Search Results

Search found 518 results on 21 pages for 'hooked'.

Page 15/21 | < Previous Page | 11 12 13 14 15 16 17 18 19 20 21  | Next Page >

• Distorted Sound

  - by BCable

  I have my laptop hooked up to my receiver for sound output. I hear a hissing/crackling background sound that is really loud and hard to just ignore (but possible). When my 360 is connected, the sound comes out perfect, so it's just with this laptop. Previously, I thought it was just my laptop and just submissively just let it slide. I just bought a brand new laptop though and it's doing the same thing. I have found out more information now that I know it's not my laptop. I have used this laptop in similar environments where it worked just fine (different speakers). I have bought a new cable to connect to my receiver and it did nothing (headphone jack to RCA). I tried different ports on the receiver (Video 1-3) and it always happens. I have discovered that the sound goes away if I unplug my laptop (so it's running on battery). Because of the last one, I tried plugging my laptop into a different outlet across the room and it's STILL doing it. Doesn't matter if I boot to Linux or Windows, yet my phone (Android G1) doesn't cause this sound using the exact same cable. Any ideas? I'm out of them! Thanks!

  Read the article

• Cisco QoS Guidance

  - by Kyle Brandt

  I have a 10M connection to the internet that is hooked into a 100M port. I am getting started with QoS, and am hopping for a little guidance on setting it up on a Cisco 3825 router. Right now I am going forward with the idea that I have to implement it on my router, and the provider can't provide QoS for me. How I envision it working is that the QoS will drop or queue packets on my router and that will help prevent a situation where the provider has to start dropping a lot of packets. Right now all I am tasked with is making sure that one of the 3 LANs gets a certain slice (say 3M for Gig Lan1) of the 10M internet connection (But ideally this will be more flexible in the Future). 10M Internet on 100M port on HWIC-4ESW +-----------------------+ | | Gig Lan1 | Cisco 3825 | Lan3 on HWIC-4ESW | | +-----------------------+ Gig Lan2 I need to learn more about QoS, but having a target technology and maybe example configuration will help me wrap my head around the reading I am doing a little more. Which Cisco QoS Technology do you recommend for this particular situation? Have a basic sample config of how this might work? Right now the 10M line is not congested, so this more to have something in place in case it starts to become mildly congested in the future. I do have VOIP at one location connected to this one over the Internet that goes through a VPN tunnel. Everything else that is between this location and other offices is on a separate MPLS network.

  Read the article

• Misconfigured external monitor on Mac OS X Snow Leopard 10.6.3

  - by Mike

  I have an external monitor (specifically, an HDTV) hooked up to my 2.53GHz 13" macbook pro. This display works fine and I use it with my mac in clamshell mode (eg. with an external keyboard/mouse and the laptop closed and the built-in mac screen turned off) My Mac has multiple users on it. For User A I can use the mac with the external monitor in both clamshell and dual-monitor setups. For User B, I can use the monitor in a dual-monitor setup, but whenever I switch to clamshell mode the Mac switches to an incorrect output resolution or frequency setting that my HDTV doesn't recognize, resulting in a blank screen and a message about Unsupported Resolution. Chances are I did this to myself by misconfiguring my display settings at some point in the past, but I have no idea how to undo it. I (obviously) can't seen the display to change the settings when it's borked. I can see the display settings if I switch to Dual-monitor mode, but those settings only affect the dual monitor setup; no matter how I change the settings in dual-monitor mode, the clamshell mode setup remains borked. How can I dig myself out of this hole?

