since I'm trying to run a Mac file on Linux). Is there anybody who has the same printer that could lend me the Linux drivers on the CD ROM ? Couldn't find them anywhere on the internet. Any way to execute a Mach (or BSD) binary file on Linux (I don't think is possible, although some "emulators" may exist). Thank you very much. I buyed this printer even because it was advertised as "Linux compatible", only to get this bad surprise. I would be grateful if you could help me solve this problem.

  Read the article

• When connecting to PPTP Centos via Windows 7 VPN, I get error 2147943625

  - by Charlie Dyason

  The remote computer refused the network connection. phrase has been my arch enemy for the past week now I recently "bought" a VPS server, I gave up trying to configure it with OpenVPN, all the issues were making me lose my mind, so I tried the easier way with pptp, but i figure, both are leading to a dead end... I followed this post (many others too but this is the unlucky one), http://blog.secaserver.com/2011/10/install-vpn-pptp-server-centos-6/ and it all goes well with the setup, however, I run into this error when connecting to the VPN in Windows 7 here is a pic of the error: Image So I do not know what I have done wrong... When connecting, Code: Select all netstat -apn | grep -w 1723 before connecting: netstat -apn |grep -w 1723 tcp 0 0 0.0.0.0:1723 0.0.0.0:* LISTEN 1137/pptpd after the error came I tried again: netstat -apn |grep -w 1723 tcp 0 0 0.0.0.0:1723 0.0.0.0:* LISTEN 1137/pptpd tcp 0 0 41.185.26.238:1723 41.13.212.47:49607 TIME_WAIT - iptables: # Generated by iptables-save v1.4.7 on Fri Nov 1 18:14:53 2013 *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [63:8868] -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i eth0 -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m state --state NEW -m tcp --dport 22 -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --dport 1723 -j ACCEPT -A INPUT -i eth0 -p gre -j ACCEPT -A FORWARD -i ppp+ -o eth0 -j ACCEPT -A FORWARD -i eth0 -o ppp+ -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT # Completed on Fri Nov 1 18:14:53 2013 # Generated by iptables-save v1.4.7 on Fri Nov 1 18:14:53 2013 *nat : PREROUTING ACCEPT [96:12732] : POSTROUTING ACCEPT [0:0] : OUTPUT ACCEPT [31:2179] -A POSTROUTING -o eth0 -j MASQUERADE COMMIT # Completed on Fri Nov 1 18:14:53 2013 options.pptpd the only changes was the require-mppe # BSD licensed ppp-2.4.2 upstream with MPPE only, kernel module ppp_mppe.o # {{{ refuse-pap refuse-chap refuse-mschap # Require the peer to authenticate itself using MS-CHAPv2 [Microsoft # Challenge Handshake Authentication Protocol, Version 2] authentication. require-mschap-v2 require-mppe # Require MPPE 128-bit encryption # (note that MPPE requires the use of MSCHAP-V2 during authentication) require-mppe-128 # }}} I check the iptables, everything is normal, all INPUTs, etc are before rejects, username and password I also checked in chap-secrets file, I am really puzzled...

  Read the article

• Is execution of sync(8) still required before shutting down linux?

  - by Amos Shapira

  I still see people recommend use of "sync; sync; sync; sleep 30; halt" incantations when talking about shutting down or rebooting Linux. I've been running Linux since its inception and although this was the recommended procedure in the BSD 4.2/4.3 and SunOS 4 days, I can't recall that I had to do that for at least the last ten years, during which I probably went through shutdown/reboot of Linux maybe thousands of times. I suspect that this is an anachronism since the days that the kernel couldn't unmount and sync the root filesystem and other critical filesystems required even during single-user mode (e.g. /tmp), and therefore it was necessary to tell it explicitly to flush as much data as it can to disk. These days, without finding the relevant code in the kernel source yet (digging through http://lxr.linux.no and google), I suspect that the kernel is smart enough to cleanly unmount even the root filesystem and the filesystem is smart enough to effectively do a sync(2) before unmounting itself during a normal "shutdown"/"reboot"/"poweorff". The "sync; sync; sync" is only necessary in extreme cases where the filesystem won't unmount cleanly (e.g. physical disk failure) or the system is in a state that only forcing a direct reboot(8) will get it out of its freeze (e.g. the load is too high to let it schedule the shutdown command). I also never do the "sync" procedure before unmounting removable devices, and never hit a problem. Another example - Xen allows the DomU to be sent a "shutdown" command from the Dom0, this is considered a "clean shutdown" without anyone having to login and type the magical "sync; sync; sync" first. Am I right or was I lucky for a few thousands of system shutdowns?

  Read the article

• Best all in one linux based proxy,firewall, dhcp and wins server.

