Search Results

Search found 4224 results on 169 pages for 'dual gpu'.

Page 150/169 | < Previous Page | 146 147 148 149 150 151 152 153 154 155 156 157  | Next Page >

• How to best tune my SAN/Initiators for best performance?

  - by Disco

  Recent owner of a Dell PowerVault MD3600i i'm experiencing some weird results. I have a dedicated 24x 10GbE Switch (PowerConnect 8024), setup to jumbo frames 9K. The MD3600 has 2 RAID controllers, each has 2x 10GbE ethernet nics. There's nothing else on the switch; one VLAN for SAN traffic. Here's my multipath.conf defaults { udev_dir /dev polling_interval 5 selector "round-robin 0" path_grouping_policy multibus getuid_callout "/sbin/scsi_id -g -u -s /block/%n" prio_callout none path_checker readsector0 rr_min_io 100 max_fds 8192 rr_weight priorities failback immediate no_path_retry fail user_friendly_names yes # prio rdac } blacklist { device { vendor "*" product "Universal Xport" } # devnode "^sd[a-z]" } devices { device { vendor "DELL" product "MD36xxi" path_grouping_policy group_by_prio prio rdac # polling_interval 5 path_checker rdac path_selector "round-robin 0" hardware_handler "1 rdac" failback immediate features "2 pg_init_retries 50" no_path_retry 30 rr_min_io 100 prio_callout "/sbin/mpath_prio_rdac /dev/%n" } } And iscsid.conf : node.startup = automatic node.session.timeo.replacement_timeout = 15 node.conn[0].timeo.login_timeout = 15 node.conn[0].timeo.logout_timeout = 15 node.conn[0].timeo.noop_out_interval = 5 node.conn[0].timeo.noop_out_timeout = 10 node.session.iscsi.InitialR2T = No node.session.iscsi.ImmediateData = Yes node.session.iscsi.FirstBurstLength = 262144 node.session.iscsi.MaxBurstLength = 16776192 node.conn[0].iscsi.MaxRecvDataSegmentLength = 262144 After my tests; i can barely come to 200 Mb/s read/write. Should I expect more than that ? Providing it has dual 10 GbE my thoughts where to come around the 400 Mb/s. Any ideas ? Guidelines ? Troubleshooting tips ?

  Read the article

• Get Illegal Instruction error when booting Linux in VirtualBox, works fine when booted directly

  - by rkjnsn

  I have a computer on which I am dual booting Windows 7 and Gentoo Linux (both 64-bit). I want to be able to load up my Linux installation in a VM while I am booted into Windows. I have installed VirtualBox and followed the instructions for creating a raw disk VMDK. When I start the VM, Linux starts booting, but then fails with the following error when unlocking my root partition: truecrypt[441] trap invalid opcode ip:373615538e0 sp:3dd0e0dfb60 error:0 in libpixman-1.so.0[373614d6000+8d000] Everything works fine when I boot into Linux directly. What could cause an illegal instruction to be hit in libpixman only when booting in VirtualBox? Update: As a troubleshooting step, I recompiled pixman without "-march", and no longer get an illegal instruction error in that library. (The boot fails in the same spot with the same error in a different library, however.) How can I determine the specific opcode that isn't working in VirtualBox so I can disable it in my CFLAGS without having to disable all CPU-specific optimizations? I am still confused as to why there would be any user-mode instruction that would fail to work in a VM. Is this a known limitation? My CPU is an Intel Core i7 3720QM, and I have hardware virtualization support enabled.

  Read the article

• Computer does not boot after ram upgrade

  - by Calmarius

  I have a Dell Optiplex GX520 desktop (it's abount 5 yr old) PC with 512 MB DDR2 RAM. Since my computer always swapping I thought I should upgrade my RAM. I bought a Kingmax 2GB DDR2 RAM. But my system does not boot. The status leds are on 2 and 4. The user manual says 'video card failure' wtf? I put back the original module and everything works. I tried many combinations. When I leave the old 512 RAM in and put the 2GB next to it to the other socket my system completes the POST and I'm able to enter the BIOS menu. It says my system has 2.5 GB installed, one 0.5GB and one 2GB in dual asymmetric channel mode. It's seemingly right. Exiting the BIOS setup GRUB loads successfully, but when I try to boot Ubuntu it crashes with kernel panic immediately. Trying to load Windows XP does not get past the loading screen, it crashes with 0x8E stop error. Does this mean the ram I bought is faulty? Or is it just mean that the memory module I bought is too new to be handled my computer? I this case I may exchange the RAM with my friends. No other computer is in my house (my very old box has DDR1 ram, my systers new box has DDR3 ones. I can't plug my memory in neither one.) I'm going to return the RAM to store to replace it with a better one tomorrow. Is there any hope to get this new module work?

  Read the article

• How can I control which sound card Ubuntu uses for playback?