  Read the article

• Devices on one switch can't see devices on another switch

  - by jockey69

  I have RoadRunner Internet cable service hooked to a Motorola Surfboard modem. This is connected to a 10/100 wireless router (located in the garage). Downstairs, I have a ZyXEL GS-108b gigabit switch connected to one port on the router. From this switch I ran connections to a PS3, DVR, Vonage box and a wireless router (Buffalo AirStation 10/100). The Buffalo AirStation works as a wireless AP for other laptops, iPads and cell phones. Upstairs, I have an Asus gigabit switch connected to a gaming desktop, printer, and a media server on FreeNAS (PS3 Media Server on FreeNAS). The router is configured to assign static IPs to both the PS3 and the media server. Problem - I connect a laptop to the switch downstairs after disabling the wireless, thus making sure that I am accessing internet through the wired connection (and the router in the garage). All my computers, iPads and cell phones are able to connect to the internet without a problem. My PS3 connects to the interent with a wired connection but is unable to access the media server (I get a message that no media server is found). I used a wired laptop downstairs (connected to switch downstairs) but am unable to ping either the PS3 or media server! I may be doing something silly but am at my wits' end. Please help!

  Read the article

• How do I make ESXi 5.0 to shutdown virtual machines when the physical power button is pushed?

  - by Pawel Sawicki

  I have a home NAS/DLNA server built out of an HP Micro Server with the HP branded VMware ESXi 5.0.0 build-623860 (free license) installed. Being a home media center I'd like it to be "manageable" by all my household members. This requires that it needs to be powered on an off (including all the VMs inside) by anybody with the physical access to the server by simply pressing the power button on the chassis. The "startup" part is easy to obtain - all I had to do was to configure the startup/shutdown policy: Once the server powers up, all VMs start as well and that's exactly what I need. Well.. it did work up until 5.0.0U1, but that's a different story: http://blogs.vmware.com/vsphere/2012/03/free-esxi-hypervisor-auto-start-breaks-with-50-update-1.html Unfortunately, pressing the power button doesn't gracefully shutdown the guest machines - they are terminated instead. If I run the "shut down" command from the vSphere Client interface guests are powered off. I'd like to get the same end result when the physical power button is switched. I've poked around a bit on the ESXi server. There's a "/sbin/shutdown.sh" script that seemed to do exactly what I need... but after trying it does exactly what the power off button. The "/etc/inittab" contains an entry for the "shutdown" level but I suppose it's not hooked to the power button. I can't find any acpi related configuration, neither do I know what exactly is executed when the power button is pressed. Does anybody have a clue how can I make the VMs shutdown automatically when the physical power switch is pressed to turn of the computer?

  Read the article

• Trouble with HP printer

  - by reyjavikvi

  I have a HP Photosmart C3180 (it's a printer/scanner). For some reason, it recently stopped working. The power light is blinking (I think all the other lights are one, but don't remember, I'm not there right now), and the only way to turn it off is to unplug it. It won't print anything, and when you put a page in the tray it sucks it in without printing anything on it and stops when the paper is on its way out (Again, I don't remember how we managed to get it out, sorry). This printer is hooked up to a computer running XP, but it doesn't work either when printing from the network. Weirdly, the scanner works fine. Do you have any ideas on what could be the problem? Could it be a driver problem? By the way, sorry if the question lacks a bit of detail. I don't know much about printers, and I don't have it here so I can't remember exactly all the details. If needed I can update the question tonight or tomorrow.

  Read the article

• Windows XP over two monitors, but one of them switches off at boot... how to fix? How to switch bac

  - by jae

  When booting into XP (x64, Athlon II X2 245, 4GB RAM), my main monitor (got two 19" TFTs hooked up, two gfx cards, a 4650 (1GB, the primary monitor's on this) and a 4350 (512MB)) switches off. Logging in blind (cursor down key, typing password) gets me one screen, the secondary. Booted correctly until about two days ago. No clue what's the cause, last change was (if I don't overlook something) installing the ATI 9-12 hotfix. And booting into Windows 7, after returning from 7, it was like this. For some weird reason, I cannot start Catalyst Control Center (I right-click desktop, choose the CCC entry, the pointer changes to hourglass for a half-second... and nothing. Likewise with "Properties"... I think, as all windows open on the primary (off) screen, and no entry appears in the task bar for Properties) Completely stumped. Windows 7, same setup, works w/o a hitch. The primary monitor appears to run in some unknown, but pretty low, resolution, as the mouse pointer only moves onto it at about half-height. But, w/o CCC or display properties, I cannot check. And, obviously, not change anything. Hope this was not too long-winded. And I'm sure I still forgot essential stuff. :P

  Read the article

• How do I hook into Tar with BASH?

