Search Results

Search found 4586 results on 184 pages for 'supported'.

Page 153/184 | < Previous Page | 149 150 151 152 153 154 155 156 157 158 159 160  | Next Page >

• Adaptec 5805 not recognized after reboot

  - by Rakedko ShotGuns

  After rebooting the system, the controller is not recognized. It only works if the computer is shut down and turned off. I have recently updated the firmware to "Adaptec RAID 5805 Firmware Build 18948". How do I fix the problem? Configuration summary --------------------------- 1. Server name.....................raid_test Adaptec Storage Manager agent...7.31.00 (18856) Adaptec Storage Manager console.7.31.00 (18856) Number of controllers...........1 Operating system................Windows Configuration information for controller 1 ------------------------------------------------------- Type............................Controller Model...........................Adaptec 5805 Controller number...............1 Physical slot...................2 Installed memory size...........512 MB Serial number...................8C4510C6C9E Boot ROM........................5.2-0 (18948) Firmware........................5.2-0 (18948) Device driver...................5.2-0 (16119) Controller status...............Optimal Battery status..................Charging Battery temperature.............Normal Battery charge amount (%).......37 Estimated charge remaining......0 days, 16 hours, 12 minutes Background consistency check....Disabled Copy back.......................Disabled Controller temperature..........Normal (40C / 104F) Default logical drive task priority High Performance mode................Dynamic Number of logical devices.......1 Number of hot-spare drives......0 Number of ready drives..........0 Number of drive(s) assigned to MaxCache cache0 Maximum drives allowed for MaxCache cache8 MaxCache Read Cache Pool Size...0 GB NCQ status......................Enabled Stay awake status...............Disabled Internal drive spinup limit.....0 External drive spinup limit.....0 Phy 0...........................No device attached Phy 1...........................No device attached Phy 2...........................No device attached Phy 3...........................1.50 Gb/s Phy 4...........................No device attached Phy 5...........................No device attached Phy 6...........................No device attached Phy 7...........................No device attached Statistics version..............2.0 SSD Cache size..................0 Pages on fetch list.............0 Fetch list candidates...........0 Candidate replacements..........0 69319...........................31293 Logical device..................0 Logical device name............. RAID level......................Simple volume Data space......................148,916 GB Date created....................09/19/2012 Interface type..................Serial ATA State...........................Optimal Read-cache mode.................Enabled Preferred MaxCache read cache settingEnabled Actual MaxCache read cache setting Disabled Write-cache mode................Enabled (write-back) Write-cache setting.............Enabled (write-back) Partitioned.....................Yes Protected by hot spare..........No Bootable........................Yes Bad stripes.....................No Power Status....................Disabled Power State.....................Active Reduce RPM timer................Never Power off timer.................Never Verify timer....................Never Segment 0.......................Present: controller 1, connector 0, device 0, S/N 9RX3KZMT Overall host IOs................99075 Overall MB......................4411203 DRAM cache hits.................71929 SSD cache hits..................0 Uncached IOs....................29239 Overall disk failures...........0 DRAM cache full hits............71929 DRAM cache fetch / flush wait...0 DRAM cache hybrid reads.........3476 DRAM cache flushes..............-- Read hits.......................0 Write hits......................0 Valid Pages.....................0 Updates on writes...............0 Invalidations by large writes...0 Invalidations by R/W balance....0 Invalidations by replacement....0 Invalidations by other..........0 Page Fetches....................0 0...............................0 73..............................10822 8...............................3 46138...........................4916 27184...........................15226 20875...........................323 16982...........................1771 1563............................5317 1948............................2969 Serial attached SCSI ----------------------- Type............................Disk drive Vendor..........................Unknown Model...........................ST3160815AS Serial Number...................9RX3KZMT Firmware level..................3.AAD Reported channel................0 Reported SCSI device ID.........0 Interface type..................Serial ATA Size............................149,05 GB Negotiated transfer speed.......1.50 Gb/s State...........................Optimal S.M.A.R.T. error................No Write-cache mode................Write back Hardware errors.................0 Medium errors...................0 Parity errors...................0 Link failures...................0 Aborted commands................0 S.M.A.R.T. warnings.............0 Solid-state disk (non-spinning).false MaxCache cache capable..........false MaxCache cache assigned.........false NCQ status......................Enabled Phy 0...........................1.50 Gb/s Power State.....................Full rpm Supported power states..........Full rpm, Powered off 0x01............................113 0x03............................98 0x04............................99 0x05............................100 0x07............................83 0x09............................75 0x0A............................100 0x0C............................99 0xBB............................100 0xBD............................100 0xBE............................61 0xC2............................39 0xC3............................69 0xC5............................100 0xC6............................100 0xC7............................200 0xC8............................100 0xCA............................100 Aborted commands................0 Link failures...................0 Medium errors...................0 Parity errors...................0 Hardware errors.................0 SMART errors....................0 End of the configuration information for controller 1

  Read the article

• Cannot install grub to RAID1 (md0)

  - by Andrew Answer

  I have a RAID1 array on my Ubuntu 12.04 LTS and my /sda HDD has been replaced several days ago. I use this commands to replace: # go to superuser sudo bash # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded" # remove broken disk from RAID mdadm /dev/md0 --fail /dev/sda1 mdadm /dev/md0 --remove /dev/sda1 # see partitions fdisk -l # shutdown computer shutdown now # physically replace old disk by new # start system again # see partitions fdisk -l # copy partitions from sdb to sda sfdisk -d /dev/sdb | sfdisk /dev/sda # recreate id for sda sfdisk --change-id /dev/sda 1 fd # add sda1 to RAID mdadm /dev/md0 --add /dev/sda1 # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded, recovering" # to see status you can use cat /proc/mdstat This is the my mdadm output after sync: /dev/md0: Version : 0.90 Creation Time : Wed Feb 17 16:18:25 2010 Raid Level : raid1 Array Size : 470455360 (448.66 GiB 481.75 GB) Used Dev Size : 470455360 (448.66 GiB 481.75 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Thu Nov 1 15:19:31 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 92e6ff4e:ed3ab4bf:fee5eb6c:d9b9cb11 Events : 0.11049560 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 17 1 active sync /dev/sdb1 After bebuilding completion "fdisk -l" says what I have not valid partition table /dev/md0. This is my fdisk -l output: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00057d19 Device Boot Start End Blocks Id System /dev/sda1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sda2 940910985 976768064 17928540 5 Extended /dev/sda5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000667ca Device Boot Start End Blocks Id System /dev/sdb1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sdb2 940910985 976768064 17928540 5 Extended /dev/sdb5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/md0: 481.7 GB, 481746288640 bytes 2 heads, 4 sectors/track, 117613840 cylinders, total 940910720 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table This is my grub install output: root@answe:~# grub-install /dev/sda /usr/sbin/grub-setup: warn: Attempting to install GRUB to a disk with multiple partition labels or both partition label and filesystem. This is not supported yet.. /usr/sbin/grub-setup: error: embedding is not possible, but this is required for cross-disk install. root@answe:~# grub-install /dev/sdb Installation finished. No error reported. So 1) "update-grub" find only /sda and /sdb Linux, not /md0 2) "dpkg-reconfigure grub-pc" says "GRUB failed to install the following devices /dev/md0" I cannot load my system except from /sdb1 and /sda1, but in DEGRADED mode... Anybody can resolve this issue? I have big headache with this.

  Read the article

• How do you splice out a part of an xvid encoded avi file, with ffmpeg? (no problems with other files

  - by yegor

  Im using the following command, which works for most files, except what seems to be xvid encoded ones /usr/bin/ffmpeg -sameq -i file.avi -ss 00:01:00 -t 00:00:30 -ac 2 -r 25 -copyts output.avi So this should basically splice out 30 seconds of video + audio, starting from 1 minute mark. It does START encoding at the 00:01:00 mark but it goes all the way to the end of the file for some reason, ignoring that I want just 30 seconds. The output looks like this. FFmpeg version git-ecc4bdd, Copyright (c) 2000-2010 the FFmpeg developers built on May 31 2010 04:52:24 with gcc 4.4.3 20100127 (Red Hat 4.4.3-4) configuration: --enable-libx264 --enable-libxvid --enable-libmp3lame --enable-libopenjpeg --enable-libfaac --enable-libvorbis --enable-gpl --enable-nonfree --enable-libxvid --enable-pthreads --enable-libfaad --extra-cflags=-fPIC --enable-postproc --enable-libtheora --enable-libvorbis --enable-shared libavutil 50.15. 2 / 50.15. 2 libavcodec 52.67. 0 / 52.67. 0 libavformat 52.62. 0 / 52.62. 0 libavdevice 52. 2. 0 / 52. 2. 0 libavfilter 1.20. 0 / 1.20. 0 libswscale 0.10. 0 / 0.10. 0 libpostproc 51. 2. 0 / 51. 2. 0 [mpeg4 @ 0x17cf770]Invalid and inefficient vfw-avi packed B frames detected Input #0, avi, from 'file.avi': Metadata: ISFT : VirtualDubMod 1.5.10.2 (build 2540/release) Duration: 00:02:00.00, start: 0.000000, bitrate: 1587 kb/s Stream #0.0: Video: mpeg4, yuv420p, 672x368 [PAR 1:1 DAR 42:23], 25 tbr, 25 tbn, 25 tbc Stream #0.1: Audio: ac3, 48000 Hz, 5.1, s16, 448 kb/s File 'lol6.avi' already exists. Overwrite ? [y/N] y Output #0, avi, to 'lol6.avi': Metadata: ISFT : Lavf52.62.0 Stream #0.0: Video: mpeg4, yuv420p, 672x368 [PAR 1:1 DAR 42:23], q=2-31, 200 kb/s, 25 tbn, 25 tbc Stream #0.1: Audio: mp2, 48000 Hz, 2 channels, s16, 64 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 Press [q] to stop encoding [mpeg4 @ 0x17cf770]Invalid and inefficient vfw-avi packed B frames detected [buffer @ 0x184b610]Buffering several frames is not supported. Please consume all available frames before adding a new one. frame= 1501 fps=104 q=0.0 Lsize= 15612kB time=30.02 bitrate=4259.7kbits/s ts/s video:15303kB audio:235kB global headers:0kB muxing overhead 0.482620% if I convert this file to mp4 for example, and then perform the same action, it works perfectly.