  - by GorillaSandwich

  I am dual-booting Ubuntu 9.04 and Windows XP but am new to Ubuntu. In Windows, I use an M-Audio Audiophile 2496 sound card for recording (because it has RCA input jacks for my mixer), but I don't use it for playback (because my speakers use a 1/8 inch jack); instead, I use the motherboard's built-in sound card. I tried to recreate this arrangement in Ubuntu, but despite selecting the built-in card for all playback under System > Preferences > Sound, I still have inconsistent results. Rhythmbox plays back through the integrated card, but Flash content in the browser and games in the OS send their audio to the Audiophile card. I have seen recommendations to use a program called "Jack" to control this, but I installed it and found it baffling. How can I control which card is used for playback, other than disabling one card (as I discovered how to do and explain below)? Also, is there a GUI for disabling hardware, or is it necessary to edit a configuration file?

  Read the article

• How do I install a different OS on a Compaq Presario cq56 with preinstalled SuSE 11?

  - by McCoy

  Thing is, I don't have a clue of Linux systems, I usually use WinXP. Bought a notebook with SuSE 11 on it, because I have my XP licence and thought I could install that if I found the chipset drivers for the hardware (which I'm not completely sure I have the right versions of). Then I thought I'd give it a shot with the SuSE, looked nice enough. But I can't get my external hd to work (tried force mount) and the banshee doesn't do anything like playing video. Since that is one of the two main purposes of this notebook, I need to get that to work. Tried downloading VLC player, but that only works with SuSE 11.1 upwards. So I downloaded a SuSE 11.3 and burned the iso. But surprise, no way the notebook would boot from cd. Same with the XP cd (considered setting up a dual boot). And no, I can't get to BIOS to reset to default, either. So I can basically do nothing else than going online with this thing and that's not enough for me (gamer in withdrawal, yikes!). I need at least to get to my firefox profile on the external hd and be able to watch video. Can somebody please help me? I think at this point I'd prefer to install XP and MAYBE the SuSE 11.3 after that. I'm not a native speaker, so please speak plainly, thanks. :) Edit: if this is impossible, could someone please help me with the external hd mount and video playback? Edit: Found out how to boot from cd by now. But still no XP, because I get bluescreen after bluescreen while setup is loading files. I guess it's the missing SATA drivers...

  Read the article

• New build won't boot: some fans turning, no beep or video

  - by Dave

  When my new system is powered up, the case fan and power supply fans turn fine. The CPU fan twitches, but never gets going. Although I've heard that with AMDs and Gigabyte motherboards that is not necessary a problem. Hard drive is spinning. However, there is absolutely no indication that anything else is happening. The motherboard, as far as I can tell, does not have an internal speaker, but I harvested one from another machine and plugged it in and still no beeps at all. The monitor screen stays black, on both the integrated VGA and DVI. This is a brand new build, and has never successfully booted. My parts are: AMD Athlon II X2 245 Regor 2.9GHz Socket AM3 65W Dual-Core Processor Model ADX245OCGQBOX - includes CPU cooler) GIGABYTE GA-MA785GPMT-UD2H AM3 AMD 785G HDMI Micro ATX AMD Motherboard - Retail G.SKILL Ripjaws Series 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10666) Desktop Memory Model F3-10666CL8D-4GBRM - Retail CORSAIR CMPSU-400CX 400W ATX12V V2.2 80 PLUS Certified Compatible with Core i7 Power Supply - Retail SAMSUNG Spinpoint F3 HD502HJ 500GB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive COOLER MASTER Elite 341 RC-341C-KKN1-GP Black Steel MicroATX Mid Tower Computer Case - Retail I also have a DVD burner, but it acts the same whether that is plugged in or not. I'm using the on board video. What I've tried so far: I've switched power supplies, with no difference. I've tried different monitors (of which all are working on other machines) with no difference. I have tried putting it one memory module at a time, with no difference. I have tried the absolute minimum I can think of (power supply into motherboard, power button ONLY plugged into front panel, CPU fan plugged in), with no difference. I appreciate any ideas anyone might have. Do I need to RMA the motherboard? This is my first build, so there might be something obvious. I was very careful in assembly with static; I'm confident nothing was zapped during assembly.

  Read the article

• Am I getting the right memory for my motherboard?

  - by Daniel Carvalho

  Hi technophiles; I have a Gigabyte GA-EP45-DS motherboard. Also, the memory that came with my computer was two Transcend aXe RAM 1066MHZ 1GB modules. The thing is, I noticed that my motherboard has "DDR2 1200" written on it. This concerns me, have I bought slower memory than my computer is supposed to have ideally? Now, I'm not super concerned at a granular level about the best optimal RAM with the best CAS latency etc... but I do hope at least that I've got the right speed. Now, as far as I know, there is no such thing as ram at 1200MHZ? Am I right? You see, because I'm thinking of getting more RAM now, before I can't find the same type or speed any-more and just want to make sure it's the right thing. Furthermore, if the memory is slower than what I should be getting for my motherboard, what RAM should I be getting, and will that new RAM play nice with my old RAM? If I get new RAM at a different speed, would it be better / more beneficial performance-wise to omit the old RAM because of how the whole DUAL channel RAM thing works? I'm not too clued up on this area. Thanks chiefs.