  - by orb

  Long Story Short I am working with Tar archives that contain PNG images in base64 encoding. I would like to use BASH (or whatever else works) to hook into the extraction function of Tar to decode PNG images from base64 encoding to standard PNG encoding after the files are unpacked. A simple cat $input-file | base64 -d >$output-file will successfully decode the images. Is there a way I can hook into tar -xf so that users do not have to do any (or minimal) extra work to decode the images? In the GNU Tar documentation (http://www.gnu.org/software/tar/manual/html_chapter/Backups.html#SEC97) I found that there are in fact variables reserved to hold the names of functions I desire to be hooked into various moments in Tar program execution. However, the documentation explains that these variables, along with other variables that can be set to configure Tar, are located in a file named backup-specs. Unfortunately, the path to this file is not given. Further, running sudo find / -name backup-specs tells me that this file is not present on my Ubuntu version 13.04 system. Background Information not included in the Long Story Short I have been working on a browser-based (WebGL) particle effect creation application (http://www.particleeffect.org), (https://github.com/cgrabowski/webgl-particle-effect-editor), (https://github.com/cgrabowski/webgl-particle-effect). I have began to write a client-side-only solution for saving and loading effect data as a tar archive. However, since client-side JavaScript has limited capability to process binary data, the images used as textures in the effect are saved with base64 encoding. I have been able to implement saving effect data as a Tar archive (haven't pushed that to Github yet). However, the images present in said Tar archive cannot be manipulated unless they are decoded from base64 encoding.

  Read the article

• Cheap desktop computer in 19" rack-mountable form-factor?

  - by Alex Basson

  I'm a high school teacher at a small private school. As of this year, we have SMARTBoards in every classroom (though I've had one in the class I share for two years now). The classrooms themselves don't have computers in them, so we teachers bring our laptops to class and connect them to the boards. This has several disadvantages: This takes a few minutes while we wait for the board to boot up and then orient the board to our individual laptop -- we have to do this every time b/c different teachers have different laptops requiring different orientations. This isn't ideal because when you only have 43 minutes per class period, waiting five minutes just to get started is a real waste. Carrying your laptop to class doesn't sound so bad until you consider that we're also carrying textbooks and piles of student papers, and we're carrying it all through crowded high school hallways. More than one laptop has fallen THUNK to the floor, with dire consequences. We feel we could eliminate the need to use our laptops with the SMARTBoards if we had a dedicated computer in each classroom hooked up to the board at all times. Each board set-up is connected to a podium with a standard 19" rack in it, currently housing a power supply and DVD player. There're plenty of rack spaces available. So I'm thinking: maybe we could get some inexpensive computers in a 19" rack-mountable form factor, install them in the podiums, and connect them to the boards on a permanent basis. Any suggestions?

  Read the article

• MAMP Pro .xip.io, fixing urls with htaccess

  - by user3540018

  I've got all my websites set up with MAMP Pro. For instance, I got it set up, so when I go to example.com, the browser displays the website that's set up on my iMac. Now, I wanna get MAMP Pro to work so I can view my website on my other computers/devices (which are all hooked up on the same network.) So far all I had to do is check the checkbox "via Xip.io (LAN only)", and now I can view my website on my other computers/devices within my LAN by simply going to example.com.10.0.1.13.xip.io. Problem is, whenever I'm on this other computer/device, when I click on the links, I get 404 error. ie. whenever I go to example.com/news, I get the 404. But when I go to example.com.10.0.1.13.xip.io/news, THEN I get the right page. So in order to solve my problem I need to rewrite the urls. So whenever someone clicks on a link ie. goes straight to example.com/news, he'll go to example.com.10.0.1.13.xip.io/news. I don't want to change all the links in my MySQL file, but I believe I can do it simply with the htaccess file. I've opened the htaccess file and added the last two lines, but it just doesn't work. <IfModule mod_rewrite.c> RewriteEngine On # Send would-be 404 requests to Craft RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteCond %{REQUEST_URI} !^/(favicon\.ico|apple-touch-icon.*\.png)$ [NC] RewriteRule (.+) index.php?p=$1 [QSA,L] RewriteCond %{HTTP_HOST} ^example\.com RewriteRule ^(.*)$ http://www.example.com.10.0.1.13.xip.io/$1 [R=permanent,L] </IfModule> Or perhaps I don't need to change the htaccess file, is there something that I could be missing in the MAMP Pro settings, or perhaps a MAMP extension that I need?

