Search Results

Search found 1543 results on 62 pages for 'motherboard'.

Page 15/62 | < Previous Page | 11 12 13 14 15 16 17 18 19 20 21 22  | Next Page >

  • GA-P55A-UD4 SYSFAN 2 problem....

    - by Vit
    Hi, I have some strange problems with the mobo in title. I have two fans connected to SYSFAN 1 and 2. Both are the same temp regulated Arctic Cooling F12. They are regulated thru temp sensor which is in different cable from fan. It connects to the 3 pin. So, I connected them to SYSFAN 1 and 2 MB ports. The problem is, when PC starts, the fan connected to SYSFAN 1 spins nice and is reporting speed to BIOS. But second fan connected to SYSFAN 2 starts to spin, than stops. I tried to warm the sensor with no help. Also, in BIOS I found no feature about SYSFAN 2 mode or something. I tried the fan itself by connecting it to PWR fan connector and it works fine. But obviously I want it to operate in SYSFAN 2. Please if you have any advice, help. Thanks.

    Read the article

  • Building a workstation computer for Image processing? [closed]

    - by echolab
    I am taking a gigapixel image my goal is 50gigapixel and shooting is almost done , i am doing some research to build a workstation so i can stitch images together , my questions is ! Could u suggest some dual cpu mainboard that works fine with xeon 5500+ , with 64GB+ ram support ? My other question is which hardware is most important in image processing , all i see in story of gigapixel panoramas is they have dual xeon and 32gb+ ram ? i wonder if i am doing this right , i mean they don't post information on graphic card , mainboard and stuff ! I did asked several websites , but nothing best answer was get some high-end workstation and plenty of hours , i don't want to purchase ready to use workstations, i wanna build it up Thanks in advance

    Read the article

  • New mainboard for Shuttle

    - by Dave Arkell
    I have an old Shuttle barebones SN21G5 (AMD 64), and I really need a more modern chip in there. Is there a way of swapping out the old mainboard and putting in one of those new fangled phenom mainboards in there?

    Read the article

  • Suppliers for revision-controlled hardware, long-life motherboards?

    - by jacobsee
    Has anyone had good experience with suppliers of industrial computers, specifically 'long-life, revision-controlled' motherboards? I'm found a couple of likely candidates including ITOX, BCM, and DuroPC but haven't been able to find much in the way of independent review. I'm currently using off the shelf motherboards for an industrial data-acquisition system and am trying to eliminate the problem of rapid turnover/obsolescence of motherboards.

    Read the article

  • Laptop does not charge old or new battery with Old and New AC adapters.

    - by Jeff
    My Sager computer has been having a strange issue with the charging. For a long time it would be working perfectly as long as I was active on it. After I'd leave idle for a while it would suddenly decide it didn't want to use AC power anymore and would just discharge the battery until it shutdown because of low battery levels. Was not a huge deal to me since I just sent it to standby when done with it and it worked fine. Recently, however, it would not detect AC power while the battery was in. It ran from the battery just fine but until you powered it down, unplugged the battery, then plugged in the AC adapter it would not be on AC. In addition if I plug the battery back in after it's on AC power, it will see it but the battery won't charge though it can still discharge it. This is OS independent. I tried both a replacement battery and a replacement AC adapter. Neither solved my issue. I'm fairly comfortable opening and servicing a laptop but I don't know where to start. I'd like to avoid replacing my system board if possible. Any Ideas?

    Read the article

  • What desktop boards support VT-D or IOMMU?

    - by Jeff Shattock
    I'm looking for a desktop board that supports either VT-D (Intel) or IOMMU (AMD) technology. This is the IO virtualization technology, not VT-x for CPU virtualization. I've found a list of chipsets that are purported to have this, but every board I look at, the vendor has decided to not support that feature. I would really prefer a desktop board over a server board for this. Does anyone have a specific model that is known to support this technology?

    Read the article

  • Any way to tell apart a CPU defect from a mainboard defect?

    - by Pekka
    I have a fairly modern desktop computer, an AMD Athlon II X2 based silent PC, that does not work. When turned on, it will start physically (all fans are rotating, disks start up...) but not give a signal on any of the graphics ports (DVI, VGA, and HDMI, I tried all three). Also, the reset button does not seem to have any effect. I have stripped the mainboard bare of all SATA connections, extension cards, and the one 2GB RAM chip to eliminate them as the problem source, but to no avail, so I think it's fair to assume it's either the mainboard or the processor that are at fault. However, I have neither a replacement mainboard, nor a replacement processor handy to identify which one is broken. The cause of the defect is unknown, so for all I know, it could be both. Therefore, I'm reluctant to buy replacement hardware blindly before knowing more. Is there any way to further diagnose (or at least get some indication) which component is broken without buying replacement hardware?

    Read the article

  • Does a modern PC require a graphics card to run?

