Search Results

Search found 2824 results on 113 pages for 'supply chain'.

Page 15/113 | < Previous Page | 11 12 13 14 15 16 17 18 19 20 21 22  | Next Page >

  • Power cycles on/off 3 times before booting properly from cold start, no other issues (New System)

    - by James
    Relevant Specs: Sapphire 5850, core i7 920, Seasonic x750 power supply, ECS X58B-A2 mobo. From a cold boot, meaning all power totally disconnected at the wall, the system will power on for less than a second and then power off completely. After two seconds of being powered off this will repeat and on the third "attempt" the computer will boot. To be very specific here is what happens: The power is turned on at the wall and on the psu, the orange stdby LED on the mobo is illuminated but the system is 'off'. I hit the power button on the case or on the mobo itself I hear the relay (?) in the psu closing The case light comes on and the mobo power light comes on. The fans start rotating. Immediately after this the I hear some relay click - the power lights extinguish, the fans stop, the stdby light remains on. Less than 2 seconds pass and the cycle repeats without any intervention from me. On the third attempt it boots normally and the machine runs perfectly. If I do a soft reboot or a full shutdown the computer starts normally the next time. It's only if I pull the power cord or flick the switch off on the PSU that I get the cycling again. Basically any time the stdby light on the mobo goes out. I have removed the graphics card and I get the same problem. I have removed the PSU, hotwired it to the ON position and verified voltages on all lines. The relay does not cycle when I do this. If I connect only the 24 pin ATX connector to the mobo and not the 8 pin ATX12V / CPU connector then I will not get the cycling, the fans run, the power light stays on, but obviously the system can't boot. Disconnecting all fans has no effect on the problem. My feeling it that it's something to do with the motherboard like a capacitor that's taking a long time to charge because it's leaking or something along those lines. But I can't imagine what could be 'wrong' with it and only manifest itself as a problem under these very specific circumstances. Any ideas? Thanks.

    Read the article

  • USB ports causing Wireless and Mobile Phone tethering drop out

    - by chrolli
    I have a problem with my USB ports and I can't seem to pinpoint the problem. I'm hoping that I can get some idea as to how to troubleshoot my problem. Problem description: I recently bought a USB Wireless Adapter in order to connect my Desktop PC to the WLAN. The dongle keeps dropping off connection regularly on average once a minute. And the connection is slow. What I've tried: I installed a network scanner to determine signal strength. The PC/adapter combo is getting about 70% signal strength. I have a laptop that has an internal Wireless adapter. I moved the laptop near the location of the PC. The signal strength was above 90%. I installed the USB adapter on the laptop. I placed the laptop near the location of the PC. The signal strength was above 80%. And there is no drop out issue. I've isolated the problem to be on the PC. I used internet tethering on my mobile phone in order to test the USB ports. I get the same problem, themobile phone keeps dropping in and out. I plugged the adapter and phone on all USB ports, and it is still dropping out on all ports. I've isolated the problem to be the Motherboard, USB hub. I updated the BIOS, and USB driver. Still dropping out. I noticed that when I used the mobile phone tethering method, the phone (iphone 5) is guarenteed to drop out and does not appear to charge if I jiggle the the 8-pin connector on the base of the phone. If I push the pin tightly on the phone, the phone starts charging, as soon as I let go, it stops and drops out from the PC. This is strange because this doesn't happen when it is plugged to the powerboard. Which means that the 8 pin connector is fine. I'm not sure what the problem is. I assume that it is to do with the USB ports not supplying enough power which in turn causes the devices to intermittently drop out. The reason I say this is because the USB cable works fine when plugged into a powerboard with enough power supplied to the phone. Only when it is plugged into the USB port on the PC, does it drop out. My motherboard is Asus P8z68-v le. My Wireless adapter is the D-link DWA131. I can't seem to find any settings in the BIOS to increase the south bridge voltage so as to supply more power to the USB ports. Although this problem only occurs when I'm trying to hook up to a device supplying internet connection. My USB HDD, Flash drives, and Mouse and Key are working fine! Any suggestions please?

    Read the article

  • New harddrives failing within weeks.