  Read the article

• How do I stop panning on a monitor that supports a specific resolution?

  - by IronicMuffin

  Hi all, I've been battling this for a few days now. Any and all help is appreciated. I have a planar monitor with a native res of 1280x1024. At one point, I had used PowerStrip to override "something" and set the res to 1600x1200, and it worked great. I then installed new intel graphics drivers for my 86895g (or w/e model) video card, which screwed up whatever settings I had. If I set it to 1600x1200 this time, it would set the res correctly, but give me a 1280x1024 viewport and the screen would pan when the mouse got to the edges of the screen. Absolutely not useful. Ok, so I was limited to 1280x1024 now. W/e. Now...enter new video card with two video ports. I have two monitors now and the latest nVidia drivers. I decide to try to get dual 1600x1200 going...ended up screwing the original monitor up so much now that it's at 1280x1024, with a 1024x768 viewport and panning! Absolutely not usable now. So what I need, and I can't seem to find on any forums, is help doing one or more of the following: Clearing out all monitor/edid info out of the windows registry without corrupting the registry. Actually correctly override the EDID values and get my sweet res back. Some other way of getting back to at least dual 1280x1024 with NO panning. Note: My device manager shows 4 monitors for some reason. My registry shows entries for all sorts of monitors that have been hooked up to the machine over the years. It's making it difficult to debug. Experience with PowerStrip would be helpful. I've been mucking with Phoenix EDID designer and MonInfo as well, but I'm stumbling around in the dark with these. Windows XP SP2 nVidia GeForce 6200 nVidia drivers: v258.96 Monitor: Planar PL 1910M Thanks!

  Read the article

• Windows 7 Not Recognizing Camera Nor iPhone as Camera

  - by taudep

  I've been struggling with this one for a few days. I've recently upgraded an older computer to Windows 7 Home Premium. Neither my digital camera (A Canon SD1200IS) nor iPhone are ever detected as cameras, nor ever show up as accessable in Explorer. With the Canon camera, no driver is required. It's supposed to work with the default Windows 7 drivers. However, in the Control Panel's Device Manager, I'm always seeing a yellow icon next to the "Canon Digital Camera" device. I've uninstalled the device and let Windows attempt to reinstall, but it can never find a driver to install. With the iPhone, it's very similar. One big difference, though, is that iTunes can see the iPhone and back it up, etc. However, again when I go to the Device Manager, there's a yellow icon next to the iPhone. I've uninstalled iTunes, reinstalled, rebooted, deleted drivers, and let Window try to reinstall the driver, but it can never find the driver. So there seems to be some correlation that my machine can't detect cameras properly, and that it might be even a lower-level type of driver I'm struggling with. I know that USB however, does work, because I have have an external drive hooked into the machine. I've gone through the web and tried two hours worth of fixes, without success. I feel like if I can get the Canon camera detected, then the iPhone will be on it's way to being fixed too. BTW, I couldn't really find anything of use in the Event viewer. Any and all suggestions welcome.

  Read the article

• How to set up RAID-0 first time on new PC?