    - by ArtM
    As I can remember, on old systems (Pentium II or III) it was not possible to boot and run the PC if the graphics card was missing (AGP cards were used in those days). Many years from then, I'm using motherboards with integrated graphics and I have no experience related to this subject, the "graphics card" always was present. Currently I intend to build a home/private "server" for my purposes and most of the motherboards I want to buy have no integrated graphics (AMD 870 or 970). I can take a normal graphics card from my firends for a few hours/days and use it when installing the necessary software. The question is: can I boot and run the PC without problems after I install everything I need and the graphics card is removed? if a general answer cannot be given, at least some examples of manufacturers/MB series/MB models will be helpfull I think it's obvious, but for completeness: I mean cheap desktop components, not real servers.

    Read the article

  • Removing BIOS Post Messages

    - by Steve
    I am working on a project where a standard x86 desktop system will boot and run a single program until it is shut down. I would like to remove all the bios post messages so that it looks a little more "finished" and cleaner when it starts up. I was hoping that there might by a standard implementation/terms to know about so I can avoid having to dig through every manual to see if there are options, or get some advice on a standard set of tools I should be using. I was thinking about getting a board that has an image that covers up the post messages until you press a key and trying to customize it to all black, but it's not clear if this is a good direction. I started looking for OEM motherboards but my searches were filled with standard commercial stuff, or seemed to be way to big for my toy project. What is the best way to go about removing all the bios post messages and just having a blank screen or "loading" message until OS loads?

    Read the article

  • Received a RAMPAGE IV FORMULA MOBO. Possible CPU Socket problems

    - by Tantan
    I recently received a Rampage IV Formula MOBO in a trade. From everything I read online this seems like a pretty nice piece of hardware. There's one thing I'm worried about though. It appears as though the socket where the CPU goes might have some bent/missing pins. I'm not exactly a computer expert and I wanted to know if this could be any sort of problem. I would post a picture but I apparently don't have enough rep for that... Also, if I did want to move my current rig onto the new MOBO would it even be worth it? MY CURRENT COMPUTER SPECS i3-3220 CPU 8GB DDR3 RAM GeForce GTX460 GPU With a Biostar MOBO!

    Read the article

  • Does the Intel DX79TO motherboard support x8 devices (SAS HBAs) on PCIe x16 slots?

    - by Zac B
    Context: I have an Intel DX79TO motherboard and a Sun SAS3081E-S/LSI 1060E-S HBA card with a PCIe x8 interface. I plug the HBA into my mobo next to my graphics card, and the HBA power lights illuminate, but the BIOS and OSes (tried Linux, ESXi, Win7) don't see the HBA at all. Question: Does the DX79TO motherboard support non-x16/non-GPU devices in its PCIe x16 slots? According to this question, some consumer motherboards don't support this, but I can't figure out whether or not this motherboard/family does. The answer will affect whether I buy a new motherboard or RMA the SAS card, with money attached to each course, so I figured I'd ask here first. What I've Tried: I've read the spec/manuals for the motherboard and the HBA, and I didn't see anything regarding whether or not the x16 slots were back-compatible to lower lane widths/non graphics-card devices, or whether or not the card could run in wider slots than x8. I've tried contacting Intel, but that was over a month ago and I haven't yet heard anything back except an automated "we got your email!" message.

    Read the article

  • Why does my motherboard go through an endless reboot cycle when 8 GB of memory is attempted vs 6 GB?

    - by nizm0
    I never got an answer in my googling to this about a year ago and have an extra stick of memory I'd like to be able to use. When is inserted the computer starts, and then reboots immediately in an endless reboot cycle. As soon as the 4th stick is removed, the computer works fine. Right now I have 6 GB of my 8 GB installed. Is there a solution that I am missing to enabling this motherboard to actually boot up with all 8 GB (it supports it). Right now it won't even boot up to BIOS with the 4 sticks... only 3? Memory: 1 x G.SKILL 4 GB (2 x 2 GB) 240-Pin DDR2 SDRAM DDR2 1100 (PC2 8800) Dual Channel Kit Desktop Memory Model F2-8800CL5D-4GBPI - Retail (URL: ) http://www.newegg.com/Product/Product.aspx?Item=N82E16820231194 Motherboard: 1 x GIGABYTE GA-EP45-UD3R LGA 775 Intel P45 ATX Intel Motherboard - Retail ( URL: )http://www.newegg.com/Product/Product.aspx?Item=N82E16813128359

    Read the article

  • Are there any issues with using an ATI 5870 on an nVidia motherboard?

    - by Liam
    I have an Alienware machine, so I'm not entirely sure on the make of motherboard, however, I do know it's got nforce on it and allows me to use nVidia cards in SLI. My 8800GTX has recently died and I'm looking to buy a replacement - I'm considering the ATI 5870, but what I want to know is, if I choose this card, does it mean I will need to change motherboard just to change graphics card vendor or does it not matter?

    Read the article

  • Laptop GPU apparently blew up, motherboard doesn't even turn on its power LED. [But..]