    - by Jason Kealey
    I've experienced 8 hard disk failures in 3 months and have tried many things to solve the issue permanently but I have failed. I would like to know if you have any advice for me. System was running Win XP on an Asus P5W-DH Deluxe. I have setup a RAID-1 array. I started out with 2 x 500 GB 7200RPM Western Digital drives. One died. I took it out to RMA it. On the same day, the router was fried. Assumed a power surge occurred; connected an older UPS to protect the system. Once I got my hands on an identical disk, I installed it. The RAID array was rebuilt. A few days later, the other one died. Assumed the rebuild caused it to fail. Took it out for RMA. Before the other one arrived, the remaining one died. I then discovered I could re-enable them using the Intel Matrix Storage Manager. I re-enabled both and the system seemed fine for a week, until both died again. I got two new 1.5 TB 7200RPM Seagate drives and re-installed Windows 7. Also replaced the UPS and power supply. They both died again. The voltage on the plug is stable between 120 and 122V as per the UPS. None of the other devices have had any problems (monitors, etc.). At this point, I see two options: a) electrical issue in the house that was, for some reason, not blocked by the UPS. b) something else inside the system causing surges? motherboard? onboard raid controller? Failures happen fairly quickly, between 2 and 14 days after I fix the previous issue. I just gotten a new computer (Core i7) to replace it. If it is stable, I can determine that b) was the problem. If it fries its hard drive again, I can determine that it is an electrical issue in the house. Do you have any other thoughts? Any tools I can run on the drives that failed to get more information about the original SMART event history?

    Read the article

  • Computer makes hissing noise, turns off after few seconds

    - by Kaustubh P
    I have a problem similar to the questions posted here and here. This is my config: Asus M3N78-EM, with AMD Phenom X3 720 2800 Black Edition, 4GB Transcend DDR2 RAM, Nvidia 9400GT. HD is a 160 GB IDE, and a LG IDE DVD-ROM. The power button is a bit off, I have removed the cover of the switch, and the only way it turns on is just giving the "stick" under the cover a gentle press. It turns on sometimes, and at other times, I have to cut-off the power from the PSU, and try again. I will describe my problem in as detail as possible, please bear with me: The problem has started in the last week, a few months after I changed the to the powerswitch arrangement as described above. The PC makes a hissing noise, and I wasn't able to pin-point the noise source, because of the various other fans. At first, removing the HD, rebooting w/o the HD, turning it off, reconnecting and booting made the problem go away. But of late, it doesn't happen. As suggested in the other questions, I tried reducing the load by disconnecting both the IDE drives, and the problem (noise + turn-off) still occurs. I also connected another 80G IDE HD,today morning, adn it still made that noise, and turned off. I also opened up the PSU, but I couldn't see any fault in that, I tried rotating the fan by blowing into the blades, and with my fingers, but the hissing noise didn't come from there. Or maybe the speed wasn't enough to evoke that noise. A few weeks ago: I had cleaned the Cabinet and had repasted the processor and its fan using some thermal paste. Could that be at fault? I also used a vacuum to blow the dust out of the PSU, could the power have been too much, to maybe offset the fan or something? A label on the PSU says it uses a ball-bearing fan. That only leaves me with the Processor fan and the processor itself. I didn't try removing the processor fan and processor from the motherboard, and then turning the PC on, fearing damage. Will doing so cause any damage? What can I do to localize and pin-point the problem? Also, after a few tries, the Computer starts up. Sometimes it turns of within 2 seconds, sometimes after the POST. Once it turned off at the grub. Another time it booted completely and then turned off. The only way to ensure that the PC wont turn off, is if the hissing noise stops. EDIT: I suspect it to be the Processor/Processor fan, owing to the source of noise. All the config, except for the Cabinet, is just over a year old. EDIT2: I also just remembered, that I had set the "On-power resume" to turn on, i.e. If I supply he PC with power, it will turn itself on, w/o me needing to press the switch. I had done that to workaround the faulty power-switch, as noted above. EDIT3: I calculated the power my system needs, from the antec site, and I just arrived at 292W

    Read the article

  • How can I disable DNSSC for Google Apps (GMail) MX records on my authoritative domains?

