Search Results

Search found 14709 results on 589 pages for 'root permission'.

Page 150/589 | < Previous Page | 146 147 148 149 150 151 152 153 154 155 156 157  | Next Page >

• eth0:0 is configured but not listed in ifconfig output

  - by FractalizeR

  Hello. I have the following problem: My server was given two IPs from [b]different[/b] subnets. Now I am trying to configure the system to work properly. I have created [root@server ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0 # Intel Corporation 80003ES2LAN Gigabit Ethernet Controller (Copper) HWADDR=00:30:48:DA:B1:0E DEVICE=eth0 BOOTPROTO=none BROADCAST=79.174.69.255 IPADDR=79.174.69.241 NETMASK=255.255.254.0 NETWORK=79.174.68.0 ONBOOT=yes GATEWAY=79.174.68.1 TYPE=Ethernet [root@server ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0:0 # Intel Corporation 80003ES2LAN Gigabit Ethernet Controller (Copper) HWADDR=00:30:48:DA:B1:0E DEVICE=eth0 BOOTPROTO=none BROADCAST=79.174.69.255 IPADDR=79.174.71.74 NETMASK=255.255.255.0 NETWORK=79.174.71.1 ONBOOT=yes GATEWAY=79.174.71.1 TYPE=Ethernet But both after "service network restart" and after "reboot" [root@server ~]# ifconfig eth0 Link encap:Ethernet HWaddr 00:30:48:DA:B1:0E inet addr:79.174.71.74 Bcast:79.174.71.255 Mask:255.255.255.0 inet6 addr: fe80::230:48ff:feda:b10e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:910284 errors:0 dropped:0 overruns:0 frame:0 TX packets:2924 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:257964879 (246.0 MiB) TX bytes:232450 (227.0 KiB) Memory:df220000-df240000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:27 errors:0 dropped:0 overruns:0 frame:0 TX packets:27 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6976 (6.8 KiB) TX bytes:6976 (6.8 KiB) Device eth0:0 is not shown as active. If I try [root@server ~]# ifconfig eth0:0 eth0:0 Link encap:Ethernet HWaddr 00:30:48:DA:B1:0E UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:df220000-df240000 It is shown as up and running, but IP is not assigned to it. Also it is strange, that IP address assigned to eth0:0 in config file is used by eth0. /var/log/messages shows nothing about network configuration errors on either eth0 or eth0:0. system-config-network seem to understand all settings correctly and resaves them ok also. "ifup eth0:0" executes ok, but ifconfig afterwards shows no eth0:0 device after that. What did I do wrong? May be the problem is that IPs are from different subnets?

  Read the article

• Error "403 Forbidden" on Sharepoint Search Settings Page

  - by user21924

  Hello I thought I had solved this nightmare by re-entering the values in my SSP properties set up, however accessing the Search Settings page error has reared it ugly head again. Now all solutions point to this method listed here * http://www.routtlogics.com/blog/Lists/Posts/Post.aspx?ID=6 * http://social.technet.microsoft.com/Forums/en-US/sharepointadmin/thread/f00651cd-e452-45b9-b19e-90e89c3c3ad4 * http://blogs.technet.com/sushrao/archive/2009/03/26/microsoft-office-sharepoint-server-2007-moss-403-forbidden-error-when-clicked-on-search-settings-page.aspx The above workaround(s) basically states that granting the local group WSS_WPG read and write permission to the Task folder in the Windows directory would solve the problem, however whenever I try to change to the permission attribute of this folder I get an access denied message, even when logged in as a Domain administrator, Enterprise and even the SharePoint Farm administrator. Please guys how do I get around this access denied issue. Thanks

  Read the article

• GConf error and gnome does not load properly in RHEL 5.3

  - by Tim

  Hello, I am using Red Hat Enterprise Linux 5.3 . I created a user oracle on the system, using the following command useradd -g oinstall -G dba,oper -d /home/oracle oracle Now, when i try to login as the user oracle, GNOME does not load properly and i get popup box error message like the following GConf error:Failed to contact configuration server;some possible causes are that you need to enable TCP/IP for ORBit,or your have NFS locks due to a system crash.(Details-/:IOR file'/tmp/gcofd-cheetahman/tock/ior' not opened successfully,no gconfd located:Permission denied 2: IOR file /tmp/gconfd-cheetahman/lock/ior not opened succesfully no gconfd located: Permission denied) Any way to fix this ? Thank You

  Read the article

• X11 from ssh on Mac OSX to Linux server doesn't work --- Gtk-WARNING **: cannot open display

  - by Cal

  Hello, I installed a program wireshark on my remote linux box and I'm trying to run it with X11 from my mac computer using SSH. Here's my terminal... macosx$ echo $DISPLAY /tmp/launch-f4w6k6/:0 macosx$ ssh -X [email protected] [email protected]'s password: remoteubuntu:~# echo $DISPLAY remoteubuntu:~# wireshark (wireshark:18927): Gtk-WARNING **: cannot open display: Here's a few lines from /etc/ssh/sshd_config X11Forwarding yes X11DisplayOffset 10 PrintMotd no PrintLastLog yes TCPKeepAlive yes #UseLogin no Thanks for the help!