  - by BeStRaFe

  I help to run a lan in Sydney. We have a need for a proxy/gateway solution to allow those pesky games that require internet to work. I have been doing this with an ISA server and it has worked quite well. However now i wish to port this over to run on the same hardware as our cacti / nagios box under a vmware VM. ISA server is horridly nad due to the massive ram and i/o requirement for something is basically port blocking and handing out IP's. The needs are as follows. 1. DHCP 2. WINS (otherwise network devices fight over who is the WINS master) 3. Filtering based in PORT for outbound traffic. 4. Ability to whitelist IP/MAC's for internet access. 5. Web Interface. I had been thinking to use PFSENSE however there is no option for a WINS server and i cbf working my way around bsd.

  Read the article

• Windows Network File Transfer to Samba server: “Are you sure you want to copy this file without its properties?”

  - by jimp

  I am transferring a lot of files to a new NAS based on OpenMediaVault, with the Samba 3.5.6 service running. I am transferring from Windows 7 64-bit to the NAS, and on some media files Windows is prompting about losing some property data across the transfer. I have never seen this before when transferring to Samba boxes I have built myself (vs this turnkey solution), so I'm guessing there must be a Samba setting I can change to preserve the file properties in question instead of permanently losing whatever they contain (Date Taken? Exposure? Flash Fired? etc). Or maybe I've just never encountered this before; I'm really not sure. I tried adding ea support = yes and store dos attributes = yes to the [global] section, but the problem remains. The Linux file system is ext4 mounted with user_xattr (full options: defaults,acl,user_xattr,noexec,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0) as Samba requires. Any ideas would be greatly appreciated. Thank you! Samba config: [global] workgroup = WORKGROUP server string = %h server include = /etc/samba/dhcp.conf dns proxy = no log level = 2 syslog = 2 log file = /var/log/samba/log.%m max log size = 1000 syslog only = yes panic action = /usr/share/samba/panic-action %d encrypt passwords = true passdb backend = tdbsam obey pam restrictions = yes unix password sync = no passwd program = /usr/bin/passwd %u passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* . pam password change = yes socket options = TCP_NODELAY IPTOS_LOWDELAY guest account = nobody load printers = no disable spoolss = yes printing = bsd printcap name = /dev/null unix extensions = yes wide links = no create mask = 0777 directory mask = 0777 use sendfile = no null passwords = no local master = yes time server = yes wins support = yes ea support = yes store dos attributes = yes Note: I found this related question, but it explains the loss due to the user trying to transfer from NTFS to FAT32.

  Read the article

• Home Server: storage virtualisation, what to choose?

  - by Huygens

  I'm looking for virtualisation solutions for storage and OS for a home server. A sort of private cloud where I manage the storage space independently of the VM one. This question focus on storage management. (I have another question related to the VM/compute instance management). Here my environement and wishes. Server: HP Proliant MicroServer with 8 GB RAM (AMD Turion dual core with AMD-V technology) with 1 250GB system disk and up to 4 HDD (2 TB) for "data" OS types: only Linux (perhaps a *BSD VM in the future) Linux distributions do not matter, I'm familiar with RHEL, Fedora, Suse, Ubuntu, but any other recommandation will be fine The 4 HDD is going to be a software RAID array, probably RAID 5. storage should be "virtualised/cloudified": easy to extend: if I add a NAS on the network, I can include the NAS space capacity within this storage space as one virtual disk. This can be a NAS, an external HDD or another server. cluster FS or S3 style space or OpenStack block storage? Whatever is easier to manage/maintain and easy to integrate/plug to VM/compute instance. I would prefer free (libre, as in a free speach) and open source tools. But it does not have to be free as in a free beer. Note: the VMs I intend to run on top of this server are one dedicated to backup, one for a "owncloud/dropbox"-like service and perhaps one for media server (hosting video and photos). I'm not sure if traditional VMs or compute instance are the most suitable for this.

  Read the article

• Is there a way to do a sector level copy/clone from one hard drive to another?

  - by irrational John

  Without going into distracting details, I'm attempting to duplicate the contents of the 500GB drive in my MacBook to another 500GB drive. But this is turning out to be an unexpected hassle because the drive contains both the OS X partition and an NTFS partition with Win 7 via Apple's Boot Camp. With the exception of Clonezilla, the tools I have looked at so far all have some limitation. The Mac tools don't want to deal with the NTFS partition. The Windows tools are totally clueless about either the HFS+ partition and/or the hybrid MBR/GPT Boot Camp partitioning. Clonezilla looked like it would do what I want but apparently I can't figure out how to use it. After doing what I thought was a sector to sector copy I found that only the NTFS partition had been migrated. The others were apparently empty. (And frankly, I'm not positive Clonezilla migrated the partition table correctly either). Note: It takes over 2 hours using SATA to read/write all sectors with these drives. So I'm not up for using trial & error to narrow in on the right combination of Clonezilla options to use. I'm beginning to think that maybe the answer is to boot Linux (probably Ubuntu) and then use some ancient BSD command. Trouble is I don't know what command (or parameters to use) in order to do a sector level copy from one drive to another. As far as I know the drives have the same number of sectors so this should be trivial. Sigh.