  - by jasondavis

  I have built basic PC's in the past but have never used a RAID array at all. SO now I am buying parts to build my new PC, it will be an intel i7 processor. My motherboard will have RAID support which I will use instead of an aftermarket raid controller for now. Also I plan to use 2 SSD drives in RAID-0 for my windows 7 OS. (Please note that I am aware of the issues with doing this, including lack of TRIM support when using RAID with SSD drives. I am OK with it not working as I can just re[place the drives in a year or so or wheneer they become more sluggish). SO here is my question part. If I assemble the motherboard, PSU, processor, RAM, vidm card, etc and then go to turn the PC on, it will have the 2 SSD drives hooked up. so I assume I will then soon the BIOS screen before I install windows? How to I go about making the 2 drives work in RAID-0 at this point? I do the raid part before installing my OS right? Please help with the steps involved from assembling the parts of the PC and then turning it on, to the part of getting the RAID-0 set up between the 2 drives and then installing my windows 7 OS from a Optical drive? Please help, all advice, instructions, tips appreciated as long as on topic. I do not need to be told that this is a bad idea as far as if 1 drive fails I losse it all, I plan on having a disk IMAGE to be able to restore my OS and software to a new set of drives at anytime needed in the event of drive failure. Same goes for lack of TRIM support. Thanks for reading and help =)

  Read the article

• Hard Drive that was used before not detected or accessible in Windows 7

  - by Anders

  Hello SU: My PC crashed for some unknown reason, and I am still working on what caused that. However, I pulled my main (windows) drive from my computer and hooked it up to my roommate's machine and was able to pull the data I needed off of it (i.e. the drive is good). I hook up his drives as they were, I had to turn off his machine and unplug his secondary drive to hook mine up, boot his machine and there is no second drive available in windows explorer. I opened Device Manager to see if for some reason it's drive letter got un-assigned, but there is nothing listed in there except his primary hard drive, his optical drive and one other optical drive which I believe is the virtual drive Daemon Tools made. The drive shows up in the BIOS, however after I restarted his machine again it sits on the "Entering setup....." screen at the load window. The only thing I can think of is that may have messed with stuff is I used this tutorial to create a bootable XP install on a USB drive to install XP on my machine (I am 99% certain that the optical drive in my PC is broken) and maybe it used the other hard drive's letter for the USB drive for some reason, which doesn't make much sense since it was recognized it as a different drive letter before I started the process. It is possible that it used the secondary hard drive's letter for it's work, but once again I am uncertain. Where should I go from here? He his bound to wake up within the next several hours and will probably flip a lid if I cannot get some sort of handle on this. Any and all help is greatly appreciated. PS: Anyone who helps me get this situated has a beer or two on me, as long as you are in the greater metro Detroit area, or don't mind traveling a bit!

  Read the article

• Why the VPN Network Shake-Up?

  - by Brent Arias

  I can RDP to another machine on my home network, only if I'm not also hooked up to my employer's VPN with the Cisco VPN client. Indeed, I can't even ping the other machine by name in this mode, because ICMP suddenly thinks that ( ping myMachine ) now means ( ping myMachine.myEmployer.com ). Of course there is no machine by that latter name, and so it fails. Even weirder, once I disconnect from the VPN I can again ping myMachine successfully, but ICMP reports the machine by its MAC address instead of its IP address. I don't think I've ever seen ping identify another machine by its MAC address. So two questions: How can I access via RDP/ping the other machine BY NAME on my local network while also connected to the VPN? Why is ping identifying a MAC address for the machine on my home network, instead of an IP address? And how can I change this so that an IP address is reported instead? For question #1, I can indeed access the other machine on my home network by IP address. I suspect if I put the name-IP pair into my HOSTS file, then I would be able to access it even when connected to the VPN. But I wonder if there is another (more elegant) solution?

  Read the article

• Streaming music throughout the house on a budget?