    - by leladax
    EDIT: (Was: Laptop automatic shutdown after 2 seconds) If I take out the GPU, the motherboard LED turns on but then [if it attempts to power up and boot] it turns off after 2 seconds [fans turn on normally in that short period]. [Without the GPUs out there's not even an attempt to boot.] It's an SLI motherboard for a toshiba (model X200-219). If I take out one of the GPUs (they are on top of each other) it surprisingly lets the motherboard turn on too (as it is if both are out) but it still turns off after 2-3 seconds, same behavior. I wonder if it's the GPU that produces the 'turn off after being on' behavior and not something else. [Has anyone seen this behavior with blown up GPUs or could it be something else?] Previous question (before EDIT. Sorry, but someone thought it productive to lock the other one as duplicate): I'm trying to insvestigate which component produces this behavior. Other indications show it may be the GPU but I wonder if anyone knows more. It's a Toshiba Satellite X200 description: AC power shows the power being fed normally, when turned on the fan works and it appears to be starting up but after 2 seconds it shuts down with only the 'AC power connected" led on. -- seconds are about up to 4,maybe not 2 exactly.

    Read the article

  • Can I use a mini PCI-E card in a standard motherboard with PCI/PCI Express slots?

    - by White Phoenix
    I'm helping someone build a computer and they absolutely insist on having an internal Bluetooth adapter. I've been searching around for a PCI-E/PCI based Bluetooth adapter but I've had no luck finding one - I've found some discontinued ones but they have giant antennas coming out the back - the person I'm building the computer for doesn't want that. I've been repeatedly insisting on him simply getting a USB Bluetooth dongle, but he doesn't want one taking up his external USB slots. This is the motherboard I'm using for his build: http://www.newegg.com/Product/Product.aspx?Item=N82E16813157303 My question is if it's possible to use one of those laptop PCI-E cards in a motherboard like this that has PCI-E and PCI slots, or if the form factor is completely different and won't fit?

    Read the article

  • Z77 Motherboard with i7-2600K cpu, what will not work?

    - by Mxx
    I'm building a new system. So far I think I narrowed it down to Gigabyte GA-Z77X-UD5H (Z77 Ivy Bridge chipset) motherboard. I was planning to get i5-3570K(Ivy Bridge) cpu, but now I can get i7-2600K(Sandy Bridge) cpu for free. It is my understanding that Ivy Bridge platform brings support for PCIe3 and (additional?)USB3 ports. If I were to put SB cpu into IB motherboard, what is going to happen to PCIe3 slot? Will it not work at all or downgrade to PCIe2? Also, what is the situation with USB3 ports?

    Read the article

  • Where should I plug in my monitor -- Motherboard or Graphics card?

    - by Jeremy White
    Assuming I am using the following equipment... motherboard with HDMI/DVI & no embedded graphics discrete graphics card (nVidia or ATI) on PCI-E slot Intel CPU with integrated graphics ...where should I plug my monitor into the computer? Presumably, I'll get the fastest speed on games connected directly to the graphics card. But there is also power savings when connecting to the motherboard and accessing the Intel on-board graphics. I've read that some motherboards can switch automatically between the Intel graphics and discrete graphics. Is that something that works well, and where do I connect the monitor to enable that?