  Read the article

• Administrator not an Administrator?

  - by Sonny Ordell

  I have copied some files from an XP computer to a PC running Windows 7. I am logged on as a user who is marked as an Administrator. When I try to access the directory, I am told I don't have permission. Understandable, but what is odd is that I as an administrator don't have access to take ownership of the files. I don't have permission to add users in the ACL or to take ownership, indeed such options are greyed out. Why as an administrator user can I not take ownership of files?

  Read the article

• IIS 7.5 FTP IIS Manager Users Login Fail (530)

  - by Jim

  IIS 7.5 FTP IIS Manager Users Login Fail (530) I'm trying to set up a FTP site on IIS 7.5 that allows IIS Manager Users to login. I'm following this guide: http://learn.iis.net/page.aspx/321/configure-ftp-with-iis-7-manager-authentication/. After set up, I cannot login to the FTP using an IIS Manager User account. The client error I got was 530 User cannot log in. Win32 error: Unspecified error. Error details: An error occured during the authentication process. I tried both with or without a virtual host. A Windows account login fine. The only strange thing I noticed was that when setting up Read permission for Network Service, there was an access denied error when setting up permission for "%SystemDrive%\Windows\System32\inetsrv\config\schema". Any thoughts? Thanks!

  Read the article

• Writting this Bash Script to accept Arguments?

  - by Urda

  How would I go about converting this bash script: mkdir /store/sftp/%USERNAME% sudo useradd -d /incoming %USERNAME% sudo passwd %USERNAME% ## Password needs to be typed or passed in here sudo usermod -g sftp %USERNAME% sudo usermod -s /bin/false %USERNAME% sudo chmod 755 /store/sftp/%USERNAME% sudo chown root:root /store/sftp/%USERNAME% sudo mkdir /store/sftp/%USERNAME%/incoming sudo chown %USERNAME%:sftp /store/sftp/%USERNAME%/incoming To accpet a username and a password?

  Read the article

• Mounting NFS share between OSX and Centos VM

  - by Adam

  I'm having issues mounting an NFS share I've made on my Mac host (server) from a Centos VM (client). I'm getting a permission denied error. I have this line in /etc/exports on server: /Users/adam/Sites/ 192.168.1.223(rw) and in /etc/fstab on client: 192.168.1.186:/Users/adam/Sites/ /home/adam/Sites/ nfs rw 0 0 I'm sure this is a simple configuration issue, but I've never set up NFS properly before. Extra info: # mount -v 192.168.1.186:/Users/adam/Sites/ /home/adam/Sites/ mount: no type was given - I'll assume nfs because of the colon mount.nfs: timeout set for Mon Nov 26 07:31:40 2012 mount.nfs: trying text-based options 'vers=4,addr=192.168.1.186,clientaddr=192.168.1.223' mount.nfs: mount(2): Protocol not supported mount.nfs: trying text-based options 'addr=192.168.1.186' mount.nfs: prog 100003, trying vers=3, prot=6 mount.nfs: trying 192.168.1.186 prog 100003 vers 3 prot TCP port 2049 mount.nfs: prog 100005, trying vers=3, prot=17 mount.nfs: trying 192.168.1.186 prog 100005 vers 3 prot UDP port 958 mount.nfs: mount(2): Permission denied mount.nfs: access denied by server while mounting 192.168.1.186:/Users/adam/Sites/

  Read the article

• How do I install PHP with JSON and OAuth on Mac Snow Leopard?