  Read the article

• Install VirtualBox on Ubuntu 12.04.1 (on [Samsung] Chromebook)

  - by iphonedev7

  I have dual booted Ubuntu Linux 12.04.1 LTS on my Samsung Series 5 ChromeBook, and am trying to run/install Oracle VirtualBox (from the generic .run file downloaded from their website). However, every time I try to run it (as root from the command line), it gives me the following error occurs: Please install the build and header files for your current Linux kernel. The current kernel version is 3.4.0 Problems were found which would prevent VirtualBox from installing. I have tried the version from the Software Center, as well as the command line installation, both of which gave me errors based on my linux-headers/linux-kernel/linux-[kernel]-image. Here's an error I keep getting (on the command line): First Installation: checking all kernels... It is likely that 3.4.0 belongs to a chroot's host Building only for 3.5.0-18-generic Building initial module for 3.5.0-18-generic ERROR (dkms apport): kernel package linux-headers-3.5.0-18-generic is not supported Error! Bad return status for module build on kernel: 3.5.0-18-generic (x86_64) Consult /var/lib/dkms/virtualbox/4.1.12/build/make.log for more information. Setting up virtualbox-qt (4.1.12-dfsg-2ubuntu0.2) ... Processing triggers for libc-bin ... ldconfig deferred processing now taking place ...And one of the more cryptic errors I get when trying to start any Virtual Machine: Result Code: NS_ERROR_FAILURE (0x80004005) Component: Machine Interface: IMachine {5eaa9319-62fc-4b0a-843c-0cb1940f8a91}

  Read the article

• Gaming on Cloud

  - by technomad

  Sometimes I wonder the pundits of cloud computing are way to consumed with the enterprise applications. With all the CAPEX / OPEX, ROI-talk taking the center stage, an opportunity to affect masses directly is getting overlooked. I am a self proclaimed die hard gamer. I come from the generation of gamers who started their journey in DOS games like Wolfenstein 3D and Allan Border Cricket (the latter is still a favorite pastime). In the late 90s, a revolution called accelerated graphics started in DirectX and OpenGL. Games got more advanced. Likes of Quake III and Unreal Tournament became the crown jewels of the industry. But with all these advancements, there started a race. A race of GFX giants ATI and NVIDIA to beat each other for better frame and image quality. Revisions to the graphics chipsets became frequent. Games became eye candies but at the cost of more GPU power / memory. Every eagerly awaited title started demanding more muscle power in graphics and PC hardware. Latest games and all the liquid smooth frame rates became the territory of the once with deep pockets who could spend lavishly on latest hardware. Enthusiasts like yours truly, who couldn’t afford this route, started exploring over-clocking, optimized hardware cooling... etc. to pursue the passion. Ever rising cost of hardware requirements lead to rampant piracy of PC games. Gamers were willing to spend on the latest titles, but the ones with tight budget prefer hardware upgrades against a legal copy of the game. It was also fueled by emergence of the P2P file sharing networks. Then came the era of Xbox and PS3s. It solved the major issue of hardware standardization and provided an alternative to ever increasing hardware costs. I have always admired these consoles, but being born and brought up in a keyboard/mouse environment, I still find it difficult to play first person shooters with a gamepad. I leave the topic of PC v/s Consol gaming for another day, but the bottom line is… PC gamers deserve an equally democratized solution. This is where I think Cloud Computing can come to rescue. It can minimize hardware requirements. Virtually end the software piracy and rationalize costs for gamers. Subscription based models like pay-as-you-play. In game rewards, like extended subscription credits for exceptional gamers (oh yes, I have beaten Xaero on nightmare in Quake III, time and again!) Easy deployment for patches and fixes. Better game AI. The list goes on and on… Fortunately, companies like OnLive are thinking in the same direction. Their gaming service is all set to launch on 17th June 2010 in E3 2010 expo in L.A. I wish them all the luck. I hope they will start a trend which will bring the smiles back on the face of budget gamers with the help of cloud computing.