  Read the article

• powershell vs GPO for installation, configuration, maintenance

  - by user52874

  My question is about using powershell scripts to install, configure, update and maintain Windows 7 Pro/Ent workstations in a 2008R2 domain, versus using GPO/ADMX/msi. Here's the situation: Because of a comedy of cumulative corporate bumpfuggery we suddenly found ourselves having to design, configure and deploy a full Windows Server 2008R2 and Windows 7 Pro/Enterprise on very short notice and delivery schedule. Of course, I'm not a windows expert by any means, and we're so understaffed that our buzzword bingo includes 'automate' and 'one-button' and 'it needs to Just Work'. (FWIW, I started with DEC, then on to solaris and cisco, then linux of various flavors with a smattering of BSD nowadays. I use Windows for email and to fill out forms). So we decided to bring in a contractor to do this for us. and they met the deadline. The system is up and mostly usable, and this is good. We would not have been able to do this. But it's the 'mostly' part that is proving to be the PIMA now, and I'm having to learn Microsoft stuff anyway until/if we can get a new contract with these guys for ongoing operations. Here's my question. The contractor used powershell almost exclusively for deployment, configuration and updating. My intensive reading over the last week leads me to think that the generally accepted practices for deployment, configuration and updating microsoft stuff uses elements of GPOs and ADMX templates, along with maybe some third party stuff like PolicyPak. Are there solid reasons that I've not found yet that powershell scripts would be preferred over the GPO methods? I'm going to discuss this with the contractor lead when he gets back from his vacation, and he'll be straight with me (nor do I think they set us up). But I can also see this might be a religious issue, so I would still like some background on this. Thoughts? or weblinks? Thanks!

  Read the article

• SQL SERVER – Server Side Paging in SQL Server 2011 Performance Comparison

  - by pinaldave

  Earlier, I have written about SQL SERVER – Server Side Paging in SQL Server 2011 – A Better Alternative. I got many emails asking for performance analysis of paging. Here is the quick analysis of it. The real challenge of paging is all the unnecessary IO reads from the database. Network traffic was one of the reasons why paging has become a very expensive operation. I have seen many legacy applications where a complete resultset is brought back to the application and paging has been done. As what you have read earlier, SQL Server 2011 offers a better alternative to an age-old solution. This article has been divided into two parts: Test 1: Performance Comparison of the Two Different Pages on SQL Server 2011 Method In this test, we will analyze the performance of the two different pages where one is at the beginning of the table and the other one is at its end. Test 2: Performance Comparison of the Two Different Pages Using CTE (Earlier Solution from SQL Server 2005/2008) and the New Method of SQL Server 2011 We will explore this in the next article. This article will tackle test 1 first. Test 1: Retrieving Page from two different locations of the table. Run the following T-SQL Script and compare the performance. SET STATISTICS IO ON; USE AdventureWorks2008R2 GO DECLARE @RowsPerPage INT = 10, @PageNumber INT = 5 SELECT * FROM Sales.SalesOrderDetail ORDER BY SalesOrderDetailID OFFSET @PageNumber*@RowsPerPage ROWS FETCH NEXT 10 ROWS ONLY GO USE AdventureWorks2008R2 GO DECLARE @RowsPerPage INT = 10, @PageNumber INT = 12100 SELECT * FROM Sales.SalesOrderDetail ORDER BY SalesOrderDetailID OFFSET @PageNumber*@RowsPerPage ROWS FETCH NEXT 10 ROWS ONLY GO You will notice that when we are reading the page from the beginning of the table, the database pages read are much lower than when the page is read from the end of the table. This is very interesting as when the the OFFSET changes, PAGE IO is increased or decreased. In the normal case of the search engine, people usually read it from the first few pages, which means that IO will be increased as we go further in the higher parts of navigation. I am really impressed because using the new method of SQL Server 2011,  PAGE IO will be much lower when the first few pages are searched in the navigation. Test 2: Retrieving Page from two different locations of the table and comparing to earlier versions. In this test, we will compare the queries of the Test 1 with the earlier solution via Common Table Expression (CTE) which we utilized in SQL Server 2005 and SQL Server 2008. Test 2 A : Page early in the table -- Test with pages early in table USE AdventureWorks2008R2 GO DECLARE @RowsPerPage INT = 10, @PageNumber INT = 5 ;WITH CTE_SalesOrderDetail AS ( SELECT *, ROW_NUMBER() OVER( ORDER BY SalesOrderDetailID) AS RowNumber FROM Sales.SalesOrderDetail PC) SELECT * FROM CTE_SalesOrderDetail WHERE RowNumber >= @PageNumber*@RowsPerPage+1 AND RowNumber <= (@PageNumber+1)*@RowsPerPage ORDER BY SalesOrderDetailID GO SET STATISTICS IO ON; USE AdventureWorks2008R2 GO DECLARE @RowsPerPage INT = 10, @PageNumber INT = 5 SELECT * FROM Sales.SalesOrderDetail ORDER BY SalesOrderDetailID OFFSET @PageNumber*@RowsPerPage ROWS FETCH NEXT 10 ROWS ONLY GO Test 2 B : Page later in the table -- Test with pages later in table USE AdventureWorks2008R2 GO DECLARE @RowsPerPage INT = 10, @PageNumber INT = 12100 ;WITH CTE_SalesOrderDetail AS ( SELECT *, ROW_NUMBER() OVER( ORDER BY SalesOrderDetailID) AS RowNumber FROM Sales.SalesOrderDetail PC) SELECT * FROM CTE_SalesOrderDetail WHERE RowNumber >= @PageNumber*@RowsPerPage+1 AND RowNumber <= (@PageNumber+1)*@RowsPerPage ORDER BY SalesOrderDetailID GO SET STATISTICS IO ON; USE AdventureWorks2008R2 GO DECLARE @RowsPerPage INT = 10, @PageNumber INT = 12100 SELECT * FROM Sales.SalesOrderDetail ORDER BY SalesOrderDetailID OFFSET @PageNumber*@RowsPerPage ROWS FETCH NEXT 10 ROWS ONLY GO From the resultset, it is very clear that in the earlier case, the pages read in the solution are always much higher than the new technique introduced in SQL Server 2011 even if we don’t retrieve all the data to the screen. If you carefully look at both the comparisons, the PAGE IO is much lesser in the case of the new technique introduced in SQL Server 2011 when we read the page from the beginning of the table and when we read it from the end. I consider this as a big improvement as paging is one of the most used features for the most part of the application. The solution introduced in SQL Server 2011 is very elegant because it also improves the performance of the query and, at large, the database. Reference : Pinal Dave (http://blog.SQLAuthority.com) Filed under: SQL, SQL Authority, SQL Optimization, SQL Performance, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology

  Read the article

• Month in Geek: December 2010 Edition

  - by Asian Angel

  As 2010 draws to a close, we have gathered together another great batch of article goodness for your reading enjoyment. Here are our ten hottest articles for December. Note: Articles are listed as #10 through #1. The 50 Best How-To Geek Windows Articles of 2010 Even though we cover plenty of other topics, Windows has always been a primary focus around here, and we’ve got one of the largest collections of Windows-related how-to articles anywhere. Here’s the fifty best Windows articles that we wrote in 2010. Read the article Desktop Fun: Happy New Year Wallpaper Collection [Bonus Edition] As this year draws to a close, it is a time to reflect back on what we have done this year and to look forward to the new one. To help commemorate the event we have put together a bonus size edition of Happy New Year wallpapers for your desktops. Read the article LCD? LED? Plasma? The How-To Geek Guide to HDTV Technology With image technology progressing faster than ever, High-Def has become the standard, giving TV buyers more options at cheaper prices. But what’s different in all these confusing TVs, and what should you know before buying one? Read the article HTG Explains: Which Linux File System Should You Choose? File systems are one of the layers beneath your operating system that you don’t think about—unless you’re faced with the plethora of options in Linux. Here’s how to make an educated decision on which file system to use. Read the article Desktop Fun: Merry Christmas Fonts Christmas will soon be here and there are lots of cards, invitations, gift tags, photos, and more to prepare beforehand. To help you get ready we have gathered together a great collection of fun holiday fonts to help turn those ordinary looking holiday items into extraordinary looking ones. Read the article Microsoft Security Essentials 2.0 Kills Viruses Dead. Download It Now. Microsoft’s Security Essentials has been our favorite anti-malware application for a while—it’s free, unobtrusive, and it doesn’t slow your PC down, but now it’s even better with the new 2.0 release, which adds network filtering, heuristic protection, and more. Read the article 20 OS X Keyboard Shortcuts You Might Not Know Mastering the keyboard will not only increase your navigation speed but it can also help with wrist fatigue. Here are some lesser known OS X shortcuts to help you become a keyboard ninja. Read the article 20 Windows Keyboard Shortcuts You Might Not Know Mastering the keyboard will not only increase your navigation speed but it can also help with wrist fatigue. Here are some lesser known Windows shortcuts to help you become a keyboard ninja. Read the article The 50 Best Registry Hacks that Make Windows Better We’re big fans of hacking the Windows Registry around here, and we’ve got one of the biggest collections of registry hacks you’ll find. Don’t believe us? Here’s a list of the top 50 registry hacks that we’ve covered. Read the article The Complete List of iPad Tips, Tricks, and Tutorials The Apple iPad is an amazing tablet, and to help you get the most out of it, we’ve put together a comprehensive list of every tip, trick, and tutorial for you. Read on for more. Read the article Latest Features How-To Geek ETC The 20 Best How-To Geek Linux Articles of 2010 The 50 Best How-To Geek Windows Articles of 2010 The 20 Best How-To Geek Explainer Topics for 2010 How to Disable Caps Lock Key in Windows 7 or Vista How to Use the Avira Rescue CD to Clean Your Infected PC The Complete List of iPad Tips, Tricks, and Tutorials Tune Pop Enhances Android Music Notifications Another Busy Night in Gotham City Wallpaper Classic Super Mario Brothers Theme for Chrome and Iron Experimental Firefox Builds Put Tabs on the Title Bar (Available for Download) Android Trojan Found in the Wild Chaos, Panic, and Disorder Wallpaper

