Search Results

Search found 7526 results on 302 pages for 'week in geek'.

Page 153/302 | < Previous Page | 149 150 151 152 153 154 155 156 157 158 159 160  | Next Page >

• Bad disks in ancient server

  - by Joel Coel

  I have a 1998-era Netware 3.12 server that runs everything on our campus: general ledger, purchasing, payroll, student information, grades, you name it. The server has an Adaptec RAID controller with two volumes: RAID 1, 2 17GB scsi disks, Seagate ST318417W RAID 5, 3 4GB scsi disks, 2 Seagate ST34573W and 1 ST34572W. We are currently in the early stages of a project to replace this system, but you don't just jump into a new system like that and so I need to keep this server running until at least November 2011. This week we had not one but two hard drives fail. Thankfully they are from different volumes and we're able to keep running for the moment, but given the close nature of these failures I have serious doubts that I'll be able to avoid catastrophic failure from this server through the November target as is without restoring the RAID redundancy — it'll only take one more drive failure anywhere and I'm completely hosed. We are fortunate enough to have exact match "spares" lying around for both drives, but the spares are in unknown condition. I tried swapping just them in, but the RAID controller isn't smart enough to handle this and it renders the system unbootable. As for the RAID controller itself, there is utility I can get into during POST via a Ctrl-A shortcut, but I can't do much useful from there. To actually manage volumes I must first boot in to Netware, at which point I can use CI/O Array Management Software Version 2.0 to actually look at volume information. I suspect that the normal way to manage things is to boot from a special floppy with the controller software on it, but that floppy is long gone. Going through the options in the RAID software, I think the only supported way to replace a disk in an existing RAID volume is to physically add the disk, boot up and configure it as a "spare" for a volume, force the volume to use the spare to replace an existing down disk (and at this point I'm only guessing) so that the down disk becomes the spare, repair the volume, remove the spare from the volume, and then shut down and remove the disk. Then start all over for the other failed disk. All this amounts to a lot of downtime, assuming I can even make it work and that my spares are any good. As for finding reliable spares, I have no clue where to even begin looking to find a new 4GB scsi drive, or even which exact scsi system I'm looking for, as it's gone through a few different iterations over time. Another option is to migrate this to a virtual machine (hyper-v), but all previous attempts we've made in this area have failed to get very far. When this machine was installed I was just graduating from high school, and so it requires lower level knowledge of netware and dos than I ever developed, or if I did have since forgotten (I'm not exactly a dos neophyte, either). Part of my problem is this is a high-use server, and taking it down for a few days to figure things out isn't gonna fly very well. As for the question, I'm looking for anything that might be helpful in this situation: a recommendation on a place to find good spares from this era, personal experience repairing RAID volumes using a similar controller or building a hyper-v vm from an old netware server, a line on a floppy with better software for the RAID controller, recommendation on a good Novell consultant in Nebraska that would be able to put things right, a whole other option I haven't considered yet, etc. Update: For backups, we have good (recently verified via restore) backups of the data only -- nothing for the software that actually runs things. Update 2: Just a progress report that I currently have a working Netware 3.12 install in VMWare Virtual Server 2.0, thanks largely to the guide I found here: http://cerbulescubogdan.blogspot.com/2010/11/novell-netware-312-on-vmware.html The next steps are preparing empty netware volumes to match the additional volumes on my existing server, taking a dump of everything on the C:\ drive and netware volumes on my existing server, and figuring out from that information what modules need added to netware, installing my licenses (we do still have that disk, if it's any good), and moving data over. I have approval to bring the server down for a week after the first of the year (sadly not before), so, aside from creating empty volumes, the rest of the work will have to wait until then. Final Update (Jan 5, 2011): I was able to get spares working in both raid arrays without data loss this week. Both are now listed by the controller as "FAULT TOLLERANT" (yay!). I was also able to build on the progress from my last update and now have a functional "spare" server in VMWare Server 2.0. The spare can run and use our erp software, but I can't put it into production because I can't (yet) print from that box (and I have no idea why). Even so, this VM will do in a pinch if I have no other choice, and between it and the repaired RAID arrays I'm comfortable pushing on until I can junk the machine in November.

  Read the article

• Extend GWT widget built using UIBinder

  - by Eric Landry

  I'm trying to extend a GWT widget that is built using UIBinder. UIBinder expects the fields in ui.xml to be in the extended widget. The problem that was well described by 'Blessed Geek' on Google Groups. Any tips/tricks?

  Read the article

• Is MapReduce one form of Continuation-Passing Style (CPS)?

  - by Jeffrey

  As the title says. I was reading Yet Another Language Geek: Continuation-Passing Style and I was sort of wondering if MapReduce can be categorized as one form of Continuation-Passing Style aka CPS. I am also wondering how can CPS utilise more than one computer to perform complex computation. Maybe CPS makes it easier to work with Actor model.

  Read the article

• What is the technical skill degree of your co-workers?

  - by bonefisher

  For now it has been around 4 years that I work as developer. Most of my team mates, from their tech-skill, programming ability and code practices view, are somewhere between junior and senior. In all my previous jobs, there was a real geek who was brilliant at coding/analyzing/lead, but the others were just 'average' programmers. How would you rank your co-workers as good developers from rank 1 (best) - 5 (worst) ?

  Read the article

• What did you develop using a microcontroller?

  - by DR

  I've always been fascinated by microcontrollers and I'm planning to do a few hobby projects just to satisfy my inner geek :) I'm looking for ideas and motivation, so what did you develop using a microcontroller? If possible please state the microcontroller and/or development environment and an estimate on hardware costs beyond the basic equipment (if applicable). I'm interested in both successful and failed projects and any problems you encountered.

  Read the article

• A reliable, Australia-based ASP.NET Web Hosting

  - by Leonardo

  In the excellent Secret Geek’s Building a Micro-ISV series, Leon Bambrick admits that he prefers to host his sites in the US because of the prices and proximity to his target market. For Australian companies and start-ups, what’s the best ASP.NET web hosting in the country? Should a company consider hosting its website overseas even if the potential market is in here?

  Read the article

• What reasons are there NOT to use OpenID?

  - by cletus

  You see a fair bit (in the Geek community anyway) about OpenID. It seems like a good idea. I'm developing a website that will be targeted at a somewhat less geeky audience (but not quite Mom and Pops either) so I have to wonder if OpenID is going to be "too hard" for some audiences. What do you think? That aside, are there any other technical or non-technical reasons NOT to use OpenID?