  - by greggannicott

  I was wondering whether anyone knew of a way to stream music throughout a house on a budget? I want to avoid spending any money on this (eg. I don't want to buy a d-link style device). It would be ideal if I could use my existing hardware and some open source software. I have three old(ish) PCs knocking around. I'm happy to stick either Windows or Linux on them. They can all be hooked up to speakers. The ideal solution would result in: the same audio being heard from every device (eg. when you hear a beat on one device, you'd hear it at the exact same time on another (so you don't get any echo)) I'd be able to control the source application (eg. the songs lined up) with my iPhone. I realise I'm being cheeky with those two wishes - but you never know your luck. Am I asking for too much, or is there a piece of software/protocol out there with this purpose in mind? I've been searching for sometime now, but haven't had any joy. Thanks in advance.

  Read the article

• DNS request times out then succeeds on my local network. Why?

  - by Dan

  I have a W2K3 Server that is the Domain Controller and also the DNS server. I wanted to make another DNS zone on my network called "something.local" and then make 'A' records to point requests like 'admin.something.local' and 'www.something.local' to machines on my network. I keep getting DNS timeouts but then after 2 tries it succeeds. Why would this happen? How can I troubleshoot? From my desktop I run: nslookup admin.something.local and get: Server: server.domain.com.au.local Address: 192.168.0.10 DNS request timed out. timeout was 2 seconds. DNS request timed out. timeout was 2 seconds. Name: admin.something.local Address: 192.168.0.191 If I go back the other way: nslookup 192.168.0.191 I get: Server: server.domain.com.au.local Address: 192.168.0.10 Name: admin.something.local Address: 192.168.0.191 My DNS server address is 192.168.0.10. The new DNS zone is not hooked up to active directory. I do not have much experience with DNS. Yesterday it was working fine. I have tried doing an 'ipconfig /flushdns' on both my desktop and the DNS server

  Read the article

• CUPS printer on Vritual Machine can be access via CUPS admin, but not by XP?

  - by SJaguar13

  I have a Zebra label printer connected to a Linux Mint virtual machine. It was set up with CUPS and a Windows XP computer can then print to it via http://192.168.1.76:632/printers/labelprinter. That was all fine and dandy I then hooked up a Fargo Pro L PVC card printer to a Windows XP virtual machine. I had to disconnect the label printer as the server that hosted both virtual machines only has 1 parallel port. Now I plugged in the Zebra again, and it cannot print from the Windows XP computer anymore. If I go to the CUPS admin panel on the Windows XP computer, I can see it, everything looks fine, and I can send it a test page to print which works. If I try to print from Windows, I get an error that the printer is not found/cannot connect to the server. The only other thing that changed was the firewall on the router to allow remote desktop to another computer from outside the network, but all the firewall stuff was for external use. Nothing affected the IP address of the internal network. The Linux Mint VM also had a PDF pritner that was shared with CUPS. That printer is also down. I tried setting up a new CUPS installation on another VM, and when I go to share it with XP, I get the same error. I don't know what to try. It has access, it can get to the admin from that computer, it seems to be up and ready, but when Windows tries to connect, the printer isn't found even though 4 days ago everything was fine. Any ideas?

  Read the article

• Is there a historical computer peripherals or accessories museum or even just a current list?

  - by zimmer62

  Thinking about all the unique and different peripherals I've owned over the years, from ISA capture cards, to parallel port controlled shutter glasses for 3d games. I've seen many many accessory or computer peripherals come and go. The nostalgia of these things is a lot of fun. I tried to find some sort of historical time-line or list but what mostly turned up is computers themselves. I'm more interested in the mice, scanners, the weird adapters that shouldn't exist, short run very rare products, strange devices from computer shows in the 80's and 90's... Hardware you might find in a geeks basement that would be completely useless now, but was the coolest thing around when it was new. An example would be a drawing tablet I had for my TI-99 computer, or the audio tape player accessory for a C64 which let you save files to audio tapes, An ISA card that did the same for PC's hooked up to a VCR. Remember that IBM-PC Jr upgrade kit, that added a floppy drive, more memory and the AT switch in the back? I'd love to find either a wiki, or a list that has already been assembled which contain many of these weird (or common) accessories. I've had so many over the years I suppose I could start a wiki here if such a list doesn't already exist.