    Read the article

  • PC powers off at random times

    - by Timo Huovinen
    Short Version After experiencing some problems with Mobo batteries my PC started to power off at random times, the power off is instant and sudden and does not restart afterwards, need help figuring out the cause. Facts: Powers off when PC is playing games Powers off when PC is idle Powers off when PC is in safe mode Powers off when PC is in BIOS Powers off when PC is booted through a Windows installation USB Replaced the motherboard battery several times Replaced the 650W PSU with a 750W PSU Replaced the RAM Swapped the RAM between slots Re-applied thermal paste to the CPU Checked if the motherboard touches the case Nothing is overclocked PC Specs PC specs: OS: Windows 7 Ultimate SP1 RAM: klingston 1333MHz 4GB stick CPU: AMD Phenom II x4 955 Mobo: Gigabyte 88GMA-UD2H rev 2.2 Motherboard battery: CR2032 3v HDD: 500GB Seagate ST3500418AS ATA Device Graphics: ATI/AMD Radeon HD 6870 Very Long version Around 10 months ago I built a brand new gaming PC. Around 6 months ago it's time setting in windows started resetting to the year 2010. I swapped the Motherboard battery for a new one of the exact same size and shape and voltage, and the problems disappeared...for around 2 weeks. Then the same problem happened again, time gets reset, I swapped the battery again, and the problem was gone for good and everything was great for about 3 months.. then another problem started happening, the PC started to power off suddenly and without warning at completely random times, sometimes the PC works for and hour, sometimes 5 minutes. So I read on the forums that it might be either the PSU or the motherboard Battery or RAM or HDD or the Graphics card or the CPU or the motherboard or the drivers or a Virus or Grounding issues, or something short circuiting, basically it can be anything... I spent some days researching, and decided to remove the possibility of a virus. I reset the CMOS, cleared all BIOS settings and reinstalled windows 7 after a full format of the HDD, but the random power off kept happening. I then disabled the restart on error option in windows and looked at the event log for error events, but they did not help me figure out the problem. Network list service depends on network location awareness the dependency group failed to start Source Kernel Power Event 41 Task Category 63 Source Disk Event ID 11 Task Category None The driver detected a controller error on device disk I took apart the PC, every little piece, re-applied some expensive thermal paste to the CPU, and double checked that none of the pieces are touching the PC case. The problem was gone, the PC no longer powered off randomly I re-attached the graphics card and all was good for 4 months... then the power off problem appeared again, but was happening at high intervals, the PC would shutdown once in 2 days on average, at random points in time, sometimes when it's idle all day long, sometimes when it's running CRYSIS 2. I checked the CPU temperature, because I know that AMD CPU's have a built in protection mechanism that switches off the PC if the CPU gets too hot, and the Temp was 50C system temp, and 45C CPU after running the PC all day long (I did not do tests to see if there are any temperature spikes, don't know how to do them) Originally the PSU that powered the PC was 650Watts and had one 4 pin cable to power the CPU, I replaced it with a new 750Watts PSU which has two 4 pin cables for the CPU, but the problem remained. I removed the graphics card and let the motherboard use the built in one, but the PC kept suddenly powering off at random times. I took apart the PC completely again, and re-applied thermal paste to the CPU, added lots of insulation, and checked for any type of short-circuit possibility again and again, but the problem remained. The problem was like that for some months. I replaced the Battery a couple of times over the time, changed lots of options in windows, and tried everything I could, but it kept powering off, so I stopped using the PC as much as I used to, just living with the random power offs from time to time, until a couple of days ago, when the power off happens almost immediately after powering on the PC. I replaced the RAM with a brand new one, but that did not help. Took apart the PC again, checked for anything anywhere that might cause it, found some small scratches on the very edge of the motherboard to the left of the PCI express x16 slot. This might cause the problem, I thought, but the scratch looks very superficial, not deep at all, and if the scratch did harm the motherboard, wouldn't it cause it to not start at all? And why did it start to power off a while ago, and then suddenly stop powering off? The scratches could not have vanished??? did chkdsk \d but it powered off when it was at 75% I removed the hard disks, the graphics card, while I fiddled with the BIOS settings, and suddenly the PC shut down while I was looking at the BIOS version. This makes me realize, it is not caused by: HDD, Windows, Drivers or the Graphics card I cleared the CMOS again, updated the BIOS from F5 to F6f beta, but that did not help, it might even seem that the PC powers off even sooner. The shutdown even happened to me while I booted through a windows 7 installation USB and was in the repair console. I removed one of the cables powering the CPU, now only one 4pin cable powers it, and it worked for 30mins after doing that, which makes me think that it's the CPU overheating, and because it gets less power, it overheats slower? The things that I am still considering: CPU overheating (does not seem to overheat, maybe false readings?) Motherboard short circuiting (faulty motherboard?) I desperately need some advice in what is faulty, is it a faulty Motherboard or an overheating CPU? or maybe something else? I have been breaking my head over this problem over a span of 6 months. I'm not sure if this is a good place to ask this question, if it is not, then tell me where I can get some experienced help. More info I have also discovered a mysterious piece that seems to have fallen out of the motherboard i119.photobucket.com/albums/o126/yurikolovsky/strangepiece.jpg What is it? Looks like each time that it powers off the datetime gets reset I also found another forum post tomshardware.co.uk/forum/… except I don't have Integrated PeripheralsUSB Keyboard Function option in BIOS :S Comments summary (asked by Random moderator) Q. tell me, if the computer restarts, is it immediately? Does it take a second and then restarts? Do you see (BSOD) or hear (PSU, short circuit) any suspicious when it happens? After reading trough it, it remains the mainboard that is faulty. – JohannesM A. Immediate power off, all the fans stop instantly, all the light turn off instantly, no sound or anything, and it remains off until I turn it back on. Thanks for the feedback, faulty motherboard is what I fear. Q. Try stress-testing the system with Prime95 and see if errors or shutdowns occur when the CPU is under full load. – speakr A. Prime95 heat stress test peaked CPU heat at 60C after 5mins, it powered off after 30mins of testing in the middle of the test with no errors, Prime95 Heat test or the stress-testing with low RAM usage (small or in-place FFTs) do not report errors while testing for 10-60 mins. The power off does not seem like it is affected by Prime95 at all Makes me wonder if it's a CPU or Motherboard issue at all. Q. I had similar random/intermittent problems with my old board. It gave one of a few different symptoms: keyboard and/or mouse would die and/or the RAM wouldn't work and/or it would shut down. It was in bad shape. One problems was that my old PSU had literally burned the connector on it (browned around the pins), another was that a broken lead inside the layers of the PCB would work sometimes if it happened to be hot or if I bent the board—by jamming a hunk of wood behind it. I managed to keep the board alive for several years, but eventually nothing I did would make it work correctly anymore. – Synetech A. I will try that as the last resort, ok? ;) Q. Have you tried a different power cord, surge protector, outlet (on a different circuit). It's worth a shot just to ensure it's not subpar wiring or a week circuit (dips in power may cause shutdown if the PSU can't pull enough juice from the wall). – Kyle A. yes, I attached the PC to an entirely different outlet on a different circuit and the problem persists. After connecting it to a different outlet after starting the PC it gave me 3 long beeps and 1 short one, then the PC immediately proceeded to boot up normally. Q. Re-check your mainboard manual and all PSU connections to your mainboard to be sure that nothing is missing (e.g. 12V ATX 4-pin/6-pin connector). If you can provoke shutdowns with Prime95, then consider buying new hardware -- a stable system should run Prime95 for 24h without any errors. Prime95 mentions errors in the log when they occur and gives a summary after the stress test was stopped manually (e.g. "0 errors, 0 warnings", if all is fine) – speakr A. Re-checked, there are no more PSU connectors that I can physically connect, except the one ATX 4-pin (there are 2 that power the CPU) that I disconnected on purpose, I have reconnected it but the problem persists. Q. With one PC I had a short curcuit. The power button on the front plate had its cables soldered, but not isolated, and the contacts were very close to the metal case. A heavier touch was enough to cause a shutdown. The PC's vibration could be enough – ott-- A. yes, it seems to switch off with even the lightest touch, I switched on the PC, then pulled out the front panel power cable that connects to the motherboard so the power button does not work anymore, after 5 mins of working like that, with the power button completely disconnected, just sitting idle, the PC powered off again, I don't think it's the power button. Q. I wonder if you dare to operate components without the case, that is remove motherboard, power, disk ( just put the motherboard on a wooden desk). Don't bend the adapters when running like that. – ott-- A. yes, I do dare to do that, but only tomorrow, too tired/late right now.