  Read the article

• Professional Scrum Developer (.NET) Training in London

  - by Martin Hinshelwood

  On the 26th - 30th July in Microsoft’s offices in London Adam Cogan from SSW will be presenting the first Professional Scrum Developer course in the UK. I will be teaching this course along side Adam and it is a fantastic experience. You are split into teams and go head-to-head to deliver units of potentially shippable work in four two hour sprints. The Professional Scrum Developer course is the only course endorsed by both Microsoft and Ken Schwaber and they have worked together very effectively in brining this course to fruition. This course is the brain child of Richard Hundhausen, a Microsoft Regional Director, and both Adam and I attending the Trainer Prep in Sydney when he was there earlier this year. He is a fantastic trainer and no matter where you do this course you can be safe in the knowledge that he has trained and vetted all of the teachers. A tools version of Ken if you will Find a course and register Download this syllabus Download the Scrum Guide What is the Professional Scrum Developer course all about? Professional Scrum Developer course is a unique and intensive five-day experience for software developers. The course guides teams on how to turn product requirements into potentially shippable increments of software using the Scrum framework, Visual Studio 2010, and modern software engineering practices. Attendees will work in self-organizing, self-managing teams using a common instance of Team Foundation Server 2010. Who should attend this course? This course is suitable for any member of a software development team – architect, programmer, database developer, tester, etc. Entire teams are encouraged to attend and experience the course together, but individuals are welcome too. Attendees will self-organize to form cross-functional Scrum teams. These teams require an aggregate of skills specific to the selected case study. Please see the last page of this document for specific details. Product Owners, ScrumMasters, and other stakeholders are welcome too, but keep in mind that everyone who attends will be expected to commit to work and pull their weight on a Scrum team. What should you know by the end of the course? Scrum will be experienced through a combination of lecture, demonstration, discussion, and hands-on exercises. Attendees will learn how to do Scrum correctly while being coached and critiqued by the instructor, in the following topic areas: Form effective teams Explore and understand legacy “Brownfield” architecture Define quality attributes, acceptance criteria, and “done” Create automated builds How to handle software hotfixes Verify that bugs are identified and eliminated Plan releases and sprints Estimate product backlog items Create and manage a sprint backlog Hold an effective sprint review Improve your process by using retrospectives Use emergent architecture to avoid technical debt Use Test Driven Development as a design tool Setup and leverage continuous integration Use Test Impact Analysis to decrease testing times Manage SQL Server development in an Agile way Use .NET and T-SQL refactoring effectively Build, deploy, and test SQL Server databases Create and manage test plans and cases Create, run, record, and play back manual tests Setup a branching strategy and branch code Write more maintainable code Identify and eliminate people and process dysfunctions Inspect and improve your team’s software development process What does the week look like? This course is a mix of lecture, demonstration, group discussion, simulation, and hands-on software development. The bulk of the course will be spent working as a team on a case study application delivering increments of new functionality in mini-sprints. Here is the week at a glance: Monday morning and most of the day Friday will be spent with the computers powered off, so you can focus on sharpening your game of Scrum and avoiding the common pitfalls when implementing it. The Sprints Timeboxing is a critical concept in Scrum as well as in this course. We expect each team and student to understand and obey all of the timeboxes. The timebox duration will always be clearly displayed during each activity. Expect the instructor to enforce it. Each of the ½ day sprints will roughly follow this schedule: Component Description Minutes Instruction Presentation and demonstration of new and relevant tools & practices 60 Sprint planning meeting Product owner presents backlog; each team commits to delivering functionality 10 Sprint planning meeting Each team determines how to build the functionality 10 The Sprint The team self-organizes and self-manages to complete their tasks 120 Sprint Review meeting Each team will present their increment of functionality to the other teams = 30 Sprint Retrospective A group retrospective meeting will be held to inspect and adapt 10 Each team is expected to self-organize and manage their own work during the sprint. Pairing is highly encouraged. The instructor/product owner will be available if there are questions or impediments, but will be hands-off by default. You should be prepared to communicate and work with your team members in order to achieve your sprint goal. If you have development-related questions or get stuck, your partner or team should be your first level of support. Module 1: INTRODUCTION This module provides a chance for the attendees to get to know the instructors as well as each other. The Professional Scrum Developer program, as well as the day by day agenda, will be explained. Finally, the Scrum team will be selected and assembled so that the forming, storming, norming, and performing can begin. Trainer and student introductions Professional Scrum Developer program Agenda Logistics Team formation Retrospective Module 2: SCRUMDAMENTALS This module provides a level-setting understanding of the Scrum framework including the roles, timeboxes, and artifacts. The team will then experience Scrum firsthand by simulating a multi-day sprint of product development, including planning, review, and retrospective meetings. Scrum overview Scrum roles Scrum timeboxes (ceremonies) Scrum artifacts Simulation Retrospective It’s required that you read Ken Schwaber’s Scrum Guide in preparation for this module and course. MODULE 3: IMPLEMENTING SCRUM IN VISUAL STUDIO 2010 This module demonstrates how to implement Scrum in Visual Studio 2010 using a Scrum process template*. The team will learn the mapping between the Scrum concepts and how they are implemented in the tool. After connecting to the shared Team Foundation Server, the team members will then return to the simulation – this time using Visual Studio to manage their product development. Mapping Scrum to Visual Studio 2010 User Story work items Task work items Bug work items Demonstration Simulation Retrospective Module 4: THE CASE STUDY In this module the team is introduced to their problem domain for the week. A kickoff meeting by the Product Owner (the instructor) will set the stage for the why and what that will take during the upcoming sprints. The team will then define the quality attributes of the project and their definition of “done.” The legacy application code will be downloaded, built, and explored, so that any bugs can be discovered and reported. Introduction to the case study Download the source code, build, and explore the application Define the quality attributes for the project Define “done” How to file effective bugs in Visual Studio 2010 Retrospective Module 5: HOTFIX This module drops the team directly into a Brownfield (legacy) experience by forcing them to analyze the existing application’s architecture and code in order to locate and fix the Product Owner’s high-priority bug(s). The team will learn best practices around finding, testing, fixing, validating, and closing a bug. How to use Architecture Explorer to visualize and explore Create a unit test to validate the existence of a bug Find and fix the bug Validate and close the bug Retrospective Module 6: PLANNING This short module introduces the team to release and sprint planning within Visual Studio 2010. The team will define and capture their goals as well as other important planning information. Release vs. Sprint planning Release planning and the Product Backlog Product Backlog prioritization Acceptance criteria and tests Sprint planning and the Sprint Backlog Creating and linking Sprint tasks Retrospective At this point the team will have the knowledge of Scrum, Visual Studio 2010, and the case study application to begin developing increments of potentially shippable functionality that meet their definition of done. Module 7: EMERGENT ARCHITECTURE This module introduces the architectural practices and tools a team can use to develop a valid design on which to develop new functionality. The teams will learn how Scrum supports good architecture and design practices. After the discussion, the teams will be presented with the product owner’s prioritized backlog so that they may select and commit to the functionality they can deliver in this sprint. Architecture and Scrum Emergent architecture Principles, patterns, and practices Visual Studio 2010 modeling tools UML and layer diagrams SPRINT 1 Retrospective Module 8: TEST DRIVEN DEVELOPMENT This module introduces Test Driven Development as a design tool and how to implement it using Visual Studio 2010. To maximize productivity and quality, a Scrum team should setup Continuous Integration to regularly build every team member’s code changes and run regression tests. Refactoring will also be defined and demonstrated in combination with Visual Studio’s Test Impact Analysis to efficiently re-run just those tests which were impacted by refactoring. Continuous integration Team Foundation Build Test Driven Development (TDD) Refactoring Test Impact Analysis SPRINT 2 Retrospective Module 9: AGILE DATABASE DEVELOPMENT This module lets the SQL Server database developers in on a little secret – they can be agile too. By using the database projects in Visual Studio 2010, the database developers can join the rest of the team. The students will see how to apply Agile database techniques within Visual Studio to support the SQL Server 2005/2008/2008R2 development lifecycle. Agile database development Visual Studio database projects Importing schema and scripts Building and deploying Generating data Unit testing SPRINT 3 Retrospective Module 10: SHIP IT Teams need to know that just because they like the functionality doesn’t mean the Product Owner will. This module revisits acceptance criteria as it pertains to acceptance testing. By refining acceptance criteria into manual test steps, team members can execute the tests, recording the results and reporting bugs in a number of ways. Manual tests will be defined and executed using the Microsoft Test Manager tool. As the Sprint completes and an increment of functionality is delivered, the team will also learn why and when they should create a branch of the codeline. Acceptance criteria Testing in Visual Studio 2010 Microsoft Test Manager Writing and running manual tests Branching SPRINT 4 Retrospective Module 11: OVERCOMING DYSFUNCTION This module introduces the many types of people, process, and tool dysfunctions that teams face in the real world. Many dysfunctions and scenarios will be identified, along with ideas and discussion for how a team might mitigate them. This module will enable you and your team to move toward independence and improve your game of Scrum when you depart class. Scrum-butts and flaccid Scrum Best practices working as a team Team challenges ScrumMaster challenges Product Owner challenges Stakeholder challenges Course Retrospective What will be expected of you and you team? This is a unique course in that it’s technically-focused, team-based, and employs timeboxes. It demands that the members of the teams self-organize and self-manage their own work to collaboratively develop increments of software. All attendees must commit to: Pay attention to all lectures and demonstrations Participate in team and group discussions Work collaboratively with other team members Obey the timebox for each activity Commit to work and do your best to deliver All teams should have these skills: Understanding of Scrum Familiarity with Visual Studio 201 C#, .NET 4.0 & ASP.NET 4.0 experience*  SQL Server 2008 development experience Software testing experience * Check with the instructor ahead of time for the exact technologies Self-organising teams Another unique attribute of this course is that it’s a technical training class being delivered to teams of developers, not pairs, and not individuals. Ideally, your actual software development team will attend the training to ensure that all necessary skills are covered. However, if you wish to attend an open enrolment course alone or with just a couple of colleagues, realize that you may be placed on a team with other attendees. The instructor will do his or her best to ensure that each team is cross-functional to tackle the case study, but there are no guarantees. You may be required to try a new role, learn a new skill, or pair with somebody unfamiliar to you. This is just good Scrum! Who should NOT take this course? Because of the nature of this course, as explained above, certain types of people should probably not attend this course: Students requiring command and control style instruction – there are no prescriptive/step-by-step (think traditional Microsoft Learning) labs in this course Students who are unwilling to work within a timebox Students who are unwilling to work collaboratively on a team Students who don’t have any skill in any of the software development disciplines Students who are unable to commit fully to their team – not only will this diminish the student’s learning experience, but it will also impact their team’s learning experience Find a course and register Download this syllabus Download the Scrum Guide Technorati Tags: Scrum,SSW,Pro Scrum Dev

  Read the article

• Visual Studio 2010 Productivity Tips and Tricks-Part 2: Key Shortcuts

  - by ToStringTheory

  Ask anyone that knows me, and they will confirm that I hate the mouse.  This isn’t because I deny affection to objects that don’t look like their mammalian-named self, but rather for a much more simple and not-insane reason: I have terrible eyesight.  Introduction Thanks to a degenerative eye disease known as Choroideremia, I have learned to rely more on the keyboard which I can feel digital/static positions of keys relative to my fingers, than the much more analog/random position of the mouse.  Now, I would like to share some of the keyboard shortcuts with you now, as I believe that they not only increase my productivity, but yours as well once you know them (if you don’t already of course)...  I share one of my biggest tips for productivity in the conclusion at the end. Visual Studio Key Shortcuts Global Editor Shortcuts These are shortcuts that are available from almost any application running in Windows, however are many times forgotten. Shortcut Action Visual Studio 2010 Functionality Ctrl + X Cut This shortcut works without a selection. If nothing is selected, the entire line that the caret is on is cut from the editor. Ctrl + C Copy This shortcut works without a selection. If nothing is selected, the entire line that the caret is on is copied from the editor. Ctrl + V Paste If you copied an entire line by the method above, the data is pasted in the line above the current caret line. Ctrl + Shift + V Next Clipboard Element Cut/Copy multiple things, and then hit this combo repeatedly to switch to the next clipboard item when pasting. Ctrl + Backspace Delete Previous Will delete the previous word from the editor directly before the caret. If anything is selected, will just delete that. Ctrl + Del Delete Next Word Will delete the next word/space from the editor directly after the caret. If anything is selected, will just delete that. Shift + Del Delete Focused Line Will delete the line from the editor that the caret is on. If something is selected, will just delete that. Ctrl + ? or Ctrl + ? Left/Right by Word This will move the caret left or right by word or special character boundary. Holding Shift will also select the word. Ctrl + F Quick Find Either the Quick Find panel, or the search bar if you have the Productivity Power Tools installed. Ctrl + Shift + F Find in Solution Opens up the 'Find in Files' window, allowing you to search your solution, as well as using regex for pattern matching. F2 Rename File... While not debugging, selecting a file in the solution explorer\navigator and pressing F2 allows you to rename the selected file. Global Application Shortcuts These are shortcuts that are available from almost any application running in Windows, however are many times forgotten... Again... Shortcut Action Visual Studio 2010 Functionality Ctrl + N New File dialog Opens up the 'New File' dialog to add a new file to the current directory in the Solution\Project. Ctrl + O Open File dialog Opens up the 'Open File' dialog to open a file in the editor, not necessarily in the solution. Ctrl + S Save File dialog Saves the currently focused editor tab back to your HDD/SSD. Ctrl + Shift + S Save All... Quickly save all open/edited documents back to your disk. Ctrl + Tab Switch Panel\Tab Tapping this combo switches between tabs quickly. Holding down Ctrl when hitting tab will bring up a chooser window. Building Shortcuts These are shortcuts that are focused on building and running a solution. These are not usable when the IDE is in Debug mode, as the shortcut changes by context. Shortcut Action Visual Studio 2010 Functionality Ctrl + Shift + B Build Solution Starts a build process on the solution according to the current build configuration manager settings. Ctrl + Break Cancel a Building Solution Will cancel a build operation currently in progress. Good for long running builds when you think of one last change. F5 Start Debugging Will build the solution if needed and launch debugging according to the current configuration manager settings. Ctrl + F5 Start Without Debugger Will build the solution if needed and launch the startup project without attaching a debugger. Debugging Shortcuts These are shortcuts that are used when debugging a solution. Shortcut Action Visual Studio 2010 Functionality F5 Continue Execution Continues execution of code until the next breakpoint. Ctrl + Alt + Break Pause Execution Pauses the program execution. Shift + F5 Stop Debugging Stops the current debugging session. NOTE: Web apps will still continue processing after stopping the debugger. Keep this in mind if working on code such as credit card processing. Ctrl + Shift + F5 Restart Debugging Stops the current debugging session and restarts the debugging session from the beginning. F9 Place Breakpoint Toggles/Places a breakpoint in the editor on the current line. Set a breakpoint in condensed code by highlighting the statement first. F10 Step Over Statement When debugging, executes all code in methods/properties on the current line until the next line. F11 Step Into Statement When debugging, steps into a method call so you can walk through the code executed there (if available). Ctrl + Alt + I Immediate Window Open the Immediate Window to execute commands when execution is paused. Navigation Shortcuts These are shortcuts that are used for navigating in the IDE or editor panel. Shortcut Action Visual Studio 2010 Functionality F4 Properties Panel Opens the properties panel for the selected item in the editor/designer/solution navigator (context driven). F12 Go to Definition Press F12 with the caret on a member to navigate to its declaration. With the Productivity tools, Ctrl + Click works too. Ctrl + K Ctrl + T View Call Hierarchy View the call hierarchy of the member the caret is on. Great for going through n-tier solutions and interface implementations! Ctrl + Alt + B Breakpoint Window View the breakpoint window to manage breakpoints and their advanced options. Allows easy toggling of breakpoints. Ctrl + Alt + L Solution Navigator Open the solution explorer panel. Ctrl + Alt + O Output Window View the output window to see build\general output from Visual Studio. Ctrl + Alt + Enter Live Web Preview Only available with the Web Essential plugin. Launches the auto-updating Preview panel. Testing Shortcuts These are shortcuts that are used for running tests in the IDE. Please note, Visual Studio 2010 is all about context. If your caret is within a test method when you use one of these combinations, the combination will apply to that test. If your caret is within a test class, it will apply to that class. If the caret is outside of a test class, it will apply to all tests. Shortcut Action Visual Studio 2010 Functionality Ctrl + R T Run Test(s) Run all tests in the current context without a debugger attached. Breakpoints will not be stopped on. Ctrl + R Ctrl + T Run Test(s) (Debug) Run all tests in the current context with a debugger attached. This allows you to use breakpoints. Substitute A for T from the preceding combos to run/debug ALL tests in the current context. Substitute Y for T from the preceding combos to run/debug ALL impacted/covering tests for a method in the current context. Advanced Editor Shortcuts These are shortcuts that are used for more advanced editing in the editor window. Shortcut Action Visual Studio 2010 Functionality Shift + Alt + ? Shift + Alt + ? Multiline caret up/down Use this combo to edit multiple lines at once. Not too many uses for it, but once in a blue moon one comes along. Ctrl + Alt + Enter Insert Line Above Inserts a blank line above the line the caret is currently on. No need to be at end or start of line, so no cutting off words/code. Ctrl + K Ctrl + C Comment Selection Comments the current selection out of compilation. Ctrl + K Ctrl + U Uncomment Selection Uncomments the current selection into compilation. Ctrl + K Ctrl + D Format Document Automatically formats the document into a structured layout. Lines up nodes or code into columns intelligently. Alt + ? Alt + ? Code line up/down *Use this combo to move a line of code up or down quickly. Great for small rearrangements of code. *Requires the Productivity Power pack from Microsoft. Conclusion This list is by no means meant to be exhaustive, but these are the shortcuts I use regularly every hour/minute of the day. There are still 100s more in Visual Studio that you can discover through the configuration window, or by tooltips. Something that I started doing months ago seems to have interest in my office.. In my last post, I talked about how I hated a cluttered UI. One of the ways that I aimed to resolve that was by systematically cleaning up the toolbars week by week. First day, I removed ALL icons that I already knew shortcuts to, or would never use them (Undo in a toolbar?!). Then, every week from that point on, I make it a point to remove an icon/two from the toolbar and make an effort to remember its key combination. I gain extra space in the toolbar area, AND become more productive at the same time! I hope that you found this article interesting or at least somewhat informative.. Maybe a shortcut or two you didn't know. I know some of them seem trivial, but I often see people going to the edit menu for Copy/Paste... Thought a refresher might be helpful!