  Read the article

• Nginx Proxying to Multiple IP Addresses for CMS' Website Preview

  - by Matthew Borgman

  First-time poster, so bear with me. I'm relatively new to Nginx, but have managed to figure out what I've needed... until now. Nginx v1.0.15 is proxying to PHP-FPM v.5.3.10, which is listening at http://127.0.0.1:9000. [Knock on wood] everything has been running smoothly in terms of hosting our CMS and many websites. Now, we've developed our CMS and configured Nginx such that each supported website has a preview URL (e.g. http://[WebsiteID].ourcms.com/) where the site can be, you guessed it, previewed in those situations where DNS doesn't yet resolve to our server, etc. Specifically, we use Nginx's Map module (http://wiki.nginx.org/HttpMapModule) and a regular expression in the server_name of the CMS' server{ } block to 1) lookup a website's primary domain name from its preview URL and then 2) forward the request to the "matched" primary domain. The corresponding Nginx configuration: map $host $h { 123.ourcms.com www.example1.com; 456.ourcms.com www.example2.com; 789.ourcms.com www.example3.com; } and server { listen [OurCMSIPAddress]:80; listen [OurCMSIPAddress]:443 ssl; root /var/www/ourcms.com; server_name ~^(.*)\.ourcms\.com$; ssl_certificate /etc/nginx/conf.d/ourcms.com.chained.crt; ssl_certificate_key /etc/nginx/conf.d/ourcms.com.key; location / { proxy_pass http://127.0.0.1/; proxy_set_header Host $h; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; } } (Note: I do realize that the regex in the server_name should be "tighter" for security reasons and match only the format of the website ID (i.e. a UUID in our case).) This configuration works for 99% of our sites... except those that have a dedicated IP address for an installed SSL certificate. A "502 Bad Gateway" is returned for these and I'm unsure as to why. This is how I think the current configuration works for any requests that match the regex (e.g. http://123.ourcms.com/): Nginx looks up the website's primary domain from the mapping, and as a result of the proxy_pass http://127.0.0.1 directive, passes the request back to Nginx itself, which since the proxied request has a hostname corresponding to the website's primary domain name, via the proxy_set_header Host $h directive, Nginx handles the request as if it was as direct request for that hostname. Please correct me if I'm wrong in this understanding. Should I be proxying to those website's dedicated IP addresses? I tried this, but it didn't seem to work? Is there a setting in the Proxy module that I'm missing? Thanks for the help. MB

  Read the article

• How to enjoy DVD on Apple iPad

  - by user44251

  I believe many people spent a sleepless night yesterday waiting for the new Apple Tablet to come, just a few days ago or perhaps longer I noticed fierce debate about it, its name, size, capacity, processor, main features, price etc. And now, they can take a long breath with the new Apple Tablet named iPad officially released on 28, January, 2010 (Beijing Time). But I know a new battle just begins. iPad, sounds somewhat like iPod and it really shares some similarities in terms of shape like smart, light and portable. It has a 9.7-inch, LED-backlit, IPS display with a remarkable precise Multi-Touch screen. And yet, at just 1.5 lbs and 0.5 inches thin, it's easy to carry and use everywhere. It can greatly facilitates your experience with the web, emails, photos and videos. Right now, it can run almost 140.000 of the apps on the Apple store. It can even run the apps you have downloaded for your iPhone or iPod touch. But so far, I haven't seen any possibility that it can work with DVD, probability there is no built-in DVD-ROM or DVD player which can play DVD directly. As Apple iPad states, the video formats supported are MPEG-4 (MP4, M4V), H.264, MOV etc and audio formats accepted are AAC, Proteceted AAC, MP3, AIFF and WAV etc, those are formats that are commonly used with iMac. This could really a hard nut to crack if you want to watch your favourite DVD on this magic Apple iPad. But don't worry, there is still way out, you just need a few steps for ripping and importing DVD movies to Apple iPad with a simple application DVD to iPad converter What's on DVD to iPad Converter for Mac DVD to iPad converter for Mac is a powerful and professional application designed for the newly released Apple iPad which can rip, convert your DVD contents to Apple iPad compatible MPEG-4 (MP4, M4V), H.264, MOV etc, and other popular file formats like AVI, WMV, MPG, MKV, VOB, 3GP, FLV etc can also be converted so that you can put on your portable devices like iPod, iPhone, iRiver, BlackBerry etc. Besides, it can also extract audio from DVD videos and save as MP3, AIFF, AAC, WAV etc. Mac DVD to iPad converter has also been enhanced that can run both on PowerPC and Intel (Snow Leopard included). It can offer versatile editing features which allows you to make your own DVD videos. For example, you can cut your DVD to whatever length you like by Trim, crop off unwanted parts from DVD clips by Crop, add special effect like Gray, Emboss and Old film to make your videos more artistic. Besides, its built-in merging feature and batch mode allows you to join several DVD clips into a single one and do batch conversion. And more features can be expected if you afford a few minutes to try.

  Read the article

• Internet Explorer cannot display page from apache with single SSL virtual host

  - by P.scheit

  I have a question that has come up somehow in different questions but I still can't find the solution, yet. My problem is that I'm hosting a site on apache 2.4 on debian with SSL and Internet Explorer 7 on windows xp shows Internet Explorer cannot display the webpage I have only ONE virtual host that uses ssl, but DIFFERENT virtual hosts that use http. Here is my config for the site with SSL enabled (etc/sites-avaible/default-ssl is NOT linked) <Virtualhost xx.yyy.86.193:443> ServerName www.my-certified-domain.de ServerAlias my-certified-domain.de DocumentRoot "/var/local/www/my-certified-domain.de/current/www" Alias /files "/var/local/www/my-certified-domain.de/current/files" CustomLog /var/log/apache2/access.my-certified-domain.de.log combined <Directory "/var/local/www/my-certified-domain.de/current/www"> AllowOverride All </Directory> SSLEngine on SSLCertificateFile /etc/ssl/certs/www.my-certified-domain.de.crt SSLCertificateKeyFile /etc/ssl/private/www.my-certified-domain.de.key SSLCipherSuite HIGH:MEDIUM:!aNULL:+SHA1:+MD5:+HIGH:+MEDIUM SSLCertificateChainFile /etc/apache2/ssl.crt/www.my-certified-domain.de.ca BrowserMatch "MSIE [2-8]" nokeepalive downgrade-1.0 force-response-1.0 </VirtualHost> <VirtualHost *:80> ServerName www.my-certified-domain.de ServerAlias my-certified-domain.de CustomLog /var/log/apache2/access.my-certified-domain.de.log combined Redirect permanent / https://www.my-certified-domain.de/ </VirtualHost> my ports.conf looks like this: NameVirtualHost *:80 Listen 80 <IfModule mod_ssl.c> # If you add NameVirtualHost *:443 here, you will also have to change # the VirtualHost statement in /etc/apache2/sites-available/default-ssl # to <VirtualHost *:443> # Server Name Indication for SSL named virtual hosts is currently not # supported by MSIE on Windows XP. Listen 443 </IfModule> <IfModule mod_gnutls.c> Listen 443 </IfModule> the output from apache2ctl -S is like this: xx.yyy.86.193:443 www.my-certified-domain.de (/etc/apache2/sites-enabled/020-my-certified-domain.de:1) wildcard NameVirtualHosts and _default_ servers: *:80 is a NameVirtualHost default server phpmyadmin.my-certified-domain.de (/etc/apache2/conf.d/phpmyadmin.conf:3) port 80 namevhost phpmyadmin.my-certified-domain.de (/etc/apache2/conf.d/phpmyadmin.conf:3) port 80 namevhost staging.my-certified-domain.de (/etc/apache2/sites-enabled/010-staging.my-certified-domain.de:1) port 80 namevhost testing.my-certified-domain.de (/etc/apache2/sites-enabled/015-testing.my-certified-domain.de:1) port 80 namevhost www.my-certified-domain.de (/etc/apache2/sites-enabled/020-my-certified-domain.de:31) I included the solution for this question: Internet explorer cannot display the page, other browsers can, possibly htaccess / server error And I understand the answer from this question: How to setup Apache NameVirtualHost on SSL? In fakt: I only have one ssl certificate for the domain. And I only want to run ONE virtual host with ssl. So I just want to use the one ip for the ssl virtual host. But still (after rebooting / restarting / testing) internet explorer will still not show the page. When I intepret the apachectl -S as well, I already have only one SSL host and this should response to the initial SSH handshake, shouldn't it? What is wrong in this setup? Thank you so much Philipp

  Read the article

• Do these 3 crashes have something in common?