  - by meilas

  I want to use the Dropbox API via this library, http://code.google.com/p/dropbox-php/. I installed MAMP, and then I tried sudo pecl install oauth but I got the following. >>>> downloading oauth-1.0.0.tgz ... Starting to download oauth-1.0.0.tgz (42,834 bytes) ............done: 42,834 bytes 6 source files, building running: phpize Configuring for: PHP Api Version: 20090626 Zend Module Api No: 20090626 Zend Extension Api No: 220090626 building in /var/tmp/pear-build-root/oauth-1.0.0 running: /private/var/tmp/apache_mod_php/apache_mod_php-53~1/Build/tmp/pear/temp/oauth/configure checking for grep that handles long lines and -e... /usr/bin/grep checking for egrep... /usr/bin/grep -E checking for a sed that does not truncate output... /opt/local/bin/gsed checking for cc... cc checking for C compiler default output file name... a.out checking whether the C compiler works... yes checking whether we are cross compiling... no checking for suffix of executables... checking for suffix of object files... o checking whether we are using the GNU C compiler... yes checking whether cc accepts -g... yes checking for cc option to accept ISO C89... none needed checking how to run the C preprocessor... cc -E checking for icc... no checking for suncc... no checking whether cc understands -c and -o together... yes checking for system library directory... lib checking if compiler supports -R... no checking if compiler supports -Wl,-rpath,... yes checking build system type... i686-apple-darwin10.4.0 checking host system type... i686-apple-darwin10.4.0 checking target system type... i686-apple-darwin10.4.0 checking for PHP prefix... /usr checking for PHP includes... -I/usr/include/php -I/usr/include/php/main -I/usr/include/php/TSRM -I/usr/include/php/Zend -I/usr/include/php/ext -I/usr/include/php/ext/date/lib checking for PHP extension directory... /usr/lib/php/extensions/no-debug-non-zts-20090626 checking for PHP installed headers prefix... /usr/include/php checking if debug is enabled... no checking if zts is enabled... no checking for re2c... no configure: WARNING: You will need re2c 0.13.4 or later if you want to regenerate PHP parsers. checking for gawk... gawk checking for oauth support... yes, shared checking for cURL in default path... found in /usr checking for ld used by cc... /usr/libexec/gcc/i686-apple-darwin10/4.2.1/ld checking if the linker (/usr/libexec/gcc/i686-apple-darwin10/4.2.1/ld) is GNU ld... no checking for /usr/libexec/gcc/i686-apple-darwin10/4.2.1/ld option to reload object files... -r checking for BSD-compatible nm... /usr/bin/nm checking whether ln -s works... yes checking how to recognise dependent libraries... pass_all checking for ANSI C header files... yes checking for sys/types.h... yes checking for sys/stat.h... yes checking for stdlib.h... yes checking for string.h... yes checking for memory.h... yes checking for strings.h... yes checking for inttypes.h... yes checking for stdint.h... yes checking for unistd.h... yes checking dlfcn.h usability... yes checking dlfcn.h presence... yes checking for dlfcn.h... yes checking the maximum length of command line arguments... 