  Read the article

• SQL SERVER – Weekly Series – Memory Lane – #039

  - by Pinal Dave

  Here is the list of selected articles of SQLAuthority.com across all these years. Instead of just listing all the articles I have selected a few of my most favorite articles and have listed them here with additional notes below it. Let me know which one of the following is your favorite article from memory lane. 2007 FQL – Facebook Query Language Facebook list following advantages of FQL: Condensed XML reduces bandwidth and parsing costs. More complex requests can reduce the number of requests necessary. Provides a single consistent, unified interface for all of your data. It’s fun! UDF – Get the Day of the Week Function The day of the week can be retrieved in SQL Server by using the DatePart function. The value returned by the function is between 1 (Sunday) and 7 (Saturday). To convert this to a string representing the day of the week, use a CASE statement. UDF – Function to Get Previous And Next Work Day – Exclude Saturday and Sunday While reading ColdFusion blog of Ben Nadel Getting the Previous Day In ColdFusion, Excluding Saturday And Sunday, I realize that I use similar function on my SQL Server Database. This function excludes the Weekends (Saturday and Sunday), and it gets previous as well as next work day. Complete Series of SQL Server Interview Questions and Answers Data Warehousing Interview Questions and Answers – Introduction Data Warehousing Interview Questions and Answers – Part 1 Data Warehousing Interview Questions and Answers – Part 2 Data Warehousing Interview Questions and Answers – Part 3 Data Warehousing Interview Questions and Answers Complete List Download 2008 Introduction to Log Viewer In SQL Server all the windows event logs can be seen along with SQL Server logs. Interface for all the logs is same and can be launched from the same place. This log can be exported and filtered as well. DBCC SHRINKFILE Takes Long Time to Run If you are DBA who are involved with Database Maintenance and file group maintenance, you must have experience that many times DBCC SHRINKFILE operations takes a long time but any other operations with Database are relatively quicker. mssqlsystemresource – Resource Database The purpose of resource database is to facilitates upgrading to the new version of SQL Server without any hassle. In previous versions whenever version of SQL Server was upgraded all the previous version system objects needs to be dropped and new version system objects to be created. 2009 Puzzle – Write Script to Generate Primary Key and Foreign Key In SQL Server Management Studio (SSMS), there is no option to script all the keys. If one is required to script keys they will have to manually script each key one at a time. If database has many tables, generating one key at a time can be a very intricate task. I want to throw a question to all of you if any of you have scripts for the same purpose. Maximizing View of SQL Server Management Studio – Full Screen – New Screen I had explained the following two different methods: 1) Open Results in Separate Tab - This is a very interesting method as result pan shows up in a different tab instead of the splitting screen horizontally. 2) Open SSMS in Full Screen - This works always and to its best. Not many people are aware of this method; hence, very few people use it to enhance performance. 2010 Find Queries using Parallelism from Cached Plan T-SQL script gets all the queries and their execution plan where parallelism operations are kicked up. Pay attention there is TOP 10 is used, if you have lots of transactional operations, I suggest that you change TOP 10 to TOP 50 This is the list of the all the articles in the series of computed columns. SQL SERVER – Computed Column – PERSISTED and Storage This article talks about how computed columns are created and why they take more storage space than before. SQL SERVER – Computed Column – PERSISTED and Performance This article talks about how PERSISTED columns give better performance than non-persisted columns. SQL SERVER – Computed Column – PERSISTED and Performance – Part 2 This article talks about how non-persisted columns give better performance than PERSISTED columns. SQL SERVER – Computed Column and Performance – Part 3 This article talks about how Index improves the performance of Computed Columns. SQL SERVER – Computed Column – PERSISTED and Storage – Part 2 This article talks about how creating index on computed column does not grow the row length of table. SQL SERVER – Computed Columns – Index and Performance This article summarized all the articles related to computed columns. 2011 SQL SERVER – Interview Questions and Answers – Frequently Asked Questions – Data Warehousing Concepts – Day 21 of 31 What is Data Warehousing? What is Business Intelligence (BI)? What is a Dimension Table? What is Dimensional Modeling? What is a Fact Table? What are the Fundamental Stages of Data Warehousing? What are the Different Methods of Loading Dimension tables? Describes the Foreign Key Columns in Fact Table and Dimension Table? What is Data Mining? What is the Difference between a View and a Materialized View? SQL SERVER – Interview Questions and Answers – Frequently Asked Questions – Data Warehousing Concepts – Day 22 of 31 What is OLTP? What is OLAP? What is the Difference between OLTP and OLAP? What is ODS? What is ER Diagram? SQL SERVER – Interview Questions and Answers – Frequently Asked Questions – Data Warehousing Concepts – Day 23 of 31 What is ETL? What is VLDB? Is OLTP Database is Design Optimal for Data Warehouse? If denormalizing improves Data Warehouse Processes, then why is the Fact Table is in the Normal Form? What are Lookup Tables? What are Aggregate Tables? What is Real-Time Data-Warehousing? What are Conformed Dimensions? What is a Conformed Fact? How do you Load the Time Dimension? What is a Level of Granularity of a Fact Table? What are Non-Additive Facts? What is a Factless Facts Table? What are Slowly Changing Dimensions (SCD)? SQL SERVER – Interview Questions and Answers – Frequently Asked Questions – Data Warehousing Concepts – Day 24 of 31 What is Hybrid Slowly Changing Dimension? What is BUS Schema? What is a Star Schema? What Snow Flake Schema? Differences between the Star and Snowflake Schema? What is Difference between ER Modeling and Dimensional Modeling? What is Degenerate Dimension Table? Why is Data Modeling Important? What is a Surrogate Key? What is Junk Dimension? What is a Data Mart? What is the Difference between OLAP and Data Warehouse? What is a Cube and Linked Cube with Reference to Data Warehouse? What is Snapshot with Reference to Data Warehouse? What is Active Data Warehousing? What is the Difference between Data Warehousing and Business Intelligence? What is MDS? Explain the Paradigm of Bill Inmon and Ralph Kimball. SQL SERVER – Azure Interview Questions and Answers – Guest Post by Paras Doshi – Day 25 of 31 Paras Doshi has submitted 21 interesting question and answers for SQL Azure. 1.What is SQL Azure? 2.What is cloud computing? 3.How is SQL Azure different than SQL server? 4.How many replicas are maintained for each SQL Azure database? 5.How can we migrate from SQL server to SQL Azure? 6.Which tools are available to manage SQL Azure databases and servers? 7.Tell me something about security and SQL Azure. 8.What is SQL Azure Firewall? 9.What is the difference between web edition and business edition? 10.How do we synchronize On Premise SQL server with SQL Azure? 11.How do we Backup SQL Azure Data? 12.What is the current pricing model of SQL Azure? 13.What is the current limitation of the size of SQL Azure DB? 14.How do you handle datasets larger than 50 GB? 15.What happens when the SQL Azure database reaches Max Size? 16.How many databases can we create in a single server? 17.How many servers can we create in a single subscription? 18.How do you improve the performance of a SQL Azure Database? 19.What is code near application topology? 20.What were the latest updates to SQL Azure service? 21.When does a workload on SQL Azure get throttled? SQL SERVER – Interview Questions and Answers – Guest Post by Malathi Mahadevan – Day 26 of 31 Malachi had asked a simple question which has several answers. Each answer makes you think and ponder about the reality of the IT world. Look at the simple question – ‘What is the toughest challenge you have faced in your present job and how did you handle it’? and its various answers. Each answer has its own story. SQL SERVER – Interview Questions and Answers – Guest Post by Rick Morelan – Day 27 of 31 Rick Morelan of Joes2Pros has written an excellent blog post on the subject how to find top N values. Most people are fully aware of how the TOP keyword works with a SELECT statement. After years preparing so many students to pass the SQL Certification I noticed they were pretty well prepared for job interviews too. Yes, they would do well in the interview but not great. There seemed to be a few questions that would come up repeatedly for almost everyone. Rick addresses similar questions in his lucid writing skills. 2012 Observation of Top with Index and Order of Resultset SQL Server has lots of things to learn and share. It is amazing to see how people evaluate and understand different techniques and styles differently when implementing. The real reason may be absolutely different but we may blame something totally different for the incorrect results. Read the blog post to learn more. How do I Record Video and Webcast How to Convert Hex to Decimal or INT Earlier I asked regarding a question about how to convert Hex to Decimal. I promised that I will post an answer with Due Credit to the author but never got around to post a blog post around it. Read the original post over here SQL SERVER – Question – How to Convert Hex to Decimal. Query to Get Unique Distinct Data Based on Condition – Eliminate Duplicate Data from Resultset The natural reaction will be to suggest DISTINCT or GROUP BY. However, not all the questions can be solved by DISTINCT or GROUP BY. Let us see the following example, where a user wanted only latest records to be displayed. Let us see the example to understand further. Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: Memory Lane, PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology

  Read the article

• I have finally traded my Blackberry in for a Droid!