  - by David U

  I'm running OS X 10.6.8 on a Mac Mini. I tried to install 3 applications today and all 3 installations failed. I am wondering if the failures have something in common. First I installed GraphViz. The installation succeeded, but when I try to open any .dot file, I get a dialog that says GraphViz has quit unexpectedly. Next I installed Doxygen. It installed, but when I try to launch it I get a dialog that tells me Doxywizard quit unexpectedly. After some googling I thought perhaps my system lacked QT, and that was the problem. I downloaded the Qt 4.8.4 packages and installed them. But when I try to launch qtdemo.app, or any of the other apps that came with the qt installation, I get a dialog that says I can't open the app because it's not supported on this type of Mac. I have crash logs from GraphViz and Doxygen. They're long and I think it unnecessary to post them unless they would help someone determine my problem. Thanks Excerpt from System Log, added later: 12/13/12 5:26:21 PM [0x0-0x4f04f].com.apple.DiskImageMounter[1322] 2012-12-13 17:26:21.927 DiskImages UI Agent[1333:903] *** -[NSMachPort handlePortMessage:]: dropping incoming DO message because the connection or ports are invalid 12/13/12 5:30:31 PM [0x0-0x1a01a].org.mozilla.firefox[824] [ConvConfHandler] isPreferred contentType: application/x-apple-diskimage 12/13/12 5:35:32 PM DiskImages UI Agent[1384] *** -[NSMachPort handlePortMessage:]: dropping incoming DO message because the connection or ports are invalid 12/13/12 5:35:32 PM [0x0-0x5a05a].com.apple.DiskImageMounter[1376] 2012-12-13 17:35:32.988 DiskImages UI Agent[1384:903] *** -[NSMachPort handlePortMessage:]: dropping incoming DO message because the connection or ports are invalid 12/13/12 6:07:33 PM DisplayLinkUserAgent[772] (00116500.405)-[DLDistributedNotificationCenter stream:handleEvent:] reconnected. 12/13/12 6:07:33 PM [0x0-0x6c06c].backupd-helper[1446] Not starting Time Machine backup after wake - less than 60 minutes since last backup completed. 12/13/12 6:08:43 PM Installer[1403] PackageKit: *** Missing bundle identifier: /Library/Receipts/BrotherPPD.pkg 12/13/12 6:08:48 PM Installer[1403] PackageKit: *** Missing bundle identifier: /Library/Receipts/NeoOffice-2.2.3-Intel.pkg 12/13/12 6:08:48 PM Installer[1403] PackageKit: *** Missing bundle identifier: /Library/Receipts/NeoOffice-2.2.3-Patch-2-Intel.pkg 12/13/12 6:08:48 PM Installer[1403] PackageKit: *** Missing bundle identifier: /Library/Receipts/NeoOffice-2.2.5-Intel.pkg 12/13/12 6:08:48 PM Installer[1403] PackageKit: *** Missing bundle identifier: /Library/Receipts/NeoOffice.pkg 12/13/12 6:08:48 PM Installer[1403] PackageKit: *** Missing bundle identifier: /Library/Receipts/PIXMA iP6000D 290.pkg 12/13/12 6:14:39 PM com.apple.launchd.peruser.501[359] ([0x0-0x70070].com.att.graphviz[2047]) Job appears to have crashed: Bus error 12/13/12 6:14:41 PM ReportCrash[2056] Saved crash report for Graphviz[2047] version 2.28 (2.28.0) to /Users/duzzell/Library/Logs/DiagnosticReports/Graphviz_2012-12-13-181441_Amun.crash 12/13/12 6:15:19 PM com.apple.launchd.peruser.501[359] ([0x0-0x74074].org.doxygen[2070]) Job appears to have crashed: Bus error 12/13/12 6:15:19 PM ReportCrash[2056] Saved crash report for Doxywizard[2070] version 1.8.2 (???) to /Users/duzzell/Library/Logs/DiagnosticReports/Doxywizard_2012-12-13-181519_Amun.crash

  Read the article

• How to conform to update-rc.d with LSB standard?

  - by user34881

  This is a migrated question from stackoverflow, as I was told, this is the place for it to be. http://stackoverflow.com/questions/2263567/how-to-conform-to-update-rc-d-with-lsb-standard I have set up a simple script to back up some directories. While I haven't had any problems setting up the functionality, I'm stuck with adding the script to rcX.d dir's using update-rc.d. My script: #! /bin/sh ### BEGIN INIT INFO # Provides: backup # Required-Start: backup # Required-Stop: # Should-Stop: # Default-Start: 0 6 # Default-Stop: # Description: Backs up some dirs ### END INIT INFO check_mounted() { # Check if HD is mounted } do_backup() { if check_mounted; then # Some rsync statements. fi } case "$1" in start) do_backup ;; restart|reload|force-reload) echo "Error: argument '$1' not supported" >&2 exit 3 ;; stop|"") # No-op ;; *) echo "Usage: backup [start]" >&2 exit 3 ;; esac : Using update-rc.d backup start 10 0 6 . I get the following warnings and errors: update-rc.d: warning: backup start runlevel arguments (none) do not match LSB Default-Start values (0 6) update-rc.d: warning: backup stop runlevel arguments (0 6.) do not match LSB Default-Stop values (none) update-rc.d: error: start|stop arguments not terminated by "." The syntax I try to use is the following: update-rc.d [-n] <basename> start|stop NN runlvl [runlvl] [...] . Google wasn't that helpful at finding a solution. How can I correctly set up a script and add it via update-rc.d? I'm using Ubuntu 9.10. UPDATE Using update-rc.d backup start 10 0 6 . stop 10 0 . the error disappears. The warnings about default values persists: update-rc.d: warning: backup start runlevel arguments (none) do not match LSB Default-Start values (0 6) update-rc.d: warning: backup stop runlevel arguments (0 6 0 6) do not match LSB Default-Stop values (none) It even is added to the appropiate rcX-dirs but it still does not get executed...

  Read the article

• Nvidia Drivers on Debian / Lenny (Stable) -> Installation successful -> Monitors gets black

  - by David

  I have successfully installed the proprietary drivers for my nvidia (geforce 7300 gt) graphics card on debian/lenny. I know its not the best way to chose for driver installation ( see this link: http://wiki.debian.org/NvidiaGraphicsDrivers#non-freedrivers ). but the two ways seem to be possible for me (nvidia-kernel module compilation). Now the problem is that the monitors gets black, the power light starts blinking after i launch the x-server. Have a short look a the logs (output truncated from /var/log/Xorg.0.log): (II) Setting vga for screen 0. (**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32 (==) NVIDIA(0): RGB weight 888 (==) NVIDIA(0): Default visual is TrueColor (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0) (**) Jul 28 17:10:11 NVIDIA(0): Enabling RENDER acceleration (II) Jul 28 17:10:11 NVIDIA(0): Support for GLX with the Damage and Composite X extensions is (II) Jul 28 17:10:11 NVIDIA(0): enabled. (II) Jul 28 17:10:11 NVIDIA(0): NVIDIA GPU GeForce 7300 GT (G73) at PCI:1:0:0 (GPU-0) (--) Jul 28 17:10:11 NVIDIA(0): Memory: 262144 kBytes (--) Jul 28 17:10:11 NVIDIA(0): VideoBIOS: 05.73.22.25.00 (II) Jul 28 17:10:11 NVIDIA(0): Detected PCI Express Link width: 16X (--) Jul 28 17:10:11 NVIDIA(0): Interlaced video modes are supported on this GPU (--) Jul 28 17:10:11 NVIDIA(0): Connected display device(s) on GeForce 7300 GT at PCI:1:0:0: (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (CRT-0) (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (DFP-0) (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (CRT-0): 400.0 MHz maximum pixel clock (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (DFP-0): 165.0 MHz maximum pixel clock (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (DFP-0): Internal Single Link TMDS (II) Jul 28 17:10:11 NVIDIA(0): Assigned Display Device: CRT-0 (==) Jul 28 17:10:11 NVIDIA(0): (==) Jul 28 17:10:11 NVIDIA(0): No modes were requested; the default mode "nvidia-auto-select" (==) Jul 28 17:10:11 NVIDIA(0): will be used as the requested mode. (==) Jul 28 17:10:11 NVIDIA(0): (II) Jul 28 17:10:11 NVIDIA(0): Validated modes: (II) Jul 28 17:10:11 NVIDIA(0): "nvidia-auto-select" (II) Jul 28 17:10:11 NVIDIA(0): Virtual screen size determined to be 1280 x 1024 (--) Jul 28 17:10:11 NVIDIA(0): DPI set to (85, 86); computed from "UseEdidDpi" X config (--) Jul 28 17:10:11 NVIDIA(0): option (==) Jul 28 17:10:11 NVIDIA(0): Enabling 32-bit ARGB GLX visuals. (--) Depth 24 pixmap format is 32 bpp Here is the complete /etc/X11/xorg.conf file as generated by nvidia-xconfig: # nvidia-xconfig: X configuration file generated by nvidia-xconfig # nvidia-xconfig: version 256.35 (buildmeister@builder101) Wed Jun 16 19:25:59 PDT 2010 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" EndSection Section "Files" EndSection Section "Module" Load "dbe" Load "extmod" Load "type1" Load "freetype" Load "glx" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "Unknown" Hor

  Read the article

• What the best way to achieve RPO of zero and lowest possible RTO (less than 15 minutes) with SQL 2008 R2?

  - by Adrian Hope-Bailie

  We are running a payments (EFT transaction processing) application which is processing high volumes of transactions 24/7 and are currently investigating a better way of doing DB replication to our disaster recovery site. Our current and previous strategies have included using both DoubleTake and Redgate to replicate data to a warm stand-by. DoubleTake is the supported solution from the payments software vendor however their (DoubleTake's) support in South Africa is very poor. We had a few issues and simply couldn't ever resolve them so we had to give up on DoubleTake. We have been using Redgate to manually read the data from the primary site (via queries) and write to the DR site but this is: A bad solution Getting the software vendor hot and bothered whenever we have support issues as it has a tendency to interfere with the payment application which is very DB intensive. We recently upgraded the whole system to run on SQL 2008 R2 Enterprise which means we should probably be looking at using some of the built-in replication features. The server has 2 fairly large databases with a mixture of tables containing highly volatile transactional data and pretty static configuration data. Replication would be done over a WAN link to a separate physical site and needs to achieve the following objectives. RPO: Zero loss - This is transactional data with financial impact so we can't lose anything. RTO: Tending to zero - The business depends on our ability to process transactions every minute we are down we are losing money I have looked at a few of the other questions/answers but none meet our case exactly: SQL Server 2008 failover strategy - Log shipping or replication? How to achieve the following RTO & RPO with logshipping only using SQL Server? What is the best of two approaches to achieve DB Replication? My current thinking is that we should use mirroring but I am concerned that for RPO:0 we will need to do delayed commits and this could impact the performance of the primary DB which is not an option. Our current DR process is to: Stop incoming traffic to the primary site and allow all in-flight transaction to complete. Allow the replication to DR to complete. Change network routing to route to DR site. Start all applications and services on the secondary site (Ideally we can change this to a warmer stand-by whereby the applications are already running but not processing any transactions). In other words the DR database needs to, as quickly as possible, catch up with primary and be ready for processing as the new primary. We would then need to be able to reverse this when we are ready to switch back. Is there a better option than mirroring (should we be doing log-shipping too) and can anyone suggest other considerations that we should keep in mind?