    Read the article

  • Motherboard Dying? AHCI Drive Init and boot loop intermittent failure

    - by Adam Heath
    My computer is now intermittently failing to boot up. For the last couple of days, when I turn it on it hangs on "AHCI Drive Init...", and when powered off and on again, it booted up fine. Today, it did the same but failed in a few other ways too, seemingly at random: Hangs on "AHCI Drive Init..." Boot loop (after "AHCI Drive Init..." appears for a split second (no drives listed)) Black screen (after "AHCI Drive Init..." appears for a split second, a black screen with all fans still running) The interesting part is that the above is not affected by what drives are connected, or what to. I have tried both disks, each disk individually and no disks (along with trying the primary and secondary SATA controllers), none of this has any effect on what happens. After about 20+ attempts of different combinations, it suddenly decided it would boot up into Windows, and I hadn't touched anything for about 2 cycles. Motherboard: Gigabyte GA-870A-USB3 Processor: Amd Phoenom II x6 1090T RAM: 8GB Corsair 1600 Primary Disk: Plextor 128GB SSD Secondary Disk: Western Digital Black 1TB OS: Windows 8.1 Is this my motherboard dying? Or could something else be the cause? Thanks!

    Read the article

  • MacBook Pro Late 2009 SATA Resets, Slowness (Is my motherboard dying on both machines?)