  - by Bob Porter

  Over the years I have used a number of different types of phones. Windows Mobile, Blackberry, Nokia, and now Android. Until the Blackberry, which was my last phone (and I still have one issued from my office) I had never found a phone that “just worked” especially with email and messaging. The Blackberry did, and does, excel at those functions. My last personal phone was a Storm 1 which was Blackberry’s first touch screen phone. The Storm 2 was an improved version that fixed some screen press detection issues from the first model and it added Wifi. Over the last few years I have watched others acquire and fall in love with their ‘Droid’s including a number of iPhone users which surprised me. Our office has until recently only supported Blackberry phones, adding iPhones within the last year or so. When I spoke with our internal telecom folks they confirmed they were evaluating Android phones, but felt they still were not secure enough out of the box for corporate use and SOX compliance. That being said, as a personal phone, the Droid Rocks! I am impressed with its speed, the number of apps available, and the overall design. It is not as “flashy” as an iPhone but it does everything that I care about and more. The model I bought is the Motorola Droid 2 Global from Verizon. It is currently running Android 2.2 for it’s OS, 2.3 is just around the corner. It has 8 gigs of internal flash memory and can handle up to a 32 gig SDCard. (I currently have 2 8 gig cards, one for backups, and have ordered a 16 gig card!) Being a geek at heart, I “rooted” the phone which means gained superuser access to the OS on the phone. And opens a number of doors for further modifications down the road. Also being a geek meant I have already setup a development environment and built and deployed the obligatory “Hello Droid” application. I will be writing of my development experiences with this new platform here often, to start off I thought I would share my current application list to give you an idea what I am using. Zedge: http://market.android.com/details?id=net.zedge.android XDA: http://market.android.com/details?id=com.quoord.tapatalkxda.activity WRAL.com: http://market.android.com/details?id=com.mylocaltv.wral Wireless Tether: http://market.android.com/details?id=android.tether Winamp: http://market.android.com/details?id=com.nullsoft.winamp Win7 Clock: http://market.android.com/details?id=com.androidapps.widget.toggles.win7 Wifi Analyzer: http://market.android.com/details?id=com.farproc.wifi.analyzer WeatherBug: http://market.android.com/details?id=com.aws.android Weather Widget Forecast Addon: http://market.android.com/details?id=com.androidapps.weather.forecastaddon Weather & Toggle Widgets: http://market.android.com/details?id=com.androidapps.widget.weather2 Vlingo: http://market.android.com/details?id=com.vlingo.client VirtualTENHO-G: http://market.android.com/details?id=jp.bustercurry.virtualtenho_g Twitter: http://market.android.com/details?id=com.twitter.android TweetDeck: http://market.android.com/details?id=com.thedeck.android.app Tricorder: http://market.android.com/details?id=org.hermit.tricorder Titanium Backup PRO: http://market.android.com/details?id=com.keramidas.TitaniumBackupPro Titanium Backup: http://market.android.com/details?id=com.keramidas.TitaniumBackup Terminal Emulator: http://market.android.com/details?id=jackpal.androidterm Talking Tom Free: http://market.android.com/details?id=com.outfit7.talkingtom Stock Blue: http://market.android.com/details?id=org.adw.theme.stockblue ST: Red Alert Free: http://market.android.com/details?id=com.oldplanets.redalertwallpaper ST: Red Alert: http://market.android.com/details?id=com.oldplanets.redalertwallpaperplus Solitaire: http://market.android.com/details?id=com.kmagic.solitaire Skype: http://market.android.com/details?id=com.skype.raider Silent Time Lite: http://market.android.com/details?id=com.QuiteHypnotic.SilentTime ShopSavvy: http://market.android.com/details?id=com.biggu.shopsavvy Shopper: http://market.android.com/details?id=com.google.android.apps.shopper Shiny clock: http://market.android.com/details?id=com.androidapps.clock.shiny ShareMyApps: http://market.android.com/details?id=com.mattlary.shareMyApps Sense Glass ADW Theme: http://market.android.com/details?id=com.dtanquary.senseglassadwtheme ROM Manager: http://market.android.com/details?id=com.koushikdutta.rommanager Roboform Bookmarklet Installer: http://market.android.com/details?id=roboformBookmarkletInstaller.android.com RealCalc: http://market.android.com/details?id=uk.co.nickfines.RealCalc Package Buddy: http://market.android.com/details?id=com.psyrus.packagebuddy Overstock: http://market.android.com/details?id=com.overstock OMGPOP Toggle: http://market.android.com/details?id=com.androidapps.widget.toggle.omgpop OI File Manager: http://market.android.com/details?id=org.openintents.filemanager nook: http://market.android.com/details?id=bn.ereader MyAtlas-Google Maps Navigation ext: http://market.android.com/details?id=com.adaptdroid.navbookfree3 MSN Droid: http://market.android.com/details?id=msn.droid.im Matrix Live Wallpaper: http://market.android.com/details?id=com.jarodyv.livewallpaper.matrix LogMeIn: http://market.android.com/details?id=com.logmein.ignitionpro.android Liveshare: http://market.android.com/details?id=com.cooliris.app.liveshare Kobo: http://market.android.com/details?id=com.kobobooks.android Instant Heart Rate: http://market.android.com/details?id=si.modula.android.instantheartrate IMDb: http://market.android.com/details?id=com.imdb.mobile Home Plus Weather: http://market.android.com/details?id=com.androidapps.widget.skin.weather.homeplus Handcent SMS: http://market.android.com/details?id=com.handcent.nextsms H7C Clock: http://market.android.com/details?id=com.androidapps.widget.clock.skin.h7c GTasks: http://market.android.com/details?id=org.dayup.gtask GPS Status: http://market.android.com/details?id=com.eclipsim.gpsstatus2 Google Voice: http://market.android.com/details?id=com.google.android.apps.googlevoice Google Sky Map: http://market.android.com/details?id=com.google.android.stardroid Google Reader: http://market.android.com/details?id=com.google.android.apps.reader GoMarks: http://market.android.com/details?id=com.androappsdev.gomarks Goggles: http://market.android.com/details?id=com.google.android.apps.unveil Glossy Black Weather: http://market.android.com/details?id=com.androidapps.widget.weather.skin.glossyblack Fox News: http://market.android.com/details?id=com.foxnews.android Foursquare: http://market.android.com/details?id=com.joelapenna.foursquared FBReader: http://market.android.com/details?id=org.geometerplus.zlibrary.ui.android Fandango: http://market.android.com/details?id=com.fandango Facebook: http://market.android.com/details?id=com.facebook.katana Extensive Notes Pro: http://market.android.com/details?id=com.flufflydelusions.app.extensive_notes_donate Expense Manager: http://market.android.com/details?id=com.expensemanager Espresso UI (LightShow w/ Slide): http://market.android.com/details?id=com.jaguirre.slide.lightshow Engadget: http://market.android.com/details?id=com.aol.mobile.engadget Earth: http://market.android.com/details?id=com.google.earth Drudge: http://market.android.com/details?id=com.iavian.dreport Dropbox: http://market.android.com/details?id=com.dropbox.android DroidForums: http://market.android.com/details?id=com.quoord.tapatalkdrodiforums.activity DroidArmor ADW: http://market.android.com/details?id=mobi.addesigns.droidarmorADW Droid Weather Icons: http://market.android.com/details?id=com.androidapps.widget.weather.skins.white Droid 2 Bootstrapper: http://market.android.com/details?id=com.koushikdutta.droid2.bootstrap doubleTwist: http://market.android.com/details?id=com.doubleTwist.androidPlayer Documents To Go: http://market.android.com/details?id=com.dataviz.docstogo Digital Clock Widget: http://market.android.com/details?id=com.maize.digitalClock Desk Home: http://market.android.com/details?id=com.cowbellsoftware.deskdock Default Clock: http://market.android.com/details?id=com.androidapps.widget.clock.skins.defaultclock Daily Expense Manager: http://market.android.com/details?id=com.techahead.ExpenseManager ConnectBot: http://market.android.com/details?id=org.connectbot Colorized Weather Icons: http://market.android.com/details?id=com.androidapps.widget.weather.colorized Chrome to Phone: http://market.android.com/details?id=com.google.android.apps.chrometophone CardStar: http://market.android.com/details?id=com.cardstar.android Books: http://market.android.com/details?id=com.google.android.apps.books Black Ipad Toggle: http://market.android.com/details?id=com.androidapps.toggle.widget.skin.blackipad Black Glass ADW Theme: http://market.android.com/details?id=com.dtanquary.blackglassadwtheme Bing: http://market.android.com/details?id=com.microsoft.mobileexperiences.bing BeyondPod Unlock Key: http://market.android.com/details?id=mobi.beyondpod.unlockkey BeyondPod: http://market.android.com/details?id=mobi.beyondpod BeejiveIM: http://market.android.com/details?id=com.beejive.im Beautiful Widgets Animations Addon: http://market.android.com/details?id=com.levelup.bw.forecast Beautiful Widgets: http://market.android.com/details?id=com.levelup.beautifulwidgets Beautiful Live Weather: http://market.android.com/details?id=com.levelup.beautifullive BBC News: http://market.android.com/details?id=net.jimblackler.newswidget Barnacle Wifi Tether: http://market.android.com/details?id=net.szym.barnacle Barcode Scanner: http://market.android.com/details?id=com.google.zxing.client.android ASTRO SMB Module: http://market.android.com/details?id=com.metago.astro.smb ASTRO Pro: http://market.android.com/details?id=com.metago.astro.pro ASTRO Bluetooth Module: http://market.android.com/details?id=com.metago.astro.network.bluetooth ASTRO: http://market.android.com/details?id=com.metago.astro AppBrain App Market: http://market.android.com/details?id=com.appspot.swisscodemonkeys.apps App Drawer Icon Pack: http://market.android.com/details?id=com.adwtheme.appdrawericonpack androidVNC: http://market.android.com/details?id=android.androidVNC AndroidGuys: http://market.android.com/details?id=com.handmark.mpp.AndroidGuys Android System Info: http://market.android.com/details?id=com.electricsheep.asi AndFTP: http://market.android.com/details?id=lysesoft.andftp ADWTheme Red: http://market.android.com/details?id=adw.theme.red ADWLauncher EX: http://market.android.com/details?id=org.adwfreak.launcher ADW.Theme.One: http://market.android.com/details?id=org.adw.theme.one ADW.Faded theme: http://market.android.com/details?id=com.xrcore.adwtheme.faded ADW Gingerbread: http://market.android.com/details?id=me.robertburns.android.adwtheme.gingerbread Advanced Task Killer Free: http://market.android.com/details?id=com.rechild.advancedtaskkiller Adobe Reader: http://market.android.com/details?id=com.adobe.reader Adobe Flash Player 10.1: http://market.android.com/details?id=com.adobe.flashplayer Adobe AIR: http://market.android.com/details?id=com.adobe.air 3G Auto OnOff: http://market.android.com/details?id=com.yuantuo --- Generated by ShareMyApps http://market.android.com/details?id=com.mattlary.shareMyApps Sent from my Droid

  Read the article

• SSAS processing error: Client unable to establish connection; 08001; Encryption not supported on the client.; 08001

  - by Kevin Shyr

  After getting the cube to successfully deploy and process on Friday, I was baffled on Monday that the newly added dimension caused the cube processing to break.  I then followed the first instinct, discarded all my changes to reverted back to the version on Friday, and had no luck.  The error message (attached below) did not help as I was looking for some kind of SQL service error.  After examining the windows server log and the SQL server log, I just couldn't see anything wrong with it.After swearing for some time, and with the help of going off and working on something else for a while.  I came back to the solution and looked at the data source.  Even though I know I have never changed the provider (the default setup gave me SQL native client), I decided to change it and give OLE DB a try.This simple change allows my cube to process successfully again.  While I don't understand why the same settings that worked last week doesn't work this week, I don't have all the information to say with certainty that nothing has changed in the environment (firewall changes, server updates, etc.).SSAS processing error:<Batch >  <Parallel>    <Process xmlns:xsd="http://www.w3.org/2001/XMLSchema" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:ddl2="http://schemas.microsoft.com/analysisservices/2003/engine/2" xmlns:ddl2_2="http://schemas.microsoft.com/analysisservices/2003/engine/2/2" xmlns:ddl100_100="http://schemas.microsoft.com/analysisservices/2008/engine/100/100" xmlns:ddl200="http://schemas.microsoft.com/analysisservices/2010/engine/200" xmlns:ddl200_200="http://schemas.microsoft.com/analysisservices/2010/engine/200/200">      <Object>        <DatabaseID>DWH Sales Facts</DatabaseID>        <CubeID>DWH Sales Facts</CubeID>      </Object>      <Type>ProcessFull</Type>      <WriteBackTableCreation>UseExisting</WriteBackTableCreation>    </Process>  </Parallel></Batch>                Processing Dimension 'Date' completed.                                Errors and Warnings from Response                OLE DB error: OLE DB or ODBC error: A network-related or instance-specific error has occurred while establishing a connection to SQL Server. Server is not found or not accessible. Check if instance name is correct and if SQL Server is configured to allow remote connections. For more information see SQL Server Books Online.; 08001; Client unable to establish connection; 08001; Encryption not supported on the client.; 08001.                Errors in the high-level relational engine. A connection could not be made to the data source with the DataSourceID of 'DWH Sales Facts', Name of 'DWH Sales Facts'.                Errors in the OLAP storage engine: An error occurred while the dimension, with the ID of 'Currency', Name of 'Currency' was being processed.                Errors in the OLAP storage engine: An error occurred while the 'Currency Dim ID' attribute of the 'Currency' dimension from the 'DWH Sales Facts' database was being processed.                Internal error: The operation terminated unsuccessfully.                Server: The operation has been cancelled.