    - by meinemitternacht
    I'm running a BIND Master / Slave setup with DNSSEC, but some of my domains use Google Apps for e-mail services. Google doesn't support DNSSEC and BIND doesn't like it at all. Log output: Sep 6 17:12:51 srv549 named[5376]: error (broken trust chain) resolving 'ALT2.ASPMX.L.GOOGLE.COM.dlv.isc.org/DLV/IN': 70.32.45.42#53 Sep 6 17:12:51 srv549 named[5376]: error (broken trust chain) resolving 'ALT2.ASPMX.L.GOOGLE.COM/A/IN': 70.32.45.42#53 Sep 6 17:12:51 srv549 named[5376]: error (broken trust chain) resolving 'ALT2.ASPMX.L.GOOGLE.COM/AAAA/IN': 70.32.45.42#53 Sep 6 17:12:51 srv549 named[5376]: validating @0x7f755cb83950: ALT2.ASPMX.L.GOOGLE.COM AAAA: bad cache hit (ALT2.ASPMX.L.GOOGLE.COM.dlv.isc.org/DLV) Sep 6 17:12:51 srv549 named[5376]: error (broken trust chain) resolving 'ALT2.ASPMX.L.GOOGLE.COM/AAAA/IN': 69.147.224.178#53 Sep 6 17:12:51 srv549 named[5376]: validating @0x7f755ca52c30: ALT2.ASPMX.L.GOOGLE.COM A: bad cache hit (ALT2.ASPMX.L.GOOGLE.COM.dlv.isc.org/DLV) Sep 6 17:12:51 srv549 named[5376]: error (broken trust chain) resolving 'ALT2.ASPMX.L.GOOGLE.COM/A/IN': 69.147.224.178#53 Sep 6 17:12:51 srv549 named[5376]: validating @0x7f755ca52c30: ASPMX2.GOOGLEMAIL.COM AAAA: bad cache hit (ASPMX2.GOOGLEMAIL.COM.dlv.isc.org/DLV) Sep 6 17:12:51 srv549 named[5376]: error (broken trust chain) resolving 'ASPMX2.GOOGLEMAIL.COM/AAAA/IN': 70.32.45.42#53 Sep 6 17:12:51 srv549 named[5376]: validating @0x7f755cb83950: ASPMX2.GOOGLEMAIL.COM A: bad cache hit (ASPMX2.GOOGLEMAIL.COM.dlv.isc.org/DLV) Sep 6 17:12:51 srv549 named[5376]: error (broken trust chain) resolving 'ASPMX2.GOOGLEMAIL.COM/A/IN': 70.32.45.42#53 Sep 6 17:12:51 srv549 named[5376]: validating @0x7f754c1b0bd0: ASPMX2.GOOGLEMAIL.COM A: bad cache hit (ASPMX2.GOOGLEMAIL.COM.dlv.isc.org/DLV) Sep 6 17:12:51 srv549 named[5376]: error (broken trust chain) resolving 'ASPMX2.GOOGLEMAIL.COM/A/IN': 70.32.45.42#53 Sep 6 17:12:51 srv549 named[5376]: validating @0x7f754c1a6a30: ASPMX2.GOOGLEMAIL.COM AAAA: bad cache hit (ASPMX2.GOOGLEMAIL.COM.dlv.isc.org/DLV) Sep 6 17:12:51 srv549 named[5376]: error (broken trust chain) resolving 'ASPMX2.GOOGLEMAIL.COM/AAAA/IN': 70.32.45.42#53 Sep 6 17:12:51 srv549 named[5376]: validating @0x7f755cb83950: ASPMX3.GOOGLEMAIL.COM AAAA: bad cache hit (ASPMX3.GOOGLEMAIL.COM.dlv.isc.org/DLV) I'm not absolutely sure this is stopping Google Apps from working, because I just enabled all of the DNSSEC features. Does anyone here have experience with this?

    Read the article

  • USB drive errors after airport scan

    - by bobobobo
    Well, I just got a new PNY usb drive and it passed through an airport scanner yesterday. For some reason, I wrote to it and then tried to read from it today, and it gave me a corrupted error! chkdsk reports errors like: Bad links in lost chain at cluster 1179 corrected. Lost chain cross-linked at cluster 1200. Orphan truncated. Lost chain cross-linked at cluster 1228. Orphan truncated. Lost chain cross-linked at cluster 1236. Orphan truncated. Lost chain cross-linked at cluster 1237. Orphan truncated. Lost chain cross-linked at cluster 1244. Orphan truncated. Lost chain cross-linked at cluster 1250. Orphan truncated. Lost chain cross-linked at cluster 1266. Orphan truncated. Lost chain cross-linked at cluster 1278. Orphan truncated. etc. What is this from? Could it possibly be from the airport scanner, or is it likely a defective USB chip? How can I check the chip to see if I should just return/throw it away or continue to use it?