    - by A Student at a University
    My MacBook Pro runs slower the longer it's on. I am getting kernel warnings. Some, but not all, resets correlate with AC power connects and disconnects. I don't think the warnings do. (How do I tell?) What are these errors? What causes them? Can this damage the drive or corrupt data? What is it seeing that motivates these? 02:37:16[ 0.791992] ahci 0000:00:0b.0: PCI INT A -> Link[LSI0] -> GSI 20 (level, low) -> IRQ 20 02:37:16[ 0.792047] ahci 0000:00:0b.0: irq 43 for MSI/MSI-X 02:37:16[ 0.792053] ahci 0000:00:0b.0: controller can't do PMP, turning off CAP_PMP 02:37:16[ 0.792104] ahci 0000:00:0b.0: AHCI 0001.0200 32 slots 6 ports 1.5 Gbps 0x3 impl IDE mode 02:37:16[ 0.792107] ahci 0000:00:0b.0: flags: 64bit ncq sntf pm led pio slum part boh 02:37:16[ 0.792111] ahci 0000:00:0b.0: setting latency timer to 64 02:37:16[ 0.813473] scsi0 : ahci 02:37:16[ 0.823340] scsi1 : ahci 02:37:16[ 0.848164] ata1: SATA max UDMA/133 abar m8192@0xe7484000 port 0xe7484100 irq 43 02:37:16[ 0.848166] ata2: SATA max UDMA/133 abar m8192@0xe7484000 port 0xe7484180 irq 43 02:37:16[ 1.190132] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16[ 1.190153] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16[ 1.213568] ata1.00: ATA-8: OCZ-VERTEX2, 1.23, max UDMA/133 02:37:16[ 1.213572] ata1.00: 195371568 sectors, multi 1: LBA48 NCQ (depth 31/32) 02:37:16[ 1.227293] ata2.00: ATA-8: ST9500420ASG, 0002SDM1, max UDMA/133 02:37:16[ 1.227297] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) 02:37:16[ 1.229570] ata2.00: configured for UDMA/133 02:37:16[ 1.240120] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5850000 action 0xe frozen 02:37:16[ 1.240123] ata2: irq_stat 0x00000040, connection status changed 02:37:16[ 1.240127] ata2: SError: { PHYRdyChg CommWake LinkSeq TrStaTrns DevExch } 02:37:16[ 1.240133] ata2: hard resetting link 02:37:16[ 1.260738] ata1.00: configured for UDMA/133 02:37:16[ 1.280111] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5850000 action 0xe frozen 02:37:16[ 1.280114] ata1: irq_stat 0x00000040, connection status changed 02:37:16[ 1.280118] ata1: SError: { PHYRdyChg CommWake LinkSeq TrStaTrns DevExch } 02:37:16[ 1.280122] ata1: hard resetting link 02:37:16[ 1.990101] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16[ 1.994215] ata2.00: configured for UDMA/133 02:37:16[ 1.994220] ata2: EH complete 02:37:16[ 2.030097] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16[ 2.090773] ata1.00: configured for UDMA/133 02:37:16[ 2.090778] ata1: EH complete 02:37:16[ 2.090931] scsi 0:0:0:0: Direct-Access ATA OCZ-VERTEX2 1.23 PQ: 0 ANSI: 5 02:37:16[ 2.091045] sd 0:0:0:0: Attached scsi generic sg0 type 0 02:37:16[ 2.091121] sd 0:0:0:0: [sda] 195371568 512-byte logical blocks: (100 GB/93.1 GiB) 02:37:16[ 2.091159] scsi 1:0:0:0: Direct-Access ATA ST9500420ASG 0002 PQ: 0 ANSI: 5 02:37:16[ 2.091163] sd 0:0:0:0: [sda] Write Protect is off 02:37:16[ 2.091165] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 02:37:16[ 2.091183] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA 02:37:16[ 2.091252] sd 1:0:0:0: Attached scsi generic sg1 type 0 02:37:16[ 2.091446] sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB) 02:37:16[ 2.091580] sd 1:0:0:0: [sdb] Write Protect is off 02:37:16[ 2.091582] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 02:37:16[ 2.091637] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA 02:37:16[ 2.093140] sd 0:0:0:0: [sda] Attached SCSI disk 02:37:16[ 2.093773] sd 1:0:0:0: [sdb] Attached SCSI disk 02:37:16[ 2.693899] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null) 02:37:16[ 5.483492] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro 02:37:16[ 7.905040] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null) 02:37:25[ 19.553095] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:37:25[ 19.555266] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:37:25[ 19.641532] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen t4 02:37:25[ 19.641532] ata1: irq_stat 0x00000040, connection status changed 02:37:25[ 19.641532] ata1: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:37:25[ 19.641533] ata1: hard resetting link 02:37:25[ 19.642076] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen t4 02:37:25[ 19.642078] ata2: irq_stat 0x00000040, connection status changed 02:37:25[ 19.642081] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:37:25[ 19.642084] ata2: hard resetting link 02:37:26[ 20.392606] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:26[ 20.392610] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:26[ 20.396697] ata2.00: configured for UDMA/133 02:37:26[ 20.396703] ata2: EH complete 02:37:26[ 20.451491] ata1.00: configured for UDMA/133 02:37:26[ 20.451498] ata1: EH complete 02:37:30[ 24.563725] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:37:30[ 24.565939] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:37:30[ 24.627236] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5900000 action 0xe frozen t4 02:37:30[ 24.627240] ata1: irq_stat 0x00000040, connection status changed 02:37:30[ 24.627242] ata1: SError: { Dispar LinkSeq TrStaTrns DevExch } 02:37:30[ 24.627246] ata1: hard resetting link 02:37:30[ 24.632241] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen t4 02:37:30[ 24.632244] ata2: irq_stat 0x00000040, connection status changed 02:37:30[ 24.632247] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:37:30[ 24.632250] ata2: hard resetting link 02:37:31[ 25.372582] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:31[ 