Search Results

Search found 7126 results on 286 pages for 'wireless router'.

Page 151/286 | < Previous Page | 147 148 149 150 151 152 153 154 155 156 157 158  | Next Page >

• How to prevent dial up networking connection window from coming up on Windows 7?

  - by Tom

  I have PPP over Ethernet connection at home, so I have a dial up connection set up which comes up every time when I log in, so I can connect to the net by clicking on it. This works fine, but now I got a router which does the connection automatically, so there is no need for the dial up networking connecting window to come up. Nevertheless it comes up everytime when I log in regardless of the living net connection already established by the router. It does not cause any error I only have to cancel the dialog, but it's a nuisance and I can't find any setting to make it stop. Of course, I could remove the networking connection altogether, but I'd rather keep it, so I don't have to create it again if sometimes I need to connect to the net directly without the router. Is there a way to stop the connection dialog from coming up without removing the networking connection?

  Read the article

• Lagging digital tv over ethernet

  - by Steve

  I have a HD Home Run TV over ethernet device, which connects the aerial to my router, and from there the router connects to my PC over about 15m of 100Mbps ethernet cable. The TV output lags every second. It does not do so for a computer much closer to the router. It is odd to me that the network rate is around 7Mbps on a 100Mbps cable. I am not downloading or streaming anything else on the affected computer. Is this lag caused by the speed of the cable, the length of the cable, or interference on the cable? I am considering swapping the ethernet cable with shielded ethernet cable.

  Read the article

• Routing table change to access Internet over mifi

  - by Randall Blake

  I have two networks at home. One uses a Verizon mifi wireless on 192.168.1.1. The other uses a dlink router on 192.168.0.1. I have one laptop with two nics, one wireless and one not. The wireless nic connects to the mifi. The Ethernet nic connects to the dlink router. It's ip is 192.168.0.2. I also have a laptop with only one nic connected to the dlink on 192.168.0.3. I want to connect laptop 2 to the Internet. Can I do that by adding an entry to the routing table so that destination 0.0.0.0 routes to 192.168.0.2? If I do that, will laptop 1 "know" that it should route traffic from 192.168.0.3 to 192.168.1.1? Thanks for any assistance.

  Read the article

• Mac | Port Forwarding for Remote Desktop

  - by Vaibhav Bajpai

  I have two Mac notebooks at home, I have assigned them static private IPs. I have also set my router to a DynDNS address, which updates everytime my router gets a new public IP. I have enabled Screen Sharing on both notebooks. I can successfully goto my router webpage using the DynDNS address. I understand I need to port-forward to get Screen Sharing to work from outside. Lets assume, notebooks have private IP 192.168.1.2 and 192.168.1.3 I am kind of lost here, would appreciate some help (I need to be able remote desktop to both notebooks)

  Read the article

• Apple file sharing: bind to a specific interface

  - by Cesar

  My customer have an office small office with just a wifi router. He use this router for internet connectivity and file transfer operations between the desktops. Recently the file transfer activity between desktop (all osx based) is increased a lot so he bought a switch (no connected to the router, too far away) for transfer the file over the cable instead over the wifi. Problem: How to bind the file sharing service just to the Ethernet interface and exclude the wifi interface ? (actually the service binds to the wifi automatically and there are no options about the interface binding)

  Read the article

• Iptables NAT logging

  - by Gerard

  I have a box setup as a router using Iptables (masquerade), logging all network traffic. The problem: Connections from LAN IPs to WAN show fine, i.e. SRC=192.168.32.10 - DST=60.242.67.190 but for traffic coming from WAN to LAN it will show the WAN IP as the source, but the routers IP as the destination, then the router - LAN IP. I.e. SRC=60.242.67.190 - DST=192.168.32.199 SRC=192.168.32.199(router) - DST=192.168.32.10 How do I configure it so that it logs the conversations correctly? SRC=192.168.32.10 - DST=60.242.67.190 SRC=60.242.67.190 DST=192.168.32.10 Any help appreciated, cheers

  Read the article

• How to get started setting up IP security cameras

  - by dave

  I have just finished renovating my house. As part of the job, I have cat6 cable run through the house, including two external plugs. All cables terminate in the same location. My rough plan is to plug two IP cameras to monitor the front and rear, run POE from a central router to the two external cameras, plug my PC into the same router and run magic software X. Any machine plugged into the router or wirelessly connection should then be able to get a live feed and alerts based on motion detection. That's the plan, but I'm not sure how possible it is. What hardware to get and what monitoring software to get. Has anyone does something similar? What were your experiences?