196608 checking command to parse /usr/bin/nm output from cc object... rm: conftest.dSYM: is a directory rm: conftest.dSYM: is a directory rm: conftest.dSYM: is a directory rm: conftest.dSYM: is a directory ok checking for objdir... .libs checking for ar... ar checking for ranlib... ranlib checking for strip... strip rm: conftest.dSYM: is a directory rm: conftest.dSYM: is a directory checking if cc static flag works... rm: conftest.dSYM: is a directory yes checking if cc supports -fno-rtti -fno-exceptions... rm: conftest.dSYM: is a directory no checking for cc option to produce PIC... -fno-common checking if cc PIC flag -fno-common works... rm: conftest.dSYM: is a directory yes checking if cc supports -c -o file.o... rm: conftest.dSYM: is a directory yes checking whether the cc linker (/usr/libexec/gcc/i686-apple-darwin10/4.2.1/ld) supports shared libraries... yes checking dynamic linker characteristics... darwin10.4.0 dyld checking how to hardcode library paths into programs... immediate checking whether stripping libraries is possible... yes checking if libtool supports shared libraries... yes checking whether to build shared libraries... yes checking whether to build static libraries... no >>>> creating libtool appending configuration tag "CXX" to libtool configure: creating ./config.status config.status: creating config.h running: make /bin/sh /private/var/tmp/pear-build-root/oauth-1.0.0/libtool --mode=compile cc -I. -I/private/var/tmp/apache_mod_php/apache_mod_php-53~1/Build/tmp/pear/temp/oauth -DPHP_ATOM_INC -I/private/var/tmp/pear-build-root/oauth-1.0.0/include -I/private/var/tmp/pear-build-root/oauth-1.0.0/main -I/private/var/tmp/apache_mod_php/apache_mod_php-53~1/Build/tmp/pear/temp/oauth -I/usr/include/php -I/usr/include/php/main -I/usr/include/php/TSRM -I/usr/include/php/Zend -I/usr/include/php/ext -I/usr/include/php/ext/date/lib -DHAVE_CONFIG_H -g -O2 -Wall -g -c /private/var/tmp/apache_mod_php/apache_mod_php-53~1/Build/tmp/pear/temp/oauth/oauth.c -o oauth.lo mkdir .libs cc -I. "-I/private/var/tmp/apache_mod_php/apache_mod_php-53~1/Build/tmp/pear/temp/oauth" -DPHP_ATOM_INC -I/private/var/tmp/pear-build-root/oauth-1.0.0/include -I/private/var/tmp/pear-build-root/oauth-1.0.0/main "-I/private/var/tmp/apache_mod_php/apache_mod_php-53~1/Build/tmp/pear/temp/oauth" -I/usr/include/php -I/usr/include/php/main -I/usr/include/php/TSRM -I/usr/include/php/Zend -I/usr/include/php/ext -I/usr/include/php/ext/date/lib -DHAVE_CONFIG_H -g -O2 -Wall -g -c "/private/var/tmp/apache_mod_php/apache_mod_php-53~1/Build/tmp/pear/temp/oauth/oauth.c" -fno-common -DPIC -o .libs/oauth.o In file included from /private/var/tmp/apache_mod_php/apache_mod_php-53~1/Build/tmp/pear/temp/oauth/php_oauth.h:47, from /private/var/tmp/apache_mod_php/apache_mod_php-53~1/Build/tmp/pear/temp/oauth/oauth.c:14: /usr/include/php/ext/pcre/php_pcre.h:29:18: error: pcre.h: No such file or directory In file included from /private/var/tmp/apache_mod_php/apache_mod_php-53~1/Build/tmp/pear/temp/oauth/php_oauth.h:47, from /private/var/tmp/apache_mod_php/apache_mod_php-53~1/Build/tmp/pear/temp/oauth/oauth.c:14: /usr/include/php/ext/pcre/php_pcre.h:37: error: expected '=', ',', ';', 'asm' or '__attribute__' before '*' token /usr/include/php/ext/pcre/php_pcre.h:38: error: expected '=', ',', ';', 'asm' or '__attribute__' before '*' token /usr/include/php/ext/pcre/php_pcre.h:44: error: expected specifier-qualifier-list before 'pcre' make: *** [oauth.lo] Error 1 ERROR: `make' failed </block>