  Read the article

• Change a File Type’s Icon in Windows 7

  - by Trevor Bekolay

  In Windows XP, you could change the icon associated with a file type in Windows Explorer. In Windows 7, you have to do some registry hacking to change a file type’s icon. We’ll show you a much easier and faster method for Windows 7. File Types Manager File Types Manager is a great little utility from NirSoft that includes the functionality of Windows XP’s folder options and adds a whole lot more. It works great in Windows 7, and its interface makes it easy to change a bunch of related file types at once. A common problem we run into are icons that look too similar. You have to look for a few seconds to see the difference between the movies and the text files. Let’s change the icon for the movie files to make visually scanning through directories much easier. Open up File Types Manager. Find the “Default Icon” column and click on it to sort the list by the Default Icon. (We’ve hidden a bunch of columns we don’t need, so you may find it to be farther to the right.) This groups together all file extensions that already have the same icon. This is convenient because we want to change the icon of all video files, which at the moment all have the same default icon. Click the “Find” button on the toolbar, of press Ctrl+F. Type in a file type that you want to change. Note that all of the extensions with the same default icon are grouped together. Right click on the first extension whose icon you want to change and click on Edit Selected File Type, or select the first extension and press F2. Click the “…” button next to the Default Icon text field. Click on the Browse… button. File Types Manager allows you to select .exe, .dll, or .ico files. In our case, we have a .ico file that we took from the wonderful public domain Tango icon library. Select the appropriate icon (if you’re using a .exe or .dll there could be many possible icons) then click OK. Repeat this process for each extension whose icon you would like to change. Now it’s much easier to see at a glance which files are movies and which are text files! Of course, this process will work for any file type, so customize your files’ icons as you see fit. Download File Types Manager from NirSoft for Windows Similar Articles Productive Geek Tips Change the Default Editor for Batch Files in VistaCustomizing Your Icons in Windows XPChange Your Windows 7 Library Icons the Easy WayRestore Missing Desktop Icons in Windows 7 or VistaCustomize Your Folder Icons in Windows XP TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Scan your PC for nasties with Panda ActiveScan CleanMem – Memory Cleaner AceStock – The Personal Stock Monitor Add Multiple Tabs to Office Programs The Wearing of the Green – St. Patrick’s Day Theme (Firefox) Perform a Background Check on Yourself

  Read the article

• My new laptop - with a really nice battery option

  - by Rob Farley

  It was about time I got a new laptop, and so I made a phone-call to Dell to discuss my options. I decided not to get an SSD from them, because I’d rather choose one myself – the sales guy tells me that changing the HD doesn’t void my warranty, so that’s good (incidentally, I’d love to hear people’s recommendations for which SSD to get for my laptop). Unfortunately this machine only has one HD slot, but I figure that I’ll put lots of stuff onto external disks anyway. The machine I got was a Dell Studio XPS 16. It’s red (which suits my company), but also has the Intel® Core™ i7-820QM Processor, which is 4 Cores/8 Threads. Makes for a pretty Task Manager, but nothing like the one I saw at SQLBits last year (at 96 cores), or the one that my good friend James Rowland-Jones writes about here. But the reason for this post is actually something in the software that comes with the machine – you know, the stuff that most people uninstall at the earliest opportunity. I had just reinstalled the operating system, and was going through the utilities to get the drivers up-to-date, when I noticed that one of Dell applications included an option to disable battery charging. So I installed it. And sure enough, I can tell the battery not to charge now. Clearly Dell see it as a temporary option, and one that’s designed for when you’re on a plane. But for me, I most often use my laptop with the power plugged in, which means I don’t need to have my battery continually topping itself up. So I really love this option, but I feel like it could go a little further. I’d like “Not Charging” to be the default option, and let me set it when I want to charge it (which should theoretically make my battery last longer). I also intend to work out how this option works, so that I can script it and put it into my StartUp options (so it can be the Default setting). Actually – if someone has already worked this out and can tell me what it does, then please feel free to let me know. Even better would be an external switch. I had a switch on my old laptop (a Dell Latitude) for WiFi, so that I could turn that off before I turned on the computer (this laptop doesn’t give me that option – no physical switch for flight mode). I guess it just means I’ll get used to leaving the WiFi off by default, and turning it on when I want it – might save myself some battery power that way too. Soon I’ll need to take the plunge and sync my iPhone with the new laptop. I’m a little worried that I might lose something – Apple’s messages about how my stuff will be wiped and replaced with what’s on the PC doesn’t fill me with confidence, as it’s a new PC that doesn’t have stuff on it. But having a new machine is definitely a nice experience, and one that I can recommend. I’m sure when I get around to buying an SSD I’ll feel like it’s shiny and new all over again! Share this post: email it! | bookmark it! | digg it! | reddit! | kick it! | live it!