  Read the article

• UDP multicast streaming of media content over WIFI

  - by sajad

  I am using vlc to stream media content over wireless network in scenario like this (from content streamer to stream receiver client): The bandwidth of wireless network is 54 Mb/s and UDP stream's required bandwidth is only 4 Mb/s; however there is trouble in receiving media stream and quality of playing specifically in multicast mode; means I can play the stream but it has jitter and does not play smoothly. In uni-cast I can stream up to 5 media streams correctly, but in multicast mode there is problem with streaming just one media! However when I stream from client some multicast streams; the wifi access-point can receive data correctly and I can see the video in "udp streamer" side correctly even when number of multicast streams increases to 9; But as you see I want to stream from streaming server and receive media in client size. Is this a typical problem of streaming real-time contents over wireless networks? Is it necessary to change configurations of my WIFI switch or it is just a software trouble? thank you

  Read the article

• Can a switch consume bandwidth?

  - by aashiq

  I have a network with a router and a switch. At first my ISP's optical fiber is connected with media converter input port. Than Ethernet cable (output port of Media converter) is connected with the switch. Then an output Ethernet cable is connected with our inner Microtik router. Then this router is connected with another LAN switch. From this switch we have got every connection other switch. It is our total network structure. Our bandwidth is 2 Mbps. From the 11th of March our MRTG graph shows high all the time even when my all switch is switched off except LAN switch. That's why our line is breaking up (Voice call). How could be it possible? My all PC's bandwidth is limited but when connected PC with media converter directly then the graph shows normal. That's why I can't blame my ISP.

  Read the article

• Home PBX to answer/take external calls via PSTN

  - by ageis23

  I have a Thomson 585V6 router which has built in voip support. I want to be able to use a softphone to make calls. for example phone my dad's mobile. Any incomming calls to my normal bt number should be taken via my pc as well. What I have done so far: I've wired the pstn port on the router to the telephone jack. The router is connected to my pc. I have installed asterisk on the pc I want to take calls on. The sip client authenticates to the sip server. output from twinkle: Sun 22:46:45 home, registration succeeded (expires = 3600 seconds) how do I take external calls/ answer incoming calls from pstn?

  Read the article

• How to set up my network/bridging using Apple Airport equipment?

  - by John

  I'd like to set up my network like this, and I want to make sure it's possible using the hardware I have. I think it should be... I've got my cable modem in one room. I want to plug it into an Apple Airport Express and create my wireless my wireless network here. The airport express will do the NAT and DHCP. By my TV there are a few things to be networked (Xbox and Tivo). I have an airport extreme here. I'd like to have the airport extreme join the wireless network and share the connection to the ethernet ports. Can anyone provide some assistance on the best way to configure to do this? Thanks!

  Read the article

• Network Drive Via Ethernet Port for Speed?

  - by Yar

  I have a Macbook with Firewire 400 and USB 2.0, so the only way I can get fast external storage is through the Ethernet port. A really fast firewire 800 drive on ANOTHER computer is actually much faster than the built-in drive (according to XBench). So I thought I would try to go one better and buy an ethernet-ready drive. I bought a Seagate GoFlex™ Home Network Storage System, and it seems like the only way to get it to work is to plug it into a router. Can this drive be used without a router (i.e., direct to computer)? Are there any drives that can be plugged directly into the ethernet port for fast access? I don't want the drive on my router: I want it on my computer. Ideally I'd need 7200rpm or faster, too... Update: Just chatted with Seagate and they said that this particular drive will not work that way. Will any others?