  Read the article

• Visual Studio 2010 Productivity Power Tool Extensions

  - by ScottGu

  Last month I blogged about the Extension Manager that is built-into VS 2010 – as well as about a cool VS 2010 PowerCommands extension that provides some extra features for Visual Studio.  The Visual Studio 2010 Extension Manager provides an easy way for developers to quickly find and install extensions and plugins that enhance the built-in functionality to VS 2010. New VS 2010 Productivity Power Tools Release Earlier this week Jason Zander announced the availability of a new VS 2010 Productivity Power Tools release that includes a bunch of great new VS 2010 extensions that provide a bunch of cool new functionality for you to take advantage of.  You can download and install the release for free here.  Some of the code editor improvements it provides include: Entire Line Highlighting: Makes it easier to track cursor location within the editor Entire Line Selection: Triple Clicking a line in the code editor now selects the entire line (like with MS Word) Code Block Movement: Use Alt+Up/Down Arrow now moves selected code blocks up/down in the editor Consistent Tabs vs. Spaces: Ensure consistent tab vs. space usage across your projects Colorized Parameters: It is now easier to see/identify method parameters Column Guide: You can now add vertical column guidelines to help with text alignment and sizes Align assignments: Makes it easier to line-up multiple variable assignments within your code HTML Clipboard Support: Copy/paste code from VS into an HTML buffer (useful for blogging!) Ctrl + Click Go to Definition: You can now hold down the Ctrl key and click a type to go to its definition It also includes several tab management improvements for managing document tabs within the IDE: Show Close Button in Tab Well: Shows a close button in document well for the active tab (like VS 2008 did) Colored Tabs: You can now select the color of each document tab by project or by regex Pinned Tabs: Enables you to pin tabs to keep them always visible and available Vertical Tabs: You can now show document tabs vertically to fit more tabs than normal Remove Tabs by Usage Order: Better behavior when adding new tabs and one needs to be hidden for space reasons Sort Tabs by Project: Tabs can be sorted by project they belong to, keeping them grouped together Sort Tabs Alphabetically: Tabs can be sorted alphabetically And last – but not least – it includes a new and improved “Add Reference” dialog: This new Add Reference dialog caches assembly information – which means it loads within a second or two (note: the very first time it still loads assembly data – but it then caches it and makes it fast afterwards). The new Add Reference dialog also now includes searching support – making it easier to find the assembly you are looking for. You can read more about all of the above improvements in Jason’s blog post about the release. New Visualization and Modeling Feature Pack Release Earlier this week we also shipped a new feature pack that adds additional modeling and code visualization features to VS 2010 Ultimate.  You can download it here. The Visualization and Modeling Feature Pack includes a bunch of great new capabilities including: Web Site Visualization: New support for generating a DGML visualization for ASP.NET projects C/C++ Native Code Visualization: New support for generating DGML diagrams for C/C++ projects Generate Code from UML Class Diagrams: You can now generate code from your UML diagrams Create UML Class Diagrams from Code: Create UML diagrams from existing code bases Import UML from XML: Import UML class, sequence, and use case elements from XMI 2.1 files Custom Validation Layer Rules: Write custom code to create, modify, and validate layer diagrams Jason’s blog post covers more about these features as well. Hope this helps, Scott P.S. In addition to blogging, I am also now using Twitter for quick updates and to share links. Follow me at: twitter.com/scottgu

  Read the article

• Silverlight Cream for March 26, 2010 -- #821

  - by Dave Campbell

  In this Issue: Max Paulousky, Christian Schormann, John Papa, Phani Raj, David Anson(-2-, -3-), Brad Abrams(-2-), and Jeff Wilcox(-2-, -3-). Shoutouts: Jeff Wilcox posted his material from mix and some preview TestFramework bits: Unit Testing Silverlight & Windows Phone Applications – talk now online At MIX10, Jeff Wilcox demo'd an app called "Peppermint"... here's the bleeding edge demo: “Peppermint” MIX demo sources Erik Mork and Co. have put out their weekly This Week In Silverlight 3.25.2010 Brad Abrams has all his materials posted for his MIX10 session Mix2010: Search Engine Optimization (SEO) for Microsoft Silverlight... including play-by-play of the demo and all source. Do you use Rooler? Well you should! Watch a video Pete Brown did with Pete Blois on Expression Blend, Windows Phone, Rooler Interested in Silverlight and XNA for WP7? Me too! Michael Klucher has a post outlining the two: Silverlight and XNA Framework Game Development and Compatibility From SilverlightCream.com: Modularity in Silverlight Applications - An Issue With ModuleInitializeException Max Paulousky has a truly ugly error trace listed by way of not having a reference listed, and the obvious simple solution. Next time he'll talk about the difficult situations. Using SketchFlow to Prototype for Windows Phone Christian Schormann has a tutorial up on using Expression Blend to develop for WP7 ... who better than Christian for that task?? Silverlight TV 18: WCF RIA Services Validation John Papa held forth with Nikhil Kothari on WCF RIA Services and validation just prior to MIX10, and was posted yesterday. Building SL3 applications using OData client Library with Vs 2010 RC Phani Raj walks through building an OData consumer in SL3, the first problem you're going to hit, and the easy solution to it. Tip: When creating a DependencyProperty, follow the handy convention of "wrapper+register+static+virtual" David Anson has a couple more of his 'Tips' up... this first is about Dependency Properties again... having a good foundation for all your Dependency Properties is a great way to avoid problems. Tip: Do not assign DependencyProperty values in a constructor; it prevents users from overriding them In the next post, David Anson talks about not assigning Dependency Property values in a constructor and gives one of the two ways to get around doing so. Tip: Set DependencyProperty default values in a class's default style if it's more convenient In his latest post, David Anson gives the second way to avoid setting a Dependency Property value in the constructor. Silverlight 4 + RIA Services - Ready for Business: Search Engine Optimization (SEO) Brad Abrams Abrams adds SEO to the tutorial series he's doing. He begins with his PDC09 session material on the subject and then takes off on a great detailed tutorial all with source. Silverlight 4 + RIA Services - Ready for Business: Localizing Business Application Brad Abrams then discusses localization and Silverlight in another detailed tutorial with all code included. Silverlight Toolkit and the Windows Phone: WrapPanel, and a few others Jeff Wilcox has a few WP7 posts I'm going to push today. This first is from earlier this week and is about using the Toolkit in WP7 and better than that, he includes the bits you need if all you want is the WrapPanel Data binding user settings in Windows Phone applications In the next one from yesterday, Jeff Wilcox demonstrates saving some user info in Isolated Storage to improve the user experience, and shares all the necessary plumbing files, and other external links as well. Displaying 2D QR barcodes in Windows Phone applications In a post from today, Jeff Wilcox ported his Silverlight 2D QR Barcode app from last year into WP7 ... just very cool... get the source and display your Microsoft Tag. Stay in the 'Light! Twitter SilverlightNews | Twitter WynApse | WynApse.com | Tagged Posts | SilverlightCream Join me @ SilverlightCream | Phoenix Silverlight User Group Technorati Tags: Silverlight    Silverlight 3    Silverlight 4    Windows Phone    MIX10

  Read the article

• OBIEE 11.1.1 - User Interface (UI) Performance Is Slow With Internet Explorer 8

  - by Ahmed A

  The OBIEE 11g UI is performance is slow in IE 8 and faster in Firefox.  For VPN or WAN users, it takes long time to display links on Dashboards via IE 8. Cause is IE 8 generates many HTTP 304 return calls and this caused the 11g UI slower when compared to the Mozilla FireFox browser. To resolve this issue, you can implement HTTP compression and caching. This is a best practice.Why use Web Server Compression / Caching for OBIEE? Bandwidth Savings: Enabling HTTP compression can have a dramatic improvement on the latency of responses. By compressing static files and dynamic application responses, it will significantly reduce the remote (high latency) user response time. Improves request/response latency: Caching makes it possible to suppress the payload of the HTTP reply using the 304 status code.  Minimizing round trips over the Web to re-validate cached items can make a huge difference in browser page load times. This screen shot depicts the flow and where the compression and decompression occurs: Solution: a. How to Enable HTTP Caching / Compression in Oracle HTTP Server (OHS) 11.1.1.x 1. To implement HTTP compression / caching, install and configure Oracle HTTP Server (OHS) 11.1.1.x for the bi_serverN Managed Servers (refer to "OBIEE Enterprise Deployment Guide for Oracle Business Intelligence" document for details). 2. On the OHS machine, open the file HTTP Server configuration file (httpd.conf) for editing. This file is located in the OHS installation directory.For example: ORACLE_HOME/Oracle_WT1/instances/instance1/config/OHS/ohs13. In httpd.conf file, verify that the following directives are included and not commented out: LoadModule expires_module "${ORACLE_HOME}/ohs/modules/mod_expires.soLoadModule deflate_module "${ORACLE_HOME}/ohs/modules/mod_deflate.so 4. Add the following lines in httpd.conf file below the directive LoadModule section and restart the OHS: Note: For the Windows platform, you will need to enclose any paths in double quotes ("), for example:Alias "/analytics ORACLE_HOME/bifoundation/web/app"<Directory "ORACLE_HOME/bifoundation/web/app"> Alias /analytics ORACLE_HOME/bifoundation/web/app#Pls replace the ORACLE_HOME with your actual BI ORACLE_HOME path<Directory ORACLE_HOME/bifoundation/web/app>#We don't generate proper cross server ETags so disable themFileETag noneSetOutputFilter DEFLATE# Don't compress imagesSetEnvIfNoCase Request_URI \.(?:gif|jpe?g|png)$ no-gzip dont-vary<FilesMatch "\.(gif|jpeg|png|js|x-javascript|javascript|css)$">#Enable future expiry of static filesExpiresActive onExpiresDefault "access plus 1 week"     #1 week, this will stops the HTTP304 calls i.e. generated by IE 8Header set Cache-Control "max-age=604800"</FilesMatch>DirectoryIndex default.jsp</Directory>#Restrict access to WEB-INF<Location /analytics/WEB-INF>Order Allow,DenyDeny from all</Location> Note: Make sure you replace above placeholder "ORACLE_HOME" to your correct path for BI ORACLE_HOME.For example: my BI Oracle Home path is /Oracle/BIEE11g/Oracle_BI1/bifoundation/web/app Important Notes: Above caching rules restricted to static files found inside the /analytics directory(/web/app). This approach is safer instead of setting static file caching globally. In some customer environments you may not get 100% performance gains in IE 8.0 browser. So in that case you need to extend caching rules to other directories with static files content. If OHS is installed on separate dedicated machine, make sure static files in your BI ORACLE_HOME (../Oracle_BI1/bifoundation/web/app) is accessible to the OHS instance. The following screen shot summarizes the before and after results and improvements after enabling compression and caching:

  Read the article

• Visual Studio 2010 SP1

  - by ScottGu

  Last week we shipped Service Pack 1 of Visual Studio 2010 and the Visual Studio Express Tools.  In addition to bug fixes and performance improvements, SP1 includes a number of feature enhancements.  This includes improved local help support, IntelliTrace support for 64-bit applications and SharePoint, built-in Silverlight 4 Tooling support in the box, unit testing support when targeting .NET 3.5, a new performance wizard for Silverlight, IIS Express and SQL CE Tooling support for web projects, HTML5 Intellisense for ASP.NET, and more.  TFS 2010 SP1 was also released last week, together with a new TFS Project Server Integration Pack and Load Test Feature Pack.  Brian Harry has a good blog post about the TFS updates here. VS 2010 SP1 Download Click here to download and install SP1 for all versions of Visual Studio (including express).  This installer examines what you have installed on your machine, and only downloads the servicing downloads necessary to update them to SP1.  The time it takes to download and update will consequently depend on what all you have installed.  Jon Galloway has a good blog post on tips to speed up the SP1 install by uninstalling unused components. Web Platform Installer Bundles In addition to the core VS 2010 SP1 installer, we have also put together two Web Platform Installer (WebPI) bundles that automate installing SP1 together with additional web-specific components: VS 2010 SP1 WebPI Bundle Visual Web Developer 2010 SP1 WebPI Bundle The above WebPI bundles automate installing: VS 2010/VWD 2010 SP1 ASP.NET MVC 3 (runtime + tools support) IIS 7.5 Express SQL Server Compact Edition 4.0 (runtime + tools support) Web Deployment 2.0 Only the components that are not already installed on your machine will be downloaded when you use the above WebPI bundles.  This means that you can run the WebPI bundle at any time (even if you have already installed SP1 or ASP.NET MVC 3) and not have to worry about wasting time downloading/installing these components again. Earlier this year I did two posts that discussed how to use IIS Express and SQL CE with ASP.NET projects in SP1.  Read the below posts to learn more about how to use them after you run the above bundles: Visual Studio 2010 SP1 and IIS Express Visual Studio 2010 SP1 and SQL CE for ASP.NET The above feature additions work with any web project type – including both ASP.NET Web Forms and ASP.NET MVC. Additional SP1 Notes Two additional notes about VS 2010 SP1: 1) One change we made between RTM and SP1 is that by default Visual Studio now uses software rendering instead of hardware acceleration when running on Windows XP.  We made this change because we’ve seen reports of (often inconsistent) performance issues caused by older video drivers.  Running in software mode eliminates these and delivers consistent speeds.  You can optionally re-enable hardware acceleration with SP1 using Visual Studio’s Tools->Options menu command – we did not remove support for HW acceleration on XP, we simply changed the default setting for it.  Jason Zander has written more details on the change and how to re-enable HW acceleration inside VS here. 2) We have discovered an issue where installing SP1 can cause TSQL intellisense within SQL Server Management Studio 2008 R2 to stop working (typing still works – but intellisense doesn’t show up).  The SQL team is investigating this now and I’ll post an update on how to fix this once more details are known.  Hope this helps, Scott P.S. I am also now using Twitter for quick updates and to share links. Follow me at: twitter.com/scottgu

  Read the article

• Why is my machine unable to mount my SMB drives ("CIFS VFS: Error connecting to socket. Aborting operation", return code -115)?

  - by downbeat

  I have a machine running Precise (12.04 x64), and I cannot mount my SMB drives (I have 3, we'll call them public, private and download). It used to work (a week or two ago) and I didn't touch fstab! The machine hosting the shares is a commercial NAS, and I'm not seeing anything that would indicate it's an issue with the NAS. I have an older machine which I updated to Precise at the same time (both fresh installed, not dist-upgrade), so should have a very similar configuration. It is not having any problems. I am not having problems on windows machines/partitions either, only one of my Precise machines. The two machines are using identical entries in fstab and identical /etc/samba/smb.conf files. I don't think I've ever changed smb.conf (has never mattered before). My fstab entries all basically look like this: //10.1.1.111/public /media/public cifs credentials=/home/downbeat/.credentials,iocharset=utf8,uid=downbeat,gid=downbeat,file_mode=0644,dir_mode=0755 0 0 Here's the dmesg output on boot: [ 51.162198] CIFS VFS: Error connecting to socket. Aborting operation [ 51.162369] CIFS VFS: cifs_mount failed w/return code = -115 [ 51.194106] CIFS VFS: Error connecting to socket. Aborting operation [ 51.194250] CIFS VFS: cifs_mount failed w/return code = -115 [ 51.198120] CIFS VFS: Error connecting to socket. Aborting operation [ 51.198243] CIFS VFS: cifs_mount failed w/return code = -115 There are no other errors I see in the dmesg output. Originally when I ran 'testparm -s', the output contained these lines ERROR: lock directory /var/run/samba does not exist ERROR: pid directory /var/run/samba does not exist Here's the samba related programs I have installed: $ dpkg --list|grep -i samba ii libpam-winbind 2:3.6.3-2ubuntu2.3 Samba nameservice and authentication integration plugins ii libwbclient0 2:3.6.3-2ubuntu2.3 Samba winbind client library ii nautilus-share 0.7.3-1ubuntu2 Nautilus extension to share folder using Samba ii python-smbc 1.0.13-0ubuntu1 Python bindings for Samba clients (libsmbclient) ii samba-common 2:3.6.3-2ubuntu2.3 common files used by both the Samba server and client ii samba-common-bin 2:3.6.3-2ubuntu2.3 common files used by both the Samba server and client ii winbind 2:3.6.3-2ubuntu2.3 Samba nameservice integration server $ dpkg --list|grep -i smb ii dmidecode 2.11-4 SMBIOS/DMI table decoder ii libsmbclient 2:3.6.3-2ubuntu2.3 shared library for communication with SMB/CIFS servers ii python-smbc 1.0.13-0ubuntu1 Python bindings for Samba clients (libsmbclient) ii smbclient 2:3.6.3-2ubuntu2.3 command-line SMB/CIFS clients for Unix ii smbfs 2:5.1-1ubuntu1 Common Internet File System utilities - compatibility package $ dpkg --list|grep -i cifs ii cifs-utils 2:5.1-1ubuntu1 Common Internet File System utilities ii libsmbclient 2:3.6.3-2ubuntu2.3 shared library for communication with SMB/CIFS servers ii smbclient 2:3.6.3-2ubuntu2.3 command-line SMB/CIFS clients for Unix I originally noticed that my other machine had "libpam-winbind" and "nautilus-share" installed and the machine with the issue did not. Installing those two packages solved my errors with 'testparm -s', but did not fix my issue. Finally, I tried to purge and reinstall these packages smbclient smbfs cifs-utils samba-common samba-common-bin Still no luck. Again, it used to work; now it doesn't. Very similarly configured machine works (but some packages are out of date on the working machine). The NAS has only one interface/IP address, nmblookup works to find it's IP from it's hostname (from the machine with the issue) and it responds to a ping. Please any help would be great. I've been searching on AskUbuntu, SuperUser, ubuntuforums and plain old search engines for a week now and it's driving me crazy!

  Read the article

• Silverlight Cream for February 10, 2011 -- #1045

  - by Dave Campbell

  In this Issue: Mark Monster, Jaime Rodriguez, Mark Hopkins, WindowsPhoneGeek, David Anson, Jesse Liberty, Jeremy Likness, Martin Krüger(-2-), Beth Massi, Joost van Schaik, Laurent Bugnion, and Arik Poznanski. Above the Fold: Silverlight: "Parsing the Visual Tree with LINQ" Jeremy Likness WP7: "Silverlight-ready PNG encoder implementation shows one way to use .NET IEnumerables effectively" David Anson Lightswitch: "How to Send Automated Appointments from a LightSwitch Application" Beth Massi Shoutouts: Be sure to visit SilverlightShow... check out their top hits last week: SilverlightShow for Jan 31- Feb 06, 2011 Jaime Rodriguez has a post up that all the WP7 folks will be interested in: FAQ about copy paste functionality in upcoming release From SilverlightCream.com: Make use of WCF FaultContracts in Silverlight clients Mark Monster takes a shot at answering “The remote server returned an error: NotFound” while connecting to a WCF Service problem we all see. Communication between HTML in WebBrowser and Silverlight app Jaime Rodriguez responds to questions he received about communication between HTML and SIlverlight with this post about the bi-directional communication between the control and HTML. WP7 - Real Apps, Real Code Mark Hopkins has a post up about some WP7 starter kits that you can get all the source for and actually download the app from the Marketplace first to see if it interests you! WP7 AboutPrompt in depth WindowsPhoneGeek has this cool post up about the AboutPrompt from the Coding4Fun toolkit in detail... great diagrams showing where all the elements are and code examples with images. Silverlight-ready PNG encoder implementation shows one way to use .NET IEnumerables effectively David Anson describes why he took it upon himself to write his own png encoder for Silverlight... and we all thank him for doing so and providing us with the code! Navigation 101–Cancelling Navigation Jesse Liberty's latest WP7 From Scratch episode is up (number 32), and he's talking about Navigation and how to cancel it if you need to. Parsing the Visual Tree with LINQ Jeremy Likness demonstrates using LINQ to rat out information in the visual tree of your XAML. To Quote Jeremy: "you can easily check for intersections between elements and find any type of element no matter how deep within the tree it is". SpriteAnimationBehavior Martin Krüger has a couple more fun things in the Expression Gallery that I haven't discussed. First up is a behavior that animates up to 999 images and lets you control the FramesPerSecond... great demo on the ExpressionGallery to play with. Second alternative: Storyboard should not start before the Silverlight application is loaded Martin Krüger's latest is a way to programmatically wait for the Loaded event so that you know you can let your animations fly. How to Send Automated Appointments from a LightSwitch Application Beth Massi's latest Lightswitch post follows up her Outlook automation one with sending appointments using the standard iCalendar format... all the code included of course. The case for the Bindable Application Bar for Windows Phone 7 Joost van Schaik posts about a bindable Application Bar for your WP7 apps... grab the code and don't leave home without it :) MVVM Light V4 preview (BL0014) release notes Laurent Bugnion posted an update to MVVMLight to Codeplex a couple days ago. This is an early preview of what he plans on having in version 4, so check out the post for what's new and fun. Search Digg on Windows Phone 7 Arik Poznanski followed up his RSS post from last week with this one on searching Digg on WP7... and he's discussing and providing a utility class for doing it. Stay in the 'Light! Twitter SilverlightNews | Twitter WynApse | WynApse.com | Tagged Posts | SilverlightCream Join me @ SilverlightCream | Phoenix Silverlight User Group Technorati Tags: Silverlight    Silverlight 3    Silverlight 4    Windows Phone MIX10

  Read the article

• Session Update from IASA 2010

  - by [email protected]