25.382615] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:31[ 25.386782] ata2.00: configured for UDMA/133 02:37:31[ 25.386788] ata2: EH complete 02:37:31[ 25.431668] ata1.00: configured for UDMA/133 02:37:31[ 25.431674] ata1: EH complete 02:45:54[ 529.141844] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:45:55[ 529.544529] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:45:55[ 529.622561] ata1: limiting SATA link speed to 1.5 Gbps 02:45:55[ 529.622568] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5850000 action 0xe frozen 02:45:55[ 529.622572] ata1: irq_stat 0x00400040, connection status changed 02:45:55[ 529.622576] ata1: SError: { PHYRdyChg CommWake LinkSeq TrStaTrns DevExch } 02:45:55[ 529.622583] ata1: hard resetting link 02:45:55[ 529.622609] ata2: limiting SATA link speed to 1.5 Gbps 02:45:55[ 529.622613] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen 02:45:55[ 529.622616] ata2: irq_stat 0x00000040, connection status changed 02:45:55[ 529.622620] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:45:55[ 529.622624] ata2: hard resetting link 02:45:56[ 530.380135] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:56[ 530.380157] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:56[ 530.384305] ata2.00: configured for UDMA/133 02:45:56[ 530.384314] ata2: EH complete 02:45:56[ 530.399225] ata1.00: configured for UDMA/133 02:45:56[ 530.399233] ata1: EH complete 02:45:58[ 532.395990] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:45:58[ 532.518270] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:45:58[ 532.590968] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5840000 action 0xe frozen t4 02:45:58[ 532.590973] ata1: irq_stat 0x00000040, connection status changed 02:45:58[ 532.590977] ata1: SError: { CommWake LinkSeq TrStaTrns DevExch } 02:45:58[ 532.590983] ata1: hard resetting link 02:45:58[ 532.591034] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen t4 02:45:58[ 532.591037] ata2: irq_stat 0x00000040, connection status changed 02:45:58[ 532.591041] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:45:58[ 532.591045] ata2: hard resetting link 02:45:59[ 533.340147] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:59[ 533.340168] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:59[ 533.344416] ata2.00: configured for UDMA/133 02:45:59[ 533.344424] ata2: EH complete 02:45:59[ 533.360839] ata1.00: configured for UDMA/133 02:45:59[ 533.360847] ata1: EH complete 02:45:59[ 533.584449] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:45:59[ 533.586999] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:45:59[ 533.660117] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen 02:45:59[ 533.660122] ata2: irq_stat 0x00000040, connection status changed 02:45:59[ 533.660126] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:45:59[ 533.660132] ata2: hard resetting link 02:45:59[ 533.660141] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5850000 action 0xe frozen 02:45:59[ 533.660143] ata1: irq_stat 0x00000040, connection status changed 02:45:59[ 533.660147] ata1: SError: { PHYRdyChg CommWake LinkSeq TrStaTrns DevExch } 02:45:59[ 533.660151] ata1: hard resetting link 02:46:00[ 534.412536] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:00[ 534.412562] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:00[ 534.416768] ata2.00: configured for UDMA/133 02:46:00[ 534.416777] ata2: EH complete 02:46:00[ 534.431396] ata1.00: configured for UDMA/133 02:46:00[ 534.431401] ata1: EH complete 02:46:03[ 537.384649] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:03[ 537.504214] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:03[ 537.585992] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5900000 action 0xe frozen t4 02:46:03[ 537.585996] ata1: irq_stat 0x00000040, connection status changed 02:46:03[ 537.585999] ata1: SError: { Dispar LinkSeq TrStaTrns DevExch } 02:46:03[ 537.586002] ata1: hard resetting link 02:46:03[ 537.586028] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen t4 02:46:03[ 537.586030] ata2: irq_stat 0x00000040, connection status changed 02:46:03[ 537.586033] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:46:03[ 537.586036] ata2: hard resetting link 02:46:04[ 538.330147] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:04[ 538.330168] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:04[ 538.334389] ata2.00: configured for UDMA/133 02:46:04[ 538.334398] ata2: EH complete 02:46:04[ 538.343511] ata1.00: configured for UDMA/133 02:46:04[ 538.343519] ata1: EH complete 02:46:04[ 538.456413] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:46:04[ 538.459404] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:46:04[ 538.540138] ata1.00: limiting speed to UDMA/100:PIO4 02:46:04[ 538.540144] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5850000 action 0xe frozen 02:46:04[ 538.540148] ata1: irq_stat 0x00000040, connection status changed 02:46:04[ 538.540153] ata1: SError: { PHYRdyChg CommWake LinkSeq TrStaTrns DevExch } 02:46:04[ 538.540159] ata1: hard resetting link 02:46:04[ 538.540202] ata2.00: limiting speed to UDMA/100:PIO4 02:46:04[ 538.540207] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen 02:46:04[ 538.540211] ata2: irq_stat 0x00000040, connection status changed 02:46:04[ 538.540215] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:46:04[ 538.540220] ata2: hard resetting link 02:46:05[ 539.290054] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:05[ 539.290041] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:05[ 539.294100] ata2.00: configured for UDMA/100 02:46:05[ 539.294106] ata2: EH complete 02:46:05[ 539.314125] ata1.00: configured for UDMA/100 02:46:05[ 539.314132] ------------[ cut here ]------------ 02:46:05[ 539.314140] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 02:46:05[ 539.314144] Hardware name: MacBookPro5,3 02:46:05[ 539.314146] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 02:46:05[ 539.314221] Pid: 202, comm: scsi_eh_0 Tainted: P 2.6.35-25-generic #44-Ubuntu 02:46:05[ 539.314224] Call Trace: 02:46:05[ 539.314233] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 02:46:05[ 539.314237] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 02:46:05[ 539.314242] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 02:46:05[ 539.314246] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 02:46:05[ 539.314256] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 02:46:05[ 539.314261] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 02:46:05[ 539.314266] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 02:46:05[ 539.314270] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 02:46:05[ 539.314275] [<ffffffff8107f266>] kthread+0x96/0xa0 02:46:05[ 539.314280] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 02:46:05[ 539.314284] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 02:46:05[ 539.314288] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 02:46:05[ 539.314291] ---[ end trace 76dbffc2d5d49d9b ]--- 02:46:05[ 539.314296] ata1: EH complete 02:46:12[ 547.040091] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen 02:46:12[ 547.040098] ata1.00: failed command: IDENTIFY DEVICE 02:46:12[ 547.040106] ata1.00: cmd ec/00:00:00:00:00/00:00:00:00:00/40 tag 0 pio 512 in 02:46:12[ 547.040108] res 40/00:01:00:00:00/00:00:00:00:00/e0 Emask 0x4 (timeout) 02:46:12[ 547.040111] ata1.00: status: { DRDY } 02:46:12[ 547.040117] ata1: hard resetting link 02:46:13[ 547.390144] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:13[ 547.408430] ata1.00: configured for UDMA/100 02:46:13[ 547.408438] ------------[ cut here ]------------ 02:46:13[ 547.408447] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 02:46:13[ 547.408451] Hardware name: MacBookPro5,3 02:46:13[ 547.408453] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 02:46:13[ 547.408528] Pid: 202, comm: scsi_eh_0 Tainted: P W 2.6.35-25-generic #44-Ubuntu 02:46:13[ 547.408531] Call Trace: 02:46:13[ 547.408540] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 02:46:13[ 547.408544] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 02:46:13[ 547.408549] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 02:46:13[ 547.408553] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 02:46:13[ 547.408563] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 02:46:13[ 547.408567] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 02:46:13[ 547.408572] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 02:46:13[ 547.408577] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 02:46:13[ 547.408582] [<ffffffff8107f266>] kthread+0x96/0xa0 02:46:13[ 547.408587] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 02:46:13[ 547.408591] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 02:46:13[ 547.408595] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 02:46:13[ 547.408598] ---[ end trace 76dbffc2d5d49d9c ]--- 02:46:13[ 547.408620] ata1: EH complete 02:46:13[ 547.562470] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:13[ 547.671380] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:13[ 547.738198] ata1.00: limiting speed to UDMA/33:PIO4 02:46:13[ 547.738204] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5800000 action 0xe frozen t4 02:46:13[ 547.738208] ata1: irq_stat 0x00000040, connection status changed 02:46:13[ 547.738212] ata1: SError: { LinkSeq TrStaTrns DevExch } 02:46:13[ 547.738218] ata1: hard resetting link 02:46:13[ 547.738262] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5900000 action 0xe frozen t4 02:46:13[ 547.738265] ata2: irq_stat 0x00000040, connection status changed 02:46:13[ 547.738269] ata2: SError: { Dispar LinkSeq TrStaTrns DevExch } 02:46:13[ 547.738274] ata2: hard resetting link 02:46:14[ 548.482561] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:14[ 548.484083] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:14[ 548.486809] ata2.00: configured for UDMA/100 02:46:14[ 548.486818] ata2: EH complete 02:46:14[ 548.498998] ata1.00: configured for UDMA/33 02:46:14[ 548.499004] ata1: EH complete 02:46:18[ 552.410499] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:18[ 552.522521] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:18[ 552.529674] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5800000 action 0xe frozen t4 02:46:18[ 552.529678] ata1: irq_stat 0x00000040, connection status changed 02:46:18[ 552.529680] ata1: SError: { LinkSeq TrStaTrns DevExch } 02:46:18[ 552.529684] ata1: hard resetting link 02:46:18[ 552.529716] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5800000 action 0xe frozen t4 02:46:18[ 552.529718] ata2: irq_stat 0x00000040, connection status changed 02:46:18[ 552.529720] ata2: SError: { LinkSeq TrStaTrns DevExch } 02:46:18[ 552.529723] ata2: hard resetting link 02:46:19[ 553.280059] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:19[ 553.280068] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:19[ 553.284141] ata2.00: configured for UDMA/100 02:46:19[ 553.284150] ata2: EH complete 02:46:19[ 553.301629] ata1.00: configured for UDMA/33 02:46:19[ 553.301637] ata1: EH complete

    Read the article

< Previous Page | 11 12 13 14 15 16 17 18 19 20 21 22  | Next Page >