  Read the article

• Text inside <p> shrinks on mobile devices while div does not [migrated]

  - by guisasso

  I asked this question on stack overflow, but didn't get any answers, so I'm trying here. Does anybody know whats happening here? I tested on opera, dolphin and the factory android browser. (although it seems now to be working on opera) The div doesn't change size, but the text somehow is shrunk to fit on part of a div. Anyway to prevent this? Just to be clear, I'm trying to achieve on the mobile browser the same look as the pc version. As the problem seems to be with the browsers, how can I force the text to take the full width of the div? I tried setting the p tag to 100% with no success. The div has to have that width and be aligned to the left of the page. On a Pc, as it should be: I shrunk the code as much as I could: <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd"> <html xmlns="http://www.w3.org/1999/xhtml" lang="en-us"> <head> <meta content="text/html; charset=utf-8" http-equiv="Content-Type" /> <meta content="" name="keywords" /> <meta content="" name="description" /> <title></title> </head> <body> <div style="width:1000px; margin-left:auto; margin-right:auto;" > <div style="float:left; width:758px; background-color:aqua;"> <p> Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text .<br /> <br /> Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text Random text .<br /> <br /> Random text Random text Random text Random text <a href="http://www.a.com/a.html"> Random text </a> Random text Random text . </p> </div> </div> </body> </html> Thanks.

  Read the article

• From the Tips Box: Pre-installation Prep Work Makes Service Pack Upgrades Smoother

  - by Jason Fitzpatrick

  Last month Microsoft rolled out Windows 7 Service Pack 1 and, like many SP releases, quite a few people are hanging back to see what happens. If you want to update but still error on the side of caution, reader Ron Troy  offers a step-by-step guide. Ron’s cautious approach does an excellent job minimizing the number of issues that could crop up in a Service Pack upgrade by doing a thorough job updating your driver sets and clearing out old junk before you roll out the update. Read on to see how he does it: Just wanted to pass on a suggestion for people worried about installing Service Packs.  I came up with a ‘method’ a couple years back that seems to work well. Run Windows / Microsoft Update to get all updates EXCEPT the Service Pack. Use Secunia PSI to find any other updates you need. Use CCleaner or the Windows disk cleanup tools to get rid of all the old garbage out there.  Make sure that you include old system updates. Obviously, back up anything you really care about.  An image backup can be real nice to have if things go wrong. Download the correct SP version from Microsoft.com; do not use Windows / Microsoft Update to get it.  Make sure you have the 64 bit version if that’s what you have installed on your PC. Make sure that EVERYTHING that affects the OS is up to date.  That includes all sorts of drivers, starting with video and audio.  And if you have an Intel chipset, use the Intel Driver Utility to update those drivers.  It’s very quick and easy.  For the video and audio drivers, some can be updated by Intel, some by utilities on the vendor web sites, and some you just have to figure out yourself.  But don’t be lazy here; old drivers and Windows Service Packs are a poor mix. If you have 3rd party software, check to see if they have any updates for you.  They might not say that they are for the Service Pack but you cut your risk of things not working if you do this. Shut off the Antivirus software (especially if 3rd party). Reboot, hitting F8 to get the SafeMode menu.  Choose SafeMode with Networking. Log into the Administrator account to ensure that you have the right to install the SP. Run the SP.  It won’t be very fancy this way.  Maybe 45 minutes later it will reboot and then finish configuring itself, finally letting you log in. Total installation time on most of my PC’s was about 1 hour but that followed hours of preparation on each. On a separate note, I recently got on the Nvidia web site and their utility told me I had a new driver available for my GeForce 8600M GS.  This laptop had come with Vista, now has Win 7 SP1.  I had a big surprise from this driver update; the Windows Experience Score on the graphics side went way up.  Kudo’s to Nvidia for doing a driver update that actually helps day to day usage.  And unlike ATI’s updates (which I need for my AGP based system), this update was fairly quick and very easy.  Also, Nvidia drivers have never, as I can recall, given me BSOD’s, many of which I’ve gotten from ATI (TDR errors).How to Enable Google Chrome’s Secret Gold IconHTG Explains: What’s the Difference Between the Windows 7 HomeGroups and XP-style Networking?Internet Explorer 9 Released: Here’s What You Need To Know