  Read the article

• Dial-in VPN Routing issue when on 192.168.x.x network range

  - by Ian

  I'm not an expert on networks but have a small office on the 192.168.x.x. range which is managed by a vigor (2800) router. I have enabled the VPN dial-in option on the router so I can get to the server on 192.168.1.100 which works fine from my macbook when i'm NOT on a local network with that is on the 192.168.x.x range. e.g. works fine when I tether over my Android smartphone but when I try & connect when on my home network, it connects, I can access the router (192.168.1.1) but cannot access 192.168.1.100 - traceroute doesn't hop via 192.168.1.1 I have enabled "send all traffic over VPN connection but again, not joy... Feels like the osx platform isn't routing the traffic out to the vpn endpoint as the destination address is on the local subnet but expect it would be. This work fine on a windows PC on the same home network. Any thoughts on what the issue could be?

  Read the article

• How to make routes on a windows 7 laptop persistent?

  - by askvictor

  I have a number of (windows 7) laptops that normally connect via wireless. We also have a wired network for special purposes. When one of these laptops plugs in to the wired network, at the moment, it makes the wired network the default route. Instead, I would like it to keep the wireless network the default, and route only 10...* through the wired. I can achieve this with: route delete 0.0.0.0 IF 22 route add 10.0.0.0 ... IF 22 (where IF 22 is the wired network interface). But how can I get this to stick? Currently, if the wired network is unplugged then re-plugged, it grabs the default route again. So I want a way of making the wireless network not get the default route, and to make the 10...* network persistent. Is there a hook to run commands after a network connection is established in windows? In linux I would use post-up hooks.

  Read the article

• Uploading with browser makes all other browser tabs and devices disconnect

  - by fabsenet

  Whenever I upload a video to YouTube all other browser tabs behave like there is no connection at all. It even affects my phone and other computers on the network therefor I think it has to do with my router. When the upload is done everything works normally again. I never observed this behavior with any other upload. My router is a Fritz!Box 7390 and my uploading PC is connected through a 1000mb/s switch (wired) to the router. Uploading through another browser does not change anything. I understand that other sites become slow as the network resources are limited, but stopping altogether feels wrong. speed.io measures for my internet connection: 40.894 Kbit/s down, 2.685 Kbit/s up, 29 ms ping, 2.048 con/m connects

  Read the article

• How to route packets from Wi-Fi to Ethernet on OSX?

  - by Alexander Artemenko

  I have a trouble, configuring a home network. Here is how my devices are connected together: Internet     ? Wi-Fi Router ? MacBook     ? iMac ?ethernet cable? Synology NAS I have no ability to plugin NAS right into the Wi-Fi router. The problem is that MacBook does not see NAS, because they are in different networks — I configured Wi-Fi Router to serve 192.168.10.0/24 addresses, and configured iMac's ethernet connection to use 192.168.20/24 network. Is there a way to setup route from MacBook to the NAS?

  Read the article

• HP Media Smart remote access

  - by Coov

  I just purchased this box for home backups for my pc's and mac's. Everything works great accept for the remote access part. I can RD into the machine locally but I can't get to it from outside of my network. I've enabled port forwarding on my router but it doesn't seem to matter. I checked with Qwest and they don't block these ports so I'm at a loss. I do have Vonage in front of my router but I've taken it out and it didn't make a difference. I suspect I've made an error with my router setup. I'm a programmer and I'm playing in the world of the unknown here. I'm lost. Any suggestions?

  Read the article

• How can i access windows XP remote desktop on private IP from internet?

  - by Jennie

  So the machine is behind a DSL router on a private IP so that it can not receive inbound requests. I want to know: Is there anyway to setup the router NAT (i highly doubt it supports one to one port mapping) without disturbing other users on the same router. I have another machine on internet which has public IP on it without any firewall. Can i use this machine as a relay server so that to initiate the connection, the XP machine send an outbound request and this relay server makes my connection through and then i can access my machine on pvt ip without any problem. Please tell??

  Read the article

• Port Forwarding for Remote Desktop

  - by Vaibhav Bajpai

  I have two Mac notebooks at home, I have assigned them static private IPs. I have also set my router to a DynDNS address, which updates everytime my router gets a new public IP. I have enabled Screen Sharing on both notebooks. I can successfully goto my router webpage using the DynDNS address. I understand I need to port-forward to get Screen Sharing to work from outside. Lets assume, notebooks have private IP 192.168.1.2 and 192.168.1.3 I am kind of lost here, would appreciate some help (I need to be able remote desktop to both notebooks)

  Read the article

• switch duplicates packets and forward in two route

  - by sami

  there is a network including a router, two hosts and a switch which connects hosts to router. i have a virtual machine on my system. the network adapter is set to act as bridge. so the virtual machine and real OS are my 2 hosts on different LAN. they use one network card and are connected to a switch. when each of host send a packet to the other one, the switch duplicate the packet and forward it to both router and the other host. how can I solve the duplicate packet problem? Thanks.