  Read the article

• ASP.NET Security Exception when Switch IIS7 to Use UNC Path for Content

  - by Jeremy H.

  I have a Windows Server 2008 R2 box running IIS7.5 with Medium Trust configured for ASP.NET. When I have the website running from local content (e.g.: c:\inetpub\wwwroot) everything works fine. When I change IIS to use a UNC path for the content (e.g.: \\computer\wwwroot) I get the following error: Security Exception Description: The application attempted to perform an operation not allowed by the security policy. To grant this application the required permission please contact your system administrator or change the application's trust level in the configuration file. Exception Details: System.Security.SecurityException: Request for the permission of type 'System.Data.SqlClient.SqlClientPermission, System.Data, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089' failed. I'm trying to figure out why ASP.NET/IIS would allow for the SQL call when using local content but not when using a UNC path. Any ideas what I need to do to use a UNC path from IIS7 properly?

  Read the article

• How to connect SAN from CentOS through two iSCSI Targets

  - by garconcn

  I had asked the similar question before. This time I want to use subnet for two iSCSI Targets, hence I start a new question. I have an old Promise VTrak M500i SAN Server. It comes with 2 iSCSI ports. I want to connect to two LUNs on the SAN server through two separate Targets from CentOS 5.7 64bits server. My network setup is as follows: CentOS server: Management network - 192.168.1.1 Storage network 1 - 192.168.5.2 Storage network 2 - 192.168.6.2 Promise SAN server: Management network - 192.168.1.2 iSCSI Port 1 - 192.168.5.1 iSCSI Port 2 - 192.168.6.1 I have two Logical Drives on this SAN and they are mapped as follows: Index Initiator Name LUN Mapping 0 iqn.2011-11:backup (LD0,0) 1 iqn.2011-11:template (LD1,1) Basically, I want the traffic to iqn.2011-11:backup LUN 0 through 192.168.5.1 network the traffic to iqn.2011-11:template LUN 1 through 192.168.6.1 network I don't use MPIO, just want to separate the traffic to avoid traffic jam. How do I achieve this? I am new to SAN stuff, please explain as much detail as you can. Thank you. The following are what I am doing now. After mapping the LUN to my pre-defined Initiators, the CentOS server can discover both Targets. [root@centos ~]# iscsiadm -m discovery -t sendtargets -p 192.168.5.1 192.168.5.1:3260,1 iscsi-1 192.168.6.1:3260,2 iscsi-1 [root@centos ~]# iscsiadm -m discovery -t sendtargets -p 192.168.6.1 192.168.6.1:3260,2 iscsi-1 192.168.5.1:3260,1 iscsi-1 [root@centos ~]# /etc/init.d/iscsi start iscsid is stopped Starting iSCSI daemon: [ OK ] [ OK ] Setting up iSCSI targets: Logging in to [iface: default, target: iscsi-1, portal: 192.168.6.1,3260] Logging in to [iface: default, target: iscsi-1, portal: 192.168.5.1,3260] Login to [iface: default, target: iscsi-1, portal: 192.168.6.1,3260] successful. Login to [iface: default, target: iscsi-1, portal: 192.168.5.1,3260] successful. [ OK ] [root@centos ~]# iscsiadm -m session tcp: [1] 192.168.6.1:3260,2 iscsi-1 tcp: [2] 192.168.5.1:3260,1 iscsi-1 When I check the LUN mapping on the SAN server for the two Logical Drives, both LUNs are connected through Port0-192.168.5.2 with the Initiator defined in CentOS. Assigned Initiator List: Initiator Name Alias IP Address LUN iqn.2011-11.centos centos.mydomain.com Port0-192.168.5.2 0 Initiator Name Alias IP Address LUN iqn.2011-11.centos centos.mydomain.com Port1-192.168.5.2 1 I assume the following is what I want: Initiator Name Alias IP Address LUN iqn.2011-11.backup centos.mydomain.com Port0-192.168.5.2 0 Initiator Name Alias IP Address LUN iqn.2011-11.template centos.mydomain.com Port0-192.168.6.2 1

  Read the article

• Error "403 Forbidden" on Sharepoint Search Settings Page

  - by user21924

  Hello I thought I had solved this nightmare by re-entering the values in my SSP properties set up, however accessing the Search Settings page error has reared it ugly head again. Now all solutions point to this method listed here * http://www.routtlogics.com/blog/Lists/Posts/Post.aspx?ID=6 * http://social.technet.microsoft.com/Forums/en-US/sharepointadmin/thread/f00651cd-e452-45b9-b19e-90e89c3c3ad4 * http://blogs.technet.com/sushrao/archive/2009/03/26/microsoft-office-sharepoint-server-2007-moss-403-forbidden-error-when-clicked-on-search-settings-page.aspx The above workaround(s) basically states that granting the local group WSS_WPG read and write permission to the Task folder in the Windows directory would solve the problem, however whenever I try to change to the permission attribute of this folder I get an access denied message, even when logged in as a Domain administrator, Enterprise and even the SharePoint Farm administrator. Please guys how do I get around this access denied issue. Thanks