    Read the article

  • Motherboard/PSU crippling USB and Sata

    - by celebdor
    I very recently bought a new desktop computer. The motherboard is: Z77MX-D3H and the power supply is ocz zs series 550w. The issue I have is that once I boot to the operating system (I have tried with fedora and Ubuntu with kernels 2.6.38 - 3.4.0), my hard drive (2.5" Magnetic) occasionally makes a power switch noise and it resets. Needless to say, when this drive is the OS drive, the OS crashes. I also have a SSD that works fine with the same OS configurations, but if I have the magnetic hard drive attached as second drive, it works erratically and the reconnects result in corrupted data. I also noticed that whenever I plug an external hard drive USB2.0 or USB3.0 to the computer the issue with the reconnects is even worse: [ 52.198441] sd 7:0:0:0: [sdc] Spinning up disk... [ 57.955811] usb 4-3: USB disconnect, device number 3 [ 58.023687] .ready [ 58.023914] sd 7:0:0:0: [sdc] READ CAPACITY(16) failed [ 58.023919] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.023932] sd 7:0:0:0: [sdc] Sense not available. [ 58.024061] sd 7:0:0:0: [sdc] READ CAPACITY failed [ 58.024063] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.024064] sd 7:0:0:0: [sdc] Sense not available. [ 58.024099] sd 7:0:0:0: [sdc] Write Protect is off [ 58.024101] sd 7:0:0:0: [sdc] Mode Sense: 00 00 00 00 [ 58.024135] sd 7:0:0:0: [sdc] Asking for cache data failed [ 58.024137] sd 7:0:0:0: [sdc] Assuming drive cache: write through [ 58.024400] sd 7:0:0:0: [sdc] READ CAPACITY(16) failed [ 58.024402] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.024405] sd 7:0:0:0: [sdc] Sense not available. [ 58.024448] sd 7:0:0:0: [sdc] READ CAPACITY failed [ 58.024450] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.024451] sd 7:0:0:0: [sdc] Sense not available. [ 58.024469] sd 7:0:0:0: [sdc] Asking for cache data failed [ 58.024471] sd 7:0:0:0: [sdc] Assuming drive cache: write through [ 58.024472] sd 7:0:0:0: [sdc] Attached SCSI disk [ 58.407725] usb 4-3: new SuperSpeed USB device number 4 using xhci_hcd [ 58.424921] scsi8 : usb-storage 4-3:1.0 [ 59.424185] scsi 8:0:0:0: Direct-Access WD My Passport 0740 1003 PQ: 0 ANSI: 6 [ 59.424406] scsi 8:0:0:1: Enclosure WD SES Device 1003 PQ: 0 ANSI: 6 [ 59.425098] sd 8:0:0:0: Attached scsi generic sg2 type 0 [ 59.425176] ses 8:0:0:1: Attached Enclosure device [ 59.425248] ses 8:0:0:1: Attached scsi generic sg3 type 13 [ 61.845836] sd 8:0:0:0: [sdc] 976707584 512-byte logical blocks: (500 GB/465 GiB) [ 61.845838] sd 8:0:0:0: [sdc] 4096-byte physical blocks [ 61.846336] sd 8:0:0:0: [sdc] Write Protect is off [ 61.846338] sd 8:0:0:0: [sdc] Mode Sense: 47 00 10 08 [ 61.846718] sd 8:0:0:0: [sdc] No Caching mode page present [ 61.846720] sd 8:0:0:0: [sdc] Assuming drive cache: write through [ 61.848105] sd 8:0:0:0: [sdc] No Caching mode page present [ 61.848106] sd 8:0:0:0: [sdc] Assuming drive cache: write through [ 61.857147] sdc: sdc1 [ 61.858915] sd 8:0:0:0: [sdc] No Caching mode page present [ 61.858916] sd 8:0:0:0: [sdc] Assuming drive cache: write through [ 61.858918] sd 8:0:0:0: [sdc] Attached SCSI disk [ 69.875809] usb 4-3: USB disconnect, device number 4 [ 70.275816] usb 4-3: new SuperSpeed USB device number 5 using xhci_hcd [ 70.293063] scsi9 : usb-storage 4-3:1.0 [ 71.292257] scsi 9:0:0:0: Direct-Access WD My Passport 0740 1003 PQ: 0 ANSI: 6 [ 71.292505] scsi 9:0:0:1: Enclosure WD SES Device 1003 PQ: 0 ANSI: 6 [ 71.293527] sd 9:0:0:0: Attached scsi generic sg2 type 0 [ 71.293668] ses 9:0:0:1: Attached Enclosure device [ 71.293758] ses 9:0:0:1: Attached scsi generic sg3 type 13 [ 73.323804] usb 4-3: USB disconnect, device number 5 [ 101.868078] ses 9:0:0:1: Device offlined - not ready after error recovery [ 101.868124] ses 9:0:0:1: Failed to get diagnostic page 0x50000 [ 101.868131] ses 9:0:0:1: Failed to bind enclosure -19 [ 101.868288] sd 9:0:0:0: [sdc] READ CAPACITY(16) failed [ 101.868292] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868296] sd 9:0:0:0: [sdc] Sense not available. [ 101.868428] sd 9:0:0:0: [sdc] READ CAPACITY failed [ 101.868434] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868439] sd 9:0:0:0: [sdc] Sense not available. [ 101.868468] sd 9:0:0:0: [sdc] Write Protect is off [ 101.868473] sd 9:0:0:0: [sdc] Mode Sense: 00 00 00 00 [ 101.868580] sd 9:0:0:0: [sdc] Asking for cache data failed [ 101.868584] sd 9:0:0:0: [sdc] Assuming drive cache: write through [ 101.868845] sd 9:0:0:0: [sdc] READ CAPACITY(16) failed [ 101.868849] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868854] sd 9:0:0:0: [sdc] Sense not available. [ 101.868894] sd 9:0:0:0: [sdc] READ CAPACITY failed [ 101.868898] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868903] sd 9:0:0:0: [sdc] Sense not available. [ 101.868961] sd 9:0:0:0: [sdc] Asking for cache data failed [ 101.868966] sd 9:0:0:0: [sdc] Assuming drive cache: write through [ 101.868969] sd 9:0:0:0: [sdc] Attached SCSI disk Now, if I plug the same drive to the powered usb 2.0 hub of my monitor, the issue is not reproduced (at least on a 20h long operation). Also the issue of the usb reconnects is less frequent if the hard drive is plugged before I switch on the computer. Does anybody have some advice as to what I could do? Which is the faulty part/s that I should replace? As for me, I really don't know if to point my finger to the PSU or the Motherboard (I have updated to the latest firmware and checked the BIOS settings several times). EDIT: The reconnects are happening both in the Sata connected drives and the USBX connected drives.