  Read the article

• Ubuntu stopped recognizing my iPod

  - by flashnode

  Rythmbox on Ubuntu 10.10 used to recognize my 3rd gen Nano and transfer mp3s. Now I plug it in and Ubuntu doesn't pop-up that box that asks what you want to do anymore. It is only recognized if I reboot and the thing is plugged in. Here is the output to 'lsusb -v -s bus:device' Bus 001 Device 008: ID 05ac:1262 Apple, Inc. iPod Nano 3.Gen Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x05ac Apple, Inc. idProduct 0x1262 iPod Nano 3.Gen bcdDevice 0.01 iManufacturer 1 Apple Inc. iProduct 2 iPod iSerial 3 000A27001A670128 bNumConfigurations 2 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 32 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xc0 Self Powered MaxPower 500mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 8 Mass Storage bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk (Zip) iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 149 bNumInterfaces 3 bConfigurationValue 2 iConfiguration 4 iPod USB Interface bmAttributes 0xc0 Self Powered MaxPower 500mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 0 bInterfaceClass 1 Audio bInterfaceSubClass 1 Control Device bInterfaceProtocol 0 iInterface 0 AudioControl Interface Descriptor: bLength 9 bDescriptorType 36 bDescriptorSubtype 1 (HEADER) bcdADC 1.00 wTotalLength 30 bInCollection 1 baInterfaceNr( 0) 1 AudioControl Interface Descriptor: bLength 12 bDescriptorType 36 bDescriptorSubtype 2 (INPUT_TERMINAL) bTerminalID 1 wTerminalType 0x0201 Microphone bAssocTerminal 2 bNrChannels 2 wChannelConfig 0x0003 Left Front (L) Right Front (R) iChannelNames 0 iTerminal 0 AudioControl Interface Descriptor: bLength 9 bDescriptorType 36 bDescriptorSubtype 3 (OUTPUT_TERMINAL) bTerminalID 2 wTerminalType 0x0101 USB Streaming bAssocTerminal 1 bSourceID 1 iTerminal 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 0 bNumEndpoints 0 bInterfaceClass 1 Audio bInterfaceSubClass 2 Streaming bInterfaceProtocol 0 iInterface 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 1 bNumEndpoints 1 bInterfaceClass 1 Audio bInterfaceSubClass 2 Streaming bInterfaceProtocol 0 iInterface 0 AudioStreaming Interface Descriptor: bLength 7 bDescriptorType 36 bDescriptorSubtype 1 (AS_GENERAL) bTerminalLink 2 bDelay 1 frames wFormatTag 1 PCM AudioStreaming Interface Descriptor: bLength 35 bDescriptorType 36 bDescriptorSubtype 2 (FORMAT_TYPE) bFormatType 1 (FORMAT_TYPE_I) bNrChannels 2 bSubframeSize 2 bBitResolution 16 bSamFreqType 9 Discrete tSamFreq[ 0] 8000 tSamFreq[ 1] 11025 tSamFreq[ 2] 12000 tSamFreq[ 3] 16000 tSamFreq[ 4] 22050 tSamFreq[ 5] 24000 tSamFreq[ 6] 32000 tSamFreq[ 7] 44100 tSamFreq[ 8] 48000 Endpoint Descriptor: bLength 9 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 1 Transfer Type Isochronous Synch Type None Usage Type Data wMaxPacketSize 0x00c0 1x 192 bytes bInterval 4 bRefresh 0 bSynchAddress 0 AudioControl Endpoint Descriptor: bLength 7 bDescriptorType 37 bDescriptorSubtype 1 (EP_GENERAL) bmAttributes 0x01 Sampling Frequency bLockDelayUnits 0 Undefined wLockDelay 0 Undefined Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 2 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 3 Human Interface Device bInterfaceSubClass 0 No Subclass bInterfaceProtocol 0 None iInterface 0 HID Device Descriptor: bLength 9 bDescriptorType 33 bcdHID 1.01 bCountryCode 0 Not supported bNumDescriptors 1 bDescriptorType 34 Report wDescriptorLength 208 Report Descriptors: ** UNAVAILABLE ** Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 1 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 2 Device Status: 0x0000 (Bus Powered) This ubuntu forum told me to check the automount settings under /apps/nautilus/preferences/media_automount_open in gconf-editor. And I did that. Any clues?

  Read the article

• Windows Server 2008 R2 Firewall - Interface specific rules

  - by Mehmet Ergut

  I'm trying to define per interface rules, much like it was in Server 2003. We will be replacing our old 2003 server with a new 2008 R2 server. The server runs IIS and SQL Server. It's a dedicated server at the hosting company. We use a OpenVPN connection from the office to access SQL server, RDesktop, FTP and other administrative services. Only http and ssh is listening on the public interface. On the old server running 2003, I was able to define global rules for http and ssh, and allow other services only on the vpn interface. I can't find a way to do the same on 2008 R2. I understand that there is the Network Location Awareness service, firewall rules are applied according to the current network location. But I don't understand the purpose of this on a server. The only close solution I found is to set the scope on the firewall rule and restrict remote ip addresses to the private subnet of the office. But the ports will still be listening on the public interface. So how can I restrict a firewall rule to the connections coming from the vpn interface ? A note on this page states that scoping a rule to an interface does not exist anymore: In earlier versions of Windows, many of these command accepted a parameter called interface. This parameter is not supported in the firewall context in Windows Vista or later versions of Windows. I can't believe that they simply decided to remove a core firewall functionality that every firewall has. There must be a way to restrict a rule to an interface. Any ideas ? I'm still unable to find an adequate solution to my problem. So for now, my workaround is this: Administrative services listen on VPN IP address Firewall rules restrict the scope to the local IP address of VPN Public services listen on all interfaces, no scope restriction on firewall rules This is not optimal, if I change the IP address of the VPN, I need to edit the firewall rules too. It won't be the case if the rules were bound to the interface.

  Read the article

• How do you splice out a part of an xvid encoded avi file, with ffmpeg? (no problems with other files)

  - by user11955

  Im using the following command, which works for most files, except what seems to be xvid encoded ones /usr/bin/ffmpeg -sameq -i file.avi -ss 00:01:00 -t 00:00:30 -ac 2 -r 25 -copyts output.avi So this should basically splice out 30 seconds of video + audio, starting from 1 minute mark. It does START encoding at the 00:01:00 mark but it goes all the way to the end of the file for some reason, ignoring that I want just 30 seconds. The output looks like this. FFmpeg version git-ecc4bdd, Copyright (c) 2000-2010 the FFmpeg developers built on May 31 2010 04:52:24 with gcc 4.4.3 20100127 (Red Hat 4.4.3-4) configuration: --enable-libx264 --enable-libxvid --enable-libmp3lame --enable-libopenjpeg --enable-libfaac --enable-libvorbis --enable-gpl --enable-nonfree --enable-libxvid --enable-pthreads --enable-libfaad --extra-cflags=-fPIC --enable-postproc --enable-libtheora --enable-libvorbis --enable-shared libavutil 50.15. 2 / 50.15. 2 libavcodec 52.67. 0 / 52.67. 0 libavformat 52.62. 0 / 52.62. 0 libavdevice 52. 2. 0 / 52. 2. 0 libavfilter 1.20. 0 / 1.20. 0 libswscale 0.10. 0 / 0.10. 0 libpostproc 51. 2. 0 / 51. 2. 0 [mpeg4 @ 0x17cf770]Invalid and inefficient vfw-avi packed B frames detected Input #0, avi, from 'file.avi': Metadata: ISFT : VirtualDubMod 1.5.10.2 (build 2540/release) Duration: 00:02:00.00, start: 0.000000, bitrate: 1587 kb/s Stream #0.0: Video: mpeg4, yuv420p, 672x368 [PAR 1:1 DAR 42:23], 25 tbr, 25 tbn, 25 tbc Stream #0.1: Audio: ac3, 48000 Hz, 5.1, s16, 448 kb/s File 'lol6.avi' already exists. Overwrite ? [y/N] y Output #0, avi, to 'lol6.avi': Metadata: ISFT : Lavf52.62.0 Stream #0.0: Video: mpeg4, yuv420p, 672x368 [PAR 1:1 DAR 42:23], q=2-31, 200 kb/s, 25 tbn, 25 tbc Stream #0.1: Audio: mp2, 48000 Hz, 2 channels, s16, 64 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 Press [q] to stop encoding [mpeg4 @ 0x17cf770]Invalid and inefficient vfw-avi packed B frames detected [buffer @ 0x184b610]Buffering several frames is not supported. Please consume all available frames before adding a new one. frame= 1501 fps=104 q=0.0 Lsize= 15612kB time=30.02 bitrate=4259.7kbits/s ts/s video:15303kB audio:235kB global headers:0kB muxing overhead 0.482620% if I convert this file to mp4 for example, and then perform the same action, it works perfectly.