  Read the article

• Graphite SQLite3 DatabaseError: attempt to write a readonly database

  - by Anadi Misra

  Running graphite under apache httpd, with slqite database, I have the correct folder permissions [root@liaan55 httpd]# ls -ltr /var/lib | grep graphite drwxr-xr-x. 2 apache apache 4096 Aug 23 19:36 graphite-web and [root@liaan55 httpd]# ls -ltr /var/lib/graphite-web/ total 68 -rw-r--r--. 1 apache apache 65536 Aug 23 19:46 graphite.db syncdb also seems to have gone fine [root@liaan55 httpd]# sudo -su apache bash-4.1$ whoami apache bash-4.1$ python /usr/lib/python2.6/site-packages/graphite/manage.py syncdb /usr/lib/python2.6/site-packages/graphite/settings.py:231: UserWarning: SECRET_KEY is set to an unsafe default. This should be set in local_settings.py for better security warn('SECRET_KEY is set to an unsafe default. This should be set in local_settings.py for better security') /usr/lib/python2.6/site-packages/django/conf/__init__.py:75: DeprecationWarning: The ADMIN_MEDIA_PREFIX setting has been removed; use STATIC_URL instead. "use STATIC_URL instead.", DeprecationWarning) /usr/lib/python2.6/site-packages/django/core/cache/__init__.py:82: DeprecationWarning: settings.CACHE_* is deprecated; use settings.CACHES instead. DeprecationWarning Creating tables ... Creating table account_profile Creating table account_variable Creating table account_view Creating table account_window Creating table account_mygraph Creating table dashboard_dashboard_owners Creating table dashboard_dashboard Creating table events_event Creating table auth_permission Creating table auth_group_permissions Creating table auth_group Creating table auth_user_user_permissions Creating table auth_user_groups Creating table auth_user Creating table django_session Creating table django_admin_log Creating table django_content_type Creating table tagging_tag Creating table tagging_taggeditem You just installed Django's auth system, which means you don't have any superusers defined. Would you like to create one now? (yes/no): yes Username (leave blank to use 'apache'): root E-mail address: [email protected] Password: Password (again): Superuser created successfully. Installing custom SQL ... Installing indexes ... Installed 0 object(s) from 0 fixture(s) bash-4.1$ exit and the local-settings.py file is as follows STORAGE_DIR = '/var/lib/graphite-web' INDEX_FILE = '/var/lib/graphite-web/index' DATABASES = { 'default': { 'NAME': '/var/lib/graphite-web/graphite.db', 'ENGINE': 'django.db.backends.sqlite3', 'USER': '', 'PASSWORD': '', 'HOST': '', 'PORT': '' } } I still get this error [Sat Aug 23 19:47:17 2014] [error] [client 10.42.33.238] File "/usr/lib/python2.6/site-packages/django/db/backends/sqlite3/base.py", line 344, in execute [Sat Aug 23 19:47:17 2014] [error] [client 10.42.33.238] return Database.Cursor.execute(self, query, params) [Sat Aug 23 19:47:17 2014] [error] [client 10.42.33.238] DatabaseError: attempt to write a readonly database not sure what is missing in this configuration

  Read the article

• Django rewrites URL as IP address in browser - why?

  - by Mitch

  I am using django, nginx and apache. When I access my site with a URL (e.g., http://www.foo.com/) what appears in my browser address is the IP address with admin appended (e.g., http://123.45.67.890/admin/). When I access the site by IP, it is redirected as expected by django's urls.py (e.g., http://123.45.67.890/ - http://123.45.67.890/accounts/login/?next=/) I would like to have the name URL act the same way as the IP. That is, if the URL goes to a new view, the host in the browser address should remain the same and not change to the IP address. Where should I be looking to fix this? My files: ; cpa.com (apache) NameVirtualHost *:8080 <VirtualHost *:8080> AddOutputFilterByType DEFLATE text/html text/plain text/xml text/css text/javascript application/javascript application/x-javascript BrowserMatch ^Mozilla/4 gzip-only-text/html BrowserMatch ^Mozilla/4\.0[678] no-gzip BrowserMatch \bMSIE !no-gzip !gzip-only-text/htm DocumentRoot /path/to/root ServerName www.foo.com <IfModule mod_rpaf.c> RPAFenable On RPAFsethostname On RPAFproxy_ips 127.0.0.1 </IfModule> <Directory /public/static> AllowOverride None AddHandler mod_python .py PythonHandler mod_python.publisher </Directory> Alias / /dj <Location /> SetHandler python-program PythonPath "['/usr/lib/python2.5/site-packages/django', '/usr/lib/python2.5/site-packages/django/forms'] + sys.path" PythonHandler django.core.handlers.modpython SetEnv DJANGO_SETTINGS_MODULE dj.settings PythonDebug On </Location> </VirtualHost> ; ; ports.conf (apache) Listen 127.0.0.1:8080 ; ; cpa.conf (nginx) server { listen 80; server_name www.foo.com; location /static { root /var/public; index index.html; } location /cpa/js { root /var/public/js; } location /cpa/css { root /var/public/css; } location /djmedia { alias "/usr/lib/python2.5/site-packages/django/contrib/admin/media/"; } location / { include /etc/nginx/proxy.conf; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_pass http://127.0.0.1:8080; } } ; ; proxy.conf (nginx) proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; client_max_body_size 10m; client_body_buffer_size 128k; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 500; proxy_buffers 32 4k;

  Read the article

• Make my git user and apache user have read/write/delete access

  - by Mr A

  I am having permission problems on my server. I use user developer to pull my git repository on the server. Then apache uses its own apache user to do write and execute code. I always have the problems when the app wants to write something in the directory (i.e: log files, and cache ...) if I execute a cron job and it uses my developer rights and wants to add something to the folders that is written by apache. My question is how to have my developer have the same write/delete access as my apache and avoid permission conflicts with each other? I am not fluent on linux command so, it would help if you could provide links or simply examples of doing so. thanks.