  Below: Tom Kristensen, senior vice president at Marsh US Consumer, and Roger Soppe, CLU, LUTCF, senior director of insurance strategy, Oracle Insurance. Tom and Roger participated in a panel discussion on policy administration systems this week at IASA 2010. This week was the 82nd Annual IASA Educational Conference & Business Show held in Grapevine, Texas. While attending the conference, I had the pleasure of serving as a panelist in one of many of the outstanding sessions conducted this year. The session - entitled "Achieving Business Agility and Promoting Growth with a Modern Policy Administration System" - included industry experts Steve Forte from OneShield, Mike Sciole of IFG Companies, and Tom Kristensen, senior vice president at Marsh US Consumer. The session was conducted as a panel discussion and focused on how insurers can leverage best practices to mitigate risk while enabling rapid product innovation through a modern policy administration system. The panelists offered insight into business and technical challenges for both Life & Annuity and Property & Casualty carriers. The session had three primary learning objectives: Identifying how replacing a legacy system with a more modern policy administration solution can deliver agility and growth Identifying how processes and system should be re-engineered or replaced in order to improve speed-to-market and product support Uncovering how to leverage best practices to mitigate risk during a migration to a new platform Tom Kristensen, who is an industry veteran with over 20 years of experience, was able was able to offer a unique perspective as a business process outsourcer (BPO). Marsh US Consumer is currently implementing both the Oracle Insurance Policy Administration solution and the Oracle Revenue Management and Billing platform while at the same time implementing a new BPO customer. Tom offered insight on the need to replace their aging systems and Marsh's ability to drive new products and processes with a modern solution. As a best practice, their current project has empowered their business users to play a major role in both the requirements gathering and configuration phases. Tom stated that working with a modern solution has also enabled his organization to use a more agile implementation methodology and get hands-on experience with the software earlier in the project. He also indicated that Marsh was encouraged by how quickly it will be able to implement new products, which is another major advantage of a modern rules-based system. One of the more interesting issues was raised by an audience member who asked, "With all the vendor solutions available in North American and across Europe, what is going to make some of them more successful than others and help ensure their long term success?" Panelist Mike Sciole, IFG Companies suggested that carriers do their due diligence and follow a structured evaluation process focusing on vendors who demonstrate they have the "cash to invest in long term R&D" and evaluate audited annual statements for verification. Other panelists suggested that the vendor space will continue to evolve and those with a strong strategy focused on the insurance industry and a solid roadmap will likely separate themselves from the rest. The session concluded with the panelists offering advice about not being afraid to evaluate new modern systems. While migrating to a new platform can be challenging and is typically only undertaken every 15+ years by carriers, the ability to rapidly deploy and manage new products, create consistent processes to better service customers, and the ability to manage their business more effectively, transparently and securely are well worth the effort. Roger A.Soppe, CLU, LUTCF, is the Senior Director of Insurance Strategy, Oracle Insurance.

  Read the article

• Announcing the ASP.NET and Web Tools 2012.2 Release Candidate

  - by ScottGu

  This week the ASP.NET and Visual Web Developer teams delivered the Release Candidate of the ASP.NET and Web Tools 2012.2 update (formerly ASP.NET Fall 2012 Update BUILD Prerelease). This update extends the existing ASP.NET runtime and adds new web tooling to Visual Studio 2012. Whether you use Web Forms, MVC, Web API, or any other ASP.NET technology, there is something cool in this update for you. You can download and install the RC today: http://www.asp.net/vnext. Great ASP.NET Enhancements This update adds new ASP.NET templates and features, including: New ASP.NET MVC templates. Creating Facebook applications just became easier using the new Facebook Application template. In just a few easy steps you can create a Facebook application that gets data from the logged in user as well as integrates with their friends. A new Single Page Application template allows developers to build interactive client-side web apps using Knockout, jQuery, and ASP.NET Web API. Real-time communication support with ASP.NET SignalR.  This enables you to easily take advantage of the new WebSocket support in .NET 4.5, while also automatically degrading to long-polling and other protocols for older clients.  If you haven’t tried SignalR yet you should – it is awesome. New ASP.NET Web API functionality, including support for OData, integrated tracing, and automatically generating help page documentation for your API. New ASP.NET Friendly URL functionality. This new feature makes it very easy for Web Forms developers to generate cleaner looking URLs (without the .aspx extension). The Friendly URLs feature also makes it easier for developers to add mobile support to their applications with support for mobile .ASPX pages and  supporting switching between desktop and mobile views. It can be used with existing ASP.NET v4.0 applications. Visual Studio 2012 Web publishing enhancements. Web site projects now have the same publish experience as web application projects (including to Windows Azure Web Sites), and you can selectively publish files, see the differences between local and remote files, and update local to remote files or vice versa. Visual Studio 2012 Page Inspector enhancements. JavaScript selection mapping is now supported, and you can CSS updates in real-time. Visual Studio 2012 editor support for Knockout IntelliSense and pasting JSON as a .NET class (which makes it even easier to consume Web APIs from others). Visual Studio 2012 Project Template updates, including the latest versions of jQuery, jQuery UI, jQuery Validation, Modernirz, Knockout and more… How it is delivered You can download and install an integrated setup that contains the above enhancements today from http://www.asp.net/vnext. The new runtime functionality is delivered to ASP.NET via additional NuGet packages. This means that installing this update does not make any changes to the existing ASP.NET binaries, and thus does not cause any compatibility issues with existing projects. New projects will contain the new functionality and existing projects can be updated with the new NuGet packages. Summary Web development is changing, and ASP.NET is rapidly delivering new capabilities to developers that help them take full advantage of new capabilities.  The ASP.NET and Web Tools 2012.2 update installs in minutes without altering the current ASP.NET run time components. For a complete description see the Release Notes. Next week I plan to publish a tutorial showing how to build a cool Facebook application using the new Facebook template. Hope this helps, Scott P.S. In addition to blogging, I am also now using Twitter for quick updates and to share links. Follow me at: twitter.com/scottgu

  Read the article

• The DOS DEBUG Environment

  - by MarkPearl

  Today I thought I would go back in time and have a look at the DEBUG command that has been available since the beginning of dawn in DOS, MS-DOS and Microsoft Windows. up to today I always knew it was there, but had no clue on how to use it so for those that are interested this might be a great geek party trick to pull out when you want the awe the younger generation and want to show them what “real” programming is about. But wait, you will have to do it relatively quickly as it seems like DEBUG was finally dumped from the Windows group in Windows 7. Not to worry, pull out that Windows XP box which will get you even more geek points and you can still poke DEBUG a bit. So, for those that are interested and want to find out a bit about the history of DEBUG read the wiki link here. That all put aside, lets get our hands dirty.. How to Start DEBUG in Windows Make sure your version of Windows supports DEBUG. Open up a console window Make a directory where you want to play with debug – in my instance I called it C221 Enter the directory and type Debug You will get a response with a – as illustrated in the image below…   The commands available in DEBUG There are several commands available in DEBUG. The most common ones are A (Assemble) R (Register) T (Trace) G (Go) D (Dump or Display) U (Unassemble) E (Enter) P (Proceed) N (Name) L (Load) W (Write) H (Hexadecimal) I (Input) O (Output) Q (Quit) I am not going to cover all these commands, but what I will do is go through a few of them briefly. A is for Assemble Command (to write code) The A command translates assembly language statements into machine code. It is quite useful for writing small assembly programs. Below I have written a very basic assembly program. The code typed out is as follows mov ax,0015 mov cx,0023 sub cx,ax mov [120],al mov cl,[120]A nop R is for Register (to jump to a point in memory) The r command turns out to be one of the most frequent commands you will use in DEBUG. It allows you to view the contents of registers and to change their values. It can be used with the following combinations… R – Displays the contents of all the registers R f – Displays the flags register R register_name – Displays the contents of a specific register All three methods are illustrated in the image above T is for Trace (To execute a program step by step) The t command allows us to execute the program step by step. Before we can trace the program we need to point back to the beginning of the program. We do this by typing in r ip, which moves us back to memory point 100. We then type trace which executes the first line of code (line 100) (As shown in the image below starting from the red arrow). You can see from the above image that the register AX now contains 0015 as per our instruction mov ax,0015 You can also see that the IP points to line 0103 which has the MOV CX,0023 command If we type t again it will now execute the second line of the program which moves 23 in the cx register. Again, we can see that the line of code was executed and that the CX register now holds the value of 23. What I would like to highlight now is the section underlined in red. These are the status flags. The ones we are going to look at now are 1st (NV), 4th (PL), 5th (NZ) & 8th (NC) NV means no overflow, the alternate would be OV PL means that the sign of the previous arithmetic operation was Plus, the alternate would be NG (Negative) NZ means that the results of the previous arithmetic operation operation was Not Zero, the alternate would be ZR NC means that No final Carry resulted from the previous arithmetic operation. CY means that there was a final Carry. We could now follow this process of entering the t command until the entire program is executed line by line. G is for Go (To execute a program up to a certain line number) So we have looked at executing a program line by line, which is fine if your program is minuscule BUT totally unpractical if we have any decent sized program. A quicker way to run some lines of code is to use the G command. The ‘g’ command executes a program up to a certain specified point. It can be used in connection with the the reset IP command. You would set your initial point and then run the G command with the line you want to end on. P is for Proceed (Similar to trace but slightly more streamlined) Another command similar to trace is the proceed command. All that the p command does is if it is called and it encounters a CALL, INT or LOOP command it terminates the program execution. In the example below I modified our example program to include an int 20 at the end of it as illustrated in the image below… Then when executing the code when I encountered the int 20 command I typed the P command and the program terminated normally (illustrated below). D is for Dump (or for those more polite Display) So, we have all these assembly lines of code, but if you have ever opened up an exe or com file in a text/hex editor, it looks nothing like assembly code. The D command is a way that we can see what our code looks like in memory (or in a hex editor). If we examined the image above, we can see that Debug is storing our assembly code with each instruction following immediately after the previous one. For instance in memory address 110 we have int and 111 we have 20. If we examine the dump of memory we can see at memory point 110 CD is stored and at memory point 111 20 is stored. U is for Unassemble (or Convert Machine code to Assembly Code) So up to now we have gone through a bunch of commands, but probably one of the most useful is the U command. Let’s say we don’t understand machine code so well and so instead we want to see it in its equivalent assembly code. We can type the U command followed by the start memory point, followed by the end memory point and it will show us the assembly code equivalent of the machine code. E is for a bunch of things… The E command can be used for a bunch of things… One example is to enter data or machine code instructions directly into memory. It can also be used to display the contents of memory locations. I am not going to worry to much about it in this post. N / L / W is for Name, Load & Write So we have written out assembly code in debug, and now we want to save it to disk, or write it as a com file or load it. This is where the N, L & W command come in handy. The n command is used to give a name to the executable program file and is pretty simple to use. The w command is a bit trickier. It saves to disk all the memory between point bx and point cx so you need to specify the bx memory address and the cx memory address for it to write your code. Let’s look at an example illustrated below. You do this by calling the r command followed by the either bx or cx. We can then go to the directory where we were working and will see the new file with the name we specified. The L command is relatively simple. You would first specify the name of the file you would like to load using the N command, and then call the L command. Q is for Quit The last command that I am going to write about in this post is the Q command. Simply put, calling the Q command exits DEBUG. Commands we did not Cover Out of the standard DEBUG commands we covered A, T, G, D, U, E, P, R, N, L & W. The ones we did not cover were H, I & O – I might make mention of these in a later post, but for the basics they are not really needed. Some Useful Resources Please note this post is based on the COS2213 handouts for UNISA A Guide to DEBUG - http://mirror.href.com/thestarman/asm/debug/debug.htm#NT