  Read the article

• 5.1 Surround Channels are Jumbled

  - by stickynips

  I had this exact setup working previously, but after a reformat it went screwy on me. I have an Onkyo A/V Receiver hooked up to my PC, via optical S/PDIF. Attached to the receiver is a 5.1 speaker setup (tested and working fine with my Xbox via the receiver). It seems to me that the audio channels are getting mixed up somehow between the PC and the receiver. I have a 5.1 test file which plays a sounds through each speaker individually. The channels are mixed as such: "Left Front" plays through my Right Front speaker "Center" plays through my Left Front speaker "Right Front" plays through my Center speaker "Left Rear" plays through my Subwoofer "Right Rear" plays through my Left Rear speaker I've tried downloading the latest Realtek HD Audio Drivers and the Realtek HD Audio Manager, but neither makes any difference. If there's a way I can manually rearrange the channels I believe it would fix the problem, but as far as I know this is impossible. edit: Sorry, I've forgotten some basic info. I'm running Windows 7 x64. The sound card is Realtek ALC892 embedded in a GIGABYTE GA-890GPA-UD3H AM3 motherboard.

  Read the article

• IIS not responding with SSL Server Hello

  - by Damien_The_Unbeliever

  I'm having difficulty getting a particular IIS machine to "do" SSL. This is a test environment (one of many) which we've set up "the same" as we have many times previously, but it just doesn't seem to be working. The server is Windows Server 2003 (Version 5.2 (Build 3790.srv03_sp2_gdr.100216-1301 : Service Pack 2)) IIS is hosting 4 sites (including the default site), but only one site is configured for SSL. We're using the same SSL certificate we use on all of our other servers (it's a wildcard cert). (Don't think this is relevant, but including anyway) We've configured the site to require SSL, it has a subdirectory that doesn't require SSL but has an asp page that redirects into SSL. The 403;4 error page for the site is hooked up to this asp page (this is how we do our non-HTTPS into HTTPS transition). Using Microsoft Network Monitor (3.3), I've just run a session against a server where SSL is working. It can pull apart the SSL exchange as the following messages: SSL: Client Hello SSL: Server Hello. Certificate. Server Hello Done SSL: Client Key Exchange. Change Cipher Spec. Encrypted Handshake Message. SSL: Change Cipher Spec. Encrypted Handshake Message However, on our problem server, I only see: SSL: Client Hello. The next packet from the server (from port 443, so it's listening and responding there) contains only 60 bytes, and just seems to have the Tcp headers and not much else (but I'm by no means an expert at deciphering these things). So, where do I look next? Or what additional information do I need to add to this question, and where do I find it?

  Read the article

• VMWare ESXi 5 - Expanded RAID 5 array - cannot access datastore

  - by Dayton Brown

  I'm using VMWare ESXi 5 and had a 2 TB RAID 5 setup on an HP DL360 with a P400i RAID card. I added two more 1 TB drives and using the SmartStart ACU, added the drives and expanded the logical disk. Now after booting back to ESXi, the server boots, but lists no available persistent storage. I've rescanned multiple times to no avail: the Datastore doesn't show up. I booted to GParted and the 1.8TB partition shows up, but it shows as unknown. Anyone have any good ideas? EDIT: Final Solution So after much gnashing of teeth, it was fairly simple to solve. I purchased an eSata 2 TB external drive and a PCI eSata card for my server. I then used Clonezilla to image the current partitions to my new external drive. You have to check "don't check drive sizes" in advanced mode, otherwise it will yell at you for have a smaller drive. For some reason my PCI card wouldn't boot on my HP server, so I hooked the drive up to another desktop I had, booted to VMWare, and copied the vmdk's to another drive. I'm going to blow out the RAID config and then create 1.5TB logical drives.

  Read the article

• All network devices freezing when Airport Extreme Base Station is connected. Any ideas?