  Read the article

• Network Services disabled (not starting) on Windows XP

  - by Rickesh John

  I am currently running Windows XP Service Pack 3 on my system. But today, when I failed to connect to the internet, via a LAN cable, I realized that almost all of the vital network services had stopped functioning. Any attempts to start it through services.msc gives me the following message: Could not start the DNS Client Service on Local Computer Error 1068: The dependency service group failed to start All my software or services that are related to networking have stopped functioning, for example, Windows Firewall is turned off permanently, so is my Avast Anti-Virus' service of Real Time Shields and Web Shield. When I insert the LAN wire into my laptop, it registers itself, but this is what I get when I do a ping localhost C:>ping localhost Unable to contact IP driver, error code 2 Moveover, with ipconfig I get this : Windows IP Configuration An internal error occurred: The request is not supported. Please contact Microsoft Product Support Services for further help. Additional Information: Unable to query host name On some further poking around, I saw that none of the "NETWORK SERVICE" process in task manager, except svchost.exe were running. Also, when I first opened the task manager, I saw some 20 processes running with username column empty for most of them. With some search in Google, I found out that these services were important, DHCP DNS Net logon Network connection Network location Awareness TCP/IP Net BIOS Helper none of them, except Network Connections are working, they do not start. The event viewer of my system shows a bunch of 7000 and 7001 event errors. I have tried re installing the network driver, booting in safe mode with networking and tried to enable those services mentioned above. I had disabled System Restore some time back, so I have no restore points for my system. I tried a lot of things from Google searches but none of them worked. Also, with such a long list of issue, I am a little confused as to what should I search on the internet. :( One more thing I would like to mention, previous morning, my anti-virus Avast detected a RootKit buried deep in my system folders. It was removed, but maybe this was a problem caused by the root kit. I did run a boot-time scan but no viruses were found. Please please please advice. Is formatting and re-installation of Windows my only option?

  Read the article

• iTunes and Hulu Playback Choppy and Slow?

  - by Bart Silverstrim

  Specs: Windows XP, latest updates 1.7 ghz Pentium 4 1 gig ram DirectX 9.0c NVIDIA GeForce FX 5200 with 256 meg RAM OpenGL 2.1 The story: Okay, I had an older system laying around that I figured I would try turning into a mini-media system to connect to our TV. I put together a lot of older parts, got it into working order, etc. and hooked it up and voila'...slower, but usable system that displayed to the TV. It could run some things decently. I put in iTunes, it played video okay. Not great, but okay. Played Hulu and since we have a 1Mb download rate, the minimum for their site, there were some choppy moments when watching their shows, but I found that (sadly) changing resolution to 800x600 seemed to help with the issue when running full screen. I downloaded the application called Boxee and installed it. It wouldn't run; apparently the video card in the system supported OpenGL 1.2, and needed at least 1.4. I bought a cheap card, the 5200, with four times the memory in it and support for OpenGL 2.1. Installed, everything seemed fine. iTunes seemed to run fine, the video driver (PNY video card) came with OpenGL 2.1, and Boxee finally ran. I then upgraded to the latest drivers for the video card and ran the DirectX updater from MS. After that, the OpenGL Extension Viewer wouldn't run. It just stayed as an icon in the task bar. Also, any and all videos in iTunes stuttered and went out of sync horribly. Unwatchable. I tried watching Hulu video in Boxee, and it displayed video like it was a series of stills in a very bad powerpoint. Playing straightforward audio-only came through fine, no stutters no hiccups. I tried system restore to roll back updates to pre-directX updates (I thought that seemed to be the time that triggered the weird behavior), no joy. I tried uninstalling and reinstalling the video drivers. I installed updated audio drivers (ensoniq audiopci), nothing helped. I finally wiped the drive last night and tried reinstalling everything and restoring my iTunes content via an import from a backup. Fresh install, no updater on the video card or directx. the problem was still there although I haven't tested Hulu, the iTunes player is still stuttering like crazy if I play video, fine if I play audio. I know the processor isn't high in heft, but with one gig of RAM and the fact that it seemed to do okay before I thought that the problem must be software related. Has anyone else run into this sort of issue and have a solution other than "buy a new computer"? What specs seem to work with video at the low end for you? Right now the system is of little use other than keeping my music library and iTunes apps synced with my iPod.

  Read the article

• cd Command Linux and Mystery Flags

  - by Jason R. Mick

  Platform: CentOS 6.2 Shell:tcsh I'm playing around with cd for a BASH script, and noticed the wondrous cd - option, but was left with many questions... Why the cd -? Isn't this redundant with cd ..? EDIT [As FatalError points out, these two commands don't do the same things... so the answer is "no"] Can you delve farther back into your history with - flag, a la in a browser? e.g. When I type cd -, it takes me to my previous directory, but then if I enter that command again, it takes me to the directory I just came from, creating a sort of loop. Is a shorthand for going back multiple levels supported?EDITI realize I can go back with cd .., but was hoping this could be a gateway to a less verbose deep back, e.g. cd -3 vs. cd ../../../ ... hopefully that clarifies what I'm asking....EDIT2As to the current feedback, while .. is a special directory, I don't see a reason why the built-in cd to the terminal couldn't use a shorthand for ../../ ... ../ e.g. cd ..5 or why the built-in also couldn't have a history (a la auto pushd/popd) that could be turned on and used like cd -3. I get that this could be somewhat of security/privacy risk, but I don't see how it's any worst than storing a command history, which most shells/terminals do. The manpage for cd, accessible via man cd and help cd (it's the same for either command), only lists -L and -P flags. However when I type in cd --help it outputs Usage: cd [-plvn][-|<dir>].. Am I right in assuming the other flags and the - (back) option are nonstandard? What are the -n and -v flags for? Both seem to take me back to my home directory, that's all I've been able to figure out via experimentation. A quick read on web resources [1][2] offered just the same sort of info that the man page did and didn't answer my questions. Note: The second Linux-centric resource above claimed cd only had two options (obviously not true in current CentOS) hence my assumption that this functionality could be non-standard.

  Read the article

• General guidelines / workflow to convert or transfer video "professionally"?

  - by cloneman

  I'm an IT "professional" who sometimes has to deal with small video conversion / video cutting projects, and I'd like to learn "the right way" to do this. Every time I search Google, there's always a disaster for weird, low-maturity trialware, or random forums threads from 3-4 years ago indicating various antiquated method to do it. The big question is the following: What are the "general" guidelines and tools to transcode video into some efficient (lossless?) intermediary, for editing purposes, for the purpose of eventually re-encoding it after? It seems to me like even the simplest of formats and tasks are a disaster of endless trial & error, or expertise only known by hardened experts who have a swiss army kife of weird conversion tools that they use, almost as if mounting an attack against the project. Here are a few cases in point: Simple VOB files extracted from DVD footage can't be imported into Adobe Premiere directly. Virtualdub is an old software people keep recommending but doesn't seem to support newer formats. I don't even know how to tell with certainty which codecs a video has, and weather the image is interlaced or not, and what resolution and codecs I'm dealing with. Problems: Choosing a wrong interlace option which diminishes quality Choosing a wrong pixel aspect ratio (stretches the image) Choosing a wrong "project type" in Premiere causing footage to require scaling Being forced to use some weird program that will have any number of negative effects What I'm looking for: Books or "Real knowledge" on format conversions, recognized tools, etc. that aren't some random forum guides on how to deal with video formats. Workflow guidelines on identifying a format going from one format to another without problems as mentioned above. Documentation on what programs like Adobe Premiere can and can't do with regards to formats, so that I don't use a wrench as a hammer. TL;DR How should you convert or "prepare" a video file to ensure it will be supported by Premiere for editing? Is premiere a suitable program to handle cropping, encoding, or should other tools be used for this, when making a video montage from a variety of source formats? What are some good books to read that specifically deal with converting videos that use any number of codecs?

  Read the article

• MySQL won't start, reinstall fails on Ubuntu 12.04

  - by Evils

  My problem started yesterday night when I tried to change the my.cnf config on my ubuntu 12.04 x64 System. I simply tried to changed the bind-address parameter from 127.0.0.1 to 0.0.0.0. A simple restart after a reboot gave this error: stop: Unknown instance: start: Job failed to start I tried to start mysql then by using 'mysqld' which outputs this: 130701 11:05:59 [Note] Plugin 'FEDERATED' is disabled. mysqld: Table 'mysql.plugin' doesn't exist 130701 11:05:59 [ERROR] Can't open the mysql.plugin table. Please run mysql_upgrade to create it. 130701 11:05:59 InnoDB: The InnoDB memory heap is disabled 130701 11:05:59 InnoDB: Mutexes and rw_locks use GCC atomic builtins 130701 11:05:59 InnoDB: Compressed tables use zlib 1.2.3.4 130701 11:05:59 InnoDB: Initializing buffer pool, size = 128.0M 130701 11:05:59 InnoDB: Completed initialization of buffer pool 130701 11:05:59 InnoDB: highest supported file format is Barracuda. 130701 11:05:59 InnoDB: Waiting for the background threads to start 130701 11:06:00 InnoDB: 5.5.31 started; log sequence number 1595675 130701 11:06:00 [Note] Server hostname (bind-address): '127.0.0.1'; port: 3306 130701 11:06:00 [Note] - '127.0.0.1' resolves to '127.0.0.1'; 130701 11:06:00 [Note] Server socket created on IP: '127.0.0.1'. 130701 11:06:00 [ERROR] Can't start server : Bind on unix socket: Permission denied 130701 11:06:00 [ERROR] Do you already have another mysqld server running on socket: /var/run/mysqld/mysqld.sock ? 130701 11:06:00 [ERROR] Aborting 130701 11:06:00 InnoDB: Starting shutdown... 130701 11:06:00 InnoDB: Shutdown completed; log sequence number 1595675 130701 11:06:00 [Note] mysqld: Shutdown complete Meanwhile I already tried to reinstall and purge the complete mysql package which results in another error which says that dpkg cant change the admins password. While this error appeared another error came with it. When trying to install something new with apt, it always says 'fopen: permission denied' right after it tries to update my man-db. This is my dmesg output: [ 6879.687998] type=1400 audit(1372669683.397:36): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/mysqld" pid=9336 comm="apparmor_parser" [ 6881.323215] init: mysql main process (9340) terminated with status 1 [ 6881.323316] init: mysql respawning too fast, stopped Any help will be appreciated as this is a productive server which renders useless without mysql.

  Read the article

• 20GB+ worth of emails in my /home what is a better solution for that?