    Read the article

  • Lazy Sequences that "Look Ahead" for Project Euler Problem 14

    - by ivar
    I'm trying to solve Project Euler Problem 14 in a lazy way. Unfortunately, I may be trying to do the impossible: create a lazy sequence that is both lazy, yet also somehow 'looks ahead' for values it hasn't computed yet. The non-lazy version I wrote to test correctness was: (defn chain-length [num] (loop [len 1 n num] (cond (= n 1) len (odd? n) (recur (inc len) (+ 1 (* 3 n))) true (recur (inc len) (/ n 2))))) Which works, but is really slow. Of course I could memoize that: (def memoized-chain (memoize (fn [n] (cond (= n 1) 1 (odd? n) (+ 1 (memoized-chain (+ 1 (* 3 n)))) true (+ 1 (memoized-chain (/ n 2))))))) However, what I really wanted to do was scratch my itch for understanding the limits of lazy sequences, and write a function like this: (def lazy-chain (letfn [(chain [n] (lazy-seq (cons (if (odd? n) (+ 1 (nth lazy-chain (dec (+ 1 (* 3 n))))) (+ 1 (nth lazy-chain (dec (/ n 2))))) (chain (+ n 1)))))] (chain 1))) Pulling elements from this will cause a stack overflow for n2, which is understandable if you think about why it needs to look 'into the future' at n=3 to know the value of the tenth element in the lazy list because (+ 1 (* 3 n)) = 10. Since lazy lists have much less overhead than memoization, I would like to know if this kind of thing is possible somehow via even more delayed evaluation or queuing?

    Read the article

  • Amazon EC2 Socket connection not being accepted

    - by Joseph
    I am trying to run a java application on my EC2 instance. The application accepts socket connections on port 54321. If I try and connect to it, it times out. My Security Group is set as: TCP Port (Service) Source Action 21 0.0.0.0/0 Delete 22 (SSH) 0.0.0.0/0 Delete 80 (HTTP) 0.0.0.0/0 Delete 20393 0.0.0.0/0 Delete 54321 0.0.0.0/0 Delete Is there anything else I need to do? # iptables -nvL Chain INPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination # iptables -nvL -t nat Chain PREROUTING (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain INPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain POSTROUTING (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination #

    Read the article

  • Why is my RapidSSL Certificate chain is not trusted on ubuntu?