  - by Jon

  I've been troubleshooting this issue for a while, and through a series of events have it narrowed down to my airport extreme base station. I like this router, since I'm able to connect to IPV6 sites without any insane configuration (my alternate router is too old and doesn't support v6). My question is: Has anyone else had this issue, if so how is it resolved? If not, can you recommend a good IPv6 router? Here is how I came to the conclusion that it is the router: Devices: XBOX 360, HTC Incredible, Home-Built machine running FreeBSD, Home-Built machine running Ubuntu 10.04. 1.) Noticed freezing on Ubuntu Box. 2.) Noticed freezing on XBOX360 3.) Noticed freezing on HTC Incredible (only when connected to my network wirelessly). The above all happened at random times throughout the past few weeks. Over the last few days, I was playing XBOX and noticed that the XBOX and Ubuntu machines both froze. I picked up my phone, and it was also frozen. I reset all devices, power-cycled my router, and all was fine again. About two hours later, it happened again (I was playing Forza III, the XBOX froze; I went to the Ubuntu box and it was frozen; unfortunately, the HTC phone was not connected wirelessly, and the FreeBSD box was turned off). I can't even begin to imaging what a router could be doing to freeze devices with such differing hardware/software/OS, and I feel absurd for coming to this conclusion, but I have nothing else. I hooked up my archaic Netgear router, and have had no problems since. :(

  Read the article

• vSphere Promiscuous mode only receiving packets one way from network switch

  - by steve.lippert

  We have two network switches, a POE switch (SwitchA) to power our phones / users computers and a non-POE switch (SwitchB for the rest network.) Each switch is setup to do port mirroring to support our VoIP recording system. SwitchA does port mirroring on specific ports if we need to record a user. SwitchB mirrors one port to monitor our work at home users (Internet comes in from managed router, to switch, back out to our firewall.) These two port mirroring setups feed into one vmware vSphere 4.1 server, it has four total physical cards. The other two NICs feed into an unmanaged switch for connecting to the rest of the network. Once into the vSphere server all network ports go into a vSwitch, and then one of the servers (Windows 2008 R2) sniffs them out and does its thing. Everything is working fine and dandy from SwitchB. But on SwitchA we only receive one side of the VoIP packets (going out to the phone, nothing coming in from the phone). Troubleshooting steps I have taken so far: I hooked up my laptop to the monitor port on SwitchB and I see both sides of the packets. I swapped which network interface is plugged into the monitor port on SwitchA. Because everything feeds into one vSwitch / vNetwork and both sides of the conversation arrive just fine from SwitchB I believe everything is configured correctly on the vSphere server/guest. What could be causing one way packets to arrive on my guest machine from only one interface, but not the other? Could a bad cable be causing the problems from SwitchB?

  Read the article

• Can't access server sound card when vnc'd into ubuntu server

  - by Corey Kennedy

  I've set up my ubunutu 10 server with xfce, nxserver, and now tightvncserver so that I can control it remotely from my Windows 7 laptop. NX is working fine for remote access, but when I run (for example) exaile, no sound will be sent through the server's sound card. I installed tightvncserver and connected, but ran into the same problem. Exaile opens, sound isn't muted, I can see that sound cards are installed (via cat /proc/asound/cards), but I can't seem to get the remote sessions to access the server's sound card. Also, just to confirm that the sound card was working I hooked up a montior/keyboard to the server and opened a local xfce session. That worked fine. While I had the local session running, I was also able to open a remote session with NXClient and start exaile - which then successfully piped sound to the local card. After disconnecting the monitor/keyboard and moving the box back to its normal spot, though, I was not able to play sound via either an NX or VNC session. Does anyone have any suggestions? Surely it's possible to configure my remote sessions to pipe sound to the server's sound card, right? Or at least get xfce up and running without a monitor or keyboard but with access to the sound card so I can VNC into it? Thanks!

  Read the article

< Previous Page | 11 12 13 14 15 16 17 18 19 20 21  | Next Page >