  - by Skinkie

  My email storage requirements are outgrowing anything reasonable with respect to local mail storage. As we speak 99% of my home partition is filled with personal mail in Thunderbirds mail dirs. Needless to say, this is just painful, badly searchable and as history has proven me that backups work, but Thunderbird is capable of loosing a lot of mail very easily. Currently I have an remote IMAPS server (Dovecot) running for my daily mail, accessible from anywhere, which from my own practice works efficiently up to about 1000 emails. Then some archive directories should be used to move mail around. I have been looking into DBMail, but I wonder if I make my case worse or better which such solution. None of the supported database employ string deduplication or string compression out of the box, so is this going to help me with 20GB+ mail? What about falling back to a plain old IMAP server? A filesystem like ZFS would support stuff like GZIP transparently, which could help. Could someone share their thoughts? The 20GB mostly consists of mailinglists, and normal mail. Not things like attachments. To add some clarifications; As we speak, my mail is not server side indexed at all - only my new mail arrives at a remote IMAP server. It is all local storage from former POP3 accounts, local mirrored Gmail and IMAP accounts. In my perspective it is not Thunderbird that sucks, its fileformat that sucks. Regarding the 1000 mails. On the road I am using Alpine and MobileMail, quite happy with both of them, but some management is required to actually manage the mail. Sieve helps a lot with that, but browing through 10.000 e-mails is not fun, especially not on a mobile client. I am quite happy with Dovecot, never had any issues with it. I just wonder if this is the way to go. Or if there are any other better solutions. What my question is: what is the best practice solution that allows 20GB+ mails and is -on demand remotely accessible, easy to backup and archive worthy. It doesn't need to be available 24x7. The final approach I took was installing a local IMAP server (Dovecot), configured it for being my archive, using the following guide: http://en.gentoo-wiki.com/wiki/Dovecot/InstallThunderbird

  Read the article

• Use ASP.NET 4 Browser Definitions with ASP.NET 3.5

  - by Stephen Walther

  We updated the browser definitions files included with ASP.NET 4 to include information on recent browsers and devices such as Google Chrome and the iPhone. You can use these browser definition files with earlier versions of ASP.NET such as ASP.NET 3.5. The updated browser definition files, and instructions for installing them, can be found here: http://aspnet.codeplex.com/releases/view/41420 The changes in the browser definition files can cause backwards compatibility issues when you upgrade an ASP.NET 3.5 web application to ASP.NET 4. If you encounter compatibility issues, you can install the old browser definition files in your ASP.NET 4 application. The old browser definition files are included in the download file referenced above. What’s New in the ASP.NET 4 Browser Definition Files The complete set of browsers supported by the new ASP.NET 4 browser definition files is represented by the following figure:     If you look carefully at the figure, you’ll notice that we added browser definitions for several types of recent browsers such as Internet Explorer 8, Firefox 3.5, Google Chrome, Opera 10, and Safari 4. Furthermore, notice that we now include browser definitions for several of the most popular mobile devices: BlackBerry, IPhone, IPod, and Windows Mobile (IEMobile). The mobile devices appear in the figure with a purple background color. To improve performance, we removed a whole lot of outdated browser definitions for old cell phones and mobile devices. We also cleaned up the information contained in the browser files. Here are some of the browser features that you can detect: Are you a mobile device? <%=Request.Browser.IsMobileDevice %> Are you an IPhone? <%=Request.Browser.MobileDeviceModel == "IPhone" %> What version of JavaScript do you support? <%=Request.Browser["javascriptversion"] %> What layout engine do you use? <%=Request.Browser["layoutEngine"] %>   Here’s what you would get if you displayed the value of these properties using Internet Explorer 8: Here’s what you get when you use Google Chrome: Testing Browser Settings When working with browser definition files, it is useful to have some way to test the capability information returned when you request a page with different browsers. You can use the following method to return the HttpBrowserCapabilities the corresponds to a particular user agent string and set of browser headers: public HttpBrowserCapabilities GetBrowserCapabilities(string userAgent, NameValueCollection headers) { HttpBrowserCapabilities browserCaps = new HttpBrowserCapabilities(); Hashtable hashtable = new Hashtable(180, StringComparer.OrdinalIgnoreCase); hashtable[string.Empty] = userAgent; // The actual method uses client target browserCaps.Capabilities = hashtable; var capsFactory = new System.Web.Configuration.BrowserCapabilitiesFactory(); capsFactory.ConfigureBrowserCapabilities(headers, browserCaps); capsFactory.ConfigureCustomCapabilities(headers, browserCaps); return browserCaps; } At the end of this blog entry, there is a link to download a simple Visual Studio 2008 project – named Browser Definition Test -- that uses this method to display capability information for arbitrary user agent strings. For example, if you enter the user agent string for an iPhone then you get the results in the following figure: The Browser Definition Test application enables you to submit a user-agent string and display a table of browser capabilities information. The browser definition files contain sample user-agent strings for each browser definition. I got the iPhone user-agent string from the comments in the iphone.browser file. Enumerating Browser Definitions Someone asked in the comments whether or not there is a way to enumerate all of the browser definitions. You can do this if you ware willing to use a little reflection and read a private property. The browser definition files in the config\browsers folder get parsed into a class named BrowserCapabilitesFactory. After you run the aspnet_regbrowsers tool, you can see the source for this class in the config\browser folder by opening a file named BrowserCapsFactory.cs. The BrowserCapabilitiesFactoryBase class has a protected property named BrowserElements that represents a Hashtable of all of the browser definitions. Here's how you can read this protected property and display the ID for all of the browser definitions: var propInfo = typeof(BrowserCapabilitiesFactory).GetProperty("BrowserElements", BindingFlags.NonPublic | BindingFlags.Instance); Hashtable browserDefinitions = (Hashtable)propInfo.GetValue(new BrowserCapabilitiesFactory(), null); foreach (var key in browserDefinitions.Keys) { Response.Write("" + key); } If you run this code using Visual Studio 2008 then you get the following results: You get a huge number of outdated browsers and devices. In all, 449 browser definitions are listed. If you run this code using Visual Studio 2010 then you get the following results: In the case of Visual Studio 2010, all the old browsers and devices have been removed and you get only 19 browser definitions. Conclusion The updated browser definition files included in ASP.NET 4 provide more accurate information for recent browsers and devices. If you would like to test the new browser definitions with different user-agent strings then I recommend that you download the Browser Definition Test project: Browser Definition Test Project

  Read the article

• Security in OBIEE 11g, Part 2

  - by Rob Reynolds

  Continuing the series on OBIEE 11g, our guest blogger this week is Pravin Janardanam. Here is Part 2 of his overview of Security in OBIEE 11g. OBIEE 11g Security Overview, Part 2 by Pravin Janardanam In my previous blog on Security, I discussed the OBIEE 11g changes regarding Authentication mechanism, RPD protection and encryption. This blog will include a discussion about OBIEE 11g Authorization and other Security aspects. Authorization: Authorization in 10g was achieved using a combination of Users, Groups and association of privileges and object permissions to users and Groups. Two keys changes to Authorization in OBIEE 11g are: Application Roles Policies / Permission Groups Application Roles are introduced in OBIEE 11g. An application role is specific to the application. They can be mapped to other application roles defined in the same application scope and also to enterprise users or groups, and they are used in authorization decisions. Application roles in 11g take the place of Groups in 10g within OBIEE application. In OBIEE 10g, any changes to corporate LDAP groups require a corresponding change to Groups and their permission assignment. In OBIEE 11g, Application roles provide insulation between permission definitions and corporate LDAP Groups. Permissions are defined at Application Role level and changes to LDAP groups just require a reassignment of the Group to the Application Roles. Permissions and privileges are assigned to Application Roles and users in OBIEE 11g compared to Groups and Users in 10g. The diagram below shows the relationship between users, groups and application roles. Note that the Groups shown in the diagram refer to LDAP Groups (WebLogic Groups by default) and not OBIEE application Groups. The following screenshot compares the permission windows from Admin tool in 10g vs 11g. Note that the Groups in the OBIEE 10g are replaced with Application Roles in OBIEE 11g. The same is applicable to OBIEE web catalog objects.    The default Application Roles available after OBIEE 11g installation are BIAdministrator, BISystem, BIConsumer and BIAuthor. Application policies are the authorization policies that an application relies upon for controlling access to its resources. An Application Role is defined by the Application Policy. The following screenshot shows the policies defined for BIAdministrator and BISystem Roles. Note that the permission for impersonation is granted to BISystem Role. In OBIEE 10g, the permission to manage repositories and Impersonation were assigned to “Administrators” group with no control to separate these permissions in the Administrators group. Hence user “Administrator” also had the permission to impersonate. In OBI11g, BIAdministrator does not have the permission to impersonate. This gives more flexibility to have multiple users perform different administrative functions. Application Roles, Policies, association of Policies to application roles and association of users and groups to application roles are managed using Fusion Middleware Enterprise Manager (FMW EM). They reside in the policy store, identified by the system-jazn-data.xml file. The screenshots below show where they are created and managed in FMW EM. The following screenshot shows the assignment of WebLogic Groups to Application Roles. The following screenshot shows the assignment of Permissions to Application Roles (Application Policies). Note: Object level permission association to Applications Roles resides in the RPD for repository objects. Permissions and Privilege for web catalog objects resides in the OBIEE Web Catalog. Wherever Groups were used in the web catalog and RPD has been replaced with Application roles in OBIEE 11g. Following are the tools used in OBIEE 11g Security Administration: ·       Users and Groups are managed in Oracle WebLogic Administration console (by default). If WebLogic is integrated with other LDAP products, then Users and Groups needs to managed using the interface provide by the respective LDAP vendor – New in OBIEE 11g ·       Application Roles and Application Policies are managed in Oracle Enterprise Manager - Fusion Middleware Control – New in OBIEE 11g ·       Repository object permissions are managed in OBIEE Administration tool – Same as 10g but the assignment is to Application Roles instead of Groups ·       Presentation Services Catalog Permissions and Privileges are managed in OBI Application administration page - Same as 10g but the assignment is to Application Roles instead of Groups Credential Store: Credential Store is a single consolidated service provider to store and manage the application credentials securely. The credential store contains credentials that either user supplied or system generated. Credential store in OBIEE 10g is file based and is managed using cryptotools utility. In 11g, Credential store can be managed directly from the FMW Enterprise Manager and is stored in cwallet.sso file. By default, the Credential Store stores password for deployed RPDs, BI Publisher data sources and BISystem user. In addition, Credential store can be LDAP based but only Oracle Internet Directory is supported right now. As you can see OBIEE security is integrated with Oracle Fusion Middleware security architecture. This provides a common security framework for all components of Business Intelligence and Fusion Middleware applications.