  Read the article

• WWNs,WWPNs and Fibre Channel addresses

  - by user238230

  Lots of contradictory on these subjects and I don't know why. My first question is about the 64 bit WWN. One reference claims the terms WWN and WWPN are synonymous. An online source seems to refute this. They say: A WWPN (world wide port name) is the unique identifier for a fibre channel port where a WWN (world wide name) the unique identifier for the node itself. A good example is a dual port HBA. There will be two WWPN's (one for each port) and only a single WWN for the card itself. Question #1: Which is correct? I’m almost positive I read that every “Port” has a WWN. My next question is about the 24 bit FC address that is dynamically allocated to a port when it is introduced to the switch. The Domain ID field is defined as: "a unique number provided to each switch in the fabric." Question #2: Do Domain IDs only apply to switch ports? For example what would the Domain ID be for a HBA? None? The same as the switch port it is connected to? Question #3: My last question is about the Name Server of a switch. A book example shows the routing of a message through the switch. It uses the WWNs of the source and destination ports to route the message. I am assuming that the Name Server must associate the WWN and the FC address in some way in order to route the message, correct?

  Read the article

• How to make Ubuntu recognize an unknown external display (so I can adjust its resolution)?

  - by WagnerAA

  I have a Dell laptop with an external monitor attached (a Samsumg SyncMaster 931c). My laptop display was recognized, and I can adjust its optimum resolution. My external display is still unknown, thus I'm stuck at a lower resolution (1024x768): I tried the "Detect Displays" button, but it didn't work, nothing happens. I recently upgraded from Ubuntu 12.04 to 12.10. Things were working before. I don't know if I can actually change this configuration, or if this is a bug. I searched for an answer here and also in Launchpad's website, but found none. I even tried to install Nvidia drivers, and just messed things up. It seems I wasn't even using nvidia before, as I guessed by looking at my additional drivers configuration: My laptop has an Intel chipset, I guess: $ dpkg --get-selections | grep -i -e nvidia -e intel intel-gpu-tools install libdrm-intel1:amd64 install libdrm-intel1:i386 install nvidia-common install xserver-xorg-video-intel install I don't have an xorg.conf file (I think this is nvidia related, am I right?): $ cat /etc/X11/xorg.conf cat: /etc/X11/xorg.conf: No such file or directory $ ls -l /etc/X11/ total 76 drwxr-xr-x 2 root root 4096 Out 19 23:41 app-defaults drwxr-xr-x 2 root root 4096 Abr 25 2012 cursors -rw-r--r-- 1 root root 18 Abr 25 2012 default-display-manager drwxr-xr-x 4 root root 4096 Abr 25 2012 fonts -rw-r--r-- 1 root root 17394 Dez 3 2009 rgb.txt lrwxrwxrwx 1 root root 13 Mai 1 03:33 X -> /usr/bin/Xorg drwxr-xr-x 3 root root 4096 Out 19 23:41 xinit drwxr-xr-x 2 root root 4096 Jan 23 2012 xkb -rw-r--r-- 1 root root 0 Out 24 08:55 xorg.conf.nvidia-xconfig-original -rwxr-xr-x 1 root root 709 Abr 1 2010 Xreset drwxr-xr-x 2 root root 4096 Out 19 10:08 Xreset.d drwxr-xr-x 2 root root 4096 Out 19 10:08 Xresources -rwxr-xr-x 1 root root 3730 Jan 20 2012 Xsession drwxr-xr-x 2 root root 4096 Out 20 00:11 Xsession.d -rw-r--r-- 1 root root 265 Jul 1 2008 Xsession.options -rw-r--r-- 1 root root 13 Ago 15 06:43 XvMCConfig -rw-r--r-- 1 root root 601 Abr 25 2012 Xwrapper.config Here is some information I gathered by looking at other related posts: $ sudo lshw -C display; lsb_release -a; uname -a *-display:0 description: VGA compatible controller product: Mobile 4 Series Chipset Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 07 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:48 memory:f6800000-f6bfffff memory:d0000000-dfffffff ioport:1800(size=8) *-display:1 UNCLAIMED description: Display controller product: Mobile 4 Series Chipset Integrated Graphics Controller vendor: Intel Corporation physical id: 2.1 bus info: pci@0000:00:02.1 version: 07 width: 64 bits clock: 33MHz capabilities: pm bus_master cap_list configuration: latency=0 resources: memory:f6100000-f61fffff LSB Version: core-2.0-amd64:core-2.0-noarch:core-3.0-amd64:core-3.0-noarch:core-3.1-amd64:core-3.1-noarch:core-3.2-amd64:core-3.2-noarch:core-4.0-amd64:core-4.0-noarch:cxx-3.0-amd64:cxx-3.0-noarch:cxx-3.1-amd64:cxx-3.1-noarch:cxx-3.2-amd64:cxx-3.2-noarch:cxx-4.0-amd64:cxx-4.0-noarch:desktop-3.1-amd64:desktop-3.1-noarch:desktop-3.2-amd64:desktop-3.2-noarch:desktop-4.0-amd64:desktop-4.0-noarch:graphics-2.0-amd64:graphics-2.0-noarch:graphics-3.0-amd64:graphics-3.0-noarch:graphics-3.1-amd64:graphics-3.1-noarch:graphics-3.2-amd64:graphics-3.2-noarch:graphics-4.0-amd64:graphics-4.0-noarch:printing-3.2-amd64:printing-3.2-noarch:printing-4.0-amd64:printing-4.0-noarch:qt4-3.1-amd64:qt4-3.1-noarch Distributor ID: Ubuntu Description: Ubuntu 12.10 Release: 12.10 Codename: quantal Linux Batcave 3.5.0-17-generic #28-Ubuntu SMP Tue Oct 9 19:31:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux $ xrandr -q Screen 0: minimum 320 x 200, current 2304 x 800, maximum 32767 x 32767 LVDS1 connected 1280x800+0+0 (normal left inverted right x axis y axis) 286mm x 1790mm 1280x800 59.9*+ 1024x768 60.0 800x600 60.3 56.2 640x480 59.9 VGA1 connected 1024x768+1280+32 (normal left inverted right x axis y axis) 0mm x 0mm 1024x768 60.0* 800x600 60.3 56.2 848x480 60.0 640x480 59.9 DP1 disconnected (normal left inverted right x axis y axis) If there's anything else I can do, any other information I can post here, to help me configure this external display, please let me know. If this is actually a bug, I apologize (I know bugs are not allowed here), but I really wasn't sure. And I will promptly file a bug report in Launchpad if that's the case. Thanks a lot in advance. ;)