    - by olouv
    I have a website that works perfectly with Chrome & other browser but i get some errors with PHP in CLI mode so i'm investigating it, running this: openssl s_client -showcerts -verify 32 -connect dev.carlipa-online.com:443 Quite suprisingly my HTTPS appears untrusted with a Verify return code: 27 (certificate not trusted) Here is the raw output : verify depth is 32 CONNECTED(00000003) depth=2 C = US, O = GeoTrust Inc., CN = GeoTrust Global CA verify error:num=20:unable to get local issuer certificate verify return:1 depth=2 C = US, O = GeoTrust Inc., CN = GeoTrust Global CA verify error:num=27:certificate not trusted verify return:1 depth=1 C = US, O = "GeoTrust, Inc.", CN = RapidSSL CA verify return:1 depth=0 serialNumber = khKDXfnS0WtB8DgV0CAdsmWrXl-Ia9wZ, C = FR, O = *.carlipa-online.com, OU = GT44535187, OU = See www.rapidssl.com/resources/cps (c)12, OU = Domain Control Validated - RapidSSL(R), CN = *.carlipa-online.com verify return:1 So GeoTrust Global CA appears to be not trusted on the system (Ubuntu 11.10). Added Equifax_Secure_CA to try to solve this... But i get in this case Verify return code: 19 (self signed certificate in certificate chain) ! Raw output : verify depth is 32 CONNECTED(00000003) depth=3 C = US, O = Equifax, OU = Equifax Secure Certificate Authority verify error:num=19:self signed certificate in certificate chain verify return:1 depth=3 C = US, O = Equifax, OU = Equifax Secure Certificate Authority verify return:1 depth=2 C = US, O = GeoTrust Inc., CN = GeoTrust Global CA verify return:1 depth=1 C = US, O = "GeoTrust, Inc.", CN = RapidSSL CA verify return:1 depth=0 serialNumber = khKDXfnS0WtB8DgV0CAdsmWrXl-Ia9wZ, C = FR, O = *.carlipa-online.com, OU = GT44535187, OU = See www.rapidssl.com/resources/cps (c)12, OU = Domain Control Validated - RapidSSL(R), CN = *.carlipa-online.com verify return:1 Edit Looks like my server does not trust/provide the Equifax Root CA, however i do correctly have the file in /usr/share/ca-certificates/mozilla/Equifax...

    Read the article

  • JAX-WS modifying handler chain programmatically? PortInfo?

    - by wuntee
    I have a JAX-WS client that needs to have a modified handler-chain. I am currently doing it by binding this XML when generated the WSDL stubs: <jaxws:bindings xmlns:jaxws="http://java.sun.com/xml/ns/jaxws"> <jws:handler-chains xmlns:jws="http://java.sun.com/xml/ns/javaee"> <jws:handler-chain> <jws:handler> <jws:handler-name>ServiceRequestServiceClientHandler</jws:handler-name> <jws:handler-class>blah.ServiceRequestServiceClientHandler</jws:handler-class> </jws:handler> </jws:handler-chain> </jws:handler-chains> </jaxws:bindings> I was looking that the ServiceRequestService_Service object, and it seems like this could be done programmatically (easier in my opinion - less configuration files). new ServiceRequestService_Service().getHandlerResolver().getHandlerChain(PORTINFO).add(HANDLER); But, I do not know what the PortInfo object is, or how to obtain it in relation to the specific service. Has anyone done this?

    Read the article

  • alias_attribute and creating and method with the original attribute name causes a loop

    - by Tiago
    Im trying to dynamically create a method chain in one attribute in my model. By now I have this function: def create_filtered_attribute(attribute_name) alias_attribute "#{attribute_name}_without_filter", attribute_name define_method "#{attribute_name}" do filter_words(self.send("#{attribute_name}_without_filter")) end end so I receive a string with the attribute name, alias it for '*_without_filter*' (alias_method or alias_method_chain fails here, because the attribute isnt there when the class is created), and I create a new method with the attribute name, where I filter its contents. But somehow, when I call *"#{attribute_name}_without_filter"* it calls my new method (i think because the alias_attribute some how), and the program goes into a stack loop. Can someone please enlighten me on this.

    Read the article

  • LCD monitor flickering

    - by stickmangumby
    I've recently got an LCD monitor and it is occasionally 'flickering' colors very noticeably. It's not a new monitor, but the person I'm borrowing it from hasn't had any trouble with it. The flickering occurs across operating systems and screen resolutions. I'm pretty sure it's related to dirty power - it often happens when fluorescent lights get turned on or the fridge starts, but not always. Is this likely to be the cause of the problem? Is there any good way to test this? Is there anything that can be done about bad grounding?

    Read the article

  • Dell PSU Compatibility: Dell Inspiron 530 (Desktop)

    - by ashes999
    I have an Inspiron 530 with a stock PSU. I need to upgrade it to meet my video card's needs (AMD HD6770), which demands at least 450W, to potentially fix BSODs with the latest version of the drivers (so claims AMD support). Now, I've heard conflicting reports about whether Dell uses special/proprietary PSUs. (Examples for aye and nay to special PSUs.) How exactly can I determine if a PSU is compatible with my PC, before buying it? I assume I will not be able to return it if it doesn't fit, or makes my computer explode in a fireball of doom.