  Read the article

• Podcast Show Notes: Collaborate 10 Wrap-Up - Part 1

  - by Bob Rhubart

  OK, I know last week I promised you a program featuring Oracle ACE Directors Mike van Alst (IT-Eye) and Jordan Braunstein (TUSC) and The Definitive Guide to SOA: Oracle Service Bus author Jeff Davies. But things happen. In this case, what happened was Collaborate 10 in Las Vegas. Prior to the event I asked Oracle ACE Director and OAUG board member Floyd Teter to see if he could round up a couple of people at the event for an impromtu interview over Skype (I was here in Cleveland) to get their impressions of the event. Listen to Part 1 Floyd, armed with his brand new iPad, went above and beyond the call of duty. At the appointed hour, which turned out to be about hour after the close of Collaborate 10,  Floyd had gathered nine other people to join him in a meeting room somewhere in the Mandalay Bay Convention Center. Here’s the entire roster: Floyd Teter - Project Manager at Jet Propulsion Lab, OAUG Board Blog | Twitter | LinkedIn | Oracle Mix | Oracle ACE Profile Mark Rittman - EMEA Technical Director and Co-Founder, Rittman Mead,  ODTUG Board Blog | Twitter | LinkedIn | Oracle Mix | Oracle ACE Profile Chet Justice - OBI Consultant at BI Wizards Blog | Twitter | LinkedIn | Oracle Mix | Oracle ACE Profile Elke Phelps - Oracle Applications DBA at Humana, OAUG SIG Chair Blog | LinkedIn | Oracle Mix | Book | Oracle ACE Profile Paul Jackson - Oracle Applications DBA at Humana Blog | LinkedIn | Oracle Mix | Book Srini Chavali - Enterprise Database & Tools Leader at Cummins, Inc Blog | LinkedIn | Oracle Mix Dave Ferguson – President, Oracle Applications Users Group LinkedIn | OAUG Profile John King - Owner, King Training Resources Website | LinkedIn | Oracle Mix Gavyn Whyte - Project Portfolio Manager at iFactory Consulting Blog | Twitter | LinkedIn | Oracle Mix John Nicholson - Channels & Alliances at Greenlight Technologies Website | LinkedIn Big thanks to Floyd for assembling the panelists and handling the on-scene MC/hosting duties.  Listen to Part 1 On a technical note, this discussion was conducted over Skype, using Floyd’s iPad, placed in the middle of the table.  During the call the audio was fantastic – the iPad did a remarkable job. Sadly, the Technology Gods were not smiling on me that day. The audio set-up that I tested successfully before the call failed to deliver when we first connected – I could hear the folks in Vegas, but they couldn’t hear me. A frantic, last-minute adjustment appeared to have fixed that problem, and the audio in my headphones from both sides of the conversation was loud and clear.  It wasn’t until I listened to the playback that I realized that something was wrong. So the audio for Vegas side of the discussion has about the same fidelity as a cell phone. It’s listenable, but disappointing when compared to what it sounded like during the discussion. Still, this was a one shot deal, and the roster of panelists and the resulting conversation was too good and too much fun to scrap just because of an unfortunate technical glitch.   Part 2 of this Collaborate 10 Wrap-Up will run next week. After that, it’s back on track with the previously scheduled program. So stay tuned: RSS del.icio.us Tags: oracle,otn,collborate 10,c10,oracle ace program,archbeat,arch2arch,oaug,odtug,las vegas Technorati Tags: oracle,otn,collborate 10,c10,oracle ace program,archbeat,arch2arch,oaug,odtug,las vegas

  Read the article

• Oracle WebCenter: Extending Oracle Applications & Oracle Fusion Applications

  - by kellsey.ruppel(at)oracle.com

  Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Calibri","sans-serif";} -- Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Calibri","sans-serif";}We’ve talked in previous weeks about the key goals of the new release of WebCenter are providing a Modern User Experience, unparalleled Application Integration, converging all the best of the existing portal platforms into WebCenter and delivering a Common User Experience Architecture.  We’ve provided an overview of Oracle WebCenter and discussed some of the other key goals in previous weeks, and this week, we’ll focus on how the new release of Oracle WebCenter extends Oracle Applications and Fusion Applications.When we talk about the new release of Oracle WebCenter, we really emphasize to customers that they can leverage their existing investments and benefit from WebCenter’s Complete, Open and Integrated platform. To summarize what we mean here, Oracle WebCenter is:COMPLETEComprehensive platform for Portals/Websites, Composite Applications with integrated Social/Collaboration services and Content Management infrastructureOPENStandards support improves reuse of existing resources and extends the value of existing systemsINTEGRATEDImplicit integration with Oracle Applications, Oracle Fusion Applications & other enterprise applicationsWith all the existing enterprise applications in Oracle’s application portfolio, in the new release of WebCenter we’ve got a set of pre-built catalogs that customers can use directly to get at all the portlet resources certified and available from Oracle.  It provides customers with a ready-to-use view of their application resources.  And since WebCenter provides seamless support for building these portlets/components in a professional IDE like JDeveloper or from within a Browser, developers and business analysts can quickly assemble the information they require for their existing application investment.  In addition, we’ve taken all the user flows and patterns that we’ve learned in building Fusion Applications and focused on making it dramatically easier to use tools to create reusable application UI components. In this way, one team in the organization using an application can share their components with other teams.  And more importantly, the new team can make changes to the component without breaking the original component.  When tied to enterprise applications, this capability is extremely powerful.  This is what Oracle means when they talk about Enterprise Mashups.  And finally, we’ve provided an innovative way to go well beyond traditional “on the glass” integration by enabling business transactions for the existing applications direct integration using activity streams. This delivers aggregated and “on time” delivery of information to the business users based on what‘s happening in the enterprise that is relevant to their particular job function.  Most importantly, it ties into the personalization interactions discussed earlier so that it can help target information to you directly based on past interactions.  Application integration is key to making businesses function more efficiently with these new Enterprise 2.0 technologies.Keep checking back this week as we share more information on how WebCenter is the most complete, open and integrated modern user experience platform and show key ways WebCenter can extend Oracle Applications & Oracle Fusion Applications.

  Read the article

• Meet our Interns: Adam and Hanadi

  - by Maria Sandu

  Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 This week, we’d like to introduce you to two of our ECEMEA Interns, Adam and Hanadi. They’re based in different countries and are part of different teams; however they both have the same enthusiasm in being an Intern at Oracle. “Hi! I’m Adam (Bachelor of Accounting Science & CIMA Diploma in Management Accounting), a member of the Oracle Applications Pre-sales team in Johannesburg, South Africa. Joining Oracle has been a truly inspiring experience thus far. My first week at Oracle has been one of insight and learning. I have had the opportunity to meet and interact with industry leading software solution professionals. Gaining insight into a mammoth multinational company has changed my perception on how things work and has truly opened my eyes to the world of business. Having the privilege of joining the Oracle Graduate Program has afforded me the chance to take advantage of countless training opportunities as well as the chance to learn about Information Technology in a practical manner which is vital to most businesses in today’s modern environment.” “Hi! I’m Hanadi, an Oracle 2013 Sales Intern from Saudi Arabia. I received my BSc in Information Technology from King Saud University and immediately after graduating I applied for the internship at Oracle. I thought it was an incredible opportunity and a great way to shift from college life to career life through learning and practicing in an environment with such high standards. At the beginning, I was a bit nervous in joining the serious business world, but once I joined, I found the program very organized and everyone was extremely helpful, which made it easier for us, as interns, to learn faster. If you are a self-motivated, committed person, who has initiative, accepts challenges, has good soft skills and some technical experience, I would definitely advice you to take a chance and apply for the program once you graduate. Best of luck!” Get the latest updates from the ECEMEA Sales and Presales Internship Programme 2013 by following #Oracleinterns on Twitter or visiting CampusatOracle Facebook Page! /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-family:"Calibri","sans-serif"; mso-ascii- mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi- mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;}

  Read the article

• Microsoft hosting free Hyper-V training for VMware Pros

  - by Ryan Roussel

  Microsoft will be hosting free training for virtualization professionals focused on Hyper-V, System Center, and virtualization architecture.  Details are below:   Just one week after Microsoft Management Summit 2011 (MMS), Microsoft Learning will be hosting an exclusive three-day Jump Start class specially tailored for VMware and Microsoft virtualization technology pros.  Registration for “Microsoft Virtualization for VMware Professionals” is open now and will be delivered as an online class on March 29-31, 2010 from 10:00am-4:00pm PDT.    The course is COMPLETELY FREE and OPEN TO ANYONE!  Please share with your customers, blog, Tweet, etc. – help us get the word out to strengthen support for Microsoft’s virtualization offerings. What’s the high-level overview? This cutting edge course will feature expert instruction and real-world demonstrations of Hyper-V and brand new releases from System Center Virtual Machine Manager 2012 Beta (many of which will be announced just one week earlier at MMS).  Register Now!   Day 1 will focus on “Platform” (Hyper-V, virtualization architecture, high availability & clustering) 10:00am – 10:30pm PDT:  Virtualization 360 Overview 10:30am – 12:00pm:  Microsoft Hyper-V Deployment Options & Architecture 1:00pm – 2:00pm:  Differentiating Microsoft and VMware (terminology, etc.) 2:00pm – 4:00pm:  High Availability & Clustering Day 2 will focus on “Management” (System Center Suite, SCVMM 2012 Beta, Opalis, Private Cloud solutions) 10:00am – 11:00pm PDT:  System Center Suite Overview w/ focus on DPM 11:00am – 12:00pm:  Virtual Machine Manager 2012 | Part 1 1:00pm –   1:30pm:  Virtual Machine Manager 2012 | Part 2 1:30pm – 2:30pm:  Automation with System Center Opalis & PowerShell 2:30pm – 4:00pm:  Private Cloud Solutions, Architecture & VMM SSP 2.0 Day 3 will focus on “VDI” (VDI Infrastructure/architecture, v-Alliance, application delivery via VDI) 10:00am – 11:00pm PDT:  Virtual Desktop Infrastructure (VDI) Architecture | Part 1 11:00am – 12:00pm:  Virtual Desktop Infrastructure (VDI) Architecture | Part 2 1:00pm – 2:30pm:  v-Alliance Solution Overview 2:30pm – 4:00pm:  Application Delivery for VDI     Every section will be team-taught by two of the most respected authorities on virtualization technologies: Microsoft Technical Evangelist Symon Perriman and leading Hyper-V, VMware, and XEN infrastructure consultant, Corey Hynes Who is the target audience for this training? Suggested prerequisite skills include real-world experience with Windows Server 2008 R2, virtualization and datacenter management. The course is tailored to these types of roles: · IT Professional · IT Decision Maker · Network Administrators & Architects · Storage/Infrastructure Administrators & Architects How do I to register and learn more about this great training opportunity? · Register: Visit the Registration Page and sign up for all three sessions · Blog: Learn more from the Microsoft Learning Blog · Twitter: Here are a few posts you can retweet: o Mar. 29-31 "Microsoft #Virtualization for VMware Pros" @SymonPerriman Corey Hynes http://bit.ly/JS-Hyper-V @MSLearning #Hyper-V o @SysCtrOpalis Mar. 29-31 "Microsoft #Virtualization for VMware Pros" @SymonPerriman Corey Hynes http://bit.ly/JS-Hyper-V #Hyper-V o Learn all the cool new features in Hyper-V & System Center 2012! SCVMM, Self-Service Portal 2.0, http://bit.ly/JS-Hyper-V #Hyper-V #Opalis What is a “Jump Start” course? A “Jump Start” course is “team-taught” by two expert instructors in an engaging radio talk show style format. The idea is to deliver readiness training on strategic and emerging technologies that drive awareness at scale before Microsoft Learning develops mainstream Microsoft Official Courses (MOC) that map to certifications.  All sessions are professionally recorded and distributed through MS Showcase, Channel 9, Zune Marketplace and iTunes for broader reach.

  Read the article

< Previous Page | 149 150 151 152 153 154 155 156 157 158 159 160  | Next Page >