  Read the article

• Daisy-chainable DisplayPort Monitors

  - by thepurplepixel

  I am the proud new owner of a MacBook Pro with a mini-DisplayPort. My desk setup used to allow me to position the screen of my old MacBook beside an external monitor, essentially allowing dual-head. It was also advantageous that my old MBP and my external monitor had the same resolution, 1440x900. Now, I'm searching for a set of two monitors that I can use a HengeDock with. Unfortunately, the MacBook Pro suffers from having only one mini-DisplayPort. Looking up the spec for DisplayPort 1.2 (which the MBP supports), DisplayPort daisy chaining is supported. What I'm looking for is a monitor that has two DisplayPorts so I can daisy chain two monitors off the single mini-DisplayPort. What I don't want is a USB-based video solution. I need full acceleration on both monitors; an external video card won't cut it. I hope I don't have to wait a few years for these monitors to come out. TL;DR: I need two monitors with two DisplayPorts each that I can daisy-chain. Thanks!

  Read the article

• 2560 x 1600 screen resolution not available when a second monitor is attached.

  - by sgmoore

  I am running Windows 7 (64-bit edition) and have a 30" Dell 3007WFP monitor which runs at a screen resolution of 2560 x 1600. This works perfectly until I try to connect a second monitor, and then the screen resolution on the main monitor immediately drops to 1280x800 and I can't change it back up to the correct resolution until I disconnect the second monitor. The graphics card is a Nvidia Quadro FX 370. This has a dual link DVI connector (to which the 30" is connected) and a single link DVI connector. The second monitor can run at 1920x1080 and is connected using a VGA to DVI connector. Note, it does not seem to matter whether the second monitor is running at 1920x1080 or even at 800x600. Windows reports Total Available Graphics Memory: 3839MB Dedicated Video Memory: 256MB System Video Memory: 0MB Shared System Memory: 3583MB Does anyone know if this a limitation with the video card, memory, drivers, connectors or something else? If this is a limitation with the video card, can anyone recommend a PCI Express 16 card that would support at least this setup, but preferably support two 30" monitors both running 2560 x 1600. (I'm not into gaming etc, so it doesn't need to be very powerful)

  Read the article

• Multi monitor setup with a tv as well?

  - by jasondavis

  I have always had a dual monitor setup for my pc's for years now. I am now in the market to build a new PC and get some new stuff. I need some help or advice on how to run 3 monitors WITH a 4th display which will be a lcd/plasma tv. So I am thinking I can get 2 video cards and that will give me all the hookups to run 3 monitors instead of 2. I will mount all 3 monitors in a row side by side and above them on the wall I would like to mount a larger 30-40+ inch lcd or plasma tv. I would then like to hook up my atelite/cable to this tv just as I would normally hook up a tv but I would like to also be able to have an option to view my PC o this tv as well. I know that is possible but would it be possible to view my PC on that tv and also still view my 3 other monitors and have the TV be a 4th display, where I could dock a different app/window in windows in all 4 displays (3 monitors + tv) ?? Please tell me any tips/advice on how to do this including what cables/software if any/converters/ you name it. Thanks for any help

  Read the article

• How far should we take the N+N redundancy craziness ?