    Read the article

  • What are good values for PSU voltages?

    - by earlz
    Hello, I have an odd computer I'm trying to fix that will crash only during the setup of an OS(crashes on every OS I've tried so far) It's not overheating and it is stripped down as much as possible and I've tried multiple harddrives, and memtest86+ can run on it for 3 hours without a crash or fail. So, I was a bit stumped and was looking in the BIOS for possible causes and found a hardware monitor that shows PSU voltages. They are: VCORE: 1.432V 3.3V: 3.136V 5V: 5.273 12V: 12.144V I thought the 3.3V looked a little low, but I'm not really sure on how "bad" that is. So, what are the good ranges for the voltages on each CPU rail?

    Read the article

  • How to recover a file using the FAT cluster chain instead of using the stored length in the FAT table?

    - by cadrian
    I'm trying to recover movie files from my TNT receiver hard drive but it corrupts its FAT32 allocation table (crappy cheap device...) Using dosfsck is useless because the correct file length is the cluster length, not the (shorter) one in the table, and dosfsck only proposes to shorten the file, which I won't do. Question: how to recover a file using the FAT cluster chain instead of using the stored length in the FAT table? Edit I forgot to say: Linux solutions only please (I have no windows box)

    Read the article

  • Computer does not switch on after power outage

    - by cristian
    VOLTAGE DROP OFF FOR PC does not restart The other day my pc was turned off due to power outage. Since that time the computer would not turn on again, no sign of life, it seems dead. I did several tests, changed the power outlet and disconnect the wires ... also I have reseated the cards ... but the result is that nothing changes. What can I do? Could there may be damage to the hardware due to the power outage? Note: the voltage drop is not due to a lightning storm and so is not due to damaged components (burnt card etc ...) Original Text: l'altro giorno il pc mi si è spento improvvisamente per calo tensione.... da quel momento non si è piu' riacceso...nessun segnale di vita...sembra proprio morto. Ho fatto diverse prove, cambio presa di alimentazione, scollegare i fili...insomma ho "mischiato le carte"...ma il risultato è che non cambia nulla. Cosa posso fare? cosa puo' essere successo? Possono esserci danni hardware per il calo di tensione? NB: il calo di tensione non e' dovuto ad una saetta e quindi escluderei danni causa temporale (bruciature scheda ecc...) Grazie mille

    Read the article

  • SMPS stops when I plug in a SATA drive?

    - by claws
    Hello, Part 1: my first question is all the 4 wire power connectors (intended for hardisks/dvd drives not mother board) are same. Right? I've been using all of them same and I had no problem for years. Yesterday I borrowed a SATA disk from my friend and connected it my computer using Sata Power adaptor (4 wire) and when I switched on the computer. There were fumes coming out of the connector. I immediately turned it off (in just one second). I tested the voltages in the 4 wire power connector of my SMPS: They were 5.3v & 12.2V. I couldn't measure the current. But my SMPTS label reads: DC Output: 3.3v (25A) +5v (32A) -5v (0.3A) +12V (17A) -12V (0.8A) And the SATA hardisk label reads Input: +5v (0.72A) +12V (0.52A) I'm shocked! I never noticed this. Does the "sata power adaptor" scale down the current to required? If it doesn't, I've been connecting same way for years. I never had any problem. This is the first time I'm encountering it. Part 2: I wanted to return the drive to my friend. He has two hard disks, SATA & PATA. Its the SATA that I borrowed. When he usually switches on. The CPU fan starts & then stops for a sec and starts again and continues working. That was the earlier situation. I don't know why it stops & starts? Well, Now when I connect this SATA disk and switch ON the computer. CPU fan starts (just for an instant, not even a 0.5 sec) and stops. It doesn't start again, I mean the power from SMPS has stopped. But if I disconnect this SATA disk. It works fine. What seems to be the problem? I've no idea about why there were fumes or why his SMPS starts & stops giving power? What is its relation with the SATA disk connection?

    Read the article

  • Computer loses all installed programs and appears to return OS-only state

    - by Jake
    This is a story regarding 3 laptops of different brand and models. On separate occassions, I configured each of these Windows 7 / Vista computers with the necessary configuration and applications (which are supposedly the same actually), e.g. join office domain, same windows updates, microft office etc. These machinese were configure in our office in Singapore, and then they were taken to India for use. Someday in India, when booting up the laptop, all went fine except when it reach the log in screen, it was no longer possible to login with domain credentials. Logging into the laptop local admin account will lead to discover that the machine has returned to "OS-only state". All the configurations and applications were gone. The actual user profiles are still in the C: drive so files can still be retrieved, but under Control Panel Uninstall Programs it is evident that at least the registry is corrupted. The above scenario happen to the first 2 laptops. For the third, the system reports "Operating System Not Found" on boot up. I cannot think of any reason except to suspect a power fluctuation issue. Question is, will a power issue create this behaviour? What else can cause this issue?