  Read the article

• How to create a Windows 7 installation usb media from linux ? (to install Windows 7) - Help need to know better method

  - by Abel Coto

  I have been reading some web pages and posts here and in other forums about how to create a Windows 7 installation Usb media (to install windows 7 using a usb) from linux. I asked in technet about this , and they give me general ideas about how to do it I personally am not very familiar with linux, but basicaly all that you need to do... in whatever way you do it is the following: Format a usb flash drive, either fat32 or ntfs create a partition that is large enough to host the windows installation (give or take 3GB for 64bit, aroudn 2.5gb for 32bit) and mark that partition as active/bootable. Since this can be done with windows, but just as well with a tool like gparted, you should be able to do the same in debian. Once you have created that partition, mount the iso that you download, and copy all files starting from the root, into the root of the usb flash drive. That's all there's to it. There is a method that i found in various places,that is almost the same that the man of technet has said. But,there is a step,that in that method is done,that i don't know if it is really necessary,or not. Not allways dd works.Basically, the missing step was to write a proper boot sector to the usb stick, which can be done from linux with ms-sys. This works with the Win7 retail version. Here is the complete rundown again: Install ms-sys Check what device your usb media is asigned - here we will assume it is /dev/sdb. Delete all partitions, create a new one taking up all the space, set type to NTFS, and set it bootable: *# cfdisk /dev/sdb* Create NTFS filesystem: *# mkfs.ntfs -f /dev/sdb1* Mount iso and usb media: *# mount -o loop win7.iso /mnt/iso # mount /dev/sdb1 /mnt/usb* Copy over all files: *# cp -r /mnt/iso/* /mnt/usb/* Write Windows 7 MBR on usb stick: *# ms-sys -7 /dev/sdb* ...and you're done. Shouldn't the usb work without doing the last step "# ms-sys -7 /dev/sdb" or to make the usb bootable , is a must , not only to mark the partition as bootable ? Would be better use rsync instead of cp -r ? All this steps should be done as root, i suppose , or if not , chmod to 664 and chown the directories where are mounted the usb and the iso, no ? But i suppose that the easier thing is to copy the data as root , and that this will not affect to the data. Has anyone tried this method or some similar like copying the iso with dd ?

  Read the article

• problem with enabling remote management of hyper-v server 2008 r2

  - by Pai Gaudêncio

  Howdy, I just recently installed hyper-v server 2008 r2 on a dedicated server i have, but i'm having trouble enabling remote management. Running the HVRemote - http://code.msdn.microsoft.com/HVRemote - tool seems to have yielded some positive results, and all tests on the server pass (firewall, permissions, etc), but client-side things are not working. I'm stuck at this step : 5: - Simple query to root\cimv2 WMI namespace FAIL - Simple query failed Cannot perform simple query against root\cimv2 Anyone could help me figure this out? I'm almost giving up and installing XenServer... Thanks

  Read the article

• How do I change Jenkins-ci systemInfo PATH variable

  - by Thomas Schultz

  I have Jenkins setup and it was working but then I updated java and now Jenkins acts like it doesn't know where it is. When I goto my Jenkins server and click manage jenkins-system information under the "Environment Variables" section the PATH variable is wrong. How can I change it? Jenkins is running as root but root's PATH is correct but Jenkins isn't pulling that correctly. Right now Jenkins can't find hg(mercurial) or anything else.

  Read the article

• Saving a modified InfoPath form to its form library

  - by Nathan Lykken

  Within our corporate SharePoint 2007 site, there is a particular form library that contains 10 separate files. 9 of these are either Excel, Word, or PowerPoint files and one of these is an InfoPath 2007 form that serves as a report. After noticing an error within this InfoPath form, I saved this InfoPath form to my local directory and then, within the design mode of InfoPath, I modified this InfoPath form. What is the proper way to save this modified InfoPath form to its form library? Everything that I have tried results in nobody except myself having access to this modified InfoPath form. I can open this InfoPath form without error but when my coworkers try to open this InfoPath form on their machines, they receive this error: “The form cannot be opened because it requires the domain permission level and it currently has restricted permission. To fix this problem, open the form from the location it was published to."