  - by Brann

  The industry standard when it comes from redundancy is quite high, to say the least. To illustrate my point, here is my current setup (I'm running a financial service). Each server has a RAID array in case something goes wrong on one hard drive .... and in case something goes wrong on the server, it's mirrored by another spare identical server ... and both server cannot go down at the same time, because I've got redundant power, and redundant network connectivity, etc ... and my hosting center itself has dual electricity connections to two different energy providers, and redundant network connectivity, and redundant toilets in case the two security guards (sorry, four) needs to use it at the same time ... and in case something goes wrong anyway (a nuclear nuke? can't think of anything else), I've got another identical hosting facility in another country with the exact same setup. Cost of reputational damage if down = very high Probability of a hardware failure with my setup : <<1% Probability of a hardware failure with a less paranoiac setup : <<1% ASWELL Probability of a software failure in our application code : 1% (if your software is never down because of bugs, then I suggest you doublecheck your reporting/monitoring system is not down. Even SQLServer - which is arguably developed and tested by clever people with a strong methodology - is sometimes down) In other words, I feel like I could host a cheap laptop in my mother's flat, and the human/software problems would still be my higher risk. Of course, there are other things to take into consideration such as : scalability data security the clients expectations that you meet the industry standard But still, hosting two servers in two different data centers (without extra spare servers, nor doubled network equipment apart from the one provided by my hosting facility) would provide me with the scalability and the physical security I need. I feel like we're reaching a point where redundancy is just a communcation tool. Honestly, what's the difference between a 99.999% uptime and a 99.9999% uptime when you know you'll be down 1% of the time because of software bugs ? How far do you push your redundancy crazyness ?

  Read the article

• Windows 7 boots to black screen with blinking cursor

  - by murgatroid99

  I have an Alienware M17x that dual boots into Ubuntu 11.04 and Windows 7 Home Premium. Currently, the computer starts at the GRUB loader and will boot into Ubuntu, but if I try to boot into Windows, I immediately get a black screen with a blinking cursor in the upper left corner. The output of fdisk -l is Device Boot Start End Blocks Id System /dev/dm-0p1 1 5 40131 de Dell Utility Partition 1 does not start on physical sector boundary. /dev/dm-0p2 6 1918 15360000 7 HPFS/NTFS Partition 2 does not start on physical sector boundary. /dev/dm-0p3 * 1918 64772 504878877+ 7 HPFS/NTFS Partition 3 does not start on physical sector boundary. /dev/dm-0p4 64772 77827 104858625 5 Extended Partition 4 does not start on physical sector boundary. /dev/dm-0p5 64772 67204 19531008 83 Linux /dev/dm-0p6 67204 74498 58593536 83 Linux /dev/dm-0p7 74498 77577 24731648 83 Linux /dev/dm-0p8 77578 77827 2000128 82 Linux swap / Solaris I have used the Windows rescue CD, and run the automatic error fixer until it finds no errors. I have run chkdsk /R on both the main Windows 7 (/dev/dm-0p3) partition and the recovery partition (/dev/dm-0p2). I set the main Windows 7 partition to be active. I also tried running in the recovery console the commands bootrec /fixmbr bootrec /fixboot bootrec /rebuildbcd None of these helped and the last set of commands deletes grub, which I then have to reinstall from Ubuntu. I think the last thing I did in windows before this started was install the newest ATI driver for my video card. This would suggest using system restore, and I actually had a restore point earlier (after the problem started), but after whatever I did that restore point does not appear in the list on the recovery disk any more, so I cannot do a system restore. Is there anything else I can try to make Windows boot properly again? Edit: Running the suggested commands bootsect /nt60 c: bcdboot c:\windows /s c: was also ineffective.

  Read the article

• Proxmox drbd configuration split brain [on hold]

  - by AudioDan

  I am planning a proxmox HA configuration with two Dell R710 machines (dual 6 core processors in each) with enterprise level drive raid arrays. I would be using DRBD with a quorum disk on a third machine. I would dedicate two 1GB nics on each server to the DRBD communications. We would have approximately 12 to 14 Virtual Machines running on this pair of servers. The proxmox manual recommends creating two DRBD resources - one for the Virtual Machines that normally run on ServerA and one for the Virtual Machines that normally run on ServerB. This is because of the Primary/Primary state in which this configuration runs. If both servers have VMs talking to the same DRBD resource and a split brain situation occurs, there is potential for data corruption that must be resolved. While I understand it would take more effort to create new virtual machines, can anybody foresee any potential problems with running a separate DRBD resource for each VM instead? Does anyone have experience running a setup that way and has it worked well? It seems to me that would allow more flexibility in moving machines back and forth.