  Read the article

• Windows Azure: Announcing Support for Windows Server 2012 R2 + Some Nice Price Cuts

  - by ScottGu

  Today we released some great updates to Windows Azure: Virtual Machines: Support for Windows Server 2012 R2 Cloud Services: Support for Windows Server 2012 R2 and .NET 4.5.1 Windows Azure Pack: Use Windows Azure features on-premises using Windows Server 2012 R2 Price Cuts: Up to 22% Price Reduction on Memory-Intensive Instances Below are more details about each of the improvements: Virtual Machines: Support for Windows Server 2012 R2 This morning we announced the release of Windows Server 2012 R2 – which is a fantastic update to Windows Server and includes a ton of great enhancements. This morning we are also excited to announce that the general availability image of Windows Server 2012 RC is now supported on Windows Azure.  Windows Azure is the first cloud provider to offer the final release of Windows Server 2012 R2, and it is incredibly easy to launch your own Windows Server 2012 R2 instance with it. To create a new Windows Server 2012 R2 instance simply choose New->Compute->Virtual Machine within the Windows Azure Management Portal.  You can select the “Windows Server 2012 R2” image and create a new Virtual Machine using the “Quick Create” option: Or alternatively click the “From Gallery” option if you want to customize even more configuration options (endpoints, remote powershell, availability set, etc): Creating and instantiating a new Virtual Machine on Windows Azure is very fast.  In fact, the Windows Server 2012 R2 image now deploys and runs 30% faster than previous versions of Windows Server. Once the VM is deployed you can drill into it to track its health and manage its settings: Clicking the “Connect” button allows you to remote desktop into the VM – at which point you can customize and manage it as a full administrator however you want: If you haven’t tried Windows Server 2012 R2 yet – give it a try with Windows Azure.  There is no easier way to get an instance of it up and running! Cloud Services: Support for using Windows Server 2012 R2 with Web and Worker Roles Today’s Windows Azure release also allows you to now use Windows Server 2012 R2 and .NET 4.5.1 within Web and Worker Roles within Cloud Service based applications.  Enabling this is easy.  You can configure existing existing Cloud Service application to use Windows Server 2012 R2 by updating your Cloud Service Configuration File (.cscfg) to use the new “OS Family 4” setting: Or alternatively you can use the Windows Azure Management Portal to update cloud services that are already deployed on Windows Azure.  Simply choose the configure tab on them and select Windows Server 2012 R2 in the Operating System Family dropdown: The approaches above enable you to immediately take advantage of Windows Server 2012 R2 and .NET 4.5.1 and all the great features they provide. Windows Azure Pack: Use Windows Azure features on Windows Server 2012 R2 Today we also made generally available the Windows Azure Pack, which is a free download that enables you to run Windows Azure Technology within your own datacenter, an on-premises private cloud environment, or with one of our service provider/hosting partners who run Windows Server. Windows Azure Pack enables you to use a management portal that has the exact same UI as the Windows Azure Management Portal, and within which you can create and manage Virtual Machines, Web Sites, and Service Bus – all of which can run on Windows Server and System Center.  The services provided with the Windows Azure Pack are consistent with the services offered within our Windows Azure public cloud offering.  This consistency enables organizations and developers to build applications and solutions that can run in any hosting environment – and which use the same development and management approach.  The end result is an offering with incredible flexibility. You can learn more about Windows Azure Pack and download/deploy it today here. Price Cuts: Up to 22% Reduction on Memory Intensive Instances Today we are also reducing prices by up to 22% on our memory-intensive VM instances (specifically our A5, A6, and A7 instances).  These price reductions apply to both Windows and Linux VM instances, as well as for Cloud Service based applications: These price reductions will take effect in November, and will enable you to run applications that demand larger memory (such as SharePoint, Databases, in-memory analytics, etc) even more cost effectively. Summary Today’s release enables you to start using Windows Server 2012 R2 within Windows Azure immediately, and take advantage of our Cloud OS vision both within our datacenters – and using the Windows Azure Pack within both your existing datacenters and those of our partners. If you don’t already have a Windows Azure account, you can sign-up for a free trial and start using all of the above features today.  Then visit the Windows Azure Developer Center to learn more about how to build apps with it. Hope this helps, Scott P.S. In addition to blogging, I am also now using Twitter for quick updates and to share links. Follow me at: twitter.com/scottgu

  Read the article

• Cannot install mysql-server (5.5.22) on clean ubuntu 12.04 LTS server

  - by Christian

  I have a clean minimal install of Ubuntu 12.04 LTS server 64-bit (just a root user and nothing alse installed). I tried to install the mysql-server with the following command: apt-get install mysql-server The installation aborts with the following error: The following NEW packages will be installed: libdbd-mysql-perl{a} libmysqlclient18{a} mysql-client mysql-client-5.5{a} mysql-client-core-5.5{a} mysql-common{a} mysql-server mysql-server-5.5{a} mysql-server-core-5.5{a} 0 packages upgraded, 9 newly installed, 0 to remove and 0 not upgraded. Need to get 11.7 kB/26.2 MB of archives. After unpacking 94.5 MB will be used. Do you want to continue? [Y/n/?] y Get: 1 http://mirror.eu.oneandone.net/ubuntu/ubuntu/ precise/main mysql-client all 5.5.22-0ubuntu1 [11.7 kB] Fetched 11.7 kB in 0s (567 kB/s) Preconfiguring packages ... Selecting previously unselected package mysql-common. (Reading database ... 54008 files and directories currently installed.) Unpacking mysql-common (from .../mysql-common_5.5.22-0ubuntu1_all.deb) ... Selecting previously unselected package libmysqlclient18. Unpacking libmysqlclient18 (from .../libmysqlclient18_5.5.22-0ubuntu1_amd64.deb) ... Selecting previously unselected package libdbd-mysql-perl. Unpacking libdbd-mysql-perl (from .../libdbd-mysql-perl_4.020-1build2_amd64.deb) ... Selecting previously unselected package mysql-client-core-5.5. Unpacking mysql-client-core-5.5 (from .../mysql-client-core-5.5_5.5.22-0ubuntu1_amd64.deb) ... Selecting previously unselected package mysql-client-5.5. Unpacking mysql-client-5.5 (from .../mysql-client-5.5_5.5.22-0ubuntu1_amd64.deb) ... Selecting previously unselected package mysql-server-core-5.5. Unpacking mysql-server-core-5.5 (from .../mysql-server-core-5.5_5.5.22-0ubuntu1_amd64.deb) ... Processing triggers for man-db ... Setting up mysql-common (5.5.22-0ubuntu1) ... Selecting previously unselected package mysql-server-5.5. (Reading database ... 54189 files and directories currently installed.) Unpacking mysql-server-5.5 (from .../mysql-server-5.5_5.5.22-0ubuntu1_amd64.deb) ... Selecting previously unselected package mysql-client. Unpacking mysql-client (from .../mysql-client_5.5.22-0ubuntu1_all.deb) ... Selecting previously unselected package mysql-server. Unpacking mysql-server (from .../mysql-server_5.5.22-0ubuntu1_all.deb) ... Processing triggers for ureadahead ... Processing triggers for man-db ... Setting up libmysqlclient18 (5.5.22-0ubuntu1) ... Setting up libdbd-mysql-perl (4.020-1build2) ... Setting up mysql-client-core-5.5 (5.5.22-0ubuntu1) ... Setting up mysql-client-5.5 (5.5.22-0ubuntu1) ... Setting up mysql-server-core-5.5 (5.5.22-0ubuntu1) ... Setting up mysql-server-5.5 (5.5.22-0ubuntu1) ... 120502 10:17:41 [Note] Plugin 'FEDERATED' is disabled. 120502 10:17:41 InnoDB: The InnoDB memory heap is disabled 120502 10:17:41 InnoDB: Mutexes and rw_locks use GCC atomic builtins 120502 10:17:41 InnoDB: Compressed tables use zlib 1.2.3.4 120502 10:17:41 InnoDB: Initializing buffer pool, size = 128.0M 120502 10:17:41 InnoDB: Completed initialization of buffer pool 120502 10:17:41 InnoDB: highest supported file format is Barracuda. 120502 10:17:41 InnoDB: Waiting for the background threads to start 120502 10:17:42 InnoDB: 1.1.8 started; log sequence number 1595675 120502 10:17:42 InnoDB: Starting shutdown... 120502 10:17:42 InnoDB: Shutdown completed; log sequence number 1595675 start: Job failed to start invoke-rc.d: initscript mysql, action "start" failed. dpkg: error processing mysql-server-5.5 (--configure): subprocess installed post-installation script returned error exit status 1 No apport report written because MaxReports is reached already Setting up mysql-client (5.5.22-0ubuntu1) ... dpkg: dependency problems prevent configuration of mysql-server: mysql-server depends on mysql-server-5.5; however: Package mysql-server-5.5 is not configured yet. dpkg: error processing mysql-server (--configure): dependency problems - leaving unconfigured No apport report written because MaxReports is reached already Processing triggers for libc-bin ... ldconfig deferred processing now taking place Errors were encountered while processing: mysql-server-5.5 mysql-server E: Sub-process /usr/bin/dpkg returned an error code (1) A package failed to install. Trying to recover: Setting up mysql-server-5.5 (5.5.22-0ubuntu1) ... start: Job failed to start invoke-rc.d: initscript mysql, action "start" failed. dpkg: error processing mysql-server-5.5 (--configure): subprocess installed post-installation script returned error exit status 1 dpkg: dependency problems prevent configuration of mysql-server: mysql-server depends on mysql-server-5.5; however: Package mysql-server-5.5 is not configured yet. dpkg: error processing mysql-server (--configure): dependency problems - leaving unconfigured Errors were encountered while processing: mysql-server-5.5 mysql-server I am completely lost because I have tried everything on the web to solve my problem (clearning the install, reconfiguring with dpkg, manually editing the my.cnf). I also set up a new clean install but nothing helped. What am I doing wrong? New information: The file /var/log/upstart/mysql.log contains the following error after the installation: AppArmor parser error for /etc/apparmor.d/usr.sbin.mysqld in /etc/apparmor.d/tunables/global at line 17: Could not open 'tunables/proc'