  Read the article

• sftp and public keys

  - by Lizard

  I am trying to sftp into an a server hosted by someone else. To make sure this worked I did the standard sftp [email protected] i was promted with the password and that worked fine. I am setting up a cron script to send a file once a week so have given them our public key which they claim to have added to their authorized_keys file. I now try sftp [email protected] again and I am still prompted for a password, but now the password doesn't work... Connecting to [email protected]... [email protected]'s password: Permission denied, please try again. [email protected]'s password: Permission denied, please try again. [email protected]'s password: Permission denied (publickey,password). Couldn't read packet: Connection reset by peer I did notice however that if I simply pressed enter (no password) it logged me in fine... So here are my questions: Is there a way to check what privatekey/pulbickey pair my sftp connection is using? Is it possible to specify what key pair to use? If all is setup correctly (using correct key pair and added to authorized files) why am I being asked to enter a blank password? Thanks for your help in advance! UPDATE I have just run sftp -vvv [email protected] .... debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-with-mic,publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering public key: /root/.ssh/id_rsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug1: Server accepts key: pkalg ssh-rsa blen 277 debug2: input_userauth_pk_ok: SHA1 fp 45:1b:e7:b6:33:41:1c:bb:0f:e3:c1:0f:1b:b0:d5:e4:28:a3:3f:0e debug3: sign_and_send_pubkey debug1: read PEM private key done: type RSA debug1: Authentications that can continue: publickey,password debug1: Trying private key: /root/.ssh/id_dsa debug3: no such identity: /root/.ssh/id_dsa debug2: we did not send a packet, disable method debug3: authmethod_lookup password debug3: remaining preferred: ,password debug3: authmethod_is_enabled password debug1: Next authentication method: password It seems to suggest that it tries to use the public key... What am I missing?

  Read the article

• SSH broken after hostname change on EC2-hosted Ubuntu

  - by dimadima

  I changed my instance's hostname using the hostname utility and then set it in /etc/hostname so that the new name survives reboot. My main motivation was for differentiating between instances at the prompt using the \h format in PS1. EDIT I also changed permissions on my home directory. I made my home directory group writeable. END EDIT Now I can no longer SSH into the machine. The short of it is the error Permission denied (publickey). Running ssh -v, the more verbose output is: debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Offering RSA public key: /Users/dmitry/.ssh/id_rsa debug1: Authentications that can continue: publickey debug1: Trying private key: /Users/dmitry/.ssh/ec2key.pem debug1: read PEM private key done: type RSA debug1: Authentications that can continue: publickey debug1: No more authentication methods to try. Permission denied (publickey). Should I have done something after changing the hostname? Now I can't get into the instance! :(

  Read the article

• ASP.NET Security Exception when Switch IIS7 to Use UNC Path for Content

  - by Jeremy H.

  I have a Windows Server 2008 R2 box running IIS7.5 with Medium Trust configured for ASP.NET. When I have the website running from local content (e.g.: c:\inetpub\wwwroot) everything works fine. When I change IIS to use a UNC path for the content (e.g.: \\computer\wwwroot) I get the following error: Security Exception Description: The application attempted to perform an operation not allowed by the security policy. To grant this application the required permission please contact your system administrator or change the application's trust level in the configuration file. Exception Details: System.Security.SecurityException: Request for the permission of type 'System.Data.SqlClient.SqlClientPermission, System.Data, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089' failed. I'm trying to figure out why ASP.NET/IIS would allow for the SQL call when using local content but not when using a UNC path. Any ideas what I need to do to use a UNC path from IIS7 properly?

  Read the article

• Sql Server security Issue

  - by MZT

  how to add Sql server user for specific database with backup and restore permission only ??

  Read the article

• Postfix send remotely for X account

  - by Ben Scobie

  I setup Postfix a few days ago to deliver email bound for my host name remotely instead of locally as I want email sent to my remote [email protected] account without trying to be sent locally. However, this causes a problem as it tries to send local bound mail(root) to my remote server as well ([email protected]). I would like E-mail bound for [email protected] to be sent to the remote server(GMail Apps in this case) and everything else sent locally(using the alias file perhaps), is this possible? My current configuration: http://pastebin.com/htwSQB61

  Read the article

• Want to execute an arm compiled executable on adb shell of android

  - by user37977

  I stuck in a problem. I want a chmreader executable file to be used in android application. Now whenever I tried to execute it from adb shell, it gives error "permission denied" Now, whenever I use "su" it just executes the file, but doesn't do anything. And whenever I give the argument as the path of the file to be read, "# su /sdcard/extract_chmLib /sdcard/docs/HArdcore.chm" it shows "su: exec failed for /sdcard/docs/HArdcore.chm Error:Permission denied" where "/sdcard/extract_chmLib" is the executable file and "/sdcard/docs/HArdcore.chm" is the chm file to be read. Can you please help me???

  Read the article

< Previous Page | 146 147 148 149 150 151 152 153 154 155 156 157  | Next Page >