    Read the article

  • PSU requirement question for my PC setup.

    - by user69474
    I understand that sometimes there may be a situation where the PSU is way more than required but in this case of mine, I'm not too sure. Sometimes when I play games, my computer will crash and restarts itself, 10 mins into the game. Once I received a message that says something like the power is overheating or something like that. Ok, so I have a 500W PSU. I have: 1x Internal DVD writer 1x SATA 250GB HD 1x Nvidia 8500 GT 2GB RAM. As I'm planning to get an additional 250GB SATA HD, I wonder if I need to increase my PSU as well -- in full knowledge of the previous crashes experienced before. Should I upgrade my PSU to 650W perhaps, or is that excessive?

    Read the article

  • What is the best position for power unit?

    - by guest86
    I would like to buy new computer case. Last time I bought a computer was in 2008 and many things have changed up to day. Many new computer cases have power unit placed down, on bottom. I'm thinking about buying some of those cases, but i'm not sure about something - if power unit is placed on the bottom it can't take away hot air from the case and pump it out right? All my PC parts are silent - CPU (E8200, placed below 12cm Nochtua fan of power unit) has heat-pipe cooler with Nochtua fan spinning at only 800rpms, GPU has cooler powered by 7V instead 12 and that's why i don't want to HAVE TO place another fan to pump out hot air instead of PU placed on top. That might make some noise. So i ask someone more experienced: if i buy some computer case with PU placed down, do i HAVE TO place some fan to pump out hot air?

    Read the article

  • Windows 7 remains powered on when restarting

    - by BombDefused
    I'm running windows 7 x64 on an MSI P67A-GD53 motherboard, in an Antec P280 Super Midi Towercase with a Corsair 650w PSU. I've just installed a second instance of windows 7 x64 on a separate disk (this is to keep my games separate from my work OS). The problem is that it appears now that I cannot restart from either instance of Windows 7. The shut down command, and sleep commands work as expected. When I try to restart, the shutdown happens but the system never reboots. Everything remains powered on, until I hold down the power button to force the power off. Ithink (but am not 100% sure) this has only started since I installed the second OS, and am assuming this has something to do with the motherboard needing to know which OS to run up again? Some other forums I've read suggest that the PSU has a major role in restart and could be at fault. Changing the boot order of the disks in the BIOS does not change anything. Any suggestions greatfully recieved! Update: I now have a reproduceable issue: I think the secondary OS install may have been a red herring. It was when windows tried to reboot during the install that I noticed the issue. After playing around with installing drivers, and rebooting many many times, I have found that it is the OC genie setting on the MSI motherboard that seems to trigger the problem. This makes sense as I only started using the OC genie feature a couple of weeks ago, and probably hadn't used restart in that time. However... simply turning off OC genie does not make the issue go away. I have to turn off OC genie, shutdown, start enter bios, go to the "Save and Exit" menu "Restore Defaults" yes to "Load optimized defaults", which will reset to clear the problem. Now when the PC boots into windows, I can restart as normal (and from the OS on either HDD). I only know how to control the issue, and don't still know the root cause. I'd like to be able to use the OC genie function if anyone can suggest a why I'm seeing this problem. Could it be that I'm drawing too much power when using OC feature?

    Read the article

  • PSU Suggestions for SLI EVGA GTX 680 + i7

    - by JMH
    So i am putting together a new machine and am trying to determine the best PSU to go with for this setup. Here is the build i am thinking about Processor Intel Core i7-3770K Ivy Bridge 3.5GHz Motherboard ASRock Z77 Professional Graphics Card (2 SLI) EVGA 02G-P4-2680-KR Sound Card HT | OMEGA eClaro 7.1 Fan/Heat Sync ZALMAN CNPS9500A-LED Case COOLER MASTER HAF X RC-942-KKN1 RAM G.SKILL Ripjaws X Series 32GB (4 x 8GB) SSD Of some Sort So my guess is that i need a 750 -1000W PSU, but which brand.... how much, etc --- really in the woods. Thanks -Josh

    Read the article

< Previous Page | 11 12 13 14 15 16 17 18 19 20 21 22  | Next Page >