  Read the article

• New Product: Oracle Java ME Embedded 3.2 – Small, Smart, Connected

  - by terrencebarr

  The Internet of Things (IoT) is coming. And, with todays launch of the Oracle Java ME Embedded 3.2 product, Java is going to play an even greater role in it. Java in the Internet of Things By all accounts, intelligent embedded devices are penetrating the world around us – driving industrial processes, monitoring environmental conditions, providing better health care, analyzing and processing data, and much more. And these devices are becoming increasingly connected, adding another dimension of utility. Welcome to the Internet of Things. As I blogged yesterday, this is a huge opportunity for the Java technology and ecosystem. To enable and utilize these billions of devices effectively you need a programming model, tools, and protocols which provide a feature-rich, consistent, scalable, manageable, and interoperable platform.  Java technology is ideally suited to address these technical and business problems, enabling you eliminate many of the typical challenges in designing embedded solutions. By using Java you can focus on building smarter, more valuable embedded solutions faster. To wit, Java technology is already powering around 10 billion devices worldwide. Delivering on this vision and accelerating the growth of embedded Java solutions, Oracle is today announcing a brand-new product: Oracle Java Micro Edition (ME) Embedded 3.2, accompanied by an update release of the Java ME Software Development Kit (SDK) to version 3.2. What is Oracle Java ME Embedded 3.2? Oracle Java ME Embedded 3.2 is a complete Java runtime client, optimized for ARM architecture connected microcontrollers and other resource-constrained systems. The product provides dedicated embedded functionality and is targeted for low-power, limited memory devices requiring support for a range of network services and I/O interfaces.  What features and APIs are provided by Oracle Java ME Embedded 3.2? Oracle Java ME Embedded 3.2 is a Java ME runtime based on CLDC 1.1 (JSR-139) and IMP-NG (JSR-228). The runtime and virtual machine (VM) are highly optimized for embedded use. Also included in the product are the following optional JSRs and Oracle APIs: File I/O API’s (JSR-75)  Wireless Messaging API’s (JSR-120) Web Services (JSR-172) Security and Trust Services subset (JSR-177) Location API’s (JSR-179) XML API’s (JSR-280)  Device Access API Application Management System (AMS) API AccessPoint API Logging API Additional embedded features are: Remote application management system Support for continuous 24×7 operation Application monitoring, auto-start, and system recovery Application access to peripheral interfaces such as GPIO, I2C, SPIO, memory mapped I/O Application level logging framework, including option for remote logging Headless on-device debugging – source level Java application debugging over IP Connection Remote configuration of the Java VM What type of platforms are targeted by Oracle Java ME 3.2 Embedded? The product is designed for embedded, always-on, resource-constrained, headless (no graphics/no UI), connected (wired or wireless) devices with a variety of peripheral I/O.  The high-level system requirements are as follows: System based on ARM architecture SOCs Memory footprint (approximate) from 130 KB RAM/350KB ROM (for a minimal, customized configuration) to 700 KB RAM/1500 KB ROM (for the full, standard configuration)  Very simple embedded kernel, or a more capable embedded OS/RTOS At least one type of network connection (wired or wireless) The initial release of the product is delivered as a device emulation environment for x86/Windows desktop computers, integrated with the Java ME SDK 3.2. A standard binary of Oracle Java ME Embedded 3.2 for ARM KEIL development boards based on ARM Cortex M-3/4 (KEIL MCBSTM32F200 using ST Micro SOC STM32F207IG) will soon be available for download from the Oracle Technology Network (OTN).  What types of applications can I develop with Oracle Java ME Embedded 3.2? The Oracle Java ME Embedded 3.2 product is a full-featured embedded Java runtime supporting applications based on the IMP-NG application model, which is derived from the well-known MIDP 2 application model. The runtime supports execution of multiple concurrent applications, remote application management, versatile connectivity, and a rich set of APIs and features relevant for embedded use cases, including the ability to interact with peripheral I/O directly from Java applications. This rich feature set, coupled with familiar and best-in class software development tools, allows developers to quickly build and deploy sophisticated embedded solutions for a wide range of use cases. Target markets well supported by Oracle Java ME Embedded 3.2 include wireless modules for M2M, industrial and building control, smart grid infrastructure, home automation, and environmental sensors and tracking. What tools are available for embedded application development for Oracle Java ME Embedded 3.2? Along with the release of Oracle Java ME Embedded 3.2, Oracle is also making available an updated version of the Java ME Software Development Kit (SDK), together with plug-ins for the NetBeans and Eclipse IDEs, to deliver a complete development environment for embedded application development.  OK – sounds great! Where can I find out more? And how do I get started? There is a complete set of information, data sheet, API documentation, “Getting Started Guide”, FAQ, and download links available: For an overview of Oracle Embeddable Java, see here. For the Oracle Java ME Embedded 3.2 press release, see here. For the Oracle Java ME Embedded 3.2 data sheet, see here. For the Oracle Java ME Embedded 3.2 landing page, see here. For the Oracle Java ME Embedded 3.2 documentation page, including a “Getting Started Guide” and FAQ, see here. For the Oracle Java ME SDK 3.2 landing and download page, see here. Finally, to ask more questions, please see the OTN “Java ME Embedded” forum To get started, grab the “Getting Started Guide” and download the Java ME SDK 3.2, which includes the Oracle Java ME Embedded 3.2 device emulation.  Can I learn more about Oracle Java ME Embedded 3.2 at JavaOne and/or Java Embedded @ JavaOne? Glad you asked Both conferences, JavaOne and Java Embedded @ JavaOne, will feature a host of content and information around the new Oracle Java ME Embedded 3.2 product, from technical and business sessions, to hands-on tutorials, and demos. Stay tuned, I will post details shortly. Cheers, – Terrence Filed under: Mobile & Embedded Tagged: "Oracle Java ME Embedded", Connected, embedded, Embedded Java, Java Embedded @ JavaOne, JavaOne, Smart

  Read the article

• Setup Remote Access in Windows Home Server

  - by Mysticgeek

  One of the many awesome features of Windows Home Server, is the ability to access your server and other computers on your network remotely. Today we show you the steps to enable Remote Access to your home server from anywhere you have an Internet connection. Remote Access in Windows Home Server has a lot of great features like uploading and downloading files from shared folders, accessing files from machines on your network, and controling machines remotely (on supported OS versions). Here we take a look at the basics of setting it up, choosing a domain name, and verifying you can connect remotely. Setup Remote Access in Windows Home Server Open the Windows Home Server Console and click on Settings. Next select Remote Access, it is off by default, just click the button to turn it on. Wait while your router is configured for remote access, when it’s complete click Next. Notice that it will enable UPnP, if you don’t wish to have that enabled, you can manually forward the correct ports. If you have any problems with the router being automatically configured, we’ll be taking a look at a more detailed troubleshooting guide in the future. The router is successfully configured, and we can continue to the next process of configuring our domain name. The Domain Name Setup Wizard will start. Notice you will need a Windows Live ID to set it up –which is typically your hotmail address. If you don’t already have one, you can get one here. Type in your Live ID email address and password and click Next… Agree to the Home Server Privacy Statement and the Live Custom Domains Addendum. If you’re concerned about privacy and want to learn more about the domain addendum, make sure to read about it before agreeing. There is nothing abnormal to point out about either statement, but if this is your first time setting it up, it’s good to review the information.   Now choose a name for the domain. You should select something that is easy to remember and identifies your home server. The name can contain up to 63 characters, numbers, letters, and hyphens…and must begin and end with a letter or number. When you have the name figured out click the Confirm button. Note: You can only register one domain name per Live ID. If the name isn’t already taken, you’ll get a confirmation message indicating it’s god to go. The wizard is complete and you can now access the home server from the URL provided. A few other things to point out after you’ve set it up…under Domain Name click on the Details button… Which pulls up the domain detail information and you can refresh the data to verify everything is working correctly. Or you can click the Configure button and then change or release your current domain name. Under Web site settings, you can change you site page headline to whatever you want it to be. Accessing Home Server Remotely After you’ve gotten everything setup for your home server domain, you can begin to access it when you’re away from home. Simply type in the domain address you created in the previous steps. The start page is rather boring…and to start accessing your data, click the Log On button in the upper right hand corner. Then enter in your home server credentials to gain access to your files, folders, and network computers. You won’t be able to log in with your administrator user account however, to protect security of your network. Once you’re logged in, you’ll be able to access different parts of your home server shares and network computers. Conclusion Now that you have Remote Access setup, you should be able to access and manage your files easily. Being able to access data from your home server remotely is great when you need to get certain files while on the road. The web UI is pretty self explanatory, works best in IE as ActiveX is required, and is smooth and easy to work with. In future articles we’ll be covering a lot more regarding remote access, including more of the available features, troubleshooting connection issues, and enabling access for other users. Similar Articles Productive Geek Tips GMedia Blog: Setting Up a Windows Home ServerHow to Remote Desktop to the Actual Server Console on Windows 2003Use Windows Vista Aero through Remote Desktop ConnectionAccess Your MySQL Server Remotely Over SSHShare Ubuntu Home Directories using Samba TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Penolo Lets You Share Sketches On Twitter Visit Woolyss.com for Old School Games, Music and Videos Add a Custom Title in IE using Spybot or Spyware Blaster When You Need to Hail a Taxi in NYC Live Map of Marine Traffic NoSquint Remembers Site Specific Zoom Levels (Firefox)

  Read the article

< Previous Page | 149 150 151 152 153 154 155 156 157 158 159 160  | Next Page >