  Read the article

• Power issues Foxconn Barebones kit

  - by alpha1

  I have a Foxconn R20D2 bought about a year and a half ago. It ran fine for a while and then around last summer it started having power issues. I chalked it up to changes in electric current due to the overwhelmed grid when people turn on their AC units, but this problem has stayed for all year, shutting off randomly, shutting off when i turn on a vacuum and similar problems. Now that its summer again, the box basically sits there all day cycling itself, and now has gotten to the point it tried to boot and after 3 seconds, fails, shuts off and tried again. I know its power related, it runs opensuse linux and there are never any shutdown logs or anything of that sort. As the weather got hotter i noticed it happening more and more, and it most often happened in the morning, i presume as people woke up and turn on the AC. The power supply is a Chennel well technology co LTD model DSL-150. 150W max output. Its an intel atom dual core, with 2 sata drives, no CD/floppy etc, recently upgrades from 2 to 4gb of ram. It runs at 104 degrees Fahrenheit all the time almost. Any way i can test the power supply or anything else to try to fix it? Im a software guy, not hardware so im at a complete loss here, thanks for all assistance you can provide! EDIT: The switch on the back that says 230 or 115 is set to 230. If im in the USA, could that be causing the problems?

  Read the article

• Windows 7 loses correct time zone upon reboot

  - by Android Eve

  I have a standard PC running Windows 7 Ultimate (64-bit). For some reason, it refuses to keep the correct time zone (the BIOS battery is OK) when restarted. Note (1): The Time zone is correct. The "Internet Time" tab also shows "this computer is set to automatically synchronize with 'time.windows.com'. When I click the 'Change settings...' button, the 'Synchronize with an Internet time server' checkbox is checked. Still, upon reboot, the time is skewed by 6 hours... and doesn't correct itself even after waiting hours for this "automatically synchronize" to occur. Note (2): The BIOS time is set to local (i.e. not UTC). When I restart Windows 7 without booting to the other OS installed in dual-boot config (Ubuntu Linux), it seems to correctly remember the time. This may explain immediate time upon reboot, but it doesn't explain why Windows 7 won't automatically 'Synchronize with an Internet time server' even after an hour. Why is this happening and how do I correct this?

  Read the article

• KeePass lost password and/or corruption due to Dropbox/KeePassX

  - by GummiV

  I started using Keepass about a month ago to hold my passwords and online accounts info. Everything was stored in a single .kdb file, only protected with a password. I'm using Windows 7. Now Keepass can't open my .kdb file with the error "Invalid/wrong key". I'm fairly confident I have the right password. Altough I might have mixed up a few letters I've tried about two dozen different combinations to minimize that possibility - but can't rule it out though. My guess is however that the .kdb file got corrupted, either due to Dropbox syncing (only using it on one computer though) or because I edited the file using KeePassX on Ubuntu (dual boot on the same computer, accessing a mounted Win7 NTFS partition), or possibly a combination of both. I have tried restoring older versions(even the original one) from Dropbox and trying out all possible passwords without any luck. (which does seem to rule out KeePassX as the culprit, since oldest copies are before I edited the file from Ubuntu) I have tried opening the file with the "Repair KeePass Database file" which always gives the "0xA Invalid/corrupt file structure" (the same error for when a wrong password is typed). I was wondering if there was any way for me to salvage my hard-gathered data. I know generally that brute force cracking is not feasible, but since I can remember probably more than half of the usernames/passwords, any maybe the fact that one of them does come up fairly often (my go-to pass for trivial stuff), that might simplify the brute force process to a doable time frame. Maybe the brute-force thing might incorporate the fact that I know the password length and what characters it's made from. (If we assume corruption, not a password-blackout on my part) I could do some programming if there are any libraries or routines that I could use. Other people seem to have had a similar probem http://forums.dropbox.com/topic.php?id=6199 http://forums.dropbox.com/topic.php?id=9139 http://www.keepassx.org/forum/viewtopic.php?t=1967&f=1 So hopefully this question will become a suitible resource for people when searching the web. Feel free to tell me if you think this should rather be a community wiki.

  Read the article

• sudo fdisk in a live session does not show all hard drives

  - by cornbread

  I am having Grub2 issues in my Ubuntu 10.04 dual boot, 2 hard drive system. So I am attempting to follow the standard grub2 reinstallation guide (cant post link because of spam filters allowing only one... ?_?) Don't know if this is the root of my problem, but my speedy internal HD with my OS on it is not showing up anywhere in a live session. Not in nautilus, behind fdisk.... no where. When I can get the main system to boot, there is no issue seeing all available partitions. But the live session sees only the 1TB internal media/backup hard drive. I need access to the other hard drive and it's partitions to finish the grub2 re-installation but I am not sure anymore that is the underlying issue. Anyone have experience with this? The issue I have identified as a grub2 issue is fully described here. SandPvvr describes it exactly. Some notes: I do not see the grub2 menu for my os's holding down the shift key after my bios screen works maybe 10% of the time Not related to reinstalling a windows os. havent been touched in a year do some web development. issue may have started when I was playing with ruby and django. not sure on this. Could a dev environment do this? fdisk in live session ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0001d518 Device Boot Start End Blocks Id System /dev/sdb2 1 121601 976759939 5 Extended /dev/sdb5 487 110765 885816036 83 Linux /dev/sdb6 110766 121601 87040138+ b W95 FAT32 /dev/sdb7 1 486 3903700+ 82 Linux swap / Solaris Partition table entries are not in disk order