  Read the article

• Dynamic to static internal IP address (Snow Leopard server)

  - by bac

  I purchased a new Mac mini server, since my old iMac, which was a server pretty much died. My problem is this. How do I change my internal IP address for my mac mini server to a static address, like 192.168.0.2? Before you guys harp on me, my old server was running Ubuntu Hardy and I only had to map the IP address in the router, which would automatically assign the reserved address through DHCP. Now, I know things are different between the two, but my problem is that the mac is not accepting the assigned IP address or the router just is not assigning. However, every time I have manually changed it on the Mac to an address of my choice, it takes the computer off the Internet. My router is a NetGear WTG624 v2, I believe. I need this to work, so I can utilize Dynamic DNS.

  Read the article

• Remotedesktop to windows 2008 server with 2 nics

  - by The_Mo

  Hi I have 2 NICs on a Windows 2008 R2 Server. nic1 with ip address 192.168.2.1 with gatewaty 192.168.2.254 and nic2 with ip address 10.96.6.253 with no gateway. The windows 2008 server is connected to a router which is connnected to another router so if I want to connect to the windows 2008 server I use 192.168.0.31 because it is forwarded. If I use remote desktop to connect to that machine I use 192.168.0.31 and that works well, but the server has a seccond nic and I want to be able to connect with a remotedesktop to nic2. Any help appreciated! [server windows 2008 r2 192.168.2.1] -- [router 192.168.2.254/192.168.0.31] -- [my computer 192.168.0.13 gateway 192.168.0.254]

  Read the article

• routing weirdness - traceroute 'vanishes' en route

  - by The Journeyman geek

  I'm attempting to set up one of my boxes as a server (again), but i'm having some odd connection issues- the box itself connects fine to the internet, but trying to connect to my external ip address seems to result in the trace getting 'lost' partway. http://pastebin.com/HCQAGbvn - this is a traceroute from another system that's connected to another ISP - starhub is my own one, while i have another system that i have access to on singtel. I'm wondering if my ISP is messing around with routing, or is something very odd going on. As you note, the traceroute dosen't reach me, but if it helps, i use a dd-wrt router. edit: Facepalmishly, turning the firewall on my router on and off fixed it. I don't get why it dropped off at different ip addresses each time, or why the router set it self to block.. everything, or why it affected the ipv6 tunnel as well.

  Read the article

• Access port on machine by connecting to other machine via SSH?

  - by piquadrat

  I have to access my home router's web interface on port 80. Unfortunately, the only way into the network I have at the moment is SSH to another machine on the same network. me ---|---SSH Box----Home Router My Google foo seems to have abandoned me, I couldn't didn't find anything helpful. Any ideas? Thanks! To clarify: I'm not at home right now. I do however have access to one machine on the network (a QNAP NAS) over SSH. I need to access the home router web interface on port 80 from my notebook which is outside of the home network.

  Read the article

• How can I make the NetworkManager work?

  - by Yang Jy

  I am running a version of RHCE6 on my laptop, and lately I've been trying various stuff about network configuration through command line. Last night, I tried removing the NetworkManager using "yum remove NetworkManager" from the system, so that I could have more control of the network through the command line. But the result is, I didn't manage to configure the wireless connection through wpa_supplicant, and I need wireless connection during my travel to another place. So I need the wireless function back as soon as possible. I typed " yum install NetworkManager", some version installed, but I don't get to have an icon on the taskbar, and of course, the network doesn't work. The package I previously removed(about 24MB) was much larger that the one I just installed(about 2MB), so I think some dependencies must be missing. How could I install all these dependencies? Please help!

  Read the article

< Previous Page | 147 148 149 150 151 152 153 154 155 156 157 158  | Next Page >