  Read the article

• Download YouTube Videos the Easy Way

  - by Trevor Bekolay

  You can’t be online all the time, and despite the majority of YouTube videos being nut-shots and Lady Gaga parodies, there is a lot of great content that you might want to download and watch offline. There are some programs and browser extensions to do this, but we’ve found that the easiest and quickest method is a bookmarklet that was originally posted on the Google Operating System blog (it’s since been removed). It will let you download standard quality and high-definition movies as MP4 files. Also, because it’s a bookmarklet, it will work on any modern web browser, and on any operating system! Installing the bookmarket is easy – just drag and drop the Get YouTube video link below to the bookmarks bar of your browser of choice. If you’ve hidden the bookmark bar, in most browsers you can right-click on the link and save it to your bookmarks. Get YouTube video   With the bookmarklet available in your browser, go to the YouTube video that you’d like to download. Click on the Get YouTube video link in your bookmarks bar, or in the bookmarks menu, wherever you saved it earlier. You will notice some new links appear below the description of the video. If you download the standard definition file, it will save as “video.mp4” by default. However, if you download the high definition file, it will save with the same name as the title of the video. There are many methods of downloading YouTube videos…but we think this is the easiest and quickest method. You don’t have to install anything or use up resources, but you can still get a link to download an MP4 with one click. Do you use a different method to download Youtube videos? Let us know about it in the comments! javascript:(function(){if(document.getElementById(’download-youtube-video’))return;var args=null,video_title=null,video_id=null,video_hash=null;var download_code=new Array();var fmt_labels={‘18′:’standard%20MP4′,’22′:’HD%20720p’,'37′:’HD%201080p’};try{args=yt.getConfig(’SWF_ARGS’);video_title=yt.getConfig(’VIDEO_TITLE’)}catch(e){}if(args){var fmt_url_map=unescape(args['fmt_url_map']);if(fmt_url_map==”)return;video_id=args['video_id'];video_hash=args['t'];video_title=video_title.replace(/[%22\'\?\\\/\:\*%3C%3E]/g,”);var fmt=new Array();var formats=fmt_url_map.split(’,');var format;for(var i=0;i%3Cformats.length;i++){var format_elems=formats[i].split(’|');fmt[format_elems[0]]=unescape(format_elems[1])}for(format in fmt_labels){if(fmt[format]!=null){download_code.push(’%3Ca%20href=\”+(fmt[format]+’&title=’+video_title)+’\'%3E’+fmt_labels[format]+’%3C/a%3E’)}elseif(format==’18′){download_code.push(’%3Ca%20href=\’http://www.youtube.com/get_video?fmt=18&video_id=’+video_id+’&t=’+video_hash+’\'%3E’+fmt_labels[format]+’%3C/a%3E’)}}}if(video_id==null||video_hash==null)return;var div_embed=document.getElementById(’watch-embed-div’);if(div_embed){var div_download=document.createElement(’div’);div_download.innerHTML=’%3Cbr%20/%3E%3Cspan%20id=\’download-youtube-video\’%3EDownload:%20′+download_code.join(’%20|%20′)+’%3C/span%3E’;div_embed.appendChild(div_download)}})() Similar Articles Productive Geek Tips Watch YouTube Videos in Cinema Style in FirefoxDownload YouTube Videos with Cheetah YouTube DownloaderStop YouTube Videos from Automatically Playing in FirefoxImprove YouTube Video Viewing in Google ChromeConvert YouTube Videos to MP3 with YouTube Downloader TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional 15 Great Illustrations by Chow Hon Lam Easily Sync Files & Folders with Friends & Family Amazon Free Kindle for PC Download Stretch popurls.com with a Stylish Script (Firefox) OldTvShows.org – Find episodes of Hitchcock, Soaps, Game Shows and more Download Microsoft Office Help tab