  Read the article

• Very Slow DSL (ethernet) speed

  - by Abhijit

  I 'was' on opensuse 12.2 when my dsl speed was normal. Yesterday I switched from opensuse to ubuntu 12.04 and speed decreased. It came to range of 7-10-13-20-25-kbps. Then I switch to linux mint, and then to fedora. Still slow speed. When I was in ubuntu I disabled ipv6 but still no luck. Now I am in fedora but this time with DIFFERENT ISP. And still I am getting very slow sped. So my guess is this is nothing to do with os. What can be wrong? Is this problem of NIC? Does NIC speed decreases over time? Does NIC life ends over time as with keyboard or mouse? Help please All the os I used are 64 bit and my laptop is Compaq Presario A965Tu Intel Centrino DUal Core. Interesting thing to notice is I get normal speed while downloading torrent inside torrent client softwares. This slow speed issue applied to download from any web browser or installing software using terminal.

  Read the article

• Relaying to tech "support" that computer is actually broken.

  - by Sion

  First some background: I have a Dell Inspiron 15R M050, it is still under the Dell limited warranty and the Best Buy Extended warranty. I am currently dual booting Debian Squeeze and Windows 7, the only reason I go into Windows is to play video games specifically steam games. Issue: When I play my games in Windows I am capable of playing for anywhere from 5 minutes to 2 hours before I suffer a hard-lock. I cannot alt-tab, ctrl-alt-delete, ctrl-shift-escape do anything for 2-3 minutes. After this hard-lock period everything runs fine, I can continue the game for probably another hour at least before I suffer another lock. Games: Borderlands, Splinter Cell: Chaos Theory, Starcraft 2, Garrys Mod What I have tried: Running the diagnostic suite in the dell bios, restoring the OEM Windows recovery partition on the HD, fresh installing Windows 7 Professional, updating BIOS, Calling tech support and having them run a software Hardware Diagnostics suite. The question: I think from the research that I have performed that it might be a lack of thermal paste on the CPU, would I be able to go to Best Buy and have them do a hardware diagnostic from the hardware level then have them be able to tell Dell that there is a hardware issue? Or would there be a different problem?

  Read the article

• Load is 0, yet site crawls (sometimes). What gives?

  - by Yegor

  I have a ~1.5-2mil page views per day site running on 2 servers. One for mysql, other for everything else. Mysql box has a load of 3, frontend is usually 0.0-0.1. Both are dual quad core with 8GB ram running SAS drives in raid5. CPU is idle for majority of the time, iowait is non-existent. Im running nginx, memcache, and site is built on php. Half the time everything runs perfect, while at other times it lags something severe, when it takes 10-15 seconds for a page to load. Page execution time is always super low, but it seems to hang, waiting for something before it actually loads the page. Whats even more weird is that it only happens to 1 file on the site (but its the one thats most commonly accessed, that actually loads the content on the site). Other pages are super fast at all times, even when it takes 15 seconds to load actual content. I have nginx_stats plugin installed, and if I monitor it, the lag spikes happen when the write column starts going above 100, and it frequently does... all the way to 500-1000. It does so at totally random times... not when traffic is heavy... it can do this in the middle of the night, and work perfectly at 5pm when traffic is at its highest. Any ideas?

  Read the article

• Ubuntu and Windows and Separate HDs, oh my!

  - by LuxuryMode

  Need some major help. Running a Dell XPS/Dimension 630i. It came with "SATA 2 RAID 0 With Dual 500GB Hard Drives." I have installed a new, third non-raided drive and installed Ubuntu on it. So now I have Windows on the original hard drive and Ubuntu Linux on the new HD. When I get to the boot menu where I can select an OS, if I select windows I get an error: "No such drive, no such disk." Also, strangely in the first place, in order to even get to the bootloader menu I have had to disable ALL ports under the RAID config. Unless I do this, I will just get to a never-ending blinking cursor. I have tried every conceivable CMOS config and nothing else works. Tried setting port 3 (the new HD w/ Ubuntu) to first hard disk boot priority. Tried disabling all other ports and enabling the Ubuntu HD port and vice versa. Here's a pic of the error I get when I try to boot to Windows: http://imgur.com/TJ1mS. Also, please note that I can actually access all files from the raided Windows drive through Ubuntu. (Someone suggested just reinstalling windows from installation CD. Agree?)

  Read the article

< Previous Page | 146 147 148 149 150 151 152 153 154 155 156 157  | Next Page >