  Read the article

• Watch Netflix Instant Movies in Boxee

  - by DigitalGeekery

  Boxee is multi-platform Media PC application with a host of media applications. One of which is the popular Movie service, Netflix. Today we’ll show you how to get setup to watch Netflix Instant streaming video in Boxee. Note: Nexflix requires Microsoft Silverlight which unfortunately means Boxee users running Linux out of luck. What You’ll Need A Netflix account Authorize your Netflix account with Boxee Install Microsoft Silverlight Authorize Your Netflix Account First, we need to authorize our Netflix account with Boxee. (See link below). Type in your Boxee username and password and click “Login.”  When prompted, click “Authorize.”   Click “Yes, Link This Account.”    Install Silverlight If you don’t already have Silverlight installed, you’ll need to do so. See the download link at the end of the article.   Log into Boxee Now we’re ready to log into Boxee. Once logged in, click on “Apps” on the Home screen.   From the My Apps screen click on Netflix. Then click “Start.” Click “Yes” to enable the cookie.   Now you’ll enter the Netflix App. From here, you can browse your Instant Queue, Recommendations, New Arrivals, Browse Genre, or Search for available titles.   Click on a selection you’d like to watch. From here, you can Play, Rate, or even add the title to your regular Netflix Queue.   With a remote or the on-screen controls you can pause, stop, play, and skip forward or back through the video.   Now you’re all set to enjoy the Netflix Instant library with Boxee. Netflix Instant is one of many great Apps included with Boxee. While the current available selection isn’t exactly overwhelming, most subscribers will likely find enough to keep themselves entertained in between DVD deliveries. Haven’t tried Boxee yet? Check out our article on getting started with Boxee. Links Authorize your Netflix account with Boxee Install Microsoft Silverlight Similar Articles Productive Geek Tips Using Netflix Watchnow in Windows Vista Media Center (Gmedia)Find Movies and TV Based on your Mood with JinniGetting Started with BoxeeQuickly Find Movies to Watch at Hello MoviesIntegrate Boxee with Media Center in Windows 7 TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Change DNS servers on the fly with DNS Jumper Live PDF Searches PDF Files and Ebooks Converting Mp4 to Mp3 Easily Use Quick Translator to Translate Text in 50 Languages (Firefox) Get Better Windows Search With UltraSearch Scan News With NY Times Article Skimmer

  Read the article

• View Mobile Websites in Windows with Safari 4 Developer Tools

  - by Matthew Guay

  Want to try out mobile websites designed for the iPhone and other mobile devices on your PC?  Safari 4 for Windows lets you do this easily with their developer tools. By default, Safari will show standard desktop websites.  But by making a simple change, you can switch it to work like Safari Mobile on the iPhone or iPod Touch. Getting Started First make sure you have Safari 4 for Windows installed.  You can download Safari directly (link below) and install it as usual.   Or if you already have another Apple program installed, such as QuickTime or iTunes, then you can install it from Apple Software update.  Simply enter apple software update in the Start menu search box. And then select Safari 4 from the list of new software available.  Click Install to automatically download and install Safari. Accept the license Agreement, and then Safari will automatically install. Once this is finished, Safari will be ready to use. View Mobile Sites in Safari First, we need to enable the developer tools.  Click the gear icon on the toolbar, and select Preferences. Click the Advanced tab, and then check the box that says “Show Develop menu in menu bar”. Once you’ve closed your settings box, click the page icon, select Develop, then User Agent, and then choose one of the Mobile Safari settings.  In our test we chose Mobile Safari 3.1.2 – iPhone. To make your browser emulate a mobile device better, you can hide the bookmarks and tab bar to have a more streamlined interface. Click the Gear icon, and select “Hide Bookmarks Bar”, and then repeat and click “Hide Tab Bar”. You can also shrink your window to be closer to the size of a mobile device screen.  Once you’ve done these things, Safari should look similar to this screenshot.  Here we have loaded Google.com, and you can see it in its iPhone-style interface. Simply enter any website into the address bar, and it will load in its mobile interface if it has one.  Here is Google’s other mobile offerings, right inside Windows. Gmail loads messages with the default iPhone interface. One especially interesting mobile site is Apple’s online iPhone User Guide.  When loaded in Safari with the iPhone setting, it loads with a very nice mobile UI that works just like an iPhone app.  In fact, you can even click and drag to scroll, just like you would with your finger on an iPhone. Conclusion Even if you do not have a Smartphone, you can still preview what websites will look like on them with this trick. Not all sites will work of course, but it’s fun to play around with different sites that have mobile versions. Links: Safari 4 Download Apple iPhone online user guide Similar Articles Productive Geek Tips Make Safari Stop Crashing Every 20 Seconds on Windows VistaCustomize Safari for Windows ToolbarSave Screen Space by Hiding the Bookmarks Toolbar in Safari for WindowsEdit Text in a Webpage with Internet Explorer 8Keep Websites From Using Tiny Fonts in Safari TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Windows Media Player 12: Tweak Video & Sound with Playback Enhancements Own a cell phone, or does a cell phone own you? Make your Joomla & Drupal Sites Mobile with OSMOBI Integrate Twitter and Delicious and Make Life Easier Design Your Web Pages Using the Golden Ratio Worldwide Growth of the Internet

  Read the article

< Previous Page | 145 146 147 148 149 150 151 152 153 154 155 156  | Next Page >